Updates:
Internet Engineering Task Force (IETF) J. Touch
Request for Comments: 6864 USC/ISI
Updates: 791, 1122, 2003 February 2013
Category: Standards Track
ISSN: 2070-1721
Updated Specification of the IPv4 ID Field
Abstract
The IPv4 Identification (ID) field enables fragmentation and
reassembly and, as currently specified, is required to be unique
within the maximum lifetime for all datagrams with a given source
address/destination address/protocol tuple. If enforced, this
uniqueness requirement would limit all connections to 6.4 Mbps for
typical datagram sizes. Because individual connections commonly
exceed this speed, it is clear that existing systems violate the
current specification. This document updates the specification of
the IPv4 ID field in RFCs 791, 1122, and 2003 to more closely reflect
current practice and to more closely match IPv6 so that the field's
value is defined only when a datagram is actually fragmented. It
also discusses the impact of these changes on how datagrams are used.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc6864.
Touch Standards Track [Page 1]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ....................................................3
2. Conventions Used in This Document ...............................3
3. The IPv4 ID Field ...............................................4
3.1. Uses of the IPv4 ID Field ..................................4
3.2. Background on IPv4 ID Reassembly Issues ....................5
4. Updates to the IPv4 ID Specification ............................6
4.1. IPv4 ID Used Only for Fragmentation ........................7
4.2. Encouraging Safe IPv4 ID Use ...............................8
4.3. IPv4 ID Requirements That Persist ..........................8
5. Impact of Proposed Changes ......................................9
5.1. Impact on Legacy Internet Devices ..........................9
5.2. Impact on Datagram Generation .............................10
5.3. Impact on Middleboxes .....................................11
5.3.1. Rewriting Middleboxes ..............................11
5.3.2. Filtering Middleboxes ..............................12
5.4. Impact on Header Compression ..............................12
5.5. Impact of Network Reordering and Loss .....................13
5.5.1. Atomic Datagrams Experiencing Reordering or Loss ...13
5.5.2. Non-atomic Datagrams Experiencing
Reordering or Loss .................................14
6. Updates to Existing Standards ..................................14
6.1. Updates to RFC 791 ........................................14
6.2. Updates to RFC 1122 .......................................15
6.3. Updates to RFC 2003 .......................................16
7. Security Considerations ........................................16
8. References .....................................................17
8.1. Normative References ......................................17
8.2. Informative References ....................................17
9. Acknowledgments ................................................19
Touch Standards Track [Page 2]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
1. Introduction
In IPv4, the Identification (ID) field is a 16-bit value that is
unique for every datagram for a given source address, destination
address, and protocol, such that it does not repeat within the
maximum datagram lifetime (MDL) [RFC791] [RFC1122]. As currently
specified, all datagrams between a source and destination of a given
protocol must have unique IPv4 ID values over a period of this MDL,
which is typically interpreted as two minutes and is related to the
recommended reassembly timeout [RFC1122]. This uniqueness is
currently specified as for all datagrams, regardless of fragmentation
settings.
Uniqueness of the IPv4 ID is commonly violated by high-speed devices;
if strictly enforced, it would limit the speed of a single protocol
between two IP endpoints to 6.4 Mbps for typical MTUs of 1500 bytes
(assuming a 2-minute MDL, using the analysis presented in [RFC4963]).
It is common for a single connection to operate far in excess of
these rates, which strongly indicates that the uniqueness of the IPv4
ID as specified is already moot. Further, some sources have been
generating non-varying IPv4 IDs for many years (e.g., cellphones),
which resulted in support for such in RObust Header Compression
(ROHC) [RFC5225].
This document updates the specification of the IPv4 ID field to more
closely reflect current practice and to include considerations taken
into account during the specification of the similar field in IPv6.
2. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
In this document, the characters ">>" preceding one or more indented
lines indicate a requirement using the key words listed above. This
convention aids reviewers in quickly identifying or finding this
document's explicit requirements.
Touch Standards Track [Page 3]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
3. The IPv4 ID Field
IP supports datagram fragmentation, where large datagrams are split
into smaller components to traverse links with limited maximum
transmission units (MTUs). Fragments are indicated in different ways
in IPv4 and IPv6:
o In IPv4, fragments are indicated using four fields of the basic
header: Identification (ID), Fragment Offset, a "Don't Fragment"
(DF) flag, and a "More Fragments" (MF) flag [RFC791].
o In IPv6, fragments are indicated in an extension header that
includes an ID, Fragment Offset, and an M (more fragments) flag
similar to their counterparts in IPv4 [RFC2460].
IPv6 fragmentation differs from IPv4 fragmentation in a few important
ways. IPv6 fragmentation occurs only at the source, so a DF bit is
not needed to prevent downstream devices from initiating
fragmentation (i.e., IPv6 always acts as if DF=1). The IPv6 fragment
header is present only when a datagram has been fragmented, or when
the source has received a "packet too big" ICMPv6 error message
indicating that the path cannot support the required minimum
1280-byte IPv6 MTU and is thus subject to translation [RFC2460]
[RFC4443]. The latter case is relevant only for IPv6 datagrams sent
to IPv4 destinations to support subsequent fragmentation after
translation to IPv4.
With the exception of these two cases, the ID field is not present
for non-fragmented datagrams; thus, it is meaningful only for
datagrams that are already fragmented or datagrams intended to be
fragmented as part of IPv4 translation. Finally, the IPv6 ID field
is 32 bits and required unique per source/destination address pair
for IPv6, whereas for IPv4 it is only 16 bits and required unique per
source address/destination address/protocol tuple.
This document focuses on the IPv4 ID field issues, because in IPv6
the field is larger and present only in fragments.
3.1. Uses of the IPv4 ID Field
The IPv4 ID field was originally intended for fragmentation and
reassembly [RFC791]. Within a given source address, destination
address, and protocol, fragments of an original datagram are matched
based on their IPv4 ID. This requires that IDs be unique within the
source address/destination address/protocol tuple when fragmentation
is possible (e.g., DF=0) or when it has already occurred (e.g.,
frag_offset>0 or MF=1).
Touch Standards Track [Page 4]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
Other uses have been envisioned for the IPv4 ID field. The field has
been proposed as a way to detect and remove duplicate datagrams,
e.g., at congested routers (noted in Section 3.2.1.5 of [RFC1122]) or
in network accelerators. It has similarly been proposed for use at
end hosts to reduce the impact of duplication on higher-layer
protocols (e.g., additional processing in TCP or the need for
application-layer duplicate suppression in UDP). This is discussed
further in Section 5.1.
The IPv4 ID field is used in some diagnostic tools to correlate
datagrams measured at various locations along a network path. This
is already insufficient in IPv6 because unfragmented datagrams lack
an ID, so these tools are already being updated to avoid such
reliance on the ID field. This is also discussed further in
Section 5.1.
The ID clearly needs to be unique (within the MDL, within the source
address/destination address/protocol tuple) to support fragmentation
and reassembly, but not all datagrams are fragmented or allow
fragmentation. This document deprecates non-fragmentation uses,
allowing the ID to be repeated (within the MDL, within the source
address/destination address/protocol tuple) in those cases.
3.2. Background on IPv4 ID Reassembly Issues
The following is a summary of issues with IPv4 fragment reassembly in
high-speed environments raised previously [RFC4963]. Readers are
encouraged to consult RFC 4963 for a more detailed discussion of
these issues.
With the maximum IPv4 datagram size of 64 KB, a 16-bit ID field that
does not repeat within 120 seconds means that the aggregate of all
TCP connections of a given protocol between two IP endpoints is
limited to roughly 286 Mbps; at a more typical MTU of 1500 bytes,
this speed drops to 6.4 Mbps [RFC791] [RFC1122] [RFC4963]. This
limit currently applies for all IPv4 datagrams within a single
protocol (i.e., the IPv4 protocol field) between two IP addresses,
regardless of whether fragmentation is enabled or inhibited and
whether or not a datagram is fragmented.
IPv6, even at typical MTUs, is capable of 18.7 Tbps with
fragmentation between two IP endpoints as an aggregate across all
protocols, due to the larger 32-bit ID field (and the fact that the
IPv6 next-header field, the equivalent of the IPv4 protocol field, is
not considered in differentiating fragments). When fragmentation is
not used, the field is absent, and in that case IPv6 speeds are not
limited by the ID field uniqueness.
Touch Standards Track [Page 5]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
Note also that 120 seconds is only an estimate on the MDL. It is
related to the reassembly timeout as a lower bound and the TCP
Maximum Segment Lifetime as an upper bound (both as noted in
[RFC1122]). Network delays are incurred in other ways, e.g.,
satellite links, which can add seconds of delay even though the Time
to Live (TTL) is not decremented by a corresponding amount. There is
thus no enforcement mechanism to ensure that datagrams older than 120
seconds are discarded.
Wireless Internet devices are frequently connected at speeds over
54 Mbps, and wired links of 1 Gbps have been the default for several
years. Although many end-to-end transport paths are congestion
limited, these devices easily achieve 100+ Mbps application-layer
throughput over LANs (e.g., disk-to-disk file transfer rates), and
numerous throughput demonstrations with Commercial-Off-The-Shelf
(COTS) systems over wide-area paths have exhibited these speeds for
over a decade. This strongly suggests that IPv4 ID uniqueness has
been moot for a long time.
4. Updates to the IPv4 ID Specification
This document updates the specification of the IPv4 ID field in three
distinct ways, as discussed in subsequent subsections:
o Using the IPv4 ID field only for fragmentation
o Encouraging safe operation when the IPv4 ID field is used
o Avoiding a performance impact when the IPv4 ID field is used
There are two kinds of datagrams, which are defined below and used in
the following discussion:
o Atomic datagrams are datagrams not yet fragmented and for which
further fragmentation has been inhibited.
o Non-atomic datagrams are datagrams either that already have been
fragmented or for which fragmentation remains possible.
This same definition can be expressed in pseudo code, using common
logical operators (equals is ==, logical 'and' is &&, logical 'or' is
||, greater than is >, and the parenthesis function is used
typically) as follows:
o Atomic datagrams: (DF==1)&&(MF==0)&&(frag_offset==0)
o Non-atomic datagrams: (DF==0)||(MF==1)||(frag_offset>0)
Touch Standards Track [Page 6]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
The test for non-atomic datagrams is the logical negative of the test
for atomic datagrams; thus, all possibilities are considered.
4.1. IPv4 ID Used Only for Fragmentation
Although RFC 1122 suggests that the IPv4 ID field has other uses,
including datagram de-duplication, such uses are already not
interoperable with known implementations of sources that do not vary
their ID. This document thus defines this field's value only for
fragmentation and reassembly:
>> The IPv4 ID field MUST NOT be used for purposes other than
fragmentation and reassembly.
Datagram de-duplication can still be accomplished using hash-based
duplicate detection for cases where the ID field is absent (IPv6
unfragmented datagrams), which can also be applied to IPv4 atomic
datagrams without utilizing the ID field [RFC6621].
In atomic datagrams, the IPv4 ID field has no meaning; thus, it can
be set to an arbitrary value, i.e., the requirement for non-repeating
IDs within the source address/destination address/protocol tuple is
no longer required for atomic datagrams:
>> Originating sources MAY set the IPv4 ID field of atomic datagrams
to any value.
Second, all network nodes, whether at intermediate routers,
destination hosts, or other devices (e.g., NATs and other address-
sharing mechanisms, firewalls, tunnel egresses), cannot rely on the
field of atomic datagrams:
>> All devices that examine IPv4 headers MUST ignore the IPv4 ID
field of atomic datagrams.
The IPv4 ID field is thus meaningful only for non-atomic datagrams --
either those datagrams that have already been fragmented or those for
which fragmentation remains permitted. Atomic datagrams are detected
by their DF, MF, and fragmentation offset fields as explained in
Section 4, because such a test is completely backward compatible;
thus, this document does not reserve any IPv4 ID values, including 0,
as distinguished.
Deprecating the use of the IPv4 ID field for non-reassembly uses
should have little -- if any -- impact. IPv4 IDs are already
frequently repeated, e.g., over even moderately fast connections and
from some sources that do not vary the ID at all, and no adverse
impact has been observed. Duplicate suppression was suggested
Touch Standards Track [Page 7]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
[RFC1122] and has been implemented in some protocol accelerators, but
no impacts of IPv4 ID reuse have been noted to date. Routers are not
required to issue ICMPs on any particular timescale, and so IPv4 ID
repetition should not have been used for validation purposes; this
scenario has not been observed. Besides, repetition already occurs
and would have been noticed [RFC1812]. ICMP relaying at tunnel
ingresses is specified to use soft state rather than a datagram
cache; for similar reasons, if the latter is used, this should have
been noticed [RFC2003]. These and other legacy issues are discussed
further in Section 5.1.
4.2. Encouraging Safe IPv4 ID Use
This document also changes the specification of the IPv4 ID field to
encourage its safe use.
As discussed in RFC 1122, if TCP retransmits a segment, it may be
possible to reuse the IPv4 ID (see Section 6.2). This can make it
difficult for a source to avoid IPv4 ID repetition for received
fragments. RFC 1122 concludes that this behavior "is not useful";
this document formalizes that conclusion as follows:
>> The IPv4 ID of non-atomic datagrams MUST NOT be reused when
sending a copy of an earlier non-atomic datagram.
RFC 1122 also suggests that fragments can overlap. Such overlap can
occur if successive retransmissions are fragmented in different ways
but with the same reassembly IPv4 ID. This overlap is noted as the
result of reusing IPv4 IDs when retransmitting datagrams, which this
document deprecates. However, it is also the result of in-network
datagram duplication, which can still occur. As a result, this
document does not change the need for receivers to support
overlapping fragments.
4.3. IPv4 ID Requirements That Persist
This document does not relax the IPv4 ID field uniqueness
requirements of [RFC791] for non-atomic datagrams, that is:
>> Sources emitting non-atomic datagrams MUST NOT repeat IPv4 ID
values within one MDL for a given source address/destination
address/protocol tuple.
Such sources include originating hosts, tunnel ingresses, and NATs
(including other address-sharing mechanisms) (see Section 5.3).
Touch Standards Track [Page 8]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
This document does not relax the requirement that all network devices
honor the DF bit, that is:
>> IPv4 datagrams whose DF=1 MUST NOT be fragmented.
>> IPv4 datagram transit devices MUST NOT clear the DF bit.
Specifically, DF=1 prevents fragmenting atomic datagrams. DF=1 also
prevents further fragmenting received fragments. In-network
fragmentation is permitted only when DF=0; this document does not
change that requirement.
5. Impact of Proposed Changes
This section discusses the impact of the proposed changes on legacy
devices, datagram generation in updated devices, middleboxes, and
header compression.
5.1. Impact on Legacy Internet Devices
Legacy uses of the IPv4 ID field consist of fragment generation,
fragment reassembly, duplicate datagram detection, and "other" uses.
Current devices already generate ID values that are reused within the
source address/destination address/protocol tuple in less than the
current estimated Internet MDL of two minutes. They assume that the
MDL over their end-to-end path is much lower.
Existing devices have been known to generate non-varying IDs for
atomic datagrams for nearly a decade, notably some cellphones. Such
constant ID values are the reason for their support as an
optimization of ROHC [RFC5225]. This is discussed further in
Section 5.4. Generation of IPv4 datagrams with constant (zero) IDs
is also described as part of the IP/ICMP translation standard
[RFC6145].
Many current devices support fragmentation that ignores the IPv4
Don't Fragment (DF) bit. Such devices already transit traffic from
sources that reuse the ID. If fragments of different datagrams
reusing the same ID (within the source address/destination
address/protocol tuple) arrive at the destination interleaved,
fragmentation would fail and traffic would be dropped. Either such
interleaving is uncommon or traffic from such devices is not widely
traversing these DF-ignoring devices, because significant occurrence
of reassembly errors has not been reported. DF-ignoring devices do
not comply with existing standards, and it is not feasible to update
the standards to allow them as compliant.
Touch Standards Track [Page 9]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
The ID field has been envisioned for use in duplicate detection, as
discussed in Section 4.1. Although this document now allows IPv4 ID
reuse for atomic datagrams, such reuse is already common (as noted
above). Protocol accelerators are known to implement IPv4 duplicate
detection, but such devices are also known to violate other Internet
standards to achieve higher end-to-end performance. These devices
would already exhibit erroneous drops for this current traffic, and
this has not been reported.
There are other potential uses of the ID field, such as for
diagnostic purposes. Such uses already need to accommodate atomic
datagrams with reused ID fields. There are no reports of such uses
having problems with current datagrams that reuse IDs.
Thus, as a result of previous requirements, this document recommends
that IPv4 duplicate detection and diagnostic mechanisms apply
IPv6-compatible methods, i.e., methods that do not rely on the ID
field (e.g., as suggested in [RFC6621]). This is a consequence of
using the ID field only for reassembly, as well as the known hazard
of existing devices already reusing the ID field.
5.2. Impact on Datagram Generation
The following is a summary of the recommendations that are the result
of the previous changes to the IPv4 ID field specification.
Because atomic datagrams can use arbitrary IPv4 ID values, the ID
field no longer imposes a performance impact in those cases.
However, the performance impact remains for non-atomic datagrams. As
a result:
>> Sources of non-atomic IPv4 datagrams MUST rate-limit their output
to comply with the ID uniqueness requirements. Such sources
include, in particular, DNS over UDP [RFC2671].
Because there is no strict definition of the MDL, reassembly hazards
exist regardless of the IPv4 ID reuse interval or the reassembly
timeout. As a result:
>> Higher-layer protocols SHOULD verify the integrity of IPv4
datagrams, e.g., using a checksum or hash that can detect
reassembly errors (the UDP and TCP checksums are weak in this
regard, but better than nothing).
Additional integrity checks can be employed using tunnels, as
supported by the Subnetwork Encapsulation and Adaptation Layer (SEAL)
[RFC5320], IPsec [RFC4301], or the Stream Control Transmission
Protocol (SCTP) [RFC4960]. Such checks can avoid the reassembly
Touch Standards Track [Page 10]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
hazards that can occur when using UDP and TCP checksums [RFC4963] or
when using partial checksums as in UDP-Lite [RFC3828]. Because such
integrity checks can avoid the impact of reassembly errors:
>> Sources of non-atomic IPv4 datagrams using strong integrity checks
MAY reuse the ID within intervals that are smaller than typical
MDL values.
Note, however, that such frequent reuse can still result in corrupted
reassembly and poor throughput, although it would not propagate
reassembly errors to higher-layer protocols.
5.3. Impact on Middleboxes
Middleboxes include rewriting devices such as network address
translators (NATs), network address/port translators (NAPTs), and
other address-sharing mechanisms (ASMs). They also include devices
that inspect and filter datagrams but that are not routers, such as
accelerators and firewalls.
The changes proposed in this document may not be implemented by
middleboxes; however, these changes are more likely to make current
middlebox behavior compliant than to affect the service provided by
those devices.
5.3.1. Rewriting Middleboxes
NATs and NAPTs rewrite IP fields, and tunnel ingresses (using IPv4
encapsulation) copy and modify some IPv4 fields; all are therefore
considered datagram sources, as are any devices that rewrite any
portion of the source address/destination address/protocol/ID tuple
for any datagrams [RFC3022]. This is also true for other ASMs,
including IPv4 Residual Deployment (4rd) [De11], IVI [RFC6219], and
others in the "A+P" (address plus port) family [Bo11]. It is equally
true for any other datagram-rewriting mechanism. As a result, they
are subject to all the requirements of any datagram source, as has
been noted.
NATs/ASMs/rewriters present a particularly challenging situation for
fragmentation. Because they overwrite portions of the reassembly
tuple in both directions, they can destroy tuple uniqueness and
result in a reassembly hazard. Whenever IPv4 source address,
destination address, or protocol fields are modified, a
NAT/ASM/rewriter needs to ensure that the ID field is generated
appropriately, rather than simply copied from the incoming datagram.
Touch Standards Track [Page 11]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
Specifically:
>> Address-sharing or rewriting devices MUST ensure that the IPv4 ID
field of datagrams whose addresses or protocols are translated
comply with these requirements as if the datagram were sourced by
that device.
This compliance means that the IPv4 ID field of non-atomic datagrams
translated at a NAT/ASM/rewriter needs to obey the uniqueness
requirements of any IPv4 datagram source. Unfortunately, translated
fragments already violate that requirement, as they repeat an IPv4 ID
within the MDL for a given source address/destination
address/protocol tuple.
Such problems with transmitting fragments through NATs/ASMs/rewriters
are already known; translation is typically based on the transport
port number, which is present in only the first fragment anyway
[RFC3022]. This document underscores the point that not only is
reassembly (and possibly subsequent fragmentation) required for
translation, it can be used to avoid issues with IPv4 ID uniqueness.
Note that NATs/ASMs already need to exercise special care when
emitting datagrams on their public side, because merging datagrams
from many sources onto a single outgoing source address can result in
IPv4 ID collisions. This situation precedes this document and is not
affected by it. It is exacerbated in large-scale, so-called "carrier
grade" NATs [Pe11].
Tunnel ingresses act as sources for the outermost header, but tunnels
act as routers for the inner headers (i.e., the datagram as arriving
at the tunnel ingress). Ingresses can always fragment as originating
sources of the outer header, because they control the uniqueness of
that IPv4 ID field and the value of DF on the outer header
independent of those values on the inner (arriving datagram) header.
5.3.2. Filtering Middleboxes
Middleboxes also include devices that filter datagrams, such as
network accelerators and firewalls. Some such devices reportedly
feature datagram de-duplication that relies on IP ID uniqueness to
identify duplicates, which has been discussed in Section 5.1.
5.4. Impact on Header Compression
Header compression algorithms already accommodate various ways in
which the IPv4 ID changes between sequential datagrams [RFC1144]
[RFC2508] [RFC3545] [RFC5225]. Such algorithms currently assume that
the IPv4 ID is preserved end-to-end. Some algorithms already allow
Touch Standards Track [Page 12]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
the assumption that the ID does not change (e.g., ROHC [RFC5225]),
where others include non-changing IDs via zero deltas (e.g., Enhanced
Compressed RTP (ECRTP) [RFC3545]).
When compression assumes a changing ID as a default, having a
non-changing ID can make compression less efficient. Such
non-changing IDs have been described in various RFCs (e.g.,
footnote 21 of [RFC1144] and cRTP [RFC2508]). When compression
can assume a non-changing IPv4 ID -- as with ROHC and ECRTP --
efficiency can be increased.
5.5. Impact of Network Reordering and Loss
Tolerance to network reordering and loss is a key feature of the
Internet architecture. Although most current IP networks avoid
gratuitous such events, both reordering and loss can and do occur.
Datagrams are already intended to be reordered or lost, and recovery
from those errors (where supported) already occurs at the transport
or higher protocol layers.
Reordering is typically associated with routing transients or where
flows are split across multiple paths. Loss is typically associated
with path congestion or link failure (partial or complete). The
impact of such events is different for atomic and non-atomic
datagrams and is discussed below. In summary, the recommendations of
this document make the Internet more robust to reordering and loss by
emphasizing the requirements of ID uniqueness for non-atomic
datagrams and by more clearly indicating the impact of these
requirements on both endpoints and datagram transit devices.
5.5.1. Atomic Datagrams Experiencing Reordering or Loss
Reusing ID values does not affect atomic datagrams when the DF bit is
correctly respected, because order restoration does not depend on the
datagram header. TCP uses a transport header sequence number; in
some other protocols, sequence is indicated and restored at the
application layer.
When DF=1 is ignored, reordering or loss can cause fragments of
different datagrams to be interleaved and thus incorrectly
reassembled and discarded. Reuse of ID values in atomic datagrams,
as permitted by this document, can result in higher datagram loss in
such cases. Situations such as this already can exist because there
are known devices that use a constant ID for atomic datagrams (some
cellphones), and there are known devices that ignore DF=1, but high
levels of corresponding loss have not been reported. The lack of
such reports indicates either a lack of reordering or a loss in such
cases or a tolerance to the resulting losses. If such issues are
Touch Standards Track [Page 13]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
reported, it would be more productive to address non-compliant
devices (that ignore DF=1), because it is impractical to define
Internet specifications to tolerate devices that ignore those
specifications. This is why this document emphasizes the need to
honor DF=1, as well as that datagram transit devices need to retain
the DF bit as received (i.e., rather than clear it).
5.5.2. Non-atomic Datagrams Experiencing Reordering or Loss
Non-atomic datagrams rely on the uniqueness of the ID value to
tolerate reordering of fragments, notably where fragments of
different datagrams are interleaved as a result of such reordering.
Fragment loss can result in reassembly of fragments from different
origin datagrams, which is why ID reuse in non-atomic datagrams is
based on datagram (fragment) maximum lifetime, not just expected
reordering interleaving.
This document does not change the requirements for uniqueness of IDs
in non-atomic datagrams and thus does not affect their tolerance to
such reordering or loss. This document emphasizes the need for ID
uniqueness for all datagram sources, including rewriting middleboxes;
the need to rate-limit sources to ensure ID uniqueness; the need to
not reuse the ID for retransmitted datagrams; and the need to use
higher-layer integrity checks to prevent reassembly errors -- all of
which result in a higher tolerance to reordering or loss events.
6. Updates to Existing Standards
The following sections address the specific changes to existing
protocols indicated by this document.
6.1. Updates to RFC 791
RFC 791 states that:
The originating protocol module of an internet datagram sets the
identification field to a value that must be unique for that
source-destination pair and protocol for the time the datagram
will be active in the internet system.
It later states that:
Thus, the sender must choose the Identifier to be unique for this
source, destination pair and protocol for the time the datagram
(or any fragment of it) could be alive in the internet.
Touch Standards Track [Page 14]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
It seems then that a sending protocol module needs to keep a table
of Identifiers, one entry for each destination it has communicated
with in the last maximum datagram lifetime for the internet.
However, since the Identifier field allows 65,536 different
values, some host may be able to simply use unique identifiers
independent of destination.
It is appropriate for some higher level protocols to choose the
identifier. For example, TCP protocol modules may retransmit an
identical TCP segment, and the probability for correct reception
would be enhanced if the retransmission carried the same
identifier as the original transmission since fragments of either
datagram could be used to construct a correct TCP segment.
This document changes RFC 791 as follows:
o IPv4 ID uniqueness applies to only non-atomic datagrams.
o Retransmitted non-atomic IPv4 datagrams are no longer permitted to
reuse the ID value.
6.2. Updates to RFC 1122
RFC 1122 states in Section 3.2.1.5 ("Identification: RFC 791
Section 3.2") that:
When sending an identical copy of an earlier datagram, a host MAY
optionally retain the same Identification field in the copy.
DISCUSSION:
Some Internet protocol experts have maintained that when a
host sends an identical copy of an earlier datagram, the new
copy should contain the same Identification value as the
original. There are two suggested advantages: (1) if the
datagrams are fragmented and some of the fragments are lost,
the receiver may be able to reconstruct a complete datagram
from fragments of the original and the copies; (2) a
congested gateway might use the IP Identification field (and
Fragment Offset) to discard duplicate datagrams from the
queue.
Touch Standards Track [Page 15]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
This document changes RFC 1122 as follows:
o The IPv4 ID field is no longer permitted to be used for duplicate
detection. This applies to both atomic and non-atomic datagrams.
o Retransmitted non-atomic IPv4 datagrams are no longer permitted to
reuse the ID value.
6.3. Updates to RFC 2003
This document updates how IPv4-in-IPv4 tunnels create IPv4 ID values
for the IPv4 outer header [RFC2003], but only in the same way as for
any other IPv4 datagram source. Specifically, RFC 2003 states the
following, where [10] refers to RFC 791:
Identification, Flags, Fragment Offset
These three fields are set as specified in [10]...
This document changes RFC 2003 as follows:
o The IPv4 ID field is set as permitted by RFC 6864.
7. Security Considerations
When the IPv4 ID is ignored on receipt (e.g., for atomic datagrams),
its value becomes unconstrained; therefore, that field can more
easily be used as a covert channel. For some atomic datagrams it is
now possible, and may be desirable, to rewrite the IPv4 ID field to
avoid its use as such a channel. Rewriting would be prohibited for
datagrams protected by the IPsec Authentication Header (AH), although
we do not recommend use of the AH to achieve this result [RFC4302].
The IPv4 ID also now adds much less to the entropy of the header of a
datagram. Such entropy might be used as input to cryptographic
algorithms or pseudorandom generators, although IDs have never been
assured sufficient entropy for such purposes. The IPv4 ID had
previously been unique (for a given source/address pair, and protocol
field) within one MDL, although this requirement was not enforced and
clearly is typically ignored. The IPv4 ID of atomic datagrams is not
required unique and so contributes no entropy to the header.
The deprecation of the IPv4 ID field's uniqueness for atomic
datagrams can defeat the ability to count devices behind a
NAT/ASM/rewriter [Be02]. This is not intended as a security feature,
however.
Touch Standards Track [Page 16]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
8. References
8.1. Normative References
[RFC791] Postel, J., "Internet Protocol", STD 5, RFC 791,
September 1981.
[RFC1122] Braden, R., Ed., "Requirements for Internet Hosts -
Communication Layers", STD 3, RFC 1122, October 1989.
[RFC1812] Baker, F., Ed., "Requirements for IP Version 4 Routers",
RFC 1812, June 1995.
[RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003,
October 1996.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
8.2. Informative References
[Be02] Bellovin, S., "A Technique for Counting NATted Hosts",
Internet Measurement Conference, Proceedings of the 2nd
ACM SIGCOMM Workshop on Internet Measurement,
November 2002.
[Bo11] Boucadair, M., Touch, J., Levis, P., and R. Penno,
"Analysis of Solution Candidates to Reveal a Host
Identifier in Shared Address Deployments", Work in
Progress, September 2011.
[De11] Despres, R., Ed., Matsushima, S., Murakami, T., and O.
Troan, "IPv4 Residual Deployment across IPv6-Service
networks (4rd) ISP-NAT's made optional", Work in Progress,
March 2011.
[Pe11] Perreault, S., Ed., Yamagata, I., Miyakawa, S., Nakagawa,
A., and H. Ashida, "Common requirements for Carrier Grade
NATs (CGNs)", Work in Progress, December 2012.
[RFC1144] Jacobson, V., "Compressing TCP/IP Headers for Low-Speed
Serial Links", RFC 1144, February 1990.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, December 1998.
Touch Standards Track [Page 17]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
[RFC2508] Casner, S. and V. Jacobson, "Compressing IP/UDP/RTP
Headers for Low-Speed Serial Links", RFC 2508,
February 1999.
[RFC2671] Vixie, P., "Extension Mechanisms for DNS (EDNS0)",
RFC 2671, August 1999.
[RFC3022] Srisuresh, P. and K. Egevang, "Traditional IP Network
Address Translator (Traditional NAT)", RFC 3022,
January 2001.
[RFC3545] Koren, T., Casner, S., Geevarghese, J., Thompson, B., and
P. Ruddy, "Enhanced Compressed RTP (CRTP) for Links with
High Delay, Packet Loss and Reordering", RFC 3545,
July 2003.
[RFC3828] Larzon, L-A., Degermark, M., Pink, S., Jonsson, L-E., Ed.,
and G. Fairhurst, Ed., "The Lightweight User Datagram
Protocol (UDP-Lite)", RFC 3828, July 2004.
[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, December 2005.
[RFC4302] Kent, S., "IP Authentication Header", RFC 4302,
December 2005.
[RFC4443] Conta, A., Deering, S., and M. Gupta, Ed., "Internet
Control Message Protocol (ICMPv6) for the Internet
Protocol Version 6 (IPv6) Specification", RFC 4443,
March 2006.
[RFC4960] Stewart, R., Ed., "Stream Control Transmission Protocol",
RFC 4960, September 2007.
[RFC4963] Heffner, J., Mathis, M., and B. Chandler, "IPv4 Reassembly
Errors at High Data Rates", RFC 4963, July 2007.
[RFC5225] Pelletier, G. and K. Sandlund, "RObust Header Compression
Version 2 (ROHCv2): Profiles for RTP, UDP, IP, ESP and
UDP-Lite", RFC 5225, April 2008.
[RFC5320] Templin, F., Ed., "The Subnetwork Encapsulation and
Adaptation Layer (SEAL)", RFC 5320, February 2010.
[RFC6145] Li, X., Bao, C., and F. Baker, "IP/ICMP Translation
Algorithm", RFC 6145, April 2011.
Touch Standards Track [Page 18]
RFC 6864 Updated Spec. of the IPv4 ID Field February 2013
[RFC6219] Li, X., Bao, C., Chen, M., Zhang, H., and J. Wu, "The
China Education and Research Network (CERNET) IVI
Translation Design and Deployment for the IPv4/IPv6
Coexistence and Transition", RFC 6219, May 2011.
[RFC6621] Macker, J., Ed., "Simplified Multicast Forwarding",
RFC 6621, May 2012.
9. Acknowledgments
This document was inspired by numerous discussions with the author by
Jari Arkko, Lars Eggert, Dino Farinacci, and Fred Templin, as well as
members participating in the Internet Area Working Group. Detailed
feedback was provided by Gorry Fairhurst, Brian Haberman, Ted Hardie,
Mike Heard, Erik Nordmark, Carlos Pignataro, and Dan Wing. This
document originated as an Independent Submissions stream document
co-authored by Matt Mathis, PSC, and his contributions are greatly
appreciated.
This document was initially prepared using 2-Word-v2.0.template.dot.
Author's Address
Joe Touch
USC/ISI
4676 Admiralty Way
Marina del Rey, CA 90292-6695
U.S.A.
Phone: +1 (310) 448-9151
EMail: touch@isi.edu
Touch Standards Track [Page 19]