Keywords: [--------|], pw operation, PW-MPLS-STD-MIB
Network Working Group D. Zelig, Ed.
Request for Comments: 5602 Oversi
Category: Standards Track T. Nadeau, Ed.
BT
July 2009
Pseudowire (PW) over MPLS PSN Management Information Base (MIB)
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes a MIB module for PW operation over
Multiprotocol Label Switching (MPLS) Label Switching Routers (LSRs).
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Zelig & Nadeau Standards Track [Page 1]
RFC 5602 PW MPLS MIB July 2009
Table of Contents
1. Introduction ....................................................2
2. The Internet-Standard Management Framework ......................2
3. Terminology .....................................................3
4. Overview ........................................................3
5. Features Checklist ..............................................4
6. MIB Module Usage ................................................5
7. PW-MPLS-STD-MIB Example .........................................7
8. Object Definitions ..............................................8
9. Security Considerations ........................................28
10. IANA Considerations ...........................................29
11. References ....................................................29
11.1. Normative References .....................................29
11.2. Informative References ...................................30
1. Introduction
This document describes a model for managing pseudowire services for
transmission over different flavors of MPLS tunnels. The general PW
MIB module [RFC5601] defines the parameters global to the PW
regardless of the underlying Packet Switched Network (PSN) and
emulated service. This document is applicable for PWs that use MPLS
PSN type in the PW-STD-MIB.
This document describes the MIB objects that define pseudowire
association to the MPLS PSN, in a way that is not specific to the
carried service.
Together, [RFC3811] and [RFC3812] describe the modeling of an MPLS
tunnel, and a tunnel's underlying cross-connects. This MIB module
supports MPLS-TE PSN, non-TE MPLS PSN (an outer tunnel created by the
Label Distribution Protocol (LDP) or manually), and MPLS PW label
only (no outer tunnel).
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
Zelig & Nadeau Standards Track [Page 2]
RFC 5602 PW MPLS MIB July 2009
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
3. Terminology
This document uses terminology from the document describing the PW
architecture [RFC3985], [RFC3916], and [RFC4447].
The terms "outbound" and "inbound" in this MIB module are based on
the common practice in the MPLS standards; i.e. "outbound" is toward
the PSN. However, where these terms are used in an object name, the
object description clarifies the exact packet direction to prevent
confusion with these terms in other documents.
"PSN tunnel" is a general term indicating a virtual connection
between the two Pseudowire Emulation Edge-to-Edge (PWE3) edge
devices. Each tunnel may potentially carry multiple PWs inside. An
MPLS tunnel is within the scope of this document.
This document uses terminology from the document describing the MPLS
architecture [RFC3031] for MPLS PSN. A Label Switched Path (LSP) is
modeled as described in [RFC3811] and [RFC3812] via a series of
cross-connects through one or more Label Switching Routers (LSRs).
In MPLS PSN, a PW connection typically uses a PW label within a
tunnel label [RFC4447]. Multiple pseudowires each with a unique PW
label can share the same tunnel. For PW transport over MPLS, the
tunnel label is known as the "outer" label, while the PW label is
known as the "inner" label. An exception to this is with adjacent
LSRs or the use of a Penultimate Hop Popping (PHP). In this case,
there is an option for PWs to connect directly without an outer
label.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [BCP14].
4. Overview
The MIB module structure for defining a PW service consists of three
layers of MIB modules functioning together. This general model is
defined in the PWE3 architecture [RFC3985]. The layering model is
intended to sufficiently isolate PW services from the underlying PSN
layer that carries the emulated service. This is done at the same
time as providing a standard means for connecting any supported
services to any supported PSNs.
Zelig & Nadeau Standards Track [Page 3]
RFC 5602 PW MPLS MIB July 2009
The first layer, known as the service layer, contains service-
specific modules. These modules define service-specific management
objects that interface or collaborate with existing MIB modules for
the native version of the service. The service-specific module
"glues" the standard modules to the PWE3 MIB modules.
The next layer of the PWE3 MIB structure is the PW MIB module
[RFC5601]. This module is used to configure general parameters of
PWs that are common to all types of emulated services and PSNs. This
layer is connected to the service-specific layer above and the PSN
layer below.
The PSN layer provides PSN-specific modules for each type of PSN.
These modules associate the PW with one or more "tunnels" that carry
the service over the PSN. These modules are used to "glue" the PW
service to the underlying PSN-specific MIB modules. This document
defines the MIB module for PW over MPLS PSN.
[RFC5542] defines some of the object types used in these modules.
5. Features Checklist
The PW-MPLS-STD-MIB module is designed to satisfy the following
requirements and constraints:
- The MIB module supports both manually configured and signaled PWs.
- The MIB module supports point-to-point PW connections.
- The MIB module enables the use of any emulated service.
- The MIB module supports MPLS-TE outer tunnel, non-TE MPLS outer
tunnel (an outer tunnel signaled by LDP or set up manually), and
no outer tunnel (where the PW label is the only label in the MPLS
stack). The latter case is applicable for manual configuration of
PW over a single hop, as for signaled MPLS PSN even across a
single hop there is an MPLS tunnel -- even though the actual
packet may not contain the MPLS tunnel label due to PHP.
The MIB module uses Textual Conventions (TCs) from [RFC2578],
[RFC2579], [RFC2580], [RFC2863], [RFC3811], [RFC3813], [RFC5542], and
[RFC5601].
Zelig & Nadeau Standards Track [Page 4]
RFC 5602 PW MPLS MIB July 2009
6. MIB Module Usage
- The PW table (pwTable) in [RFC5601] is used for all PW types (ATM,
FR, Ethernet, SONET, etc.). This table contains high-level
generic parameters related to the PW creation. The operator or
the agent creates a row for each PW.
- If the selected PSN type in the pwTable is MPLS, the agent creates
a row in the MPLS-specific parameters table (pwMplsTable) in this
module, which contains MPLS-specific parameters such as EXP bits
handling and outer tunnel configuration.
- The operator configures the association to the desired MPLS tunnel
(required for MPLS-TE tunnels or for manually configured PWs)
through the pwMplsTeOutboundTable. For the LDP-based outer
tunnel, there is no need for manual configuration since there is
only a single tunnel toward the peer.
- The agent creates rows in the MPLS mapping table in order to allow
quick retrieval of information based on the tunnel indexes.
The relation to the MPLS network is by configuration of the edge LSR
only -- i.e., the LSR that provides the PW function. Since tunnels
are unidirectional, a pair of tunnels MUST exist (one for inbound,
one for outbound). Figure 1 depicts a PW that originates and
terminates at LSR-M. It uses tunnels A and B formed by cross-
connects (XCs) Ax and Bx continuing through LSR-N to LSR-P. The
concatenations of XCs create the tunnels. Note: 'X' denotes a
tunnel's cross-connect.
Zelig & Nadeau Standards Track [Page 5]
RFC 5602 PW MPLS MIB July 2009
Tunnel A
<- - - - - - - - - - - - - - - - - - - - - - - - - - - -
+---- (edge) LSR-M ---+ +--------- LSR-N ---------+ + LSR-P
|---+ | | | |
| | XC | | XC | |
+ | A1 (M<-N) +----+ +----+ A2 (M<-P) +----+ +----+
| | <------| | | |<--------------| | | |
<-->| N |PWin inSeg |MPLS| |MPLS| outSeg inSeg |MPLS| |MPLS|
N S | | <---X<-----| IF | | IF |<------X<------| IF | | IF |
A E | S | | |<-->| | | |<-->| | |
T R | | --->X----->| | | |------>X------>| | | |
I V | P |PWout outSeg| | | | inSeg outSeg | | | |
V I | | ------>| | | |-------------->| | | |
E C + | XC +----+ +----+ XC +----+ +----+
E |---+ B1 (M->N) | | B2 (M->P) | |
| | | | |
+---------------------+ +-------------------------+ +-----
- - - - - - - - - - - - - - - - - - - - - - - - - - - ->
Tunnel B
Figure 1: PW modeling over MPLS
The PW-MPLS-STD-MIB supports three options for an MPLS network:
(1) In the MPLS-TE case, tunnels A and B are created via the MPLS-
TE-STD-MIB [RFC3812]. The tunnels are associated (in each peer
independently) to the PW by the four indexes that uniquely
identify the tunnel at the MPLS-TE-STD-MIB.
(2) In the non-TE case, tunnels A1 and B1 are either manually
configured or set up with LDP. The tunnels are associated to
the PW by the XC index in the MPLS-LSR-STD-MIB [RFC3813].
(3) In the PW-label-only case, there is no outer tunnel on top of
the PW label. This case is useful in the case of adjacent
Provider Edges (PEs) in manual configuration mode. Note that
for signaled tunnels, when LSR-N acts as PHP for the outer
tunnel label, there are still entries for the outer tunnel in
the relevant MPLS MIB modules, so even for the case of adjacent
LSRs, the relevant mode is either MPLS-TE or non-TE.
A combination of MPLS-TE outer tunnel(s) and LDP outer tunnel for the
same PW is allowed through the pwMplsOutboundTunnel. The current
tunnel that is used to forward traffic is indicated in the object
pwMplsOutboundTunnelTypeInUse.
Zelig & Nadeau Standards Track [Page 6]
RFC 5602 PW MPLS MIB July 2009
The PW-MPLS-STD-MIB module reports through the inbound table the XC
entry in the LDP-STD-MIB [RFC3815] of the PW that was signaled
through LDP.
This MIB module assumes that a PW can be associated to one MPLS-TE
tunnel at a time. This tunnel may be composed of multiple instances
(i.e., LSP), each represented by a separate instance index. The
selection of the active LSP out of the possible LSPs in the tunnel is
out of the scope of this MIB module as it is part of the MPLS PSN
functionality. The current active LSP is reported through this MIB
module.
It is important to note that inbound (tunnel originated in the remote
PE) mapping is not configured or reported through the PW-MPLS-STD-
MIB module since the local PE does not know the inbound association
between specific PW and MPLS tunnels.
7. PW-MPLS-STD-MIB Example
The following example (supplement the example provided in [RFC5601])
assumes that the node has already established the LDP tunnel to the
peer node and that a PW has been configured in the pwTable in
[RFC5601] with pwPsnType equal 'mpls'.
The agent creates an entry in pwMplsTable with the following
parameters:
pwMplsMplsType mplsNonTe(1), -- LDP tunnel
pwMplsExpBitsMode outerTunnel(1), -- Default
pwMplsExpBits 0, -- Default
pwMplsTtl 2, -- Default
pwMplsLocalLdpID 192.0.2.200:0,
pwMplsLocalLdpEntityIndex 1,
pwMplsPeerLdpID 192.0.2.5:0,
pwMplsStorageType nonVolatile(3)
The agent also creates an entry in pwMplsOutboundTable for reporting
the mapping of the PW on the LDP tunnel:
pwMplsOutboundLsrXcIndex 100, - The XC number for the
-- LDP tunnel
pwMplsOutboundTunnelIndex 0, -- No TE tunnel
pwMplsOutboundTunnelInstance 0, -- No TE tunnel
pwMplsOutboundTunnelLclLSR 0, -- No TE tunnel
pwMplsOutboundTunnelPeerLSR 0, -- No TE tunnel
pwMplsOutboundIfIndex 0, -- Not applicable
pwMplsOutboundTunnelTypeInUse mplsNonTe(3)
Zelig & Nadeau Standards Track [Page 7]
RFC 5602 PW MPLS MIB July 2009
The agent now creates entries for the PW in the following
tables:
- pwMplsInboundTable
- pwMplsNonTeMappingTable (2 entries)
To create an MPLS-TE tunnel to carry this PW, the operator
takes the following steps:
- Set pwMplsMplsType in pwMplsTable to both mplsNonTe(1) and
mplsTe(0).
- Set pwMplsOutboundTunnelIndex, pwMplsOutboundTunnelInstance,
pwMplsOutboundTunnelLclLSR, and pwMplsOutboundTunnelPeerLSR in
pwMplsOutboundTable to the MPLS-TE tunnel that will carry this PW.
The agent will report the tunnel that the PW is currently using
through pwMplsOutboundTunnelTypeInUse, and will report the PW to
MPLS-TE tunnel/LSP mapping in pwMplsTeMappingTable.
8. Object Definitions
PW-MPLS-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, mib-2
FROM SNMPv2-SMI -- [RFC2578]
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF -- [RFC2580]
StorageType
FROM SNMPv2-TC -- [RFC2579]
InterfaceIndexOrZero
FROM IF-MIB -- [RFC2863]
MplsTunnelIndex, MplsTunnelInstanceIndex,
MplsLdpIdentifier, MplsLsrIdentifier
FROM MPLS-TC-STD-MIB -- [RFC3811]
MplsIndexType
FROM MPLS-LSR-STD-MIB -- [RFC3813]
PwIndexType
FROM PW-TC-STD-MIB -- [RFC5542]
Zelig & Nadeau Standards Track [Page 8]
RFC 5602 PW MPLS MIB July 2009
pwIndex -- [RFC5601]
FROM PW-STD-MIB
;
pwMplsStdMIB MODULE-IDENTITY
LAST-UPDATED "200906120000Z" -- 12 June 2009 00:00:00 GMT
ORGANIZATION "Pseudowire Emulation Edge-to-Edge (PWE3) Working
Group."
CONTACT-INFO
"
David Zelig, Editor
Email: davidz@corrigent.com
Thomas D. Nadeau, Editor
Email: tom.nadeau@bt.com
The PWE3 Working Group (email distribution pwe3@ietf.org,
http://www.ietf.org/html.charters/pwe3-charter.html)
"
DESCRIPTION
"This MIB module complements the PW-STD-MIB module for PW
operation over MPLS.
Copyright (c) 2009 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
- Redistributions of source code must retain the above
copyright notice, this list of conditions and the
following disclaimer.
- Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
- Neither the name of Internet Society, IETF or IETF Trust,
nor the names of specific contributors, may be used to
endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
Zelig & Nadeau Standards Track [Page 9]
RFC 5602 PW MPLS MIB July 2009
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This version of this MIB module is part of RFC 5602;
see the RFC itself for full legal notices.
"
-- Revision history.
REVISION "200906120000Z" -- 12 June 2009 00:00:00 GMT
DESCRIPTION
"First published as RFC 5602. "
::= { mib-2 181 }
-- Top-level components of this MIB.
-- Notifications
pwMplsNotifications OBJECT IDENTIFIER
::= { pwMplsStdMIB 0 }
-- Tables, Scalars
pwMplsObjects OBJECT IDENTIFIER
::= { pwMplsStdMIB 1 }
-- Conformance
pwMplsConformance OBJECT IDENTIFIER
::= { pwMplsStdMIB 2 }
-- PW MPLS table
pwMplsTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwMplsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table controls MPLS-specific parameters when the PW is
going to be carried over MPLS PSN."
::= { pwMplsObjects 1 }
pwMplsEntry OBJECT-TYPE
SYNTAX PwMplsEntry
MAX-ACCESS not-accessible
Zelig & Nadeau Standards Track [Page 10]
RFC 5602 PW MPLS MIB July 2009
STATUS current
DESCRIPTION
"A row in this table represents parameters specific to MPLS
PSN for a pseudowire (PW). The row is created
automatically by the local agent if the pwPsnType is
mpls(1). It is indexed by pwIndex, which uniquely
identifies a singular PW.
Manual entries in this table SHOULD be preserved after a
reboot, and the agent MUST ensure the integrity of those
entries.
If the set of entries of a specific row were found to be
nonconsistent after reboot, the PW pwOperStatus MUST be
declared as down(2).
Any read-write object in this table MAY be changed at any
time; however, change of some objects (for example,
pwMplsMplsType) during PW forwarding state MAY cause traffic
disruption."
INDEX { pwIndex }
::= { pwMplsTable 1 }
PwMplsEntry ::= SEQUENCE {
pwMplsMplsType BITS,
pwMplsExpBitsMode INTEGER,
pwMplsExpBits Unsigned32,
pwMplsTtl Unsigned32,
pwMplsLocalLdpID MplsLdpIdentifier,
pwMplsLocalLdpEntityIndex Unsigned32,
pwMplsPeerLdpID MplsLdpIdentifier,
pwMplsStorageType StorageType
}
pwMplsMplsType OBJECT-TYPE
SYNTAX BITS {
mplsTe (0),
mplsNonTe (1),
pwOnly (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is set by the operator to indicate the outer
tunnel types, if existing. mplsTe(0) is used if the outer
tunnel is set up by MPLS-TE, and mplsNonTe(1) is used if the
outer tunnel is set up by LDP or manually. A combination of
mplsTe(0) and mplsNonTe(1) MAY exist.
pwOnly(2) is used if there is no outer tunnel label, i.e.,
Zelig & Nadeau Standards Track [Page 11]
RFC 5602 PW MPLS MIB July 2009
in static provisioning without an MPLS tunnel. pwOnly(2)
cannot be combined with mplsNonTe(1) or mplsTe(0).
An implementation that can identify automatically that the
peer node is directly connected MAY support the bit
pwOnly(2) as read-only.
"
DEFVAL { { mplsNonTe } }
::= { pwMplsEntry 1 }
pwMplsExpBitsMode OBJECT-TYPE
SYNTAX INTEGER {
outerTunnel (1),
specifiedValue (2),
serviceDependant (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is set by the operator to determine the PW shim
label EXP bits. The value of outerTunnel(1) is used where
there is an outer tunnel -- pwMplsMplsType equals to
mplsTe(0) or mplsNonTe(1). Note that in this case, there
is no need to mark the PW label with the EXP bits, since the
PW label is not visible to the intermediate nodes.
If there is no outer tunnel, specifiedValue(2) SHOULD be used
to indicate that the value is specified by pwMplsExpBits.
Setting serviceDependant(3) indicates that the EXP bits are
set based on a rule that is implementation specific."
DEFVAL { outerTunnel }
::= { pwMplsEntry 2 }
pwMplsExpBits OBJECT-TYPE
SYNTAX Unsigned32 (0..7)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is set by the operator if pwMplsExpBitsMode is
set to specifiedValue(2) to indicate the MPLS EXP bits to
be used on the PW shim label. Otherwise, it SHOULD be set
to zero."
DEFVAL { 0 }
::= { pwMplsEntry 3 }
pwMplsTtl OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
Zelig & Nadeau Standards Track [Page 12]
RFC 5602 PW MPLS MIB July 2009
STATUS current
DESCRIPTION
"This object is set by the operator to indicate the PW TTL
value to be used on the PW shim label."
DEFVAL { 2 }
::= { pwMplsEntry 4 }
pwMplsLocalLdpID OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The LDP identifier of the LDP entity that creates
this PW in the local node. As the PW labels are always
set from the per-platform label space, the last two octets
in the LDP ID MUST always both be zeros."
REFERENCE
"'LDP specifications', RFC 3036, section 2.2.2."
::= { pwMplsEntry 5 }
pwMplsLocalLdpEntityIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The local node LDP Entity Index of the LDP entity creating
this PW."
::= { pwMplsEntry 6 }
pwMplsPeerLdpID OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The peer LDP identifier of the LDP session. This object
SHOULD return the value zero if LDP is not used or if the
value is not yet known."
::= { pwMplsEntry 7 }
pwMplsStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable indicates the storage type for this row."
DEFVAL { nonVolatile }
::= { pwMplsEntry 8 }
Zelig & Nadeau Standards Track [Page 13]
RFC 5602 PW MPLS MIB July 2009
-- End of PW MPLS Table
-- Pseudowire MPLS Outbound Tunnel Table
pwMplsOutboundTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwMplsOutboundEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table reports and configures the current outbound MPLS
tunnels (i.e., toward the PSN) or the physical interface in
the case of a PW label only that carries the PW traffic. It
also reports the current outer tunnel and LSP that forward
the PW traffic."
::= { pwMplsObjects 2 }
pwMplsOutboundEntry OBJECT-TYPE
SYNTAX PwMplsOutboundEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table configures the outer tunnel used for
carrying the PW traffic toward the PSN.
In the case of PW label only, it configures the interface
that will carry the PW traffic.
An entry in this table augments the pwMplsEntry, and is
created automatically when the corresponding row has been
created by the agent in the pwMplsEntry.
This table points to the appropriate MPLS MIB module:
In the MPLS-TE case, the three objects relevant to the
indexing of a TE tunnel head-end (as used in the
MPLS-TE-STD-MIB) are to be configured, and the tunnel
instance indicates the LSP that is currently in use for
forwarding the traffic.
In the case of signaled non-TE MPLS (an outer tunnel label
assigned by LDP), the table points to the XC entry in the
LSR-STD-MIB. If the non-TE MPLS tunnel is manually
configured, the operator configures the XC pointer to this
tunnel.
In the case of PW label only (no outer tunnel), the ifIndex
of the port to carry the PW is configured here.
Zelig & Nadeau Standards Track [Page 14]
RFC 5602 PW MPLS MIB July 2009
It is possible to associate a PW to one TE tunnel head-end
and a non-TE tunnel together. An indication in this table
will report the currently active one. In addition, in the
TE case, the table reports the active tunnel instance
(i.e., the specific LSP in use).
Any read-write object in this table MAY be changed at any
time; however, change of some objects (for example,
MPLS-TE indexes) during PW forwarding state MAY cause traffic
disruption."
AUGMENTS { pwMplsEntry }
::= { pwMplsOutboundTable 1 }
PwMplsOutboundEntry ::= SEQUENCE {
pwMplsOutboundLsrXcIndex MplsIndexType,
pwMplsOutboundTunnelIndex MplsTunnelIndex,
pwMplsOutboundTunnelInstance MplsTunnelInstanceIndex,
pwMplsOutboundTunnelLclLSR MplsLsrIdentifier,
pwMplsOutboundTunnelPeerLSR MplsLsrIdentifier,
pwMplsOutboundIfIndex InterfaceIndexOrZero,
pwMplsOutboundTunnelTypeInUse INTEGER
}
pwMplsOutboundLsrXcIndex OBJECT-TYPE
SYNTAX MplsIndexType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is applicable if the pwMplsMplsType mplsNonTe(1)
bit is set, and MUST return a value of zero otherwise.
If the outer tunnel is signaled, the object is read-only
and indicates the XC index in the MPLS-LSR-STD-MIB of the
outer tunnel toward the peer. Otherwise (tunnel is set up
manually), the operator defines the XC index of the manually
created outer tunnel through this object.
"
::= { pwMplsOutboundEntry 1 }
pwMplsOutboundTunnelIndex OBJECT-TYPE
SYNTAX MplsTunnelIndex
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is applicable if the pwMplsMplsType mplsTe(0)
bit is set, and MUST return a value of zero otherwise.
It is part of the set of indexes for the outbound tunnel.
Zelig & Nadeau Standards Track [Page 15]
RFC 5602 PW MPLS MIB July 2009
The operator sets this object to represent the desired
tunnel head-end toward the peer for carrying the PW
traffic.
"
::= { pwMplsOutboundEntry 2 }
pwMplsOutboundTunnelInstance OBJECT-TYPE
SYNTAX MplsTunnelInstanceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is applicable if the pwMplsMplsType mplsTe(0)
bit is set, and MUST return a value of zero otherwise.
It indicates the actual tunnel instance that is currently
active and carrying the PW traffic. It SHOULD return the
value zero if the information from the MPLS-TE
application is not yet known.
"
::= { pwMplsOutboundEntry 3 }
pwMplsOutboundTunnelLclLSR OBJECT-TYPE
SYNTAX MplsLsrIdentifier
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is applicable if the pwMplsMplsType mplsTe(0)
bit is set, and MUST return a value of all zeros otherwise.
It is part of the set of indexes for the outbound tunnel.
The operator sets this object to represent the desired
tunnel head-end toward the peer for carrying the PW
traffic.
"
::= { pwMplsOutboundEntry 4 }
pwMplsOutboundTunnelPeerLSR OBJECT-TYPE
SYNTAX MplsLsrIdentifier
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is applicable if the pwMplsMplsType mplsTe(0)
bit is set, and MUST return a value of zero otherwise.
It is part of the set of indexes for the outbound tunnel.
Note that in most cases, it equals to pwPeerAddr.
"
::= { pwMplsOutboundEntry 5 }
pwMplsOutboundIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
Zelig & Nadeau Standards Track [Page 16]
RFC 5602 PW MPLS MIB July 2009
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is applicable if the pwMplsMplsType pwOnly(0)
bit is set, and MUST return a value of zero otherwise.
The operator configures the ifIndex of the outbound port
in this case.
"
::= { pwMplsOutboundEntry 6 }
pwMplsOutboundTunnelTypeInUse OBJECT-TYPE
SYNTAX INTEGER {
notYetKnown (1),
mplsTe (2),
mplsNonTe (3),
pwOnly (4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the current tunnel that is carrying
the PW traffic.
The value of notYetKnown(1) should be used if the agent is
currently unable to determine which tunnel or interface is
carrying the PW, for example, because both tunnels are in
operational status down.
"
::= { pwMplsOutboundEntry 7 }
-- End of PW MPLS Outbound Tunnel table
-- PW MPLS inbound table
pwMplsInboundTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwMplsInboundEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table indicates the PW LDP XC entry in the
MPLS-LSR-STD-MIB for signaled PWs.
"
::= { pwMplsObjects 3 }
pwMplsInboundEntry OBJECT-TYPE
SYNTAX PwMplsInboundEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Zelig & Nadeau Standards Track [Page 17]
RFC 5602 PW MPLS MIB July 2009
"A row in this table is created by the agent
for each signaled PW, and shows the XC index related to
the PW signaling in the inbound direction in the
MPLS-LSR-STD-MIB that controls and display the information
for all the LDP signaling processes in the local node.
"
INDEX { pwIndex }
::= { pwMplsInboundTable 1 }
PwMplsInboundEntry ::= SEQUENCE {
pwMplsInboundXcIndex MplsIndexType
}
pwMplsInboundXcIndex OBJECT-TYPE
SYNTAX MplsIndexType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The XC index representing this PW in the inbound
direction. It MUST return the value zero if the
information is not yet known."
::= { pwMplsInboundEntry 1 }
-- End of PW MPLS inbound table
-- PW to Non-TE mapping Table.
pwMplsNonTeMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwMplsNonTeMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table indicates the PW association to the outbound
tunnel in non-TE applications, maps the PW to its (inbound)
XC entry, and indicates the PW-to-physical interface mapping
for a PW without an outer tunnel.
"
::= { pwMplsObjects 4 }
pwMplsNonTeMappingEntry OBJECT-TYPE
SYNTAX PwMplsNonTeMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table displays the association
between the PW and
- its non-TE MPLS outbound outer tunnel,
Zelig & Nadeau Standards Track [Page 18]
RFC 5602 PW MPLS MIB July 2009
- its XC entry in the MPLS-LSR-STD-MIB, or
- its physical interface if there is no outer tunnel
(PW label only) and manual configuration.
Rows are created in this table by the agent depending on
the setting of pwMplsMplsType:
- If the pwMplsMplsType mplsNonTe(1) bit is set, the agent
creates a row for the outbound direction
(pwMplsNonTeMappingDirection set to psnBound(1)).
The pwMplsNonTeMappingXcIndex holds the XC index in the
MPLS-LSR-STD-MIB of the PSN-bound outer tunnel.
pwMplsNonTeMappingIfIndex MUST be zero for this row.
- If the pwMplsMplsType pwOnly(2) bit is set, the agent
creates a row for the outbound direction
(pwMplsNonTeMappingDirection set to psnBound(1)).
The pwMplsNonTeMappingIfIndex holds the ifIndex of the
physical port this PW will use in the outbound direction.
pwMplsNonTeMappingXcIndex MUST be zero for this row.
- If the PW has been set up by a signaling protocol (i.e.,
pwOwner equal pwIdFecSignaling(2) or
genFecSignaling(3)), the agent creates a row for the
inbound direction (pwMplsNonTeMappingDirection set to
fromPsn(2)).
The pwMplsNonTeMappingXcIndex holds the XC index in the
MPLS-LSR-STD-MIB of the PW LDP-generated XC entry.
pwMplsNonTeMappingIfIndex MUST be zero for this row.
An application can use this table to quickly retrieve the
PW carried over specific non-TE MPLS outer tunnel or
physical interface.
"
INDEX { pwMplsNonTeMappingDirection,
pwMplsNonTeMappingXcIndex,
pwMplsNonTeMappingIfIndex,
pwMplsNonTeMappingPwIndex }
::= { pwMplsNonTeMappingTable 1 }
PwMplsNonTeMappingEntry ::= SEQUENCE {
pwMplsNonTeMappingDirection INTEGER,
pwMplsNonTeMappingXcIndex MplsIndexType,
pwMplsNonTeMappingIfIndex InterfaceIndexOrZero,
pwMplsNonTeMappingPwIndex PwIndexType
}
Zelig & Nadeau Standards Track [Page 19]
RFC 5602 PW MPLS MIB July 2009
pwMplsNonTeMappingDirection OBJECT-TYPE
SYNTAX INTEGER {
psnBound (1),
fromPsn (2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for the conceptual XC row identifying the tunnel-to-PW
mappings, indicating the direction of the packet flow for
this entry.
psnBound(1) indicates that the entry is related to
packets toward the PSN.
fromPsn(2) indicates that the entry is related to
packets coming from the PSN.
"
::= { pwMplsNonTeMappingEntry 1 }
pwMplsNonTeMappingXcIndex OBJECT-TYPE
SYNTAX MplsIndexType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"See the description clause of pwMplsNonTeMappingEntry for
the usage guidelines of this object."
::= { pwMplsNonTeMappingEntry 2 }
pwMplsNonTeMappingIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"See the description clause of pwMplsNonTeMappingEntry for
the usage guidelines of this object."
::= { pwMplsNonTeMappingEntry 3 }
pwMplsNonTeMappingPwIndex OBJECT-TYPE
SYNTAX PwIndexType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value that represents the PW in the pwTable."
::= { pwMplsNonTeMappingEntry 4 }
-- End of PW to Non-TE mapping Table.
-- PW to TE MPLS tunnels mapping Table.
Zelig & Nadeau Standards Track [Page 20]
RFC 5602 PW MPLS MIB July 2009
pwMplsTeMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwMplsTeMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table reports the PW association to the
outbound MPLS tunnel for MPLS-TE applications."
::= { pwMplsObjects 5 }
pwMplsTeMappingEntry OBJECT-TYPE
SYNTAX PwMplsTeMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents the association
between a PW and its MPLS-TE outer (head-end) tunnel.
An application can use this table to quickly retrieve the
list of the PWs that are configured on a specific MPLS-TE
outer tunnel.
The pwMplsTeMappingTunnelInstance reports the actual
LSP out of the tunnel head-end that is currently
forwarding the traffic.
The table is indexed by the head-end indexes of a TE
tunnel and the PW index.
"
INDEX { pwMplsTeMappingTunnelIndex,
pwMplsTeMappingTunnelInstance,
pwMplsTeMappingTunnelPeerLsrID,
pwMplsTeMappingTunnelLocalLsrID,
pwMplsTeMappingPwIndex }
::= { pwMplsTeMappingTable 1 }
PwMplsTeMappingEntry ::= SEQUENCE {
pwMplsTeMappingTunnelIndex MplsTunnelIndex,
pwMplsTeMappingTunnelInstance MplsTunnelInstanceIndex,
pwMplsTeMappingTunnelPeerLsrID MplsLsrIdentifier,
pwMplsTeMappingTunnelLocalLsrID MplsLsrIdentifier,
pwMplsTeMappingPwIndex PwIndexType
}
Zelig & Nadeau Standards Track [Page 21]
RFC 5602 PW MPLS MIB July 2009
pwMplsTeMappingTunnelIndex OBJECT-TYPE
SYNTAX MplsTunnelIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Primary index for the conceptual row identifying the
MPLS-TE tunnel that is carrying the PW traffic."
::= { pwMplsTeMappingEntry 1 }
pwMplsTeMappingTunnelInstance OBJECT-TYPE
SYNTAX MplsTunnelInstanceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies the MPLS-TE LSP that is carrying the
PW traffic. It MUST return the value zero if the
information of the specific LSP is not yet known.
Note that based on the recommendation in the
MPLS-TC-STD-MIB, instance index 0 should refer to the
configured tunnel interface."
::= { pwMplsTeMappingEntry 2 }
pwMplsTeMappingTunnelPeerLsrID OBJECT-TYPE
SYNTAX MplsLsrIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies the peer LSR when the outer tunnel
is MPLS-TE."
::= { pwMplsTeMappingEntry 3 }
pwMplsTeMappingTunnelLocalLsrID OBJECT-TYPE
SYNTAX MplsLsrIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies the local LSR."
::= { pwMplsTeMappingEntry 4 }
pwMplsTeMappingPwIndex OBJECT-TYPE
SYNTAX PwIndexType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object returns the value that represents the PW in the
pwTable."
::= { pwMplsTeMappingEntry 5 }
Zelig & Nadeau Standards Track [Page 22]
RFC 5602 PW MPLS MIB July 2009
-- End of PW to TE MPLS tunnels mapping Table.
-- conformance information
pwMplsGroups OBJECT IDENTIFIER ::= { pwMplsConformance 1 }
pwMplsCompliances OBJECT IDENTIFIER ::= { pwMplsConformance 2 }
-- Compliance requirement for fully compliant implementations.
pwMplsModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for agents that provide full
support for the PW-MPLS-STD-MIB module. Such devices
can then be monitored and also be configured using
this MIB module."
MODULE -- this module
MANDATORY-GROUPS { pwMplsGroup,
pwMplsOutboundMainGroup,
pwMplsInboundGroup,
pwMplsMappingGroup
}
GROUP pwMplsOutboundTeGroup
DESCRIPTION "This group MUST be supported if the implementation
allows MPLS-TE tunnels to carry PW traffic.
"
OBJECT pwMplsMplsType
DESCRIPTION "Support of pwOnly(2) is not required. At least one
of mplsTe(0) or mplsNonTe(1) MUST be supported if
signaling of PW is supported.
"
OBJECT pwMplsExpBitsMode
DESCRIPTION "Support of specifiedValue(2) and
serviceDependant(3) is optional.
"
OBJECT pwMplsLocalLdpID
MIN-ACCESS read-only
DESCRIPTION "A read-write access is required if the
implementation supports more than one LDP entity
identifier for PW signaling.
"
OBJECT pwMplsLocalLdpEntityIndex
Zelig & Nadeau Standards Track [Page 23]
RFC 5602 PW MPLS MIB July 2009
MIN-ACCESS read-only
DESCRIPTION "A read-write access is required if the
implementation supports more than one LDP entity
index for PW signaling.
"
OBJECT pwMplsOutboundLsrXcIndex
MIN-ACCESS read-only
DESCRIPTION "A value other than zero MUST be supported if the
implementation supports non-TE signaling of the
outer tunnel.
A read-write access MUST be supported if the
implementation supports PW label manual setting
and carrying them over non-TE tunnels.
"
OBJECT pwMplsOutboundIfIndex
MIN-ACCESS read-only
DESCRIPTION "A value other than zero and read-write operations
MUST be supported if the implementation supports
manually configured PW without MPLS outer tunnel.
"
::= { pwMplsCompliances 1 }
-- Compliance requirement for Read Only compliant implementations.
pwMplsModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for agents that provide read-
only support for the PW-MPLS-STD-MIB module. Such
devices can then be monitored but cannot be configured
using this MIB module."
MODULE -- this module
MANDATORY-GROUPS { pwMplsGroup,
pwMplsOutboundMainGroup,
pwMplsInboundGroup,
pwMplsMappingGroup
}
GROUP pwMplsOutboundTeGroup
DESCRIPTION "This group MUST be supported if the implementation
allows MPLS-TE tunnels to carry PW traffic.
"
OBJECT pwMplsMplsType
MIN-ACCESS read-only
Zelig & Nadeau Standards Track [Page 24]
RFC 5602 PW MPLS MIB July 2009
DESCRIPTION "Write access is not required.
Support of pwOnly(2) is not required. At least one
of mplsTe(0) or mplsNonTe(1) MUST be supported if
signaling of PW is supported.
"
OBJECT pwMplsExpBitsMode
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
Support of specifiedValue(2) and serviceDependant(3)
is optional.
"
OBJECT pwMplsExpBits
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
"
OBJECT pwMplsTtl
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
"
OBJECT pwMplsLocalLdpID
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
"
OBJECT pwMplsLocalLdpEntityIndex
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
"
OBJECT pwMplsStorageType
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
"
OBJECT pwMplsOutboundLsrXcIndex
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
A value other than zero MUST be supported if the
implementation supports non-TE signaling of the
outer tunnel.
"
OBJECT pwMplsOutboundTunnelIndex
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
"
Zelig & Nadeau Standards Track [Page 25]
RFC 5602 PW MPLS MIB July 2009
OBJECT pwMplsOutboundTunnelLclLSR
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
"
OBJECT pwMplsOutboundTunnelPeerLSR
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
"
OBJECT pwMplsOutboundIfIndex
MIN-ACCESS read-only
DESCRIPTION "Write access is not required.
A value other than zero MUST be supported if the
implementation supports manually configured PW
without MPLS outer tunnel.
"
::= { pwMplsCompliances 2 }
-- Units of conformance.
pwMplsGroup OBJECT-GROUP
OBJECTS {
pwMplsMplsType,
pwMplsExpBitsMode,
pwMplsExpBits,
pwMplsTtl,
pwMplsLocalLdpID,
pwMplsLocalLdpEntityIndex,
pwMplsPeerLdpID,
pwMplsStorageType
}
STATUS current
DESCRIPTION
"Collection of objects needed for PW over MPLS PSN
configuration."
::= { pwMplsGroups 1 }
pwMplsOutboundMainGroup OBJECT-GROUP
OBJECTS {
pwMplsOutboundLsrXcIndex,
pwMplsOutboundIfIndex,
pwMplsOutboundTunnelTypeInUse
}
STATUS current
DESCRIPTION
Zelig & Nadeau Standards Track [Page 26]
RFC 5602 PW MPLS MIB July 2009
"Collection of objects needed for outbound association of
PW and MPLS tunnel."
::= { pwMplsGroups 2 }
pwMplsOutboundTeGroup OBJECT-GROUP
OBJECTS {
pwMplsOutboundTunnelIndex,
pwMplsOutboundTunnelInstance,
pwMplsOutboundTunnelLclLSR,
pwMplsOutboundTunnelPeerLSR
}
STATUS current
DESCRIPTION
"Collection of objects needed for outbound association of
PW and MPLS-TE tunnel."
::= { pwMplsGroups 3 }
pwMplsInboundGroup OBJECT-GROUP
OBJECTS {
pwMplsInboundXcIndex
}
STATUS current
DESCRIPTION
"Collection of objects needed for inbound PW presentation.
This group MUST be supported if PW signaling through LDP is
used."
::= { pwMplsGroups 4 }
pwMplsMappingGroup OBJECT-GROUP
OBJECTS {
pwMplsNonTeMappingPwIndex,
pwMplsTeMappingPwIndex
}
STATUS current
DESCRIPTION
"Collection of objects needed for mapping association of
PW and MPLS tunnel."
::= { pwMplsGroups 5 }
END
Zelig & Nadeau Standards Track [Page 27]
RFC 5602 PW MPLS MIB July 2009
9. Security Considerations
It is clear that this MIB module is potentially useful for monitoring
PW-capable PEs. This MIB module can also be used for configuration
of certain objects, and anything that can be configured can be
incorrectly configured, with potentially disastrous results.
There are number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
o the pwMplsTable, pwMplsNonTeMappingTable and pwMplsTeMappingTable
collectively contain objects to provision PW over MPLS tunnels.
Unauthorized access to objects in these tables, could result in
disruption of traffic on the network. The use of stronger
mechanisms such as SNMPv3 security should be considered where
possible. Specifically, SNMPv3 VACM and USM MUST be used with any
v3 agent which implements this MIB module. Administrators should
consider whether read access to these objects should be allowed,
since read access may be undesirable under certain circumstances.
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP. These are the tables and objects and their
sensitivity/vulnerability:
o the pwMplsTable, pwMplsNonTeMappingTable, pwMplsTeMappingTable and
pwMplsOutboundTable collectively show the PW over MPLS
association. If an Administrator does not want to reveal this
information, then these tables should be considered sensitive/
vulnerable.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
Zelig & Nadeau Standards Track [Page 28]
RFC 5602 PW MPLS MIB July 2009
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module, is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
10. IANA Considerations
The MIB module in this document uses the following IANA-assigned
OBJECT IDENTIFIER values recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
pwMplsStdMIB { mib-2 181 }
11. References
11.1. Normative References
[BCP14] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Structure of Management Information Version 2 (SMIv2)",
STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Textual Conventions for SMIv2", STD 58, RFC 2579, April
1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
Label Switching Architecture", RFC 3031, January 2001.
Zelig & Nadeau Standards Track [Page 29]
RFC 5602 PW MPLS MIB July 2009
[RFC3811] Nadeau, T., Ed., and J. Cucchiara, Ed., "Definitions of
Textual Conventions (TCs) for Multiprotocol Label
Switching (MPLS) Management", RFC 3811, June 2004.
[RFC3812] Srinivasan, C., Viswanathan, A., and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Traffic Engineering
(TE) Management Information Base (MIB)", RFC 3812, June
2004.
[RFC3813] Srinivasan, C., Viswanathan, A., and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB)", RFC 3813,
June 2004.
[RFC4447] Martini, L., Ed., Rosen, E., El-Aawar, N., Smith, T., and
G. Heron, "Pseudowire Setup and Maintenance Using the
Label Distribution Protocol (LDP)", RFC 4447, April 2006.
[RFC5542] Nadeau, T., Ed., Zelig, D., Ed., and O. Nicklass, Ed.,
"Definitions of Textual Conventions for Pseudowire (PW)
Management", RFC 5542, May 2009.
[RFC5601] Nadeau, T., Ed. and D. Zelig, Ed. "Pseudowire (PW)
Management Information Base (MIB)", RFC 5601, July 2009.
11.2. Informative References
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
[RFC3815] Cucchiara, J., Sjostrand, H., and J. Luciani, "Definitions
of Managed Objects for the Multiprotocol Label Switching
(MPLS), Label Distribution Protocol (LDP)", RFC 3815, June
2004.
[RFC3916] Xiao, X., Ed., McPherson, D., Ed., and P. Pate, Ed.,
"Requirements for Pseudo-Wire Emulation Edge-to-Edge
(PWE3)", RFC 3916, September 2004.
[RFC3985] Bryant, S., Ed., and P. Pate, Ed., "Pseudo Wire Emulation
Edge-to-Edge (PWE3) Architecture", RFC 3985, March 2005.
Zelig & Nadeau Standards Track [Page 30]
RFC 5602 PW MPLS MIB July 2009
Authors' Addresses
David Zelig (editor)
Oversi Networks
1 Rishon Letzion St.
Petah Tikva
Israel
Phone: +972 77 3337 750
EMail: davidz@oversi.com
Thomas D. Nadeau (editor)
BT
BT Centre
81 Newgate Street
London EC1A 7AJ
United Kingdom
EMail: tom.nadeau@bt.com
Zelig & Nadeau Standards Track [Page 31]