The comp.sys.apple2 Usenet newsgroup Apple II FAQs originate from the Ground Apple II archive, 1997-2005. Administrator: Steve Nelson Csa2 FAQs-on-Ground ref: Csa2ACCEL.txt rev086 May 2005 Accelerators 001- What are the correct settings for a ZipGS? 002- Why should Appletalk Delay be disabled with a ZipGS? 003- How do I set up a Transwarp on my IIe? 004- Is there a way of disabling Transwarp for games? 005- What are specs & jumper settings for a vintage SpeeDemon? 006- How does the SpeeDemon rate as an accelerator? 007- My SpeeDemon accelerator board seems to run hot. A fix? 008- How should the DIP switches be set on a v3.03 SpeeDemon? 009- How can I get a 'Cache Hit' indicator for my ZipGS? 010- How can I program the ZipGS registers? 011- How can I set up a ProDOS sys file to turn my ZipGS OFF/ON? 012- Is there some ZipGS mod that will improve performance? 013- I have a 7MHz ZipGS. How fast can the board be pushed? 014- What Oscillator freq corresponds to what upgrade speed? 015- How do I experiment with different oscillator frequencies? 016- How do I modify my ZipGS to accept the new "skinny" RAM chips? 017- Is it really necessary to increase board voltage 018- What kind of performance increase can I expect? 019- How can I modify my ZipGS for more cache and more speed? 020- Do I need new GALs to speed up my TransWarpGS? 021- How does a TWGS cache upgrade compare with a speed upgrade? 022- How can I upgrade my TWGS to 32k cache? 023- How can I upgrade TWGS speed? 024- What kind of RAMs do I need for a TWGS or ZipGS speedup? 025- How can I tell the firmware version of my TWGS? 026- For my TWGS, do I need the 2B GAL to use a SCSI interface card? 027- Why are my ZipGS settings via the Zip CDA forgotten? 028- What do the check-marks mean in the ZipGS CDA? 029- Why don't my ZipGS settings match DIP switch settings!? 030- I have a ZipGS. Sometimes my GS 'hangs' on power-up. Why? 031- The speedup has led to system crashes. What's the problem? 032- A new accelerator board has led to crashes. What's the problem? 033- How can I get a display of IIgs speed? From: Marc Sira, David Empson, Rubywand 001- What are the correct settings for a ZipGSx? I've tinkered with "CPS Follow", "Counter Delay", and the like but have no idea what I'm actually doing. Bank C/D cache enable -- Leave this at the default setting (SW1-1 set to ON). This tells the Zip if it's OK to cache bank-switched RAM (the old language card area). Zip's own docs say "there is no know software requiring this" but that it why it's there, in case somebody ever finds software that doesn't like it you can try setting it the other way. Paddle Delay lets your paddles or joystick work the way they do on 8-bit Apple II's or an unaccelerated IIgs. The delay is necessary for playing most 8-bit games which use paddles or a joystick. Recommended setting is to have the delay active (SW1-2 set to OFF) unless you feel like experimenting. AppleTalk or Interrupt Delay should always be disabled (SW1-3 set to ON). The desktop will run much slower if you enable it. The only reason most people needed it was for AppleTalk under system 5, and now there is an init on tybalt that fixes that. System 6 fixed the problem but requires CPS Follow to be enabled for the fix to work. Counter Delay is really present just so that the ZipGS can be set to get past one of the early IIgs diagnostic self-tests. It causes the Zip to "deaccelerate" (actually all it does is temporarily ignore that any data can be read from the cache instead of the motherboard) for about 5 milliseconds any time you read one of the Video Counters. To get pass the particular self-test, SW1-4 should be set to OFF (delay active). Otherwise, the recommended setting is SW1-4 set to ON. CPS Follow should always be enabled (SW1-5 set to OFF). It causes the ZipGS to auntomatically 'follow' the IIgs-- when it switches to "Normal" speed, the ZipGS is disabled. This is a requirement for a reasonable amount of timing-critical software. If you disable CPS Follow you will have problems with Disk ]['s and System 6's AppleTalk driver and anything else that expects the Zip to slow down to 1 mhz when the IIgs is instructed to slow down to 1MHz. For instance, border text demos (like the FTA XMAS demo) won't work if you have this disabled. Expect weird things to happen if you play with this one. ZipGS Enable-- The card should normally be enabled (SW1-6 set to ON). SW1-7 and SW1-8 should be set to correspond to the size of your ZipGS's cache memory. (see below) SW2-1 through SW2-7 control slot delays for Slots 1-7. Set the switch OFF to enable the delay for the corresponding Slot. This is generally only needed for a small number of cards that are speed critical but not IIgs-aware. 5.25" disk interface cards are covered by the CPS FOLLOW option (1-5) if they are in slots 4 to 7. I have found that it is necessary to enable the delay for slot 6 when using a 3.5" drive connected to the IIgs disk port. There are a few rare cases in which a long timed operation is performed in fast mode, and the ZIP throws the timing out unless this delay is enabled. In my case, I had some strange disk errors with certain disks until I enabled this delay. Speaker Delay lets "old Apple II" 1-bit sounds play the way they would on 8-bit Apple II's or an unaccelerated IIgs. The delay is necessary for getting correct sound from most 8-bit games. I recommend having the delay active (SW2-8 set to OFF). Summary The normally recommended SW1 settings are identical to the factory default settings except for SW1-4 ... ON x x x x m m OFF x x m m 1 2 3 4 5 6 7 8 1- Cxxx/Dxxx Cache: ON= enabled. 2- Defeat Joystick delay: OFF= allow delay. 3- Defeat AppleTalk delay: ON= no delay. 4- Defeat Counter Delay: ON= no delay. Set OFF to pass IIgs diagnostic self-test #05 ("Speed Test"). 5- Defeat CPS Follow: OFF for floppy drives to work. 6- ZipGS enable: ON. (Set OFF to allow powerup boot in slow mode and use an Init to turn GS back ON.) 7 & 8- Set these to installed Zip cache memory size: ON ON 8k ON OFF 16k OFF ON 32k OFF OFF 64k The factory default SW2 settings are ... ON x x x x x OFF x x x 1 2 3 4 5 6 7 8 SW2-1 through SW2-7 control whether a card in Slot 1-7 is accessed at full speed (set ON) or "normal" speed (set OFF)*. SW2-8 sets Defeat Speaker Delay. To play 'old Apple' music and effects correctly, the switch should be OFF to permit the delay. *Note: Whether or not a particular card can work without a slow-down is something you can determine by experimentaton. This is easiest using the Zip CDA accessed via the Desk Accessories menu (OpenApple-Control-Escape). The CDA settings are not permanent. Once you find the settings you like, you can turn OFF the computer and set the switches on the board to match the settings that work best. ____________________________ From: Todd P. Whitesel 002- Why should Appletalk Delay be disabled with a ZipGS? Because it saps performance every time an interrupt occurs. The Appletalk delay was originally called the "Interrupt Delay" but they renamed it at the last minute because somebody actually tried an 8/64 on an Appleshare network and it dropped packets like crazy. With "Appletalk delay" on, every time an interrupt occurs your Zip will disable acceleration for 5 ms, just like it does with the paddles and the speaker and the others. This is a significant effect because with VBL interrupts going you have one every 16 ms, so your Zip spends nearly 1/3 of the time not accelerating you. Why this "fixes" appletalk: in system 5 and earlier (including the ROM appletalk code), there are software timing loops which assume 2.8 mhz operation. As you speed the system up, it gets more and more likely to drop incoming packets because it thinks they are being sent too slowly to be correct, when in reality the appletalk code is timing out too fast. Why the Appletalk delay is not a complete solution: a full-size Appletalk packet that you'd get from a file server takes about 14 ms to transmit. The Appletalk delay covers the first 1/3 of the packet, the VBL interrupt covers at most another third of the packet, but nothing is guaranteed to keep acceleration off for the whole packet. If you speed the Zip up more, say to 10/64, it starts dropping long packets no matter what. This latter problem was why I originally wrote ZipTalk. It required a slot delay to be enabled (in, say, slot 6 or 7), and before each appletalk packet was received I tweaked that slot -- slot delays are 50 ms, so the Zip stays unaccelerated way past the end of the packet and everything works. (I also patched packet sending, to be safe.) In system 6 Apple fixed things correctly in the appletalk drivers. I removed the code from ZipTalk and released what remained as ZipFix. As of 6.0.1, the cursor flicker problem was fixed by apple in the control panel, so now you only need ZipFix for the GS/OS SET_SYS_SPEED hook, which nobody seems to use. ______________________________ From: Jeff Brielmaier 003- How do I set up a Transwarp on my IIe? Bank1: Sw 1-7 -> Change to OPEN if there is a memory card that uses the "Langauge Card bank switching technique". (Normally CLOSED) Bank1: Sw 1-7 -> Change to OPEN if the plug in card must be accessed at 1 MHz (Normally CLOSED. OPEN for Floppy diskette controllers) Switch 8 on both Banks: Sets the power up speed of Transwarp Bank1 Bank2 3.6 MHz OPEN OPEN <> 1.7 MHz CLOSED OPEN 1 MHz OPEN CLOSED 1 MHz CLOSED CLOSED ---------------------- 004- Is there a way of disabling Transwarp for games? Press at power-up will disable Transwarp completely until the next power off/on cycle. A better way is to write a 01 to $C074. This will slow Transwarp down to 1 MHz without disabling it completely. Writing a 00 to $C074 will restore Transwarp to it's 'fast' speed. ____________________________ From: Rubywand 005- I recently bought an "M-c-T SpeeDemon" board. It's dated 1984 and draws a small apple on the screen after power-up. What kind of cache RAM does it have? There's a place for jumpers near the top of the card. Is there a way to control this thing through software or hardware? Your card may be a slightly later model. (I've never noticed ours draw a hires apple on the screen-- darn it!) Possibly, McT came out with a revision aimed at 128K IIe's. The RAMs on our vintage model SpeeDemon are 100ns 2048x8 9128's (for a total 8K of pretty speedy cache). I once asked McT about the jumper block you mention, they said the jumper is set at the factory to adjust on-card timing and to Leave It Alone. (On our card, the jumper block has 5 pairs. The pair 2nd from the top is jumpered.) There is also a jumper pair near the bottom middle of the card. This is the Speed Jumper. Jumper it if you want 'demon to slow down for I/O accesses to Slots 4 & 5. (The 'demon always slows for Slot 6 I/O ($C0E0 - $C0EF.) According to the "Manual" (a folded card), pressing PDL-1 (Closed-Apple on a IIe) upon power-up will engage a self-test. Pressing ESC at power-up will turn OFF the card and allow running at normal speed. To turn OFF the card later on, do a POKE (49152+256*S) where S= Slot # of the slot the card is in; then, press RESET. You can put the 'demon into any Slot; but, if you put it in Slot 0 (Slot 3 in a IIe), the card will not respond to any KB shut-off commands. ------------------------ 006- How does the SpeeDemon rate as an accelerator for II+ and IIe Apples? In terms of raw performance (once you arrange for cooling), SpeeDemon may be the best of the 4MHz accelerators for early II's. I've never noticed any compatibility problems and the approx. X3.5 speed increase puts real 'snap' into your machine's response. (Besides, it's great for games like Elite!) ------------------------ 007- My SpeeDemon accelerator board seems to run hot in my II+. Is this normal? Should I add cooling? Indeed, the 'demon is a power gobbler-- roughly 1.5A as I recall-- and some of the IC's run hot. When the board bombed after one long session, we cut out a square section on the back of the II+ and added a mini-fan, just to blow air across the 'Demon board. This ended the heat problem. ____________________________ From: Douglas M. Howell 008- How should the DIP switches be set on a version 3.03 SpeeDemon board? This is from the 1-page manual that comes with the card: For owners without a Bank Switch Language Card in thier Apple, the first seven DIP switches control the access speed of the following: switch 1 -- controls -- slot 1 switch 2 -- " -- slot 2 switch 3 -- " -- slot 3 switch 4 -- " -- paddle/joystick port switch 5 -- " -- slot 5 switch 6 -- " -- slot 6 switch 7 -- " -- slot 7 OFF indicates slot/port is accessed at High Speed. ON indicates slot/port is to Slow Down for access. All slots that can be accessed at High Speed and all empty slots should have the corresponding Dip switch set to "OFF" (this is the non-bank switch setting). Special Note about Switch 4: Switch 4 on the SpeeDemon DIP switch no longer controls the access speed to slot 4. It now controls how the joystick and paddles are read. If switch 4 is in the "ON" position, the SpeeDemon will slow down to normal Apple speed for 50 milliseconds each time the joystick is accessed. This allows the software to read the joystick or paddles correctly. If switch 4 is in the "OFF" position, the SpeeDemon will not slow down when they are accessed. Access to slot 4 is always at SLOW (normal) Apple speed. Certain programs, such as Appleworks, use the joystick location, even when the joystick is not in use. If dip switch 4 is set to "ON" then these programs will not show any speed for some functions, such as calculations and sorts. Therefor, unless you need youysticks for your applications, switch 4 should be set in the "OFF" position. If you have a Bank Switch Card (extended 80-col card, Ramworks II, Titan Saturn 128k card, excetera..) set switch 8 to the "ON" position. Bank Switch Language Card Location: Dip Switches 1-3 encode the location of your Bank switch language card. Use the following table to find the appropriate setting for your machine: Dip Switch Bank Switch Card Location 1 2 3 Slot # --- --- --- ------ off off off 0 off off on 1 off on off 2 off on on 3 on off off 4 on off on 5 on on off 6 on on on 7 If you have two bank switch cards in your system, one must reside in slot 0. The other must be in the slot selected by DIP switches 1-3 above. Special Note: Because the first three switches are used to encode the location of the Bank Switch Language Card, you can no longer control the speed of all the slots. Specifically you can not control slots 1,3, or 6. These slots woll now always run Fast except for slot 6 which will always run Slow. Special Note: The slot that the SpeeDemon card resides in should be set to the "Off" position ____________________________ From: Will Baguhn 009- How can I get a 'Cache Hit' indicator for my ZipGSx? This latest ZipGSx modification is pretty straightforward. When I decided I wanted a Cache HIT light instead of a Cache MISS light, I went to Rat Shack and bought a pack of Green LEDs (I like green. Blue or Orange will work just as well.) I tried adding an inverter to the circuit but it just didn't want to play (obviously a cache HIT is the opposite of a cache MISS, and the LED on the board lights up for cache MISSes). Through the experimenting, I found that I could get the LED to light as desired without any "extra" hardware except the LED itself. Simple mod: solder in the Anode of the LED to the Anode of the Cache Miss. Solder the Cathode to the Cathode of the Power LED. (Even easier way to say it: there are four solder points for the existing LEDs. We use the two in the middle. The long lead goes to the yellow side, the short to the red. position as is comfortable. I can only guess that this would be a nice thing to attach to the TURBO light on the front of a tower case, should anyone ever mount a IIgs/ZipGSX inside a tower case... (also, it might be nice to turn SW1-6 OFF and connect the pins to the TURBO button on front. I don't know how useful it would be, but it might come in handy one of these days...) ____________________________ From: David Empson 010- How can I program the ZipGSx registers? ZipChip GS Special Registers Ex ZIP Technology, 12 October 1990 Registers must be unlocked before they can be accessed (see $C05A). Locking them will re-enable the annunciators. Writing to any I/O location $C058-$C05F (whether registers are locked or unlocked) will reset delay in progress. $C058 R No operation $C058 W Write any value to force power-on/reset bit to COLD (forces next reset to restore ZIP registers to defaults/switch settings). $C059 R/W 76543210 *....... Bank Switch Lang Card cache disable=1/enable=0? .*...... Padl delay (5 ms) disable=0/enable=1 $C070/$C020 ..*..... External delay (5 ms) disable=0/enable=1 ...*.... Cntr delay (5 ms) disable=0/enable=1 $C02E/$C07E ....*... CPS follow disable=0/enable=1 .....*.. Last Reset warm? READ ONLY ......*. Hardware DMA READ ONLY .......* non-GS (0)/GS (1) READ ONLY $C05A R 76543210 ****.... Current ZIP Speed, 0=100%, 1=93.75%,..., F=6.25% ....1111 $C05A W Write values as follows: $5x Unlock ZIP registers (must write 4 times) $Ax Lock ZIP registers other Force ZIP to follow system clock (disable card) $C05B R 76543210 *....... 1msclk - clock with 1 ms period .*...... cshupd - Tag data at $C05F updated (read $C05F to reset) ..*..... Bank Switch Language Card cache (0), don't (1) ...*.... Board disable - 0=enabled, 1=disabled ....*... delay in effect (0=ZIP, 1=Slow) .....*.. rombank (0/1) - not in development version ......** Cache RAM size (00=8k, 01=16k, 10=32k, 11=64k) $C05B W Write any value to force ZIP to current speed (i.e. enable card) $C05C R/W 76543210 *******. Slot 7-1 delay enable (all slots 52-54 ms) .......* Speaker delay enable (5 ms) $C05D R Current 65816 bank $C05D W 76543210 ****.... Set ZIP speed, 0=100%, 1=93.75%, ..., F=6.25% ....**** Don't care $C05E R Read last Tag data written and force the next write to create a trash tag value. $C05E W No operation $C05F R Read last Tag data written and reset cshupd. Note: apparently any write to a ZIP register (unlocked) will clear cshupd, but cshupd says that this location must be read. $C05F W No operation ---------------------------- 011- Is it possible to set up a simple ProDOS-8 application (SYS) file which turns the ZipGS OFF or ON? From the usual BASIC prompt, get into the Monitor (e.g. CALL -151) and type in the following code to turn OFF the ZipGS ... 2000:A9 50 8D 5A C0 8D 5A C0 8D 5A C0 8D 5A C0 8E 5A 2010:C0 0A 8D 5A C0 20 00 BF 65 1D 20 00 00 04 00 00 2020:00 00 00 00 A 2000L should look something like this ... 2000: A9 50 LDA #$50 2002: 8D 5A C0 STA $C05A ; write $50 to $C05A four times to 2005: 8D 5A C0 STA $C05A ; enable access to the ZIP registers 2008: 8D 5A C0 STA $C05A 200B: 8D 5A C0 STA $C05A 200E: 8E 5A C0 STZ $C05A ; write $00 to $C05A to disable ZIP 2011: 0A ASL = SLOW mode 2012: 8D 5A C0 STA $C05A ; write $A0 to stop accessing ZIP 2015: 20 00 BF JSR $BF00 ; Do a ProDOS QUIT call 2018: 65 $65 2019: 1D 20 $201D 201B: 00 00 BRK $00 201D: 04 00 00 00 00 00 00 Use the following commands to save it: CREATE SLOW,TSYS BSAVE SLOW,TSYS,A$2000,L$24 To enable the ZipGS (= FAST mode), simply change one byte: 200F:5B (this changes the STZ $C05A to STZ $C05B) CREATE FAST,TSYS BSAVE FAST,TSYS,A$2000,L$24 ____________________________ From: William Baguhn Reference: FAQs resource file R005SPLITC.GIF (pic file) 012- Is there some ZipGSx mod that will improve performance without going to a faster crystal, etc.? There is; you can do the ZipGSx Split Cache Mod. As your manual explains, Zip GSX speed comes from having a faster processor which can access code and data from its high-speed cache RAM. The standard 'GSX has a unified cache, which means data and code have the possibility of overlapping. If the cache controller sees a need to bring in a lot of code, it will go to main memory and bring in up to 64k of code (or 16k in a 16k cache system) and, possibly, overwrite useful data. The reverse is also true. If the controller feels that a lot of data needs to be brought in, it will cache the data, and, possibly, overwrite useful code, causing another slowdown when the code needs to be fetched again. With a split cache, the code and data segments no longer overlap. Caching code cannot overwrite data, caching data cannot overwrite code. The drawback is that only 32k of data and 32k of code can be cached at once (in a 64k system), but usually this provides for more speed than being able to cache a 64k mix of both. To do the mod, you'll need a ZipGSX version 1.02 with either 16k or 64k cache on it. If you're not sure exactly what board you have, it's pretty straightforward to figure things out: open the computer and look at the Zip. The board revision is silkscreened on just beneath the processor. The cache size can be determined from the DIP switch settings. However, a simpler guideline is look at the TAG/DATA sockets and count the number of chips. If there are only 2 chips, you have either an 8k or a 32k cache. If there are 4, then you should have 16k or 64k. To modify your Zip for the Split Cache, you'll need a good hobby knife that can cut the traces without damaging the board underneath too badly, as well as two or three small lengths of wire. You will also need a good pencil-style soldering iron, desoldering pump or braid, and high quality rosin core (NOT acid core) solder. I use Radio Shack's .032 60/40 rosin core solder. Kester makes excellent quality solder which is sold at many electronics supply shops. There is a potential of damaging expensive and delicate hardware. For example, when cutting a circuit trace be careful not to cut deeply, lest you cut a trace in the next layer of the circuit board. If you're not experienced with cutting traces or soldering on circuit boards, find an old board and take some time to practice. The actual mod is very simple. Steps 1-3 and 5 are for all boards. Step 4 is for 16k cache boards only. (Note: The picture in FAQs resource file R005SPLITC may be helpful for doing these mods.) 1. Locate J6 and J7. They are both blocks of 3 pinholes, which may or may not have been soldered-in, near the bottom of the board next to connector J1, where the gray cable attaches. 2. Cut the SMALL trace between pins 2 and 3 of both J6 and J7. This trace is on the back (solder side) of the board. 3. Solder in a piece of wire between pins 1 and 3, of both J6 and J7. A wire that has been bent into a U shape before soldering seems to work best, both for ease of installation and aesthetic value. 4. 16k systems ONLY: (See the "16k" insert on the picture in FAQs resource file R005SPLITC.) Cut the trace between pins 1 and 2 of J8 on the top side of the board. (J8 is below the Cache SRAM sockets) Then, solder a piece of wire between pins 2 and 3 of J8. 5. Set the DIP switches appropriately. The DIP switches needing to be set are SW1-7 and SW1-8, they control the cache size. SW1-7 should be OFF for 64k, ON for 16k. SW1-8 should be ON. Reversing these changes is fairly easy. If you decide that the performance change was detrimental, simply desolder the wires that you installed, and solder in wires to replace the traces that were cut. I found that the split cache sped up my system notably, especially under the Finder and other desktop applications. Improvement was much less noticeable under text applications. (I haven't checked affect on compiling speed, yet.) ---------------------------- From: Rubywand I tried the split-cache mod on my 10MHz/64kB ZipGSx. Before/after timings were done for several tasks including Scrolls through Finder windows, Scrolls and Find/Replace through Coolwriter (super-res) and Appleworks (plain text) documents, and Platinum Paint fills. Timing differences were very small-- usually within the error normally experienced when clicking a stopwatch for repetitions of identical events. Where a difference was observable, it favored the unified 64kB cache. Evidently, at least on a 64kB board, the ZipGS does a fairly good job of managing the unified cache. Possibly, the mod comes out ahead in some tasks not sampled; or, it may work better on 16kB boards. ____________________________ From: Richard Der 013- I have a 7MHz ZipGS. How fast can the board be pushed without getting new SRAMs or a new CPU? What parts do I need? You may be able to get it to run at up to 10MHz by just replacing the oscillator with a faster one for less than two dollars! I have a Zip GS that came as a 7/32 and was used at 7MHz for a long time. The board came with a socketed oscillator, so one day I swapped out the 28MHz oscillator for a 36MHz one. The computer booted up at 9MHz. When the 36MHz osc was replaced with a 40MHz osc, the Zip ran at an amazing 10MHz! Your mileage may vary, though. The GS that this upgraded Zip resides in has a high output power supply. Still, considering these oscillators cost $1.39 each, it is worth getting three or four and trying an oscillator swap alone first. If a faster oscillator alone won't do the trick, then a faster CPU and/or faster cache chips may be necessary. Good Luck! ____________________________ From: Frank M. Lin 014- What Oscillator freq corresponds to what TWGS/ZipGS operating speed? For TWGS and ZipGS, the crystal oscillators runs at 4 times the speed of the 65816. Below is a chart showing osc and corresponding TWGS or ZipGS speed. Osc Frequency MHz TWGS/ZipGS Speed MHz 28 7 32 8 33.3333 8.3333 36 9 40 10 42 10.5 46 11.5 48 12 50 12.5 55 13.75 60 15 My understanding is that, if you over-clock a CPU. It just won't function. You can't damage it. As the disclaimer said, do it at your own risk. I have tried to run my TWGS at 20 MHz, system won't boot at all. No damage. ---------------------------- 015- How do I experiment with different oscillator frequencies? Most of the following is from a piece on ZipGS upgrading by Long. It is also a useful guide for TranswarpGS owners. The ZipGS can use three types of crystal oscillators: the common 4-pin "full size" oscillator module (about the size of a 14-pin TTL IC), a 4-pin "half size" oscillator module (also used on TWGS), or an on-card circuit with a separate crystal (little 2-pin metal canister). To be able to use a separate crystal, your ZipGS must have a resistor at R1 and capacitors at C13 and C14. These three parts are often omitted from Zips which use an oscillator module. If your accelerator does not have a socket for the oscillator module, you should probably install one (14-pin for ZipGS; 8-pin for TranswarpGS). Experimenting with different frequencies will be much easier. (If your ZipGS has eyelets for a 16-pin socket*, leave the top two pins open.) On ZipGS boards, only 6 of the 14 socket pins are connected (picture A). The Ground (GND) pins 1, 4, and 7 are connected together. The Power pins 11 and 14 are connected together; and, pin 8 is the module Output. Full size oscillator modules use pins 1, 7, 8 and 14 (refer to picture B). Half-size oscillator modules use the bottom four pins (4, 7, 8 and 11; picture C). TranswarpGS uses an 8-pin socket intended for holding a half size oscillator module (picture D). Make sure the module is oriented with the marked end (usually having a dot, squared corner, and/or notch) facing upward. Make sure the module is oriented with the marked end (usually having a dot and/or notch) facing upward. The lower two pins of the module should be in the lowest two pins of the socket. WARNING: The oscillator may be damaged if installed incorrectly. ZipGS * x x * _______ GND 1 o o 14 POWER 1 |o \ 14 NC x x NC | | NC x x NC | FULL | ______ GND 4 o o 11 POWER | SIZE | 1 |o \ 8 NC x x NC | | | HALF | NC x x NC | | | SIZE | GND 7 o o 8 OUTPUT 7 \______/ 8 4 \_____/ 5 (A) (B) (C) TranswarpGS ______ GND 1 o o 8 POWER 1 |o \ 8 NC 2 x x 7 NC | HALF | NC 3 x x 6 NC | SIZE | GND 4 o o 5 OUTPUT 4 \_____/ 5 x - no connection (NC) ---------------------------- 016- How do I modify my ZipGS to accept the new "skinny" RAM chips? With a little modification you can make a Zip with wide sockets accept both the wide (600 mil) and the newer 300 mil skinny 32k x 8 Static RAMs (SRAMs). Ground yourself then carefully pry out the static rams. Look at the socket and you will notice two or three horizontal bars holding both sides of the socket together (Picture D). Carefully snip those out (wire cutters work well for snipping plastic). This will expose a column of holes. Now, solder in half of a socket. Refer to Picture E below. Plug your skinny SRAMs into the left and center columns making sure the notch on the static ram is facing up-- i.e. toward top edge of board. (Applying power with a chip incorrectly socketed could damage the chip.) _______ Added center strip Snip out | ___ ___________ Skinny RAMs plug in here | | | | notched end facing up. ____ ____ _ _ _ |o __V__ o| |o| |o| |o| |o| o |o| |o| |o| |o| |o| o |o| |o| |o| |o| |o| o |o| |o| |o| |o| |o| o |o| |o| |o| |o| |o| o |o| |o| |o| |o| |o|__o__|o| |o| |o| |o| |o _____ o| |o| |o| |o| |o| o |o| |o| |o| |o| |o| o |o| |o| |o| |o| |o| o |o| |o| |o| |o| |o| o |o| |o| |o| |o| |o|__o__|o| |o| |o| |o| |o _____ o| |o| |o| |o| (D) (E) ----------------------------- 017- Is it really necessary to increase board voltage to do a TWGS/ZipGS speedup? With the new 14 MHz parts, you should not need to mess with the voltage at all. It _may_ be necessary to increase voltage at 15-16MHz and will likely be necessary at higher frequencies (e.g. 20MHz). ----------------------------- 018- If I do a TWGS/ZipGS speedup mod, what kind of performance increase can I expect? This is just to give you a rough estimate of how much faster you might be able to achieve... BenchMark v5.0 results: CPU Stock TWGS TWGS TWGS ZipGS ZipGS ZipGS Version ROM 01 1.8s 1.8s 1.8s 1.0.2 1.0.2 1.0.2 Cache/Spd 32k/15 32k/15 32k/15 64k/?? 64k/?? 64k/?? Clock Spd 2.8 15 13.75 12.5 16 15 14 ======= ====== ====== ====== ====== ====== ====== Sieve 410.00 99.00 108.00 117.00 98.00 99.00 110.00 String 1151.20 270.00 292.00 303.67 259.00 262.00 282.00 Float 1 472.00 92.33 87.00 111.33 123.00 128.00 135.00 Float 2 1535.00 317.00 394.00 381.67 395.00 415.00 432.00 Fibinacci 2006.00 605.00 634.00 645.33 507.00 523.00 548.00 Integer 1553.40 307.00 330.00 346.67 420.00 431.00 443.00 Dhrystone 236 1136 1063 1000 NA NA NA * 1351 1183 1282 NA NA * Dhrystone v1.1 re-compiled under ORCA/C v2.0.1 System Software 5.0 QuickDraw II improvement test: Stock //gs: 5648 ticks TWGS 15 MHz: 1332 ticks (over 4x faster than stock) If you look at the numbers, a 12 MHz or faster TWGS/Zip will make everything just about 4x faster than a stock //gs. ____________________________ From: Scott G. 019- How can I modify my ZipGS for more cache and more speed? The process described below is very simple. It aims for a speed of 12.5MHz (or better) with 64k cache. First, you will need one of the new Western Design Center 14MHz 65C816's. Students, teachers, and professors can order the IC in single quantities directly from WDC ( http://www.wdesignc.com ). Otherwise, the minimum order is $100. Price is about $20 each. adapters: Nearly all of the newer, faster 32k x 8 SRAMs are in skinny 300-mil packages. If you would rather not modify your ZipGS for the skinny SRAMs, Digi-Key stocks 28-pin 300-mil to 600-mil adapter sockets from Aries Electronics for about $12 each (Aries no. 1106396-28). You can plug a 28 pin SRAM into the 300-mil adapter socket and the adapter in turn plugs into the 600-mil socket on the Zip. (If you have some spare sockets lying around, you can build your own cheap, but that's another story.) 2-4 32k x 8 SRAM chips: There are many sources for 32k x 8 SRAMs and several types that will work. I got mine (HM62832-15, $5 each) from JDR Microdevices. You'll want 15ns in the Tag RAM sockets. Up to around 12.5MHz, you want 70ns or faster Data RAM. If current cache size is 64k, your old TAG RAM chips will, usually, work as Data RAM and can be transferred to the Data sockets. Otherwise, go ahead and get two 25ns-35ns 32k x 8 SRAM chips for the Data RAM. Data RAM should always be slower than Tag RAM. Barry Rees posted his experiences on this matter (that Data should be significantly slower than Tag) and I found that the original Tag chips were fast enough. A "full size" oscillator module: Digi-Key, JDR, Mouser, ... have these. Divide oscillator speed by four to get Zip speed. JDR has the OSC50.0 (50MHz oscillator), which will make a 12.5MHz Zip. The oscillators are cheap enough to get two or three for experimenting with higher speeds. So, you just plug your Tag and Data RAM chips into the Digi-Key adapters and plug the adapters into the Tag and Data sockets of the Zip. Then, you install the new 65C816 and oscillator and make sure DIP switch 1-7 and 1-8 are both set OFF (for 64k cache). That's it, done completely without soldering. ZipGS boards vary. On some you may be able to go above 12.5MHz by just plugging in a faster oscillator. On others, you may have to choose between getting faster Data RAM or settling for a lower speed. The new 65C816 is rated for 16MHz and many users have gone to 14MHz and above. For speeds above 12.5MHz, the usual recommendation is to get Data RAM rated at 35ns or better. For a step-by-step guide, download my ZipUpgrade.SHK HyperCard stack at ftp://ground.ecn.uiowa.edu/apple2/apple16/Hypermedia/Hypercard/ . ---------------------------- From: Wayne Stewart I've sped up several ZipGS's and always topped out at 12 or 12.5MHz until I replaced the 74F00 on the board with a 74HC00. I'd strongly suggest taking the ZipGS as far as you can with plug-in parts, which'll likely be to about 12MHz; then, give the 74HC00 swap-in some thought. ____________________________ From: Scott G. and Andrew Roughan 020- Do I need new GALs to speed up my TransWarpGS? Probably not. The new 14MHz 65C816's available from WDC make it generally unnecessary to swap in new GAL chips to go to higher speeds. In fact, one user with the faster GALs already installed reports that his TransWarpGS would not work until GAL 3E was replaced with an older GAL 3A. If you are attempting to use an older 65C816-- e.g. a 10MHz chip released in the early 1990's-- then, it may be necessary to upgrade the GALs (especially GAL 3A) to run reliably above 10MHz. Due to variations in boards and parts, about the only way to find out is to experiment. ____________________________ From: Rubywand 021- I have an 8kB TransWarpGS. How does a cache upgrade compare with a speed upgrade? John Link charted some comparisons in 1991 involving nine setups: no-TWGS, and 7, 8, 9, 10mHz boards before and after the 8kB-to-32kB cache upgrade. He used three benchmarks: 1. time to calculate page breaks in a 218-page Appleworks document 2. time to scroll through a 39-page Awks-GS document 3. time to compile 4800 lines of MD-BASIC source code For a 7mHz 8kB TWGS, the speed gain for the 32kB cache upgrade is roughly 33% to nearly x2.5 plain GS speed. For a 10mHz 8kB TWGS, the speed gain for the 32kB cache upgrade is roughly 33% to about x3.25 plain GS speed. His charts shows that a 7mHz TWGS with the 32kB cache performs slightly better than a 10mHz TWGS with 8kB cache on tests 1 and 3; it is a bit slower on test 2. ---------------------------- 022- How can I upgrade my TWGS to 32k cache? SHH Systeme ( http://www.wbwip.com/shh/ ), a German company, sells the cache upgrade piggyback board in various states of 'do-it-yourself' readiness. The ready-to-go version is $69 (+ $14 S&H). It includes three 32K cache RAMs (62256-15 or equivalent) and can support speed upgrades to 14MHz or better. SHH does not automatically include the firmware ROM. If your firmware version is not v1.7 or v1.8, you will also need to order the v1.8 EPROM which SHH sells for $12. ____________________________ From: Scott G., Andrew Roughan, Rubywand 023- How can I upgrade TWGS speed? The process is very similar to that described earlier for the ZipGS. That is, you swap in a new 14MHz 65C816, a higher speed oscillator module, and, possibly, faster 32k x 8 SRAM chips. As mentioned in Q&A 020, you should not have to upgrade to faster GAL chips. Users with the newer GAL 3E in place may actually need to swap in an older GAL 3A. According to a 1992 Appleworks Forum article by John Link, you can get to 12.5MHz with an older 10MHz 65C816, a 50MHz oscillator, and 35ns SRAM without upgrading to the faster GAL chips. As with ZipGS, TransWarpGS speed = Osc Speed divided by 4. One difference is that the TransWarpGS oscillator module is of the "half-size" kind. Another is that, if RAM is upgraded, the usual practice is for all three to have the same speed rating. If you do the SHH cache upgrade, there should be no need to worry about replacing SRAM. TransWarpGS boards vary just as do ZipGS boards. Some can be pushed to higher speeds than others. If you decide to do a speed upgrade, get two or three oscillators to allow for some experimentation. For a step-by-step guide, download Scott G's TWGSupgrade.SHK. HyperCard stack at ftp://ground.ecn.uiowa.edu/apple2/apple16/Hypermedia/Hypercard/ . ---------------------------- From: Wayne Stewart I have a TransWarpGS with rev A GALs and a rev 1.5 ROM. It came as 7mhz with an 8k cache. It was pretty unstable when I recieved it, so I put in a spare 14mhz 65c816 I had which stabilized it. Since I had a lot of rectangular oscillators from my ZipGS upgrade experimenting, I made up an adapter so I could use them in the TransWarp. With those two changes it's running at 14mhz. ---------------------------- From: Andrew Roughan It's time (June 2003) for an update on this article. I have recently purchased some more oscillators from Clarke & Severn Electronics. They can now provide custom programmed oscillators in 1/2 TTL packages for AU$6.98 each. I am currently running my ROM 3 system at 14Mhz. I have a Transwarp GS with ROM 1.8S and the 32k cache from Applied Engineering (35ns SRAMs). The GAL versions are TWGS1A1, TWGS2B1, TWGS3B1, TWGS4B1, TWGS5A1, TWGS6A1, TWGS7A1, TWGS8A1. I have the 14Mhz 65816 available from WDC. I have not purchased faster SRAMs or modified the power supply. ____________________________ From: Rubywand 024- What kind of RAMs do I need for a TWGS or ZipGS speedup? If you upgrade your accelerator RAM, go for fast 32k x 8 Static RAM in a 28-pin Dip package. If your RAM sockets are "skinny" (about as fat as a typical 74xx TTL IC), you want a 300-mil wide package. Otherwise, you will need a 600-mil wide IC or a socket adapter for 300-mil (or do the socket mods described earlier in this FAQ). Fast 600-mil package 32k x 8 SRAMs are fairly rare. However, the IDT71256 is supposed to be available at good speeds (25ns-40ns) in a 600-mil version from Integrated Device Technology. The selection of 300-mil 32k x 8 SRAMs is much larger: Cypress's CY7C199, Hitachi's HM62256, ... . ____________________________ From: Sandy 025- How can I tell the firmware version of my TWGS? With the IIGS turned on, press CONTROL-Apple-ESCAPE And go to the Transwarp CDA The ROM version will be displayed on the screen. ____________________________ From: Mitch Spector 026- Do I need I need the 2B GAL for my Transwarp-GS to use a SCSI interface? If I do, where can I get one? The TWGS-2B GAL was a DMA fix Applied Engineering issued for the board. It is an absolute requirement for Transwarp to work at all with at least some RamFAST SCSI boards (e.g. the revision C boards). With Applied Engineering long since out of business and the GAL virtually impossible to duplicate by convential means, that leaves no good source for replacement GALs. I found it much more affordable (and less hassle) to just purchase a used TransWarp GS board with the 2B GAL to replace your old one. ---------------------------- From: Supertimer RamFAST revision D does not require the 2B GAL. The Apple High Speed SCSI card works with all TransWarps GS units. ____________________________ From: Rubywand 027- When I change my ZipGS's Speed, Misc, and Slot settings via the Zip CDA, they are always lost after turning OFF the GS. What's wrong? Do I need a new BatRAM battery? No. The reason the settings are forgotten is that they are not saved in BatRAM or on-disk. ZipGS settings made via the Zip CDA or via the Zip Control Panel are only in effect for the current session of computing. ---------------------------- 028- What do the check-marks mean next to settings in the ZipGS CDA? Are they original factory settings or what? More like "or what". The check-marks indicate the settings of the DIP switches on your ZipGS board. ---------------------------- 029- After installing my ZipGS along with the ZipGS CDA and other software I've noticed that my ZipGS settings never seem to match the ones I originally set via the on-board DIP switches!? There are two likely explanations. One is that your interpretation of the settings is confused due to the rather poor explanations provided in the Zip on-disk HyperStudio 'manual'. It does not help that names/descriptions of the settings are not quite the same in the 'manual' and in the CDA or NDA. For info on setting your on-board DIP switches, see question 001. Another possibility is that when you installed the ZipGS software, you installed ZipInit in your SYSTEM/SYSTEM.SETUP folder. If you did, then whatever settings ZipInit is set up for will be the settings for your ZipGS after booting. That is, ZipInit will over-ride your DIP switch settings. ZipInit is intended for use on diskettes which, when booted, will set up the ZipGS in some special way to match the software on the diskette. For example, you might want to turn OFF the ZipGS or reduce its speed when booting an arcade games diskette. The cure for unwanted influence from ZipInit is to delete it from your SYSTEM/SYSTEM.SETUP folder. ---------------------------- 030- I have a ZipGS. Usually, it runs like a champ; but, sometimes when I power-ON my GS, I get an all-white screen and the computer just 'hangs'. What's going on? It may be that your ZipGS card is not making good contact in its Slot socket. This is a fairly nasty problem which has led users to pursue a number of false cures. With power OFF, pull your ZipGS board and inspect the bottom-of-card connectors. What you will, most likely, notice is that the connector traces end approximately 1/8 inch or so from the bottom of the card. Unfortunately, the GS Slot sockets make contact rather near the bottom of cards plugged into them-- roughly 1/8 inch or so from the bottom. The reason your GS sometimes hangs is that, sometimes, the ZipGS card is not making good contact with all Slot connectors. One 'cure' is to make sure the ZipGS card's contacts are clean and that the card is thoroughly plugged in-- i.e. well lined-up with Slot contacts and inserted as far as it will go into the Slot socket. A mildly tricky additional step is to use a small jeweller's screwdriver to reach into the Slot socket and _carefully_ twist/pull/bend-out each contact very slightly (naturally, with power OFF). You do not want any contact to normally touch a contact across from it. Whatever, if your GS starts okay and does not exhibit the same kind of hanging in the future, you know that the ZipGS card is well socketed. A more permanent, reliable cure is one _not_ recommended for someone without experience working on circuit boards: You find a better Slot connector socket-- one with gold contacts which touch plugged-in cards higher up and with circuit board connections which will fit into the original holes-- and replace the connector. This is a _very_ tricky replacement which requires careful de-soldering of the original Slot socket, cleaning of contact holes, and soldering-on the new socket-- all without burning the circuit board or slicing traces on either side. Actually, slicing traces is okay, IF you are prepared to repair the damage. (Yes; I did this replacement on our GS. It works; but, If I had known what a hassle it would be, I probably would never have done it!) ---------------------------- 031- Ever since my accelerator speed upgrade it seems like my GS is always experiencing random system crashes. What's the problem and how can I fix it? When a GS equipped with an accelerator experiences frequent crashes into the monitor after a speed upgrade, the usual explanations are ... 1. the accelerator is over-clocked for the microprocessor or RAM; 2. there are serious noise spikes on the Slot power lines. If you are 'pushing' your current RAM or using an old 65C816, you can upgrade to faster chips or swap in a slower oscillator. Often, the problem will be noise spikes related to increased current load and/or increased sensitivity to noise related to faster clocking. See the POWER FAQs for Power Supply and motherboard mods which should help. ---------------------------- 032- I added a new accelerator board to my Apple and now my system is constantly bombing. What's the problem and how can I fix it? Most likely, the accelerator board's current load has led to increased noise on the +5V bus. See the POWER FAQs for Power Supply and motherboard mods which should help. ---------------------------- 033- How can I get a display of IIgs speed? You can use SpeedGS. This is a STARTUP program selector for ProDOS-8 on the Apple IIgs which features display of Boot Volume, Date/Time, and current Speed. Speed is shown as a rounded multiple of 'Normal'-- i.e. 1MHz. For download sites, see Csa21MAIN4.txt .