SEAGATE TECHNOLOGY, INC. Customer Technical Support FAX Network +1 408 438-8137 Customer Technical Support Bulletin Boards (300-9600, 8-N-1) ��������������������������������������������������������������������Ŀ � United States +1 408 438-8771 � United Kingdom +44 628 478011 � ��������������������������������������������������������������������Ĵ � Germany +49 89 140-9331 � Singapore +65 227-2217 � ���������������������������������������������������������������������� (C)opyright 1993 ST-1830N SCSI-2 Fast �����������ͻ � REAR VIEW � �����������ͼ 50 pin I/O Cable Connection � J1�������������������������1� /���������\ TOP (HDA) ͵:::::::::::::::::::::::::�ͳ 0 0 0 0 ��� �������������������������; ��5�G�G�12� BOTTOM 1�����Ŀ 1�����Ŀ 1�����Ŀ �������� �������� �������� �Terminating Resistors� �����������������ͻ � RIGHT SIDE VIEW � �����������������ͼ BACK �͸ J2 12345678 TOP (HDA) FRONT OF J1�����������������������P�W�A����������������������� OF DRIVE �; :::::::: BOTTOM DRIVE �������� �Terminator Power ٳ������ Reserved ڴTerminator Power �ٳ����� Start Delay (12 secs * ID) � Factory Use ��ٳ���� Motor Start � Parity Enable �������� Write Protect � � � ��������������������������������Ŀ �Ĵ Termination Power-source Table � ����������������������������������������������Ŀ ������....�����....�����PWA edge����� � � � � 1 2 1 2 1 2 � � �ķ �ķ A Drive Supplies Bus � � ���� ���� ����� B Drive Supplies Own � � ���� ���� �� �� C Bus Supplies Drive � � A B C � ����������Default������������������������������� ����������������ͻ � LEFT SIDE VIEW � ����������������ͼ If these ID jumpers are used, then ID jumpers shown in front view ARE NOT USED. FRONT TOP (HDA) J5 ���1� �͸BACK OF ��������P�W�A������������������������������͵:::�͵J1 OF DRIVE BOTTOM ���; �;DRIVE ��� Note: On early drives � ID 1 �ٳ�� ID 4 with PCB# 75782395 or � ID 2 #75782485 ID jumpers are��� ID 4 ID 1 reversed. � ������������ͻ � FRONT VIEW � ������������ͼ TOP (HDA) J6 ������1� ��P�W�A�������������������������͵::::::�� * BOTTOM ������; � 123456 LED �� ������ ID 4 ٳ���� Reserved ID 2 �ٳ��� Remote LED (pin-3 +5v) ID 1 ������ Spindle Synchronization (pin-6 REF SIG+) If these ID jumper are used, then ID jumpers shown in left side view ARE NOT USED. ST - 1830N UNFORMATTED CAPACITY (MB) ________________834 FORMATTED CAPACITY (xx SECTORS) (MB) _____702 AVERAGE SECTORS PER TRACK ________________79 ACTUATOR TYPE ____________________________VOICE COIL TRACKS ___________________________________17,225 CYLINDERS ________________________________1,325 (user) HEADS ____________________________________13 DISCS (3.5 in) ___________________________7 MEDIA TYPE _______________________________THIN FILM RECORDING METHOD _________________________ZBR RLL (1,7) INTERNAL TRANSFER RATE (mbits/sec) _______28.4 to 41.2 EXTERNAL TRANSFER RATE (mbyte/sec) _______4 Async EXTERNAL TRANSFER RATE (mbyte/sec) _______10 Sync SPINDLE SPEED (RPM) ______________________4,535 AVERAGE LATENCY (mSEC) ___________________6.61 BUFFER ___________________________________256 Kbyte Read Look-Ahead, Adaptive, Multi-Segmented Cache INTERFACE ________________________________SCSI-2 Fast BYTES PER TRACK __________________________48,419 avg. TPI (TRACKS PER INCH) ____________________2,150 AVERAGE ACCESS (ms) (read/write)__________TBD Drive level without controller overhead SINGLE TRACK SEEK (ms) ___________________TBD MAX FULL SEEK (ms) _______________________TBD MTBF (power-on hours) ____________________200,000 POWER REQUIREMENTS: +12V START-UP (amps) _2.0 +12V TYPICAL (amps) __0.5 +5V TYPICAL (amps) ___0.4 TYPICAL (watts) ______11 IDLE (watts) _________9 LANDING ZONE (cyl)________________________AUTO PARK IBM AT DRIVE TYPE ________________________0 or NONE Already low-level formatted at the factory. ZBR = Zone Bit Recording = Variable sectors per track Formatted at the factory with 1 spare sector per track and two spare cylinders at inner tracks per unit. Seagate reserves the right to change, without notice, product offerings or specifications. (10/12/93)