💾 Archived View for gmi.noulin.net › man › man2 › read.2.gmi captured on 2024-08-31 at 13:40:19. Gemini links have been rewritten to link to archived content

View Raw

More Information

⬅️ Previous capture (2022-06-12)

-=-=-=-=-=-=-

READ(2)                                                                 Linux Programmer's Manual                                                                READ(2)

NAME
       read - read from a file descriptor

SYNOPSIS
       #include <unistd.h>

       ssize_t read(int fd, void *buf, size_t count);

DESCRIPTION
       read() attempts to read up to count bytes from file descriptor fd into the buffer starting at buf.

       On files that support seeking, the read operation commences at the file offset, and the file offset is incremented by the number of bytes read.  If the file off‐
       set is at or past the end of file, no bytes are read, and read() returns zero.

       If count is zero, read() may detect the errors described below.  In the absence of any errors, or if read() does not check for errors, a read() with a count of 0
       returns zero and has no other effects.

       According to POSIX.1, if count is greater than SSIZE_MAX, the result is implementation-defined; see NOTES for the upper limit on Linux.

RETURN VALUE
       On success, the number of bytes read is returned (zero indicates end of file), and the file position is advanced by this number.  It is not an error if this num‐
       ber is smaller than the number of bytes requested; this may happen for example because fewer bytes are actually available right now (maybe because we were  close
       to end-of-file, or because we are reading from a pipe, or from a terminal), or because read() was interrupted by a signal.  See also NOTES.

       On error, -1 is returned, and errno is set to indicate the error.  In this case, it is left unspecified whether the file position (if any) changes.

ERRORS
       EAGAIN The  file descriptor fd refers to a file other than a socket and has been marked nonblocking (O_NONBLOCK), and the read would block.  See open(2) for fur‐
              ther details on the O_NONBLOCK flag.

       EAGAIN or EWOULDBLOCK
              The file descriptor fd refers to a socket and has been marked nonblocking (O_NONBLOCK), and the read would block.  POSIX.1-2001 allows either error to  be
              returned for this case, and does not require these constants to have the same value, so a portable application should check for both possibilities.

       EBADF  fd is not a valid file descriptor or is not open for reading.

       EFAULT buf is outside your accessible address space.

       EINTR  The call was interrupted by a signal before any data was read; see signal(7).

       EINVAL fd  is  attached to an object which is unsuitable for reading; or the file was opened with the O_DIRECT flag, and either the address specified in buf, the
              value specified in count, or the file offset is not suitably aligned.

       EINVAL fd was created via a call to timerfd_create(2) and the wrong size buffer was given to read(); see timerfd_create(2) for further information.

       EIO    I/O error.  This will happen for example when the process is in a background process group, tries to read from its controlling terminal, and either it  is
              ignoring  or  blocking SIGTTIN or its process group is orphaned.  It may also occur when there is a low-level I/O error while reading from a disk or tape.
              A further possible cause of EIO on networked filesystems is when an advisory lock had been taken out on the file descriptor and this lock has  been  lost.
              See the Lost locks section of fcntl(2) for further details.

       EISDIR fd refers to a directory.

       Other errors may occur, depending on the object connected to fd.

CONFORMING TO
       SVr4, 4.3BSD, POSIX.1-2001.

NOTES
       The types size_t and ssize_t are, respectively, unsigned and signed integer data types specified by POSIX.1.

       On Linux, read() (and similar system calls) will transfer at most 0x7ffff000 (2,147,479,552) bytes, returning the number of bytes actually transferred.  (This is
       true on both 32-bit and 64-bit systems.)

       On NFS filesystems, reading small amounts of data will update the timestamp only the first time, subsequent calls may not do so.  This is caused by  client  side
       attribute  caching,  because  most  if not all NFS clients leave st_atime (last file access time) updates to the server, and client side reads satisfied from the
       client's cache will not cause st_atime updates on the server as there are no server-side reads.  UNIX semantics can be obtained by disabling  client-side  attri‐
       bute caching, but in most situations this will substantially increase server load and decrease performance.

BUGS
       According to POSIX.1-2008/SUSv4 Section XSI 2.9.7 ("Thread Interactions with Regular File Operations"):

           All of the following functions shall be atomic with respect to each other in the effects specified in POSIX.1-2008 when they operate on regular files or sym‐
           bolic links: ...

       Among the APIs subsequently listed are read() and readv(2).  And among the effects that should be atomic across threads (and processes) are updates of  the  file
       offset.   However,  on  Linux before version 3.14, this was not the case: if two processes that share an open file description (see open(2)) perform a read() (or
       readv(2)) at the same time, then the I/O operations were not atomic with respect updating the file offset, with the result that the reads in  the  two  processes
       might (incorrectly) overlap in the blocks of data that they obtained.  This problem was fixed in Linux 3.14.

SEE ALSO
       close(2), fcntl(2), ioctl(2), lseek(2), open(2), pread(2), readdir(2), readlink(2), readv(2), select(2), write(2), fread(3)

Linux                                                                          2021-03-22                                                                        READ(2)