💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc5046.txt captured on 2024-06-16 at 17:03:55.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group M. Ko
Request for Comments: 5046 IBM Corporation
Category: Standards Track M. Chadalapaka
Hewlett-Packard Company
J. Hufferd
Brocade, Inc.
U. Elzur
H. Shah
P. Thaler
Broadcom Corporation
October 2007
Internet Small Computer System Interface (iSCSI) Extensions
for Remote Direct Memory Access (RDMA)
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Abstract
Internet Small Computer System Interface (iSCSI) Extensions for
Remote Direct Memory Access (RDMA) provides the RDMA data transfer
capability to iSCSI by layering iSCSI on top of an RDMA-Capable
Protocol, such as the iWARP protocol suite. An RDMA-Capable Protocol
provides RDMA Read and Write services, which enable data to be
transferred directly into SCSI I/O Buffers without intermediate data
copies. This document describes the extensions to the iSCSI protocol
to support RDMA services as provided by an RDMA-Capable Protocol,
such as the iWARP protocol suite.
Ko, et al. Standards Track [Page 1]
RFC 5046 iSER Specification October 2007
Table of Contents
1. Introduction ....................................................5
1.1. Motivation .................................................5
1.2. Architectural Goals ........................................6
1.3. Protocol Overview ..........................................7
1.4. RDMA Services and iSER .....................................8
1.4.1. STag ................................................8
1.4.2. Send ................................................9
1.4.3. RDMA Write ..........................................9
1.4.4. RDMA Read ...........................................9
1.5. SCSI Read Overview ........................................10
1.6. SCSI Write Overview .......................................10
1.7. iSCSI/iSER Layering .......................................10
2. Definitions and Acronyms .......................................11
2.1. Definitions ...............................................11
2.2. Acronyms ..................................................17
2.3. Conventions ...............................................19
3. Upper Layer Interface Requirements .............................19
3.1. Operational Primitives Offered by iSER ....................20
3.1.1. Send_Control .......................................20
3.1.2. Put_Data ...........................................20
3.1.3. Get_Data ...........................................21
3.1.4. Allocate_Connection_Resources ......................21
3.1.5. Deallocate_Connection_Resources ....................22
3.1.6. Enable_Datamover ...................................22
3.1.7. Connection_Terminate ...............................22
3.1.8. Notice_Key_Values ..................................23
3.1.9. Deallocate_Task_Resources ..........................23
3.2. Operational Primitives Used by iSER .......................23
3.2.1. Control_Notify .....................................24
3.2.2. Data_Completion_Notify .............................24
3.2.3. Data_ACK_Notify ....................................24
3.2.4. Connection_Terminate_Notify ........................25
3.3. iSCSI Protocol Usage Requirements .........................25
4. Lower Layer Interface Requirements .............................26
4.1. Interactions with the RCaP Layer ..........................26
4.2. Interactions with the Transport Layer .....................27
5. Connection Setup and Termination ...............................27
5.1. iSCSI/iSER Connection Setup ...............................27
5.1.1. Initiator Behavior .................................29
5.1.2. Target Behavior ....................................30
5.1.3. iSER Hello Exchange ................................32
5.2. iSCSI/iSER Connection Termination .........................33
5.2.1. Normal Connection Termination at the Initiator .....33
5.2.2. Normal Connection Termination at the Target ........34
5.2.3. Termination without Logout Request/Response PDUs ...34
Ko, et al. Standards Track [Page 2]
RFC 5046 iSER Specification October 2007
6. Login/Text Operational Keys ....................................35
6.1. HeaderDigest and DataDigest ...............................35
6.2. MaxRecvDataSegmentLength ..................................36
6.3. RDMAExtensions ............................................36
6.4. TargetRecvDataSegmentLength ...............................37
6.5. InitiatorRecvDataSegmentLength ............................38
6.6. OFMarker and IFMarker .....................................38
6.7. MaxOutstandingUnexpectedPDUs ..............................38
7. iSCSI PDU Considerations .......................................39
7.1. iSCSI Data-Type PDU .......................................39
7.2. iSCSI Control-Type PDU ....................................40
7.3. iSCSI PDUs ................................................40
7.3.1. SCSI Command .......................................40
7.3.2. SCSI Response ......................................42
7.3.3. Task Management Function Request/Response ..........44
7.3.4. SCSI Data-Out ......................................45
7.3.5. SCSI Data-In .......................................46
7.3.6. Ready to Transfer (R2T) ............................48
7.3.7. Asynchronous Message ...............................50
7.3.8. Text Request and Text Response .....................50
7.3.9. Login Request and Login Response ...................50
7.3.10. Logout Request and Logout Response ................51
7.3.11. SNACK Request .....................................51
7.3.12. Reject ............................................51
7.3.13. NOP-Out and NOP-In ................................51
8. Flow Control and STag Management ...............................52
8.1. Flow Control for RDMA Send Message Types ..................52
8.1.1. Flow Control for Control-Type PDUs from the
Initiator ..........................................52
8.1.2. Flow Control for Control-Type PDUs from the
Target .............................................55
8.2. Flow Control for RDMA Read Resources ......................56
8.3. STag Management ...........................................56
8.3.1. Allocation of STags ................................57
8.3.2. Invalidation of STags ..............................57
9. iSER Control and Data Transfer .................................58
9.1. iSER Header Format ........................................58
9.2. iSER Header Format for the iSCSI Control-Type PDU .........59
9.3. iSER Header Format for the iSER Hello Message .............60
9.4. iSER Header Format for the iSER HelloReply Message ........61
9.5. SCSI Data Transfer Operations .............................62
9.5.1. SCSI Write Operation ...............................62
9.5.2. SCSI Read Operation ................................63
9.5.3. Bidirectional Operation ............................64
10. iSER Error Handling and Recovery ..............................64
10.1. Error Handling ...........................................64
10.1.1. Errors in the Transport Layer .....................64
10.1.2. Errors in the RCaP Layer ..........................65
Ko, et al. Standards Track [Page 3]
RFC 5046 iSER Specification October 2007
10.1.3. Errors in the iSER Layer ..........................66
10.1.4. Errors in the iSCSI Layer .........................67
10.2. Error Recovery ...........................................69
10.2.1. PDU Recovery ......................................69
10.2.2. Connection Recovery ...............................70
11. Security Considerations .......................................71
12. References ....................................................71
12.1. Normative References .....................................71
12.2. Informative References ...................................72
Appendix A. iWARP Message Format for iSER .........................73
A.1. iWARP Message Format for iSER Hello Message ...............73
A.2. iWARP Message Format for iSER HelloReply Message ..........74
A.3. iWARP Message Format for SCSI Read Command PDU ............75
A.4. iWARP Message Format for SCSI Read Data ...................76
A.5. iWARP Message Format for SCSI Write Command PDU ...........77
A.6. iWARP Message Format for RDMA Read Request ................78
A.7. iWARP Message Format for Solicited SCSI Write Data ........79
A.8. iWARP Message Format for SCSI Response PDU ................80
Appendix B. Architectural Discussion of iSER over InfiniBand ......81
B.1. The Host Side of the iSCSI and iSER Connections
in InfiniBand .............................................81
B.2. The Storage Side of the iSCSI and iSER Mixed
Network Environment .......................................82
B.3. Discovery Processes for an InfiniBand Host ................82
B.4. IBTA Connection Specifications ............................83
Acknowledgments ...................................................83
Table of Figures
Figure 1. Example of iSCSI/iSER Layering in Full Feature Phase ....11
Figure 2. iSER Header Format ......................................58
Figure 3. iSER Header Format for iSCSI Control-Type PDU ...........59
Figure 4. iSER Header Format for iSER Hello Message ...............60
Figure 5. iSER Header Format for iSER HelloReply Message ..........61
Figure 6. SendSE Message containing an iSER Hello Message .........72
Figure 7. SendSE Message containing an iSER HelloReply Message ....74
Figure 8. SendSE Message containing a SCSI Read Command PDU .......75
Figure 9. RDMA Write Message containing SCSI Read Data ............76
Figure 10. SendSE Message containing a SCSI Write Command PDU .....77
Figure 11. RDMA Read Request Message ..............................78
Figure 12. RDMA Read Response Message containing SCSI Write Data ..79
Figure 13. SendInvSE Message containing SCSI Response PDU .........80
Figure 14. iSCSI and iSER on IB ...................................81
Figure 15. Storage Controller with TCP, iWARP, and IB Connections .82
Ko, et al. Standards Track [Page 4]
RFC 5046 iSER Specification October 2007
1. Introduction
1.1. Motivation
The iSCSI protocol [RFC3720] is a mapping of the SCSI Architecture
Model (see [SAM2]) over the TCP protocol. SCSI commands are carried
by iSCSI requests, and SCSI responses and status are carried by iSCSI
responses. Other iSCSI protocol exchanges and SCSI data are also
transported in iSCSI Protocol Data Units (PDUs).
Out-of-order TCP segments in the Traditional iSCSI model have to be
stored and reassembled before the iSCSI protocol layer within an end
node can place the data in the iSCSI buffers. This reassembly is
required because not every TCP segment is likely to contain an iSCSI
header to enable its placement, and TCP itself does not have a
built-in mechanism for signaling Upper Level Protocol (ULP) message
boundaries to aid placement of out-of-order segments. This TCP
reassembly at high network speeds is quite counter-productive for the
following reasons: wasted memory bandwidth in data copying, the need
for reassembly memory, wasted CPU cycles in data copying, and the
general store-and-forward latency from an application perspective.
TCP reassembly was recognized as a serious issue in [RFC3720], and
the notion of a "sync and steering layer" was introduced that is
optional to implement and use. One specific sync and steering
mechanism, called "markers", was defined in [RFC3720], which provides
an application-level way of framing iSCSI Protocol Data Units (PDUs)
within the TCP data stream even when the TCP segments are not yet
reassembled to be in-order.
With these defined techniques in [RFC3720], a Network Interface
Controller customized for iSCSI (SNIC) could offload the TCP/IP
processing and support direct data placement, but most iSCSI
implementations do not support iSCSI "markers", making SNIC marker-
based direct data placement unusable in practice.
The iWARP protocol stack provides direct data placement functionality
that is usable in practice. In addition, there is interest in using
iSCSI with other Remote Direct Memory Access (RDMA) protocol stacks
that support direct data placement, such as the one provided by
InfiniBand. The generic term RDMA-Capable Protocol (RCaP) is used to
refer to the RDMA functionality provided by such protocol stacks.
With the availability of RDMA-Capable Controllers within a host
system, which does not have SNICs, it is appropriate for iSCSI to be
able to exploit the direct data placement function of the RDMA-
Capable Controller like other applications.
Ko, et al. Standards Track [Page 5]
RFC 5046 iSER Specification October 2007
iSCSI Extensions for RDMA (iSER) is designed precisely to take
advantage of generic RDMA technologies -- iSER's goal is to permit
iSCSI to employ direct data placement and RDMA capabilities using a
generic RDMA-Capable Controller. In summary, the iSCSI/iSER protocol
stack is designed to enable scaling to high speeds by relying on a
generic data placement process and RDMA technologies and products,
which enable direct data placement of both in-order and out-of-order
data.
This document describes iSER as a protocol extension to iSCSI, both
for convenience of description and because it is true in a very
strict protocol sense. However, note that iSER is in reality
extending the connectivity of the iSCSI protocol defined in
[RFC3720], and the name iSER reflects this reality.
When the iSCSI protocol as defined in [RFC3720] (i.e., without the
iSER enhancements) is intended in the rest of the document, the term
"Traditional iSCSI" is used to make the intention clear.
1.2. Architectural Goals
This section summarizes the architectural goals that guided the
design of iSER.
1. Provide an RDMA data transfer model for iSCSI that enables direct
in-order or out-of-order data placement of SCSI data into pre-
allocated SCSI buffers while maintaining in-order data delivery.
2. Not require any major changes to the SCSI Architecture Model
[SAM2] and SCSI command set standards.
3. Utilize existing iSCSI infrastructure (sometimes referred to as
"iSCSI ecosystem") including but not limited to MIB,
bootstrapping, negotiation, naming and discovery, and security.
4. Require a session to operate in the Traditional iSCSI data
transfer mode if iSER is not supported by either the initiator or
the target (i.e., not require iSCSI Full Feature Phase
interoperability between an end node operating in Traditional
iSCSI mode, and an end node operating in iSER-assisted mode).
5. Allow initiator and target implementations to utilize generic
RDMA-Capable Controllers such as RDMA-enabled Network Interface
Controllers (RNICs), or to implement iSCSI and iSER in software
(not require iSCSI- or iSER-specific assists in the RCaP
implementation or RDMA-Capable Controller).
Ko, et al. Standards Track [Page 6]
RFC 5046 iSER Specification October 2007
6. Require full and only generic RCaP functionality at both the
initiator and the target.
7. Implement a lightweight Datamover protocol for iSCSI with minimal
state maintenance.
1.3. Protocol Overview
Consistent with the architectural goals stated in Section 2.2, the
iSER protocol does not require changes in the iSCSI ecosystem or any
related SCSI specifications. The iSER protocol defines the mapping
of iSCSI PDUs to RCaP Messages in such a way that it is entirely
feasible to realize iSCSI/iSER implementations that are based on
generic RDMA-Capable Controllers. The iSER protocol layer requires
minimal state maintenance to assist an iSCSI Full Feature Phase
connection, besides being oblivious to the notion of an iSCSI
session. The crucial protocol aspects of iSER may be summarized
thus:
1. iSER-assisted mode is negotiated during the iSCSI login for each
session, and an entire iSCSI session can only operate in one mode
(i.e., a connection in a session cannot operate in iSER-assisted
mode if a different connection of the same session is already in
Full Feature Phase in the Traditional iSCSI mode).
2. Once in iSER-assisted mode, all iSCSI interactions on that
connection use RCaP Messages.
3. A Send Message Type is used for carrying an iSCSI control-type PDU
preceded by an iSER header. See Section 7.2 for more details on
iSCSI control-type PDUs.
4. RDMA Write, RDMA Read Request, and RDMA Read Response Messages are
used for carrying control and all data information associated with
the iSCSI data-type PDUs. See Section 7.1 for more details on
iSCSI data-type PDUs.
5. Target drives all data transfer (with the exception of iSCSI
unsolicited data) for SCSI writes and SCSI reads, by issuing RDMA
Read Requests and RDMA Writes, respectively.
6. RCaP is responsible for ensuring data integrity. (For example,
iWARP includes a CRC-enhanced framing layer called Marker PDU
Aligned Framing for TCP (MPA) on top of TCP; and for InfiniBand,
the CRCs are included in the Reliable Connection mode). For this
reason, iSCSI header and data digests are negotiated to "None" for
iSCSI/iSER sessions.
Ko, et al. Standards Track [Page 7]
RFC 5046 iSER Specification October 2007
7. The iSCSI error recovery hierarchy defined in [RFC3720] is fully
supported by iSER. (However, see Section 7.3.11 on the handling
of SNACK Request PDUs.)
8. iSER requires no changes to iSCSI authentication, security, and
text mode negotiation mechanisms.
Note that Traditional iSCSI implementations may have to be adapted to
employ iSER. It is expected that the adaptation when required is
likely to be centered around the upper layer interface requirements
of iSER (Section 3).
1.4. RDMA Services and iSER
iSER is designed to work with software and/or hardware protocol
stacks providing the protocol services defined in RCaP documents such
as [RDMAP], [IB], etc. The following subsections describe the key
protocol elements of RCaP services that iSER relies on.
1.4.1. STag
A Steering Tag (STag) is the identifier of an I/O Buffer unique to an
RDMA-Capable Controller that the iSER layer Advertises to the remote
iSCSI/iSER node in order to complete a SCSI I/O.
In iSER, Advertisement is the act of informing the target by the
initiator that an I/O Buffer is available at the initiator for RDMA
Read or RDMA Write access by the target. The initiator Advertises
the I/O Buffer by including the STag in the header of an iSER Message
containing the SCSI Command PDU to the target. The base Tagged
Offset is not explicitly specified, but the target must always assume
it as zero. The buffer length is as specified in the SCSI Command
PDU.
The iSER layer at the initiator Advertises the STag for the I/O
Buffer of each SCSI I/O to the iSER layer at the target in the iSER
header of the Send with Solicited Event (SendSE) Message containing
the SCSI Command PDU, unless the I/O can be completely satisfied by
unsolicited data alone.
The iSER layer at the target provides the STag for the I/O Buffer
that is the Data Sink of an RDMA Read Operation (Section 2.4.4) to
the RCaP layer on the initiator node -- i.e., this is completely
transparent to the iSER layer at the initiator.
The iSER protocol is defined so that the Advertised STag is
automatically invalidated upon a normal completion of the associated
task. This automatic invalidation is realized via the Send with
Ko, et al. Standards Track [Page 8]
RFC 5046 iSER Specification October 2007
Solicited Event and Invalidate (SendInvSE) Message carrying the SCSI
Response PDU. There are two exceptions to this automatic
invalidation -- bidirectional commands, and abnormal completion of a
command. The iSER layer at the initiator is required to explicitly
invalidate the STag in these cases, in addition to sanity checking
the automatic invalidation even when that does happen.
1.4.2. Send
Send is the RDMA Operation that is not addressed to an Advertised
buffer by the sending side, and thus uses Untagged buffers on the
receiving side.
The iSER layer at the initiator uses the Send Operation to transmit
any iSCSI control-type PDU to the target. As an example, the
initiator uses Send Operations to transfer iSER Messages containing
SCSI Command PDUs to the iSER layer at the target.
An iSER layer at the target uses the Send Operation to transmit any
iSCSI control-type PDU to the initiator. As an example, the target
uses Send Operations to transfer iSER Messages containing SCSI
Response PDUs to the iSER layer at the initiator.
1.4.3. RDMA Write
RDMA Write is the RDMA Operation that is used to place data into an
Advertised buffer on the receiving side. The sending side addresses
the Message using an STag and a Tagged Offset that are valid on the
Data Sink.
The iSER layer at the target uses the RDMA Write Operation to
transfer the contents of a local I/O Buffer to an Advertised I/O
Buffer at the initiator. The iSER layer at the target uses the RDMA
Write to transfer whole or part of the data required to complete a
SCSI read command.
The iSER layer at the initiator does not employ RDMA Writes.
1.4.4. RDMA Read
RDMA Read is the RDMA Operation that is used to retrieve data from an
Advertised buffer on a remote node. The sending side of the RDMA
Read Request addresses the Message using an STag and a Tagged Offset
that are valid on the Data Source in addition to providing a valid
local STag and Tagged Offset that identify the Data Sink.
The iSER layer at the target uses the RDMA Read Operation to transfer
the contents of an Advertised I/O Buffer at the initiator to a local
Ko, et al. Standards Track [Page 9]
RFC 5046 iSER Specification October 2007
I/O Buffer at the target. The iSER layer at the target uses the RDMA
Read to fetch whole or part of the data required to complete a SCSI
write command.
The iSER layer at the initiator does not employ RDMA Reads.
1.5. SCSI Read Overview
The iSER layer at the initiator receives the SCSI Command PDU from
the iSCSI layer. The iSER layer at the initiator generates an STag
for the I/O Buffer of the SCSI Read and Advertises the buffer by
including the STag as part of the iSER header for the PDU. The iSER
Message is transferred to the target using a SendSE Message.
The iSER layer at the target uses one or more RDMA Writes to transfer
the data required to complete the SCSI Read.
The iSER layer at the target uses a SendInvSE Message to transfer the
SCSI Response PDU back to the iSER layer at the initiator. The iSER
layer at the initiator notifies the iSCSI layer of the availability
of the SCSI Response PDU.
1.6. SCSI Write Overview
The iSER layer at the initiator receives the SCSI Command PDU from
the iSCSI layer. If solicited data transfer is involved, the iSER
layer at the initiator generates an STag for the I/O Buffer of the
SCSI Write and Advertises the buffer by including the STag as part of
the iSER header for the PDU. The iSER Message is transferred to the
target using a SendSE Message.
The iSER layer at the initiator may optionally send one or more non-
immediate unsolicited data PDUs to the target using Send Message
Types.
If solicited data transfer is involved, the iSER layer at the target
uses one or more RDMA Reads to transfer the data required to complete
the SCSI Write.
The iSER layer at the target uses a SendInvSE Message to transfer the
SCSI Response PDU back to the iSER layer at the initiator. The iSER
layer at the initiator notifies the iSCSI layer of the availability
of the SCSI Response PDU.
1.7. iSCSI/iSER Layering
iSCSI Extensions for RDMA (iSER) is layered between the iSCSI layer
and the RCaP layer. Note that the RCaP layer may be composed of one
Ko, et al. Standards Track [Page 10]
RFC 5046 iSER Specification October 2007
or more distinct protocol layers depending on the specifics of the
RCaP. Figure 1 shows an example of the relationship between SCSI,
iSCSI, iSER, and the different RCaP layers. For TCP, the RCaP is
iWARP. For InfiniBand, the RCaP is the Reliable Connected Transport
Service. Note that the iSCSI layer as described here supports the
RDMA Extensions as used in iSER.
+-------------------------------------+
| SCSI |
+-------------------------------------+
| iSCSI |
DI ------> +-------------------------------------+
| iSER |
+---------+--------------+------------+
| RDMAP | | |
+---------+ InfiniBand | |
| DDP | Reliable | Other |
+---------+ Connected | RDMA- |
| MPA | Transport | Capable |
+---------+ Service | Protocol |
| TCP | | |
+---------+--------------+------------+
| | InfiniBand | Other |
| IP | Network | Network |
| | Layer | Layer |
+---------+--------------+------------+
Figure 1. Example of iSCSI/iSER Layering in Full Feature Phase
2. Definitions and Acronyms
2.1. Definitions
Advertisement (Advertised, Advertise, Advertisements, Advertises) -
The act of informing a remote iSER layer that a local node's
buffer is available to it. A Node makes a buffer available for
incoming RDMA Read Request Message or incoming RDMA Write Message
access by informing the remote iSER layer of the Tagged Buffer
identifiers (STag, TO, and buffer length). Note that this
Advertisement of Tagged Buffer information is the responsibility
of the iSER layer on either end and is not defined by the RDMA-
Capable Protocol. A typical method would be for the iSER layer to
embed the Tagged Buffer's STag, TO, and buffer length in a Send
Message destined for the remote iSER layer.
Completion (Completed, Complete, Completes) - Completion is defined
as the process by the RDMA-Capable Protocol layer to inform the
Ko, et al. Standards Track [Page 11]
RFC 5046 iSER Specification October 2007
iSER layer, that a particular RDMA Operation has performed all
functions specified for the RDMA Operation.
Connection - A connection is a logical circuit between the initiator
and the target, e.g., a TCP connection. Communication between the
initiator and the target occurs over one or more connections. The
connections carry control messages, SCSI commands, parameters, and
data within iSCSI Protocol Data Units (iSCSI PDUs).
Connection Handle - An information element that identifies the
particular iSCSI connection and is unique for a given iSCSI-iSER
pair. Every invocation of an Operational Primitive is qualified
with the Connection Handle.
Data Sink - The peer receiving a data payload. Note that the Data
Sink can be required to both send and receive RCaP Messages to
transfer a data payload.
Data Source - The peer sending a data payload. Note that the Data
Source can be required to both send and receive RCaP Messages to
transfer a data payload.
Datamover Interface (DI) - The interface between the iSCSI layer and
the Datamover layer as described in [DA].
Datamover Layer - A layer that is directly below the iSCSI layer and
above the underlying transport layers. This layer exposes and
uses a set of transport independent Operational Primitives for the
communication between the iSCSI layer and itself. The Datamover
layer, operating in conjunction with the transport layers, moves
the control and data information on the iSCSI connection. In this
specification, the iSER layer is the Datamover layer.
Datamover Protocol - A Datamover protocol is the wire-protocol that
is defined to realize the Datamover layer functionality. In this
specification, the iSER protocol is the Datamover protocol.
Event - An indication provided by the RDMA-Capable Protocol layer to
the iSER layer to indicate a Completion or other condition
requiring immediate attention.
Inbound RDMA Read Queue Depth (IRD) - The maximum number of incoming
outstanding RDMA Read Requests that the RDMA-Capable Controller
can handle on a particular RCaP Stream at the Data Source. For
some RDMA-Capable Protocol layers, the term "IRD" may be known by
a different name. For example, for InfiniBand, the equivalent for
IRD is the Responder Resources.
Ko, et al. Standards Track [Page 12]
RFC 5046 iSER Specification October 2007
Invalidate STag - A mechanism used to prevent the Remote Peer from
reusing a previous explicitly Advertised STag, until the iSER
layer at the local node makes it available through a subsequent
explicit Advertisement.
I/O Buffer - A buffer that is used in a SCSI Read or Write operation
so SCSI data may be sent from or received into that buffer.
iSCSI - The iSCSI protocol as defined in [RFC3720] is a mapping of
the SCSI Architecture Model of SAM-2 over TCP.
iSCSI control-type PDU - Any iSCSI PDU that is not an iSCSI data-
type PDU and also not a SCSI Data-out PDU carrying solicited data
is defined as an iSCSI control-type PDU. Specifically, it is to
be noted that SCSI Data-out PDUs for unsolicited data are defined
as iSCSI control-type PDUs.
iSCSI data-type PDU - An iSCSI data-type PDU is defined as an iSCSI
PDU that causes data transfer, transparent to the remote iSCSI
layer, to take place between the peer iSCSI nodes on a Full
Feature Phase iSCSI connection. An iSCSI data-type PDU, when
requested for transmission by the sender iSCSI layer, results in
the associated data transfer without the participation of the
remote iSCSI layer, i.e. the PDU itself is not delivered as-is to
the remote iSCSI layer. The following iSCSI PDUs constitute the
set of iSCSI data-type PDUs - SCSI Data-In PDU and R2T PDU.
iSCSI Layer - A layer in the protocol stack implementation within an
end node that implements the iSCSI protocol and interfaces with
the iSER layer via the Datamover Interface.
iSCSI PDU (iSCSI Protocol Data Unit) - The iSCSI layer at the
initiator and the iSCSI layer at the target divide their
communications into messages. The term "iSCSI protocol data unit"
(iSCSI PDU) is used for these messages.
iSCSI/iSER Connection - An iSER-assisted iSCSI connection.
iSCSI/iSER Session - An iSER-assisted iSCSI session.
iSCSI-iSER Pair - The iSCSI layer and the underlying iSER layer.
iSER - iSCSI Extensions for RDMA, the protocol defined in this
document.
iSER-assisted - A term generally used to describe the operation of
iSCSI when the iSER functionality is also enabled below the iSCSI
layer for the specific iSCSI/iSER connection in question.
Ko, et al. Standards Track [Page 13]
RFC 5046 iSER Specification October 2007
iSER-IRD - This variable represents the maximum number of incoming
outstanding RDMA Read Requests that the iSER layer at the
initiator declares on a particular RCaP Stream.
iSER-ORD - This variable represents the maximum number of outstanding
RDMA Read Requests that the iSER layer can initiate on a
particular RCaP Stream. This variable is maintained only by the
iSER layer at the target.
iSER Layer - The layer that implements the iSCSI Extensions for RDMA
(iSER) protocol.
iWARP - A suite of wire protocols comprising of [RDMAP], [DDP], and
[MPA] when layered above [TCP]. [RDMAP] and [DDP] may be layered
above SCTP or other transport protocols.
Local Mapping - A task state record maintained by the iSER layer that
associates the Initiator Task Tag to the local STag(s). The
specifics of the record structure are implementation dependent.
Local Peer - The implementation of the RDMA-Capable Protocol on the
local end of the connection. Used to refer to the local entity
when describing protocol exchanges or other interactions between
two Nodes.
Node - A computing device attached to one or more links of a network.
A Node in this context does not refer to a specific application or
protocol instantiation running on the computer. A Node may
consist of one or more RDMA-Capable Controllers installed in a
host computer.
Operational Primitive - An Operational Primitive is an abstract
functional interface procedure that requests that another layer
perform a specific action on the requestor's behalf or notifies
the other layer of some event. The Datamover Interface between an
iSCSI layer and a Datamover layer within an iSCSI end node uses a
set of Operational Primitives to define the functional interface
between the two layers. Note that not every invocation of an
Operational Primitive may elicit a response from the requested
layer. A full discussion of the Operational Primitive types and
request-response semantics available to iSCSI and iSER can be
found in [DA].
Outbound RDMA Read Queue Depth (ORD) - The maximum number of
outstanding RDMA Read Requests that the RDMA-Capable Controller
can initiate on a particular RCaP Stream at the Data Sink. For
Ko, et al. Standards Track [Page 14]
RFC 5046 iSER Specification October 2007
some RDMA-Capable Protocol layer, the term "ORD" may be known by a
different name. For example, for InfiniBand, the equivalent for
ORD is the Initiator Depth.
Phase-Collapse - Refers to the optimization in iSCSI where the SCSI
status is transferred along with the final SCSI Data-in PDU from a
target. See Section 3.2 in [RFC3720].
RCaP Message - One or more packets of the network layer comprising a
single RDMA Operation or a part of an RDMA Read Operation of the
RDMA-Capable Protocol. For iWARP, an RCaP Message is known as an
RDMAP Message.
RCaP Stream - A single bidirectional association between the peer
RDMA-Capable Protocol layers on two Nodes over a single
transport-level stream. For iWARP, an RCaP Stream is known as an
RDMAP Stream, and the association is created when the connection
transitions to iSER-assisted mode following a successful Login
Phase during which iSER support is negotiated.
RDMA-Capable Protocol (RCaP) - The protocol or protocol suite that
provides a reliable RDMA transport functionality, e.g., iWARP,
InfiniBand, etc.
RDMA-Capable Controller - A network I/O adapter or embedded
controller with RDMA functionality. For example, for iWARP, this
could be an RNIC, and for InfiniBand, this could be a HCA (Host
Channel Adapter) or TCA (Target Channel Adapter).
RDMA-enabled Network Interface Controller (RNIC) - A network I/O
adapter or embedded controller with iWARP functionality.
RDMA Operation - A sequence of RCaP Messages, including control
Messages, to transfer data from a Data Source to a Data Sink. The
following RDMA Operations are defined - RDMA Write Operation, RDMA
Read Operation, Send Operation, Send with Invalidate Operation,
Send with Solicited Event Operation, Send with Solicited Event and
Invalidate Operation, and Terminate Operation.
RDMA Protocol (RDMAP) - A wire protocol that supports RDMA Operations
to transfer ULP data between a Local Peer and the Remote Peer as
described in [RDMAP].
RDMA Read Operation - An RDMA Operation used by the Data Sink to
transfer the contents of a Data Source buffer from the Remote Peer
to a Data Sink buffer at the Local Peer. An RDMA Read operation
consists of a single RDMA Read Request Message and a single RDMA
Read Response Message.
Ko, et al. Standards Track [Page 15]
RFC 5046 iSER Specification October 2007
RDMA Read Request - An RCaP Message used by the Data Sink to request
that the Data Source transfer the contents of a buffer. The RDMA
Read Request Message describes both the Data Source and the Data
Sink buffers.
RDMA Read Response - An RCaP Message used by the Data Source to
transfer the contents of a buffer to the Data Sink, in response to
an RDMA Read Request. The RDMA Read Response Message only
describes the Data Sink buffer.
RDMA Write Operation - An RDMA Operation used by the Data Source to
transfer the contents of a Data Source buffer from the Local Peer
to a Data Sink buffer at the Remote Peer. The RDMA Write Message
only describes the Data Sink buffer.
Remote Direct Memory Access (RDMA) - A method of accessing memory on
a remote system in which the local system specifies the remote
location of the data to be transferred. Employing an RDMA-
Capable Controller in the remote system allows the access to take
place without interrupting the processing of the CPU(s) on the
system.
Remote Mapping - A task state record maintained by the iSER layer
that associates the Initiator Task Tag to the Advertised STag(s).
The specifics of the record structure are implementation
dependent.
Remote Peer - The implementation of the RDMA-Capable Protocol on the
opposite end of the connection. Used to refer to the remote
entity when describing protocol exchanges or other interactions
between two Nodes.
SCSI Layer - This layer builds/receives SCSI CDBs (Command Descriptor
Blocks) and sends/receives them with the remaining command execute
[SAM2] parameters to/from the iSCSI layer.
Send - An RDMA Operation that transfers the contents of a Buffer from
the Local Peer to a Buffer at the Remote Peer.
Send Message Type - A Send Message, Send with Invalidate Message,
Send with Solicited Event Message, or Send with Solicited Event
and Invalidate Message.
SendInvSE Message - A Send with Solicited Event and Invalidate
Message.
SendSE Message - A Send with Solicited Event Message.
Ko, et al. Standards Track [Page 16]
RFC 5046 iSER Specification October 2007
Sequence Number (SN) - DataSN for a SCSI Data-in PDU and R2TSN for an
R2T PDU. The semantics for both types of sequence numbers are as
defined in [RFC3720].
Session, iSCSI Session - The group of connections that link an
initiator SCSI port with a target SCSI port form an iSCSI session
(equivalent to a SCSI I-T nexus). Connections can be added to and
removed from a session even while the I-T nexus is intact. Across
all connections within a session, an initiator sees one and the
same target.
Solicited Event (SE) - A facility by which an RDMA Operation sender
may cause an Event to be generated at the recipient, if the
recipient is configured to generate such an Event, when a Send
with Solicited Event or Send with Solicited Event and Invalidate
Message is received.
Steering Tag (STag) - An identifier of a Tagged Buffer on a Node
(Local or Remote) as defined in [RDMAP] and [DDP]. For other
RDMA-Capable Protocols, the Steering Tag may be known by different
names but will be herein referred to as STags. For example, for
InfiniBand, a Remote STag is known as an R-Key, and a local STag
is known as an L-Key, and both will be considered STags.
Tagged Buffer - A buffer that is explicitly Advertised to the iSER
layer at the remote node through the exchange of an STag, Tagged
Offset, and length.
Tagged Offset (TO) - The offset within a Tagged Buffer.
Traditional iSCSI - Refers to the iSCSI protocol as defined in
[RFC3720] (i.e. without the iSER enhancements).
Untagged Buffer - A buffer that is not explicitly Advertised to the
iSER layer at the remode node.
2.2. Acronyms
Acronym Definition
--------------------------------------------------------------
AHS Additional Header Segment
BHS Basic Header Segment
CO Connection Only
CRC Cyclic Redundancy Check
Ko, et al. Standards Track [Page 17]
RFC 5046 iSER Specification October 2007
DDP Direct Data Placement Protocol
DI Datamover Interface
HCA Host Channel Adapter
IANA Internet Assigned Numbers Authority
IB InfiniBand
IETF Internet Engineering Task Force
I/O Input - Output
IO Initialize Only
IP Internet Protocol
IPoIB IP over InfiniBand
IPsec Internet Protocol Security
iSER iSCSI Extensions for RDMA
ITT Initiator Task Tag
LO Leading Only
MPA Marker PDU Aligned Framing for TCP
NOP No Operation
NSG Next Stage (during the iSCSI Login Phase)
OS Operating System
PDU Protocol Data Unit
R2T Ready To Transfer
R2TSN Ready To Transfer Sequence Number
RDMA Remote Direct Memory Access
RDMAP Remote Direct Memory Access Protocol
RFC Request For Comments
Ko, et al. Standards Track [Page 18]
RFC 5046 iSER Specification October 2007
RNIC RDMA-enabled Network Interface Controller
SAM2 SCSI Architecture Model - 2
SCSI Small Computer Systems Interface
SNACK Selective Negative Acknowledgment - also
Sequence Number Acknowledgement for data
STag Steering Tag
SW Session Wide
TCA Target Channel Adapter
TCP Transmission Control Protocol
TMF Task Management Function
TTT Target Transfer Tag
TO Tagged Offset
ULP Upper Level Protocol
2.3. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
3. Upper Layer Interface Requirements
This section discusses the upper layer interface requirements in the
form of an abstract model of the required interactions between the
iSCSI layer and the iSER layer. The abstract model used here is
derived from the architectural model described in [DA]. [DA] also
provides a functional overview of the interactions between the iSCSI
layer and the Datamover layer as intended by the Datamover
Architecture.
The interface requirements are specified by Operational Primitives.
An Operational Primitive is an abstract functional interface
procedure between the iSCSI layer and the iSER layer that requests
one layer to perform a specific action on behalf of the other layer
or notifies the other layer of some event. Whenever an Operational
Primitive in invoked, the Connection_Handle qualifier is used to
identify a particular iSCSI connection. For some Operational
Ko, et al. Standards Track [Page 19]
RFC 5046 iSER Specification October 2007
Primitives, a Data_Descriptor is used to identify the iSCSI/SCSI data
buffer associated with the requested or completed operation.
The abstract model and the Operational Primitives defined in this
section facilitate the description of the iSER protocol. In the rest
of the iSER specification, the compliance statements related to the
use of these Operational Primitives are only for the purpose of the
required interactions between the iSCSI layer and the iSER layer.
Note that the compliance statements related to the Operational
Primitives in the rest of this specification only mandate functional
equivalence on implementations, but do not put any requirements on
the implementation specifics of the interface between the iSCSI layer
and the iSER layer.
Each Operational Primitive is invoked with a set of qualifiers that
specify the information context for performing the specific action
being requested of the Operational Primitive. While the qualifiers
are required, the method of realizing the qualifiers (e.g., by
passing synchronously with invocation, or by retrieving from task
context, or by retrieving from shared memory, etc.) is implementation
dependent.
3.1. Operational Primitives Offered by iSER
The iSER protocol layer MUST support the following Operational
Primitives to be used by the iSCSI protocol layer.
3.1.1. Send_Control
Input qualifiers: Connection_Handle, BHS and AHS (if any) of the
iSCSI PDU, PDU-specific qualifiers
Return results: Not specified
This is used by the iSCSI layers at the initiator and the target to
request the outbound transfer of an iSCSI control-type PDU (see
Section 7.2). Qualifiers that only apply for a particular control-
type PDU are known as PDU-specific qualifiers, e.g.,
ImmediateDataSize for a SCSI write command. For details on PDU-
specific qualifiers, see Section 7.3. The iSCSI layer can only
invoke the Send_Control Operational Primitive when the connection is
in iSER-assisted mode.
3.1.2. Put_Data
Input qualifiers: Connection_Handle, content of a SCSI Data-in
PDU header, Data_Descriptor, Notify_Enable
Ko, et al. Standards Track [Page 20]
RFC 5046 iSER Specification October 2007
Return results: Not specified
This is used by the iSCSI layer at the target to request the outbound
transfer of data for a SCSI Data-in PDU from the buffer identified by
the Data_Descriptor qualifier. The iSCSI layer can only invoke the
Put_Data Operational Primitive when the connection is in iSER-
assisted mode.
The Notify_Enable qualifier is used to indicate to the iSER layer
whether or not it should generate an eventual local completion
notification to the iSCSI layer. See Section 3.2.2 on
Data_Completion_Notify for details.
3.1.3. Get_Data
Input qualifiers: Connection_Handle, content of an R2T PDU,
Data_Descriptor, Notify_Enable
Return results: Not specified
This is used by the iSCSI layer at the target to request the inbound
transfer of solicited data requested by an R2T PDU into the buffer
identified by the Data_Descriptor qualifier. The iSCSI layer can
only invoke the Get_Data Operational Primitive when the connection is
in iSER-assisted mode.
The Notify_Enable qualifier is used to indicate to the iSER layer
whether or not it should generate the eventual local completion
notification to the iSCSI layer. See Section 3.2.2 on
Data_Completion_Notify for details.
3.1.4. Allocate_Connection_Resources
Input qualifiers: Connection_Handle, Resource_Descriptor
(optional)
Return results: Status
This is used by the iSCSI layers at the initiator and the target to
request the allocation of all connection resources necessary to
support RCaP for an operational iSCSI/iSER connection. The iSCSI
layer may optionally specify the implementation-specific resource
requirements for the iSCSI connection using the Resource_Descriptor
qualifier.
A return result of Status=success means that the invocation
succeeded, and a return result of Status=failure means that the
invocation failed. If the invocation is for a Connection_Handle for
Ko, et al. Standards Track [Page 21]
RFC 5046 iSER Specification October 2007
which an earlier invocation succeeded, the request will be ignored by
the iSER layer and the result of Status=success will be returned.
Only one Allocate_Connection_Resources Operational Primitive
invocation can be outstanding for a given Connection_Handle at any
time.
3.1.5. Deallocate_Connection_Resources
Input qualifiers: Connection_Handle
Return results: Not specified
This is used by the iSCSI layers at the initiator and the target to
request the deallocation of all connection resources that were
allocated earlier as a result of a successful invocation of the
Allocate_Connection_Resources Operational Primitive.
3.1.6. Enable_Datamover
Input qualifiers: Connection_Handle,
Transport_Connection_Descriptor, Final Login_Response_PDU
(optional)
Return results: Not specified
This is used by the iSCSI layers at the initiator and the target to
request that a specified iSCSI connection be transitioned to iSER-
assisted mode. The Transport_Connection_Descriptor qualifier is used
to identify the specific connection associated with the
Connection_Handle. The iSCSI layer can only invoke the
Enable_Datamover Operational Primitive when there is a corresponding
prior resource allocation.
The Final_Login_Response_PDU input qualifier is applicable only for a
target, and contains the final Login Response PDU that concludes the
iSCSI Login Phase. If the underlying transport is TCP, the final
Login Response PDU must be sent as a byte stream as expected by the
iSCSI layer at the initiator. When this qualifier is used, the iSER
layer at the target MUST transmit this final Login Response PDU
before transitioning to iSER-assisted mode.
3.1.7. Connection_Terminate
Input qualifiers: Connection_Handle
Return results: Not specified
Ko, et al. Standards Track [Page 22]
RFC 5046 iSER Specification October 2007
This is used by the iSCSI layers at the initiator and the target to
request that a specified iSCSI/iSER connection be terminated and all
associated connection and task resources be freed. When this
Operational Primitive invocation returns to the iSCSI layer, the
iSCSI layer may assume full ownership of all iSCSI-level resources,
e.g., I/O Buffers, associated with the connection.
3.1.8. Notice_Key_Values
Input qualifiers: Connection_Handle, number of keys, list of
Key-Value pairs
Return results: Not specified
This is used by the iSCSI layers at the initiator and the target to
request that the iSER layer take note of the specified Key-Value
pairs that were negotiated by the iSCSI peers for the connection.
3.1.9. Deallocate_Task_Resources
Input qualifiers: Connection_Handle, ITT
Return results: Not specified
This is used by the iSCSI layers at the initiator and the target to
request the deallocation of all RCaP-specific resources allocated by
the iSER layer for the task identified by the ITT qualifier. The
iSER layer may require a certain number of RCaP-specific resources
associated with the ITT for each new iSCSI task. In the normal
course of execution, these task-level resources in the iSER layer are
assumed to be transparently allocated on each task initiation and
deallocated on the conclusion of each task as appropriate. In
exception scenarios where the task does not conclude with a SCSI
Response PDU, the iSER layer needs to be notified of the individual
task terminations to aid its task-level resource management. This
Operational Primitive is used for this purpose, and is not needed
when a SCSI Response PDU normally concludes a task. Note that RCaP-
specific task resources are deallocated by the iSER layer when a SCSI
Response PDU normally concludes a task, even if the SCSI status was
not success.
3.2. Operational Primitives Used by iSER
The iSER layer MUST use the following Operational Primitives offered
by the iSCSI protocol layer when the connection is in iSER-assisted
mode.
Ko, et al. Standards Track [Page 23]
RFC 5046 iSER Specification October 2007
3.2.1. Control_Notify
Input qualifiers: Connection_Handle, an iSCSI control-type PDU
Return results: Not specified
This is used by the iSER layers at the initiator and the target to
notify the iSCSI layer of the availability of an inbound iSCSI
control-type PDU. A PDU is described as "available" to the iSCSI
layer when the iSER layer notifies the iSCSI layer of the reception
of that inbound PDU, along with an implementation-specific indication
as to where the received PDU is.
3.2.2. Data_Completion_Notify
Input qualifiers: Connection_Handle, ITT, SN
Return results: Not specified
This is used by the iSER layer to notify the iSCSI layer of the
completion of outbound data transfer that was requested by the iSCSI
layer only if the invocation of the Put_Data Operational Primitive
(see Section 3.1.2) was qualified with Notify_Enable set. SN refers
to the DataSN associated with the SCSI Data-in PDU.
This is used by the iSER layer to notify the iSCSI layer of the
completion of inbound data transfer that was requested by the iSCSI
layer only if the invocation of the Get_Data Operational Primitive
(see Section 3.1.3) was qualified with Notify_Enable set. SN refers
to the R2TSN associated with the R2T PDU.
3.2.3. Data_ACK_Notify
Input qualifier: Connection_Handle, ITT, DataSN
Return results: Not specified
This is used by the iSER layer at the target to notify the iSCSI
layer of the arrival of the data acknowledgement (as defined in
[RFC3720]) requested earlier by the iSCSI layer for the outbound data
transfer via an invocation of the Put_Data Operational Primitive
where the A-bit in the SCSI Data-in PDU is set to 1. See Section
7.3.5. DataSN refers to the expected DataSN of the next SCSI Data-in
PDU, which immediately follows the SCSI Data-in PDU with the A-bit
set to which this notification corresponds, with semantics as defined
in [RFC3720].
Ko, et al. Standards Track [Page 24]
RFC 5046 iSER Specification October 2007
3.2.4. Connection_Terminate_Notify
Input qualifiers: Connection_Handle
Return results: Not specified
This is used by the iSER layers at the initiator and the target to
notify the iSCSI layer of the unsolicited termination or failure of
an iSCSI/iSER connection. The iSER layer MUST deallocate the
connection and task resources associated with the terminated
connection before the invocation of this Operational Primitive. Note
that the Connection_Terminate_Notify Operational Primitive is not
invoked when the termination of the connection is earlier requested
by the local iSCSI layer.
3.3. iSCSI Protocol Usage Requirements
To operate in an iSER-assisted mode, the iSCSI layers at both the
initiator and the target MUST negotiate the RDMAExtensions key (see
Section 6.3) to "Yes" on the leading connection. If the
RDMAExtensions key is not negotiated to "Yes", then iSER-assisted
mode MUST NOT be used. If the RDMAExtensions key is negotiated to
"Yes" but the invocation of the Allocate_Connection_Resources
Operational Primitive to the iSER layer fails, the iSCSI layer MUST
fail the iSCSI Login process or terminate the connection as
appropriate. See Section 10.1.3.1 for details.
If the RDMAExtensions key is negotiated to "Yes", the iSCSI layer
MUST satisfy the following protocol usage requirements from the iSER
protocol:
1. The iSCSI layer at the initiator MUST set ExpDataSN to 0 in Task
Management Function Requests for Task Allegiance Reassignment for
read/bidirectional commands, so as to cause the target to send
all unacknowledged read data.
2. The iSCSI layer at the target MUST always return the SCSI status
in a separate SCSI Response PDU for read commands, i.e., there
MUST NOT be a "phase collapse" in concluding a SCSI read command.
3. The iSCSI layers at both the initiator and the target MUST
support the keys as defined in Section 6 on Login/Text
Operational Keys. If used as specified, these keys MUST NOT be
answered with NotUnderstood, and the semantics as defined MUST be
followed for each iSER-assisted connection.
4. The iSCSI layer at the initiator MUST NOT issue SNACKs for PDUs.
Ko, et al. Standards Track [Page 25]
RFC 5046 iSER Specification October 2007
4. Lower Layer Interface Requirements
4.1. Interactions with the RCaP Layer
The iSER protocol layer is layered on top of an RCaP layer (see
Figure 1) and the following are the key features that are assumed to
be supported by any RCaP layer:
* The RCaP layer supports all basic RDMA operations, including RDMA
Write Operation, RDMA Read Operation, Send Operation, Send with
Invalidate Operation, Send with Solicited Event Operation, Send
with Solicited Event and Invalidate Operation, and Terminate
Operation.
* The RCaP layer provides reliable, in-order message delivery and
direct data placement.
* When the iSER layer initiates an RDMA Read Operation following an
RDMA Write Operation on one RCaP Stream, the RDMA Read Response
Message processing on the remote node will be started only after
the preceding RDMA Write Message payload is placed in the memory
of the remote node.
* The RCaP layer encapsulates a single iSER Message into a single
RCaP Message on the Data Source side. The RCaP layer decapsulates
the iSER Message before delivering it to the iSER layer on the
Data Sink side.
* When the iSER layer provides the STag to be remotely invalidated
to the RCaP layer for a SendInvSE Message, the RCaP layer uses
this STag as the STag to be invalidated in the SendInvSE Message.
* The RCaP layer uses the STag and Tagged Offset provided by the
iSER layer for the RDMA Write and RDMA Read Request Messages.
* When the RCaP layer delivers the content of an RDMA Send Message
Type to the iSER layer, the RCaP layer provides the length of the
RDMA Send message. This ensures that the iSER layer does not have
to carry a length field in the iSER header.
* When the RCaP layer delivers the SendSE or SendInvSE Message to
the iSER layer, it notifies the iSER layer with the mechanism
provided on that interface.
* When the RCaP layer delivers a SendInvSE Message to the iSER
layer, it passes the value of the STag that was invalidated.
Ko, et al. Standards Track [Page 26]
RFC 5046 iSER Specification October 2007
* The RCaP layer propagates all status and error indications to the
iSER layer.
* For a transport layer that operates in byte stream mode such as
TCP, the RCaP implementation supports the enabling of the RDMA
mode after connection establishment and the exchange of Login
parameters in byte stream mode. For a transport layer that
provides message delivery capability such as [IB], the RCaP
implementation supports the use of the messaging capability by the
iSCSI layer directly for the Login Phase after connection
establishment before enabling iSER-assisted mode.
* Whenever the iSER layer terminates the RCaP Stream, the RCaP layer
terminates the associated connection.
4.2. Interactions with the Transport Layer
The iSER layer does not directly setup the transport layer connection
(e.g., TCP, or [IB]). During connection setup, the iSCSI layer is
responsible for setting up the connection. If the login is
successful, the iSCSI layer invokes the Enable_Datamover Operational
Primitive to request the iSER layer to transition to the iSER-
assisted mode for that iSCSI connection. See Section 5.1 on
iSCSI/iSER connection setup. After transitioning to iSER-assisted
mode, the RCaP layer and the underlying transport layer are
responsible for maintaining the connection and reporting to the iSER
layer any connection failures.
5. Connection Setup and Termination
5.1. iSCSI/iSER Connection Setup
During connection setup, the iSCSI layer at the initiator is
responsible for establishing a connection with the target. After the
connection is established, the iSCSI layers at the initiator and the
target enter the Login Phase using the same rules as outlined in
[RFC3720]. Transition to iSER-assisted mode occurs when the
connection transitions into the iSCSI Full Feature Phase following a
successful login negotiation between the initiator and the target in
which iSER-assisted mode is negotiated and the connection resources
necessary to support RCaP have been allocated at both the initiator
and the target. The same connection MUST be used for both the iSCSI
Login Phase and the subsequent iSER-assisted Full Feature Phase.
iSER-assisted mode MUST be enabled only if it is negotiated on the
leading connection during the LoginOperationalNegotiation stage of
the iSCSI Login Phase. iSER-assisted mode is negotiated using the
RDMAExtensions=<boolean-value> key. Both the initiator and the
Ko, et al. Standards Track [Page 27]
RFC 5046 iSER Specification October 2007
target MUST exchange the RDMAExtensions key with the value set to
"Yes" to enable iSER-assisted mode. If both the initiator and the
target fail to negotiate the RDMAExtensions key set to "Yes", then
the connection MUST continue with the login semantics as defined in
[RFC3720]. If the RDMAExtensions key is not negotiated to Yes, then
for some RCaP implementation (such as [IB]), the connection may need
to be re-established in TCP capable mode. (For InfiniBand this will
require an [IPoIB] type connection.)
iSER-assisted mode is defined for a Normal session only and the
RDMAExtensions key MUST NOT be negotiated for a Discovery session.
Discovery sessions are always conducted using the transport layer as
described in [RFC3720].
An iSER enabled node is not required to initiate the RDMAExtensions
key exchange if its preference is for the Traditional iSCSI mode.
The RDMAExtensions key, if offered, MUST be sent in the first
available Login Response or Login Request PDU in the
LoginOperationalNegotiation stage. This is due to the fact that the
value of some login parameters might depend on whether iSER-assisted
mode is enabled.
iSER-assisted mode is a session-wide attribute. If both the
initiator and the target negotiate RDMAExtensions="Yes" on the
leading connection of a session, then all subsequent connections of
the same session MUST enable iSER-assisted mode without having to
exchange an RDMAExtensions key during the iSCSI Login Phase.
Conversely, if both the initiator and the target fail to negotiate
RDMAExtensions to "Yes" on the leading connection of a session, then
the RDMAExtensions key MUST NOT be negotiated further on any
additional subsequent connection of the session.
When the RDMAExtensions key is negotiated to "Yes", the HeaderDigest
and the DataDigest keys MUST be negotiated to "None" on all
iSCSI/iSER connections participating in that iSCSI session. This is
because, for an iSCSI/iSER connection, RCaP is responsible for
providing error detection that is at least as good as a 32-bit CRC
for all iSER Messages. Furthermore, all SCSI Read data are sent
using RDMA Write Messages instead of the SCSI Data-in PDUs, and all
solicited SCSI write data are sent using RDMA Read Response Messages
instead of the SCSI Data-out PDUs. HeaderDigest and DataDigest that
apply to iSCSI PDUs, would not be appropriate for RDMA Read and RDMA
Write operations used with iSER.
Ko, et al. Standards Track [Page 28]
RFC 5046 iSER Specification October 2007
5.1.1. Initiator Behavior
If the outcome of the iSCSI negotiation is to enable iSER-assisted
mode, then on the initiator side, prior to sending the Login Request
with the T (Transit) bit set to 1 and the NSG (Next Stage) field set
to FullFeaturePhase, the iSCSI layer MUST request that the iSER layer
allocate the connection resources necessary to support RCaP by
invoking the Allocate_Connection_Resources Operational Primitive.
The connection resources required are defined by implementation and
are outside the scope of this specification. The iSCSI layer may
invoke the Notice_Key_Values Operational Primitive before invoking
the Allocate_Connection_Resources Operational Primitive to request
that the iSER layer take note of the negotiated values of the iSCSI
keys for the connection. The specific keys to be passed as input
qualifiers are implementation dependent. These may include, but are
not limited to, MaxOutstandingR2T, ErrorRecoveryLevel, etc.
To minimize the potential for a denial-of service attack, the iSCSI
layer MUST NOT request that the iSER layer allocate the connection
resources necessary to support RCaP until the iSCSI layer is
sufficiently far along in the iSCSI Login Phase that it is reasonably
certain that the peer side is not an attacker. In particular, if the
Login Phase includes a SecurityNegotiation stage, the iSCSI layer
MUST defer the connection resource allocation (i.e., invoking the
Allocate_Connection_Resources Operational Primitive) to the
LoginOperationalNegotiation stage [RFC3720] so that the resource
allocation occurs after the authentication phase is completed.
Among the connection resources allocated at the initiator is the
Inbound RDMA Read Queue Depth (IRD). As described in Section 9.5.1,
R2Ts are transformed by the target into RDMA Read operations. IRD
limits the maximum number of simultaneously incoming outstanding RDMA
Read Requests per an RCaP Stream from the target to the initiator.
The required value of IRD is outside the scope of the iSER
specification. The iSER layer at the initiator MUST set IRD to 1 or
higher if R2Ts are to be used in the connection. However, the iSER
layer at the initiator MAY set IRD to 0 based on implementation
configuration, which indicates that no R2Ts will be used on that
connection. Initially, the iSER-IRD value at the initiator SHOULD be
set to the IRD value at the initiator and MUST NOT be more than the
IRD value.
On the other hand, the Outbound RDMA Read Queue Depth (ORD) MAY be
set to 0, since the iSER layer at the initiator does not issue RDMA
Read Requests to the target.
Ko, et al. Standards Track [Page 29]
RFC 5046 iSER Specification October 2007
Failure to allocate the requested connection resources locally
results in a login failure and its handling is described in Section
10.1.3.1.
If the iSER layer at the initiator is successful in allocating the
connection resources necessary to support RCaP, the following events
MUST occur in the specified sequence:
1. The iSER layer MUST return a success status to the iSCSI layer in
response to the Allocate_Connection_Resources Operational
Primitive.
2. After the target returns the Login Response with the T bit set to
1 and the NSG field set to FullFeaturePhase, and a status class
of 0 (Success), the iSCSI layer MUST request that the iSER layer
transition to iSER-assisted mode by invoking the Enable_Datamover
Operational Primitive with the following qualifiers. (See
Section 10.1.4.6 for the case when the status class is not
Success.):
a. Connection_Handle that identifies the iSCSI connection.
b. Transport_Connection_Descriptor that identifies the specific
transport connection associated with the Connection_Handle.
3. If necessary, the iSER layer should enable RCaP and transition
the connection to iSER-assisted mode. When the RCaP is iWARP,
then this step MUST be done. Not all RCaPs may need it depending
on the RCaP Stream start-up state.
4. The iSER layer MUST send the iSER Hello Message as the first iSER
Message. See Section 5.1.3 on iSER Hello Exchange.
5.1.2. Target Behavior
If the outcome of the iSCSI negotiation is to enable iSER-assisted
mode, then on the target side, prior to sending the Login Response
with the T (Transit) bit set to 1 and the NSG (Next Stage) field set
to FullFeaturePhase, the iSCSI layer MUST request that the iSER layer
allocate the resources necessary to support RCaP by invoking the
Allocate_Connection_Resources Operational Primitive. The connection
resources required are defined by implementation and are outside the
scope of this specification. Optionally, the iSCSI layer may invoke
the Notice_Key_Values Operational Primitive before invoking the
Allocate_Connection_Resources Operational Primitive to request that
the iSER layer take note of the negotiated values of the iSCSI keys
for the connection. The specific keys to be passed as input
Ko, et al. Standards Track [Page 30]
RFC 5046 iSER Specification October 2007
qualifiers are implementation dependent. These may include, but are
not limited to, MaxOutstandingR2T, ErrorRecoveryLevel, etc.
To minimize the potential for a denial-of-service attack, the iSCSI
layer MUST NOT request that the iSER layer allocate the connection
resources necessary to support RCaP until the iSCSI layer is
sufficiently far along in the iSCSI Login Phase that it is reasonably
certain that the peer side is not an attacker. In particular, if the
Login Phase includes a SecurityNegotiation stage, the iSCSI layer
MUST defer the connection resource allocation (i.e., invoking the
Allocate_Connection_Resources Operational Primitive) to the
LoginOperationalNegotiation stage [RFC3720] so that the resource
allocation occurs after the authentication phase is completed.
Among the connection resources allocated at the target is the
Outbound RDMA Read Queue Depth (ORD). As described in Section 9.5.1,
R2Ts are transformed by the target into RDMA Read operations. The
ORD limits the maximum number of simultaneously outstanding RDMA Read
Requests per RCaP Stream from the target to the initiator.
Initially, the iSER-ORD value at the target SHOULD be set to the ORD
value at the target.
On the other hand, the IRD at the target MAY be set to 0 since the
iSER layer at the target does not expect RDMA Read Requests to be
issued by the initiator.
Failure to allocate the requested connection resources locally
results in a login failure and its handling is described in Section
10.1.3.1.
If the iSER layer at the target is successful in allocating the
connection resources necessary to support RCaP, the following events
MUST occur in the specified sequence:
1. The iSER layer MUST return a success status to the iSCSI layer in
response to the Allocate_Connection_Resources Operational
Primitive.
2. The iSCSI layer MUST request that the iSER layer transition to
iSER-assisted mode by invoking the Enable_Datamover Operational
Primitive with the following qualifiers:
a. Connection_Handle that identifies the iSCSI connection.
b. Transport_Connection_Descriptor that identifies the specific
transport connection associated with the Connection_Handle.
Ko, et al. Standards Track [Page 31]
RFC 5046 iSER Specification October 2007
c. The final transport layer (e.g., TCP) message containing the
Login Response with the T bit set to 1 and the NSG field set
to FullFeaturePhase.
3. The iSER layer MUST send the final Login Response PDU in the
native transport mode to conclude the iSCSI Login Phase. If the
underlying transport is TCP, then the iSER layer MUST send the
final Login Response PDU in byte stream mode.
4. After sending the final Login Response PDU, the iSER layer should
enable RCaP if necessary and transition the connection to iSER-
assisted mode. When the RCaP is iWARP, then this step MUST be
done. Not all RCaPs may need it depending on the RCaP Stream
start-up state.
5. After receiving the iSER Hello Message from the initiator, the
iSER layer MUST respond with the iSER HelloReply Message to be
sent as the first iSER Message. See Section 5.1.3 on iSER Hello
Exchange for more details.
Note: In the above sequence, the operations as described in bullets 3
and 4 MUST be performed atomically for iWARP connections. Failure to
do this may result in race conditions.
5.1.3. iSER Hello Exchange
After the connection transitions into iSER-assisted mode, the first
iSER Message sent by the iSER layer at the initiator to the target
MUST be the iSER Hello Message. The iSER Hello Message is used by
the iSER layer at the initiator to declare iSER parameters to the
target. See Section 9.3 on iSER Header Format for the iSER Hello
Message.
In response to the iSER Hello Message, the iSER layer at the target
MUST return the iSER HelloReply Message as the first iSER Message
sent by the target. The iSER HelloReply Message is used by the iSER
layer at the target to declare iSER parameters to the initiator. See
Section 9.4 on iSER Header Format for the iSER HelloReply Message.
In the iSER Hello Message, the iSER layer at the initiator declares
the iSER-IRD value to the target.
Upon receiving the iSER Hello Message, the iSER layer at the target
MUST set the iSER-ORD value to the minimum of the iSER-ORD value at
the target and the iSER-IRD value declared by the initiator. The
iSER layer at the target MAY adjust (lower) its ORD value to match
the iSER-ORD value if the iSER-ORD value is smaller than the ORD
value at the target in order to free up the unused resources.
Ko, et al. Standards Track [Page 32]
RFC 5046 iSER Specification October 2007
In the iSER HelloReply Message, the iSER layer at the target declares
the iSER-ORD value to the initiator.
Upon receiving the iSER HelloReply Message, the iSER layer at the
initiator MAY adjust (lower) its IRD value to match the iSER-ORD
value in order to free up the unused resources, if the iSER-ORD value
declared by the target is smaller than the iSER-IRD value declared by
the initiator.
It is an iSER level negotiation failure if the iSER parameters
declared in the iSER Hello Message by the initiator are unacceptable
to the target. This includes the following:
* The initiator-declared iSER-IRD value is greater than 0 and the
target-declared iSER-ORD value is 0.
* The initiator-supported and the target-supported iSER protocol
versions do not overlap.
See Section 10.1.3.2 for the handling of the error situation.
5.2. iSCSI/iSER Connection Termination
5.2.1. Normal Connection Termination at the Initiator
The iSCSI layer at the initiator terminates an iSCSI/iSER connection
normally by invoking the Send_Control Operational Primitive qualified
with the Logout Request PDU. The iSER layer at the initiator MUST
use a SendSE Message to send the Logout Request PDU to the target.
After the iSER layer at the initiator receives the SendSE Message
containing the Logout Response PDU from the target, it MUST notify
the iSCSI layer by invoking the Control_Notify Operational Primitive
qualified with the Logout Response PDU.
After the iSCSI logout process is complete, the iSCSI layer at the
target is responsible for closing the iSCSI/iSER connection as
described in Section 5.2.2. After the RCaP layer at the initiator
reports that the connection has been closed, the iSER layer at the
initiator MUST deallocate all connection and task resources (if any)
associated with the connection, and invalidate the Local Mapping(s)
(if any) that associate the ITT(s) used on that connection to the
local STag(s) before notifying the iSCSI layer by invoking the
Connection_Terminate_Notify Operational Primitive.
Ko, et al. Standards Track [Page 33]
RFC 5046 iSER Specification October 2007
5.2.2. Normal Connection Termination at the Target
Upon receiving the SendSE Message containing the Logout Request PDU,
the iSER layer at the target MUST notify the iSCSI layer at the
target by invoking the Control_Notify Operational Primitive qualified
with the Logout Request PDU. The iSCSI layer completes the logout
process by invoking the Send_Control Operational Primitive qualified
with the Logout Response PDU. The iSER layer at the target MUST use
a SendSE Message to send the Logout Response PDU to the initiator.
After the iSCSI logout process is complete, the iSCSI layer at the
target MUST request that the iSER layer at the target terminate the
RCaP Stream by invoking the Connection_Terminate Operational
Primitive.
As part of the termination process, the RCaP layer MUST close the
connection. When the RCaP layer notifies the iSER layer after the
RCaP Stream and the associated connection are terminated, the iSER
layer MUST deallocate all connection and task resources (if any)
associated with the connection, and invalidate the Local and Remote
Mapping(s) (if any) that associate the ITT(s) used on that connection
to the local STag(s) and the Advertised STag(s) respectively.
5.2.3. Termination without Logout Request/Response PDUs
5.2.3.1. Connection Termination Initiated by the iSCSI Layer
The Connection_Terminate Operational Primitive MAY be invoked by the
iSCSI layer to request that the iSER layer terminate the RCaP Stream
without having previously exchanged the Logout Request and Logout
Response PDUs between the two iSCSI/iSER nodes. As part of the
termination process, the RCaP layer will close the connection. When
the RCaP layer notifies the iSER layer after the RCaP Stream and the
associated connection are terminated, the iSER layer MUST perform the
following actions.
If the Connection_Terminate Operational Primitive is invoked by the
iSCSI layer at the target, then the iSER layer at the target MUST
deallocate all connection and task resources (if any) associated with
the connection, and invalidate the Local and Remote Mappings (if any)
that associate the ITT(s) used on the connection to the local STag(s)
and the Advertised STag(s), respectively.
If the Connection_Terminate Operational Primitive is invoked by the
iSCSI layer at the initiator, then the iSER layer at the initiator
MUST deallocate all connection and task resources (if any) associated
with the connection, and invalidate the Local Mapping(s) (if any)
that associate the ITT(s) used on the connection to the local
STag(s).
Ko, et al. Standards Track [Page 34]
RFC 5046 iSER Specification October 2007
5.2.3.2. Connection Termination Notification to the iSCSI Layer
If the iSCSI/iSER connection is terminated without the invocation of
Connection_Terminate from the iSCSI layer, the iSER layer MUST notify
the iSCSI layer that the iSCSI/iSER connection has been terminated by
invoking the Connection_Terminate_Notify Operational Primitive.
Prior to invoking Connection_Terminate_Notify, the iSER layer at the
target MUST deallocate all connection and task resources (if any)
associated with the connection, and invalidate the Local and Remote
Mappings (if any) that associate the ITT(s) used on the connection to
the local STag(s) and the Advertised STag(s), respectively.
Prior to invoking Connection_Terminate_Notify, the iSER layer at the
initiator MUST deallocate all connection and task resources (if any)
associated with the connection, and invalidate the Local Mappings (if
any) that associate the ITT(s) used on the connection to the local
STag(s).
If the remote iSCSI/iSER node initiated the closing of the connection
(e.g., by sending a TCP FIN or TCP RST), the iSER layer MUST notify
the iSCSI layer after the RCaP layer reports that the connection is
closed by invoking the Connection_Terminate_Notify Operational
Primitive.
Another example of a connection termination without a preceding
logout is when the iSCSI layer at the initiator does an implicit
logout (connection reinstatement).
6. Login/Text Operational Keys
Certain iSCSI login/text operational keys have restricted usage in
iSER, and additional keys are used to support the iSER protocol
functionality. All other keys defined in [RFC3720] and not discussed
in this section may be used on iSCSI/iSER connections with the same
semantics.
6.1. HeaderDigest and DataDigest
Irrelevant when: RDMAExtensions=Yes
Negotiations resulting in RDMAExtensions=Yes for a session implies
HeaderDigest=None and DataDigest=None for all connections in that
session and overrides both the default and an explicit setting.
Ko, et al. Standards Track [Page 35]
RFC 5046 iSER Specification October 2007
6.2. MaxRecvDataSegmentLength
For an iSCSI connection belonging to a session in which
RDMAExtensions=Yes was negotiated on the leading connection of the
session, MaxRecvDataSegmentLength need not be declared in the Login
Phase. Instead, InitiatorRecvDataSegmentLength (as described in
Section 6.5) and TargetRecvDataSegmentLength (as described in Section
6.4) keys are negotiated. The values of the local and remote
MaxRecvDataSegmentLength are derived from the
InitiatorRecvDataSegmentLength and TargetRecvDataSegmentLength keys
even if the MaxRecvDataSegmentLength is declared during the Login
Phase.
In the Full Feature Phase, the initiator MUST consider the value of
its local MaxRecvDataSegmentLength (that it would have declared to
the target) as having the value of InitiatorRecvDataSegmentLength,
and the value of the remote MaxRecvDataSegmentLength (that would have
been declared by the target) as having the value of
TargetRecvDataSegmentLength. Similarly, the target MUST consider the
value of its local MaxRecvDataSegmentLength (that it would have
declared to the initiator) as having the value of
TargetRecvDataSegmentLength, and the value of the remote
MaxRecvDataSegmentLength (that would have been declared by the
initiator) as having the value of InitiatorRecvDataSegmentLength.
The MaxRecvDataSegmentLength key is applicable only for iSCSI
control-type PDUs.
6.3. RDMAExtensions
Use: LO (leading only)
Senders: Initiator and Target
Scope: SW (session-wide)
RDMAExtensions=<boolean-value>
Irrelevant when: SessionType=Discovery
Default is No
Result function is AND
This key is used by the initiator and the target to negotiate support
for iSER-assisted mode. To enable the use of iSER-assisted mode,
both the initiator and the target MUST exchange RDMAExtensions=Yes.
Ko, et al. Standards Track [Page 36]
RFC 5046 iSER Specification October 2007
iSER-assisted mode MUST NOT be used if either the initiator or the
target offers RDMAExtensions=No.
An iSER-enabled node is not required to initiate the RDMAExtensions
key exchange if it prefers to operate in the Traditional iSCSI mode.
However, if the RDMAExtensions key is to be negotiated, an initiator
MUST offer the key in the first Login Request PDU in the
LoginOperationalNegotiation stage of the leading connection, and a
target MUST offer the key in the first Login Response PDU with which
it is allowed to do so (i.e., the first Login Response PDU issued
after the first Login Request PDU with the C bit set to 0) in the
LoginOperationalNegotiation stage of the leading connection. In
response to the offered key=value pair of RDMAExtensions=yes, an
initiator MUST respond in the next Login Request PDU with which it is
allowed to do so, and a target MUST respond in the next Login
Response PDU with which it is allowed to do so.
Negotiating the RDMAExtensions key first enables a node to negotiate
the optimal value for other keys. Certain iSCSI keys such as
MaxBurstLength, MaxOutstandingR2T, ErrorRecoveryLevel, InitialR2T,
ImmediateData, etc., may be negotiated differently depending on
whether the connection is in Traditional iSCSI mode or iSER-assisted
mode.
6.4. TargetRecvDataSegmentLength
Use: IO (Initialize only)
Senders: Initiator and Target
Scope: CO (connection-only)
Irrelevant when: RDMAExtensions=No
TargetRecvDataSegmentLength=<numerical-value-512-to-(2**24-1)>
Default is 8192 bytes
Result function is minimum
This key is relevant only for the iSCSI connection of an iSCSI
session if RDMAExtensions=Yes is negotiated on the leading connection
of the session. It is used by the initiator and target to negotiate
the maximum size of the data segment that an initiator may send to
the target in an iSCSI control-type PDU in the Full Feature Phase.
For SCSI Command PDUs and SCSI Data-out PDUs containing non-immediate
unsolicited data to be sent by the initiator, the initiator MUST send
all non-Final PDUs with a data segment size of exactly
Ko, et al. Standards Track [Page 37]
RFC 5046 iSER Specification October 2007
TargetRecvDataSegmentLength whenever the PDUs constitute a data
sequence whose size is larger than TargetRecvDataSegmentLength.
6.5. InitiatorRecvDataSegmentLength
Use: IO (Initialize only)
Senders: Initiator and Target
Scope: CO (connection-only)
Irrelevant when: RDMAExtensions=No
InitiatorRecvDataSegmentLength=<numerical-value-512-to-(2**24-1)>
Default is 8192 bytes
Result function is minimum
This key is relevant only for the iSCSI connection of an iSCSI
session if RDMAExtensions=Yes is negotiated on the leading connection
of the session. It is used by the initiator and target to negotiate
the maximum size of the data segment that a target may send to the
initiator in an iSCSI control-type PDU in the Full Feature Phase.
6.6. OFMarker and IFMarker
Irrelevant when: RDMAExtensions=Yes
Negotiations resulting in RDMAExtensions=Yes for a session implies
OFMarker=No and IFMarker=No for all connections in that session and
overrides both the default and an explicit setting.
6.7. MaxOutstandingUnexpectedPDUs
Use: LO (leading only), Declarative
Senders: Initiator and Target
Scope: SW (session-wide)
Irrelevant when: RDMAExtensions=No
MaxOutstandingUnexpectedPDUs=<numerical-value-from-2-to-(2**32-1) |
0>
Default is 0
Ko, et al. Standards Track [Page 38]
RFC 5046 iSER Specification October 2007
This key is used by the initiator and the target to declare the
maximum number of outstanding "unexpected" iSCSI control-type PDUs
that it can receive in the Full Feature Phase. It is intended to
allow the receiving side to determine the amount of buffer resources
needed beyond the normal flow control mechanism available in iSCSI.
An initiator or target should select a value such that it would not
impose an unnecessary constraint on the iSCSI layer under normal
circumstances. The value of 0 is defined to indicate that the
declarer has no limit on the maximum number of outstanding
"unexpected" iSCSI control-type PDUs that it can receive. See
Sections 8.1.1 and 8.1.2 for the usage of this key. Note that iSER
Hello and HelloReply Messages are not iSCSI control-type PDUs and are
not affected by this key.
7. iSCSI PDU Considerations
When a connection is in the iSER-assisted mode, two types of message
transfers are allowed between the iSCSI layer at the initiator and
the iSCSI layer at the target. These are known as the iSCSI data-
type PDUs and the iSCSI control-type PDUs, and these terms are
described in the following sections.
7.1. iSCSI Data-Type PDU
An iSCSI data-type PDU is defined as an iSCSI PDU that causes data
transfer, transparent to the remote iSCSI layer, to take place
between the peer iSCSI nodes in the full feature phase of an
iSCSI/iSER connection. An iSCSI data-type PDU, when requested for
transmission by the iSCSI layer in the sending node, results in the
data being transferred without the participation of the iSCSI layers
at the sending and the receiving nodes. This is due to the fact that
the PDU itself is not delivered as-is to the iSCSI layer in the
receiving node. Instead, the data transfer operations are
transformed into the appropriate RDMA operations that are handled by
the RDMA-Capable Controller. The set of iSCSI data-type PDUs
consists of SCSI Data-in PDUs and R2T PDUs.
If the invocation of the Operational Primitive by the iSCSI layer to
request that the iSER layer process an iSCSI data-type PDU is
qualified with Notify_Enable set, then upon completing the RDMA
operation, the iSER layer at the target MUST notify the iSCSI layer
at the target by invoking the Data_Completion_Notify Operational
Primitive qualified with ITT and SN. There is no data completion
notification at the initiator since the RDMA operations are
completely handled by the RDMA-Capable Controller at the initiator
and the iSER layer at the initiator is not involved with the data
transfer associated with iSCSI data-type PDUs.
Ko, et al. Standards Track [Page 39]
RFC 5046 iSER Specification October 2007
If the invocation of the Operational Primitive by the iSCSI layer to
request that the iSER layer process an iSCSI data-type PDU is
qualified with Notify_Enable cleared, then upon completing the RDMA
operation, the iSER layer at the target MUST NOT notify the iSCSI
layer at the target and MUST NOT invoke the Data_Completion_Notify
Operational Primitive.
If an operation associated with an iSCSI data-type PDU fails for any
reason, the contents of the Data Sink buffers associated with the
operation are considered indeterminate.
7.2. iSCSI Control-Type PDU
Any iSCSI PDU that is not an iSCSI data-type PDU and also not a SCSI
Data-out PDU carrying solicited data is defined as an iSCSI control-
type PDU. The iSCSI layer invokes the Send_Control Operational
Primitive to request that the iSER layer process an iSCSI control-
type PDU. iSCSI control-type PDUs are transferred using Send Message
Types of RCaP. Specifically, note that SCSI Data-out PDUs carrying
unsolicited data are defined as iSCSI control-type PDUs. See Section
7.3.4 on the treatment of SCSI Data-out PDUs.
When the iSER layer receives an iSCSI control-type PDU, it MUST
notify the iSCSI layer by invoking the Control_Notify Operational
Primitive qualified with the iSCSI control-type PDU.
7.3. iSCSI PDUs
This section describes the handling of each of the iSCSI PDU types by
the iSER layer. The iSCSI layer requests that the iSER layer process
the iSCSI PDU by invoking the appropriate Operational Primitive. A
Connection_Handle MUST qualify each of these invocations. In
addition, BHS and the optional AHS of the iSCSI PDU as defined in
[RFC3720] MUST qualify each of the invocations. The qualifying
Connection_Handle, the BHS, and the AHS are not explicitly listed in
the subsequent sections.
7.3.1. SCSI Command
Type: control-type PDU
PDU-specific qualifiers (for SCSI Write or bidirectional command):
ImmediateDataSize, UnsolicitedDataSize, DataDescriptorOut
PDU-specific qualifiers (for SCSI read or bidirectional command):
DataDescriptorIn
Ko, et al. Standards Track [Page 40]
RFC 5046 iSER Specification October 2007
The iSER layer at the initiator MUST send the SCSI command in a
SendSE Message to the target.
For a SCSI Write or bidirectional command, the iSCSI layer at the
initiator MUST invoke the Send_Control Operational Primitive as
follows:
* If there is immediate data to be transferred for the SCSI Write or
bidirectional command, the qualifier ImmediateDataSize MUST be
used to define the number of bytes of immediate unsolicited data
to be sent with the Write or bidirectional command, and the
qualifier DataDescriptorOut MUST be used to define the initiator's
I/O Buffer containing the SCSI Write data.
* If there is unsolicited data to be transferred for the SCSI Write
or bidirectional command, the qualifier UnsolicitedDataSize MUST
be used to define the number of bytes of immediate and non-
immediate unsolicited data for the command. The iSCSI layer will
issue one or more SCSI Data-out PDUs for the non-immediate
unsolicited data. See Section 7.3.4 on SCSI Data-out.
* If there is solicited data to be transferred for the SCSI write or
bidirectional command, as indicated by the Expected Data Transfer
Length in the SCSI Command PDU exceeding the value of
UnsolicitedDataSize, the iSER layer at the initiator MUST do the
following:
a. It MUST allocate a Write STag for the I/O Buffer defined by
the qualifier DataDescriptorOut. The DataDescriptorOut
describes the I/O buffer starting with the immediate
unsolicited data (if any), followed by the non-immediate
unsolicited data (if any) and solicited data. This means
that the BufferOffset for the SCSI Data-out for this
command is equal to the TO. This implies that a zero TO
for this STag points to the beginning of this I/O Buffer.
b. It MUST establish a Local Mapping that associates the
Initiator Task Tag (ITT) to the Write STag.
c. It MUST Advertise the Write STag to the target by sending
it as the Write STag in the iSER header of the iSER Message
(the payload of the SendSE Message of RCaP) containing the
SCSI write or bidirectional command PDU. See Section 9.2
on iSER Header Format for the iSCSI Control-Type PDU.
For a SCSI read or bidirectional command, the iSCSI layer at the
initiator MUST invoke the Send_Control Operational Primitive
qualified with DataDescriptorIn, which defines the initiator's I/O
Ko, et al. Standards Track [Page 41]
RFC 5046 iSER Specification October 2007
Buffer for receiving the SCSI Read data. The iSER layer at the
initiator MUST do the following:
a. It MUST allocate a Read STag for the I/O Buffer.
b. It MUST establish a Local Mapping that associates the
Initiator Task Tag (ITT) to the Read STag.
c. It MUST Advertise the Read STag to the target by sending it
as the Read STag in the iSER header of the iSER Message
(the payload of the SendSE Message of RCaP) containing the
SCSI read or bidirectional command PDU. See Section 9.2 on
iSER Header Format for the iSCSI Control-Type PDU.
If the amount of unsolicited data to be transferred in a SCSI command
exceeds TargetRecvDataSegmentLength, then the iSCSI layer at the
initiator MUST segment the data into multiple iSCSI control-type
PDUs, with the data segment length in all PDUs generated except the
last one having exactly the size TargetRecvDataSegmentLength. The
data segment length of the last iSCSI control-type PDU carrying the
unsolicited data can be up to TargetRecvDataSegmentLength.
When the iSER layer at the target receives the SCSI command, it MUST
establish a Remote Mapping that associates the ITT to the Advertised
Write STag and the Read STag if present in the iSER header. The
Write STag is used by the iSER layer at the target in handling the
data transfer associated with the R2T PDU(s) as described in Section
7.3.6. The Read STag is used in handling the SCSI Data-in PDU(s)
from the iSCSI layer at the target as described in Section 7.3.5.
7.3.2. SCSI Response
Type: control-type PDU
PDU-specific qualifiers: DataDescriptorStatus
The iSCSI layer at the target MUST invoke the Send_Control
Operational Primitive qualified with DataDescriptorStatus, which
defines the buffer containing the sense and response information.
The iSCSI layer at the target MUST always return the SCSI status for
a SCSI command in a separate SCSI Response PDU. "Phase collapse" for
transferring SCSI status in a SCSI Data-in PDU MUST NOT be used. The
iSER layer at the target sends the SCSI Response PDU according to the
following rules:
* If no STags are Advertised by the initiator in the iSER Message
containing the SCSI command PDU, then the iSER layer at the target
MUST send a SendSE Message containing the SCSI Response PDU.
Ko, et al. Standards Track [Page 42]
RFC 5046 iSER Specification October 2007
* If the initiator Advertised a Read STag in the iSER Message
containing the SCSI Command PDU, then the iSER layer at the target
MUST send a SendInvSE Message containing the SCSI Response PDU.
The header of the SendInvSE Message MUST carry the Read STag to be
invalidated at the initiator.
* If the initiator Advertised only the Write STag in the iSER
Message containing the SCSI Command PDU, then the iSER layer at
the target MUST send a SendInvSE Message containing the SCSI
Response PDU. The header of the SendInvSE Message MUST carry the
Write STag to be invalidated at the initiator.
When the iSCSI layer at the target invokes the Send_Control
Operational Primitive to send the SCSI Response PDU, the iSER layer
at the target MUST invalidate the Remote Mapping that associates the
ITT to the Advertised STag(s) before transferring the SCSI Response
PDU to the initiator.
Upon receiving the SendInvSE Message containing the SCSI Response PDU
from the target, the RCaP layer at the initiator will invalidate the
STag specified in the header. The iSER layer at the initiator MUST
ensure that the correct STag is invalidated. If both the Read and
the Write STags are Advertised earlier by the initiator, then the
iSER layer at the initiator MUST explicitly invalidate the Write STag
upon receiving the SendInvSE Message because the header of the
SendInvSE Message can only carry one STag (in this case, the Read
STag) to be invalidated.
The iSER layer at the initiator MUST ensure the invalidation of the
STag(s) used in a command before notifying the iSCSI layer at the
initiator by invoking the Control_Notify Operational Primitive
qualified with the SCSI Response. This precludes the possibility of
using the STag(s) after the completion of the command, thereby
causing data corruption.
When the iSER layer at the initiator receives the SendSE or the
SendInvSE Message containing the SCSI Response PDU, it SHOULD
invalidate the Local Mapping that associates the ITT to the local
STag(s). The iSER layer MUST ensure that all local STag(s)
associated with the ITT are invalidated before notifying the iSCSI
layer of the SCSI Response PDU by invoking the Control_Notify
Operational Primitive qualified with the SCSI Response PDU.
Ko, et al. Standards Track [Page 43]
RFC 5046 iSER Specification October 2007
7.3.3. Task Management Function Request/Response
Type: control-type PDU
PDU-specific qualifiers (for TMF Request): DataDescriptorOut,
DataDescriptorIn
The iSER layer MUST use a SendSE Message to send the Task Management
Function Request/Response PDU.
For the Task Management Function Request with the TASK REASSIGN
function, the iSER layer at the initiator MUST do the following:
* It MUST use the ITT as specified in the Referenced Task Tag from
the Task Management Function Request PDU to locate the existing
STag(s), if any, in the Local Mapping(s) that associates the ITT
to the local STag(s).
* It MUST invalidate the existing STag(s), if any, and the Local
Mapping(s) that associates the ITT to the local STag(s).
* It MUST allocate a Read STag for the I/O Buffer as defined by the
qualifier DataDescriptorIn if the Send_Control Operational
Primitive invocation is qualified with DataDescriptorIn.
* It MUST allocate a Write STag for the I/O Buffer as defined by the
qualifier DataDescriptorOut if the Send_Control Operational
Primitive invocation is qualified with DataDescriptorOut.
* If STags are allocated, it MUST establish a new Local Mapping(s)
that associate the ITT to the allocated STag(s).
* It MUST Advertise the STags, if allocated, to the target in the
iSER header of the SendSE Message carrying the iSCSI PDU, as
described in Section 9.2.
For the Task Management Function Request with the TASK REASSIGN
function for a SCSI read or bidirectional command, the iSCSI layer at
the initiator MUST set ExpDataSN to 0 since the data transfer and
acknowledgements happen transparently to the iSCSI layer at the
initiator. This provides the flexibility to the iSCSI layer at the
target to request transmission of only the unacknowledged data as
specified in [RFC3720].
When the iSER layer at the target receives the Task Management
Function Request with the TASK REASSIGN function, it MUST do the
following:
Ko, et al. Standards Track [Page 44]
RFC 5046 iSER Specification October 2007
* It MUST use the ITT as specified in the Referenced Task Tag from
the Task Management Function Request PDU to locate the mappings
that associate the ITT to the Advertised STag(s) and the local
STag(s), if any.
* It MUST invalidate the local STag(s), if any, associated with the
ITT.
* It MUST replace the Advertised STag(s) in the Remote Mapping that
associates the ITT to the Advertised STag(s) with the Write STag
and the Read STag if present in the iSER header. The Write STag
is used in the handling of the R2T PDU(s) from the iSCSI layer at
the target as described in Section 7.3.6. The Read STag is used
in the handling of the SCSI Data-in PDU(s) from the iSCSI layer at
the target as described in Section 7.3.5.
7.3.4. SCSI Data-Out
Type: control-type PDU
PDU-specific qualifiers: DataDescriptorOut
The iSCSI layer at the initiator MUST invoke the Send_Control
Operational Primitive qualified with DataDescriptorOut, which defines
the initiator's I/O Buffer containing unsolicited SCSI Write data.
If the amount of unsolicited data to be transferred as SCSI Data-out
exceeds TargetRecvDataSegmentLength, then the iSCSI layer at the
initiator MUST segment the data into multiple iSCSI control-type
PDUs, with the DataSegmentLength having the value of
TargetRecvDataSegmentLength in all PDUs generated except the last
one. The DataSegmentLength of the last iSCSI control-type PDU
carrying the unsolicited data can be up to
TargetRecvDataSegmentLength. The iSCSI layer at the target MUST
perform the reassembly function for the unsolicited data.
For unsolicited data, if the F bit is set to 0 in a SCSI Data-out
PDU, the iSER layer at the initiator MUST use a Send Message to send
the SCSI Data-out PDU. If the F bit is set to 1, the iSER layer at
the initiator MUST use a SendSE Message to send the SCSI Data-out
PDU.
Note that for solicited data, the SCSI Data-out PDUs are not used
since R2T PDUs are not delivered to the iSCSI layer at the initiator;
instead, R2T PDUs are transformed by the iSER layer at the target
into RDMA Read operations. (See Section 7.3.6.)
Ko, et al. Standards Track [Page 45]
RFC 5046 iSER Specification October 2007
7.3.5. SCSI Data-In
Type: data-type PDU
PDU-specific qualifiers: DataDescriptorIn
When the iSCSI layer at the target is ready to return the SCSI Read
data to the initiator, it MUST invoke the Put_Data Operational
Primitive qualified with DataDescriptorIn, which defines the SCSI
Data-in buffer. See Section 7.1 on the general requirement on the
handling of iSCSI data-type PDUs. SCSI Data-in PDU(s) are used in
SCSI Read data transfer as described in Section 9.5.2.
The iSER layer at the target MUST do the following for each
invocation of the Put_Data Operational Primitive:
1. It MUST use the ITT in the SCSI Data-in PDU to locate the remote
Read STag in the Remote Mapping that associates the ITT to
Advertised STag(s). The Remote Mapping was established earlier
by the iSER layer at the target when the SCSI read command was
received from the initiator.
2. It MUST generate and send an RDMA Write Message containing the
read data to the initiator.
a. It MUST use the remote Read STag as the Data Sink STag of the
RDMA Write Message.
b. It MUST use the Buffer Offset from the SCSI Data-in PDU as
the Data Sink Tagged Offset of the RDMA Write Message.
c. It MUST use DataSegmentLength from the SCSI Data-in PDU to
determine the amount of data to be sent in the RDMA Write
Message.
3. It MUST associate DataSN and ITT from the SCSI Data-in PDU with
the RDMA Write operation. If the Put_Data Operational Primitive
invocation was qualified with Notify_Enable set, then when the
iSER layer at the target receives a completion from the RCaP
layer for the RDMA Write Message, the iSER layer at the target
MUST notify the iSCSI layer by invoking the
Data_Completion_Notify Operational Primitive qualified with
DataSN and ITT. Conversely, if the Put_Data Operational
Primitive invocation was qualified with Notify_Enable cleared,
then the iSER layer at the target MUST NOT notify the iSCSI layer
on completion and MUST NOT invoke the Data_Completion_Notify
Operational Primitive.
Ko, et al. Standards Track [Page 46]
RFC 5046 iSER Specification October 2007
When the A-bit is set to 1 in the SCSI Data-in PDU, the iSER layer at
the target MUST notify the iSCSI layer at the target when the data
transfer is complete at the initiator. To perform this additional
function, the iSER layer at the target can take advantage of the
operational ErrorRecoveryLevel if previously disclosed by the iSCSI
layer via an earlier invocation of the Notice_Key_Values Operational
Primitive. There are two approaches that can be taken:
1. If the iSER layer at the target knows that the operational
ErrorRecoveryLevel is 2, or if the iSER layer at the target does
not know the operational ErrorRecoveryLevel, then the iSER layer
at the target MUST issue a zero-length RDMA Read Request Message
following the RDMA Write Message. When the iSER layer at the
target receives a completion for the RDMA Read Request Message
from the RCaP layer, implying that the RDMA-Capable Controller at
the initiator has completed processing the RDMA Write Message due
to the completion ordering semantics of RCaP, the iSER layer at
the target MUST notify the iSCSI layer at the target by invoking
the Data_Ack_Notify Operational Primitive qualified with ITT and
DataSN (see Section 3.2.3).
2. If the iSER layer at the target knows that the operational
ErrorRecoveryLevel is 1, then the iSER layer at the target MUST
do one of the following:
a. It MUST notify the iSCSI layer at the target by invoking the
Data_Ack_Notify Operational Primitive qualified with ITT and
DataSN (see Section 3.2.3) when it receives the local
completion from the RCaP layer for the RDMA Write Message.
This is allowed since digest errors do not occur in iSER (see
Section 10.1.4.2) and a CRC error will cause the connection
to be terminated and the task to be terminated anyway. The
local RDMA Write completion from the RCaP layer guarantees
that the RCaP layer will not access the I/O Buffer again to
transfer the data associated with that RDMA Write operation.
b. Alternatively, it MUST use the same procedure for handling
the data transfer completion at the initiator as for
ErrorRecoveryLevel 2.
Note that the iSCSI layer at the target cannot set the A-bit to 1 if
the ErrorRecoveryLevel=0.
The SCSI status MUST always be returned in a separate SCSI Response
PDU. The S bit in the SCSI Data-in PDU MUST always be set to 0.
There MUST NOT be a "phase collapse" in the SCSI Data-in PDU.
Ko, et al. Standards Track [Page 47]
RFC 5046 iSER Specification October 2007
Since the RDMA Write Message only transfers the data portion of the
SCSI Data-in PDU but not the control information in the header, such
as ExpCmdSN, if timely updates of such information are crucial, the
iSCSI layer at the initiator MAY issue NOP-Out PDUs to request that
the iSCSI layer at the target respond with the information using NOP-
In PDUs.
7.3.6. Ready to Transfer (R2T)
Type: data-type PDU
PDU-specific qualifiers: DataDescriptorOut
In order to send an R2T PDU, the iSCSI layer at the target MUST
invoke the Get_Data Operational Primitive qualified with
DataDescriptorOut, which defines the I/O Buffer for receiving the
SCSI Write data from the initiator. See Section 7.1 on the general
requirements on the handling of iSCSI data-type PDUs.
The iSER layer at the target MUST do the following for each
invocation of the Get_Data Operational Primitive:
1. It MUST ensure a valid local STag for the I/O Buffer and a valid
Local Mapping that associates the Initiator Task Tag (ITT) to the
local STag. This may involve allocating a valid local STag and
establishing a Local Mapping.
2. It MUST use the ITT in the R2T to locate the remote Write STag in
the Remote Mapping that associates the ITT to Advertised STag(s).
The Remote Mapping is established earlier by the iSER layer at
the target when the iSER Message containing the Advertised Write
STag and the SCSI Command PDU for a SCSI write or bidirectional
command is received from the initiator.
3. If the iSER-ORD value at the target is set to 0, the iSER layer
at the target MUST terminate the connection and free up the
resources associated with the connection (as described in Section
5.2.3) if it receives the R2T PDU from the iSCSI layer at the
target. Upon termination of the connection, the iSER layer at
the target MUST notify the iSCSI layer at the target by invoking
the Connection_Terminate_Notify Operational Primitive.
4. If the iSER-ORD value at the target is set to greater than 0, the
iSER layer at the target MUST transform the R2T PDU into an RDMA
Read Request Message. While transforming the R2T PDU, the iSER
layer at the target MUST ensure that the number of outstanding
RDMA Read Request Messages does not exceed the iSER-ORD value.
To transform the R2T PDU, the iSER layer at the target:
Ko, et al. Standards Track [Page 48]
RFC 5046 iSER Specification October 2007
a. MUST derive the local STag and local Tagged Offset from the
DataDescriptorOut that qualified the Get_Data invocation.
b. MUST use the local STag as the Data Sink STag of the RDMA
Read Request Message.
c. MUST use the local Tagged Offset as the Data Sink Tagged
Offset of the RDMA Read Request Message.
d. MUST use the Desired Data Transfer Length from the R2T PDU as
the RDMA Read Message Size of the RDMA Read Request Message.
e. MUST use the remote Write STag as the Data Source STag of the
RDMA Read Request Message.
f. MUST use the Buffer Offset from the R2T PDU as the Data
Source Tagged Offset of the RDMA Read Request Message.
5. It MUST associate R2TSN and ITT from the R2T PDU with the RDMA
Read operation. If the Get_Data Operational Primitive invocation
is qualified with Notify_Enable set, then when the iSER layer at
the target receives a completion from the RCaP layer for the RDMA
Read operation, the iSER layer at the target MUST notify the
iSCSI layer by invoking the Data_Completion_Notify Operational
Primitive qualified with R2TSN and ITT. Conversely, if the
Get_Data Operational Primitive invocation is qualified with
Notify_Enable cleared, then the iSER layer at the target MUST NOT
notify the iSCSI layer on completion and MUST NOT invoke the
Data_Completion_Notify Operational Primitive.
When the RCaP layer at the initiator receives a valid RDMA Read
Request Message, it will return an RDMA Read Response Message
containing the solicited write data to the target. When the RCaP
layer at target receives the RDMA Read Response Message from the
initiator, it will place the solicited data in the I/O Buffer
referenced by the Data Sink STag in the RDMA Read Response Message.
Since the RDMA Read Request Message from the target does not transfer
the control information in the R2T PDU, such as ExpCmdSN, if timely
updates of such information are crucial, the iSCSI layer at the
initiator MAY issue NOP-Out PDUs to request that the iSCSI layer at
the target respond with the information using NOP-In PDUs.
Similarly, since the RDMA Read Response Message from the initiator
only transfers the data but not the control information normally
found in the SCSI Data-out PDU, such as ExpStatSN, if timely updates
of such information are crucial, the iSCSI layer at the target MAY
Ko, et al. Standards Track [Page 49]
RFC 5046 iSER Specification October 2007
issue NOP-In PDUs to request that the iSCSI layer at the initiator
respond with the information using NOP-Out PDUs.
7.3.7. Asynchronous Message
Type: control-type PDU
PDU-specific qualifiers: DataDescriptorSense
The iSCSI layer MUST invoke the Send_Control Operational Primitive
qualified with DataDescriptorSense, which defines the buffer
containing the sense and iSCSI Event information. The iSER layer
MUST use a SendSE Message to send the Asynchronous Message PDU.
7.3.8. Text Request and Text Response
Type: control-type PDU
PDU-specific qualifiers: DataDescriptorTextOut (for Text
Request), DataDescriptorIn (for Text Response)
The iSCSI layer MUST invoke the Send_Control Operational Primitive
qualified with DataDescriptorTextOut (or DataDescriptorIn), which
defines the Text Request (or Text Response) buffer. The iSER layer
MUST use SendSE Messages to send the Text Request (or Text Response
PDUs).
7.3.9. Login Request and Login Response
During the login negotiation, the iSCSI layer interacts with the
transport layer directly and the iSER layer is not involved. See
Section 5.1 on iSCSI/iSER connection setup. If the underlying
transport is TCP, the Login Request PDUs and the Login Response PDUs
are exchanged when the connection between the initiator and the
target is still in the byte stream mode.
The iSCSI layer MUST not send a Login Request (or a Login Response)
PDU during the Full Feature Phase. A Login Request (or a Login
Response) PDU, if used, MUST be treated as an iSCSI protocol error.
The iSER layer MAY reject such a PDU from the iSCSI layer with an
appropriate error code. If a Login Request PDU is received by the
iSCSI layer at the target, it MUST respond with a Reject PDU with a
reason code of "protocol error".
Ko, et al. Standards Track [Page 50]
RFC 5046 iSER Specification October 2007
7.3.10. Logout Request and Logout Response
Type: control-type PDU
PDU-specific qualifiers: None
The iSER layer MUST use a SendSE Message to send the Logout Request
or Logout Response PDU. Sections 5.2.1 and 5.2.2 describe the
handling of the Logout Request and the Logout Response at the
initiator and the target and the interactions between the initiator
and the target to terminate a connection.
7.3.11. SNACK Request
Since HeaderDigest and DataDigest must be negotiated to "None", there
are no digest errors when the connection is in iSER-assisted mode.
Also, since RCaP delivers all messages in the order they were sent,
there are no sequence errors when the connection is in iSER-assisted
mode. Therefore, the iSCSI layer MUST NOT send SNACK Request PDUs.
A SNCAK Request PDU, if used, MUST be treated as an iSCSI protocol
error. The iSER layer MAY reject such a PDU from the iSCSI layer
with an appropriate error code. If a SNACK Request PDU is received
by the iSCSI layer at the target, it MUST respond with a Reject PDU
with a reason code of "protocol error".
7.3.12. Reject
Type: control-type PDU
PDU-specific qualifiers: DataDescriptorReject
The iSCSI layer MUST invoke the Send_Control Operational Primitive
qualified with DataDescriptorReject, which defines the Reject buffer.
The iSER layer MUST use a SendSE Message to send the Reject PDU.
7.3.13. NOP-Out and NOP-In
Type: control-type PDU
PDU-specific qualifiers: DataDescriptorNOPOut (for NOP-Out),
DataDescriptorNOPIn (for NOP-In)
The iSCSI layer MUST invoke the Send_Control Operational Primitive
qualified with DataDescriptorNOPOut (or DataDescriptorNOPIn), which
defines the Ping (or Return Ping) data buffer. The iSER layer MUST
use SendSE Messages to send the NOP-Out (or NOP-In) PDU.
Ko, et al. Standards Track [Page 51]
RFC 5046 iSER Specification October 2007
8. Flow Control and STag Management
8.1. Flow Control for RDMA Send Message Types
Send Message Types in RCaP are used by the iSER layer to transfer
iSCSI control-type PDUs. Each Send Message Type in RCaP consumes an
Untagged Buffer at the Data Sink. However, neither the RCaP layer
nor the iSER layer provides an explicit flow control mechanism for
the Send Message Types. Therefore, the iSER layer SHOULD provision
enough Untagged buffers for handling incoming Send Message Types to
prevent buffer exhaustion at the RCaP layer. If buffer exhaustion
occurs, it may result in the termination of the connection.
An implementation may choose to satisfy the buffer requirement by
using a common buffer pool shared across multiple connections, with
usage limits on a per-connection basis and usage limits on the buffer
pool itself. In such an implementation, exceeding the buffer usage
limit for a connection or the buffer pool itself may trigger
interventions from the iSER layer to replenish the buffer pool and/or
to isolate the connection causing the problem.
iSER also provides the MaxOutstandingUnexpectedPDUs key to be used by
the initiator and the target to declare the maximum number of
outstanding "unexpected" control-type PDUs that it can receive. It
is intended to allow the receiving side to determine the amount of
buffer resources needed beyond the normal flow control mechanism
available in iSCSI.
The buffer resources required at both the initiator and the target as
a result of control-type PDUs sent by the initiator is described in
Section 8.1.1. The buffer resources required at both the initiator
and target as a result of control-type PDUs sent by the target is
described in Section 8.1.2.
8.1.1. Flow Control for Control-Type PDUs from the Initiator
The control-type PDUs that can be sent by an initiator to a target
can be grouped into the following categories:
1. Regulated: Control-type PDUs in this category are regulated by
the iSCSI CmdSN window mechanism and the immediate flag is not
set.
2. Unregulated but Expected: Control-type PDUs in this category are
not regulated by the iSCSI CmdSN window mechanism but are
expected by the target.
Ko, et al. Standards Track [Page 52]
RFC 5046 iSER Specification October 2007
3. Unregulated and Unexpected: Control-type PDUs in this category
are not regulated by the iSCSI CmdSN window mechanism and are
"unexpected" by the target.
8.1.1.1. Control-Type PDUs from the Initiator in the Regulated Category
Control-type PDUs that can be sent by the initiator in this category
are regulated by the iSCSI CmdSN window mechanism and the immediate
flag is not set.
The queuing capacity required of the iSCSI layer at the target is
described in Section 3.2.2.1 of [RFC3720]. For each of the control-
type PDUs that can be sent by the initiator in this category, the
initiator MUST provision for the buffer resources required for the
corresponding control-type PDU sent as a response from the target.
The following is a list of the PDUs that can be sent by the initiator
and the PDUs that are sent by the target in response:
a. When an initiator sends a SCSI Command PDU, it expects a SCSI
Response PDU from the target.
b. When the initiator sends a Task Management Function Request
PDU, it expects a Task Management Function Response PDU from
the target.
c. When the initiator sends a Text Request PDU, it expects a
Text Response PDU from the target.
d. When the initiator sends a Logout Request PDU, it expects a
Logout Response PDU from the target.
e. When the initiator sends a NOP-Out PDU as a ping request with
ITT != 0xffffffff and TTT = 0xffffffff, it expects a NOP-In
PDU from the target with the same ITT and TTT as in the ping
request.
The response from the target for any of the PDUs enumerated here may
alternatively be in the form of a Reject PDU sent instead before the
task is active, as described in Section 6.3 of [RFC3720].
8.1.1.2. Control-Type PDUs from the Initiator in the Unregulated but
Expected Category
For the control-type PDUs in the Unregulated but Expected category,
the amount of buffering resources required at the target can be
predetermined. The following is a list of the PDUs in this category:
Ko, et al. Standards Track [Page 53]
RFC 5046 iSER Specification October 2007
a. SCSI Data-out PDUs are used by the initiator to send
unsolicited data. The amount of buffer resources required by
the target can be determined using FirstBurstLength. Note
that SCSI Data-out PDUs are not used for solicited data since
the R2T PDU that is used for solicitation is transformed into
RDMA Read operations by the iSER layer at the target. See
Section 7.3.4.
b. A NOP-Out PDU with TTT != 0xffffffff is sent as a ping
response by the initiator to the NOP-In PDU sent as a ping
request by the target.
8.1.1.3. Control-Type PDUs from the Initiator in the Unregulated and
Unexpected Category
PDUs in the Unregulated and Unexpected category are PDUs with the
immediate flag set. The number of PDUs in this category that can be
sent by an initiator is controlled by the value of
MaxOutstandingUnexpectedPDUs declared by the target (see Section
6.7). After a PDU in this category is sent by the initiator, it is
outstanding until it is retired. At any time, the number of
outstanding unexpected PDUs MUST not exceed the value of
MaxOutstandingUnexpectedPDUs declared by the target.
The target uses the value of MaxOutstandingUnexpectedPDUs that it
declared to determine the amount of buffer resources required for
control-type PDUs in this category that can be sent by an initiator.
For the initiator, for each of the control-type PDUs that can be sent
in this category, the initiator MUST provision for the buffer
resources if required for the corresponding control-type PDU that can
be sent as a response from the target.
An outstanding PDU in this category is retired as follows. If the
CmdSN of the PDU sent by the initiator in this category is x, the PDU
is outstanding until the initiator sends a non-immediate control-type
PDU on the same connection with CmdSN = y (where y is at least x) and
the target responds with a control-type PDU on any connection where
ExpCmdSN is at least y+1.
When the number of outstanding unexpected control-type PDUs equals
MaxOutstandingUnexpectedPDUs, the iSCSI layer at the initiator MUST
NOT generate any unexpected PDUs that otherwise it would have
generated, even if it is intended for immediate delivery.
Ko, et al. Standards Track [Page 54]
RFC 5046 iSER Specification October 2007
8.1.2. Flow Control for Control-Type PDUs from the Target
Control-type PDUs that can be sent by a target and are expected by
the initiator are listed in the Regulated category (see Section
8.1.1.1).
For the control-type PDUs that can be sent by a target and are
unexpected by the initiator, the number is controlled by
MaxOutstandingUnexpectedPDUs declared by the initiator (see Section
6.7). After a PDU in this category is sent by a target, it is
outstanding until it is retired. At any time, the number of
outstanding unexpected PDUs MUST not exceed the value of
MaxOutstandingUnexpectedPDUs declared by the initiator. The
initiator uses the value of MaxOutstandingUnexpectedPDUs that it
declared to determine the amount of buffer resources required for
control-type PDUs in this category that can be sent by a target. The
following is a list of the PDUs in this category and the conditions
for retiring the outstanding PDU:
a. For an Asynchronous Message PDU with StatSN = x, the PDU is
outstanding until the initiator sends a control-type PDU with
ExpStatSN set to at least x+1.
b. For a Reject PDU with StatSN = x that is sent after a task is
active, the PDU is outstanding until the initiator sends a
control-type PDU with ExpStatSN set to at least x+1.
c. For a NOP-In PDU with ITT = 0xffffffff and StatSN = x, the
PDU is outstanding until the initiator responds with a
control-type PDU on the same connection where ExpStatSN is at
least x+1. But if the NOP-In PDU is sent as a ping request
with TTT != 0xffffffff, the PDU can also be retired when the
initiator sends a NOP-Out PDU with the same ITT and TTT as in
the ping request. Note that when a target sends a NOP-In PDU
as a ping request, it must provision a buffer for the NOP-Out
PDU sent as a ping response from the initiator.
When the number of outstanding unexpected control-type PDUs equals
MaxOutstandingUnexpectedPDUs, the iSCSI layer at the target MUST NOT
generate any unexpected PDUs that otherwise it would have generated,
even if its intent is to indicate an iSCSI error condition (e.g.,
Asynchronous Message, Reject). Task timeouts, as in the initiator
waiting for a command completion or other connection and session
level exceptions, will ensure that correct operational behavior will
result in these cases despite not generating the PDU. This rule
overrides any other requirements elsewhere that require that a Reject
PDU MUST be sent.
Ko, et al. Standards Track [Page 55]
RFC 5046 iSER Specification October 2007
(Implementation note: A SCSI task timeout and recovery can be a
lengthy process and hence SHOULD be avoided by proper provisioning of
resources.)
(Implementation note: To ensure that the initiator has a means to
inform the target that outstanding PDUs have been retired, the target
should reserve the last unexpected control-type PDU allowable by the
value of MaxOutstandingUnexpectedPDUs declared by the initiator for
sending a NOP-In ping request with TTT != 0xffffffff to allow the
initiator to return the NOP-Out ping response with the current
ExpStatSN.)
8.2. Flow Control for RDMA Read Resources
The total number of RDMA Read operations that can be active
simultaneously on an iSCSI/iSER connection depends on the amount of
resources allocated as declared in the iSER Hello exchange described
in Section 5.1.3. Exceeding the number of RDMA Read operations
allowed on a connection will result in the connection being
terminated by the RCaP layer. The iSER layer at the target maintains
the iSER-ORD to keep track of the maximum number of RDMA Read
Requests that can be issued by the iSER layer on a particular RCaP
Stream.
During connection setup (see Section 5.1), iSER-IRD is known at the
initiator and iSER-ORD is known at the target after the iSER layers
at the initiator and the target have respectively allocated the
connection resources necessary to support RCaP, as directed by the
Allocate_Connection_Resources Operational Primitive from the iSCSI
layer before the end of the iSCSI Login Phase. In the Full Feature
Phase, the first message sent by the initiator is the iSER Hello
Message (see Section 9.3), which contains the value of iSER-IRD. In
response to the iSER Hello Message, the target sends the iSER
HelloReply Message (see Section 9.4), which contains the value of
iSER-ORD. The iSER layer at both the initiator and the target MAY
adjust (lower) the resources associated with iSER-IRD and iSER-ORD
respectively to match the iSER-ORD value declared in the HelloReply
Message. The iSER layer at the target MUST flow control the RDMA
Read Request Messages to not exceed the iSER-ORD value at the target.
8.3. STag Management
An STag, as defined in [RDMAP], is an identifier of a Tagged Buffer
used in an RDMA operation. The allocation and the subsequent
invalidation of the STags are specified in this document if the STags
are exposed on the wire by being Advertised in the iSER header or
declared in the header of an RCaP Message.
Ko, et al. Standards Track [Page 56]
RFC 5046 iSER Specification October 2007
8.3.1. Allocation of STags
When the iSCSI layer at the initiator invokes the Send_Control
Operational Primitive to request that the iSER layer at the initiator
process a SCSI command, zero, one, or two STags may be allocated by
the iSER layer. See Section 7.3.1 for details. The number of STags
allocated depends on whether the command is unidirectional or
bidirectional and whether or not solicited write data transfer is
involved.
When the iSCSI layer at the initiator invokes the Send_Control
Operational Primitive to request that the iSER layer at the initiator
process a Task Management Function Request with the TASK REASSIGN
function, besides allocating zero, one, or two STags, the iSER layer
MUST invalidate the existing STags, if any, associated with the ITT.
See Section 7.3.3 for details.
The iSER layer at the target allocates a local Data Sink STag when
the iSCSI layer at the target invokes the Get_Data Operational
Primitive to request that the iSER layer process an R2T PDU. See
Section 7.3.6 for details.
8.3.2. Invalidation of STags
The invalidation of the STags at the initiator at the completion of a
unidirectional or bidirectional command when the associated SCSI
Response PDU is sent by the target is described in Section 7.3.2.
When a unidirectional or bidirectional command concludes without the
associated SCSI Response PDU being sent by the target, the iSCSI
layer at the initiator MUST request that the iSER layer at the
initiator invalidate the STags by invoking the
Deallocate_Task_Resources Operational Primitive qualified with ITT.
In response, the iSER layer at the initiator MUST locate the STag(s)
(if any) in the Local Mapping that associates the ITT to the local
STag(s). The iSER layer at the initiator MUST invalidate the STag(s)
(if any) and the Local Mapping.
For an RDMA Read operation used to realize a SCSI Write data
transfer, the iSER layer at the target SHOULD invalidate the Data
Sink STag at the conclusion of the RDMA Read operation referencing
the Data Sink STag (to permit the immediate reuse of buffer
resources).
For an RDMA Write operation used to realize a SCSI Read data
transfer, the Data Source STag at the target is not declared to the
initiator and is not exposed on the wire. Invalidation of the STag
is thus not specified.
Ko, et al. Standards Track [Page 57]
RFC 5046 iSER Specification October 2007
When a unidirectional or bidirectional command concludes without the
associated SCSI Response PDU being sent by the target, the iSCSI
layer at the target MUST request that the iSER layer at the target
invalidate the STags by invoking the Deallocate_Task_Resources
Operational Primitive qualified with ITT. In response, the iSER
layer at the target MUST locate the local STag(s) (if any) in the
Local Mapping that associates the ITT to the local STag(s). The iSER
layer at the target MUST invalidate the local STag(s) (if any) and
the mapping.
9. iSER Control and Data Transfer
For iSCSI data-type PDUs (see Section 7.1), the iSER layer uses RDMA
Read and RDMA Write operations to transfer the solicited data. For
iSCSI control-type PDUs (see Section 7.2), the iSER layer uses Send
Message Types of RCaP.
9.1. iSER Header Format
An iSER header MUST be present in every Send Message Type of RCaP.
The iSER header is located in the first 12 bytes of the message
payload of the Send Message Type of RCaP, as shown in Figure 2.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Opcode| Opcode Specific Fields |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Opcode Specific Fields |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Opcode Specific Fields |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2. iSER Header Format
Opcode - Operation Code: 4 bits
The Opcode field identifies the type of iSER Messages:
0001b = iSCSI control-type PDU
0010b = iSER Hello Message
0011b = iSER HelloReply Message
All other opcodes are reserved.
Ko, et al. Standards Track [Page 58]
RFC 5046 iSER Specification October 2007
9.2. iSER Header Format for the iSCSI Control-Type PDU
The iSER layer uses Send Message Types of RCaP to transfer iSCSI
control-type PDUs (see Section 7.2). The message payload of each of
the Send Message Types of RCaP used for transferring an iSER Message
contains an iSER Header followed by an iSCSI control-type PDU.
The iSER header in a Send Message Type of RCaP carrying an iSCSI
control-type PDU MUST have the format as described in Figure 3.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |W|R| |
| 0001b |S|S| Reserved |
| |V|V| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Write STag (or N/A) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Read STag (or N/A) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3. iSER Header Format for iSCSI Control-Type PDU
WSV - Write STag Valid flag: 1 bit
This flag indicates the validity of the Write STag field of the
iSER Header. If set to one, the Write STag field in this iSER
Header is valid. If set to zero, the Write STag field in this
iSER Header MUST be ignored at the receiver. The Write STag
Valid flag is set to one when there is solicited data to be
transferred for a SCSI write or bidirectional command, or when
there are non-immediate unsolicited and solicited data to be
transferred for the referenced task specified in a Task
Management Function Request with the TASK REASSIGN function.
RSV - Read STag Valid flag: 1 bit
This flag indicates the validity of the Read STag field of the
iSER Header. If set to one, the Read STag field in this iSER
Header is valid. If set to zero, the Read STag field in this
iSER Header MUST be ignored at the receiver. The Read STag Valid
flag is set to one for a SCSI read or bidirectional command, or
for a Task Management Function Request with the TASK REASSIGN
function.
Ko, et al. Standards Track [Page 59]
RFC 5046 iSER Specification October 2007
Write STag - Write Steering Tag: 32 bits
This field contains the Write STag when the Write STag Valid flag
is set to one. For a SCSI write or bidirectional command, the
Write STag is used to Advertise the initiator's I/O Buffer
containing the solicited data. For a Task Management Function
Request with the TASK REASSIGN function, the Write STag is used
to Advertise the initiator's I/O Buffer containing the non-
immediate unsolicited data and solicited data. This Write STag
is used as the Data Source STag in the resultant RDMA Read
operation(s). When the Write STag Valid flag is set to zero,
this field MUST be set to zero.
Read STag - Read Steering Tag: 32 bits
This field contains the Read STag when the Read STag Valid flag
is set to one. The Read STag is used to Advertise the
initiator's Read I/O Buffer of a SCSI read or bidirectional
command, or of a Task Management Function Request with the TASK
REASSIGN function. This Read STag is used as the Data Sink STag
in the resultant RDMA Write operation(s). When the Read STag
Valid flag is zero, this field MUST be set to zero.
Reserved:
Reserved fields MUST be set to zero on transmit and MUST be
ignored on reception.
9.3. iSER Header Format for the iSER Hello Message
An iSER Hello Message MUST only contain the iSER header, which MUST
have the format as described in Figure 4. The iSER Hello Message is
the first iSER Message sent on the RCaP Stream from the iSER layer at
the initiator to the iSER layer at the target.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | | | | |
| 0010b | Rsvd | MaxVer| MinVer| iSER-IRD |
| | | | | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4. iSER Header Format for iSER Hello Message
Ko, et al. Standards Track [Page 60]
RFC 5046 iSER Specification October 2007
MaxVer - Maximum Version: 4 bits
This field specifies the maximum version of the iSER protocol
supported. It MUST be set to one to indicate the version of the
specification described in this document.
MinVer - Minimum Version: 4 bits
This field specifies the minimum version of the iSER protocol
supported. It MUST be set to one to indicate the version of the
specification described in this document.
iSER-IRD: 16 bits
This field contains the value of the iSER-IRD at the initiator.
Reserved (Rsvd):
Reserved fields MUST be set to zero on transmit, and MUST be
ignored on reception.
9.4. iSER Header Format for the iSER HelloReply Message
An iSER HelloReply Message MUST only contain the iSER header which
MUST have the format as described in Figure 5. The iSER HelloReply
Message is the first iSER Message sent on the RCaP Stream from the
iSER layer at the target to the iSER layer at the initiator.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |R| | | |
| 0011b |Rsvd |E| MaxVer| CurVer| iSER-ORD |
| | |J| | | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5. iSER Header Format for iSER HelloReply Message
REJ - Reject flag: 1 bit
This flag indicates whether the target is rejecting this
connection. If set to one, the target is rejecting the
connection.
Ko, et al. Standards Track [Page 61]
RFC 5046 iSER Specification October 2007
MaxVer - Maximum Version: 4 bits
This field specifies the maximum version of the iSER protocol
supported. It MUST be set to one to indicate the version of the
specification described in this document.
CurVer - Current Version: 4 bits
This field specifies the current version of the iSER protocol
supported. It MUST be set to one to indicate the version of the
specification described in this document.
iSER-ORD: 16 bits
This field contains the value of the iSER-ORD at the target.
Reserved (Rsvd):
Reserved fields MUST be set to zero on transmit, and MUST be
ignored on reception.
9.5. SCSI Data Transfer Operations
The iSER layer at the initiator and the iSER layer at the target
handle each SCSI Write, SCSI Read, and bidirectional operation as
described below.
9.5.1. SCSI Write Operation
The iSCSI layer at the initiator MUST invoke the Send_Control
Operational Primitive to request that the iSER layer at the initiator
send the SCSI write command. The iSER layer at the initiator MUST
request that the RCaP layer transmit a SendSE Message with the
message payload consisting of the iSER header followed by the SCSI
Command PDU and immediate data (if any). If there is solicited data,
the iSER layer MUST Advertise the Write STag in the iSER header of
the SendSE Message, as described in Section 9.2. Upon receiving the
SendSE Message, the iSER layer at the target MUST notify the iSCSI
layer at the target by invoking the Control_Notify Operational
Primitive qualified with the SCSI Command PDU. See Section 7.3.1 for
details on the handling of the SCSI write command.
For the non-immediate unsolicited data, the iSCSI layer at the
initiator MUST invoke a Send_Control Operational Primitive qualified
with the SCSI Data-out PDU. Upon receiving each Send or SendSE
Message containing the non-immediate unsolicited data, the iSER layer
at the target MUST notify the iSCSI layer at the target by invoking
the Control_Notify Operational Primitive qualified with the SCSI
Ko, et al. Standards Track [Page 62]
RFC 5046 iSER Specification October 2007
Data-out PDU. See Section 7.3.4 for details on the handling of the
SCSI Data-out PDU.
For the solicited data, when the iSCSI layer at the target has an I/O
Buffer available, it MUST invoke the Get_Data Operational Primitive
qualified with the R2T PDU. See Section 7.3.6 for details on the
handling of the R2T PDU.
When the data transfer associated with this SCSI Write operation is
complete, the iSCSI layer at the target MUST invoke the Send_Control
Operational Primitive when it is ready to send the SCSI Response PDU.
Upon receiving a SendSE or SendInvSE Message containing the SCSI
Response PDU, the iSER layer at the initiator MUST notify the iSCSI
layer at the initiator by invoking the Control_Notify Operational
Primitive qualified with the SCSI Response PDU. See Section 7.3.2
for details on the handling of the SCSI Response PDU.
9.5.2. SCSI Read Operation
The iSCSI layer at the initiator MUST invoke the Send_Control
Operational Primitive to request that the iSER layer at the initiator
to send the SCSI read command. The iSER layer at the initiator MUST
request that the RCaP layer transmit a SendSE Message with the
message payload consisting of the iSER header followed by the SCSI
Command PDU. The iSER layer at the initiator MUST Advertise the Read
STag in the iSER header of the SendSE Message, as described in
Section 9.2. Upon receiving the SendSE Message, the iSER layer at
the target MUST notify the iSCSI layer at the target by invoking the
Control_Notify Operational Primitive qualified with the SCSI Command
PDU. See Section 7.3.1 for details on the handling of the SCSI read
command.
When the requested SCSI data is available in the I/O Buffer, the
iSCSI layer at the target MUST invoke the Put_Data Operational
Primitive qualified with the SCSI Data-in PDU. See Section 7.3.5 for
details on the handling of the SCSI Data-in PDU.
When the data transfer associated with this SCSI Read operation is
complete, the iSCSI layer at the target MUST invoke the Send_Control
Operational Primitive when it is ready to send the SCSI Response PDU.
Upon receiving the SendInvSE Message containing the SCSI Response
PDU, the iSER layer at the initiator MUST notify the iSCSI layer at
the initiator by invoking the Control_Notify Operational Primitive
qualified with the SCSI Response PDU. See Section 7.3.2 for details
on the handling of the SCSI Response PDU.
Ko, et al. Standards Track [Page 63]
RFC 5046 iSER Specification October 2007
9.5.3. Bidirectional Operation
The initiator and the target handle the SCSI Write and the SCSI Read
portions of this bidirectional operation the same as described in
Sections 9.5.1 and 9.5.2, respectively.
10. iSER Error Handling and Recovery
RCaP provides the iSER layer with reliable in-order delivery.
Therefore, the error management needs of an iSER-assisted connection
are somewhat different than those of a Traditional iSCSI connection.
10.1. Error Handling
iSER error handling is described in the following sections,
classified loosely based on the sources of errors:
1. Those originating at the transport layer (e.g., TCP).
2. Those originating at the RCaP layer.
3. Those originating at the iSER layer.
4. Those originating at the iSCSI layer.
10.1.1. Errors in the Transport Layer
If the transport layer is TCP, then TCP packets with detected errors
are silently dropped by the TCP layer and result in retransmission at
the TCP layer. This has no impact on the iSER layer. However,
connection loss (e.g., link failure) and unexpected termination
(e.g., TCP graceful or abnormal close without the iSCSI Logout
exchanges) at the transport layer will cause the iSCSI/iSER
connection to be terminated as well.
10.1.1.1. Failure in the Transport Layer before RCaP Mode Is Enabled
If the connection is lost or terminated before the iSCSI layer
invokes the Allocate_Connection_Resources Operational Primitive, the
login process is terminated and no further action is required.
If the connection is lost or terminated after the iSCSI layer has
invoked the Allocate_Connection_Resources Operational Primitive, then
the iSCSI layer MUST request that the iSER layer deallocate all
connection resources by invoking the Deallocate_Connection_Resources
Operational Primitive.
Ko, et al. Standards Track [Page 64]
RFC 5046 iSER Specification October 2007
10.1.1.2. Failure in the Transport Layer after RCaP Mode Is Enabled
If the connection is lost or terminated after the iSCSI layer has
invoked the Enable_Datamover Operational Primitive, the iSER layer
MUST notify the iSCSI layer of the connection loss by invoking the
Connection_Terminate_Notify Operational Primitive. Prior to invoking
the Connection_Terminate_Notify Operational Primitive, the iSER layer
MUST perform the actions described in Section 5.2.3.2.
10.1.2. Errors in the RCaP Layer
The RCaP layer does not have error recovery operations built in. If
errors are detected at the RCaP layer, the RCaP layer will terminate
the RCaP Stream and the associated connection.
10.1.2.1. Errors Detected in the Local RCaP Layer
If an error is encountered at the local RCaP layer, the RCaP layer
MAY send a Terminate Message to the Remote Peer to report the error
if possible. (For iWARP, see [RDMAP] for the list of errors where a
Terminate Message is sent.) The RCaP layer is responsible for
terminating the connection. After the RCaP layer notifies the iSER
layer that the connection is terminated, the iSER layer MUST notify
the iSCSI layer by invoking the Connection_Terminate_Notify
Operational Primitive. Prior to invoking the
Connection_Terminate_Notify Operational Primitive, the iSER layer
MUST perform the actions described in Section 5.2.3.2.
10.1.2.2. Errors Detected in the RCaP Layer at the Remote Peer
If an error is encountered at the RCaP layer at the Remote Peer, the
RCaP layer at the Remote Peer may send a Terminate Message to report
the error if possible. If it is unable to send the Terminate
Message, the connection is terminated. This is treated the same as a
failure in the transport layer after RDMA is enabled as described in
Section 10.1.1.2.
If an error is encountered at the RCaP layer at the Remote Peer and
it is able to send a Terminate Message, the RCaP layer at the Remote
Peer is responsible for terminating the connection. After the local
RCaP layer notifies the iSER layer that the connection is terminated,
the iSER layer MUST notify the iSCSI layer by invoking the
Connection_Terminate_Notify Operational Primitive. Prior to invoking
the Connection_Terminate_Notify Operational Primitive, the iSER layer
MUST perform the actions described in Section 5.2.3.2.
Ko, et al. Standards Track [Page 65]
RFC 5046 iSER Specification October 2007
10.1.3. Errors in the iSER Layer
The error handling due to errors at the iSER layer is described in
the following sections.
10.1.3.1. Insufficient Connection Resources to Support RCaP at
Connection Setup
After the iSCSI layer at the initiator invokes the
Allocate_Connection_Resources Operational Primitive during the iSCSI
Login Negotiation Phase, if the iSER layer at the initiator fails to
allocate the connection resources necessary to support RCaP, it MUST
return a status of failure to the iSCSI layer at the initiator. The
iSCSI layer at the initiator MUST terminate the connection as
described in Section 5.2.3.1.
After the iSCSI layer at the target invokes the
Allocate_Connection_Resources Operational Primitive during the iSCSI
Login Negotiation Phase, if the iSER layer at the target fails to
allocate the connection resources necessary to support RCaP, it MUST
return a status of failure to the iSCSI layer at the target. The
iSCSI layer at the target MUST send a Login Response with a status
class of 3 (Target Error), and a status code of "0302" (Out of
Resources). The iSCSI layers at the initiator and the target MUST
terminate the connection as described in Section 5.2.3.1.
10.1.3.2. iSER Negotiation Failures
If the RCaP or iSER related parameters declared by the initiator in
the iSER Hello Message are unacceptable to the iSER layer at the
target, the iSER layer at the target MUST set the Reject (REJ) flag,
as described in Section 9.4, in the iSER HelloReply Message. The
following are the cases when the iSER layer MUST set the REJ flag to
one in the HelloReply Message:
* The initiator-declared iSER-IRD value is greater than 0 and the
target-declared iSER-ORD value is 0.
* The initiator-supported and the target-supported iSER protocol
versions do not overlap.
After requesting that the RCaP layer send the iSER HelloReply
Message, the handling of the error situation is the same as that for
iSER format errors as described in Section 10.1.3.3.
Ko, et al. Standards Track [Page 66]
RFC 5046 iSER Specification October 2007
10.1.3.3. iSER Format Errors
The following types of errors in an iSER header are considered format
errors:
* Illegal contents of any iSER header field
* Inconsistent field contents in an iSER header
* Length error for an iSER Hello or HelloReply Message (see Section
9.3 and 9.4)
When a format error is detected, the following events MUST occur in
the specified sequence:
1. The iSER layer MUST request that the RCaP layer terminate the
RCaP Stream. The RCaP layer MUST terminate the associated
connection.
2. The iSER layer MUST notify the iSCSI layer of the connection
termination by invoking the Connection_Terminate_Notify
Operational Primitive. Prior to invoking the
Connection_Terminate_Notify Operational Primitive, the iSER layer
MUST perform the actions described in Section 5.2.3.2.
10.1.3.4. iSER Protocol Errors
The first iSER Message sent by the iSER layer at the initiator after
transitioning into iSER-assisted mode MUST be the iSER Hello Message
(see Section 9.3). Likewise, the first iSER Message sent by the iSER
layer at the target after transitioning into iSER-assisted mode MUST
be the iSER HelloReply Message (see Section 9.4). Failure to send
the iSER Hello or HelloReply Message, as indicated by the wrong
Opcode in the iSER header, is a protocol error. The handling of this
error situation is the same as that for iSER format errors as
described in Section 10.1.3.3.
If the sending side of an iSER-enabled connection acts in a manner
not permitted by the negotiated or declared login/text operational
key values as described in Section 6, this is a protocol error, and
the receiving side MAY handle this the same as for iSER format errors
as described in Section 10.1.3.3.
10.1.4. Errors in the iSCSI Layer
The error handling due to errors at the iSCSI layer is described in
the following sections. For error recovery, see Section 10.2.
Ko, et al. Standards Track [Page 67]
RFC 5046 iSER Specification October 2007
10.1.4.1. iSCSI Format Errors
When an iSCSI format error is detected, the iSCSI layer MUST request
that the iSER layer terminate the RCaP Stream by invoking the
Connection_Terminate Operational Primitive. For more details on the
connection termination, see Section 5.2.3.1.
10.1.4.2. iSCSI Digest Errors
In the iSER-assisted mode, the iSCSI layer will not see any digest
error because both the HeaderDigest and the DataDigest keys are
negotiated to "None".
10.1.4.3. iSCSI Sequence Errors
For Traditional iSCSI, sequence errors are caused by dropped PDUs due
to header or data digest errors. Since digests are not used in
iSER-assisted mode and the RCaP layer will deliver all messages in
the order they were sent, sequence errors will not occur in iSER-
assisted mode.
10.1.4.4. iSCSI Protocol Error
When the iSCSI layer handles certain protocol errors by dropping the
connection, the error handling is the same as that for iSCSI format
errors as described in Section 10.1.4.1.
When the iSCSI layer uses the iSCSI Reject PDU and response codes to
handle certain other protocol errors, no special handling at the iSER
layer is required.
10.1.4.5. SCSI Timeouts and Session Errors
SCSI Timeouts and Session Errors are handled at the iSCSI layer and
no special handling at the iSER layer is required.
10.1.4.6. iSCSI Negotiation Failures
For negotiation failures that happen during the Login Phase at the
initiator after the iSCSI layer has invoked the
Allocate_Connection_Resources Operational Primitive and before the
Enable_Datamover Operational Primitive has been invoked, the iSCSI
layer MUST request that the iSER layer deallocate all connection
resources by invoking the Deallocate_Connection_Resources Operational
Primitive. The iSCSI layer at the initiator MUST terminate the
connection.
Ko, et al. Standards Track [Page 68]
RFC 5046 iSER Specification October 2007
For negotiation failures during the Login Phase at the target, the
iSCSI layer can use a Login Response with a status class other than 0
(success) to terminate the Login Phase. If the iSCSI layer has
invoked the Allocate_Connection_Resources Operational Primitive
before the Enable_Datamover Operational Primitive has been invoked,
the iSCSI layer at the target MUST request that the iSER layer at the
target deallocate all connection resources by invoking the
Deallocate_Connection_Resources Operational Primitive. The iSCSI
layer at both the initiator and the target MUST terminate the
connection.
During the iSCSI Login Phase, if the iSCSI layer at the initiator
receives a Login Response from the target with a status class other
than 0 (Success) after the iSCSI layer at the initiator has invoked
the Allocate_Connection_Resources Operational Primitive, the iSCSI
layer MUST request the iSER layer to deallocate all connection
resources by invoking the Deallocate_Connection_Resources Operational
Primitive. The iSCSI layer MUST terminate the connection in this
case.
For negotiation failures during the Full Feature Phase, the error
handling is left to the iSCSI layer and no special handling at the
iSER layer is required.
10.2. Error Recovery
Error recovery requirements of iSCSI/iSER are the same as that of
Traditional iSCSI. All three ErrorRecoveryLevels as defined in
[RFC3720] are supported in iSCSI/iSER.
* For ErrorRecoveryLevel 0, session recovery is handled by iSCSI and
no special handling by the iSER layer is required.
* For ErrorRecoveryLevel 1, see Section 10.2.1 on PDU Recovery.
* For ErrorRecoveryLevel 2, see Section 10.2.2 on Connection
Recovery.
The iSCSI layer may invoke the Notice_Key_Values Operational
Primitive during connection setup to request that the iSER layer take
note of the value of the operational ErrorRecoveryLevel, as described
in Sections 5.1.1 and 5.1.2.
10.2.1. PDU Recovery
As described in Sections 10.1.4.2 and 10.1.4.3, digest and sequence
errors will not occur in the iSER-assisted mode. If the RCaP layer
detects an error, it will close the iSCSI/iSER connection, as
Ko, et al. Standards Track [Page 69]
RFC 5046 iSER Specification October 2007
described in Section 10.1.2. Therefore, PDU recovery is not useful
in the iSER-assisted mode.
The iSCSI layer at the initiator SHOULD disable iSCSI timeout-driven
PDU retransmissions.
10.2.2. Connection Recovery
The iSCSI layer at the initiator MAY reassign connection allegiance
for non-immediate commands that are still in progress and are
associated with the failed connection by using a Task Management
Function Request with the TASK REASSIGN function. See Section 7.3.3
for more details.
When the iSCSI layer at the initiator does a task reassignment for a
SCSI write command, it MUST qualify the Send_Control Operational
Primitive invocation with DataDescriptorOut, which defines the I/O
Buffer for both the non-immediate unsolicited data and the solicited
data. This allows the iSCSI layer at the target to use recovery R2Ts
to request data originally sent as unsolicited and solicited from the
initiator.
When the iSCSI layer at the target accepts a reassignment request for
a SCSI read command, it MUST request that the iSER layer process SCSI
Data-in for all unacknowledged data by invoking the Put_Data
Operational Primitive. See Section 7.3.5 on the handling of SCSI
Data-in.
When the iSCSI layer at the target accepts a reassignment request for
a SCSI write command, it MUST request that the iSER layer process a
recovery R2T for any non-immediate unsolicited data and any solicited
data sequences that have not been received by invoking the Get_Data
Operational Primitive. See Section 7.3.6 on the handling of Ready To
Transfer (R2T).
The iSCSI layer at the target MUST NOT issue recovery R2Ts on an
iSCSI/iSER connection for a task for which the connection allegiance
was never reassigned. The iSER layer at the target MAY reject such a
recovery R2T received via the Get_Data Operational Primitive
invocation from the iSCSI layer at the target, with an appropriate
error code.
The iSER layer at the target will process the requests invoked by the
Put_Data and Get_Data Operational Primitives for a reassigned task in
the same way as for the original commands.
Ko, et al. Standards Track [Page 70]
RFC 5046 iSER Specification October 2007
11. Security Considerations
When iSER is layered on top of an RCaP layer and provides the RDMA
extensions to the iSCSI protocol, the security considerations of iSER
are the same as that of the underlying RCaP layer. For iWARP, this
is described in [RDMAP] and [RDDPSEC].
Since the iSER-assisted iSCSI protocol is still functionally iSCSI
from a security considerations perspective, all of the iSCSI security
requirements as described in [RFC3720] and [RFC3723] apply. If the
IPsec [IPSEC] mechanism is used, then it MUST be established before
the connection transitions to the iSER-assisted mode. If iSER is
layered on top of a non-IP based RCaP layer, all the security
protocol mechanisms applicable to that RCaP layer are also applicable
to an iSCSI/iSER connection. If iSER is layered on top of a non-IP
protocol, the IPsec mechanism as specified in [RFC3720] MUST be
implemented at any point where the iSER protocol enters the IP
network (e.g., via gateways), and the non-IP protocol SHOULD
implement (optional to use) a packet-by packet security protocol
equal in strength to the IPsec mechanism specified by [RFC3720].
To minimize the potential for a denial-of-service attack, the iSCSI
layer MUST NOT request that the iSER layer allocate the connection
resources necessary to support RCaP until the iSCSI layer is
sufficiently far along in the iSCSI Login Phase that it is reasonably
certain that the peer side is not an attacker, as described in
Sections 5.1.1 and 5.1.2.
Note that the IPsec requirements for this document are based on the
version of IPsec specified in RFC 2401 [IPSEC] and related RFCs, as
profiled by RFC 3723 [RFC3723], despite the existence of a newer
version of IPsec specified in RFC 4301 [RFC4301] and related RFCs.
12. References
12.1. Normative References
[RFC3720] Satran, J., Meth, K., Sapuntzakis, C., Chadalapaka, M., and
E. Zeidner, "Internet Small Computer Systems Interface
(iSCSI)", RFC 3720, April 2004.
[RFC3723] Aboba, B., Tseng, J., Walker, J., Rangan, V., and F.
Travostino, "Securing Block Storage Protocols over IP", RFC
3723, April 2004.
[RDMAP] Recio, R., Culley, P., Garcia, D., Hilland, J., and B.
Metzler, "A Remote Direct Memory Access Protocol
Specification", RFC 5040, October 2007.
Ko, et al. Standards Track [Page 71]
RFC 5046 iSER Specification October 2007
[DDP] Shah, H., Pinkerton, J., Recio, R., and P. Culley, "Direct
Data Placement over Reliable Transports", RFC 5041, October
2007.
[IPSEC] Kent, S. and R. Atkinson, "Security Architecture for the
Internet Protocol", RFC 2401, November 1998.
[MPA] Culley, P., Elzur, U., Recio, R., Bailey, S., and J.
Carrier, "Marker PDU Aligned Framing for TCP
Specification", RFC 5044, October 2007.
[RDDPSEC] Pinkerton, J. and E. Deleganes, "Direct Data Placement
Protocol (DDP) / Remote Direct Memory Access Protocol
(RDMAP) Security", RFC 5042, October 2007.
[TCP] Postel, J., "Transmission Control Protocol", STD 7, RFC
793, September 1981.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
12.2. Informative References
[SAM2] T10/1157D, SCSI Architecture Model - 2 (SAM-2)
[DA] Chadalapaka, M., Hufferd, J., Satran, J., and H. Shah, "DA:
Datamover Architecture for the Internet Small Computer
System Interface (iSCSI)", RFC 5047, October 2007.
[IB] InfiniBand Architecture Specification Volume 1 Release 1.2,
October 2004
[IPoIB] Chu, J. and V. Kashyap, "Transmission of IP over InfiniBand
(IPoIB)", RFC 4391, April 2006.
[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, December 2005.
Ko, et al. Standards Track [Page 72]
RFC 5046 iSER Specification October 2007
Appendix A. iWARP Message Format for iSER
This section is for information only and is NOT part of the standard.
It simply depicts the iWARP Message format for the various iSER
Messages when the transport layer is TCP.
A.1. iWARP Message Format for iSER Hello Message
The following figure depicts an iSER Hello Message encapsulated in an
iWARP SendSE Message.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA Header | DDP Control | RDMA Control |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Queue Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Message Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Message Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0010b | Zeros | 0001b | 0001b | iSER-IRD |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| All Zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| All Zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA CRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6. SendSE Message Containing an iSER Hello Message
Ko, et al. Standards Track [Page 73]
RFC 5046 iSER Specification October 2007
A.2. iWARP Message Format for iSER HelloReply Message
The following figure depicts an iSER HelloReply Message encapsulated
in an iWARP SendSE Message. The Reject (REJ) flag is set to 0.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA Header | DDP Control | RDMA Control |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Queue Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Message Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Message Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0011b |Zeros|0| 0001b | 0001b | iSER-ORD |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| All Zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| All Zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA CRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 7. SendSE Message Containing an iSER HelloReply Message
Ko, et al. Standards Track [Page 74]
RFC 5046 iSER Specification October 2007
A.3. iWARP Message Format for SCSI Read Command PDU
The following figure depicts a SCSI Read Command PDU embedded in an
iSER Message encapsulated in an iWARP SendSE Message. For this
particular example, in the iSER header, the Write STag Valid flag is
set to zero, the Read STag Valid flag is set to one, the Write STag
field is set to all zeros, and the Read STag field contains a valid
Read STag.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA Header | DDP Control | RDMA Control |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Queue Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Message Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Message Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0001b |0|1| All zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| All Zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Read STag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCSI Read Command PDU |
// //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA CRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 8. SendSE Message Containing a SCSI Read Command PDU
Ko, et al. Standards Track [Page 75]
RFC 5046 iSER Specification October 2007
A.4. iWARP Message Format for SCSI Read Data
The following figure depicts an iWARP RDMA Write Message carrying
SCSI Read data in the payload:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA Header | DDP Control | RDMA Control |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Data Sink STag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Data Sink Tagged Offset |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCSI Read data |
// //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA CRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 9. RDMA Write Message Containing SCSI Read Data
Ko, et al. Standards Track [Page 76]
RFC 5046 iSER Specification October 2007
A.5. iWARP Message Format for SCSI Write Command PDU
The following figure depicts a SCSI Write Command PDU embedded in an
iSER Message encapsulated in an iWARP SendSE Message. For this
particular example, in the iSER header, the Write STag Valid flag is
set to one, the Read STag Valid flag is set to zero, the Write STag
field contains a valid Write STag, and the Read STag field is set to
all zeros since it is not used.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA Header | DDP Control | RDMA Control |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Queue Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Message Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Message Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0001b |1|0| All zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Write STag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| All Zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCSI Write Command PDU |
// //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA CRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 10. SendSE Message Containing a SCSI Write Command PDU
Ko, et al. Standards Track [Page 77]
RFC 5046 iSER Specification October 2007
A.6. iWARP Message Format for RDMA Read Request
An iSCSI R2T is transformed into an iWARP RDMA Read Request Message.
The following figure depicts an iWARP RDMA Read Request Message:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA Header | DDP Control | RDMA Control |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved (Not Used) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| DDP (RDMA Read Request) Queue Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| DDP (RDMA Read Request) Message Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| DDP (RDMA Read Request) Message Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Data Sink STag (SinkSTag) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ Data Sink Tagged Offset (SinkTO) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RDMA Read Message Size (RDMARDSZ) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Data Source STag (SrcSTag) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ Data Source Tagged Offset (SrcTO) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA CRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 11. RDMA Read Request Message
Ko, et al. Standards Track [Page 78]
RFC 5046 iSER Specification October 2007
A.7. iWARP Message Format for Solicited SCSI Write Data
The following figure depicts an iWARP RDMA Read Response Message
carrying the solicited SCSI Write data in the payload:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA Header | DDP Control | RDMA Control |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Data Sink STag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Data Sink Tagged Offset |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCSI Write Data |
// //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA CRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 12. RDMA Read Response Message Containing SCSI Write Data
Ko, et al. Standards Track [Page 79]
RFC 5046 iSER Specification October 2007
A.8. iWARP Message Format for SCSI Response PDU
The following figure depicts a SCSI Response PDU embedded in an iSER
Message encapsulated in an iWARP SendInvSE Message:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA Header | DDP Control | RDMA Control |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Invalidate STag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Queue Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Message Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| (Send) Message Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0001b |0|0| All Zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| All Zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| All Zeros |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCSI Response PDU |
// //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPA CRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 13. SendInvSE Message Containing SCSI Response PDU
Ko, et al. Standards Track [Page 80]
RFC 5046 iSER Specification October 2007
Appendix B. Architectural Discussion of iSER over InfiniBand
This section explains how an InfiniBand network (with Gateways) would
be structured. It is informational only and is intended to provide
insight on how iSER is used in an InfiniBand environment.
B.1. The Host Side of the iSCSI and iSER Connections in InfiniBand
Figure 14 defines the topologies in which iSCSI and iSER will be able
to operate on an InfiniBand Network.
+---------+ +---------+ +---------+ +---------+ +--- -----+
| Host | | Host | | Host | | Host | | Host |
| | | | | | | | | |
+---+-+---+ +---+-+---+ +---+-+---+ +---+-+---+ +---+-+---+
|HCA| |HCA| |HCA| |HCA| |HCA| |HCA| |HCA| |HCA| |HCA| |HCA|
+-v-+ +-v-+ +-v-+ +-v-+ +-v-+ +-v-+ +-v-+ +-v-+ +-v-+ +-v-+
|----+------|-----+-----|-----+-----|-----+-----|-----+---> To IB
IB| IB | IB | IB | IB | SubNet2 SWTCH
+-v-----------v-----------v-----------v-----------v---------+
| InfiniBand Switch for Subnet1 |
+---+-----+--------+-----+--------+-----+------------v------+
| TCA | | TCA | | TCA | |
+-----+ +-----+ +-----+ | IB
/ IB \ / IB \ / \ +--+--v--+--+
| iSER | | iSER | | IPoIB | | | TCA | |
| Gateway | | Gateway | | Gateway | | +-----+ |
| to | | to | | to | | Storage |
| iSCSI | | iSER | | IP | | Controller|
| TCP | | iWARP | |Ethernet | +-----+-----+
+---v-----| +---v-----| +----v----+
| EN | EN | EN
+--------------+---------------+----> to IP based storage
Ethernet links that carry iSCSI or iWARP
Figure 14. iSCSI and iSER on IB
In Figure 14, the Host systems are connected via the InfiniBand Host
Channel Adapters (HCAs) to the InfiniBand links. With the use of IB
switch(es), the InfiniBand links connect the HCA to InfiniBand Target
Channel Adapters (TCAs) located in gateways or Storage Controllers.
An iSER-capable IB-IP Gateway converts the iSER Messages encapsulated
in IB protocols to either standard iSCSI, or iSER Messages for iWARP.
An [IPoIB] Gateway converts the InfiniBand [IPoIB] protocol to IP
protocol, and in the iSCSI case, permits iSCSI to be operated on an
IB Network between the Hosts and the [IPoIB] Gateway.
Ko, et al. Standards Track [Page 81]
RFC 5046 iSER Specification October 2007
B.2. The Storage Side of the iSCSI and iSER Mixed Network Environment
Figure 15 shows a storage controller that has three different portal
groups: one supporting only iSCSI (TPG-4), one supporting iSER/iWARP
or iSCSI (TPG-2), and one supporting iSER/IB (TPG-1).
| | |
| | |
+--+--v--+----------+--v--+----------+--v--+--+
| | IB | |iWARP| | EN | |
| | | | TCP | | NIC | |
| |(TCA)| | RNIC| | | |
| +-----| +-----+ +-----+ |
| TPG-1 TPG-2 TPG-4 |
| 9.1.3.3 9.1.2.4 9.1.2.6 |
| |
| Storage Controller |
| |
+---------------------------------------------+
Figure 15. Storage Controller with TCP, iWARP, and IB Connections
The normal iSCSI portal group advertising processes (via the Service
Location Protocol (SLP), the Internet Storage Name Service (iSNS), or
SendTargets) are available to a Storage Controller.
B.3. Discovery Processes for an InfiniBand Host
An InfiniBand Host system can gather portal group IP addresses from
SLP, iSNS, or the SendTargets discovery processes by using TCP/IP via
[IPoIB]. After obtaining one or more remote portal IP addresses, the
Initiator uses the standard IP mechanisms to resolve the IP address
to a local outgoing interface and the destination hardware address
(Ethernet MAC or IB GID of the target or a gateway leading to the
target). If the resolved interface is an [IPoIB] network interface,
then the target portal can be reached through an InfiniBand fabric.
In this case, the Initiator can establish an iSCSI/TCP or iSCSI/iSER
session with the Target over that InfiniBand interface, using the
Hardware Address (InfiniBand GID) obtained through the standard
Address Resolution (ARP) processes.
If more than one IP address is obtained through the discovery
process, the Initiator should select a Target IP address that is on
the same IP subnet as the Initiator, if one exists. This will avoid
a potential overhead of going through a gateway when a direct path
exists.
Ko, et al. Standards Track [Page 82]
RFC 5046 iSER Specification October 2007
In addition, a user can configure manual static IP route entries if a
particular path to the target is preferred.
B.4. IBTA Connection Specifications
The InfiniBand Trade Association (IBTA) connection specifications are
outside the scope of this document, but it is expected that the IBTA
has or will define:
* The iSER ServiceID.
* A Means for permitting a Host to establish a connection with a
peer InfiniBand end-node, and to fall back to iSCSI/TCP over
[IPoIB] if that peer indicates iSER is not supported.
* A Means for permitting the Host to establish connections with IB
iSER connections on storage controllers or IB iSER connected
Gateways in preference to [IPoIB] connected Gateways/Bridges or
connections to Target Storage Controllers that also accept iSCSI
via [IPoIB].
* A Means for combining the IB ServiceID for iSER and the IP port
number such that the IB Host can use normal IB connection
processes, yet ensure that the iSER target peer can actually
connect to the required IP port number.
Acknowledgments
This protocol was developed by a design team that, in addition to the
authors, included Dwight Barron (HP), John Carrier (formerly from
Adaptec), Ted Compton (EMC), Paul R. Culley (HP), Yaron Haviv
(Voltaire), Jeff Hilland (HP), Mike Krause (HP), Alex Nezhinsky
(Voltaire), Jim Pinkerton (Microsoft), Renato J. Recio (IBM), Julian
Satran (IBM), Tom Talpey (Network Appliance), and Jim Wendt (HP).
Special thanks to David Black (EMC) for his extensive review
comments.
Ko, et al. Standards Track [Page 83]
RFC 5046 iSER Specification October 2007
Author's Address
Mallikarjun Chadalapaka
Hewlett-Packard Company
8000 Foothills Blvd.
Roseville, CA 95747-5668, USA
Phone: +1-916-785-5621
EMail: cbm@rose.hp.com
Uri Elzur
Broadcom Corporation
5300 California Avenue
Irvine, CA 92617, USA
Phone: +1-949-926-6432
EMail: Uri@Broadcom.com
John Hufferd
Brocade Communications Systems, Inc.
1745 Technology Drive
San Jose, CA 95110, USA
Phone: +1-408-333-5244
EMail: jhufferd@brocade.com
Mike Ko
IBM Corp.
650 Harry Rd.
San Jose, CA 95120, USA
Phone: +1-408-927-2085
EMail: mako@us.ibm.com
Hemal Shah
Broadcom Corporation
5300 California Avenue
Irvine, CA 92617, USA
Phone: +1-949-926-6941
EMail: hemal@broadcom.com
Patricia Thaler
Broadcom Corporation
5300 California Avenue
Irvine, CA 92617, USA
Phone: +1-916-570-2707
EMail: pthaler@broadcom.com
Ko, et al. Standards Track [Page 84]
RFC 5046 iSER Specification October 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Ko, et al. Standards Track [Page 85]