💾 Archived View for radia.bortzmeyer.org › rfc-mirror › rfc5332.txt captured on 2024-07-09 at 03:50:18.

View Raw

More Information

⬅️ Previous capture (2023-06-14)

-=-=-=-=-=-=-







Network Working Group                                          T. Eckert
Request for Comments: 5332                                 E. Rosen, Ed.
Category: Standards Track                            Cisco Systems, Inc.
Updates: 3032, 4023                                          R. Aggarwal
                                                              Y. Rekhter
                                                  Juniper Networks, Inc.
                                                             August 2008


                     MPLS Multicast Encapsulations

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Abstract

   RFC 3032 established two data link layer codepoints for MPLS, used to
   distinguish whether the data link layer frame is carrying an MPLS
   unicast or an MPLS multicast packet.  However, this usage was never
   deployed.  This specification updates RFC 3032 by redefining the
   meaning of these two codepoints.  Both codepoints can now be used to
   carry multicast packets.  The second codepoint (formerly the
   "multicast codepoint") is now to be used only on multiaccess media,
   and it is to mean "the top label of the following label stack is an
   upstream-assigned label".

   RFC 3032 does not specify the destination address to be placed in the
   "MAC DA" (Medium Access Layer Destination Address) field of an
   ethernet frame that carries an MPLS multicast packet.  This document
   provides that specification.

   This document updates RFC 3032 and RFC 4023.














Eckert, et al.              Standards Track                     [Page 1]

RFC 5332             MPLS Multicast Encapsulations           August 2008


Table of Contents

   1. Introduction ....................................................2
   2. Specification of Requirements ...................................3
   3. Upstream-Assigned vs. Downstream-Assigned .......................3
   4. Ethernet Codepoints .............................................6
   5. PPP Protocol Field ..............................................6
   6. GRE Protocol Type ...............................................6
   7. IP Protocol Number ..............................................7
   8. Ethernet MAC DA for Multicast MPLS ..............................7
   9. IANA Considerations .............................................8
   10. Security Considerations ........................................8
   11. Normative References ...........................................9

1.  Introduction

   RFC 3031 [RFC3031] defines the "Next Hop Label Forwarding Entry"
   (NHLFE).  The NHLFE for a particular label maps the label into a next
   hop (among other things).  When an MPLS packet is received, its top
   label is mapped to an NHLFE, and the packet is sent to the next hop
   specified by the NHLFE.

   We define a particular MPLS label to be a "multicast label" in a
   particular context if the NHLFE to which it is mapped, in that
   context, specifies a set of next hops, with the semantics that the
   packet is to be replicated and a copy of the packet sent to each of
   the specified next hops.  Note that this definition accommodates the
   case where the set of next hops contains a single member.  What makes
   a label a multicast label in a particular context is the semantics
   attached to the set, i.e., the intention to replicate the packet and
   transmit to all members of the set if the set has more than one
   member.

   RFC 3032 [RFC3032] established two data link layer codepoints for
   MPLS: one to indicate that the data link layer frame is carrying an
   MPLS unicast packet, and the other to indicate that the data link
   layer frame is carrying an MPLS multicast packet.  The term
   "multicast packet" is not precisely defined in RFC 3032, though one
   may presume that the "multicast" codepoint is intended to identify
   the packet's top label as a multicast label.  However, the multicast
   codepoint has never been deployed, and further development of the
   procedures for MPLS multicast have shown that, while there is a need
   for two codepoints, the use of the two codepoints is not properly
   captured by RFC 3032.







Eckert, et al.              Standards Track                     [Page 2]

RFC 5332             MPLS Multicast Encapsulations           August 2008


   In particular, there is no need for the codepoint to indicate whether
   the top MPLS label is a multicast label.  When the receiver of an
   MPLS packet looks up the top label, the NHLFE will specify whether or
   not the label is a multicast label.

   This document updates RFC 3032 and RFC 4023 by re-specifying the use
   of the codepoints.  The old use of the "multicast codepoint", as
   specified in those two RFCs, is hereby deprecated.

   Note that an implementation that does MPLS multicast according to RFC
   3032 and/or 4023 will be unable to interoperate with implementations
   that do MPLS multicast according to this document.  There may be some
   deployed platforms that support the deprecated use of the codepoints,
   but those platforms do not support the control plane mechanisms to
   support MPLS multicast.  The absence of the control plane will
   prevent a system that implements the deprecated use of codepoints
   from attempting to interoperate with a system that uses the
   codepoints as specified herein.  (If an MPLS multicast control plane
   were to be implemented on a platform that only supports the
   deprecated codepoint, interoperability problems such as black holes
   and/or misrouting would arise.  This does not seem like a potential
   problem in practice.)

   While RFC 3032 allows an MPLS packet to be carried in an ethernet
   multicast frame, it fails to specify how the Medium Access Layer
   Destination Address (MAC DA) field is to be set in that case.  This
   document provides that specification.

2.  Specification of Requirements

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

3.  Upstream-Assigned vs. Downstream-Assigned

   Suppose a labeled packet P is sent from Label Switching Router (LSR)
   R1 to LSR R2, where R1 puts label L on the packet's label stack, and
   R2 has to look up label L in order to determine the corresponding
   Forwarding Equivalence Class (FEC), call it F.

   If the binding between L and F was made by R2 and advertised to R1,
   then the label binding is known as "downstream-assigned".  RFC 3031
   only discusses downstream-assigned label bindings.

   If the binding between L and F was made by R1 and advertised to R2,
   then the label binding is known as "upstream-assigned".




Eckert, et al.              Standards Track                     [Page 3]

RFC 5332             MPLS Multicast Encapsulations           August 2008


   If the binding between L and F was made by a third party, say R3, and
   then advertised to both R1 and R2, we also refer to the label binding
   as "upstream-assigned".

   Upstream-assigned labels are not required to come from the same
   "label space" as downstream-assigned labels.  See Section 3.14 of
   [RFC3031] and especially [RFC5331] for a discussion of the notion of
   "label space".  The procedures for properly interpreting an upstream-
   assigned label are given in [RFC5331].

   If Ru and Rd are LSP adjacencies, then they transmit an MPLS packet
   to each other through one of the following mechanisms:

      1. by putting the MPLS packet in a data link layer frame and
         transmitting the frame,

      2. by transmitting the MPLS packet through an MPLS tunnel, i.e.,
         by pushing an additional label (or labels) onto the label
         stack, and then invoking mechanism 1, or

      3. by transmitting the MPLS packet through an IP-based tunnel
         (e.g., via RFC 4023 [RFC4023]), and then invoking mechanisms 1
         and/or 2.

   In short, an MPLS packet is transmitted through a data link, through
   an MPLS tunnel, or through an IP tunnel.  In any of those cases, when
   the packet emerges through the tunnel, the downstream LSR must know
   whether the label that now appears at the top of the label stack has
   an upstream-assigned label binding or a downstream-assigned label
   binding.  For convenience, we will speak of a label with an
   upstream-assigned label binding as an "upstream-assigned label".

   Under certain conditions, specified below, multicast labels MAY be
   upstream-assigned.  The ability to use upstream-assigned labels is an
   OPTIONAL feature.  Upstream-assigned labels MUST NOT be used unless
   it is known that the downstream LSR supports them.  How this is known
   is outside the scope of this document.

   This document makes no changes to the procedures regarding unicast
   labels.

   We discuss three different types of data link or tunnel:

      - Point-to-Point.  A point-to-point data link or tunnel associates
        two systems, such that transmissions on that link or tunnel made
        by one are received by the other, and only by the other.





Eckert, et al.              Standards Track                     [Page 4]

RFC 5332             MPLS Multicast Encapsulations           August 2008


        For a given direction of a given point-to-point data link or
        tunnel, the following MUST be the case:  either every MPLS
        packet will carry an upstream-assigned label, or else every MPLS
        packet will carry a downstream-assigned label.  The procedures
        for determining whether upstream-assigned or downstream-assigned
        labels are being used are outside the scope of this
        specification.  However, in the absence of any other
        information, the use of downstream-assigned labels MUST be
        presumed by default.

      - Point-to-Multipoint.  A point-to-multipoint link or tunnel
        associates n systems, such that only one of them can transmit
        onto the link or tunnel, and the transmissions may be received
        by the other n-1 systems.

        The top labels (before applying the data link or tunnel
        encapsulation) of all MPLS packets that are transmitted on a
        particular point-to-multipoint data link or tunnel MUST be of
        the same type; either all upstream-assigned or all downstream-
        assigned.  This means that all the receivers on the MPLS or IP
        tunnel must know a priori whether upstream-assigned or
        downstream-assigned labels are being used in the tunnel.  How
        this is known is outside the scope of this document.

      - Multipoint-to-Multipoint.  A multipoint-to-multipoint link or
        tunnel associates n systems, such that any of them can transmit
        on the link or tunnel, and the transmissions may be received by
        the other n-1 systems.

        If MPLS packets are transmitted on a particular multipoint-to-
        multipoint link or tunnel, one of the following scenarios
        applies:

         1. It is known (by methods outside the scope of this document)
            that the top label of every MPLS packet on the link or
            tunnel is downstream-assigned.

         2. It is known (by methods outside the scope of this document)
            that the top label of every MPLS packet on the link or
            tunnel is upstream-assigned.

         3. Some MPLS packets on the link may have upstream-assigned top
            labels while some may have downstream-assigned top labels.








Eckert, et al.              Standards Track                     [Page 5]

RFC 5332             MPLS Multicast Encapsulations           August 2008


      If (and only if) the third scenario applies, the data link or
      tunnel encapsulation MUST provide a codepoint that specifies
      whether the top label of the encapsulated MPLS packet is
      upstream-assigned or downstream-assigned.  If a particular type of
      data link or tunnel does not provide such a codepoint, then the
      third scenario MUST NOT be used.

   The remainder of this document specifies procedures for setting the
   data link layer codepoints and address fields.

4.  Ethernet Codepoints

   Ethernet is an example of a multipoint-to-multipoint data link.

   Ethertype 0x8847 is used whenever a unicast ethernet frame carries an
   MPLS packet.

   Ethertype 0x8847 is also used whenever a multicast ethernet frame
   carries an MPLS packet, EXCEPT for the case where the top label of
   the MPLS packet has been upstream-assigned.

   Ethertype 0x8848, formerly known as the "MPLS multicast codepoint",
   is to be used only when an MPLS packet whose top label is upstream-
   assigned is carried in a multicast ethernet frame.

5.  PPP Protocol Field

   PPP is an example of a point-to-point data link.  When a PPP frame is
   carrying an MPLS packet, the PPP Protocol field is always set to
   0x0281.

6.  GRE Protocol Type

   RFC 4023 is modified as described below.

   If the IP destination address of the Generic Routing Encapsulation
   (GRE) is a unicast IP address, then the ethertype value 0x8847 MUST
   be used in all cases for the MPLS-in-GRE encapsulation.

   If the IP destination address of the GRE encapsulation is a multicast
   IP address, then:

      - the ethertype value 0x8847 MUST be used when the top label of
        the encapsulated MPLS packet is downstream-assigned,

      - the ethertype value 0x8848 MUST be used when the top label of
        the encapsulated MPLS packet is upstream-assigned.




Eckert, et al.              Standards Track                     [Page 6]

RFC 5332             MPLS Multicast Encapsulations           August 2008


   Through procedures that are outside the scope of this specification,
   it may be known that if the destination address of a GRE packet is a
   multicast IP address, then the top label of the GRE payload is
   upstream-assigned.  In such a case, the occurrence of the 8847
   codepoint in a GRE packet with a multicast destination IP address
   MUST be considered an error, and the packet MUST be discarded.

7.  IP Protocol Number

   RFC 4023 is modified as follows: the IPv4 Protocol Number field or
   the IPv6 Next Header field is always set to 137, whether or not the
   encapsulated MPLS packet is an MPLS multicast packet.

   If the IP destination address of the IP encapsulation is an IP
   multicast address, the IP tunnel may be considered to be a point-to-
   multipoint tunnel or a multipoint-to-multipoint tunnel.  In either
   case, either all encapsulated MPLS packets in the particular tunnel
   have a downstream-assigned label at the top of the stack, or all
   encapsulated MPLS packets in that tunnel have an upstream-assigned
   label at the top of the stack.  The means by which this is determined
   for a particular tunnel is outside the scope of this specification.

8.  Ethernet MAC DA for Multicast MPLS

   When an LSR transmits a multicast MPLS packet in a multicast ethernet
   frame, it MUST set the MAC Destination Address to the value
   01-00-5e-8v-wx-yz, where vwxyz is a 20-bit (five-nibble) value set as
   follows:

      1. vwxyz MAY be set to 0,

      2. vwxyz MAY be set to the value of one of the MPLS labels on the
         packet's label stack.

   Which of these procedures is the default procedure in any particular
   LSR is implementation-dependent.  However, LSRs using the two
   different procedures MUST interoperate.  That is, an LSR MUST NOT
   filter packets for which vwxyz has been set to zero, and it MUST NOT
   indiscriminately filter all packets for which vwxyz has not been set
   to zero.

   If an LSR follows the procedure of setting vwxyz to the value of one
   of the MPLS labels on the packet's label stack, and if that label
   stack contains two or more labels, then by default, vwxyz MUST be set
   to the value of the second MPLS label on the packet's label stack.
   By "the second label", we mean the label that is in the label stack
   entry that immediately follows the topmost label stack entry.  The
   LSR MAY, if configured to do so, allow a label other than the second



Eckert, et al.              Standards Track                     [Page 7]

RFC 5332             MPLS Multicast Encapsulations           August 2008


   to be used for this purpose.  If the MPLS packet has only one label,
   the value of that label will be used instead of the value of the
   (non-existent) second label.

   It is expected that the LSR will follow the procedures of [RFC5331],
   pushing on two labels, with the topmost label being a "context label"
   that is the same for all MPLS packets being transmitted by the LSR
   onto the ethernet, but with the second label being different for
   different LSPs.  Thus, if the MAC DA value is a function of the
   second label, more of the LSP-specific information about the packet
   appears in the MAC DA field.  This can be used to filter multicast
   packets with "unexpected" non-zero values of vwxyz.  Further
   discussion of such filtering or its uses is outside the scope of this
   document.

   The use of ethernet and/or IP broadcast addresses (as distinguished
   from multicast addresses) does not fall within the scope of this
   specification.

9.  IANA Considerations

   IANA already owns the set of ethernet multicast addresses in the
   range 01-00-5e-00-00-00 to 01-00-5e-ff-ff-ff.  Addresses in the range
   01-00-5e-00-00-00 to 01-00-5e-7f-ff-ff are already reserved for use
   when an ethernet multicast frame carries an IP multicast packet.

   IANA has reserved ethernet addresses in the range 01-00-5e-80-00-00
   to 01-00-5e-8f-ff-ff for use when an ethernet multicast frame carries
   an MPLS multicast packet.  Addresses in this range are valid when
   used with ethertype 8847 or 8848.

   As this document modifies the usage of ethertypes 8847 and 8848, IANA
   has changed the description of these ethertypes as follows.
   Ethertype 8847 is defined as "MPLS", as defined in RFC 3032 and in
   this document.  Ethertype 8848 is defined as "MPLS with upstream-
   assigned label", as defined in this document.

10.  Security Considerations

   The security considerations of RFC 3032 and RFC 4023 apply.

   Malicious changing of the codepoint may result in loss or misrouting
   of packets.  However, altering the codepoint without also altering
   the label does not result in a predictable effect.

   Malicious alteration of the MAC DA on an ethernet can result in
   packets being received by a third party, rather than by the intended
   recipient.



Eckert, et al.              Standards Track                     [Page 8]

RFC 5332             MPLS Multicast Encapsulations           August 2008


11.  Normative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3031] Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
             Label Switching Architecture", RFC 3031, January 2001.

   [RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
             Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
             Encoding", RFC 3032, January 2001.

   [RFC4023] Worster, T., Rekhter, Y., and E. Rosen, Ed., "Encapsulating
             MPLS in IP or Generic Routing Encapsulation (GRE)", RFC
             4023, March 2005.

   [RFC5331] Aggarwal, R., Rekhter, Y., and E. Rosen, "MPLS Upstream
             Label Assignment and Context-Specific Label Space",  RFC
             5331, August 2008.
































Eckert, et al.              Standards Track                     [Page 9]

RFC 5332             MPLS Multicast Encapsulations           August 2008


Authors' Addresses

   Toerless Eckert
   Cisco Systems, Inc.
   170 Tasman Drive
   San Jose, CA, 95134

   EMail: eckert@cisco.com


   Eric C. Rosen
   Cisco Systems, Inc.
   1414 Massachusetts Avenue
   Boxborough, MA 01719

   EMail: erosen@cisco.com


   Rahul Aggarwal
   Juniper Networks
   1194 North Mathilda Ave.
   Sunnyvale, CA 94089

   EMail: rahul@juniper.net


   Yakov Rekhter
   Juniper Networks
   1194 North Mathilda Ave.
   Sunnyvale, CA 94089

   EMail: yakov@juniper.net



















Eckert, et al.              Standards Track                    [Page 10]

RFC 5332             MPLS Multicast Encapsulations           August 2008


Full Copyright Statement

   Copyright (C) The IETF Trust (2008).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.












Eckert, et al.              Standards Track                    [Page 11]