💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc4215.txt captured on 2024-06-16 at 17:32:06.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group J. Wiljakka, Ed.
Request for Comments: 4215 Nokia
Category: Informational October 2005
Analysis on IPv6 Transition in
Third Generation Partnership Project (3GPP) Networks
Status of This Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2005).
Abstract
This document analyzes the transition to IPv6 in Third Generation
Partnership Project (3GPP) packet networks. These networks are based
on General Packet Radio Service (GPRS) technology, and the radio
network architecture is based on Global System for Mobile
Communications (GSM) or Universal Mobile Telecommunications System
(UMTS)/Wideband Code Division Multiple Access (WCDMA) technology.
The focus is on analyzing different transition scenarios and
applicable transition mechanisms and finding solutions for those
transition scenarios. In these scenarios, the User Equipment (UE)
connects to other nodes, e.g., in the Internet, and IPv6/IPv4
transition mechanisms are needed.
Table of Contents
1. Introduction ....................................................2
1.1. Scope of This Document .....................................3
1.2. Abbreviations ..............................................3
1.3. Terminology ................................................5
2. Transition Mechanisms and DNS Guidelines ........................5
2.1. Dual Stack .................................................5
2.2. Tunneling ..................................................6
2.3. Protocol Translators .......................................6
2.4. DNS Guidelines for IPv4/IPv6 Transition ....................6
3. GPRS Transition Scenarios .......................................7
3.1. Dual Stack UE Connecting to IPv4 and IPv6 Nodes ............7
3.2. IPv6 UE Connecting to an IPv6 Node through an IPv4
Network ....................................................8
Wiljakka Informational [Page 1]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
3.2.1. Tunneling Inside the 3GPP Operator's Network ........9
3.2.2. Tunneling Outside the 3GPP Operator's Network ......10
3.3. IPv4 UE Connecting to an IPv4 Node through an IPv6
Network ...................................................10
3.4. IPv6 UE Connecting to an IPv4 Node ........................11
3.5. IPv4 UE Connecting to an IPv6 Node ........................12
4. IMS Transition Scenarios .......................................12
4.1. UE Connecting to a Node in an IPv4 Network through IMS ....12
4.2. Two IPv6 IMS Connected via an IPv4 Network ................15
5. About 3GPP UE IPv4/IPv6 Configuration ..........................15
6. Summary and Recommendations ....................................16
7. Security Considerations ........................................17
8. References .....................................................17
8.1. Normative References ......................................17
8.2. Informative References ....................................18
9. Contributors ...................................................20
10. Authors and Acknowledgements ..................................20
1. Introduction
This document describes and analyzes the process of transition to
IPv6 in Third Generation Partnership Project (3GPP) General Packet
Radio Service (GPRS) packet networks [3GPP-23.060], in which the
radio network architecture is based on Global System for Mobile
Communications (GSM) or Universal Mobile Telecommunications System
(UMTS)/Wideband Code Division Multiple Access (WCDMA) technology.
This document analyzes the transition scenarios that may come up in
the deployment phase of IPv6 in 3GPP packet data networks.
The 3GPP network architecture is described in [RFC3314], and relevant
transition scenarios are documented in [RFC3574]. The reader of this
specification should be familiar with the material presented in these
documents.
The scenarios analyzed in this document are divided into two
categories: general-purpose packet service scenarios, referred to as
GPRS scenarios in this document, and IP Multimedia Subsystem (IMS)
scenarios, which include Session Initiation Protocol (SIP)
considerations. For more information about IMS, see [3GPP-23.228],
[3GPP-24.228], and [3GPP-24.229].
GPRS scenarios are the following:
- Dual Stack User Equipment (UE) connecting to IPv4 and IPv6 nodes
- IPv6 UE connecting to an IPv6 node through an IPv4 network
- IPv4 UE connecting to an IPv4 node through an IPv6 network
- IPv6 UE connecting to an IPv4 node
Wiljakka Informational [Page 2]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
- IPv4 UE connecting to an IPv6 node
IMS scenarios are the following:
- UE connecting to a node in an IPv4 network through IMS
- Two IPv6 IMS connected via an IPv4 network
The focus is on analyzing different transition scenarios and
applicable transition mechanisms and finding solutions for those
transition scenarios. In the scenarios, the User Equipment (UE)
connects to nodes in other networks, e.g., in the Internet, and
IPv6/IPv4 transition mechanisms are needed.
1.1. Scope of This Document
The scope of this document is to analyze the possible transition
scenarios in the 3GPP-defined GPRS network in which a UE connects to,
or is contacted from, another node on the Internet. This document
covers scenarios with and without the use of the SIP-based IP
Multimedia Core Network Subsystem (IMS). This document does not
focus on radio-interface-specific issues; both 3GPP Second and Third
Generation radio network architectures (GSM, Enhanced Data rates for
GSM Evolution (EDGE) and UMTS/WCDMA) will be covered by this
analysis.
The 3GPP2 architecture is similar to 3GPP in many ways, but differs
in enough details that this document does not include these
variations in its analysis.
The transition mechanisms specified by the IETF Ngtrans and v6ops
Working Groups shall be used. This memo shall not specify any new
transition mechanisms, but only documents the need for new ones (if
appropriate).
1.2. Abbreviations
2G Second Generation Mobile Telecommunications, e.g., GSM
and GPRS technologies
3G Third Generation Mobile Telecommunications, e.g., UMTS
technology
3GPP Third Generation Partnership Project
ALG Application Level Gateway
APN Access Point Name. The APN is a logical name referring
to a GGSN and an external network.
Wiljakka Informational [Page 3]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
B2BUA Back-to-Back User Agent
CSCF Call Session Control Function (in 3GPP Release 5 IMS)
DNS Domain Name System
EDGE Enhanced Data rates for GSM Evolution
GGSN Gateway GPRS Support Node (default router for 3GPP User
Equipment)
GPRS General Packet Radio Service
GSM Global System for Mobile Communications
HLR Home Location Register
IMS IP Multimedia (Core Network) Subsystem, 3GPP Release 5
IPv6-only part of the network
ISP Internet Service Provider
NAT Network Address Translation
NAPT-PT Network Address Port Translation - Protocol Translation
NAT-PT Network Address Translation - Protocol Translation
PCO-IE Protocol Configuration Options Information Element
PDP Packet Data Protocol
PPP Point-to-Point Protocol
SDP Session Description Protocol
SGSN Serving GPRS Support Node
SIIT Stateless IP/ICMP Translation Algorithm
SIP Session Initiation Protocol
UE User Equipment, e.g., a UMTS mobile handset
UMTS Universal Mobile Telecommunications System
WCDMA Wideband Code Division Multiple Access
Wiljakka Informational [Page 4]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
1.3. Terminology
Some terms used in 3GPP transition scenarios and analysis documents
are briefly defined here.
Dual Stack UE Dual Stack UE is a 3GPP mobile handset having both
IPv4 and IPv6 stacks. It is capable of activating
both IPv4 and IPv6 Packet Data Protocol (PDP)
contexts. Dual stack UE may be capable of tunneling.
IPv6 UE IPv6 UE is an IPv6-only 3GPP mobile handset. It is
only capable of activating IPv6 PDP contexts.
IPv4 UE IPv4 UE is an IPv4-only 3GPP mobile handset. It is
only capable of activating IPv4 PDP contexts.
IPv4 node IPv4 node is here defined to be the IPv4-capable node
the UE is communicating with. The IPv4 node can be,
e.g., an application server or another UE.
IPv6 node IPv6 node is here defined to be the IPv6-capable node
the UE is communicating with. The IPv6 node can be,
e.g., an application server or another UE.
PDP Context Packet Data Protocol (PDP) Context is a connection
between the UE and the GGSN, over which the packets
are transferred. There are currently three PDP types:
IPv4, IPv6, and PPP.
2. Transition Mechanisms and DNS Guidelines
This section briefly introduces these IETF IPv4/IPv6 transition
mechanisms:
- dual IPv4/IPv6 stack [RFC4213]
- tunneling [RFC4213]
- protocol translators [RFC2766], [RFC2765]
In addition, DNS recommendations are given. The applicability of
different transition mechanisms to 3GPP networks is discussed in
sections 3 and 4.
2.1. Dual Stack
The dual IPv4/IPv6 stack is specified in [RFC4213]. If we consider
the 3GPP GPRS core network, dual stack implementation in the Gateway
GPRS Support Node (GGSN) enables support for IPv4 and IPv6 PDP
contexts. UEs with dual stack and public (global) IP addresses can
Wiljakka Informational [Page 5]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
typically access both IPv4 and IPv6 services without additional
translators in the network. However, it is good to remember that
private IPv4 addresses and NATs [RFC2663] have been used and will be
used in mobile networks. Public/global IP addresses are also needed
for peer-to-peer services: the node needs a public/global IP address
that is visible to other nodes.
2.2. Tunneling
Tunneling is a transition mechanism that requires dual IPv4/IPv6
stack functionality in the encapsulating and decapsulating nodes.
Basic tunneling alternatives are IPv6-in-IPv4 and IPv4-in-IPv6.
Tunneling can be static or dynamic. Static (configured) tunnels are
fixed IPv6 links over IPv4, and they are specified in [RFC4213].
Dynamic (automatic) tunnels are virtual IPv6 links over IPv4 where
the tunnel endpoints are not configured, i.e., the links are created
dynamically.
2.3. Protocol Translators
A translator can be defined as an intermediate component between a
native IPv4 node and a native IPv6 node to enable direct
communication between them without requiring any modifications to the
end nodes.
Header conversion is a translation mechanism. In header conversion,
IPv6 packet headers are converted to IPv4 packet headers, or vice
versa, and checksums are adjusted or recalculated if necessary.
NAT-PT (Network Address Translation/Protocol Translation) [RFC2766]
using Stateless IP/ICMP Translation [RFC2765] is an example of such a
mechanism.
Translators may be needed in some cases when the communicating nodes
do not share the same IP version; in others, it may be possible to
avoid such communication altogether. Translation can take place at
the network layer (using NAT-like techniques), the transport layer
(using a TCP/UDP proxy), or the application layer (using application
relays).
2.4. DNS Guidelines for IPv4/IPv6 Transition
To avoid the DNS name space from fragmenting into parts where some
parts of DNS are visible only using IPv4 (or IPv6) transport, the
recommendation (as of this writing) is to always keep at least one
authoritative server IPv4-enabled, and to ensure that recursive DNS
servers support IPv4. See DNS IPv6 transport guidelines [RFC3901]
for more information.
Wiljakka Informational [Page 6]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
3. GPRS Transition Scenarios
This section discusses the scenarios that might occur when a GPRS UE
contacts services or other nodes, e.g., a web server in the Internet.
The following scenarios described by [RFC3574] are analyzed here. In
all of the scenarios, the UE is part of a network where there is at
least one router of the same IP version, i.e., the GGSN, and the UE
is connecting to a node in a different network.
1) Dual Stack UE connecting to IPv4 and IPv6 nodes
2) IPv6 UE connecting to an IPv6 node through an IPv4 network
3) IPv4 UE connecting to an IPv4 node through an IPv6 network
4) IPv6 UE connecting to an IPv4 node
5) IPv4 UE connecting to an IPv6 node
3.1. Dual Stack UE Connecting to IPv4 and IPv6 Nodes
In this scenario, the dual stack UE is capable of communicating with
both IPv4 and IPv6 nodes.
It is recommended to activate an IPv6 PDP context when communicating
with an IPv6 peer node and an IPv4 PDP context when communicating
with an IPv4 peer node. If the 3GPP network supports both IPv4 and
IPv6 PDP contexts, the UE activates the appropriate PDP context
depending on the type of application it has started or depending on
the address of the peer host it needs to communicate with. The
authors leave the PDP context activation policy to be decided by UE
implementers, application developers, and operators. One discussed
possibility is to activate both IPv4 and IPv6 types of PDP contexts
in advance, because activation of a PDP context usually takes some
time. However, that probably is not good usage of network resources.
Generally speaking, IPv6 PDP contexts should be preferred even if
that meant IPv6-in-IPv4 tunneling would be needed in the network (see
Section 3.2 for more details). Note that this is transparent to the
UE.
Although the UE is dual stack, the UE may find itself attached to a
3GPP network in which the Serving GPRS Support Node (SGSN), the GGSN,
and the Home Location Register (HLR) support IPv4 PDP contexts, but
do not support IPv6 PDP contexts. This may happen in early phases of
IPv6 deployment, or because the UE has "roamed" from a 3GPP network
that supports IPv6 to one that does not. If the 3GPP network does
not support IPv6 PDP contexts, and an application on the UE needs to
Wiljakka Informational [Page 7]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
communicate with an IPv6(-only) node, the UE may activate an IPv4 PDP
context and encapsulate IPv6 packets in IPv4 packets using a
tunneling mechanism.
The tunneling mechanism may require public IPv4 addresses, but there
are tunneling mechanisms and deployment scenarios in which private
IPv4 addresses may be used, for instance, if the tunnel endpoints are
in the same private domain, or the tunneling mechanism works through
IPv4 NAT.
One deployment scenario uses a laptop computer and a 3GPP UE as a
modem. IPv6 packets are encapsulated in IPv4 packets in the laptop
computer and an IPv4 PDP context is activated. The tunneling
mechanism depends on the laptop computer's support of tunneling
mechanisms. Another deployment scenario is performing IPv6-in-IPv4
tunneling in the UE itself and activating an IPv4 PDP context.
Closer details for an applicable tunneling mechanism are not analyzed
in this document. However, a simple host-to-router (automatic)
tunneling mechanism can be a good fit. There is not yet consensus on
the right approach, and proposed mechanisms so far include [ISATAP]
and [STEP]. Especially ISATAP has had some support in the working
group. Goals for 3GPP zero-configuration tunneling are documented in
[zeroconf].
This document strongly recommends that the 3GPP operators deploy
basic IPv6 support in their GPRS networks. That makes it possible to
lessen the transition effects in the UEs.
As a general guideline, IPv6 communication is preferred to IPv4
communication going through IPv4 NATs to the same dual stack peer
node.
Public IPv4 addresses are often a scarce resource for the operator,
and usually it is not possible for a UE to have a public IPv4 address
(continuously) allocated for its use. Use of private IPv4 addresses
means use of NATs when communicating with a peer node outside the
operator's network. In large networks, NAT systems can become very
complex, expensive, and difficult to maintain.
3.2. IPv6 UE Connecting to an IPv6 Node through an IPv4 Network
The best solution for this scenario is obtained with tunneling; i.e.,
IPv6-in-IPv4 tunneling is a requirement. An IPv6 PDP context is
activated between the UE and the GGSN. Tunneling is handled in the
network, because IPv6 UE does not have the dual stack functionality
needed for tunneling. The encapsulating node can be the GGSN, the
edge router between the border of the operator's IPv6 network and the
Wiljakka Informational [Page 8]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
public Internet, or any other dual stack node within the operator's
IP network. The encapsulation (uplink) and decapsulation (downlink)
can be handled by the same network element. Typically, the tunneling
handled by the network elements is transparent to the UEs and IP
traffic looks like native IPv6 traffic to them. For the applications
and transport protocols, tunneling enables end-to-end IPv6
connectivity.
IPv6-in-IPv4 tunnels between IPv6 islands can be either static or
dynamic. The selection of the type of tunneling mechanism is a
policy decision for the operator/ISP deployment scenario, and only
generic recommendations can be given in this document.
The following subsections are focused on the usage of different
tunneling mechanisms when the peer node is in the operator's network
or outside the operator's network. The authors note that where the
actual 3GPP network ends and which parts of the network belong to the
ISP(s) also depend on the deployment scenario. The authors are not
commenting on how many ISP functions the 3GPP operator should
perform. However, many 3GPP operators are ISPs of some sort
themselves. ISP networks' transition to IPv6 is analyzed in
[RFC4029].
3.2.1. Tunneling Inside the 3GPP Operator's Network
GPRS operators today have typically deployed IPv4 backbone networks.
IPv6 backbones can be considered quite rare in the first phases of
the transition.
In initial IPv6 deployment, where a small number of IPv6-in-IPv4
tunnels are required to connect the IPv6 islands over the 3GPP
operator's IPv4 network, manually configured tunnels can be used. In
a 3GPP network, one IPv6 island can contain the GGSN while another
island can contain the operator's IPv6 application servers. However,
manually configured tunnels can be an administrative burden when the
number of islands and therefore tunnels rises. In that case,
upgrading parts of the backbone to dual stack may be the simplest
choice. The administrative burden could also be mitigated by using
automated management tools.
Connection redundancy should also be noted as an important
requirement in 3GPP networks. Static tunnels alone do not provide a
routing recovery solution for all scenarios where an IPv6 route goes
down. However, they can provide an adequate solution depending on
the design of the network and the presence of other router redundancy
mechanisms, such as the use of IPv6 routing protocols.
Wiljakka Informational [Page 9]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
3.2.2. Tunneling Outside the 3GPP Operator's Network
This subsection includes the case in which the peer node is outside
the operator's network. In that case, IPv6-in-IPv4 tunneling can be
necessary to obtain IPv6 connectivity and reach other IPv6 nodes. In
general, configured tunneling can be recommended.
Tunnel starting point can be in the operator's network depending on
how far the 3GPP operator has come in implementing IPv6. If the 3GPP
operator has not deployed IPv6 in its backbone, the encapsulating
node can be the GGSN. If the 3GPP operator has deployed IPv6 in its
backbone but the upstream ISP does not provide IPv6 connectivity, the
encapsulating node could be the 3GPP operator's border router.
The case is pretty straightforward if the upstream ISP provides IPv6
connectivity to the Internet and the operator's backbone network
supports IPv6. Then the 3GPP operator does not have to configure any
tunnels, since the upstream ISP will take care of routing IPv6
packets. If the upstream ISP does not provide IPv6 connectivity, an
IPv6-in-IPv4 tunnel should be configured, e.g., from the border
router to a dual stack border gateway operated by another ISP that is
offering IPv6 connectivity.
3.3. IPv4 UE Connecting to an IPv4 Node through an IPv6 Network
3GPP networks are expected to support both IPv4 and IPv6 for a long
time, on the UE-GGSN link and between the GGSN and external networks.
For this scenario, it is useful to split the end-to-end IPv4 UE to
IPv4 node communication into UE-to-GGSN and GGSN-to-v4NODE. This
allows an IPv4-only UE to use an IPv4 link (an IPv4 PDP context) to
connect to the GGSN without communicating over an IPv6 network.
Regarding the GGSN-to-v4NODE communication, typically the transport
network between the GGSN and external networks will support only IPv4
in the early stages and migrate to dual stack, since these networks
are already deployed. Therefore, it is not envisaged that tunneling
of IPv4-in-IPv6 will be required from the GGSN to external IPv4
networks either. In the longer run, 3GPP operators may choose to
phase out IPv4 UEs and the IPv4 transport network. This would leave
only IPv6 UEs.
Therefore, overall, the transition scenario involving an IPv4 UE
communicating with an IPv4 peer through an IPv6 network is not
considered very likely in 3GPP networks.
Wiljakka Informational [Page 10]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
3.4. IPv6 UE Connecting to an IPv4 Node
Generally speaking, IPv6-only UEs may be easier to manage, but that
would require all services to be used over IPv6, and the universal
deployment of IPv6 probably is not realistic in the near future.
Dual stack implementation requires management of both IPv4 and IPv6
networks, and one approach is that "legacy" applications keep using
IPv4 for the foreseeable future and new applications requiring end-
to-end connectivity (for example, peer-to-peer services) use IPv6.
As a general guideline, IPv6-only UEs are not recommended in the
early phases of transition until the IPv6 deployment has become so
prevalent that direct communication with IPv4(-only) nodes will be
the exception and not the rule. It is assumed that IPv4 will remain
useful for quite a long time, so in general, dual stack
implementation in the UE can be recommended. This recommendation
naturally includes manufacturing dual stack UEs instead of IPv4-only
UEs.
However, if there is a need to connect to an IPv4(-only) node from an
IPv6-only UE, it is recommended to use specific translation and
proxying techniques; generic IP protocol translation is not
recommended. There are three main ways for IPv6(-only) nodes to
communicate with IPv4(-only) nodes (excluding avoiding such
communication in the first place):
1. the use of generic-purpose translator (e.g., NAT-PT [RFC2766])
in the local network (not recommended as a general solution),
2. the use of specific-purpose protocol relays (e.g., IPv6<->IPv4
TCP relay configured for a couple of ports only [RFC3142]) or
application proxies (e.g., HTTP proxy, SMTP relay) in the local
network, or
3. the use of specific-purpose mechanisms (as described above in
2) in the foreign network; these are indistinguishable from the
IPv6-enabled services from the IPv6 UE's perspective and are
not discussed further here.
For many applications, application proxies can be appropriate (e.g.,
HTTP proxies, SMTP relays, etc.) Such application proxies will not
be transparent to the UE. Hence, a flexible mechanism with minimal
manual intervention should be used to configure these proxies on IPv6
UEs. Application proxies can be placed, for example, on the GGSN
external interface ("Gi"), or inside the service network.
Wiljakka Informational [Page 11]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
The authors note that [NATPTappl] discusses the applicability of
NAT-PT, and [NATPTexp] discusses general issues with all forms of
IPv6-IPv4 translation. The problems related to NAT-PT usage in 3GPP
networks are documented in Appendix A.
3.5. IPv4 UE Connecting to an IPv6 Node
The legacy IPv4 nodes are typically nodes that support the
applications that are popular today in the IPv4 Internet: mostly e-
mail and web browsing. These applications will, of course, be
supported in the future IPv6 Internet. However, the legacy IPv4 UEs
are not going to be updated to support future applications. As these
applications are designed for IPv6, and to use the advantages of
newer platforms, the legacy IPv4 nodes will not be able to take
advantage of them. Thus, they will continue to support legacy
services.
Taking the above into account, the traffic to and from the legacy
IPv4 UE is restricted to a few applications. These applications
already mostly rely on proxies or local servers to communicate
between private address space networks and the Internet. The same
methods and technology can be used for IPv4-to-IPv6 transition.
4. IMS Transition Scenarios
As IMS is exclusively IPv6, the number of possible transition
scenarios is reduced dramatically. The possible IMS scenarios are
listed below and analyzed in Sections 4.1 and 4.2.
1) UE connecting to a node in an IPv4 network through IMS
2) Two IPv6 IMS connected via an IPv4 network
For DNS recommendations, we refer to Section 2.4. As DNS traffic is
not directly related to the IMS functionality, the recommendations
are not in contradiction with the IPv6-only nature of the IMS.
4.1. UE Connecting to a Node in an IPv4 Network through IMS
This scenario occurs when an (IPv6) IMS UE connects to a node in the
IPv4 Internet through the IMS, or vice versa. This happens when the
other node is a part of a different system than 3GPP, e.g., a fixed
PC, with only IPv4 capabilities.
Over time, users will upgrade the legacy IPv4 nodes to dual-stack,
often by replacing the entire node, eliminating this particular
problem in that specific deployment.
Wiljakka Informational [Page 12]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
Still, it is difficult to estimate how many non-upgradable legacy
IPv4 nodes need to communicate with the IMS UEs. It is assumed that
the solution described here is used for limited cases, in which
communications with a small number of legacy IPv4 SIP equipment are
needed.
As the IMS is exclusively IPv6 [3GPP-23.221], for many of the
applications in the IMS, some kind of translators may need to be used
in the communication between the IPv6 IMS and the legacy IPv4 hosts
in cases where these legacy IPv4 hosts cannot be upgraded to support
IPv6.
This section gives a brief analysis of the IMS interworking issues
and presents a high-level view of SIP within the IMS. The authors
recommend that a detailed solution for the general SIP/SDP/media
IPv4/IPv6 transition problem will be specified as soon as possible as
a task within the SIP-related Working Groups in the IETF.
The issue of the IPv4/IPv6 interworking in SIP is somewhat more
challenging than many other protocols. The control (or signaling)
and user (or data) traffic are separated in SIP calls, and thus, the
IMS, the transition of IMS traffic from IPv6 to IPv4, must be handled
at two levels:
1. Session Initiation Protocol (SIP) [RFC3261], and Session
Description Protocol (SDP) [RFC2327] [RFC3266] (Mm-interface)
2. the user data traffic (Mb-interface)
In addition, SIP carries an SDP body containing the addressing and
other parameters for establishing the user data traffic (the media).
Hence, the two levels of interworking cannot be made independently.
Figure 1 shows an example setup for IPv4 and IPv6 interworking in
IMS. The "Interworking Unit" comprises two internal elements a dual
stack SIP server and a transition gateway (TrGW) for the media
traffic. These two elements are interconnected for synchronizing the
interworking of the SIP signaling and the media traffic.
Wiljakka Informational [Page 13]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
+-------------------------------+ +------------+
| +------+ | | +--------+ |
| |S-CSCF|---| |SIP Serv| |\
| | +------+ | | +--------+ | \ --------
+-|+ | / | | | | | |
| | | +------+ +------+ | | + | -| |-
| |-|-|P-CSCF|--------|I-CSCF| | | | | | () |
| | +------+ +------+ | |+----------+| / ------
| |-----------------------------------|| TrGW ||/
+--+ | IPv6 | |+----------+| IPv4
UE | | |Interworking|
| IP Multimedia CN Subsystem | |Unit |
+-------------------------------+ +------------+
Figure 1: UE using IMS to contact a legacy phone
On reception of an INVITE, the SIP server reserves an IP address and
a port from the TrGW both for IPv4 and IPv6. Then, the SIP server
acts as a B2BUA (Back-to-Back User Agent) and rewrites the SDP of the
INVITE to insert the transition gateway in the middle of the media
flow between the two endpoints.
When performing its B2BUA role, the SIP server acts as a UA (User
Agent) toward both the IMS and the IPv4 host. Consequently, the SIP
server needs to support all the extensions that apply to the session,
which are listed in the Require header fields of the SIP messages.
This approach has a number of important drawbacks, however. The
biggest drawback is that the rewriting of the SDP in the SIP
signaling prevents securing the SDP payload between the two
endpoints. In addition, it breaks the end-to-end negotiation of SIP
extensions required for each session. Therefore, the extensions to
be used in a particular session are limited by the extensions
supported by the SIP server acting as a B2BUA. That is, the
introduction of a new extension requires upgrading not only the UAs
but the B2BUAs as well.
This analysis clearly shows that a new solution for IPv4-IPv6
interworking in SIP networks is needed. The ability to convey
multiple alternative addresses in SDP session descriptions [RFC4091]
represents a step in this direction.
Given the problems related to the use of B2BUAs, it is recommended
that the SIP-related Working Groups quickly work on a solution to
overcome the drawbacks of this approach.
Wiljakka Informational [Page 14]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
4.2. Two IPv6 IMS Connected via an IPv4 Network
At the early stages of IMS deployment, there may be cases where two
IMS islands are separated by an IPv4 network such as the legacy
Internet. Here both the UEs and the IMS islands are IPv6 only.
However, the IPv6 islands are not connected natively with IPv6.
In this scenario, the end-to-end SIP connections are based on IPv6.
The only issue is to make connection between two IPv6-only IMS
islands over IPv4 network. This scenario is closely related to GPRS
scenario represented in Section 3.2. and similar tunneling solutions
are applicable also in this scenario.
5. About 3GPP UE IPv4/IPv6 Configuration
This informative section aims to give a brief overview of the
configuration needed in the UE in order to access IP-based services.
There can also be other application-specific settings in the UE that
are not described here.
UE configuration is required in order to access IPv6- or IPv4-based
services. The GGSN Access Point has to be defined when using, for
example, the web-browsing application. One possibility is to use
over-the-air configuration [OMA-CP] to configure the GPRS settings.
The user can, for example, visit the operator WWW page and subscribe
the GPRS Access Point settings to his/her UE and receive the settings
via Short Message Service (SMS). After the user has accepted the
settings and a PDP context has been activated, he/she can start
browsing. The Access Point settings can also be typed in manually or
be pre-configured by the operator or the UE manufacturer.
DNS server addresses typically also need to be configured in the UE.
In the case of IPv4 type PDP context, the (IPv4) DNS server addresses
can be received in the PDP context activation (a control plane
mechanism). A similar mechanism is also available for IPv6: so-
called Protocol Configuration Options Information Element (PCO-IE)
specified by the 3GPP [3GPP-24.008]. It is also possible to use
[RFC3736] (or [RFC3315]) and [RFC3646] for receiving DNS server
addresses. Active IETF work on DNS discovery mechanisms is ongoing
and might result in other mechanisms becoming available over time.
The DNS server addresses can also be received over the air (using
SMS) [OMA-CP] or typed in manually in the UE.
When accessing IMS services, the UE needs to know the Proxy-Call
Session Control Function (P-CSCF) IPv6 address. Either a 3GPP-
specific PCO-IE mechanism or a DHCPv6-based mechanism ([RFC3736] and
[RFC3319]) can be used. Manual configuration or configuration over
Wiljakka Informational [Page 15]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
the air is also possible. IMS subscriber authentication and
registration to the IMS and SIP integrity protection are not
discussed here.
6. Summary and Recommendations
This document has analyzed five GPRS and two IMS IPv6 transition
scenarios. Numerous 3GPP networks are using private IPv4 addresses
today, and introducing IPv6 is important. The two first GPRS
scenarios and both IMS scenarios are seen as the most relevant. The
authors summarize some main recommendations here:
- Dual stack UEs are recommended instead of IPv4-only or IPv6-
only UEs. It is important to take care that applications in
the UEs support IPv6. In other words, applications should be
IP version independent. IPv6-only UEs can become feasible when
IPv6 is widely deployed in the networks, and most services work
on IPv6.
- It is recommended to activate an IPv6 PDP context when
communicating with an IPv6 peer node and an IPv4 PDP context
when communicating with an IPv4 peer node.
- IPv6 communication is preferred to IPv4 communication going
through IPv4 NATs to the same dual stack peer node.
- This document strongly recommends that the 3GPP operators
deploy basic IPv6 support in their GPRS networks as soon as
possible. That makes it possible to lessen the transition
effects in the UEs.
- A tunneling mechanism in the UE may be needed during the early
phases of the IPv6 transition process. A lightweight,
automatic tunneling mechanism should be standardized in the
IETF. See [zeroconf] for more details.
- Tunneling mechanisms can be used in 3GPP networks, and only
generic recommendations are given in this document. More
details can be found, for example, in [RFC4029].
- The authors recommend that a detailed solution for the general
SIP/SDP/media IPv4/IPv6 transition problem be specified as soon
as possible as a task within the SIP-related Working Groups in
the IETF.
Wiljakka Informational [Page 16]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
7. Security Considerations
Deploying IPv6 has some generic security considerations one should be
aware of [V6SEC]; however, these are not specific to 3GPP transition
and are therefore out of the scope of this memo.
This memo recommends the use of a relatively small number of
techniques. Each technique has its own security considerations,
including:
- native upstream access or tunneling by the 3GPP network
operator,
- use of routing protocols to ensure redundancy,
- use of locally deployed specific-purpose protocol relays and
application proxies to reach IPv4(-only) nodes from IPv6-only
UEs, or
- a specific mechanism for SIP signaling and media translation.
The threats of configured tunneling are described in [RFC4213].
Attacks against routing protocols are described in the respective
documents and in general in [ROUTESEC]. Threats related to protocol
relays have been described in [RFC3142]. The security properties of
SIP internetworking are to be specified when the mechanism is
specified.
In particular, this memo does not recommend the following technique,
which has security issues, not further analyzed here:
- NAT-PT or other translator as a general-purpose transition
mechanism
8. References
8.1. Normative References
[RFC2663] Srisuresh, P. and M. Holdrege, "IP Network Address
Translator (NAT) Terminology and Considerations", RFC
2663, August 1999.
[RFC2765] Nordmark, E., "Stateless IP/ICMP Translation Algorithm
(SIIT)", RFC 2765, February 2000.
[RFC2766] Tsirtsis, G. and P. Srisuresh, "Network Address
Translation - Protocol Translation (NAT-PT)", RFC 2766,
February 2000.
Wiljakka Informational [Page 17]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G.,
Johnston, A., Peterson, J., Sparks, R., Handley, M.,
and E. Schooler, "SIP: Session Initiation Protocol",
RFC 3261, June 2002.
[RFC3574] Soininen, J., "Transition Scenarios for 3GPP Networks",
RFC 3574, August 2003.
[RFC4213] Nordmark, E. and R. Gilligan, "Basic Transition
Mechanisms for IPv6 Hosts and Routers", RFC 4213,
October 2005.
[3GPP-23.060] 3GPP TS 23.060 V5.4.0, "General Packet Radio Service
(GPRS); Service description; Stage 2 (Release 5)",
December 2002.
[3GPP-23.221] 3GPP TS 23.221 V5.7.0, "Architectural requirements
(Release 5)", December 2002.
[3GPP-23.228] 3GPP TS 23.228 V5.7.0, "IP Multimedia Subsystem (IMS);
Stage 2 (Release 5)", December 2002.
[3GPP-24.228] 3GPP TS 24.228 V5.3.0, "Signalling flows for the IP
multimedia call control based on SIP and SDP; Stage 3
(Release 5)", December 2002.
[3GPP-24.229] 3GPP TS 24.229 V5.3.0, "IP Multimedia Call Control
Protocol based on SIP and SDP; Stage 3 (Release 5)",
December 2002.
8.2. Informative References
[RFC2327] Handley, M. and V. Jacobson, "SDP: Session Description
Protocol", RFC 2327, April 1998.
[RFC3142] Hagino, J. and K. Yamamoto, "An IPv6-to-IPv4 Transport
Relay Translator", RFC 3142, June 2001.
[RFC3266] Olson, S., Camarillo, G., and A. Roach, "Support for
IPv6 in Session Description Protocol (SDP)", RFC 3266,
June 2002.
[RFC3314] Wasserman, M., "Recommendations for IPv6 in Third
Generation Partnership Project (3GPP) Standards", RFC
3314, September 2002.
Wiljakka Informational [Page 18]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C.,
and M. Carney, "Dynamic Host Configuration Protocol for
IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC3319] Schulzrinne, H. and B. Volz, "Dynamic Host
Configuration Protocol (DHCPv6) Options for Session
Initiation Protocol (SIP) Servers", RFC 3319, July
2003.
[RFC3646] Droms, R., "DNS Configuration options for Dynamic Host
Configuration Protocol for IPv6 (DHCPv6)", RFC 3646,
December 2003.
[RFC3736] Droms, R., "Stateless Dynamic Host Configuration
Protocol (DHCP) Service for IPv6", RFC 3736, April
2004.
[RFC3901] Durand, A. and J. Ihren, "DNS IPv6 Transport
Operational Guidelines", BCP 91, RFC 3901, September
2004.
[RFC4029] Lind, M., Ksinant, V., Park, S., Baudot, A., and P.
Savola, "Scenarios and Analysis for Introducing IPv6
into ISP Networks", RFC 4029, March 2005.
[RFC4091] Camarillo, G. and J. Rosenberg, "The Alternative
Network Address Types (ANAT) Semantics for the Session
Description Protocol (SDP) Grouping Framework", RFC
4091, June 2005.
[ISATAP] Templin, F., Gleeson, T., Talwar, M., and D. Thaler,
"Intra-Site Automatic Tunnel Addressing Protocol
(ISATAP)", RFC 4214, September 2005.
[NATPTappl] Satapati, S., Sivakumar, S., Barany, P., Okazaki, S.
and H. Wang, "NAT-PT Applicability", Work in Progress,
October 2003.
[NATPTexp] Aoun, C. and E. Davies, "Reasons to Move NAT-PT to
Experimental", Work in Progress, July 2005.
[ROUTESEC] Barbir, A., Murphy, S., and Y. Yang, "Generic Threats
to Routing Protocols", Work in Progress, April 2004.
[STEP] Savola, P.: "Simple IPv6-in-IPv4 Tunnel Establishment
Procedure (STEP)", Work in Progress, January 2004.
Wiljakka Informational [Page 19]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
[V6SEC] Savola, P.: "IPv6 Transition/Co-existence Security
Considerations", Work in Progress, February 2004.
[zeroconf] Nielsen, K., Morelli, M., Palet, J., Soininen, J., and
J. Wiljakka, "Goals for Zero-Configuration Tunneling in
3GPP", Work in Progress, October 2004.
[3GPP-24.008] 3GPP TS 24.008 V5.8.0, "Mobile radio interface Layer 3
specification; Core network protocols; Stage 3 (Release
5)", June 2003.
[OMA-CP] OMA Client Provisioning: Provisioning Architecture
Overview Version 1.1, OMA-WAP-ProvArch-v1_1-20021112-C,
Open Mobile Alliance, 12-Nov-2002.
9. Contributors
Pekka Savola has contributed both text and his IPv6 experience to
this document. He has provided a large number of helpful comments on
the v6ops mailing list. Allison Mankin has contributed text for IMS
Scenario 1 (Section 4.1).
10. Authors and Acknowledgements
This document was written by:
Alain Durand, Comcast
<alain_durand@cable.comcast.com>
Karim El-Malki, Ericsson Radio Systems
<Karim.El-Malki@era.ericsson.se>
Niall Richard Murphy, Enigma Consulting Limited
<niallm@enigma.ie>
Hugh Shieh, AT&T Wireless
<hugh.shieh@attws.com>
Jonne Soininen, Nokia
<jonne.soininen@nokia.com>
Hesham Soliman, Flarion
<h.soliman@flarion.com>
Wiljakka Informational [Page 20]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
Margaret Wasserman, ThingMagic
<margaret@thingmagic.com>
Juha Wiljakka, Nokia
<juha.wiljakka@nokia.com>
The authors would like to give special thanks to Spencer Dawkins for
proofreading.
The authors would like to thank Heikki Almay, Gabor Bajko, Gonzalo
Camarillo, Ajay Jain, Jarkko Jouppi, David Kessens, Ivan Laloux,
Allison Mankin, Jasminko Mulahusic, Janne Rinne, Andreas Schmid,
Pedro Serna, Fred Templin, Anand Thakur, and Rod Van Meter for their
valuable input.
Wiljakka Informational [Page 21]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
Appendix A - On the Use of Generic Translators in the 3GPP Networks
This appendix lists mainly 3GPP-specific arguments about generic
translators, even though the use of generic translators is
discouraged.
Due to the significant lack of IPv4 addresses in some domains, port
multiplexing is likely to be a necessary feature for translators
(i.e., NAPT-PT). If NAPT-PT is used, it needs to be placed on the
GGSN external interface (Gi), typically separate from the GGSN.
NAPT-PT can be installed, for example, on the edge of the operator's
network and the public Internet. NAPT-PT will intercept DNS requests
and other applications that include IP addresses in their payloads,
translate the IP header (and payload for some applications if
necessary), and forward packets through its IPv4 interface.
NAPT-PT introduces limitations that are expected to be magnified
within the 3GPP architecture. [NATPTappl] discusses the
applicability of NAT-PT in more detail. [NATPTexp] discusses general
issues with all forms of IPv6-IPv4 translation.
3GPP networks are expected to handle a very large number of
subscribers on a single GGSN (default router). Each GGSN is expected
to handle hundreds of thousands of connections. Furthermore, high
reliability is expected for 3GPP networks. Consequently, a single
point of failure on the GGSN external interface would raise concerns
on the overall network reliability. In addition, IPv6 users are
expected to use delay-sensitive applications provided by IMS. Hence,
there is a need to minimize forwarding delays within the IP backbone.
Furthermore, due to the unprecedented number of connections handled
by the default routers (GGSN) in 3GPP networks, a network design that
forces traffic to go through a single node at the edge of the network
(typical NAPT-PT configuration) is not likely to scale. Translation
mechanisms should allow for multiple translators, for load sharing
and redundancy purposes.
To minimize the problems associated with NAPT-PT, the following
actions can be recommended:
1. Separate the DNS ALG from the NAPT-PT node (in the "IPv6 to
IPv4" case).
2. Ensure (if possible) that NAPT-PT does not become a single
point of failure.
Wiljakka Informational [Page 22]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
3. Allow for load sharing between different translators. That is,
it should be possible for different connections to go through
different translators. Note that load sharing alone does not
prevent NAPT-PT from becoming a single point of failure.
Editor's Contact Information
Comments or questions regarding this document should be sent to the
v6ops mailing list or directly to the document editor:
Juha Wiljakka
Nokia
Visiokatu 3
FIN-33720 TAMPERE, Finland
Phone: +358 7180 48372
EMail: juha.wiljakka@nokia.com
Wiljakka Informational [Page 23]
RFC 4215 IPv6 Transition in 3GPP Networks October 2005
Full Copyright Statement
Copyright (C) The Internet Society (2005).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at ietf-
ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Wiljakka Informational [Page 24]