💾 Archived View for gmi.noulin.net › man › man2 › close.2.gmi captured on 2024-06-16 at 12:36:45. Gemini links have been rewritten to link to archived content
⬅️ Previous capture (2022-06-12)
-=-=-=-=-=-=-
CLOSE(2) Linux Programmer's Manual CLOSE(2)
NAME
close - close a file descriptor
SYNOPSIS
#include <unistd.h>
int close(int fd);
DESCRIPTION
close() closes a file descriptor, so that it no longer refers to any file and may be reused. Any record locks (see fcntl(2)) held on the file it was associated
with, and owned by the process, are removed (regardless of the file descriptor that was used to obtain the lock).
If fd is the last file descriptor referring to the underlying open file description (see open(2)), the resources associated with the open file description are
freed; if the file descriptor was the last reference to a file which has been removed using unlink(2), the file is deleted.
RETURN VALUE
close() returns zero on success. On error, -1 is returned, and errno is set to indicate the error.
ERRORS
EBADF fd isn't a valid open file descriptor.
EINTR The close() call was interrupted by a signal; see signal(7).
EIO An I/O error occurred.
ENOSPC, EDQUOT
On NFS, these errors are not normally reported against the first write which exceeds the available storage space, but instead against a subsequent
write(2), fsync(2), or close().
See NOTES for a discussion of why close() should not be retried after an error.
CONFORMING TO
POSIX.1-2001, POSIX.1-2008, SVr4, 4.3BSD.
NOTES
A successful close does not guarantee that the data has been successfully saved to disk, as the kernel uses the buffer cache to defer writes. Typically,
filesystems do not flush buffers when a file is closed. If you need to be sure that the data is physically stored on the underlying disk, use fsync(2). (It
will depend on the disk hardware at this point.)
The close-on-exec file descriptor flag can be used to ensure that a file descriptor is automatically closed upon a successful execve(2); see fcntl(2) for de‐
tails.
Multithreaded processes and close()
It is probably unwise to close file descriptors while they may be in use by system calls in other threads in the same process. Since a file descriptor may be
reused, there are some obscure race conditions that may cause unintended side effects.
Furthermore, consider the following scenario where two threads are performing operations on the same file descriptor:
1. One thread is blocked in an I/O system call on the file descriptor. For example, it is trying to write(2) to a pipe that is already full, or trying to
read(2) from a stream socket which currently has no available data.
2. Another thread closes the file descriptor.
The behavior in this situation varies across systems. On some systems, when the file descriptor is closed, the blocking system call returns immediately with an
error.
On Linux (and possibly some other systems), the behavior is different: the blocking I/O system call holds a reference to the underlying open file description,
and this reference keeps the description open until the I/O system call completes. (See open(2) for a discussion of open file descriptions.) Thus, the blocking
system call in the first thread may successfully complete after the close() in the second thread.
Dealing with error returns from close()
A careful programmer will check the return value of close(), since it is quite possible that errors on a previous write(2) operation are reported only on the fi‐
nal close() that releases the open file description. Failing to check the return value when closing a file may lead to silent loss of data. This can especially
be observed with NFS and with disk quota.
Note, however, that a failure return should be used only for diagnostic purposes (i.e., a warning to the application that there may still be I/O pending or there
may have been failed I/O) or remedial purposes (e.g., writing the file once more or creating a backup).
Retrying the close() after a failure return is the wrong thing to do, since this may cause a reused file descriptor from another thread to be closed. This can
occur because the Linux kernel always releases the file descriptor early in the close operation, freeing it for reuse; the steps that may return an error, such
as flushing data to the filesystem or device, occur only later in the close operation.
Many other implementations similarly always close the file descriptor (except in the case of EBADF, meaning that the file descriptor was invalid) even if they
subsequently report an error on return from close(). POSIX.1 is currently silent on this point, but there are plans to mandate this behavior in the next major
release of the standard.
A careful programmer who wants to know about I/O errors may precede close() with a call to fsync(2).
The EINTR error is a somewhat special case. Regarding the EINTR error, POSIX.1-2008 says:
If close() is interrupted by a signal that is to be caught, it shall return -1 with errno set to EINTR and the state of fildes is unspecified.
This permits the behavior that occurs on Linux and many other implementations, where, as with other errors that may be reported by close(), the file descriptor
is guaranteed to be closed. However, it also permits another possibility: that the implementation returns an EINTR error and keeps the file descriptor open.
(According to its documentation, HP-UX's close() does this.) The caller must then once more use close() to close the file descriptor, to avoid file descriptor
leaks. This divergence in implementation behaviors provides a difficult hurdle for portable applications, since on many implementations, close() must not be
called again after an EINTR error, and on at least one, close() must be called again. There are plans to address this conundrum for the next major release of
the POSIX.1 standard.
SEE ALSO
close_range(2), fcntl(2), fsync(2), open(2), shutdown(2), unlink(2), fclose(3)
Linux 2021-03-22 CLOSE(2)