💾 Archived View for gmi.noulin.net › rfc › rfc3872.gmi captured on 2024-05-26 at 17:30:08. Gemini links have been rewritten to link to archived content

View Raw

More Information

⬅️ Previous capture (2023-01-29)

-=-=-=-=-=-=-

Keywords: mib, management information base, TRIP, Telephony Routing over IP







Network Working Group                                          D. Zinman
Request for Comments: 3872                                     D. Walker
Category: Standards Track                                       J. Jiang
                                                          September 2004


                      Management Information Base
                  for Telephony Routing over IP (TRIP)

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2004).

Abstract

   This memo defines a portion of the Management Information Base (MIB)
   module for use with network management protocols in the Internet
   community.  In particular, it describes a set of managed objects that
   are used to manage Telephony Routing over IP (TRIP) devices.

Table of Contents

   1.  The Internet-Standard Management Framework . . . . . . . . . .  2
   2.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  2
   3.  Conventions used in this document. . . . . . . . . . . . . . .  2
   4.  Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
   5.  Structure of TRIP MIB. . . . . . . . . . . . . . . . . . . . .  2
       5.1.  Textual Conventions. . . . . . . . . . . . . . . . . . .  3
   6.  Definitions. . . . . . . . . . . . . . . . . . . . . . . . . .  4
       6.1.  TRIP Textual Conventions . . . . . . . . . . . . . . . .  4
       6.2.  TRIP MIB . . . . . . . . . . . . . . . . . . . . . . . .  7
   7.  Security Considerations. . . . . . . . . . . . . . . . . . . . 48
   8.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 50
       8.1.  Normative References . . . . . . . . . . . . . . . . . . 50
       8.2.  Informative References . . . . . . . . . . . . . . . . . 51
   9.  Acknowledgments. . . . . . . . . . . . . . . . . . . . . . . . 51
   10. Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . 52
   11. Full Copyright Statement . . . . . . . . . . . . . . . . . . . 53





Zinman, et al.              Standards Track                     [Page 1]

RFC 3872                      MIB for TRIP                September 2004


1.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB module objects are
   generally accessed through the Simple Network Management Protocol
   (SNMP).  Objects in this MIB module are defined using the mechanisms
   defined in the Structure of Management Information (SMI).  This memo
   specifies a MIB module that is compliant to the SMIv2, which is
   described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579],
   and STD 58, RFC 2580 [RFC2580].

2.  Introduction

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it describes a set of managed objects that are used
   to schedule management operations periodically or at specified dates
   and times.  Since TRIP [RFC3219] is modeled after the Border Gateway
   Protocol (BGP-4) [RFC1771], the managed objects for TRIP are also
   modeled after RFC1657 - Definitions of Managed Objects for the
   Fourth Version of the Border Gateway Protocol (BGP-4) using SMIv2
   [RFC1657].

3.  Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
   this document are to be interpreted as described in BCP 14, RFC 2119
   [RFC2119].

4.  Overview

   This MIB module provides managed objects for TRIP devices defined in
   Telephony Routing over IP [RFC3219].  TRIP is an inter-domain
   application-layer control protocol that exchanges information
   between TRIP location servers (LS) to provide efficient IP telephony
   routing.

5.  Structure of TRIP MIB

   This MIB module utilizes the framework described in RFC 2788
   [RFC2788] for management of multiple instances of TRIP from a single
   entity.  The Network Services Monitoring MIB module applTable will
   be populated with entries corresponding to each TRIP Location Server



Zinman, et al.              Standards Track                     [Page 2]

RFC 3872                      MIB for TRIP                September 2004


   in the system.  Each TRIP Location Server will then have an
   applIndex associated with it.  The value assigned to applIndex will
   represent the distinct instance of TRIP.

   The TRIP MIB module contains the following groups of objects with
   each group as part of the management of a singular TRIP entity.  Each
   group covers a section of functionality of TRIP:

   o  The tripConfigGroup contains the common configuration objects
      applicable to all TRIP applications referenced by the applIndex.

   o  The tripPeerTableConfigGroup contains the configuration objects
      applicable to all TRIP peers of the Location Server referenced by
      the applIndex.

   o  The tripRouteGroup contains the configuration objects related to
      the routes of all TRIBs of this Location Server.

   o  The tripItadTopologyGroup contains information about the topology
      of the TRIP ITADs concerning this Location Server.

   o  The tripPeerTableStatsGroup contains the statistical objects
      applicable to all TRIP peers of the Location Server referenced by
      the applIndex.

   o  The tripNotificationGroup contains notifications that the TRIP
      application can generate.

   o  The tripNotifObjectGroup contains the objects needed by one or
      more of the notifications.

5.1.  Textual Conventions

   The data types TripItad and TripId are used as textual conventions
   in this document.  A TRIP ITAD (IP Telephony Administrative Domain)
   is described in [RFC3219].  A TRIP ID is used as a distinct
   identifier for a TRIP Location Server.  A TripAppProtocol is used to
   identify an application protocol.  A TripAddressFamily is used to
   define an address family.  TripCommunityId is used as a distinct
   identifier for a TRIP community.  TripProtocolVersion depicts the
   version number of the TRIP protocol.  TripSendReceiveMode describes
   the operational mode of the TRIP application.









Zinman, et al.              Standards Track                     [Page 3]

RFC 3872                      MIB for TRIP                September 2004


6.  Definitions

6.1.  TRIP Textual Conventions

TRIP-TC-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY,
    Unsigned32,
    Integer32,
    mib-2
        FROM SNMPv2-SMI            -- [RFC2578]

    TEXTUAL-CONVENTION
        FROM SNMPv2-TC;            -- [RFC2579]

tripTC MODULE-IDENTITY
    LAST-UPDATED   "200409020000Z" -- Sep 02, 2004
    ORGANIZATION   "IETF IPTel Working Group.
        Mailing list: iptel@lists.bell-labs.com"
    CONTACT-INFO
       "Co-editor  David Zinman
        postal:    265 Ridley Blvd.
                   Toronto ON, M5M 4N8
                   Canada
        email:     dzinman@rogers.com
        phone:     +1 416 433 4298

        Co-editor: David Walker
                   Sedna Wireless Inc.
        postal:    495 March Road, Suite 500
                   Ottawa, ON K2K 3G1
                   Canada
        email:     david.walker@sedna-wireless.com
        phone:     +1 613 878 8142

        Co-editor   Jianping Jiang
                    Syndesis Limited
        postal:     30 Fulton Way
                    Richmond Hill, ON L4B 1J5
                    Canada

        email:      jjiang@syndesis.com
        phone:      +1 905 886-7818 x2515
        "
    DESCRIPTION
        "Initial version of TRIP (Telephony Routing Over IP)
        MIB Textual Conventions module used by other



Zinman, et al.              Standards Track                     [Page 4]

RFC 3872                      MIB for TRIP                September 2004


        TRIP-related MIB Modules.

        Copyright (C) The Internet Society (2004). This version of
        this MIB module is part of RFC 3872, see the RFC itself
        for full legal notices."
    REVISION      "200409020000Z" -- Sep 02, 2004
    DESCRIPTION
        "The initial version, Published as RFC 3872."
    ::= { mib-2 115 }

--
-- Textual Conventions
--

TripItad ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
       "The values for identifying the IP Telephony
       Administrative Domain (ITAD)."
    SYNTAX Unsigned32 (0..4294967295)

TripId ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
       "The TRIP Identifier uniquely identifies a LS within its
       ITAD. It is a 4 octet unsigned integer that may, but not
       necessarily, represent the IPv4 address of a Location
       Server.  Where bytes 1-4 of the Unsigned32 represent
       1-4 bytes of the IPv4 address in network-byte order. For
       an IPv6 network, TripId will not represent the IPv6
       address."
    SYNTAX Unsigned32 (0..4294967295)

TripAddressFamily ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
        "A type of address for a TRIP route. Address families
        defined within this MIB module are:

        Code              Address Family
        1                 Decimal Routing Numbers
        2                 PentaDecimal Routing Numbers
        3                 E.164 Numbers
        255               An other type of address family"

    SYNTAX INTEGER
        { decimal(1), pentadecimal(2), e164(3), other(255) }




Zinman, et al.              Standards Track                     [Page 5]

RFC 3872                      MIB for TRIP                September 2004


TripAppProtocol ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
        "The application protocol used for communication with TRIP
        Location Servers. Protocols defined in this MIB Module
        are:

        Code              Protocol
        1                 SIP
        2                 H.323-H.225.0-Q.931
        3                 H.323-H.225.0-RAS
        4                 H.323-H.225.0-Annex-G
        255               An other type of application protocol"

    SYNTAX INTEGER
        { sip(1), q931(2), ras(3), annexG(4), other(255) }

TripCommunityId ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
       "The range of legal values for a TRIP Community
       Identifier."
    SYNTAX Unsigned32 (0..4294967295)

TripProtocolVersion ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
       "The version number of the TRIP protocol."
    SYNTAX Integer32 (1..255)

TripSendReceiveMode ::= TEXTUAL-CONVENTION
    STATUS current
    DESCRIPTION
       "The operational mode of the TRIP application. Possible
       values are:
          1 - Send Receive mode
          2 - Send only mode
          3 - Receive Only mode"
    SYNTAX INTEGER { sendReceive(1), sendOnly(2), receiveOnly(3) }

END










Zinman, et al.              Standards Track                     [Page 6]

RFC 3872                      MIB for TRIP                September 2004


6.2.  TRIP MIB

TRIP-MIB DEFINITIONS ::= BEGIN

    IMPORTS
        MODULE-IDENTITY,
        OBJECT-TYPE,
        NOTIFICATION-TYPE,
        Unsigned32,
        Integer32,
        Counter32,
        mib-2
            FROM SNMPv2-SMI           -- [RFC2578]

        DateAndTime,
        TimeInterval,
        TruthValue,
        TimeStamp,
        StorageType,
        RowStatus
            FROM SNMPv2-TC            -- [RFC2579]

        OBJECT-GROUP,
        MODULE-COMPLIANCE,
        NOTIFICATION-GROUP
            FROM SNMPv2-CONF          -- [RFC2580]

        InetAddressType,
        InetAddress,
        InetPortNumber
            FROM INET-ADDRESS-MIB     -- [RFC3291]

        applIndex,
        applRFC2788Group
            FROM NETWORK-SERVICES-MIB -- [RFC2788]

        TripItad,
        TripId,
        TripAppProtocol,
        TripAddressFamily,
        TripCommunityId,
        TripProtocolVersion,
        TripSendReceiveMode
            FROM TRIP-TC-MIB;          -- [RFC3872]

    tripMIB MODULE-IDENTITY
       LAST-UPDATED "200409020000Z" -- Sep 02, 2004
           ORGANIZATION "IETF IPTel Working Group.



Zinman, et al.              Standards Track                     [Page 7]

RFC 3872                      MIB for TRIP                September 2004


            Mailing list: iptel@lists.bell-labs.com"

       CONTACT-INFO
           "Co-editor  David Zinman
            postal:    265 Ridley Blvd.
                       Toronto ON, M5M 4N8
                       Canada
            email:     dzinman@rogers.com
            phone:     +1 416 433 4298

        Co-editor: David Walker
                   Sedna Wireless Inc.
        postal:    495 March Road, Suite 500
                   Ottawa, ON K2K 3G1
                   Canada
        email:     david.walker@sedna-wireless.com
        phone:     +1 613 878 8142

        Co-editor   Jianping Jiang
                    Syndesis Limited
        postal:     30 Fulton Way
                    Richmond Hill, ON L4B 1J5
                    Canada

        email:      jjiang@syndesis.com
        phone:      +1 905 886-7818 x2515
            "
        DESCRIPTION
            "The MIB module describing Telephony Routing over IP
            (TRIP). TRIP is a policy driven inter-administrative
            domain protocol for advertising the reachability of
            telephony destinations between location servers (LS), and
            for advertising attributes of the routes to those
            destinations.

            Copyright (C) The Internet Society (2004). This version of
            this MIB module is part of RFC 3872, see the RFC itself
            for full legal notices."
        REVISION      "200409020000Z" -- Sep 02, 2004
        DESCRIPTION
            "The initial version, Published as RFC 3872."
    ::= { mib-2 116 }

        tripMIBNotifications OBJECT IDENTIFIER ::= { tripMIB 0 }
        tripMIBObjects       OBJECT IDENTIFIER ::= { tripMIB 1 }
        tripMIBConformance   OBJECT IDENTIFIER ::= { tripMIB 2 }
        tripMIBNotifObjects  OBJECT IDENTIFIER ::= { tripMIB 3 }




Zinman, et al.              Standards Track                     [Page 8]

RFC 3872                      MIB for TRIP                September 2004


        tripMIBCompliances    OBJECT IDENTIFIER ::=
                                        { tripMIBConformance 1 }
        tripMIBGroups        OBJECT IDENTIFIER ::=
                                        { tripMIBConformance 2 }

   --
   -- tripCfgTable
   --
    tripCfgTable OBJECT-TYPE
        SYNTAX     SEQUENCE OF TripCfgEntry
        MAX-ACCESS not-accessible
        STATUS     current
        DESCRIPTION
            "This table contains the common configuration objects
             applicable to all TRIP applications referenced by the
             applIndex.  Each row represents those objects for a
             particular TRIP LS present in this system. The
             instances of TRIP LS's are uniquely identified by the
             applIndex. The objects in this table SHOULD be
             nonVolatile and survive a reboot."
        ::= { tripMIBObjects 1 }

    tripCfgEntry OBJECT-TYPE
        SYNTAX     TripCfgEntry
        MAX-ACCESS not-accessible
        STATUS     current
        DESCRIPTION
            "A row of common configuration."
        INDEX { applIndex }
        ::= { tripCfgTable 1 }

    TripCfgEntry ::=
        SEQUENCE {
           tripCfgProtocolVersion               TripProtocolVersion,
           tripCfgItad                          TripItad,
           tripCfgIdentifier                    TripId,
           tripCfgAdminStatus                   INTEGER,
           tripCfgOperStatus                    INTEGER,
           tripCfgAddrIAddrType                 InetAddressType,
           tripCfgAddr                          InetAddress,
           tripCfgPort                          InetPortNumber,
           tripCfgMinItadOriginationInterval    Unsigned32,
           tripCfgMinRouteAdvertisementInterval Unsigned32,
           tripCfgMaxPurgeTime                  Unsigned32,
           tripCfgDisableTime                   Unsigned32,
           tripCfgSendReceiveMode               TripSendReceiveMode,
           tripCfgStorage                       StorageType
       }



Zinman, et al.              Standards Track                     [Page 9]

RFC 3872                      MIB for TRIP                September 2004


    tripCfgProtocolVersion    OBJECT-TYPE
        SYNTAX     TripProtocolVersion
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "This object will reflect the version of TRIP
            supported by this system.  It follows the same
            format as TRIP version information contained
            in the TRIP messages generated by this TRIP entity."
        REFERENCE
            "RFC 3219, section 4.2."
        ::= { tripCfgEntry 1 }

    tripCfgItad   OBJECT-TYPE
        SYNTAX      TripItad
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "The Internet Telephony Administrative domain (ITAD)
            of this LS."
        ::= { tripCfgEntry 2 }

    tripCfgIdentifier   OBJECT-TYPE
        SYNTAX      TripId
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The object that identifies this TRIP Client."
        ::= { tripCfgEntry 3 }

    tripCfgAdminStatus OBJECT-TYPE
        SYNTAX      INTEGER {
                        up(1),
                        down(2)
                    }
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "The desired TRIP state.

             up(1)  : Set the application to normal operation.

             down(2): Set the application to a state where it will
                      not process TRIP messages.

             Setting this object should be reflected in
             tripCfgOperStatus. If an unknown error occurs
             tripCfgOperStatus will return unknown(0)."



Zinman, et al.              Standards Track                    [Page 10]

RFC 3872                      MIB for TRIP                September 2004


        ::= { tripCfgEntry 4 }

    tripCfgOperStatus OBJECT-TYPE
        SYNTAX      INTEGER {
                        unknown(0),
                        up(1),
                        down(2),
                        faulty(3)
                    }
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The current operational state of the TRIP protocol.

             unknown(0): The operating status of the application is
                         unknown.

             up(1):      The application is operating normally, and
                         is ready to process (receive and issue) TRIP
                         requests and responses.

             down(2):    The application is currently not processing
                         TRIP messages. This occurs if the TRIP
                         application is in an initialization state or
                         if tripCfgAdminStatus is set to down(2).

             faulty(3):  The application is not operating normally due
                         to a fault in the system.

            If tripCfgAdminStatus is down(2) then tripOperStatus SHOULD
            be down(2). If tripAdminStatus is changed to up(1) then
            tripOperStatus SHOULD change to up(1) if there is no
            fault that prevents the TRIP protocol from moving to the
            up(1) state."
        ::= { tripCfgEntry 5 }

    tripCfgAddrIAddrType OBJECT-TYPE
        SYNTAX      InetAddressType
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The type of Inet Address of the tripAddr."
        REFERENCE
            "RFC 3291, section 3."
        ::= { tripCfgEntry 6 }

    tripCfgAddr OBJECT-TYPE
        SYNTAX      InetAddress



Zinman, et al.              Standards Track                    [Page 11]

RFC 3872                      MIB for TRIP                September 2004


        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The network address of the local LS that the peer
            connects to. The type of address depends on the object
            tripCfgAddrIAddrType. The type of this address is
            determined by the value of the
            tripCfgAddrIAddrType object."
        REFERENCE
            "RFC 3291, section 3."
        ::= { tripCfgEntry 7 }

    tripCfgPort OBJECT-TYPE
        SYNTAX      InetPortNumber
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "The local tcp/udp port on the local LS that the peer
            connects to."
        ::= { tripCfgEntry 8 }

    tripCfgMinItadOriginationInterval OBJECT-TYPE
        SYNTAX      Unsigned32 (1..2147483647)
        UNITS       "Seconds"
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "The minimum amount of time that MUST elapse between
            advertisement of the update message that reports changes
            within the LS's own ITAD."
        DEFVAL { 30 }
        ::= { tripCfgEntry 9 }

    tripCfgMinRouteAdvertisementInterval OBJECT-TYPE
        SYNTAX      Unsigned32 (1..2147483647)
        UNITS       "Seconds"
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "Specifies minimal interval between successive
            advertisements to a particular destination from an LS."
        DEFVAL { 30 }
        ::= { tripCfgEntry 10 }

    tripCfgMaxPurgeTime OBJECT-TYPE
        SYNTAX      Unsigned32 (1..2147483647)
        UNITS       "Seconds"
        MAX-ACCESS  read-write



Zinman, et al.              Standards Track                    [Page 12]

RFC 3872                      MIB for TRIP                September 2004


        STATUS      current
        DESCRIPTION
            "Indicates the interval that the LS MUST maintain routes
            marked as withdrawn in its database."
        DEFVAL { 10 }
        ::= { tripCfgEntry 11 }

    tripCfgDisableTime OBJECT-TYPE
        SYNTAX      Unsigned32 (1..2147483647)
        UNITS       "Seconds"
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "Indicates the interval that the TRIP module of the
            LS MUST be disabled while routes originated by this
            LS with high sequence numbers can be removed."
        DEFVAL { 180 }
        ::= { tripCfgEntry 12 }

    tripCfgSendReceiveMode OBJECT-TYPE
        SYNTAX TripSendReceiveMode
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The operational mode of the TRIP entity running on this
            system."
        ::= { tripCfgEntry 13 }

    tripCfgStorage OBJECT-TYPE
        SYNTAX       StorageType
        MAX-ACCESS   read-write
        STATUS       current
        DESCRIPTION
           "The storage type for this conceptual row. Conceptual rows
           having the value 'permanent' need not allow write-access
           to any columnar objects in the row."
        DEFVAL { nonVolatile }
        ::= { tripCfgEntry 14 }

 --
 -- TripRouteTypeTable
 --

    tripRouteTypeTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF TripRouteTypeEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION



Zinman, et al.              Standards Track                    [Page 13]

RFC 3872                      MIB for TRIP                September 2004


            "The TRIP peer Route Type table contains one entry per
            supported protocol - address family pair.  The objects in
            this table are volatile and are refreshed after a reboot."
        ::= { tripMIBObjects 2 }

    tripRouteTypeEntry OBJECT-TYPE
        SYNTAX      TripRouteTypeEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "An entry containing information about the route type
            that a particular TRIP entity supports. Each entry
            represents information about either the local or a remote
            LS peer.  The object tripRouteTypePeer is used to
            distinguish this.  In the case of a local LS, the
            address/port information will reflect the values
            configured in tripCfgTable.  In the case of a remote
            peer, the address/port information will reflect the
            values of an entry in the tripPeerTable.

            Implementation need to be aware that if the size of
            tripRouteTypeAddr exceeds 111 sub-IDs, then OIDs of column
            instances in this table will have more than 128 sub-IDs
            and cannot be accessed using SNMPv1, SNMPv2c, or snmpv3."
        INDEX { applIndex,
                tripRouteTypeAddrInetType,
                tripRouteTypeAddr,
                tripRouteTypePort,
                tripRouteTypeProtocolId,
                tripRouteTypeAddrFamilyId }
          ::= { tripRouteTypeTable 1 }

    TripRouteTypeEntry ::= SEQUENCE {
        tripRouteTypeAddrInetType       InetAddressType,
        tripRouteTypeAddr               InetAddress,
        tripRouteTypePort               InetPortNumber,
        tripRouteTypeProtocolId         TripAppProtocol,
        tripRouteTypeAddrFamilyId       TripAddressFamily,
        tripRouteTypePeer               INTEGER
    }

    tripRouteTypeAddrInetType OBJECT-TYPE
        SYNTAX      InetAddressType
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The type of Inet Address of the tripRouteTypeAddr."
        REFERENCE



Zinman, et al.              Standards Track                    [Page 14]

RFC 3872                      MIB for TRIP                September 2004


            "RFC 3291, section 3."
        ::= { tripRouteTypeEntry 1 }

    tripRouteTypeAddr OBJECT-TYPE
        SYNTAX      InetAddress
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The network address of this entry's TRIP peer LS. The
            type of this address is determined by the value of the
            tripRouteTypeAddrInetType object."
        REFERENCE
            "RFC 3291, section 3."
        ::= { tripRouteTypeEntry 2 }

    tripRouteTypePort OBJECT-TYPE
        SYNTAX      InetPortNumber
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The port for the TCP connection between this and
            an associated TRIP peer."
        ::= { tripRouteTypeEntry 3 }

    tripRouteTypeProtocolId OBJECT-TYPE
        SYNTAX      TripAppProtocol
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The object identifier of a protocol that the associated
            peer is using."
        ::= { tripRouteTypeEntry 4 }

    tripRouteTypeAddrFamilyId OBJECT-TYPE
        SYNTAX      TripAddressFamily
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The object identifier of an address family that the
            associated peer belongs to."
        ::= { tripRouteTypeEntry 5 }

    tripRouteTypePeer OBJECT-TYPE
        SYNTAX      INTEGER { local(1), remote(2) }
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "This object identifies whether this entry is



Zinman, et al.              Standards Track                    [Page 15]

RFC 3872                      MIB for TRIP                September 2004


            associated with a 'local' or 'remote' LS peer."
        ::= { tripRouteTypeEntry 6 }

 --
 -- tripSupportedCommunityTable
 --

    tripSupportedCommunityTable   OBJECT-TYPE
        SYNTAX      SEQUENCE OF TripSupportedCommunityEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The list of TRIP communities that this LS supports. A
            TRIP community is a group of destinations that share
            common properties.

            The TRIP Supported Communities entry is used to group
            destinations so that the routing decision can be based
            on the identity of the group."
        REFERENCE
            "RFC 3219, section 5.9"
        ::= { tripMIBObjects 3 }

    tripSupportedCommunityEntry OBJECT-TYPE
        SYNTAX      TripSupportedCommunityEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Entry containing information about a community. A TRIP
            community is a group of destinations that share some
            common property. This attribute is used so that routing
            decisions can be based on the identity of the group."
        INDEX { applIndex, tripSupportedCommunityId }
        ::= { tripSupportedCommunityTable 1 }

    TripSupportedCommunityEntry ::= SEQUENCE {
        tripSupportedCommunityId         TripCommunityId,
        tripSupportedCommunityItad       TripItad,
        tripSupportedCommunityStorage    StorageType,
        tripSupportedCommunityRowStatus  RowStatus
    }

    tripSupportedCommunityId OBJECT-TYPE
        SYNTAX      TripCommunityId
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The identifier of the supported Community."



Zinman, et al.              Standards Track                    [Page 16]

RFC 3872                      MIB for TRIP                September 2004


        ::= { tripSupportedCommunityEntry 1 }

    tripSupportedCommunityItad OBJECT-TYPE
        SYNTAX      TripItad
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The ITAD of the community."
        ::= { tripSupportedCommunityEntry 2 }

   tripSupportedCommunityStorage OBJECT-TYPE
       SYNTAX       StorageType
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION
          "The storage type for this conceptual row.  Conceptual
          rows having the value 'permanent' need not allow write-
          access to any columnar objects in the row. It is not a
          requirement that this storage be non volatile."
       DEFVAL { nonVolatile }
       ::= { tripSupportedCommunityEntry 3 }

    tripSupportedCommunityRowStatus OBJECT-TYPE
        SYNTAX      RowStatus
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The row status of the entry. This object is REQUIRED
            to create or delete rows by a manager. A value for
            tripSupportedCommunityItad MUST be set for row creation
            to be successful. If the instance already exists for a
            particular applIndex, the row create operation will
            fail.

            The value of this object has no effect on whether
            other objects in this conceptual row can be modified."
        ::= { tripSupportedCommunityEntry 4 }

 --
 -- TripPeerTable
 --
    tripPeerTable   OBJECT-TYPE
        SYNTAX      SEQUENCE OF TripPeerEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The TRIP peer table. This table contains one entry per
            TRIP peer, and information about the connection with



Zinman, et al.              Standards Track                    [Page 17]

RFC 3872                      MIB for TRIP                September 2004


            the peer."
        ::= { tripMIBObjects 4 }

    tripPeerEntry OBJECT-TYPE
        SYNTAX      TripPeerEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Entry containing information about the connection with
            a TRIP peer.

            Implementation need to be aware that if the size of
            tripPeerRemoteAddr exceeds 113 sub-IDs, then OIDs of
            column instances in this table will have more than 128
            sub-IDs and cannot be accessed using SNMPv1, SNMPv2c, or
            snmpv3."
        INDEX { applIndex,
                tripPeerRemoteAddrInetType,
                tripPeerRemoteAddr,
                tripPeerRemotePort }
          ::= {tripPeerTable 1}

    TripPeerEntry ::= SEQUENCE {
        tripPeerRemoteAddrInetType            InetAddressType,
        tripPeerRemoteAddr                    InetAddress,
        tripPeerRemotePort                    InetPortNumber,
        tripPeerIdentifier                    TripId,
        tripPeerState                         INTEGER,
        tripPeerAdminStatus                   INTEGER,
        tripPeerNegotiatedVersion             TripProtocolVersion,
        tripPeerSendReceiveMode               TripSendReceiveMode,
        tripPeerRemoteItad                    TripItad,
        tripPeerConnectRetryInterval          Unsigned32,
        tripPeerMaxRetryInterval              Unsigned32,
        tripPeerHoldTime                      Unsigned32,
        tripPeerKeepAlive                     Unsigned32,
        tripPeerHoldTimeConfigured            Unsigned32,
        tripPeerKeepAliveConfigured           Unsigned32,
        tripPeerMaxPurgeTime                  Unsigned32,
        tripPeerDisableTime                   Unsigned32,
        tripPeerLearned                       TruthValue,
        tripPeerStorage                       StorageType,
        tripPeerRowStatus                     RowStatus
    }

    tripPeerRemoteAddrInetType OBJECT-TYPE
        SYNTAX      InetAddressType
        MAX-ACCESS  not-accessible



Zinman, et al.              Standards Track                    [Page 18]

RFC 3872                      MIB for TRIP                September 2004


        STATUS      current
        DESCRIPTION
            "The type of Inet Address of the tripPeerRemoteAddr."
        REFERENCE
            "RFC 3291, section 3."
        ::= { tripPeerEntry 1 }

    tripPeerRemoteAddr OBJECT-TYPE
        SYNTAX      InetAddress
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The IP address of this entry's TRIP peer LS. The type of
            this address is determined by the value of the
            tripPeerRemoteAddrInetType object."
        REFERENCE
            "RFC 3291, section 3."
        ::= { tripPeerEntry 2 }

    tripPeerRemotePort OBJECT-TYPE
        SYNTAX      InetPortNumber
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The remote port for the TCP connection between the
            TRIP peers."
        ::= { tripPeerEntry 3 }

    tripPeerIdentifier OBJECT-TYPE
        SYNTAX      TripId
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "TRIP identifier of the peer."
        ::= { tripPeerEntry 4 }

    tripPeerState OBJECT-TYPE
        SYNTAX      INTEGER {
                        idle(1),
                        connect(2),
                        active(3),
                        openSent(4),
                        openConfirm(5),
                        established(6)
                    }
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION



Zinman, et al.              Standards Track                    [Page 19]

RFC 3872                      MIB for TRIP                September 2004


            "TRIP Peer Finite State Machine state.

            idle(1)       : The initial state. Local LS refuses all
                            incoming connections. No application
                            resources are allocated to processing
                            information about the remote peer.

            connect(2)    : Local LS waiting for a transport
                            protocol connection to be completed to
                            the peer, and is listening for inbound
                            transport connections from the peer.

            active(3)     : Local LS is listening for an inbound
                            connection from the peer, but is not in
                            the process of initiating a connection
                            to the remote peer.

            openSent(4)   : Local LS has sent an OPEN message to its
                            peer and is waiting for an OPEN message
                            from the remote peer.

            openConfirm(5): Local LS has sent an OPEN message to the
                            remote peer, received an OPEN message from
                            the remote peer, and sent a KEEPALIVE
                            message in response to the OPEN. The local
                            LS is now waiting for a KEEPALIVE message
                            or a NOTIFICATION message in response to
                            its OPEN message.

            established(6): LS can exchange UPDATE, NOTIFICATION, and
                            KEEPALIVE messages with its peer."
        ::= { tripPeerEntry 5 }

    tripPeerAdminStatus OBJECT-TYPE
        SYNTAX      INTEGER {
                        up(1),
                        down(2)
                    }
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "This object is used to affect the TRIP connection
            state.

            up(1)   : Allow a connection with the peer LS.

            down(2) : disconnect the connection from the peer LS and
                      do not allow any further connections to this



Zinman, et al.              Standards Track                    [Page 20]

RFC 3872                      MIB for TRIP                September 2004


                      peer.

            If this value is set to down(2) then tripPeerState will
            have the value of idle(1)."
        DEFVAL      { up }
        ::= { tripPeerEntry 6 }

    tripPeerNegotiatedVersion OBJECT-TYPE
        SYNTAX      TripProtocolVersion
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The negotiated version of TRIP running between this
            local entity and this peer."
        ::= { tripPeerEntry 7 }

    tripPeerSendReceiveMode OBJECT-TYPE
        SYNTAX      TripSendReceiveMode
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The operational mode of this peer."
        ::= { tripPeerEntry 8 }

    tripPeerRemoteItad OBJECT-TYPE
        SYNTAX      TripItad
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The Internet Telephony Administrative domain of
            this peer."
        ::= { tripPeerEntry 9 }

    tripPeerConnectRetryInterval OBJECT-TYPE
        SYNTAX      Unsigned32 (0..2147483647)
        UNITS       "Seconds"
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Specifies the initial amount of time that will elapse
            between connection retry. This value SHOULD double
            after each attempt up to the value of
            tripPeerMaxRetryInterval. This value MUST always be less
            than or equal to the value of tripPeerMaxRetryInterval.
            Attempts to set this value higher than the max retry
            will not be allowed."
        DEFVAL      { 120 }
        ::= { tripPeerEntry 10 }



Zinman, et al.              Standards Track                    [Page 21]

RFC 3872                      MIB for TRIP                September 2004


    tripPeerMaxRetryInterval OBJECT-TYPE
        SYNTAX      Unsigned32 (0..2147483647)
        UNITS       "Seconds"
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Specifies the maximum amount of time that will elapse
            between connection retries. Once the value of
            tripPeerConnectRetryInterval has reached this value, no
            more retries will be attempted. Attempts to set this
            value lower than the retry interval SHOULD not be
            allowed."
        DEFVAL      { 360 }
        ::= { tripPeerEntry 11 }

    tripPeerHoldTime OBJECT-TYPE
        SYNTAX      Unsigned32 (1..2147483647)
        UNITS       "Seconds"
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The time interval in seconds for the hold timer that
            is established with the peer. The value of this object
            is the smaller of the values in
            tripPeerHoldTimeConfigured and the hold time received
            in the open message."
        ::= { tripPeerEntry 12 }

    tripPeerKeepAlive OBJECT-TYPE
        SYNTAX      Unsigned32 (1..2147483647)
        UNITS       "Seconds"
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Specifies the amount of time that MUST elapse between
            keep alive messages. This value is negotiated with the
            remote when a connection is established."
        ::= { tripPeerEntry 13 }

    tripPeerHoldTimeConfigured OBJECT-TYPE
        SYNTAX      Unsigned32 (0 | 3..65535)
        UNITS       "Seconds"
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Specifies the maximum time that MAY elapse between the
            receipt of successive keepalive or update message. A value
            of 0 means that keepalive or update messages will not be



Zinman, et al.              Standards Track                    [Page 22]

RFC 3872                      MIB for TRIP                September 2004


            sent."
        DEFVAL { 240 }
        ::= { tripPeerEntry 14 }

    tripPeerKeepAliveConfigured OBJECT-TYPE
        SYNTAX      Unsigned32 (1..2147483647)
        UNITS       "Seconds"
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Specifies the amount of time that MUST elapse between
            keep alive messages."
        DEFVAL { 30 }
        ::= { tripPeerEntry 15 }

    tripPeerMaxPurgeTime OBJECT-TYPE
        SYNTAX      Unsigned32 (1..65535)
        UNITS       "Seconds"
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Indicates the interval that the LS MUST maintain routes
            marked as withdrawn in its database."
        DEFVAL { 10 }
        ::= { tripPeerEntry 16 }

    tripPeerDisableTime OBJECT-TYPE
        SYNTAX      Unsigned32 (1..65535)
        UNITS       "Seconds"
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Indicate the interval that the TRIP module of the remote
            peer LS MUST be disabled while routes originated by the
            local LS with high sequence numbers can be removed."
        DEFVAL { 180 }
        ::= { tripPeerEntry 17 }

    tripPeerLearned OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates whether this entry was learned or
            configured."
        DEFVAL { false }
        ::= { tripPeerEntry 18 }




Zinman, et al.              Standards Track                    [Page 23]

RFC 3872                      MIB for TRIP                September 2004


    tripPeerStorage OBJECT-TYPE
        SYNTAX       StorageType
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
           "The storage type for this conceptual row.  Conceptual
           rows having the value 'permanent' need not allow write-
           access to any columnar objects in the row. It is not a
           requirement that this storage be non volatile."
        DEFVAL { nonVolatile }
        ::= { tripPeerEntry 19 }

    tripPeerRowStatus OBJECT-TYPE
        SYNTAX      RowStatus
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The row status of the entry. This object is REQUIRED to
            create or delete rows remotely by a manager. If the
            instance already exists for a particular applIndex, the
            row create operation will fail.

            The value of this object has no effect on whether
            other objects in this conceptual row can be modified.

            Entries in this table can be learned by the TRIP
            application, or provisioned through this table."
        ::= { tripPeerEntry 20 }

 --
 -- TripPeerStatisticsTable
 --

    tripPeerStatisticsTable   OBJECT-TYPE
        SYNTAX      SEQUENCE OF TripPeerStatisticsEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The TRIP peer stats table. This table contains one
            entry per remote TRIP peer, and statistics related to the
            connection with the remote peer. The objects in this
            table are volatile."
        ::= { tripMIBObjects 5 }

    tripPeerStatisticsEntry OBJECT-TYPE
        SYNTAX      TripPeerStatisticsEntry
        MAX-ACCESS  not-accessible
        STATUS      current



Zinman, et al.              Standards Track                    [Page 24]

RFC 3872                      MIB for TRIP                September 2004


        DESCRIPTION
            "Entry containing information about the connection with
            a TRIP peer."
        AUGMENTS { tripPeerEntry }
          ::= { tripPeerStatisticsTable 1 }

    TripPeerStatisticsEntry ::= SEQUENCE {
        tripPeerInUpdates                   Counter32,
        tripPeerOutUpdates                  Counter32,
        tripPeerInTotalMessages             Counter32,
        tripPeerOutTotalMessages            Counter32,
        tripPeerFsmEstablishedTransitions   Counter32,
        tripPeerFsmEstablishedTime          DateAndTime,
        tripPeerInUpdateElapsedTime         TimeInterval,
        tripPeerStateChangeTime             TimeStamp
    }

     tripPeerInUpdates OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of TRIP update messages received from this
            remote peer since the last restart of this location
            server."
        ::= { tripPeerStatisticsEntry 1 }

    tripPeerOutUpdates OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of TRIP update messages sent to this remote
            peer since the last restart of this LS."
        ::= { tripPeerStatisticsEntry 2 }

    tripPeerInTotalMessages OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The total number of TRIP messages received from the
            remote peer on this connection since the last restart
            of this LS."
        ::= { tripPeerStatisticsEntry 3 }

    tripPeerOutTotalMessages OBJECT-TYPE
        SYNTAX      Counter32



Zinman, et al.              Standards Track                    [Page 25]

RFC 3872                      MIB for TRIP                September 2004


        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The total number of outgoing TRIP messages sent to the
            remote peer since the last restart of this LS."
        ::= { tripPeerStatisticsEntry 4 }

    tripPeerFsmEstablishedTransitions OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of times the remote peer has transitioned
            into the established state since the last restart of this
            LS."
        ::= { tripPeerStatisticsEntry 5 }

    tripPeerFsmEstablishedTime OBJECT-TYPE
        SYNTAX      DateAndTime
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates the time and date that this remote peer entered
            the 'established' state."
        ::= { tripPeerStatisticsEntry 6 }

    tripPeerInUpdateElapsedTime OBJECT-TYPE
        SYNTAX      TimeInterval
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Elapsed time in hundredths of seconds since the last
            TRIP update message was received from this remote peer."
        ::= { tripPeerStatisticsEntry 7 }

    tripPeerStateChangeTime OBJECT-TYPE
        SYNTAX       TimeStamp
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "The value of sysUpTime when the last state change of
            tripPeerState took place."
        ::= { tripPeerStatisticsEntry 8 }

 -- TRIP Received Route Table.  This table contains
 -- all routes from all sources. Each entry consists
 -- of a route and its associated path attributes.




Zinman, et al.              Standards Track                    [Page 26]

RFC 3872                      MIB for TRIP                September 2004


    tripRouteTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF TripRouteEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The TRIP route table containing information about
            reachable routes that are to be added to service by the
            receiving LS. The objects in this table are volatile
            and are refreshed when this LS rediscovers its route
            table."
        ::= { tripMIBObjects 6 }

    tripRouteEntry OBJECT-TYPE
        SYNTAX      TripRouteEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Information about a route to a called destination."
        INDEX { applIndex,
                tripRouteAppProtocol,
                tripRouteAddressFamily,
                tripRouteAddress,
                tripRoutePeer
                }
        ::= { tripRouteTable 1 }

    TripRouteEntry ::= SEQUENCE {
        tripRouteAppProtocol                 TripAppProtocol,
        tripRouteAddressFamily               TripAddressFamily,
        tripRouteAddress                     OCTET STRING,
        tripRoutePeer                        TripId,
        tripRouteTRIBMask                    BITS,
        tripRouteAddressSequenceNumber       Unsigned32,
        tripRouteAddressOriginatorId         TripId,
        tripRouteNextHopServerIAddrType      InetAddressType,
        tripRouteNextHopServer               InetAddress,
        tripRouteNextHopServerPort           InetPortNumber,
        tripRouteNextHopServerItad           TripItad,
        tripRouteMultiExitDisc               Unsigned32,
        tripRouteLocalPref                   Unsigned32,
        tripRouteAdvertisementPath           OCTET STRING,
        tripRouteRoutedPath                  OCTET STRING,
        tripRouteAtomicAggregate             TruthValue,
        tripRouteUnknown                     OCTET STRING,
        tripRouteWithdrawn                   TruthValue,
        tripRouteConverted                   TruthValue,
        tripRouteReceivedTime                TimeStamp
        }



Zinman, et al.              Standards Track                    [Page 27]

RFC 3872                      MIB for TRIP                September 2004


    tripRouteAppProtocol OBJECT-TYPE
        SYNTAX      TripAppProtocol
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The protocol for which this entry of the routing table
            is maintained."
        ::= { tripRouteEntry 1 }

    tripRouteAddressFamily OBJECT-TYPE
        SYNTAX      TripAddressFamily
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Specifies the type of address for the destination
            route."
        ::= { tripRouteEntry 2 }

    tripRouteAddress OBJECT-TYPE
        SYNTAX      OCTET STRING (SIZE(1..105))
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This is the address (prefix) of the family type given
            by Address Family of the destination. It is the prefix
            of addresses reachable from this gateway via the next
            hop server. The SIZE value of 105 has been assigned due
            to the sub identifier of object types length limitation
            as defined in SMIv2."
        REFERENCE
            "RFC 3219, section 5.1.1.1."
        ::= { tripRouteEntry 3 }

    tripRoutePeer OBJECT-TYPE
        SYNTAX      TripId
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The identifier of the peer where the route information
            was learned."
        ::= { tripRouteEntry 4 }

     tripRouteTRIBMask OBJECT-TYPE
        SYNTAX      BITS {
                     adjTribIns(0),
                     extTrib(1),
                     locTrib(2),
                     adjTribOut(3)



Zinman, et al.              Standards Track                    [Page 28]

RFC 3872                      MIB for TRIP                September 2004


                     }
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates which Telephony Routing Information Base (TRIB)
            this entry belongs to. This is
            a bit-map of possible types. If the bit has a value of
            1, then the entry is a member of the corresponding TRIB
            type. If the bit has a value of 0 then the entry is not
            a member of the TRIP type. The various bit positions
            are:

            0    adjTribIns     The entry is of type adj-TRIBs-ins,
                                stores routing information that has
                                been learned from inbound UPDATE
                                messages.
            1    extTrib        The entry is of type ext-TRIB, the
                                best route for a given destination.
            2    locTrib        The entry is of type loc-TRIB contains
                                the local TRIP routing information
                                that the LS has selected.
            3    adjTribOut     The entry is of type adj-TRIBs-out,
                                stores the information that the local
                                LS has selected for advertisement to
                                its external peers."
        REFERENCE
            "RFC 3291, section 3.5."
        ::= { tripRouteEntry 5 }

    tripRouteAddressSequenceNumber OBJECT-TYPE
        SYNTAX      Unsigned32 (1..2147483647)
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates the version of the destination route
            originated by the LS identified by
            tripRouteAddressOriginatorId intra-domain attribute."
        ::= { tripRouteEntry 6 }

    tripRouteAddressOriginatorId OBJECT-TYPE
        SYNTAX      TripId
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "This is an intra-domain attribute indicating the
            internal LS that originated the route into the ITAD."
        ::= { tripRouteEntry 7 }




Zinman, et al.              Standards Track                    [Page 29]

RFC 3872                      MIB for TRIP                September 2004


    tripRouteNextHopServerIAddrType OBJECT-TYPE
        SYNTAX      InetAddressType
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The type of Inet Address of the tripRouteNextHopServer."
        REFERENCE
            "RFC 3291, section 3."
        ::= { tripRouteEntry 8 }

    tripRouteNextHopServer OBJECT-TYPE
        SYNTAX      InetAddress
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates the next hop that messages of a given protocol
            destined for tripRouteAddress SHOULD be sent to. The type
            of this address is determined by the value of the
            tripRouteNextHopServerIAddrType object."
        ::= { tripRouteEntry 9 }

    tripRouteNextHopServerPort OBJECT-TYPE
        SYNTAX      InetPortNumber
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The port of the next hop server that this route
            will use."
        ::= { tripRouteEntry 10 }

    tripRouteNextHopServerItad OBJECT-TYPE
        SYNTAX      TripItad
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates the domain of the next hop."
        ::= { tripRouteEntry 11 }

    tripRouteMultiExitDisc OBJECT-TYPE
        SYNTAX      Unsigned32 (0..4294967295)
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The Multiple Exit Discriminator allows an LS to
            discriminate between, and indicate preference for,
            otherwise similar routes to a neighbouring domain.
            A higher value represents a more preferred routing
            object."



Zinman, et al.              Standards Track                    [Page 30]

RFC 3872                      MIB for TRIP                September 2004


        REFERENCE
            "RFC 3219, section 5.8"
        ::= { tripRouteEntry 12 }

    tripRouteLocalPref OBJECT-TYPE
        SYNTAX      Unsigned32 (0..4294967295)
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicated the local LS's degree of preference for an
            advertised route destination."
        REFERENCE
            "RFC 3219, section 4.3.4.7"
        ::= { tripRouteEntry 13 }

    tripRouteAdvertisementPath OBJECT-TYPE
        SYNTAX      OCTET STRING (SIZE(4..252))
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Identifies the sequence of domains through which this
            advertisement has passed.

            This object is probably best represented as sequence of
            TripItads. For SMI compatibility, though, it is
            represented as an OCTET STRING. This object is a sequence
            of ITADs where each set of 4 octets corresponds to a TRIP
            ITAD in network byte order."
        REFERENCE
            "RFC 3219, section 4.3.4.4"
        ::= { tripRouteEntry 14 }

    tripRouteRoutedPath OBJECT-TYPE
        SYNTAX      OCTET STRING (SIZE(4..252))
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Identifies the ITADs through which messages sent using
            this route would pass. These are a subset of
            tripRouteAdvertisementPath.

            This object is probably best represented as sequence of
            TripItads. For SMI compatibility, though, it is
            represented as OCTET STRING.  This object is a sequence
            of ITADs where each set of 4 octets corresponds to a TRIP
            ITAD in network byte order."
        REFERENCE
            "RFC 3219, section 4.3.4.5"



Zinman, et al.              Standards Track                    [Page 31]

RFC 3872                      MIB for TRIP                September 2004


        ::= { tripRouteEntry 15 }

    tripRouteAtomicAggregate OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates that a route MAY traverse domains not listed
            in tripRouteRoutedPath. If an LS selects the less
            specific route from a set of overlapping routes, then
            this value returns TRUE."
        REFERENCE
            "RFC 3219, section 4.3.4.6"
        ::= { tripRouteEntry 16 }

    tripRouteUnknown OBJECT-TYPE
        SYNTAX      OCTET STRING (SIZE(0..255))
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "This object contains one or more attributes that were not
            understood, and because they were transitive, were dropped
            during aggregation. They take the format of a triple
            <attribute type, attribute length, attribute value>, of
            variable length. If no attributes were dropped, this
            returns an OCTET STRING of size 0."
        REFERENCE
            "RFC 3219, sections 4.3.1, 4.3.2.3"
        ::= { tripRouteEntry 17 }

    tripRouteWithdrawn OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates if this route is to be removed from service
            by the receiving LS."
        ::= { tripRouteEntry 18 }

    tripRouteConverted OBJECT-TYPE
        SYNTAX TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates if this route has been converted to a
            different application protocol than it had originally."
        ::= { tripRouteEntry 19 }




Zinman, et al.              Standards Track                    [Page 32]

RFC 3872                      MIB for TRIP                September 2004


    tripRouteReceivedTime OBJECT-TYPE
        SYNTAX       TimeStamp
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
          "The value of sysUpTime when this route was received."
        ::= { tripRouteEntry 20 }

 --
 -- TRIP Received Route Community Table.
 --

    tripRouteCommunityTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF TripRouteCommunityEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "A table containing a list of TRIP communities associated
            with a route. Each instance of tripRouteTypeEntry that has
            the tripRouteTypePeer object set to remote(2) has an
            instance in the tripRouteTable as a parent. The objects
            in this table are volatile and are refreshed after a
            reboot."
        REFERENCE
            "RFC 3219, section 5.9."
        ::= { tripMIBObjects 7 }

    tripRouteCommunityEntry OBJECT-TYPE
        SYNTAX      TripRouteCommunityEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Information about communities associated with a route.
            An entry with a tripRouteAddress of 00 and a
            tripRoutePeer of 0 refers to the local LS."
        INDEX { applIndex,
                tripRouteAppProtocol,
                tripRouteAddressFamily,
                tripRouteAddress,
                tripRoutePeer,
                tripRouteCommunityId
              }
        ::= { tripRouteCommunityTable 1 }

    TripRouteCommunityEntry ::= SEQUENCE {
         tripRouteCommunityId    TripCommunityId,
         tripRouteCommunityItad  TripItad
         }



Zinman, et al.              Standards Track                    [Page 33]

RFC 3872                      MIB for TRIP                September 2004


    tripRouteCommunityId OBJECT-TYPE
        SYNTAX      TripCommunityId
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The community identifier."
        ::= { tripRouteCommunityEntry 1 }

    tripRouteCommunityItad OBJECT-TYPE
        SYNTAX      TripItad
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The ITAD associated with this community."
        ::= { tripRouteCommunityEntry 2 }

 --
 -- tripItadTopologyTable
 --

    tripItadTopologyTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF TripItadTopologyEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The sequence of link connections between peers within an
            ITAD. The objects in this table are volatile and are
            refreshed after a reboot."
        ::= { tripMIBObjects 8 }

    tripItadTopologyEntry OBJECT-TYPE
        SYNTAX      TripItadTopologyEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Information about a peer of the LS identified by
            tripItadTopologyOrigId."
        INDEX { applIndex, tripItadTopologyOrigId }
        ::= { tripItadTopologyTable 1 }

    TripItadTopologyEntry ::= SEQUENCE {
                tripItadTopologyOrigId    TripId,
                tripItadTopologySeqNum    Unsigned32
            }

    tripItadTopologyOrigId OBJECT-TYPE
        SYNTAX      TripId
        MAX-ACCESS  not-accessible



Zinman, et al.              Standards Track                    [Page 34]

RFC 3872                      MIB for TRIP                September 2004


        STATUS      current
        DESCRIPTION
            "Indicates the internal LS that originated the ITAD
            topology information into the ITAD."
        ::= { tripItadTopologyEntry 1 }

    tripItadTopologySeqNum OBJECT-TYPE
        SYNTAX      Unsigned32 (1..2147483647)
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates the version of the ITAD topology originated
            by the LS identified by tripItadTopologyOrigId."
        ::= { tripItadTopologyEntry 2 }

 --
 -- tripItadTopologyIdTable
 --

    tripItadTopologyIdTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF TripItadTopologyIdEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The list of other LS's within the ITAD domain that the
            LS identified by tripItadTopologyOrigId is currently
            peering. Each instance of tripItadTopologyIdEntry has an
            instance in the tripItadTopologyTable as a parent. The
            objects in this table are volatile and are refreshed
            after a reboot."
        ::= { tripMIBObjects 9 }

    tripItadTopologyIdEntry OBJECT-TYPE
        SYNTAX      TripItadTopologyIdEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Information about a peer to the LS identified by
            tripItadTopologyOrigId."
        INDEX { applIndex,
                tripItadTopologyOrigId,
                tripItadTopologyId }
        ::= { tripItadTopologyIdTable 1 }

    TripItadTopologyIdEntry ::= SEQUENCE {
                tripItadTopologyId            TripId
            }




Zinman, et al.              Standards Track                    [Page 35]

RFC 3872                      MIB for TRIP                September 2004


    tripItadTopologyId OBJECT-TYPE
        SYNTAX      TripId
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The index into this entry. Indicates the other location
            servers within the ITAD domain that this LS identified
            by tripItadTopologyOrigId is currently peering."
        ::= { tripItadTopologyIdEntry 1 }

 --
 -- Notification objects
 --

    tripNotifApplIndex    OBJECT-TYPE
        SYNTAX     Integer32 (1..2147483647)
        MAX-ACCESS accessible-for-notify
        STATUS     current
        DESCRIPTION
             "This object contains the application Index. It is used
             to bind this notification with a specific instance of
             TRIP entity."
        REFERENCE
            "RFC 2788, section 3."
        ::= { tripMIBNotifObjects 1 }

    tripNotifPeerAddrInetType OBJECT-TYPE
        SYNTAX      InetAddressType
        MAX-ACCESS  accessible-for-notify
        STATUS      current
        DESCRIPTION
            "The type of Inet Address of the tripNotifPeerAddr."
        REFERENCE
            "RFC 3291, section 3."
        ::= { tripMIBNotifObjects 2 }

    tripNotifPeerAddr OBJECT-TYPE
        SYNTAX      InetAddress
        MAX-ACCESS  accessible-for-notify
        STATUS      current
        DESCRIPTION
            "The IP address of this entry's TRIP peer LS. This object
            contains the value of tripPeerRemoteAddr. The type of this
            address is determined by the value of the
            tripNotifPeerAddrInetType object."
        REFERENCE
            "RFC 3291, section 3."
        ::= { tripMIBNotifObjects 3 }



Zinman, et al.              Standards Track                    [Page 36]

RFC 3872                      MIB for TRIP                September 2004


    tripNotifPeerErrCode OBJECT-TYPE
        SYNTAX      INTEGER {
                        messageHeader(1),
                        openMessage(2),
                        updateMessage(3),
                        holdTimerExpired(4),
                        finiteStateMachine(5),
                        cease(6),
                        tripNotification(7)
                    }
        MAX-ACCESS  accessible-for-notify
        STATUS      current
        DESCRIPTION
            "Notification message of TRIP error. The meaning of this
            value is applicable to the following functions:

            messageHeader(1)
             - All errors detected while processing the TRIP message
               header.

            openMessage(2)
             - All errors detected while processing the OPEN message.

            updateMessage(3)
             - All errors detected while processing the UPDATE
               message.

            holdTimerExpired(4)
             - A notification generated when the hold timer expires.

            finiteStateMachine(5)
             - All errors detected by the TRIP Finite State Machine.

            cease(6)
             - Any fatal error condition that the rest of the values
               do not cover.

            tripNotification(7)
             - Any error encountered while sending a notification
               message."
       ::= { tripMIBNotifObjects 4 }

    tripNotifPeerErrSubcode OBJECT-TYPE
        SYNTAX      Unsigned32 (1..2147483647)
        MAX-ACCESS  accessible-for-notify
        STATUS      current
        DESCRIPTION
            "The sub error code associated with error code. The



Zinman, et al.              Standards Track                    [Page 37]

RFC 3872                      MIB for TRIP                September 2004


            meaning of this value is dependent on the value of
            tripNotifPeerErrCode.

            Message Header (1) Error Subcodes:
            1 - Bad Message Length.
            2 - Bad Message Type.

            OPEN Message (2) Error Subcodes:
            1 - Unsupported Version Number.
            2 - Bad Peer ITAD.
            3 - Bad TRIP Identifier.
            4 - Unsupported Optional Parameter.
            5 - Unacceptable Hold Time.
            6 - Unsupported Capability.
            7 - Capability Mismatch.

            UPDATE Message (3) Error Subcodes:
            1 - Malformed Attribute List.
            2 - Unrecognized Well-known Attribute.
            3 - Missing Well-known Mandatory Attribute.
            4 - Attribute Flags Error.
            5 - Attribute Length Error.
            6 - Invalid Attribute."
       ::= { tripMIBNotifObjects 5 }

 --
 -- Notifications
 --
    tripConnectionEstablished NOTIFICATION-TYPE
        OBJECTS { tripNotifApplIndex,
                  tripNotifPeerAddrInetType,
                  tripNotifPeerAddr
                }
        STATUS  current
        DESCRIPTION
            "The TRIP Connection Established event is generated when
            the TRIP finite state machine enters the ESTABLISHED
            state."
        ::= { tripMIBNotifications 1 }

    tripConnectionDropped NOTIFICATION-TYPE
        OBJECTS { tripNotifApplIndex,
                  tripNotifPeerAddrInetType,
                  tripNotifPeerAddr
                }
        STATUS  current
        DESCRIPTION
            "The TRIP Connection Dropped event is generated when the



Zinman, et al.              Standards Track                    [Page 38]

RFC 3872                      MIB for TRIP                September 2004


            TRIP finite state machine leaves the ESTABLISHED state."
        ::= { tripMIBNotifications 2 }

    tripFSM NOTIFICATION-TYPE
        OBJECTS { tripNotifApplIndex,
                  tripNotifPeerAddrInetType,
                  tripNotifPeerAddr,
                  tripNotifPeerErrCode,
                  tripNotifPeerErrSubcode,
                  tripPeerState
                }
        STATUS  current
        DESCRIPTION
            "The trip FSM Event is generated when any error is
            detected by the TRIP Finite State Machine."
        ::= { tripMIBNotifications 3 }

    tripOpenMessageError NOTIFICATION-TYPE
        OBJECTS { tripNotifApplIndex,
                  tripNotifPeerAddrInetType,
                  tripNotifPeerAddr,
                  tripNotifPeerErrCode,
                  tripNotifPeerErrSubcode,
                  tripPeerState
                }
        STATUS  current
        DESCRIPTION
            "Errors detected while processing the OPEN message."
        ::= { tripMIBNotifications 4 }

    tripUpdateMessageError NOTIFICATION-TYPE
        OBJECTS { tripNotifApplIndex,
                  tripNotifPeerAddrInetType,
                  tripNotifPeerAddr,
                  tripNotifPeerErrCode,
                  tripNotifPeerErrSubcode,
                  tripPeerState
                }
        STATUS  current
        DESCRIPTION
            "Errors detected while processing the UPDATE message."
        ::= { tripMIBNotifications 5 }

    tripHoldTimerExpired NOTIFICATION-TYPE
        OBJECTS { tripNotifApplIndex,
                  tripNotifPeerAddrInetType,
                  tripNotifPeerAddr,
                  tripNotifPeerErrCode,



Zinman, et al.              Standards Track                    [Page 39]

RFC 3872                      MIB for TRIP                September 2004


                  tripNotifPeerErrSubcode,
                  tripPeerState
                }
        STATUS  current
        DESCRIPTION
            "The system does not receive successive messages within
            the period specified by the negotiated Hold Time."
        ::= { tripMIBNotifications 6 }

    tripConnectionCollision NOTIFICATION-TYPE
        OBJECTS { tripNotifApplIndex }
        STATUS  current
        DESCRIPTION
            "A pair of LSs tried to simultaneously to establish a
            transport connection to each other."
        ::= { tripMIBNotifications 7 }

    tripCease NOTIFICATION-TYPE
        OBJECTS { tripNotifApplIndex,
                  tripNotifPeerAddrInetType,
                  tripNotifPeerAddr,
                  tripNotifPeerErrCode,
                  tripNotifPeerErrSubcode,
                  tripPeerState
                }
        STATUS  current
        DESCRIPTION
            "A TRIP peer MAY choose at any given time to close its TRIP
            connection by sending this notification message. However,
            the Cease notification message MUST NOT be used when a
            fatal error occurs."

        ::= { tripMIBNotifications 8 }

    tripNotificationErr NOTIFICATION-TYPE
        OBJECTS { tripNotifApplIndex }
        STATUS  current
        DESCRIPTION
            "Generated if there is an error detected in a TRIP
            notification message sent with another cause. Note that
            the TRIP notification referred to in this object is not
            an SNMP notification, it is a specific message described
            in the TRIP specification."
        REFERENCE
            "RFC 3219, section  6.4."
        ::= { tripMIBNotifications 9 }

    --



Zinman, et al.              Standards Track                    [Page 40]

RFC 3872                      MIB for TRIP                September 2004


    -- Compliance Statements
    --

    tripMIBFullCompliance MODULE-COMPLIANCE
        STATUS     current
        DESCRIPTION
             "The compliance statement for TRIP entities that
             implement this MIB module in read-write mode, such
             that it can be used for both monitoring and configuring
             the TRIP entity.

             There is one INDEX object that cannot be represented in
             the form of OBJECT clauses in SMIv2, but for which there
             is a compliance requirement, expressed in OBJECT clause
             form in this description:

             -- OBJECT      tripRouteTypeAddrInetType
             -- SYNTAX      InetAddressType (ipv4(1), ipv6(2),
             --                              ipv4z(3), ipv6z(4))
             -- DESCRIPTION
             --     This MIB requires support for global and
             --     non-global ipv4 and ipv6 addresses.
             --
             -- OBJECT      tripRouteTypeAddr
             -- SYNTAX      InetAddress (SIZE (4 | 8 | 16 | 20))
             -- DESCRIPTION
             --     This MIB requires support for global and
             --     non-global IPv4 and IPv6 addresses.
             --
             "

        MODULE -- this module
             MANDATORY-GROUPS { tripConfigGroup,
                                tripPeerTableConfigGroup,
                                tripRouteGroup,
                                tripItadTopologyGroup,
                                tripPeerTableStatsGroup }

        GROUP tripNotificationGroup
        DESCRIPTION
            "This group is OPTIONAL. A TRIP entity can choose not to
            send any notifications. If this group is implemented,
            the tripNotifObjectGroup MUST also be implemented."

        GROUP tripNotifObjectGroup
        DESCRIPTION
            "This group is OPTIONAL. A TRIP entity can choose not to
            send any notifications. If this group is implemented,



Zinman, et al.              Standards Track                    [Page 41]

RFC 3872                      MIB for TRIP                September 2004


            the tripNotificationGroup MUST also be implemented."

        OBJECT       tripSupportedCommunityRowStatus
        SYNTAX       RowStatus { active(1) }
        WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
        DESCRIPTION
           "Support for createAndWait and notInService is not
           required."

        OBJECT       tripPeerRowStatus
        SYNTAX       RowStatus { active(1) }
        WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
        DESCRIPTION
           "Support for createAndWait and notInService is not
           required."

        MODULE NETWORK-SERVICES-MIB
             MANDATORY-GROUPS { applRFC2788Group }

        ::= { tripMIBCompliances 1 }
    tripMIBReadOnlyCompliance MODULE-COMPLIANCE
        STATUS     current
        DESCRIPTION
             "The compliance statement for TRIP entities that
             implement this MIB module in read only mode. Such TRIP
             entities can then only be monitored, but not be
             configured via this MIB module.

             In read-only mode, the manager will not be able to add,
             remove or modify rows to any table, however the TRIP
             application may modify, remove or add rows to a table.

             There is one INDEX object that cannot be represented in
             the form of OBJECT clauses in SMIv2, but for which there
             is a compliance requirement, expressed in OBJECT clause
             form in this description:

             -- OBJECT      tripRouteTypeAddrInetType
             -- SYNTAX      InetAddressType (ipv4(1), ipv6(2),
             --                              ipv4z(3), ipv6z(4))
             -- DESCRIPTION
             --     This MIB requires support for global and
             --     non-global ipv4 and ipv6 addresses.
             --
             -- OBJECT      tripRouteTypeAddr
             -- SYNTAX      InetAddress (SIZE (4 | 8 | 16 | 20))
             -- DESCRIPTION
             --     This MIB requires support for global and



Zinman, et al.              Standards Track                    [Page 42]

RFC 3872                      MIB for TRIP                September 2004


             --     non-global IPv4 and IPv6 addresses.
             --
             "

        MODULE -- this module
             MANDATORY-GROUPS { tripConfigGroup,
                                tripPeerTableConfigGroup,
                                tripRouteGroup,
                                tripItadTopologyGroup,
                                tripPeerTableStatsGroup }

        GROUP tripNotificationGroup
        DESCRIPTION
            "This group is OPTIONAL. A TRIP entity can choose not to
            send any notifications. If this group is implemented,
            the tripNotifObjectGroup MUST also be implemented."

        GROUP tripNotifObjectGroup
        DESCRIPTION
            "This group is OPTIONAL. A TRIP entity can choose not to
            send any notifications. If this group is implemented,
            the tripNotificationGroup MUST also be implemented."
        OBJECT       tripCfgItad
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripCfgAdminStatus
        MIN-ACCESS   not-accessible
        DESCRIPTION
           "Object is not needed when implemented in read-only mode."

        OBJECT       tripCfgPort
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripCfgMinItadOriginationInterval
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripCfgMinRouteAdvertisementInterval
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripCfgMaxPurgeTime



Zinman, et al.              Standards Track                    [Page 43]

RFC 3872                      MIB for TRIP                September 2004


        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripCfgDisableTime
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripCfgStorage
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripSupportedCommunityItad
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripSupportedCommunityStorage
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT      tripSupportedCommunityRowStatus
        SYNTAX      RowStatus { active(1) }
        MIN-ACCESS  read-only
        DESCRIPTION
           "Write access is not required, and active is the only
           status that needs to be supported."

        OBJECT       tripPeerAdminStatus
        MIN-ACCESS   not-accessible
        DESCRIPTION
           "Object is not needed when implemented in read-only mode."

        OBJECT       tripPeerConnectRetryInterval
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripPeerMaxRetryInterval
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripPeerHoldTimeConfigured
        MIN-ACCESS   read-only



Zinman, et al.              Standards Track                    [Page 44]

RFC 3872                      MIB for TRIP                September 2004


        DESCRIPTION
           "Write access is not required."

        OBJECT       tripPeerKeepAliveConfigured
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripPeerMaxPurgeTime
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripPeerDisableTime
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT       tripPeerStorage
        MIN-ACCESS   read-only
        DESCRIPTION
           "Write access is not required."

        OBJECT      tripPeerRowStatus
        SYNTAX      RowStatus { active(1) }
        MIN-ACCESS  read-only
        DESCRIPTION
           "Write access is not required, and active is the only
           status that needs to be supported."
        MODULE NETWORK-SERVICES-MIB
             MANDATORY-GROUPS { applRFC2788Group }

        ::= { tripMIBCompliances 2 }

 --
 -- Object and event conformance groups
 --

    tripConfigGroup OBJECT-GROUP
        OBJECTS {
            tripCfgProtocolVersion,
            tripCfgItad,
            tripCfgIdentifier,
            tripCfgOperStatus,
            tripCfgAdminStatus,
            tripCfgAddrIAddrType,
            tripCfgAddr,
            tripCfgPort,



Zinman, et al.              Standards Track                    [Page 45]

RFC 3872                      MIB for TRIP                September 2004


            tripCfgMinItadOriginationInterval,
            tripCfgMinRouteAdvertisementInterval,
            tripCfgMaxPurgeTime,
            tripCfgDisableTime,
            tripCfgSendReceiveMode,
            tripCfgStorage,
            tripSupportedCommunityItad,
            tripSupportedCommunityStorage,
            tripRouteTypePeer,
            tripSupportedCommunityRowStatus
        }
        STATUS current
        DESCRIPTION
            "The global objects for configuring trip."
        ::= { tripMIBGroups 1 }

    tripPeerTableConfigGroup OBJECT-GROUP
        OBJECTS {
            tripPeerIdentifier,
            tripPeerState,
            tripPeerAdminStatus,
            tripPeerNegotiatedVersion,
            tripPeerSendReceiveMode,
            tripPeerRemoteItad,
            tripPeerConnectRetryInterval,
            tripPeerMaxRetryInterval,
            tripPeerHoldTime,
            tripPeerKeepAlive,
            tripPeerHoldTimeConfigured,
            tripPeerKeepAliveConfigured,
            tripPeerMaxPurgeTime,
            tripPeerDisableTime,
            tripPeerLearned,
            tripPeerStorage,
            tripPeerRowStatus
            }

        STATUS current
        DESCRIPTION
            "The global objects for configuring the TRIP peer
            table."
        ::= { tripMIBGroups 2 }

    tripPeerTableStatsGroup OBJECT-GROUP
        OBJECTS {
            tripPeerInUpdates,
            tripPeerOutUpdates,
            tripPeerInTotalMessages,



Zinman, et al.              Standards Track                    [Page 46]

RFC 3872                      MIB for TRIP                September 2004


            tripPeerOutTotalMessages,
            tripPeerFsmEstablishedTransitions,
            tripPeerFsmEstablishedTime,
            tripPeerInUpdateElapsedTime,
            tripPeerStateChangeTime
            }
        STATUS current
        DESCRIPTION
            "The global statistics the TRIP peer table."
        ::= { tripMIBGroups 3 }

    tripRouteGroup OBJECT-GROUP
        OBJECTS {
            tripRouteTRIBMask,
            tripRouteAddressSequenceNumber,
            tripRouteAddressOriginatorId,
            tripRouteNextHopServerIAddrType,
            tripRouteNextHopServer,
            tripRouteNextHopServerPort,
            tripRouteNextHopServerItad,
            tripRouteMultiExitDisc,
            tripRouteLocalPref,
            tripRouteAdvertisementPath,
            tripRouteRoutedPath,
            tripRouteAtomicAggregate,
            tripRouteUnknown,
            tripRouteWithdrawn,
            tripRouteConverted,
            tripRouteReceivedTime,
            tripRouteCommunityItad
            }

        STATUS current
        DESCRIPTION
            "The global objects for configuring route attribute."
        ::= { tripMIBGroups 4 }
    tripItadTopologyGroup OBJECT-GROUP
        OBJECTS {
            tripItadTopologySeqNum,
            tripItadTopologyId
            }
        STATUS current
        DESCRIPTION
            "The objects that define the TRIP ITAD topology."
        ::= { tripMIBGroups 5 }

    tripNotificationGroup NOTIFICATION-GROUP
        NOTIFICATIONS {



Zinman, et al.              Standards Track                    [Page 47]

RFC 3872                      MIB for TRIP                September 2004


            tripConnectionEstablished,
            tripConnectionDropped,
            tripFSM,
            tripOpenMessageError,
            tripUpdateMessageError,
            tripHoldTimerExpired,
            tripConnectionCollision,
            tripCease,
            tripNotificationErr
        }
        STATUS  current
        DESCRIPTION
             "A collection of notifications defined for TRIP."
        ::= { tripMIBGroups 6 }

    tripNotifObjectGroup OBJECT-GROUP
        OBJECTS {
            tripNotifApplIndex,
            tripNotifPeerAddrInetType,
            tripNotifPeerAddr,
            tripNotifPeerErrCode,
            tripNotifPeerErrSubcode
            }
        STATUS current
        DESCRIPTION
            "The collection of objects that specify information for
            TRIP notifications."
        ::= { tripMIBGroups 7 }

END

7.  Security Considerations

   The managed objects in this MIB module contain sensitive information
   since, collectively, they allow tracing and influencing of
   connections in TRIP devices and provide information of their
   connection characteristics.  As such, improper manipulation of the
   objects represented by this MIB module MAY result in denial of
   service to a large number of available routes.

   There are a number of management objects defined in this MIB module
   that have a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects MAY be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These objects include:





Zinman, et al.              Standards Track                    [Page 48]

RFC 3872                      MIB for TRIP                September 2004


      tripCfgItad:
      Improper setting of tripCfgItad value can make all peer
      connections drop and not be re-established.

      tripCfgAdminStatus:
      Improper setting of tripCfgAdminStatus from up to down will cause
      the TRIP Location Server stop processing TRIP messages.

      tripCfgPort:
      Improper setting of tripCfgPort can cause the failure of a peer
      establishing a connection.

      tripCfgMinItadOriginationInterval,
      tripCfgMinRouteAdvertisementInterval:
      Improper configuration of these values MAY adversely affect local
      and global convergence of the routes advertised by this TRIP
      Location Server.

      tripPeerAdminStatus:
      Improper setting of tripPeerAdminStatus from up to down can cause
      significant disruption of the connectivity to the destination via
      the applicable remote TRIP Location Server peer.

      tripPeerConnectRetryInterval,tripPeerMaxRetryInterval:
      Improper configuration of these values can cause connections to be
      disrupted for extremely long time periods when otherwise they
      would be restored in a relatively short period of time.

      tripPeerHoldTimeConfigured, tripPeerKeepAliveConfigured:
      Improper configuration of these value can make TRIP peer sessions
      more fragile and less resilient to denial of service attacks.

   There are a number of managed objects in this MIB module that contain
   sensitive information regarding the operation of a network.  For
   example, a TRIP Location Server peer's local and remote addresses
   might be sensitive for ISPs who want to keep interface addresses on
   TRIP Location Server confidential so as to prevent TRIP Location
   Server addresses used for a denial of service attack or address
   spoofing.

   Therefore, it is thus important to control even GET access to these
   objects and possibly to even encrypt the values of these object when
   sending them over the network via SNMP.  Not all versions of SNMP
   provide features for such a secure environment.







Zinman, et al.              Standards Track                    [Page 49]

RFC 3872                      MIB for TRIP                September 2004


   SNMPv1 by itself is not a secure environment.  Even if the network
   itself is secure (for example by using IPSec), even then, there is no
   control as to who on the secure network is allowed to access and
   GET/SET (read/change/create/delete) the objects in this MIB module.

   It is RECOMMENDED that the implementers consider the security
   features as provided by the SNMPv3 framework (see [RFC3410], section
   8), including full support for the SNMPv3 cryptographic mechanisms
   (for authentication and privacy).

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

8.  References

8.1.  Normative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Textual
             Conventions for SMIv2", STD 58, RFC 2579, April 1999.

   [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
             "Conformance Statements for SMIv2", STD 58, RFC 2580, April
             1999.

   [RFC2788] Freed, N. and S. Kille, "Network Services Monitoring MIB",
             RFC 2788, March 2000.

   [RFC3219] Rosenberg, J., Salama, H., and M. Squire, "Telephony
             Routing over IP (TRIP)", RFC 3219, January 2002.

   [RFC3291] Daniele, M., Haberman, B., Routhier, S., and J.
             Schoenwaelder, "Textual Conventions for Internet Network
             Addresses", RFC 3291, May 2002.

   [RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
             "Structure of Management Information Version 2 (SMIv2)",
             STD 58, RFC 2578, April 1999.






Zinman, et al.              Standards Track                    [Page 50]

RFC 3872                      MIB for TRIP                September 2004


8.2.  Informative References

   [RFC1657] Willis, S., Burruss, J., and J. Chu, Ed., "Definitions of
             Managed Objects for the Fourth Version of the Border
             Gateway Protocol (BGP-4) using SMIv2", RFC 1657, July 1994.

   [RFC1771] Rekhter, Y. and T. Li, "Border Gateway Protocol 4 (BGP-4)",
             RFC 1771, March 1995.

   [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
             "Introduction and Applicability Statements for Internet-
             Standard Management Framework", RFC 3410, December 2002.

9.  Acknowledgments

   The authors wish to thank Bert Wijnen, Dan Romascanu, and Jonathan
   Rosenberg for their insightful comments and suggestions.

   Thanks to Kevin Lingle for his invaluable comments, help with MIB
   things and great ideas.































Zinman, et al.              Standards Track                    [Page 51]

RFC 3872                      MIB for TRIP                September 2004


10.  Authors' Addresses

   David Zinman
   Editor
   265 Ridley Blvd
   Toronto ON  M5M 4N8
   Canada

   Phone: +1 416 433 4298
   EMail: dzinman@rogers.com


   David Walker
   Sedna Wireless Inc.
   495 March Road, Suite 500
   Ottawa, ON K2K 3G1
   Canada

   Phone: +1 613 878 8142
   EMail: david.walker@sedna-wireless.com


   Jianping Jiang
   Syndesis Limited
   30 Fulton Way
   Richmond Hill, ON L4B 1J5
   Canada

   Phone: +1 905 886-7818 x2515
   EMail: jjiang@syndesis.com





















Zinman, et al.              Standards Track                    [Page 52]

RFC 3872                      MIB for TRIP                September 2004


11. Full Copyright Statement

   Copyright (C) The Internet Society (2004).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/S HE
   REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE
   INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR
   IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the IETF's procedures with respect to rights in IETF Documents can
   be found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at ietf-
   ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.







Zinman, et al.              Standards Track                    [Page 53]