💾 Archived View for gmi.noulin.net › rfc › rfc2189.gmi captured on 2024-05-26 at 17:07:25. Gemini links have been rewritten to link to archived content

View Raw

More Information

⬅️ Previous capture (2023-01-29)

-=-=-=-=-=-=-

Keywords: Inter-Domain-Protocol, IDMR







Network Working Group                                       A. Ballardie
Request for Comments: 2189                                    Consultant
Category: Experimental                                    September 1997



           Core Based Trees (CBT version 2) Multicast Routing

                      -- Protocol Specification --


Status of this Memo

   This memo defines an Experimental Protocol for the Internet
   community.  It does not specify an Internet standard of any kind.
   Discussion and suggestions for improvement are requested.
   Distribution of this memo is unlimited.

Abstract

   This document describes the Core Based Tree (CBT version 2) network
   layer multicast routing protocol. CBT builds a shared multicast
   distribution tree per group, and is suited to inter- and intra-domain
   multicast routing.

   CBT may use a separate multicast routing table, or it may use that of
   underlying unicast routing, to establish paths between senders and
   receivers. The CBT architecture is described in [1].

   This document is progressing through the IDMR working group of the
   IETF.  CBT related documents include [1, 5, 6]. For all IDMR-related
   documents, see http://www.cs.ucl.ac.uk/ietf/idmr.

TABLE OF CONTENTS

  1. Changes Since Previous version............................. 2
  2. Introduction & Terminology................................. 3
  3. CBT Functional Overview.................................... 3
  4. CBT Protocol Specificiation Details........................ 6
     4.1 CBT HELLO Protocol..................................... 6
         4.1.1 Sending HELLOs................................... 7
         4.1.2 Receiving HELLOs................................. 7
     4.2 JOIN_REQUEST Processing................................ 8
         4.2.1 Sending JOIN_REQUESTs............................ 8
         4.2.2 Receiving JOIN_REQUESTs.......................... 8
     4.3 JOIN_ACK Processing.................................... 9
         4.3.1 Sending JOIN_ACKs................................ 9
         4.3.2 Receiving JOIN_ACKs.............................. 9



Ballardie                     Experimental                      [Page 1]

RFC 2189              CBTv2 Protocl Specification         September 1997


     4.4 QUIT_NOTIFICATION Processing........................... 10
         4.4.1 Sending QUIT_NOTIFICATIONs....................... 10
         4.4.2 Receiving QUIT_NOTIFICATIONs..................... 10
     4.5 CBT ECHO_REQUEST Processing............................ 11
         4.5.1 Sending ECHO_REQUESTs............................ 11
         4.5.2 Receiving ECHO_REQUESTs.......................... 12
     4.6 ECHO_REPLY Processing.................................. 12
         4.6.1 Sending ECHO_REPLYs.............................. 12
         4.6.2 Receiving ECHO_REPLYs............................ 12
     4.7 FLUSH_TREE Processing.................................. 13
         4.7.1 Sending FLUSH_TREE Messages...................... 13
         4.7.2 Receiving FLUSH_TREE Messages.................... 13
  5. Non-Member Sending......................................... 13
  6. Timers and Default Values.................................. 13
  7. CBT Packet Formats and Message Types....................... 14
     7.1 CBT Common Control Packet Header....................... 14
     7.2 HELLO Packet Format.................................... 15
     7.3 JOIN_REQUEST Packet Format............................. 16
     7.4 JOIN_ACK Packet Format................................. 16
     7.5 QUIT_NOTIFICATION Packet Format........................ 17
     7.6 ECHO_REQUEST Packet Format............................. 18
     7.7 ECHO_REPLY Packet Format............................... 18
     7.8 FLUSH_TREE Packet Format............................... 19
  8. Core Router Discovery...................................... 19
     8.1  "Bootstrap" Mechanism Overview........................ 20
     8.2  Bootstrap Message Format.............................. 21
     8.3  Candidate Core Advertisement Message Format........... 21
  9. Interoperability Issues.................................... 21
  10.  Security Considerations.................................. 21
  Acknowledgements.............................................. 22
  References.................................................... 22
  Author Information............................................ 23

1.  Changes from CBT version 1

   This version of the CBT protocol specification differs significantly
   from the previous version. Consequently, this version represents
   version 2 of the CBT protocol.  CBT version 2 is not, and was not,
   intended to be backwards compatible with version 1; we do not expect
   this to cause extensive compatibility problems because we do not
   believe CBT is at all widely deployed at this stage. However, any
   future versions of CBT can be expected to be backwards compatible
   with this version.








Ballardie                     Experimental                      [Page 2]

RFC 2189              CBTv2 Protocl Specification         September 1997


   The most significant changes to version 2 compared to version 1
   include:

   o new LAN mechanisms, including the incorporation of an HELLO
     protocol.

   o new simplified packet formats, with the definition of a common CBT
     control packet header.

   o each group shared tree has only one active core router.

     This specification revision is a complete re-write of the previous
     revision.

2.  Introduction & Terminology

   In CBT, a "core router" (or just "core") is a router which acts as a
   "meeting point" between a sender and group receivers. The term
   "rendezvous point (RP)" is used equivalently in some contexts [2]. A
   core router need not be configured to know it is a core router.

   A router that is part of a CBT distribution tree is known as an "on-
   tree" router. An on-tree router maintains active state for the group.

   We refer to a broadcast interface as any interface that supports
   multicast transmission.

   An "upstream" interface (or router) is one which is on the path
   towards the group's core router with respect to this interface (or
   router). A "downstream" interface (or router) is one which is on the
   path away from the group's core router with respect to this interface
   (or router).

   Other terminology is introduced in its context throughout the text.

3.  CBT Functional Overview

   The CBT protocol is designed to build and maintain a shared multicast
   distribution tree that spans only those networks and links leading to
   interested receivers.

   To achieve this, a host first expresses its interest in joining a
   group by multicasting an IGMP host membership report [3] across its
   attached link. On receiving this report, a local CBT aware router
   invokes the tree joining process (unless it has already) by
   generating a JOIN_REQUEST message, which is sent to the next hop on
   the path towards the group's core router (how the local router
   discovers which core to join is discussed in section 8). This join



Ballardie                     Experimental                      [Page 3]

RFC 2189              CBTv2 Protocl Specification         September 1997


   message must be explicitly acknowledged (JOIN_ACK) either by the core
   router itself, or by another router that is on the path between the
   sending router and the core, which itself has already successfully
   joined the tree.

   The join message sets up transient join state in the routers it
   traverses, and this state consists of <group, incoming interface,
   outgoing interface>. "Incoming interface" and "outgoing interface"
   may be "previous hop" and "next hop", respectively, if the
   corresponding links do not support multicast transmission. "Previous
   hop" is taken from the incoming control packet's IP source address,
   and "next hop" is gleaned from the routing table - the next hop to
   the specified core address. This transient state eventually times out
   unless it is "confirmed" with a join acknowledgement (JOIN_ACK) from
   upstream. The JOIN_ACK traverses the reverse path of the
   corresponding join message, which is possible due to the presence of
   the transient join state. Once the acknowledgement reaches the router
   that originated the join message, the new receiver can receive
   traffic sent to the group.

   Loops cannot be created in a CBT tree because a) there is only one
   active core per group, and b) tree building/maintenance scenarios
   which may lead to the creation of tree loops are avoided.  For
   example, if a router's upstream neighbour becomes unreachable, the
   router immediately "flushes" all of its downstream branches, allowing
   them to individually rejoin if necessary.  Transient unicast loops do
   not pose a threat because a new join message that loops back on
   itself will never get acknowledged, and thus eventually times out.

   The state created in routers by the sending or receiving of a
   JOIN_ACK is bi-directional - data can flow either way along a tree
   "branch", and the state is group specific - it consists of the group
   address and a list of local interfaces over which join messages for
   the group have previously been acknowledged. There is no concept of
   "incoming" or "outgoing" interfaces, though it is necessary to be
   able to distinguish the upstream interface from any downstream
   interfaces. In CBT, these interfaces are known as the "parent" and
   "child" interfaces, respectively. A router is not considered "on-
   tree" until it has received a JOIN_ACK for a previously sent
   JOIN_REQUEST.

   With regards to the information contained in the multicast forwarding
   cache, on link types not supporting native multicast transmission an
   on-tree router must store the address of a parent and any children.
   On links supporting multicast however, parent and any child
   information is represented with local interface addresses (or similar
   identifying information, such as an interface "index") over which the
   parent or child is reachable.



Ballardie                     Experimental                      [Page 4]

RFC 2189              CBTv2 Protocl Specification         September 1997


   Data from non-member senders must be encapsulated (IP-in-IP) by the
   first-hop router, and is unicast to the group's core router.
   Consequently, no group state is required in the network between the
   first hop router and the group's core. On arriving at the core
   router, the data packet's outer encapsulating header is removed and
   the packet is disemminated over the group shared tree as described
   below.

   When a multicast data packet arrives at a router, the router uses the
   group address as an index into the multicast forwarding cache. A copy
   of the incoming multicast data packet is forwarded over each
   interface (or to each address) listed in the entry except the
   incoming interface.

   Each router that comprises a CBT multicast tree, except the core
   router, is responsible for maintaining its upstream link, provided it
   has interested downstream receivers, i.e. the child interface list is
   not NULL. A child interface is one over which a member host is
   directly attached, or one over which a downstream on-tree router is
   attached.  This "tree maintenance" is achieved by each downstream
   router periodically sending a CBT "keepalive" message (ECHO_REQUEST)
   to its upstream neighbour, i.e. its parent router on the tree. One
   keepalive message is sent to represent entries with the same parent,
   thereby improving scalability on links which are shared by many
   groups.  On multicast capable links, a keepalive is multicast to the
   "all-cbt-routers" group (IANA assigned as 224.0.0.15); this has a
   suppressing effect on any other router for which the link is its
   parent link.  If a parent link does not support multicast
   transmission, keepalives are unicast.

   The receipt of a keepalive message over a valid child interface
   prompts a response (ECHO_REPLY), which is either unicast or
   multicast, as appropriate.  The ECHO_REPLY message carries a list of
   groups for which the corresponding interface is a child interface.

   It cannot be assumed all of the routers on a multi-access link have a
   uniform view of unicast routing; this is particularly the case when a
   multi-access link spans two or more unicast routing domains. This
   could lead to multiple upstream tree branches being formed (an error
   condition) unless steps are taken to ensure all routers on the link
   agree which is the upstream router for a particular group. CBT
   routers attached to a multi-access link participate in an explicit
   election mechanism that elects a single router, the designated router
   (DR), as the link's upstream router for all groups. Since the DR
   might not be the link's best next-hop for a particular core router,
   this may result in join messages being re-directed back across a
   multi-access link. If this happens, the re-directed join message is
   unicast across the link by the DR to the best next-hop, thereby



Ballardie                     Experimental                      [Page 5]

RFC 2189              CBTv2 Protocl Specification         September 1997


   preventing a looping scenario. This re-direction only ever applies to
   join messages.  Whilst this is suboptimal for join messages, which
   are generated infrequently, multicast data never traverses a link
   more than once (either natively, or encapsulated).

   In all but the exception case described above, all CBT control
   messages are multicast over multicast supporting links to the "all-
   cbt- routers" group, with IP TTL 1. The IP source address of CBT
   control messages is the outgoing interface of the sending router. The
   IP destination address of CBT control messages is either the "all-
   cbt- routers" group address, or a unicast address, as appropriate.
   All the necessary addressing information is obtained by on-tree
   routers as part of tree set up.

   If CBT is implemented over a tunnelled topology, when sending a CBT
   control packet over a tunnel interface, the sending router uses as
   the packet's IP source address the local tunnel end point address,
   and the remote tunnel end point address as the packet's IP
   destination address.

4.  Protocol Specification Details

   Details of the CBT protocol are presented in the context of a single
   router implementation.

4.1.  CBT HELLO Protocol

   The HELLO protocol is used to elect a designated router (DR) on
   broadcast-type links. It is also used to elect a designated border
   router (BR) when interconnecting a CBT domain with other domains (see
   [5]). Alternatively, the designated BR may be elected as a matter of
   local policy.

   A router represents its status as a link's DR by setting the DR-flag
   on that interface; a DR flag is associated with each of a router's
   broadcast interfaces. This flag can only assume one of two values:
   TRUE or FALSE. By default, this flag is FALSE.

   A network manager can preference a router's DR eligibility by
   optionally configuring an HELLO preference, which is included in the
   router's HELLO messages.  Valid configuration values range from 1 to
   254 (decimal), 1 representing the "most eligible" value. In the
   absence of explicit configuration, a router assumes the default HELLO
   preference value of 255. The elected DR uses HELLO preference zero
   (0) in HELLO advertisements, irrespective of any configured
   preference.  The DR continues to use preference zero for as long as
   it is running.




Ballardie                     Experimental                      [Page 6]

RFC 2189              CBTv2 Protocl Specification         September 1997


   HELLO messages are multicast periodically to the all-cbt-routers
   group, 224.0.0.15, using IP TTL 1. The advertisement period is
   [HELLO_INTERVAL] seconds.

   HELLO messages have a suppressing effect on those routers which would
   advertise a "lesser preference" in their HELLO messages; a router
   resets its [HELLO_INTERVAL] if the received HELLO is "better" than
   its own. Thus, in steady state, the HELLO protocol incurs very little
   traffic overhead.

   The DR election winner is that which advertises the lowest HELLO
   preference, or the lowest-addressed in the event of a tie.

   The situation where two or more routers attached to the same
   broadcast link areadvertising HELLO preference 0 should never arise.
   However, should this situation arise, all but the lowest addressed
   zero advertising router relinquishes its claim as DR immediately by
   unsetting the DR flag on the corresponding interface. The
   relinquishing router(s) subsequently advertise their previously used
   preference value in HELLO advertisements.

4.1.1.  Sending HELLOs

   When a router starts up, it multicasts two HELLO messages over each
   of its broadcast interfaces in successsion. The DR flag is initially
   unset (FALSE) on each broadcast interface.  This avoids the situation
   in which each router on a multi-access subnet believes it is the DR,
   thus preventing the multiple forwarding of join-requests should they
   arrive during this start up period.  If no "better" HELLO message is
   received after HOLDTIME seconds, the router assumes the role of DR on
   the corresponding interface.

   A router sends an HELLO message whenever its [HELLO_INTERVAL]
   expires.  Whenever a router sends an HELLO message, it resets its
   hello timer.

4.1.2.  Receiving HELLOs

   A router does not respond to an HELLO message if the received HELLO
   is "better" than its own, or equally preferenced but lower addressed.

   A router must respond to an HELLO message if that received is lesser
   preferenced (or equally preferenced but higher addressed) than would
   be sent by this router over the same interface. This response is sent
   on expiry of an interval timer which is set between zero (0) and
   [HOLDTIME] seconds when the lesser preferenced HELLO message is
   received.




Ballardie                     Experimental                      [Page 7]

RFC 2189              CBTv2 Protocl Specification         September 1997


4.2.  JOIN_REQUEST Processing

   A JOIN_REQUEST is the CBT control message used to register a member
   host's interest in joining the distribution tree for the group.

4.2.1.  Sending JOIN_REQUESTs

   A JOIN_REQUEST can only ever be originated by a leaf router, i.e. a
   router with directly attached member hosts. This join message is sent
   hop-by-hop towards the core router for the group (see section 8).
   The originating router caches <group, NULL, upstream interface> state
   for each join it originates. This state is known as "transient join
   state".  The absence of a "downstream interface" (NULL) indicates
   that this router is the join message originator, and is therefore
   responsible for any retransmissions of this message if a response is
   not received within [RTX_INTERVAL].  It is an error if no response is
   received after [JOIN_TIMEOUT] seconds.  If this error condition
   occurs, the joining process may be re-invoked by the receipt of the
   next IGMP host membership report from a locally attached member host.

   Note that if the interface over which a JOIN_REQUEST is to be sent
   supports multicast, the JOIN_REQUEST is multicast to the all-cbt-
   routers group, using IP TTL 1.  If the link does not support
   multicast, the JOIN_REQUEST is unicast to the next hop on the unicast
   path to the group's core.

4.2.2.  Receiving JOIN_REQUESTs

   On broadcast links, JOIN_REQUESTs which are multicast may only be
   forwarded by the link's DR. Other routers attached to the link may
   process the join (see below). JOIN_REQUESTs which are multicast over
   a point-to-point link are only processed by the router on the link
   which does not have a local interface corresponding to the join's
   network layer (IP) source address. Unicast JOIN_REQUESTs may only be
   processed by the router which has a local interface corresponding to
   the join's network layer (IP) destination address.

   With regard to forwarding a received JOIN_REQUEST, if the receiving
   router is not on-tree for the group, and is not the group's core
   router, and has not already forwarded a join for the same group, the
   join is forwarded to the next hop on the path towards the core. The
   join is multicast, or unicast, according to whether the outgoing
   interface supports multicast.  The router caches the following
   information with respect to the forwarded join: <group, downstream
   interface, upstream interface>. Subsequent JOIN_REQUESTs received for
   the same group are cached until this router has received a JOIN_ACK
   for the previously sent join, at which time any cached joins can also
   be acknowledged.



Ballardie                     Experimental                      [Page 8]

RFC 2189              CBTv2 Protocl Specification         September 1997


   If this transient join state is not "confirmed" with a join
   acknowledgement (JOIN_ACK) message from upstream, the state is timed
   out after [TRANSIENT_TIMEOUT] seconds.

   If the receiving router is the group's core router, the join is
   "terminated" and acknowledged by means of a JOIN_ACK. Similarly, if
   the router is on-tree and the JOIN_REQUEST arrives over an interface
   that is not the upstream interface for the group, the join is
   acknowledged.

   If a JOIN_REQUEST for the same group is scheduled to be sent over the
   corresponding interface (i.e. awaiting a timer expiry), the
   JOIN_REQUEST is unscheduled.

   If this router has a cache-deletion-timer [CACHE_DEL_TIMER] running
   on the arrival interface for the group specified in a multicast join,
   the timer is cancelled.

4.3.  JOIN_ACK Processing

   A JOIN_ACK is the mechanism by which an interface is added to a
   router's multicast forwarding cache; thus, the interface becomes part
   of the group distribution tree.

4.3.1.  Sending JOIN_ACKs

   The JOIN_ACK is sent over the same interface as the corresponding
   JOIN_REQUEST was received. The sending of the acknowledgement causes
   the router to add the interface to its child interface list in its
   forwarding cache for the group, if it is not already.

   A JOIN_ACK is multicast or unicast, according to whether the outgoing
   interface supports multicast transmission or not.

4.3.2.  Receiving JOIN_ACKs

   The group and arrival interface must be matched to a <group, ....,
   upstream interface> from the router's cached transient state. If no
   match is found, the JOIN_ACK is discarded.  If a match is found, a
   CBT forwarding cache entry for the group is created, with "upstream
   interface" marked as the group's parent interface.

   If "downstream interface" in the cached transient state is NULL, the
   JOIN_ACK has reached the originator of the corresponding
   JOIN_REQUEST; the JOIN_ACK is not forwarded downstream.  If
   "downstream interface" is non-NULL, a JOIN_ACK for the group is sent





Ballardie                     Experimental                      [Page 9]

RFC 2189              CBTv2 Protocl Specification         September 1997


   over the "downstream interface" (multicast or unicast, accordingly).
   This interface is installed in the child interface list of the
   group's forwarding cache entry.

   Once transient state has been confirmed by transferring it to the
   forwarding cache, the transient state is deleted.

4.4.  QUIT_NOTIFICATION Processing

   A CBT tree is "pruned" in the direction downstream-to-upstream
   whenever a CBT router's child interface list for a group becomes
   NULL.

4.4.1.  Sending QUIT_NOTIFICATIONs

   A QUIT_NOTIFICATION is sent to a router's parent router on the tree
   whenever the router's child interface list becomes NULL. If the link
   over which the quit is to be sent supports multicast transmission, if
   the sending router is the link's DR the quit is unicast, otherwise it
   is multicast.

   A QUIT_NOTIFICATION is not acknowledged; once sent, all information
   pertaining to the group it represents is deleted from the forwarding
   cache immediately.

   To help ensure consistency between a child and parent router given
   the potential for loss of a QUIT_NOTIFICATION, a total of [MAX_RTX]
   QUIT_NOTIFICATIONs are sent, each HOLDTIME seconds after the previous
   one.

   The sending of a quit (the first) also invokes the sending of a
   FLUSH_TREE message over each downstream interface for the
   corresponding group.

4.4.2.  Receiving QUIT_NOTIFICATIONs

   The group reported in the QUIT_NOTIFICATION must be matched with a
   forwarding cache entry. If no match is found, the QUIT_NOTIFICATION
   is ignored and discarded.  If a match is found, if the arrival
   interface is a valid child interface in the group entry, how the
   router proceeds depends on whether the QUIT_NOTIFICATION was
   multicast or unicast.

   If the QUIT_NOTIFICATION was unicast, the corresponding child
   interface is deleted from the group's forwarding cache entry, and no
   further processing is required.





Ballardie                     Experimental                     [Page 10]

RFC 2189              CBTv2 Protocl Specification         September 1997


   If the QUIT_NOTIFICATION was multicast, and the arrival interface is
   a valid child interface for the specified group, the router sets a
   cache-deletion-timer [CACHE_DEL_TIMER].

   Because this router might be acting as a parent router for multiple
   downstream routers attached to the arrival link, [CACHE_DEL_TIMER]
   interval gives those routers that did not send the  QUIT_NOTIFICA-
   TION, but received it over their parent interface, the opportunity to
   ensure that the parent router does not remove the link from its child
   interface list.  Therefore, on receipt of a multicast
   QUIT_NOTIFICATION over a parent interface, a receiving router
   schedules a JOIN_REQUEST for the group for sending at a random
   interval between 0 (zero) and HOLDTIME seconds.  If a multicast
   JOIN_REQUEST is received over the corresponding interface (parent)
   for the same group before this router sends its own scheduled
   JOIN_REQUEST, it unschedules the multicasting of its own
   JOIN_REQUEST.

4.5.  ECHO_REQUEST Processing

   The ECHO_REQUEST message allows a child to monitor reachability to
   its parent router for a group (or range of groups if the parent
   router is the parent for multiple groups). Group information is not
   carried in ECHO_REQUEST messages.

4.5.1.  Sending ECHO_REQUESTs

   Whenever a router creates a forwarding cache entry due to the receipt
   of a JOIN_ACK, the router begins the periodic sending of ECHO_REQUEST
   messages over its parent interface. The ECHO_REQUEST is multicast to
   the "all-cbt-routers" group over multicast-capable interfaces, unless
   the sending router is the DR on the interface over which the
   ECHO_REQUEST is being sent, in which case it is unicast (as is the
   corresponding ECHO_REPLY).

   ECHO_REQUEST messages are sent at [ECHO_INTERVAL] second intervals.

   Whenever an ECHO_REQUEST is sent, [ECHO_INTERVAL] is reset.

   If no response is forthcoming, any groups present on the parent
   interface will eventually expire [GROUP_EXPIRE_TIME]. This results in
   the sending of a QUIT_NOTIFICATION upstream, and sends a FLUSH_TREE
   message downstream for each group for which the upstream interface
   was the parent interface.







Ballardie                     Experimental                     [Page 11]

RFC 2189              CBTv2 Protocl Specification         September 1997


4.5.2.  Receiving ECHO_REQUESTs

   If an ECHO_REQUEST is received over any valid child interface, the
   receiving router schedules an ECHO_REPLY message for sending over the
   same interface; the scheduled interval is between 0 (zero) and
   HOLDTIME seconds. This message is multicast to the "all-cbt-routers"
   group over multicast-capable interfaces, and unicast otherwise.

   If a multicast ECHO_REQUEST message arrives via any valid parent
   interface, the router resets its [ECHO_INTERVAL] timer for that
   upstream interface, thereby suppressing the sending of its own
   ECHO_REQUEST over that upstream interface.

4.6.  ECHO_REPLY Processing

   ECHO_REPLY messages allow a child to monitor the reachability of its
   parent, and help ensure the group state information is consistent
   between them.

4.6.1.  Sending ECHO_REPLY messages

   An ECHO_REPLY message is sent in response to receiving an
   ECHO_REQUEST message, provided the ECHO_REQUEST is received over any
   one of this router's valid child interfaces. An ECHO_REPLY reports
   all groups for which the link is its child.

   ECHO_REPLY messages are unicast or multicast, as appropriate.

4.6.2.  Receiving ECHO_REPLY messages

   An ECHO_REPLY message must be received via a valid parent interface.

   For each group reported in an ECHO_REPLY, the downstream router
   attempts to match the group with one in its forwarding cache for
   which the arrival interface is the group's parent interface. For each
   successful match, the entry is "refreshed". If however, after
   [GROUP_EXPIRE_TIME] seconds a group has not been "refreshed", a
   QUIT_NOTIFICATION is sent upstream, and a FLUSH_TREE message is sent
   downstream, for the group.

   If this router has directly attached members for any of the flushed
   groups, the receipt of an IGMP host membership report for any of
   those groups will prompt this router to rejoin the corresponding
   tree(s).







Ballardie                     Experimental                     [Page 12]

RFC 2189              CBTv2 Protocl Specification         September 1997


4.7.  FLUSH_TREE Processing

   The FLUSH_TREE (flush) message is the mechanism by which a router
   invokes the tearing down of all its downstream branches for a
   particular group. The flush message is multicast to the "all-cbt-
   routers" group when sent over multicast-capable interfaces, and
   unicast otherwise.

4.7.1.  Sending FLUSH_TREE messages

   A FLUSH_TREE message is sent over each downstream (child) interface
   when a router has lost reachability with its parent router for the
   group (detected via ECHO_REQUEST and ECHO_REPLY messages). All group
   state is removed from an interface over which a flush message is
   sent.  A flush can specify a single group, or all groups
   (INADDR_ANY).

4.7.2.  Receiving FLUSH_TREE messages

   A FLUSH_TREE message must be received over the parent interface for
   the specified group, otherwise the message is discarded.

   The flush message must be forwarded over each child interface for the
   specified group.

   Once the flush message has been forwarded, all state for the group is
   removed from the router's forwarding cache.

5.  Non-Member Sending

   Data can be sent to a CBT tree by a sender not attached to the group
   tree.  The sending host originates native multicast data, which is
   promiscuously received by a local router, which must be CBT capable.
   It is assumed the local CBT router knows about the relevant <core,
   group> mapping, and thus can encapsulate (IP-in-IP) the data packet
   and unicast it to the corresponding core router. On arriving at the
   core router, the data packet is decapsulated and disemminated over
   the group tree in the manner already described.

6.  Timers and Default Values

   This section provides a summary of the timers described above,
   together with their recommended default values. Other values may be
   configured; if so, the values used should be consistent across all
   CBT routers attached to the same network.

   o    [HELLO_INTERVAL]: the interval between sending an HELLO message.
        Default: 60 seconds.



Ballardie                     Experimental                     [Page 13]

RFC 2189              CBTv2 Protocl Specification         September 1997


   o    [HELLO_PREFERENCE]: Default: 255.

   o    [HOLDTIME]: generic response interval. Default: 3 seconds.

   o    [MAX_RTX]: default maximum number of retransmissions. Default 3.

   o    [RTX_INTERVAL]: message retransmission time. Default: 5 seconds.

   o    [JOIN_TIMEOUT]: raise exception due to tree join failure.
        Default: 3.5 times [RTX_INTERVAL].

   o    [TRANSIENT_TIMEOUT]: delete (unconfirmed) transient state.
        Default: (1.5*RTX_INTERVAL) seconds.

   o    [CACHE_DEL_TIMER]: remove child interface from forwarding cache.
        Default: (1.5*HOLDTIME) seconds.

   o    [GROUP_EXPIRE_TIME]: time to send a QUIT_NOTIFICATION to our
        non-responding parent.  Default: (1.5*ECHO_INTERVAL).

   o    [ECHO_INTERVAL]: interval between sending ECHO_REQUEST to parent
        routers.  Default: 60 seconds.

   o    [EXPECTED_REPLY_TIME]: consider parent unreachable. Default: 70
        seconds.

7. CBT Packet Formats and Message Types

   CBT control packets are encapsulated in IP. CBT has been assigned IP
   protocol number 7 by IANA [4].

7.1.  CBT Common Control Packet Header

   All CBT control messages have a common fixed length header.

       0               1               2               3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  vers | type  |  addr len     |         checksum              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


                  Figure 1. CBT Common Control Packet Header


   This CBT specification is version 2.





Ballardie                     Experimental                     [Page 14]

RFC 2189              CBTv2 Protocl Specification         September 1997


   CBT packet types are:

   o    type 0: HELLO

   o    type 1: JOIN_REQUEST

   o    type 2: JOIN_ACK

   o    type 3: QUIT_NOTIFICATION

   o    type 4: ECHO_REQUEST

   o    type 5: ECHO_REPLY

   o    type 6: FLUSH_TREE

   o    type 7: Bootstrap Message (optional)

   o    type 8: Candidate Core Advertisement (optional)


   o    Addr Length: address length in bytes of unicast or multicast
        addresses carried in the control packet.

   o    Checksum: the 16-bit one's complement of the one's complement
        sum of the entire CBT control packet.

7.2.  HELLO Packet Format

    0               1               2               3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                    CBT Control Packet Header                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Preference   |  option type  |  option len   |  option value |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                     Figure 2. HELLO Packet Format


   HELLO Packet Field Definitions:

   o    preference: sender's HELLO preference.

   o    option type: the type of option present in the "option value"
        field.  One option type is currently defined: option type 0
        (zero) = BR_HELLO; option value 0 (zero); option length 0
        (zero). This option type is used with HELLO messages sent by a



Ballardie                     Experimental                     [Page 15]

RFC 2189              CBTv2 Protocl Specification         September 1997


        border router (BR) as part of designated BR election (see [5]).

   o    option len: length of the "option value" field in bytes.

   o    option value: variable length field carrying the option value.

7.3.  JOIN_REQUEST Packet Format


       0               1               2               3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    CBT Control Packet Header                  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          group address                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          target router                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        originating router                     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  option type  |  option len   |        option value           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                     Figure 3. JOIN_REQUEST Packet Format


      JOIN_REQUEST Field Definitions

   o    group address: multicast group address of the group being joined.
        For a "wildcard" join (see [5]), this field contains the value of
        INADDR_ANY.

   o    target router: target (core) router for the group.

   o    originating router: router that originated this JOIN_REQUEST.

   o    option type, option len, option value: see HELLO packet format,
        section 7.2.

7.4.  JOIN_ACK Packet Format

      JOIN_ACK Field Definitions

   o    group address: multicast group address of the group being joined.

   o    target router: router (DR) that originated the corresponding
        JOIN_REQUEST.




Ballardie                     Experimental                     [Page 16]

RFC 2189              CBTv2 Protocl Specification         September 1997


       0               1               2               3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    CBT Control Packet Header                  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          group address                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                           target router                       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  option type  |  option len   |         option value          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                       Figure 4. JOIN_ACK Packet Format
   o    option type, option len, option value: see HELLO packet format,
        section 7.2.

7.5.  QUIT_NOTIFICATION Packet Format


       0               1               2               3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    CBT Control Packet Header                  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          group address                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    originating child router                   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                  Figure 5. QUIT_NOTIFICATION Packet Format


      QUIT_NOTIFICATION Field Definitions

   o    group address: multicast group address of the group being joined.

   o    originating child router: address of the router that
        originates the QUIT_NOTIFICATION.













Ballardie                     Experimental                     [Page 17]

RFC 2189              CBTv2 Protocl Specification         September 1997


7.6.  ECHO_REQUEST Packet Format


       0               1               2               3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    CBT Control Packet Header                  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    originating child router                   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                     Figure 6. ECHO_REQUEST Packet Format


      ECHO_REQUEST Field Definitions

   o    originating child router: address of the router that
        originates the ECHO_REQUEST.


7.7.  ECHO_REPLY Packet Format


       0               1               2               3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    CBT Control Packet Header                  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    originating parent router                  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                       group address #1                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                       group address #2                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                           ......                              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                       group address #n                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                      Figure 7. ECHO_REPLY Packet Format


      ECHO_REPLY Field Definitions

   o    oringinating parent router: address of the router originating
        this ECHO_REPLY.

   o    group address: a list of multicast group addresses for which



Ballardie                     Experimental                     [Page 18]

RFC 2189              CBTv2 Protocl Specification         September 1997


        this router considers itself a parent router w.r.t. the link
        over which this message is sent.

7.8.  FLUSH_TREE Packet Format


       0               1               2               3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    CBT Control Packet Header                  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                         group address                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                           ......                              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                       group address #n                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                      Figure 8. FLUSH_TREE Packet Format


      FLUSH_TREE Field Definitions

   o    group address(es): multicast group address(es) of the group(s)
        being "flushed".

8.  Core Router Discovery

   There are two available options for CBTv2 core discovery; the
   "bootstrap" mechanism (as currently specified with the PIM sparse
   mode protocol [2]) is applicable only to intra-domain core discovery,
   and allows for a "plug & play" type operation with minimal
   configuration.  The disadvantage of the bootstrap mechanism is that
   it is much more difficult to affect the shape, and thus optimality,
   of the resulting distribution tree.  Also, to be applicable, all CBT
   routers within a domain must implement the bootstrap mechanism.

   The other option is to manually configure leaf routers with <core,
   group> mappings (note: leaf routers only); this imposes a degree of
   administrative burden - the mapping for a particular group must be
   coordinated across all leaf routers to ensure consistency. Hence,
   this method does not scale particularly well. However, it is likely
   that "better" trees will result from this method, and it is also the
   only available option for inter-domain core discovery currently
   available.






Ballardie                     Experimental                     [Page 19]

RFC 2189              CBTv2 Protocl Specification         September 1997


8.1.  "Bootstrap" Mechanism Overview

   It is unlikely that the bootstrap mechanism will be appended to a
   well-known network layer protocol, such as IGMP [3], though this
   would facilitate its ubiquitous (intra-domain) deployment. Therefore,
   each multicast routing protocol requiring the bootstrap mechanism
   must implement it as part of the multicast routing protocol itself.

   A summary of the operation of the bootstrap mechanism follows
   (details are provided in [7]). It is assumed that all routers within
   the domain implement the "bootstrap" protocol, or at least forward
   bootstrap protocol messages.

   A subset of the domain's routers are configured to be CBT candidate
   core routers. Each candidate core router periodically (default every
   60 secs) advertises itself to the domain's Bootstrap Router (BSR),
   using  "Core Advertisement" messages.  The BSR is itself elected
   dynamically from all (or participating) routers in the domain.  The
   domain's elected BSR collects "Core Advertisement" messages from
   candidate core routers and periodically advertises a candidate core
   set (CC-set) to each other router in the domain, using traditional
   hop- by-hop unicast forwarding. The BSR uses "Bootstrap Messages" to
   advertise the CC-set. Together, "Core Advertisements" and "Bootstrap
   Messages" comprise the "bootstrap" protocol.

   When a router receives an IGMP host membership report from one of its
   directly attached hosts, the local router uses a hash function on the
   reported group address, the result of which is used as an index into
   the CC-set. This is how local routers discover which core to use for
   a particular group.

   Note the hash function is specifically tailored such that a small
   number of consecutive groups always hash to the same core.
   Furthermore, bootstrap messages can carry a "group mask", potentially
   limiting a CC-set to a particular range of groups. This can help
   reduce traffic concentration at the core.

   If a BSR detects a particular core as being unreachable (it has not
   announced its availability within some period), it deletes the
   relevant core from the CC-set sent in its next bootstrap message.
   This is how a local router discovers a group's core is unreachable;
   the router must re-hash for each affected group and join the new core
   after removing the old state. The removal of the "old" state follows
   the sending of a QUIT_NOTIFICATION upstream, and a FLUSH_TREE message
   downstream.






Ballardie                     Experimental                     [Page 20]

RFC 2189              CBTv2 Protocl Specification         September 1997


8.2.  Bootstrap Message Format

     0               1               2               3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             CBT common control packet header                  |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |      For full Bootstrap Message specification, see [7]        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                   Figure 9. Bootstrap Message Format


8.3.  Candidate Core Advertisement Message Format


     0               1               2               3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |              CBT common control packet header                 |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   For full Candidate Core Adv. Message specification, see [7] |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

         Figure 10. Candidate Core Advertisement Message Format

9.  Interoperability Issues

   Interoperability between CBT and DVMRP is specified in [5].

   Interoperability with other multicast protocols will be fully
   specified as the need arises.

10.  Security Considerations

   Security considerations are not addressed in this memo.

   Whilst multicast security is a topic of ongoing research, multicast
   applications (users) nevertheless have the ability to take advantage
   of security services such as encryption or/and authentication
   provided such services are supported by the applications.

   RFCs 1949 and 2093/2094 discuss different ways of distributing
   multicast key material, which can result in the provision of network
   layer access control to a multicast distribution tree.

   [9] offers a synopsis of multicast security threats and proposes some
   possible counter measures.



Ballardie                     Experimental                     [Page 21]

RFC 2189              CBTv2 Protocl Specification         September 1997


   Beyond these, little published work exists on the topic of multicast
   security.

Acknowledgements

   Special thanks goes to Paul Francis, NTT Japan, for the original
   brainstorming sessions that brought about this work.

   The emergence of CBTv2 owes much to Clay Shields and his work on
   Ordered CBT (OCBT) [8]. Clay identified and proved several failure
   modes of CBT as it was specified with multiple cores, and also
   suggested using an unreliable quit mechanism, which appears in this
   specification as the QUIT_NOTIFICATION. Clay has also provided more
   general constructive comments on the CBT architecture and
   specification.

   Others that have contributed to the progress of CBT include Ken
   Carlberg, Eric Crawley, Jon Crowcroft, Mark Handley, Ahmed Helmy,
   Nitin Jain, Alan O'Neill, Steven Ostrowsksi, Radia Perlman, Scott
   Reeve, Benny Rodrig, Martin Tatham, Dave Thaler, Sue Thompson, Paul
   White, and other participants of the IETF IDMR working group.

   Thanks also to 3Com Corporation and British Telecom Plc for funding
   this work.

References

   [1] Core Based Trees (CBT) Multicast Routing Architecture; A.
   Ballardie; RFC 2201, September 1997.

   [2] Protocol Independent Multicast (PIM) Sparse Mode/Dense Mode; D.
   Estrin et al; ftp://netweb.usc.edu/pim   Working drafts, 1996.

   [3] Internet Group Management Protocol, version 2 (IGMPv2); W.
   Fenner; ftp://ds.internic.net/internet-drafts/draft-ietf-idmr-igmp-
   v2-**.txt.  Working draft, 1996.

   [4] Reynolds, J., and J. Postel, "Assigned Numbers", STD 2, RFC 1700,
   October 1994.

   [5] CBT Border Router Specification for Interconnecting a CBT Stub
   Region to a DVMRP Backbone; A. Ballardie;
   ftp://ds.internic.net/internet-drafts/draft-ietf-idmr-cbt-dm-
   interop-**.txt.  Working draft,  March 1997.

   [6] Ballardie, A., "Scalable Multicast Key Distribution", RFC 1949,
   July 1996.




Ballardie                     Experimental                     [Page 22]

RFC 2189              CBTv2 Protocl Specification         September 1997


   [7] A Dynamic Bootstrap Mechanism for Rendezvous-based Multicast
   Routing; D. Estrin et al.; Technical Report;
   ftp://catarina.usc.edu/pim

   [8] The Ordered Core Based Tree Protocol; C. Shields and J.J. Garcia-
   Luna-Aceves; In Proceedings of IEEE Infocom'97, Kobe, Japan, April
   1997;
   http://www.cse.ucsc.edu/research/ccrg/publications/infocomm97ocbt.ps.gz

   [9]  Multicast-Specific Security Threats and Counter-Measures; A.
   Ballardie and J. Crowcroft; In Proceedings "Symposium on Network and
   Distributed System Security", February 1995, pp.2-16.



Author Information:

   Tony Ballardie,
   Research Consultant

   EMail: ABallardie@acm.org






























Ballardie                     Experimental                     [Page 23]