💾 Archived View for uscoffings.net › retro-computing › components › storage › DTC%207287 › dtc-7287-… captured on 2024-05-12 at 18:04:21.

View Raw

More Information

⬅️ Previous capture (2023-01-29)

-=-=-=-=-=-=-


P C - D I S K     The Harddisk Information Database
DCI AG, Germany                      www.pc-disk.de


D T C - 7 2 8 7    DTC

Interface      RLL / ST506
Encoding       RLL 2/7
Bus type       ISA             16 Bit
Add.Port       -
Cache/Buffer        0 /     0 KB
Mirror/Duplex  NO  / NO
Disk array     -
Max. HDD       2        Interleave     1:1
     Head/Cyl. 16 / 2048
Sector size    -
Sectors/Track  -
Max.FDD        2
    Type       1.2,1.44,360KB,720KB
   Device type
Transf.rate       0.938 MB/s HOST
                  0.000 MB/s LUN sync
                  0.000 MB/s     async
Busmaster      NO
DMA            NO
BIOS           YES
Address
Debug          -
I/O Port
Interrupt
Ext.connect.   -
Length         FULL
Op.system
Driver         -
Compatible     -
Ceriticates
Warranty         
P C - D I S K     The Harddisk Information Database
DCI AG, Germany                      www.pc-disk.de

                        L   A   Y   O   U   T

DATA TECH. DTC-7287



 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄJ4ÄJ3ÄJ2ÄJ1ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
 ³ÚÄÄÄ¿                   ²² ²² ²² ²²              ÚÄW4  ³
 ³ÀÄÄÄJ5                  ²² ²² ²² ²²             W7ÄÙ   ³
 ³                        ²² ²² ²² ²²                    ³
 ³                 ÚÄ¿          ²² ²²                    ³
 ³                 ÀÄW6         ²² ²²                    ³
 ³                              ²² ²²                    ³
 ³                                      W5ÂÂW3           ³
 ³                                       ÀÁÅÙ            ³
 ³                                         W2    W9ÂÂW8  ³
 ³                                                ÀÅÁÙ   ³
 ³                                                 W10   ³
 ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿         ÚÄ¿                 ÚÄÙ
                         ÀÁÁÁÁÁÁÁÁÁÙ ÀÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÙ




P C - D I S K     The Harddisk Information Database
DCI AG, Germany                      www.pc-disk.de

                      J   U   M   P   E   R   S

DATA TECH. DTC-7287

 Jumpeer W1
 ==========
 The 7287 does not contain Jumper W1


 Jumper W2 & W3
 ==============
 W2 and W3 jumpers are for the I/O port addresses


 W2 and W3 not installed = Primary port address (1F0-to 1F7,
                           3F2 to 3F7)
 W2 and W3 installed     = Secondary port address (170
                           to 177, 372 to 377)


 Jumper W4 Initial Data Rate Control
 ===================================
 Jumper W4 controls the power-up data transfer rate for
 floppy drive.

 W4 installed     = 250KHz
 W4 not installed = 500 KHz (default)


 Jumper W5 Firmware/Hardware Drive Select
 ========================================
 Two modes of drive selection are supported. In the hardware
 drive select mode, the drive number is driven directly to
 the drive interface. In the firmware drive select mode, the
 drive number is intercepted by the controller firmware.

 W5 unstalled     = Hardware Select Mode (default)
 W5 not installed = Firmware Select Mode


 Jumper W6 Auto-deselect mode
 ============================
 This jumper is used to control the drive selcet light
 (LED). Removal of this jumper will cause the drive light
 (LED) to remain brightly illuminated whenever power is on.

 W6 installed     = Auto-deselect enabled
 W6 not installed = Auto-deselect disabled


 Jumper W7 Floppy Precompensation Control
 ========================================
 Two modes of precompensation for the floppy drive are
 supported on this controller.

 W7 installed = precompensation at 125ns
 W7 removed   = precompensation is scaled by the data rate
                floppy drive is running on (125ns for
                500KHz, 208ns for 300KHz, and 250ns for
                250KHz).

 W7 is not installed at the factory.


 Jumper W8
 =========
 Jumper W8 is for internal use only and must be installed
 (closed) for the controller to operate.


 Jumper W9 BIOS Prom address
 ===========================
 The 7287 requires 16K of memory. This block can be
 addressed beginning at C800:0000 or D8000:0000.

 W9 installed     = D800:0000 to DC00:0000
 W9 not installed = C800:0000 to CC00:0000 (default)


 Jumper W10 BIOS Prom enable
 ===========================
 W10 installed     = Enable the on-board BIOS PROM (default)
 W10 not installed = Disable the on-board BIOS PROM


P C - D I S K     The Harddisk Information Database
DCI AG, Germany                      www.pc-disk.de

                      I   N   S   T   A   L   L

DATA TECH. DTC-7287  JUMPER SETTING

 INSTALLATION OF THE DISK DRIVES
 ===============================
 The 7287 controller has four cable connectors: J1, J2, J3, and J4.


 Floppy Drive Installation
 =========================
 Single - Floppy drive System
 ----------------------------
 Install the 34 pin header connector onto J1 of the controller with
 the colored edge of the twisted ribbon cable aligned to pin 1.

 Install the 34 pin edge connector at the end of the twisted cable
 onto the disk drive with the colored edge of the twisted ribbon cable
 aligned to pin 1 of the drive edge connector.

 Be sure the floppy disk drive terminator is installed and set the
 disk drive select switches to drive select 2. This assumes the drive
 selects are numbered 1 to 4. Refer to the specification for
 terminator settings.


 Dual - Floppy drive System
 --------------------------
 Install the 34 pin header connector onto J1 of the controller with
 the colored edge of the daisy chained cable aligned to pin 1.

 Install the other 34 pin edge connector onto the disk drives with
 with the colored edge of the daisy chained ribbon cable aligned to
 pin 1 of the drive edge connectors.

 Be sure the last physical floppy disk drive on the daisy chain has
 the terminator resistor installed The drive at the end of the cable
 will be used as drive A. Set both drives to drive select 2. This
 assumes the drive selects are numbered 1 to 4. Refer to the drive
 specification for terminator and drive select settings.


 Hard Disk Installation
 ======================
 Single - Hard Disk System
 -------------------------
 Install the 34 pin header connector onto J2 of the controller with
 the colored edge of the ribbon cable aligned to pin 1. Install the 20
 pin header connector onto J3 of the conttroller with the colored edge
 of the ribbon cable aligend to pin 1.

 Install the 20 and 34 pin edge connectors to the disk drive with the
 colored edges of the cables aligned with pin 1 of the drive edge
 connectors.

 Be sure the disk drive has the terminating resistors installed. Set
 the disk drive select switches for drive select 1 when using a flat
 34 pin cable and drive select 2 when using the end connector of a
 twisted 34 pin hard disk cable. This assumes the drive selects are
 numbered 1-4.


 Dual - Hard Disk System
 -----------------------
 Install the 34 pin header connector onto J2 of the controller with
 the colored edge of the daisy chain ribbon cable aligned to pin 1.
 Install the 20 pin header connectors onto J3 of the controller for
 drive number one and J4 for drive number two.

 Install the two 20 pin edge connectors and the 34 pin daisy chain
 ribbon cable edge connector onto the disk drives with the colored
 edges of the cable aligned with pin 1 of the drive edge connectors.

 By sure the last physical drive on the daisy chain is terminated. The
 drive at the end of the cable will be drive C. When using a flat 34
 pin daisy chain cable set drive C to drive select 1 and set drive D
 to drive select 2. When using a twisted 34 pin daisy chain cable, set
 both drives to drive select 2. This assumes the drive selects are
 numbered 1 to 4.