💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc6272.txt captured on 2024-03-21 at 17:41:33.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Internet Engineering Task Force (IETF) F. Baker
Request for Comments: 6272 D. Meyer
Category: Informational Cisco Systems
ISSN: 2070-1721 June 2011
Internet Protocols for the Smart Grid
Abstract
This note identifies the key infrastructure protocols of the Internet
Protocol Suite for use in the Smart Grid. The target audience is
those people seeking guidance on how to construct an appropriate
Internet Protocol Suite profile for the Smart Grid. In practice,
such a profile would consist of selecting what is needed for Smart
Grid deployment from the picture presented here.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc6272.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Baker & Meyer Informational [Page 1]
RFC 6272 Internet Protocols for the Smart Grid June 2011
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. The Internet Protocol Suite . . . . . . . . . . . . . . . . . 6
2.1. Internet Protocol Layers . . . . . . . . . . . . . . . . . 6
2.1.1. Application . . . . . . . . . . . . . . . . . . . . . 7
2.1.2. Transport . . . . . . . . . . . . . . . . . . . . . . 8
2.1.3. Network . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.3.1. Internet Protocol . . . . . . . . . . . . . . . . 9
2.1.3.2. Lower-Layer Networks . . . . . . . . . . . . . . . 9
2.1.4. Media Layers: Physical and Link . . . . . . . . . . . 9
2.2. Security Issues . . . . . . . . . . . . . . . . . . . . . 9
2.2.1. Physical and Data Link Layer Security . . . . . . . . 10
2.2.2. Network, Transport, and Application Layer Security . . 11
2.3. Network Infrastructure . . . . . . . . . . . . . . . . . . 13
2.3.1. Domain Name System (DNS) . . . . . . . . . . . . . . . 13
2.3.2. Network Management . . . . . . . . . . . . . . . . . . 13
3. Specific Protocols . . . . . . . . . . . . . . . . . . . . . . 14
3.1. Security Toolbox . . . . . . . . . . . . . . . . . . . . . 14
3.1.1. Authentication, Authorization, and Accounting (AAA) . 14
3.1.2. Network Layer Security . . . . . . . . . . . . . . . . 15
3.1.3. Transport Layer Security . . . . . . . . . . . . . . . 16
3.1.4. Application Layer Security . . . . . . . . . . . . . . 17
3.1.5. Secure Shell . . . . . . . . . . . . . . . . . . . . . 18
3.1.6. Key Management Infrastructures . . . . . . . . . . . . 18
3.1.6.1. PKIX . . . . . . . . . . . . . . . . . . . . . . . 18
3.1.6.2. Kerberos . . . . . . . . . . . . . . . . . . . . . 19
3.2. Network Layer . . . . . . . . . . . . . . . . . . . . . . 19
3.2.1. IPv4/IPv6 Coexistence Advice . . . . . . . . . . . . . 19
3.2.1.1. Dual Stack Coexistence . . . . . . . . . . . . . . 19
3.2.1.2. Tunneling Mechanism . . . . . . . . . . . . . . . 20
3.2.1.3. Translation between IPv4 and IPv6 Networks . . . . 20
3.2.2. Internet Protocol Version 4 . . . . . . . . . . . . . 21
3.2.2.1. IPv4 Address Allocation and Assignment . . . . . . 22
3.2.2.2. IPv4 Unicast Routing . . . . . . . . . . . . . . . 22
3.2.2.3. IPv4 Multicast Forwarding and Routing . . . . . . 22
3.2.3. Internet Protocol Version 6 . . . . . . . . . . . . . 23
3.2.3.1. IPv6 Address Allocation and Assignment . . . . . . 23
3.2.3.2. IPv6 Routing . . . . . . . . . . . . . . . . . . . 24
3.2.4. Routing for IPv4 and IPv6 . . . . . . . . . . . . . . 24
3.2.4.1. Routing Information Protocol . . . . . . . . . . . 24
3.2.4.2. Open Shortest Path First . . . . . . . . . . . . . 24
3.2.4.3. ISO Intermediate System to Intermediate System . . 25
3.2.4.4. Border Gateway Protocol . . . . . . . . . . . . . 25
3.2.4.5. Dynamic MANET On-Demand (DYMO) Routing . . . . . . 25
3.2.4.6. Optimized Link State Routing Protocol . . . . . . 26
3.2.4.7. Routing for Low-Power and Lossy Networks . . . . . 26
Baker & Meyer Informational [Page 2]
RFC 6272 Internet Protocols for the Smart Grid June 2011
3.2.5. IPv6 Multicast Forwarding and Routing . . . . . . . . 27
3.2.5.1. Protocol-Independent Multicast Routing . . . . . . 27
3.2.6. Adaptation to Lower-Layer Networks and Link Layer
Protocols . . . . . . . . . . . . . . . . . . . . . . 28
3.3. Transport Layer . . . . . . . . . . . . . . . . . . . . . 28
3.3.1. User Datagram Protocol (UDP) . . . . . . . . . . . . . 28
3.3.2. Transmission Control Protocol (TCP) . . . . . . . . . 29
3.3.3. Stream Control Transmission Protocol (SCTP) . . . . . 29
3.3.4. Datagram Congestion Control Protocol (DCCP) . . . . . 30
3.4. Infrastructure . . . . . . . . . . . . . . . . . . . . . . 30
3.4.1. Domain Name System . . . . . . . . . . . . . . . . . . 30
3.4.2. Dynamic Host Configuration . . . . . . . . . . . . . . 31
3.4.3. Network Time . . . . . . . . . . . . . . . . . . . . . 31
3.5. Network Management . . . . . . . . . . . . . . . . . . . . 31
3.5.1. Simple Network Management Protocol (SNMP) . . . . . . 31
3.5.2. Network Configuration (NETCONF) Protocol . . . . . . . 32
3.6. Service and Resource Discovery . . . . . . . . . . . . . . 33
3.6.1. Service Discovery . . . . . . . . . . . . . . . . . . 33
3.6.2. Resource Discovery . . . . . . . . . . . . . . . . . . 33
3.7. Other Applications . . . . . . . . . . . . . . . . . . . . 34
3.7.1. Session Initiation Protocol . . . . . . . . . . . . . 34
3.7.2. Extensible Messaging and Presence Protocol . . . . . . 35
3.7.3. Calendaring . . . . . . . . . . . . . . . . . . . . . 35
4. A Simplified View of the Business Architecture . . . . . . . . 35
5. Security Considerations . . . . . . . . . . . . . . . . . . . 40
6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 40
7. References . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7.1. Normative References . . . . . . . . . . . . . . . . . . . 40
7.2. Informative References . . . . . . . . . . . . . . . . . . 41
Appendix A. Example: Advanced Metering Infrastructure . . . . . . 58
A.1. How to Structure a Network . . . . . . . . . . . . . . . . 59
A.1.1. HAN Routing . . . . . . . . . . . . . . . . . . . . . 62
A.1.2. HAN Security . . . . . . . . . . . . . . . . . . . . . 62
A.2. Model 1: AMI with Separated Domains . . . . . . . . . . . 64
A.3. Model 2: AMI with Neighborhood Access to the Home . . . . 65
A.4. Model 3: Collector Is an IP Router . . . . . . . . . . . . 66
Baker & Meyer Informational [Page 3]
RFC 6272 Internet Protocols for the Smart Grid June 2011
1. Introduction
This document provides Smart Grid designers with advice on how to
best "profile" the Internet Protocol Suite (IPS) for use in Smart
Grids. It provides an overview of the IPS and the key infrastructure
protocols that are critical in integrating Smart Grid devices into an
IP-based infrastructure.
In the words of Wikipedia [SmartGrid]:
A Smart Grid is a form of electricity network utilizing digital
technology. A Smart Grid delivers electricity from suppliers to
consumers using two-way digital communications to control
appliances at consumers' homes; this saves energy, reduces costs
and increases reliability and transparency. It overlays the
ordinary electrical Grid with an information and net metering
system, that includes smart meters. Smart Grids are being
promoted by many governments as a way of addressing energy
independence, global warming and emergency resilience issues.
A Smart Grid is made possible by applying sensing, measurement and
control devices with two-way communications to electricity
production, transmission, distribution and consumption parts of
the power Grid that communicate information about Grid condition
to system users, operators and automated devices, making it
possible to dynamically respond to changes in Grid condition.
A Smart Grid includes an intelligent monitoring system that keeps
track of all electricity flowing in the system. It also has the
capability of integrating renewable electricity such as solar and
wind. When power is least expensive the user can allow the smart
Grid to turn on selected home appliances such as washing machines
or factory processes that can run at arbitrary hours. At peak
times it could turn off selected appliances to reduce demand.
Other names for a Smart Grid (or for similar proposals) include
smart electric or power Grid, intelligent Grid (or intelliGrid),
futureGrid, and the more modern interGrid and intraGrid.
That description focuses on the implications of Smart Grid technology
in the home of a consumer. In fact, data communications technologies
of various kinds are used throughout the Grid, to monitor and
maintain power generation, transmission, and distribution, as well as
the operations and management of the Grid. One can view the Smart
Grid as a collection of interconnected computer networks that
connects and serves the needs of public and private electrical
utilities and their customers.
Baker & Meyer Informational [Page 4]
RFC 6272 Internet Protocols for the Smart Grid June 2011
At the time of this writing, there is no single document that can be
described as comprising an internationally agreed standard for the
Smart Grid; that is in part the issue being addressed in its
development. The nearest approximations are probably the Smart Grid
Interoperability Panel's Conceptual Model [Model] and documents
comprising [IEC61850].
The Internet Protocol Suite (IPS) provides options for numerous
architectural components. For example, the IPS provides several
choices for the traditional transport function between two systems:
the Transmission Control Protocol (TCP) [RFC0793], the Stream Control
Transmission Protocol (SCTP) [RFC4960], and the Datagram Congestion
Control Protocol (DCCP) [RFC4340]. Another option is to select an
encapsulation such as the User Datagram Protocol (UDP) [RFC0768],
which essentially allows an application to implement its own
transport service. In practice, a designer will pick a transport
protocol that is appropriate to the problem being solved.
The IPS is standardized by the Internet Engineering Task Force
(IETF). IETF protocols are documented in the Request for Comments
(RFC) series. Several RFCs have been written describing how the IPS
should be implemented. These include:
o Requirements for Internet Hosts - Communication Layers [RFC1122],
o Requirements for Internet Hosts - Application and Support
[RFC1123],
o Requirements for IP Version 4 Routers [RFC1812], and
o IPv6 Node Requirements [RFC4294].
At the time of this writing, RFC 4294 is in the process of being
updated, in [IPv6-NODE-REQ].
This document is intended to provide Smart Grid architects and
designers with a compendium of relevant RFCs (and to some extent,
Internet Drafts), and is organized as an annotated list of RFCs. To
that end, the remainder of this document is organized as follows:
o Section 2 describes the Internet Architecture and its protocol
suite.
o Section 3 outlines a set of protocols that may be useful in Smart
Grid deployment. It is not exhaustive.
o Finally, Section 4 provides an overview of the business
architecture embodied in the design and deployment of the IPS.
Baker & Meyer Informational [Page 5]
RFC 6272 Internet Protocols for the Smart Grid June 2011
2. The Internet Protocol Suite
Before enumerating the list of Internet protocols relevant to Smart
Grid, we discuss the layered architecture of the IPS, the functions
of the various layers, and their associated protocols.
2.1. Internet Protocol Layers
While Internet architecture uses the definitions and language similar
to language used by the ISO Open System Interconnect (ISO-OSI)
reference model (Figure 1), it actually predates that model. As a
result, there is some skew in terminology. For example, the ISO-OSI
model uses "end system" while the Internet architecture uses "host".
Similarly, an "intermediate system" in the ISO-OSI model is called an
"internet gateway" or "router" in Internet parlance. Notwithstanding
these differences, the fundamental concepts are largely the same.
+--------------------+
| Application Layer |
+--------------------+
| Presentation Layer |
+--------------------+
| Session Layer |
+--------------------+
| Transport Layer |
+--------------------+
| Network Layer |
+--------------------+
| Data Link Layer |
+--------------------+
| Physical Layer |
+--------------------+
Figure 1: The ISO OSI Reference Model
The structure of the Internet reference model is shown in Figure 2.
Baker & Meyer Informational [Page 6]
RFC 6272 Internet Protocols for the Smart Grid June 2011
+---------------------------------+
|Application |
| +---------------------------+ |
| | Application Protocol | |
| +----------+----------------+ |
| | Encoding | Session Control| |
| +----------+----------------+ |
+---------------------------------+
|Transport |
| +---------------------------+ |
| | Transport Layer | |
| +---------------------------+ |
+---------------------------------+
|Network |
| +---------------------------+ |
| | Internet Protocol | |
| +---------------------------+ |
| | Lower Network Layers | |
| +---------------------------+ |
+---------------------------------+
|Media Layers |
| +---------------------------+ |
| | Data Link Layer | |
| +---------------------------+ |
| | Physical Layer | |
| +---------------------------+ |
+---------------------------------+
Figure 2: The Internet Reference Model
2.1.1. Application
In the Internet model, the Application, Presentation, and Session
layers are compressed into a single entity called "the application".
For example, the Simple Network Management Protocol (SNMP) [RFC3411]
describes an application that encodes its data in an ASN.1 profile
and engages in a session to manage a network element. The point here
is that in the Internet, the distinction between these layers exists
but is not highlighted. Further, note that in Figure 2, these
functions are not necessarily cleanly layered: the fact that an
application protocol encodes its data in some way and that it manages
sessions in some way doesn't imply a hierarchy between those
processes. Rather, the application views encoding, session
management, and a variety of other services as a tool set that it
uses while doing its work.
Baker & Meyer Informational [Page 7]
RFC 6272 Internet Protocols for the Smart Grid June 2011
2.1.2. Transport
The term "transport" is perhaps among the most confusing concepts in
the communication architecture, to a large extent because people with
various backgrounds use it to refer to "the layer below that which I
am interested in, which gets my data to my peer". For example,
optical network engineers refer to optical fiber and associated
electronics as "the transport", while web designers refer to the
Hypertext Transfer Protocol (HTTP) [RFC2616] (an application layer
protocol) as "the transport".
In the Internet protocol stack, the "transport" is the lowest
protocol layer that travels end-to-end unmodified, and it is
responsible for end-to-end data delivery services. In the Internet,
the transport layer is the layer above the network layer. Transport
layer protocols have a single minimum requirement: the ability to
multiplex several applications on one IP address. UDP [RFC0768], TCP
[RFC0793], DCCP [RFC4340], SCTP [RFC4960], and NORM [RFC5740] each
accomplish this using a pair of port numbers, one for the sender and
one for the receiver. A port number identifies an application
instance, which might be a general "listener" that peers or clients
may open sessions with, or a specific correspondent with such a
"listener". The session identification in an IP datagram is often
called the "five-tuple", and consists of the source and destination
IP addresses, the source and destination ports, and an identifier for
the transport protocol in use.
In addition, the responsibilities of a specific transport layer
protocol typically include the delivery of data (either as a stream
of messages or a stream of bytes) in a stated sequence with stated
expectations regarding delivery rate and loss. For example, TCP will
reduce its rate in response to loss, as a congestion control trigger,
while DCCP accepts some level of loss if necessary to maintain
timeliness.
2.1.3. Network
The main function of the network layer is to identify a remote
destination and deliver data to it. In connection-oriented networks
such as Multi-protocol Label Switching (MPLS) [RFC3031] or
Asynchronous Transfer Mode (ATM), a path is set up once, and data is
delivered through it. In connectionless networks such as Ethernet
and IP, data is delivered as datagrams. Each datagram contains both
the source and destination network layer addresses, and the network
is responsible for delivering it. In the Internet Protocol Suite,
the Internet Protocol is the network that runs end to end. It may be
encapsulated over other LAN and WAN technologies, including both IP
networks and networks of other types.
Baker & Meyer Informational [Page 8]
RFC 6272 Internet Protocols for the Smart Grid June 2011
2.1.3.1. Internet Protocol
IPv4 and IPv6, each of which is called the Internet Protocol, are
connectionless ("datagram") architectures. They are designed as
common elements that interconnect network elements across a network
of lower-layer networks. In addition to the basic service of
identifying a datagram's source and destination, they offer services
to fragment and reassemble datagrams when necessary, assist in
diagnosis of network failures, and carry additional information
necessary in special cases.
The Internet layer provides a uniform network abstraction network
that hides the differences between various network technologies.
This is the layer that allows diverse networks such as Ethernet,
802.15.4, etc. to be combined into a uniform IP network. New network
technologies can be introduced into the IP Protocol Suite by defining
how IP is carried over those technologies, leaving the other layers
of the IPS and applications that use those protocol unchanged.
2.1.3.2. Lower-Layer Networks
The network layer can be recursively subdivided as needed. This may
be accomplished by tunneling, in which an IP datagram is encapsulated
in another IP header for delivery to a decapsulator. IP is
frequently carried in Virtual Private Networks (VPNs) across the
public Internet using tunneling technologies such as the Tunnel mode
of IPsec, IP-in-IP, and Generic Route Encapsulation (GRE) [RFC2784].
In addition, IP is also frequently carried in circuit networks such
as MPLS [RFC4364], GMPLS, and ATM. Finally, IP is also carried over
wireless networks (IEEE 802.11, 802.15.4, or 802.16) and switched
Ethernet (IEEE 802.3) networks.
2.1.4. Media Layers: Physical and Link
At the lowest layer of the IP architecture, data is encoded in
messages and transmitted over the physical media. While the IETF
specifies algorithms for carrying IPv4 and IPv6 various media types,
it rarely actually defines the media -- it happily uses
specifications from IEEE, ITU, and other sources.
2.2. Security Issues
While complaining about the security of the Internet is popular, it
is important to distinguish between attacks on protocols and attacks
on users (e.g., phishing). Attacks on users are largely independent
of protocol details, reflecting interface design issues or user
education problems, and are out of scope for this document. Security
problems with Internet protocols are in scope, of course, and can
Baker & Meyer Informational [Page 9]
RFC 6272 Internet Protocols for the Smart Grid June 2011
often be mitigated using existing security features already specified
for the protocol, or by leveraging the security services offered by
other IETF protocols. See the Security Assessment of the
Transmission Control Protocol (TCP) [TCP-SEC] and the Security
Assessment of the Internet Protocol version 4 [IP-SEC] for more
information on TCP and IPv4 issues, respectively.
These solutions do, however, need to get deployed as well. The road
to widespread deployment can sometimes be painful since often
multiple stakeholders need to take actions. Experience has shown
that this takes some time, and very often only happens when the
incentives are high enough in relation to the costs.
Furthermore, it is important to stress that available standards are
important, but the range of security problems is larger than a
missing standard; many security problems are the result of
implementation bugs and the result of certain deployment choices.
While these are outside the realm of standards development, they play
an important role in the security of the overall system. Security
has to be integrated into the entire process.
The IETF takes security seriously in the design of their protocols
and architectures; every IETF specification has to have a Security
Considerations section to document the offered security threats and
countermeasures. RFC 3552 [RFC3552] provides recommendations on
writing such a Security Considerations section. It also describes
the classical Internet security threat model and lists common
security goals.
In a nutshell, security has to be integrated into every protocol,
protocol extension, and consequently, every layer of the protocol
stack to be useful. We illustrate this also throughout this document
with references to further security discussions. Our experience has
shown that dealing with security as an afterthought does not lead to
the desired outcome.
The discussion of security threats and available security mechanisms
aims to illustrate some of the design aspects that commonly appear.
2.2.1. Physical and Data Link Layer Security
At the physical and data link layers, threats generally center on
physical attacks on the network -- the effects of backhoes,
deterioration of physical media, and various kinds of environmental
noise. Radio-based networks are subject to signal fade due to
distance, interference, and environmental factors; it is widely noted
that IEEE 802.15.4 networks frequently place a metal ground plate
between the meter and the device that manages it. Fiber was at one
Baker & Meyer Informational [Page 10]
RFC 6272 Internet Protocols for the Smart Grid June 2011
time deployed because it was believed to be untappable; we have since
learned to tap it by bending the fiber and collecting incidental
light, and we have learned about backhoes. As a result, some
installations encase fiber optic cable in a pressurized sheath, both
to quickly identify the location of a cut and to make it more
difficult to tap.
While there are protocol behaviors that can detect certain classes of
physical faults, such as keep-alive exchanges, physical security is
generally not considered to be a protocol problem.
For wireless transmission technologies, eavesdropping on the
transmitted frames is also typically a concern. Additionally, those
operating networks may want to ensure that access to their
infrastructure is restricted to those who are authenticated and
authorized (typically called 'network access authentication'). This
procedure is often offered by security primitives at the data link
layer.
2.2.2. Network, Transport, and Application Layer Security
At the network, transport, and application layers, it is common to
demand a few basic security requirements, commonly referred to as CIA
(Confidentiality, Integrity, and Availability):
1. Confidentiality: Protect the transmitted data from unauthorized
disclosure (i.e., keep eavesdroppers from learning what was
transmitted). For example, for trust in e-commerce applications,
credit card transactions are exchanged encrypted between the Web
browser and a Web server.
2. Integrity: Protect against unauthorized changes to exchanges,
including both intentional change or destruction and accidental
change or loss, by ensuring that changes to exchanges are
detectable. It has two parts: one for the data and one for the
peers.
* Peers need to verify that information that appears to be from
a trusted peer is really from that peer. This is typically
called 'data origin authentication'.
* Peers need to validate that the content of the data exchanged
is unmodified. The term typically used for this property is
'data integrity'.
3. Availability: Ensure that the resource is accessible by
mitigating of denial-of-service attacks.
Baker & Meyer Informational [Page 11]
RFC 6272 Internet Protocols for the Smart Grid June 2011
To this we add authenticity, which requires that the communicating
peers prove that they are in fact who they say they are to each other
(i.e., mutual authentication). This generally means knowing "who"
the peer is, and that they demonstrate the possession of a "secret"
as part of the security protocol interaction.
The following three examples aim to illustrate these security
requirements.
One common attack against a TCP session is to bombard the session
with reset messages. Other attacks against TCP include the "SYN
flooding" attack, in which an attacker attempts to exhaust the memory
of the target by creating TCP state. In particular, the attacker
attempts to exhaust the target's memory by opening a large number of
unique TCP connections, each of which is represented by a
Transmission Control Block (TCB). The attack is successful if the
attacker can cause the target to fill its memory with TCBs.
A number of mechanisms have been developed to deal with these types
of denial-of-service attacks. One, "SYN Cookies", delays state
establishment on the server side to a later phase in the protocol
exchange. Another mechanism, specifically targeting the reset attack
cited above, provides authentication services in TCP itself to ensure
that fake resets are rejected.
Another approach would be to offer security protection already at a
lower layer, such as IPsec (see Section 3.1.2) or TLS (see
Section 3.1.3), so that a host can identify legitimate messages and
discard the others, thus mitigating any damage that may have been
caused by the attack.
Another common attack involves unauthorized access to resources. For
example, an unauthorized party might try to attach to a network. To
protect against such an attack, an Internet Service Provider (ISP)
typically requires network access authentication of new hosts
demanding access to the network and to the Internet prior to offering
access. This exchange typically requires authentication of that
entity and a check in the ISPs back-end database to determine whether
corresponding subscriber records exist and are still valid (e.g.,
active subscription and sufficient credits).
From the discussion above, establishing a secure communication
channel is clearly an important concept frequently used to mitigate a
range of attacks. Unfortunately, focusing only on channel security
may not be enough for a given task. Threat models have evolved and
even some of the communication endpoints cannot be considered fully
trustworthy, i.e., even trusted peers may act maliciously.
Baker & Meyer Informational [Page 12]
RFC 6272 Internet Protocols for the Smart Grid June 2011
Furthermore, many protocols are more sophisticated in their protocol
interaction and involve more than two parties in the protocol
exchange. Many of the application layer protocols, such as email,
instant messaging, voice over IP, and presence-based applications,
fall into this category. With this class of protocols, secure data,
such as DNS records, and secure communications with middleware,
intermediate servers, and supporting applications need to be
considered as well as the security of the direct communication. A
detailed treatment of the security threats and requirements of these
multi-party protocols is beyond this specification but the interested
reader is referred to the above-mentioned examples for an
illustration of what technical mechanisms have been investigated and
proposed in the past.
2.3. Network Infrastructure
While the following protocols are not critical to the design of a
specific system, they are important to running a network, and as such
are surveyed here.
2.3.1. Domain Name System (DNS)
The DNS' main function is translating names to numeric IP addresses.
While this is not critical to running a network, certain functions
are made a lot easier if numeric addresses can be replaced with
mnemonic names. This facilitates renumbering of networks and
generally improves the manageability and serviceability of the
network. DNS has a set of security extensions called DNSSEC, which
can be used to provide strong cryptographic authentication to the
DNS. DNS and DNSSEC are discussed further in Section 3.4.1.
2.3.2. Network Management
Network management has proven to be a difficult problem. As such,
various solutions have been proposed, implemented, and deployed.
Each solution has its proponents, all of whom have solid arguments
for their viewpoints. The IETF has two major network management
solutions for device operation: SNMP, which is ASN.1-encoded and is
primarily used for monitoring of system variables, and NETCONF
[RFC4741], which is XML-encoded and primarily used for device
configuration.
Another aspect of network management is the initial provisioning and
configuration of hosts, which is discussed in Section 3.4.2. Note
that Smart Grid deployments may require identity authentication and
authorization (as well as other provisioning and configuration) that
may not be within the scope of either DHCP or Neighbor Discovery.
While the IP Protocol Suite has limited support for secure
Baker & Meyer Informational [Page 13]
RFC 6272 Internet Protocols for the Smart Grid June 2011
provisioning and configuration, these problems have been solved using
IP protocols in specifications such as DOCSIS 3.0 [SP-MULPIv3.0].
3. Specific Protocols
In this section, having briefly laid out the IP architecture and some
of the problems that the architecture tries to address, we introduce
specific protocols that might be appropriate to various Smart Grid
use cases. Use cases should be analyzed along with privacy,
Authentication, Authorization, and Accounting (AAA), transport, and
network solution dimensions. The following sections provide guidance
for such analysis.
3.1. Security Toolbox
As noted, a key consideration in security solutions is a good threat
analysis coupled with appropriate mitigation strategies at each
layer. The IETF has over time developed a number of building blocks
for security based on the observation that protocols often demand
similar security services. The following sub-sections outline a few
of those commonly used security building blocks. Reusing them offers
several advantages, such as availability of open source code,
experience with existing systems, a number of extensions that have
been developed, and the confidence that the listed technologies have
been reviewed and analyzed by a number of security experts.
It is important to highlight that in addition to the mentioned
security tools, every protocol often comes with additional, often
unique security considerations that are specific to the domain in
which the protocol operates. Many protocols include features
specifically designed to mitigate these protocol-specific risks. In
other cases, the security considerations will identify security-
relevant services that are required from other network layers to
achieve appropriate levels of security.
3.1.1. Authentication, Authorization, and Accounting (AAA)
While the term AAA sounds generic and applicable to all sorts of
security protocols, it has been, in the IETF, used in relation to
network access authentication and is associated with the RADIUS
([RFC2865]) and the Diameter protocol ([RFC3588], [DIME-BASE]) in
particular.
The authentication procedure for network access aims to deal with the
task of verifying that a peer is authenticated and authorized prior
to accessing a particular resource (often connectivity to the
Internet). Typically, the authentication architecture for network
access consists of the following building blocks: the Extensible
Baker & Meyer Informational [Page 14]
RFC 6272 Internet Protocols for the Smart Grid June 2011
Authentication Protocol (EAP [RFC4017]) as a container to encapsulate
EAP methods, an EAP Method (as a specific way to perform
cryptographic authentication and key exchange, such as described in
RFC 5216 [RFC5216] and RFC 5433 [RFC5433]), a protocol that carries
EAP payloads between the end host and a server-side entity (such as a
network access server), and a way to carry EAP payloads to back-end
server infrastructure (potentially in a cross-domain scenario) to
provide authorization and accounting functionality. The latter part
is provided by RADIUS and Diameter. To carry EAP payloads between
the end host and a network access server, different mechanisms have
been standardized, such as the Protocol for Carrying Authentication
for Network Access (PANA) [RFC5191] and IEEE 802.1X [IEEE802.1X].
For access to remote networks, such as enterprise networks, the
ability to utilize EAP within IKEv2 [RFC5996] has also been
developed.
More recently, the same architecture with EAP and RADIUS/Diameter is
being reused for application layer protocols. More details about
this architectural variant can be found in [ABFAB-ARCH].
3.1.2. Network Layer Security
IP security, as described in [RFC4301], addresses security at the IP
layer, provided through the use of a combination of cryptographic and
protocol security mechanisms. It offers a set of security services
for traffic at the IP layer, in both the IPv4 and IPv6 environment.
The set of security services offered includes access control,
connectionless integrity, data origin authentication, detection and
rejection of replays (a form of partial sequence integrity),
confidentiality (via encryption), and limited traffic-flow
confidentiality. These services are provided at the IP layer,
offering protection in a standard fashion for all protocols that may
be carried over IP (including IP itself).
The architecture foresees a split between the rather time-consuming
(a) authentication and key exchange protocol step that also
establishes a security association (a data structure with keying
material and security parameters) and (b) the actual data traffic
protection.
For the former step, the Internet Key Exchange protocol version 2
(IKEv2 [RFC5996]) is the most recent edition of the standardized
protocol. IKE negotiates each of the cryptographic algorithms that
will be used to protect the data independently, somewhat like
selecting items a la carte.
For the actual data protection, two types of protocols have
historically been used, namely the IP Authentication Header (AH)
Baker & Meyer Informational [Page 15]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC4302] and the Encapsulating Security Payload (ESP) [RFC4303].
The two differ in the security services they offer; the most
important distinction is that ESP offers confidentiality protection
while AH does not. Since ESP can also provide authentication
services, most recent protocol developments making use of IPsec only
specify use of ESP and do not use AH.
In addition to these base line protocol mechanisms a number of
extensions have been developed for IKEv2 (e.g., an extension to
perform EAP-only authentication [RFC5998]) and since the architecture
supports flexible treatment of cryptographic algorithms a number of
them have been specified (e.g., [RFC4307] for IKEv2, and [RFC4835]
for AH and ESP).
3.1.3. Transport Layer Security
Transport Layer Security v1.2 [RFC5246] are security services that
protect data above the transport layer. The protocol allows client/
server applications to communicate in a way that is designed to
prevent eavesdropping, tampering, or message forgery. TLS is
application protocol independent.
TLS is composed of two layers: the TLS Record protocol and the TLS
Handshake protocol. The TLS Record protocol provides connection
security that has two basic properties: (a) confidentiality
protection and (b) integrity protection.
The TLS Handshake protocol allows the server and client to
authenticate each other and to negotiate an encryption algorithm and
cryptographic keys before the application protocol transmits or
receives its first byte of data. The negotiated parameters and the
derived keying material is then used by the TLS Record protocol to
perform its job.
Unlike IKEv2/IPsec, TLS negotiates these cryptographic parameters in
suites, so-called 'cipher suites'. Examples of cipher suites that
can be negotiated with TLS include Elliptic Curve Cryptography (ECC)
[RFC4492] [RFC5289] [AES-CCM-ECC], Camellia [RFC5932], and the Suite
B Profile [RFC5430]. [IEC62351-3] outlines the use of different TLS
cipher suites for use in the Smart Grid. The basic cryptographic
mechanisms for ECC have been documented in [RFC6090].
TLS must run over a reliable transport channel -- typically TCP. In
order to offer the same security services for unreliable datagram
traffic, such as UDP, the Datagram Transport Layer Security (DTLS
[RFC4347] [DTLS]) was developed.
Baker & Meyer Informational [Page 16]
RFC 6272 Internet Protocols for the Smart Grid June 2011
3.1.4. Application Layer Security
In certain cases, the application layer independent security
mechanisms described in the previous sub-sections are not sufficient
to deal with all the identified threats. For this purpose, a number
of security primitives are additionally available at the application
layer where the semantic of the application can be considered.
We will focus our description on a few mechanisms that are commonly
used throughout the Internet.
Cryptographic Message Syntax (CMS [RFC5652]) is an encapsulation
syntax to sign, digest, authenticate, or encrypt arbitrary message
content. It also allows arbitrary attributes, such as signing time,
to be signed along with the message content, and it provides for
other attributes such as countersignatures to be associated with a
signature. The CMS can support a variety of architectures for
certificate-based key management, such as the one defined by the PKIX
(Public Key Infrastructure using X.509) working group [RFC5280]. The
CMS has been leveraged to supply security services in a variety of
protocols, including secure email [RFC5751], key management [RFC5958]
[RFC6031], and firmware updates [RFC4108].
Related work includes the use of digital signatures on XML-encoded
documents, which has been jointly standardized by W3C and the IETF
[RFC3275]. Digitally signed XML is a good choice where applications
natively support XML-encoded data, such as the Extensible Messaging
and Presence Protocol (XMPP).
More recently, the work on delegated authentication and authorization
often demanded by Web applications have been developed with the Open
Web Authentication (OAuth) protocol [RFC5849] [OAUTHv2]. OAuth is
used by third-party applications to gain access to protected
resources (such as energy consumption information about a specific
household) without having the resource owner share its long-term
credentials with that third-party. In OAuth, the third-party
application requests access to resources controlled by the resource
owner and hosted by the resource server, and is issued a different
set of credentials than those of the resource owner. More
specifically, the third-party applications obtain an access token
during the OAuth protocol exchange. This token denotes a specific
scope, duration, and other access attributes. As a result, it
securely gains access to the protected resource with the consent of
the resource owner.
Baker & Meyer Informational [Page 17]
RFC 6272 Internet Protocols for the Smart Grid June 2011
3.1.5. Secure Shell
The Secure Shell (SSH) protocol [RFC4253] has been widely used by
administrators and others for secure remote login, but is also usable
for secure tunneling. More recently, protocols have chosen to layer
on top of SSH for transport security services; for example, the
NETCONF network management protocol (see Section 3.5.2) uses SSH as
its main communications security protocol.
3.1.6. Key Management Infrastructures
All of the security protocols discussed above depend on cryptography
for security, and hence require some form of key management. Most
IETF protocols at least nominally require some scalable form of key
management to be defined as mandatory to implement; indeed the lack
of such key management features has in the past been a reason to
delay approval of protocols. There are two generic key management
schemes that are widely used by other Internet protocols, PKIX and
Kerberos, each of which is briefly described below.
3.1.6.1. PKIX
Public Key Infrastructure (PKI) refers to the kind of key management
that is based on certification authorities (CAs) issuing public key
certificates for other key holders. By chaining from a trust anchor
(a locally trusted copy of a CA public key) down to the public key of
some protocol peer, PKI allows for secure binding between keys and
protocol-specific names, such as email addresses, and hence enables
security services such as data and peer authentication, data
integrity, and confidentiality (encryption).
The main Internet standard for PKI is [RFC5280], which is a profile
of the X.509 public key certificate format. There are a range of
private and commercial CAs operating today providing the ability to
manage and securely distribute keys for all protocols that use public
key certificates, e.g., TLS and S/MIME. In addition to the profile
standard, the PKIX working group has defined a number of management
protocols (e.g., [RFC5272] and [RFC4210]) as well as protocols for
handling revocation of public key certificates such as the Online
Certificate Status Protocol (OCSP) [RFC2560].
PKI is generally perceived to better handle use-cases spanning
multiple independent domains when compared to Kerberos.
Baker & Meyer Informational [Page 18]
RFC 6272 Internet Protocols for the Smart Grid June 2011
3.1.6.2. Kerberos
The Kerberos Network Authentication System [RFC4120] is commonly used
within organizations to centralize authentication, authorization, and
policy in one place. Kerberos natively supports usernames and
passwords as the basis of authentication. With Public Key
Cryptography for Initial Authentication in Kerberos (PKINIT)
[RFC4556], Kerberos supports certificate or public-key-based
authentication. This may provide an advantage by concentrating
policy about certificate validation and mapping of certificates to
user accounts in one place. Through the GSS-API [RFC1964] [RFC2743]
[RFC4121], Kerberos can be used to manage authentication for most
applications. While Kerberos works best within organizations and
enterprises, it does have facilities that permit authentication to be
shared between administrative domains.
3.2. Network Layer
The IPS specifies two network layer protocols: IPv4 and IPv6. The
following sections describe the IETF's coexistence and transition
mechanisms for IPv4 and IPv6.
Note that on 3 February 2011, the IANA's IPv4 free pool (the pool of
available, unallocated IPv4 addresses) was exhausted, and the
Regional Internet Registrars' (RIRs') free pools are expected to be
exhausted during the coming year, if not sooner. The IETF, the IANA,
and the RIRs recommend that new deployments use IPv6, and that IPv4
infrastructures be supported via the mechanisms described in
Section 3.2.1.
3.2.1. IPv4/IPv6 Coexistence Advice
The IETF has specified a variety of mechanisms designed to facilitate
IPv4/IPv6 coexistence. The IETF actually recommends relatively few
of them: the current advice to network operators is found in
Guidelines for Using IPv6 Transition Mechanisms [RFC6180]. The
thoughts in that document are replicated here.
3.2.1.1. Dual Stack Coexistence
The simplest coexistence approach is to
o provide a network that routes both IPv4 and IPv6,
o ensure that servers and their applications similarly support both
protocols, and
Baker & Meyer Informational [Page 19]
RFC 6272 Internet Protocols for the Smart Grid June 2011
o require that all new systems and applications purchased or
upgraded support both protocols.
The net result is that over time all systems become protocol
agnostic, and that eventually maintenance of IPv4 support becomes a
business decision. This approach is described in the Basic
Transition Mechanisms for IPv6 Hosts and Routers [RFC4213].
3.2.1.2. Tunneling Mechanism
In those places in the network that support only IPv4, the simplest
and most reliable approach to coexistence is to provide virtual
connectivity using tunnels or encapsulations. Early in IPv6
deployment, this was often done using static tunnels. A more dynamic
approach is documented in IPv6 Rapid Deployment on IPv4
Infrastructures (6rd) [RFC5569].
3.2.1.3. Translation between IPv4 and IPv6 Networks
In those cases where an IPv4-only host would like to communicate with
an IPv6-only host (or vice versa), a need for protocol translation
may be indicated. At first blush, protocol translation may appear
trivial; on deeper inspection, it turns out that protocol translation
can be complicated.
The most reliable approach to protocol translation is to provide
application layer proxies or gateways, which natively enable
application-to-application connections using both protocols and can
use whichever is appropriate. For example, a web proxy might use
both protocols and as a result enable an IPv4-only system to run HTTP
across an IPv6-only network or to a web server that implements only
IPv6. Since this approach is a service of a protocol-agnostic
server, it is not the subject of standardization by the IETF.
For those applications in which network layer translation is
indicated, the IETF has designed a translation mechanism, which is
described in the following documents:
o Framework for IPv4/IPv6 Translation [RFC6144]
o IPv6 Addressing of IPv4/IPv6 Translators [RFC6052]
o DNS extensions [RFC6147]
o IP/ICMP Translation Algorithm [RFC6145]
o Translation from IPv6 Clients to IPv4 Servers [RFC6146]
Baker & Meyer Informational [Page 20]
RFC 6272 Internet Protocols for the Smart Grid June 2011
As with IPv4/IPv4 Network Address Translation, translation between
IPv4 and IPv6 has limited real world applicability for an application
protocol that carries IP addresses in its payload and expects those
addresses to be meaningful to both client and server. However, for
those protocols that do not, protocol translation can provide a
useful network extension.
Network-based translation provides for two types of services:
stateless (and therefore scalable and load-sharable) translation
between IPv4 and IPv6 addresses that embed an IPv4 address in them,
and stateful translation similar to IPv4/IPv4 translation between
IPv4 addresses. The stateless mode is straightforward to implement,
but due to the embedding, requires IPv4 addresses to be allocated to
an otherwise IPv6-only network, and is primarily useful for IPv4-
accessible servers implemented in the IPv6 network. The stateful
mode allows clients in the IPv6 network to access servers in the IPv4
network, but does not provide such service for IPv4 clients accessing
IPv6 peers or servers with general addresses; it has the advantage
that it does not require that a unique IPv4 address be embedded in
the IPv6 address of hosts using this mechanism.
Finally, note that some site networks are IPv6 only while some
transit networks are IPv4 only. In these cases, it may be necessary
to tunnel IPv6 over IPv4 or translate between IPv6 and IPv4.
3.2.2. Internet Protocol Version 4
IPv4 [RFC0791] and the Internet Control Message Protocol (ICMP)
[RFC0792] comprise the IPv4 network layer. IPv4 provides unreliable
delivery of datagrams.
IPv4 also provides for fragmentation and reassembly of long datagrams
for transmission through networks with small Maximum Transmission
Units (MTU). The MTU is the largest packet size that can be
delivered across the network. In addition, the IPS provides ICMP
[RFC0792], which is a separate protocol that enables the network to
report errors and other issues to hosts that originate problematic
datagrams.
IPv4 originally supported an experimental type of service field that
identified eight levels of operational precedence styled after the
requirements of military telephony, plus three and later four bit
flags that OSI IS-IS for IPv4 (IS-IS) [RFC1195] and OSPF Version 2
[RFC2328] interpreted as control traffic; this control traffic is
assured of not being dropped when queued or upon receipt, even if
other traffic is being dropped. These control bits turned out to be
less useful than the designers had hoped. They were replaced by the
Differentiated Services Architecture [RFC2474] [RFC2475], which
Baker & Meyer Informational [Page 21]
RFC 6272 Internet Protocols for the Smart Grid June 2011
contains a six-bit code point used to select an algorithm (a "per-hop
behavior") to be applied to the datagram. The IETF has also produced
a set of Configuration Guidelines for DiffServ Service Classes
[RFC4594], which describes a set of service classes that may be
useful to a network operator.
3.2.2.1. IPv4 Address Allocation and Assignment
IPv4 addresses are administratively assigned, usually using automated
methods, using the Dynamic Host Configuration Protocol (DHCP)
[RFC2131]. On most interface types, neighboring systems identify
each others' addresses using the Address Resolution Protocol (ARP)
[RFC0826].
3.2.2.2. IPv4 Unicast Routing
Routing for the IPv4 Internet is accomplished by routing applications
that exchange connectivity information and build semi-static
destination routing databases. If a datagram is directed to a given
destination address, the address is looked up in the routing
database, and the most specific ("longest") prefix found that
contains it is used to identify the next-hop router or the end system
to which it will be delivered. This is not generally implemented on
hosts, although it can be; a host normally sends datagrams to a
router on its local network, and the router carries out the intent.
IETF specified routing protocols include RIP Version 2 [RFC2453], OSI
IS-IS for IPv4 [RFC1195], OSPF Version 2 [RFC2328], and BGP-4
[RFC4271]. Active research exists in mobile ad hoc routing and other
routing paradigms; these result in new protocols and modified
forwarding paradigms.
3.2.2.3. IPv4 Multicast Forwarding and Routing
IPv4 was originally specified as a unicast (point to point) protocol,
and was extended to support multicast in [RFC1112]. This uses the
Internet Group Management Protocol [RFC3376] [RFC4604] to enable
applications to join multicast groups, and for most applications uses
Source-Specific Multicast [RFC4607] for routing and delivery of
multicast messages.
An experiment carried out in IPv4 that is not part of the core
Internet architecture but may be of interest in the Smart Grid is the
development of so-called "Reliable Multicast". This is "so-called"
because it is not "reliable" in the strict sense of the word -- it is
perhaps better described as "enhanced reliability". A best effort
network by definition can lose traffic, duplicate it, or reorder it,
something as true for multicast as for unicast. Research in
Baker & Meyer Informational [Page 22]
RFC 6272 Internet Protocols for the Smart Grid June 2011
"Reliable Multicast" technology intends to improve the probability of
delivery of multicast traffic.
In that research, the IETF imposed guidelines [RFC2357] on the
research community regarding what was desirable. Important results
from that research include a number of papers and several proprietary
protocols including some that have been used in support of business
operations. RFCs in the area include The Use of Forward Error
Correction (FEC) in Reliable Multicast [RFC3453], the Negative-
acknowledgment (NACK)-Oriented Reliable Multicast (NORM) Protocol
[RFC5740], and the Selectively Reliable Multicast Protocol (SRMP)
[RFC4410].
3.2.3. Internet Protocol Version 6
IPv6 [RFC2460], with the Internet Control Message Protocol "v6"
[RFC4443], constitutes the next generation protocol for the Internet.
IPv6 provides for transmission of datagrams from source to
destination hosts, which are identified by fixed-length addresses.
IPv6 also provides for fragmentation and reassembly of long datagrams
by the originating host, if necessary, for transmission through
"small packet" networks. ICMPv6, which is a separate protocol
implemented along with IPv6, enables the network to report errors and
other issues to hosts that originate problematic datagrams.
IPv6 adopted the Differentiated Services Architecture [RFC2474]
[RFC2475], which contains a six-bit code point used to select an
algorithm (a "per-hop behavior") to be applied to the datagram.
The IPv6 over Low-Power Wireless Personal Area Networks RFC [RFC4919]
and the Compression Format for IPv6 Datagrams in 6LoWPAN Networks
document [6LOWPAN-HC] addresses IPv6 header compression and subnet
architecture in at least some sensor networks, and may be appropriate
to the Smart Grid Advanced Metering Infrastructure or other sensor
domains.
3.2.3.1. IPv6 Address Allocation and Assignment
An IPv6 Address [RFC4291] may be administratively assigned using
DHCPv6 [RFC3315] in a manner similar to the way IPv4 addresses are.
In addition, IPv6 addresses may also be autoconfigured.
Autoconfiguration enables various models of network management that
may be advantageous in different use cases. Autoconfiguration
procedures are defined in [RFC4862] and [RFC4941]. IPv6 neighbors
identify each others' addresses using Neighbor Discovery (ND)
[RFC4861]. SEcure Neighbor Discovery (SEND) [RFC3971] may be used to
secure these operations.
Baker & Meyer Informational [Page 23]
RFC 6272 Internet Protocols for the Smart Grid June 2011
3.2.3.2. IPv6 Routing
Routing for the IPv6 Internet is accomplished by routing applications
that exchange connectivity information and build semi-static
destination routing databases. If a datagram is directed to a given
destination address, the address is looked up in the routing
database, and the most specific ("longest") prefix found that
contains it is used to identify the next-hop router or the end system
to which it will be delivered. Routing is not generally implemented
on hosts (although it can be); generally, a host sends datagrams to a
router on its local network, and the router carries out the intent.
IETF-specified routing protocols include RIP for IPv6 [RFC2080],
IS-IS for IPv6 [RFC5308], OSPF for IPv6 [RFC5340], and BGP-4 for IPv6
[RFC2545]. Active research exists in mobile ad hoc routing, routing
in low-power networks (sensors and Smart Grids), and other routing
paradigms; these result in new protocols and modified forwarding
paradigms.
3.2.4. Routing for IPv4 and IPv6
3.2.4.1. Routing Information Protocol
The prototypical routing protocol used in the Internet has probably
been the Routing Information Protocol [RFC1058]. People that use it
today tend to deploy RIPng for IPv6 [RFC2080] and RIP Version 2
[RFC2453]. Briefly, RIP is a distance vector routing protocol that
is based on a distributed variant of the widely known Bellman-Ford
algorithm. In distance vector routing protocols, each router
announces the contents of its route table to neighboring routers,
which integrate the results with their route tables and re-announce
them to others. It has been characterized as "routing by rumor", and
suffers many of the ills we find in human gossip -- propagating stale
or incorrect information in certain failure scenarios, and being in
cases unresponsive to changes in topology. [RFC1058] provides
guidance to algorithm designers to mitigate these issues.
3.2.4.2. Open Shortest Path First
The Open Shortest Path First (OSPF) routing protocol is one of the
more widely used protocols in the Internet. OSPF is based on
Dijkstra's well known Shortest Path First (SPF) algorithm. It is
implemented as OSPF Version 2 [RFC2328] for IPv4, OSPF for IPv6
[RFC5340] for IPv6, and the Support of Address Families in OSPFv3
[RFC5838] to enable [RFC5340] routing both IPv4 and IPv6.
The advantage of any SPF-based protocol (i.e., OSPF and IS-IS) is
primarily that every router in the network constructs its view of the
Baker & Meyer Informational [Page 24]
RFC 6272 Internet Protocols for the Smart Grid June 2011
network from first-hand knowledge rather than the "gossip" that
distance vector protocols propagate. As such, the topology is
quickly and easily changed by simply announcing the change. The
disadvantage of SPF-based protocols is that each router must store a
first-person statement of the connectivity of each router in the
domain.
3.2.4.3. ISO Intermediate System to Intermediate System
The Intermediate System to Intermediate System (IS-IS) routing
protocol is one of the more widely used protocols in the Internet.
IS-IS is also based on Dijkstra's SPF algorithm. It was originally
specified as ISO DP 10589 for the routing of Connectionless Network
Service (CLNS), and extended for routing in TCP/IP and dual
environments [RFC1195], and more recently for routing of IPv6
[RFC5308].
As with OSPF, the positives of any SPF-based protocol and
specifically IS-IS are primarily that the network is described as a
lattice of routers with connectivity to subnets and isolated hosts.
It's topology is quickly and easily changed by simply announcing the
change, without the issues of "routing by rumor", since every host
within the routing domain has a first-person statement of the
connectivity of each router in the domain. The negatives are a
corollary: each router must store a first-person statement of the
connectivity of each router in the domain.
3.2.4.4. Border Gateway Protocol
The Border Gateway Protocol (BGP) [RFC4271] is widely used in the
IPv4 Internet to exchange routes between administrative entities --
service providers, their peers, their upstream networks, and their
customers -- while applying specific policy. Multiprotocol
Extensions [RFC4760] to BGP allow BGP to carry IPv6 Inter-Domain
Routing [RFC2545], multicast reachability information, and VPN
information, among others.
Considerations that apply with BGP deal with the flexibility and
complexity of the policies that must be defined. Flexibility is a
good thing; in a network that is not run by professionals, the
complexity is burdensome.
3.2.4.5. Dynamic MANET On-Demand (DYMO) Routing
The Mobile Ad Hoc working group of the IETF developed, among other
protocols, Ad hoc On-Demand Distance Vector (AODV) Routing [RFC3561].
This protocol captured the minds of some in the embedded devices
industry, but experienced issues in wireless networks such as
Baker & Meyer Informational [Page 25]
RFC 6272 Internet Protocols for the Smart Grid June 2011
802.15.4 and 802.11's Ad Hoc mode. As a result, it is in the process
of being updated in the Dynamic MANET On-demand (DYMO) Routing
protocol [DYMO].
AODV and DYMO are essentially reactive routing protocols designed for
mobile ad hoc networks, and usable in other forms of ad hoc networks.
They provide connectivity between a device within a distributed
subnet and a few devices (including perhaps a gateway or router to
another subnet) without tracking connectivity to other devices. In
essence, routing is calculated and discovered upon need, and a host
or router need only maintain the routes that currently work and are
needed.
3.2.4.6. Optimized Link State Routing Protocol
The Optimized Link State Routing Protocol (OLSR) [RFC3626] is a
proactive routing protocol designed for mobile ad hoc networks, and
can be used in other forms of ad hoc networks. It provides arbitrary
connectivity between systems within a distributed subnet. As with
protocols designed for wired networks, routing is calculated whenever
changes are detected, and maintained in each router's tables. The
set of nodes that operate as routers within the subnet, however, are
fairly fluid, and dependent on this instantaneous topology of the
subnet.
3.2.4.7. Routing for Low-Power and Lossy Networks
The IPv6 Routing Protocol for Low power and Lossy Networks (RPL)
[RPL] is a reactive routing protocol designed for use in resource
constrained networks. Requirements for resource constrained networks
are defined in [RFC5548], [RFC5673], [RFC5826], and [RFC5867].
Briefly, a constrained network is comprised of nodes that:
o Are built with limited processing power and memory, and sometimes
energy when operating on batteries.
o Are interconnected through a low-data-rate network interface and
are potentially vulnerable to communication instability and low
packet delivery rates.
o Potentially have a mix of roles such as being able to act as a
host (i.e., generating traffic) and/or a router (i.e., both
forwarding and generating RPL traffic).
Baker & Meyer Informational [Page 26]
RFC 6272 Internet Protocols for the Smart Grid June 2011
3.2.5. IPv6 Multicast Forwarding and Routing
IPv6 specifies both unicast and multicast datagram exchange. This
uses the Multicast Listener Discovery Protocol (MLDv2) [RFC2710]
[RFC3590] [RFC3810] [RFC4604] to enable applications to join
multicast groups, and for most applications uses Source-Specific
Multicast [RFC4607] for routing and delivery of multicast messages.
The mechanisms experimentally developed for reliable multicast in
IPv4, discussed in Section 3.2.2.3, can be used in IPv6 as well.
3.2.5.1. Protocol-Independent Multicast Routing
A multicast routing protocol has two basic functions: building the
multicast distribution tree and forwarding multicast traffic.
Multicast routing protocols generally contain a control plane for
building distribution trees, and a forwarding plane that uses the
distribution tree when forwarding multicast traffic.
The multicast model works as follows: hosts express their interest in
receiving multicast traffic from a source by sending a Join message
to their first-hop router. That router in turn sends a Join message
upstream towards the root of the tree, grafting the router (leaf
node) onto the distribution tree for the group. Data is delivered
down the tree toward the leaf nodes, which forward it onto the local
network for delivery.
The initial multicast model deployed in the Internet was known as
Any-Source Multicast (ASM). In the ASM model, any host could send to
the group and inter-domain multicast was difficult. Protocols such
as Protocol Independent Multicast - Dense Mode (PIM-DM): Protocol
Specification (Revised) [RFC3973] and Protocol Independent Multicast
- Sparse Mode (PIM-SM): Protocol Specification (Revised) [RFC4601]
were designed for the ASM model.
Many modern multicast deployments use Source-Specific Multicast (PIM-
SSM) [RFC3569][RFC4608]. In the SSM model, a host expresses interest
in a "channel", which is comprised of a source (S) and a group (G).
Distribution trees are rooted to the sending host (called an "(S,G)
tree"). Since only the source S can send on to the group, SSM has
inherent anti-jamming capability. In addition, inter-domain
multicast is simplified since finding the (S,G) channel they are
interested in receiving is the responsibility of the receivers
(rather than the networks). This implies that SSM requires some form
of directory service so that receivers can find the (S,G) channels.
Baker & Meyer Informational [Page 27]
RFC 6272 Internet Protocols for the Smart Grid June 2011
3.2.6. Adaptation to Lower-Layer Networks and Link Layer Protocols
In general, the layered architecture of the Internet enables the IPS
to run over any appropriate layer two architecture. The ability to
change the link or physical layer without having to rethink the
network layer, transports, or applications has been a great benefit
in the Internet.
Examples of link layer adaptation technology include:
Ethernet/IEEE 802.3: IPv4 has run on each link layer environment
that uses the Ethernet header (which is to say 10 and 100 MBPS
wired Ethernet, 1 and 10 GBPS wired Ethernet, and the various
versions of IEEE 802.11) using [RFC0894]. IPv6 does the same
using [RFC2464].
PPP: The IETF has defined a serial line protocol, the Point-to-Point
Protocol (PPP) [RFC1661], that uses High-Level Data Link Control
(bit-synchronous or byte synchronous) framing. The IPv4
adaptation specification is [RFC1332], and the IPv6 adaptation
specification is [RFC5072]. Current use of this protocol is in
traditional serial lines, authentication exchanges in DSL networks
using PPP Over Ethernet (PPPoE) [RFC2516], and the Digital
Signaling Hierarchy (generally referred to as Packet-on-SONET/SDH)
using PPP over SONET/SDH [RFC2615].
IEEE 802.15.4: The adaptation specification for IPv6 transmission
over IEEE 802.15.4 Networks is [RFC4944].
Numerous other adaptation specifications exist, including ATM, Frame
Relay, X.25, other standardized and proprietary LAN technologies, and
others.
3.3. Transport Layer
This section outlines the functionality of UDP, TCP, SCTP, and DCCP.
UDP and TCP are best known and most widely used in the Internet
today, while SCTP and DCCP are newer protocols that were built for
specific purposes. Other transport protocols can be built when
required.
3.3.1. User Datagram Protocol (UDP)
The User Datagram Protocol [RFC0768] and the Lightweight User
Datagram Protocol [RFC3828] are properly not "transport" protocols in
the sense of "a set of rules governing the exchange or transmission
of data electronically between devices". They are labels that
Baker & Meyer Informational [Page 28]
RFC 6272 Internet Protocols for the Smart Grid June 2011
provide for multiplexing of applications directly on the IP layer,
with transport functionality embedded in the application.
Many exchange designs have been built using UDP, and many of them
have not worked out. As a result, the use of UDP really should be
treated as designing a new transport. Advice on the use of UDP in
new applications can be found in Unicast UDP Usage Guidelines for
Application Designers [RFC5405].
Datagram Transport Layer Security [RFC5238] can be used to prevent
eavesdropping, tampering, or message forgery for applications that
run over UDP. Alternatively, UDP can run over IPsec.
3.3.2. Transmission Control Protocol (TCP)
TCP [RFC0793] is the predominant transport protocol used in the
Internet. It is "reliable", as the term is used in protocol design:
it delivers data to its peer and provides acknowledgement to the
sender, or it dies trying. It has extensions for Congestion Control
[RFC5681] and Explicit Congestion Notification [RFC3168].
The user interface for TCP is a byte stream interface -- an
application using TCP might "write" to it several times only to have
the data compacted into a common segment and delivered as such to its
peer. For message-stream interfaces, ACSE/ROSE uses the ISO
Transport Service on TCP [RFC1006][RFC2126] in the application.
Transport Layer Security [RFC5246] can be used to prevent
eavesdropping, tampering, or message forgery. Alternatively, TCP can
run over IPsec. Additionally, [RFC4987] discusses mechanisms similar
to SCTP's and DCCP's "cookie" approach that may be used to secure TCP
sessions against flooding attacks.
Finally, note that TCP has been the subject of ongoing research and
development since it was written. The Roadmap for TCP Specification
Documents [RFC4614] captures this history, and is intended to be a
guide to current and future developers in the area.
3.3.3. Stream Control Transmission Protocol (SCTP)
SCTP [RFC4960] is a more recent reliable transport protocol that can
be imagined as a TCP-like context containing multiple separate and
independent message streams (unlike TCP's byte streams). The design
of SCTP includes appropriate congestion avoidance behavior and
resistance to flooding and masquerade attacks. As it uses a message
stream interface, it may also be more appropriate for the ISO
Transport Service than using RFC 1006/2126 to turn TCP's octet
streams into a message interface.
Baker & Meyer Informational [Page 29]
RFC 6272 Internet Protocols for the Smart Grid June 2011
SCTP offers several delivery options. The basic service is
sequential non-duplicated delivery of messages within a stream, for
each stream in use. Since streams are independent, one stream may
pause due to head-of-line blocking while another stream in the same
session continues to deliver data. In addition, SCTP provides a
mechanism for bypassing the sequenced delivery service. User
messages sent using this mechanism are delivered to the SCTP user as
soon as they are received.
SCTP implements a simple "cookie" mechanism intended to limit the
effectiveness of flooding attacks by mutual authentication. This
demonstrates that the application is connected to the same peer, but
does not identify the peer. Mechanisms also exist for Dynamic
Address Reconfiguration [RFC5061], enabling peers to change addresses
during the session and yet retain connectivity. Transport Layer
Security [RFC3436] can be used to prevent eavesdropping, tampering,
or message forgery. Alternatively, SCTP can run over IPsec.
3.3.4. Datagram Congestion Control Protocol (DCCP)
DCCP [RFC4340] is an "unreliable" transport protocol (e.g., one that
does not guarantee message delivery) that provides bidirectional
unicast connections of congestion-controlled unreliable datagrams.
DCCP is suitable for applications that transfer fairly large amounts
of data and that can benefit from control over the tradeoff between
timeliness and reliability.
DCCP implements a simple "cookie" mechanism intended to limit the
effectiveness of flooding attacks by mutual authentication. This
demonstrates that the application is connected to the same peer, but
does not identify the peer. Datagram Transport Layer Security
[RFC5238] can be used to prevent eavesdropping, tampering, or message
forgery. Alternatively, DCCP can run over IPsec.
3.4. Infrastructure
3.4.1. Domain Name System
In order to facilitate network management and operations, the
Internet community has defined the Domain Name System (DNS) [RFC1034]
[RFC1035]. Names are hierarchical: a name like example.com is found
registered with a .com registrar, and within the associated network
other names like baldur.cincinatti.example.com can be defined, with
obvious hierarchy. Security extensions, which allow a registry to
sign the records it contains and in so doing demonstrate their
authenticity, are defined by the DNS Security Extensions [RFC4033]
[RFC4034] [RFC4035].
Baker & Meyer Informational [Page 30]
RFC 6272 Internet Protocols for the Smart Grid June 2011
Devices can also optionally update their own DNS record. For
example, a sensor that is using Stateless Address Autoconfiguration
[RFC4862] to create an address might want to associate it with a name
using DNS Dynamic Update [RFC2136] or DNS Secure Dynamic Update
[RFC3007].
3.4.2. Dynamic Host Configuration
As discussed in Section 3.2.2, IPv4 address assignment is generally
performed using DHCP [RFC2131]. By contrast, Section 3.2.3 points
out that IPv6 address assignment can be accomplished using either
autoconfiguration [RFC4862] [RFC4941] or DHCPv6 [RFC3315]. The best
argument for the use of autoconfiguration is a large number of
systems that require little more than a random number as an address;
the argument for DHCP is administrative control.
There are other parameters that may need to be allocated to hosts
requiring administrative configuration; examples include the
addresses of DNS servers, keys for Secure DNS, and Network Time
servers.
3.4.3. Network Time
The Network Time Protocol was originally designed by Dave Mills of
the University of Delaware and CSNET, implementing a temporal metric
in the Fuzzball Routing Protocol and generally coordinating time
experiments. The current versions of the time protocol are the
Network Time Protocol [RFC5905].
3.5. Network Management
The IETF has developed two protocols for network management: SNMP and
NETCONF. SNMP is discussed in Section 3.5.1, and NETCONF is
discussed in Section 3.5.2.
3.5.1. Simple Network Management Protocol (SNMP)
The Simple Network Management Protocol, originally specified in the
late 1980's and having passed through several revisions, is specified
in several documents:
o An Architecture for Describing Simple Network Management Protocol
(SNMP) Management Frameworks [RFC3411]
o Message Processing and Dispatching [RFC3412]
o SNMP Applications [RFC3413]
Baker & Meyer Informational [Page 31]
RFC 6272 Internet Protocols for the Smart Grid June 2011
o User-based Security Model (USM) for SNMP version 3 [RFC3414]
o View-based Access Control Model (VACM) [RFC3415]
o Version 2 of the SNMP Protocol Operations [RFC3416]
o Transport Mappings [RFC3417]
o Management Information Base (MIB) [RFC3418]
It provides capabilities for polled and event-driven activities, and
for both monitoring and configuration of systems in the field.
Historically, it has been used primarily for monitoring nodes in a
network. Messages and their constituent data are encoded using a
profile of ASN.1.
3.5.2. Network Configuration (NETCONF) Protocol
The NETCONF Configuration Protocol is specified in one basic
document, with supporting documents for carrying it over the IPS.
These documents include:
o NETCONF Configuration Protocol [RFC4741]
o Using the NETCONF Configuration Protocol over Secure SHell (SSH)
[RFC4742]
o Using NETCONF over the Simple Object Access Protocol (SOAP)
[RFC4743]
o Using the NETCONF Protocol over the Blocks Extensible Exchange
Protocol (BEEP) [RFC4744]
o NETCONF Event Notifications [RFC5277]
o NETCONF over Transport Layer Security (TLS) [RFC5539]
o Partial Lock Remote Procedure Call (RPC) for NETCONF [RFC5717]
NETCONF was developed in response to operator requests for a common
configuration protocol based on ASCII text, unlike ASN.1. In
essence, it carries XML-encoded remote procedure call (RPC) data. In
response to Smart Grid requirements, there is consideration of a
variant of the protocol that could be used for polled and event-
driven management activities, and for both monitoring and
configuration of systems in the field.
Baker & Meyer Informational [Page 32]
RFC 6272 Internet Protocols for the Smart Grid June 2011
3.6. Service and Resource Discovery
Service and resource discovery are among the most important protocols
for constrained resource self-organizing networks. These include
various sensor networks as well as the Home Area Networks (HANs),
Building Area Networks (BANs), and Field Area Networks (FANs)
envisioned by Smart Grid architects.
3.6.1. Service Discovery
Service discovery protocols are designed for the automatic
configuration and detection of devices, and the services offered by
the discovered devices. In many cases service discovery is performed
by so-called "constrained resource" devices (i.e., those with limited
processing power, memory, and power resources).
In general, service discovery is concerned with the resolution and
distribution of host names via multicast DNS [MULTICAST-DNS] and the
automatic location of network services via DHCP (Section 3.4.2), the
DNS Service Discovery (DNS-SD) [DNS-SD] (part of Apple's Bonjour
technology), and the Service Location Protocol (SLP) [RFC2608].
3.6.2. Resource Discovery
Resource Discovery is concerned with the discovery of resources
offered by end-points and is extremely important in machine-to-
machine closed-loop applications (i.e., those with no humans in the
loop). The goals of resource discovery protocols include:
o Simplicity of creation and maintenance of resources
o Commonly understood semantics
o Conformance to existing and emerging standards
o International scope and applicability
o Extensibility
o Interoperability among collections and indexing systems
The Constrained Application Protocol (CoAP) [COAP] is being developed
in IETF with these goals in mind. In particular, CoAP is designed
for use in constrained resource networks and for machine-to-machine
applications such as smart energy and building automation. It
provides a RESTful transfer protocol [RESTFUL], a built-in resource
discovery protocol, and includes web concepts such as URIs and
content-types. CoAP provides both unicast and multicast resource
Baker & Meyer Informational [Page 33]
RFC 6272 Internet Protocols for the Smart Grid June 2011
discovery and includes the ability to filter on attributes of
resource descriptions. Finally, CoAP resource discovery can also be
used to discover HTTP resources.
For simplicity, CoAP makes the assumption that all CoAP servers
listen on the default CoAP port or otherwise have been configured or
discovered using some general service discovery mechanism such as DNS
Service Discovery (DNS-SD) [DNS-SD].
Resource discovery in CoAP is accomplished through the use of well-
known resources that describe the links offered by a CoAP server.
CoAP defines a well-known URI for discovery: "/.well-known/r"
[RFC5785]. For example, the query [GET /.well-known/r] returns a
list of links (representing resources) available from the queried
CoAP server. A query such as [GET /.well-known/r?n=Voltage] returns
the resources with the name Voltage.
3.7. Other Applications
There are many applications that rely on the IP infrastructure, but
are not properly thought of as part of the IP infrastructure itself.
These applications may be useful in the context of the Smart Grid.
The choices made when constructing a profile of the Internet Profile
Suite may impact how such applications could be used. Some of them,
not by any means an exhaustive list, are discussed here.
3.7.1. Session Initiation Protocol
The Session Initiation Protocol [RFC3261] [RFC3265] [RFC3853]
[RFC4320] [RFC4916] [RFC5393] [RFC5621] is an application layer
control (signaling) protocol for creating, modifying, and terminating
multimedia sessions on the Internet, and is meant to be more scalable
than H.323. Multimedia sessions can be voice, video, instant
messaging, shared data, and/or subscriptions of events. SIP can run
on top of TCP, UDP, SCTP, or TLS over TCP. SIP is independent of the
transport layer, and independent of the underlying IPv4/v6 version.
In fact, the transport protocol used can change as the SIP message
traverses SIP entities from source to destination.
SIP itself does not choose whether a session is voice or video, nor
does it identify the actual endpoints' IP addresses. The Session
Description Protocol (SDP) [RFC4566] is intended for those purposes.
Within the SDP, which is transported by SIP, codecs are offered and
accepted (or not), and the port number and IP address at which each
endpoint wants to receive their Real-time Transport Protocol (RTP)
[RFC3550] packets are determined. The introduction of Network
Address Translation (NAT) technology into the profile, whether IPv4/
Baker & Meyer Informational [Page 34]
RFC 6272 Internet Protocols for the Smart Grid June 2011
IPv4, IPv4/IPv6 as described in Section 3.2.1.3, or IPv6/IPv6,
increases the complexity of SIP/SDP deployment. This is further
discussed in [RFC2993] and [RFC5626].
3.7.2. Extensible Messaging and Presence Protocol
The Extensible Messaging and Presence Protocol (XMPP) [RFC6120] is a
protocol for streaming Extensible Markup Language (XML) elements in
order to exchange structured information in close to real time
between any two network endpoints. Since XMPP provides a
generalized, extensible framework for exchanging XML data, it has
been proposed as an application structure for interchange between
embedded devices and sensors. It is currently used for Instant
Messaging and Presence [RFC6121] and a wide variety of real-time
communication modes. These include multi-user chat, publish-
subscribe, alerts and notifications, service discovery, multimedia
session management, device configuration, and remote procedure calls.
XMPP supports channel encryption using TLS [RFC5246] and strong
authentication (including PKIX certificate authentication) using SASL
[RFC4422]. It also makes use of Unicode-compliant addresses and
UTF-8 [RFC3629] data exchange for internationalization.
XMPP allows for End-to-End Signing and Object Encryption [RFC3923],
access to objects named using Uniform Resource Names (URN) [RFC4854],
use of Internationalized Resource Identifiers (IRIs) and Uniform
Resource Identifiers (URIs) [RFC5122], and the presentation of
Notifications [RFC5437].
3.7.3. Calendaring
Internet calendaring, as implemented in Apple iCal, Microsoft Outlook
and Entourage, and Google Calendar, is specified in Internet
Calendaring and Scheduling Core Object Specification (iCalendar)
[RFC5545] and is in the process of being updated to an XML schema in
iCalendar XML Representation [xCAL]. Several protocols exist to
carry calendar events, including the iCalendar Transport-Independent
Interoperability Protocol (iTIP) [RFC5546], the iCalendar Message-
Based Interoperability Protocol (iMIP) [RFC6047], and open source
work on the Atom Publishing Protocol [RFC5023].
4. A Simplified View of the Business Architecture
The Internet is a network of networks in which networks are
interconnected in specific ways and are independently operated. It
is important to note that the underlying Internet architecture puts
no restrictions on the ways that networks are interconnected;
interconnection is a business decision. As such, the Internet
Baker & Meyer Informational [Page 35]
RFC 6272 Internet Protocols for the Smart Grid June 2011
interconnection architecture can be thought of as a "business
structure" for the Internet.
Central to the Internet business structure are the networks that
provide connectivity to other networks, called "transit networks".
These networks sell bulk bandwidth and routing services to each other
and to other networks as customers. Around the periphery of the
transit network are companies, schools, and other networks that
provide services directly to individuals. These might generally be
divided into "enterprise networks" and "access networks"; enterprise
networks provide "free" connectivity to their own employees or
members, and also provide them a set of services including electronic
mail, web services, and so on. Access networks sell broadband
connectivity (DSL, Cable Modem, 802.11 wireless, or 3GPP wireless) or
"dial" services (including PSTN dial-up and ISDN) to subscribers.
The subscribers are typically either residential or small office/home
office (SOHO) customers. Residential customers are generally
entirely dependent on their access provider for all services, while a
SOHO buys some services from the access provider and may provide
others for itself. Networks that sell transit services to nobody
else -- SOHO, residential, and enterprise networks -- are generally
refereed to as "edge networks"; transit networks are considered to be
part of the "core" of the Internet, and access networks are between
the two. This general structure is depicted in Figure 3.
------ ------
/ \ / \
/--\ / \ / \
|SOHO|---+ Access | |Enterprise|
\--/ | Service | | Network |
/--\ | Provider| | |
|Home|---+ | ------ | |
\--/ \ +---+ +---+ /
\ / / \ \ /
------ | Transit | ------
| Service |
| Provider |
| |
\ /
\ /
------
Figure 3: Conceptual Model of Internet Businesses
Baker & Meyer Informational [Page 36]
RFC 6272 Internet Protocols for the Smart Grid June 2011
A specific example is shown in a traceroute from a home to a nearby
school. Internet connectivity in Figure 4 passes through
o the home network,
o Cox Communications, an access network using Cable Modem
technology,
o TransitRail, a commodity peering service for research and
education (R&E) networks,
o Corporation for Education Network Initiatives in California
(CENIC), a transit provider for educational networks, and
o the University of California at Santa Barbara, which in this
context might be viewed as an access network for its students and
faculty or as an enterprise network.
<stealth-10-32-244-218:> fred% traceroute www.ucsb.edu
traceroute to web.ucsb.edu (128.111.24.41),
64 hops max, 40 byte packets
1 fred-vpn (10.32.244.217) 1.560 ms 1.108 ms 1.133 ms
2 wsip-98-173-193-1.sb.sd.cox.net (98.173.193.1) 12.540 ms ...
3 68.6.13.101 ...
4 68.6.13.129 ...
5 langbbr01-as0.r2.la.cox.net ...
6 calren46-cust.lsanca01.transitrail.net ...
7 dc-lax-core1--lax-peer1-ge.cenic.net ...
8 dc-lax-agg1--lax-core1-ge.cenic.net ...
9 dc-ucsb--dc-lax-dc2.cenic.net ...
10 r2--r1--1.commserv.ucsb.edu ...
11 574-c--r2--2.commserv.ucsb.edu ...
12 * * *
Figure 4: Traceroute from Residential Customer to Educational
Institution
Another specific example could be shown in a traceroute from the home
through a Virtual Private Network (VPN tunnel) from the home,
crossing Cox Cable (an access network) and Pacific Bell (a transit
network), and terminating in Cisco Systems (an enterprise network); a
traceroute of the path doesn't show that as it is invisible within
the VPN and the contents of the VPN are invisible, due to encryption,
to the networks on the path. Instead, the traceroute in Figure 5 is
entirely within Cisco's internal network.
Baker & Meyer Informational [Page 37]
RFC 6272 Internet Protocols for the Smart Grid June 2011
<stealth-10-32-244-218:~> fred% traceroute irp-view13
traceroute to irp-view13.cisco.com (171.70.120.60),
64 hops max, 40 byte packets
1 fred-vpn (10.32.244.217) 2.560 ms 1.100 ms 1.198 ms
<tunneled path through Cox and Pacific Bell>
2 ****
3 sjc24-00a-gw2-ge2-2 (10.34.251.137) 26.298 ms...
4 sjc23-a5-gw2-g2-1 (10.34.250.78) 25.214 ms ...
5 sjc20-a5-gw1 (10.32.136.21) 23.205 ms ...
6 sjc12-abb4-gw1-t2-7 (10.32.0.189) 46.028 ms ...
7 sjc5-sbb4-gw1-ten8-2 (171.*.*.*) 26.700 ms ...
8 sjc12-dc5-gw2-ten3-1 ...
9 sjc5-dc4-gw1-ten8-1 ...
10 irp-view13 ...
Figure 5: Traceroute across VPN
Note that in both cases, the home network uses private address space
[RFC1918] while other networks generally use public address space,
and that three middleware technologies are in use here. These are
the uses of a firewall, a Network Address Translator (NAT), and a
Virtual Private Network (VPN).
Firewalls are generally sold as and considered by many to be a
security technology. This is based on the fact that a firewall
imposes a border between two administrative domains. Typically, a
firewall will be deployed between a residential, SOHO, or enterprise
network and its access or transit provider. In its essence, a
firewall is a data diode, imposing a policy on what sessions may pass
between a protected domain and the rest of the Internet. Simple
policies generally permit sessions to be originated from the
protected network but not from the outside; more complex policies may
permit additional sessions from the outside, such as electronic mail
to a mail server or a web session to a web server, and may prevent
certain applications from global access even though they are
originated from the inside.
Note that the effectiveness of firewalls remains controversial.
While network managers often insist on deploying firewalls as they
impose a boundary, others point out that their value as a security
solution is debatable. This is because most attacks come from behind
the firewall. In addition, firewalls do not protect against
application layer attacks such as viruses carried in email. Thus, as
a security solution, firewalls are justified as a layer in defense in
depth. That is, while an end system must in the end be responsible
for its own security, a firewall can inhibit or prevent certain kinds
of attacks, for example the consumption of CPU time on a critical
server.
Baker & Meyer Informational [Page 38]
RFC 6272 Internet Protocols for the Smart Grid June 2011
Key documents describing firewall technology and the issues it poses
include:
o IP Multicast and Firewalls [RFC2588]
o Benchmarking Terminology for Firewall Performance [RFC2647]
o Behavior of and Requirements for Internet Firewalls [RFC2979]
o Benchmarking Methodology for Firewall Performance [RFC3511]
o Mobile IPv6 and Firewalls: Problem Statement [RFC4487]
o NAT and Firewall Traversal Issues of Host Identity Protocol
Communication [RFC5207]
Network Address Translation is a technology that was developed in
response to ISP behaviors in the mid-1990's; when [RFC1918] was
published, many ISPs started handing out single or small numbers of
addresses, and edge networks were forced to translate. In time, this
became considered a good thing, or at least not a bad thing; it
amplified the public address space, and it was sold as if it were a
firewall. It of course is not; while traditional dynamic NATs only
translate between internal and external session address/port tuples
during the detected duration of the session, that session state may
exist in the network much longer than it exists on the end system,
and as a result constitutes an attack vector. The design, value, and
limitations of network address translation are described in:
o IP Network Address Translator Terminology and Considerations
[RFC2663]
o Traditional IP Network Address Translator [RFC3022]
o Protocol Complications with the IP Network Address Translator
[RFC3027]
o Network Address Translator Friendly Application Design Guidelines
[RFC3235]
o IAB Considerations for Network Address Translation [RFC3424]
o IPsec-Network Address Translation Compatibility Requirements
[RFC3715]
o Network Address Translation Behavioral Requirements for Unicast
UDP [RFC4787]
Baker & Meyer Informational [Page 39]
RFC 6272 Internet Protocols for the Smart Grid June 2011
o State of Peer-to-Peer Communication across Network Address
Translators [RFC5128]
o IP Multicast Requirements for a Network Address Translator and a
Network Address Port Translator [RFC5135]
Virtual Private Networks come in many forms; what they have in common
is that they are generally tunneled over the Internet backbone, so
that as in Figure 5, connectivity appears to be entirely within the
edge network although it is in fact across a service provider's
network. Examples include IPsec tunnel-mode encrypted tunnels, IP-
in-IP or GRE tunnels, and MPLS LSPs [RFC3031][RFC3032].
5. Security Considerations
Security is addressed in some detail in Section 2.2 and Section 3.1.
6. Acknowledgements
Review comments were made by Adrian Farrel, Andrew Yourtchenko, Ashok
Narayanan, Bernie Volz, Chris Lonvick, Dan Romascanu, Dave McGrew,
Dave Oran, David Harrington, David Su, Don Sturek, Francis Cleveland,
Hemant Singh, James Polk, Jari Arkko, John Meylor, Joseph Salowey,
Julien Abeille, Kerry Lynn, Lars Eggert, Magnus Westerlund, Murtaza
Chiba, Paul Duffy, Paul Hoffman, Peter Saint-Andre, Ralph Droms,
Robert Sparks, Russ White, Sean Turner, Sheila Frankel, Stephen
Farrell, Tim Polk, Toerless Eckert, Tom Herbst, Vint Cerf, and
Yoshihiro Ohba. Several of the individuals suggested text, which was
very useful, as the authors don't claim to know half as much as their
reviewers collectively do.
7. References
7.1. Normative References
[RFC1122] Braden, R., "Requirements for Internet Hosts -
Communication Layers", STD 3, RFC 1122,
October 1989.
[RFC1123] Braden, R., "Requirements for Internet Hosts -
Application and Support", STD 3, RFC 1123,
October 1989.
[RFC1812] Baker, F., "Requirements for IP Version 4 Routers",
RFC 1812, June 1995.
[RFC4294] Loughney, J., "IPv6 Node Requirements", RFC 4294,
April 2006.
Baker & Meyer Informational [Page 40]
RFC 6272 Internet Protocols for the Smart Grid June 2011
7.2. Informative References
[6LOWPAN-HC] Hui, J. and P. Thubert, "Compression Format for IPv6
Datagrams in Low Power and Lossy Networks
(6LoWPAN)", Work in Progress, February 2011.
[ABFAB-ARCH] Howlett, J., Hartman, S., Tschofenig, H., and E.
Lear, "Application Bridging for Federated Access
Beyond Web (ABFAB) Architecture", Work in Progress,
March 2011.
[AES-CCM-ECC] McGrew, D., Bailey, D., Campagna, M., and R. Dugal,
"AES-CCM ECC Cipher Suites for TLS", Work
in Progress, January 2011.
[COAP] Shelby, Z., Hartke, K., Bormann, C., and B. Frank,
"Constrained Application Protocol (CoAP)", Work
in Progress, March 2011.
[DIME-BASE] Fajardo, V., Ed., Arkko, J., Loughney, J., and G.
Zorn, "Diameter Base Protocol", Work in Progress,
January 2011.
[DNS-SD] Cheshire, S. and M. Krochmal, "DNS-Based Service
Discovery", Work in Progress, February 2011.
[DTLS] Rescorla, E. and N. Modadugu, "Datagram Transport
Layer Security version 1.2", Work in Progress,
March 2011.
[DYMO] Chakeres, I. and C. Perkins, "Dynamic MANET On-
demand (DYMO) Routing", Work in Progress, July 2010.
[IEC61850] Wikipedia, "Wikipedia Article: IEC 61850",
June 2011, <http://en.wikipedia.org/w/
index.php?title=IEC_61850&oldid=433437827>.
[IEC62351-3] International Electrotechnical Commission Technical
Committee 57, "POWER SYSTEMS MANAGEMENT AND
ASSOCIATED INFORMATION EXCHANGE. DATA AND
COMMUNICATIONS SECURITY -- Part 3: Communication
network and system security Profiles including
TCP/IP", May 2007.
[IEEE802.1X] Institute of Electrical and Electronics Engineers,
"IEEE Standard for Local and Metropolitan Area
Networks - Port based Network Access Control",
IEEE Standard 802.1X-2010, February 2010.
Baker & Meyer Informational [Page 41]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[IP-SEC] Gont, F., "Security Assessment of the Internet
Protocol Version 4", Work in Progress, April 2011.
[IPv6-NODE-REQ] Jankiewicz, E., Loughney, J., and T. Narten, "IPv6
Node Requirements", Work in Progress, May 2011.
[MULTICAST-DNS] Cheshire, S. and M. Krochmal, "Multicast DNS", Work
in Progress, February 2011.
[Model] SGIP, "Smart Grid Architecture Committee: Conceptual
Model White Paper http://collaborate.nist.gov/
twiki-sggrid/pub/SmartGrid/
SGIPConceptualModelDevelopmentSGAC/
Smart_Grid_Conceptual_Model_20100420.doc".
[OAUTHv2] Hammer-Lahav, E., Recordon, D., and D. Hardt, "The
OAuth 2.0 Authorization Protocol", Work in Progress,
May 2011.
[RESTFUL] Fielding, "Architectural Styles and the Design of
Network-based Software Architectures", 2000.
[RFC0768] Postel, J., "User Datagram Protocol", STD 6,
RFC 768, August 1980.
[RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791,
September 1981.
[RFC0792] Postel, J., "Internet Control Message Protocol",
STD 5, RFC 792, September 1981.
[RFC0793] Postel, J., "Transmission Control Protocol", STD 7,
RFC 793, September 1981.
[RFC0826] Plummer, D., "Ethernet Address Resolution Protocol:
Or converting network protocol addresses to 48.bit
Ethernet address for transmission on Ethernet
hardware", STD 37, RFC 826, November 1982.
[RFC0894] Hornig, C., "Standard for the transmission of IP
datagrams over Ethernet networks", STD 41, RFC 894,
April 1984.
[RFC1006] Rose, M. and D. Cass, "ISO transport services on top
of the TCP: Version 3", STD 35, RFC 1006, May 1987.
[RFC1034] Mockapetris, P., "Domain names - concepts and
facilities", STD 13, RFC 1034, November 1987.
Baker & Meyer Informational [Page 42]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC1035] Mockapetris, P., "Domain names - implementation and
specification", STD 13, RFC 1035, November 1987.
[RFC1058] Hedrick, C., "Routing Information Protocol",
RFC 1058, June 1988.
[RFC1112] Deering, S., "Host extensions for IP multicasting",
STD 5, RFC 1112, August 1989.
[RFC1195] Callon, R., "Use of OSI IS-IS for routing in TCP/IP
and dual environments", RFC 1195, December 1990.
[RFC1332] McGregor, G., "The PPP Internet Protocol Control
Protocol (IPCP)", RFC 1332, May 1992.
[RFC1661] Simpson, W., "The Point-to-Point Protocol (PPP)",
STD 51, RFC 1661, July 1994.
[RFC1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., Groot,
G., and E. Lear, "Address Allocation for Private
Internets", BCP 5, RFC 1918, February 1996.
[RFC1964] Linn, J., "The Kerberos Version 5 GSS-API
Mechanism", RFC 1964, June 1996.
[RFC2080] Malkin, G. and R. Minnear, "RIPng for IPv6",
RFC 2080, January 1997.
[RFC2126] Pouffary, Y. and A. Young, "ISO Transport Service on
top of TCP (ITOT)", RFC 2126, March 1997.
[RFC2131] Droms, R., "Dynamic Host Configuration Protocol",
RFC 2131, March 1997.
[RFC2136] Vixie, P., Thomson, S., Rekhter, Y., and J. Bound,
"Dynamic Updates in the Domain Name System (DNS
UPDATE)", RFC 2136, April 1997.
[RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328,
April 1998.
[RFC2357] Mankin, A., Romanov, A., Bradner, S., and V. Paxson,
"IETF Criteria for Evaluating Reliable Multicast
Transport and Application Protocols", RFC 2357,
June 1998.
[RFC2453] Malkin, G., "RIP Version 2", STD 56, RFC 2453,
November 1998.
Baker & Meyer Informational [Page 43]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol,
Version 6 (IPv6) Specification", RFC 2460,
December 1998.
[RFC2464] Crawford, M., "Transmission of IPv6 Packets over
Ethernet Networks", RFC 2464, December 1998.
[RFC2474] Nichols, K., Blake, S., Baker, F., and D. Black,
"Definition of the Differentiated Services Field (DS
Field) in the IPv4 and IPv6 Headers", RFC 2474,
December 1998.
[RFC2475] Blake, S., Black, D., Carlson, M., Davies, E., Wang,
Z., and W. Weiss, "An Architecture for
Differentiated Services", RFC 2475, December 1998.
[RFC2516] Mamakos, L., Lidl, K., Evarts, J., Carrel, D.,
Simone, D., and R. Wheeler, "A Method for
Transmitting PPP Over Ethernet (PPPoE)", RFC 2516,
February 1999.
[RFC2545] Marques, P. and F. Dupont, "Use of BGP-4
Multiprotocol Extensions for IPv6 Inter-Domain
Routing", RFC 2545, March 1999.
[RFC2560] Myers, M., Ankney, R., Malpani, A., Galperin, S.,
and C. Adams, "X.509 Internet Public Key
Infrastructure Online Certificate Status Protocol -
OCSP", RFC 2560, June 1999.
[RFC2588] Finlayson, R., "IP Multicast and Firewalls",
RFC 2588, May 1999.
[RFC2608] Guttman, E., Perkins, C., Veizades, J., and M. Day,
"Service Location Protocol, Version 2", RFC 2608,
June 1999.
[RFC2615] Malis, A. and W. Simpson, "PPP over SONET/SDH",
RFC 2615, June 1999.
[RFC2616] Fielding, R., Gettys, J., Mogul, J., Frystyk, H.,
Masinter, L., Leach, P., and T. Berners-Lee,
"Hypertext Transfer Protocol -- HTTP/1.1", RFC 2616,
June 1999.
[RFC2647] Newman, D., "Benchmarking Terminology for Firewall
Performance", RFC 2647, August 1999.
Baker & Meyer Informational [Page 44]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC2663] Srisuresh, P. and M. Holdrege, "IP Network Address
Translator (NAT) Terminology and Considerations",
RFC 2663, August 1999.
[RFC2710] Deering, S., Fenner, W., and B. Haberman, "Multicast
Listener Discovery (MLD) for IPv6", RFC 2710,
October 1999.
[RFC2743] Linn, J., "Generic Security Service Application
Program Interface Version 2, Update 1", RFC 2743,
January 2000.
[RFC2784] Farinacci, D., Li, T., Hanks, S., Meyer, D., and P.
Traina, "Generic Routing Encapsulation (GRE)",
RFC 2784, March 2000.
[RFC2865] Rigney, C., Willens, S., Rubens, A., and W. Simpson,
"Remote Authentication Dial In User Service
(RADIUS)", RFC 2865, June 2000.
[RFC2979] Freed, N., "Behavior of and Requirements for
Internet Firewalls", RFC 2979, October 2000.
[RFC2993] Hain, T., "Architectural Implications of NAT",
RFC 2993, November 2000.
[RFC3007] Wellington, B., "Secure Domain Name System (DNS)
Dynamic Update", RFC 3007, November 2000.
[RFC3022] Srisuresh, P. and K. Egevang, "Traditional IP
Network Address Translator (Traditional NAT)",
RFC 3022, January 2001.
[RFC3027] Holdrege, M. and P. Srisuresh, "Protocol
Complications with the IP Network Address
Translator", RFC 3027, January 2001.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon,
"Multiprotocol Label Switching Architecture",
RFC 3031, January 2001.
[RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
Farinacci, D., Li, T., and A. Conta, "MPLS Label
Stack Encoding", RFC 3032, January 2001.
[RFC3168] Ramakrishnan, K., Floyd, S., and D. Black, "The
Addition of Explicit Congestion Notification (ECN)
to IP", RFC 3168, September 2001.
Baker & Meyer Informational [Page 45]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC3235] Senie, D., "Network Address Translator (NAT)-
Friendly Application Design Guidelines", RFC 3235,
January 2002.
[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G.,
Johnston, A., Peterson, J., Sparks, R., Handley, M.,
and E. Schooler, "SIP: Session Initiation Protocol",
RFC 3261, June 2002.
[RFC3265] Roach, A., "Session Initiation Protocol (SIP)-
Specific Event Notification", RFC 3265, June 2002.
[RFC3275] Eastlake, D., Reagle, J., and D. Solo, "(Extensible
Markup Language) XML-Signature Syntax and
Processing", RFC 3275, March 2002.
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins,
C., and M. Carney, "Dynamic Host Configuration
Protocol for IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC3376] Cain, B., Deering, S., Kouvelas, I., Fenner, B., and
A. Thyagarajan, "Internet Group Management Protocol,
Version 3", RFC 3376, October 2002.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network
Management Protocol (SNMP) Management Frameworks",
STD 62, RFC 3411, December 2002.
[RFC3412] Case, J., Harrington, D., Presuhn, R., and B.
Wijnen, "Message Processing and Dispatching for the
Simple Network Management Protocol (SNMP)", STD 62,
RFC 3412, December 2002.
[RFC3413] Levi, D., Meyer, P., and B. Stewart, "Simple Network
Management Protocol (SNMP) Applications", STD 62,
RFC 3413, December 2002.
[RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security
Model (USM) for version 3 of the Simple Network
Management Protocol (SNMPv3)", STD 62, RFC 3414,
December 2002.
[RFC3415] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-
based Access Control Model (VACM) for the Simple
Network Management Protocol (SNMP)", STD 62,
RFC 3415, December 2002.
Baker & Meyer Informational [Page 46]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC3416] Presuhn, R., "Version 2 of the Protocol Operations
for the Simple Network Management Protocol (SNMP)",
STD 62, RFC 3416, December 2002.
[RFC3417] Presuhn, R., "Transport Mappings for the Simple
Network Management Protocol (SNMP)", STD 62,
RFC 3417, December 2002.
[RFC3418] Presuhn, R., "Management Information Base (MIB) for
the Simple Network Management Protocol (SNMP)",
STD 62, RFC 3418, December 2002.
[RFC3424] Daigle, L. and IAB, "IAB Considerations for
UNilateral Self-Address Fixing (UNSAF) Across
Network Address Translation", RFC 3424,
November 2002.
[RFC3436] Jungmaier, A., Rescorla, E., and M. Tuexen,
"Transport Layer Security over Stream Control
Transmission Protocol", RFC 3436, December 2002.
[RFC3453] Luby, M., Vicisano, L., Gemmell, J., Rizzo, L.,
Handley, M., and J. Crowcroft, "The Use of Forward
Error Correction (FEC) in Reliable Multicast",
RFC 3453, December 2002.
[RFC3511] Hickman, B., Newman, D., Tadjudin, S., and T.
Martin, "Benchmarking Methodology for Firewall
Performance", RFC 3511, April 2003.
[RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V.
Jacobson, "RTP: A Transport Protocol for Real-Time
Applications", STD 64, RFC 3550, July 2003.
[RFC3552] Rescorla, E. and B. Korver, "Guidelines for Writing
RFC Text on Security Considerations", BCP 72,
RFC 3552, July 2003.
[RFC3561] Perkins, C., Belding-Royer, E., and S. Das, "Ad hoc
On-Demand Distance Vector (AODV) Routing", RFC 3561,
July 2003.
[RFC3569] Bhattacharyya, S., "An Overview of Source-Specific
Multicast (SSM)", RFC 3569, July 2003.
[RFC3588] Calhoun, P., Loughney, J., Guttman, E., Zorn, G.,
and J. Arkko, "Diameter Base Protocol", RFC 3588,
September 2003.
Baker & Meyer Informational [Page 47]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC3590] Haberman, B., "Source Address Selection for the
Multicast Listener Discovery (MLD) Protocol",
RFC 3590, September 2003.
[RFC3626] Clausen, T. and P. Jacquet, "Optimized Link State
Routing Protocol (OLSR)", RFC 3626, October 2003.
[RFC3629] Yergeau, F., "UTF-8, a transformation format of ISO
10646", STD 63, RFC 3629, November 2003.
[RFC3715] Aboba, B. and W. Dixon, "IPsec-Network Address
Translation (NAT) Compatibility Requirements",
RFC 3715, March 2004.
[RFC3810] Vida, R. and L. Costa, "Multicast Listener Discovery
Version 2 (MLDv2) for IPv6", RFC 3810, June 2004.
[RFC3828] Larzon, L-A., Degermark, M., Pink, S., Jonsson,
L-E., and G. Fairhurst, "The Lightweight User
Datagram Protocol (UDP-Lite)", RFC 3828, July 2004.
[RFC3853] Peterson, J., "S/MIME Advanced Encryption Standard
(AES) Requirement for the Session Initiation
Protocol (SIP)", RFC 3853, July 2004.
[RFC3923] Saint-Andre, P., "End-to-End Signing and Object
Encryption for the Extensible Messaging and Presence
Protocol (XMPP)", RFC 3923, October 2004.
[RFC3971] Arkko, J., Kempf, J., Zill, B., and P. Nikander,
"SEcure Neighbor Discovery (SEND)", RFC 3971,
March 2005.
[RFC3973] Adams, A., Nicholas, J., and W. Siadak, "Protocol
Independent Multicast - Dense Mode (PIM-DM):
Protocol Specification (Revised)", RFC 3973,
January 2005.
[RFC4017] Stanley, D., Walker, J., and B. Aboba, "Extensible
Authentication Protocol (EAP) Method Requirements
for Wireless LANs", RFC 4017, March 2005.
[RFC4033] Arends, R., Austein, R., Larson, M., Massey, D., and
S. Rose, "DNS Security Introduction and
Requirements", RFC 4033, March 2005.
Baker & Meyer Informational [Page 48]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC4034] Arends, R., Austein, R., Larson, M., Massey, D., and
S. Rose, "Resource Records for the DNS Security
Extensions", RFC 4034, March 2005.
[RFC4035] Arends, R., Austein, R., Larson, M., Massey, D., and
S. Rose, "Protocol Modifications for the DNS
Security Extensions", RFC 4035, March 2005.
[RFC4108] Housley, R., "Using Cryptographic Message Syntax
(CMS) to Protect Firmware Packages", RFC 4108,
August 2005.
[RFC4120] Neuman, C., Yu, T., Hartman, S., and K. Raeburn,
"The Kerberos Network Authentication Service (V5)",
RFC 4120, July 2005.
[RFC4121] Zhu, L., Jaganathan, K., and S. Hartman, "The
Kerberos Version 5 Generic Security Service
Application Program Interface (GSS-API) Mechanism:
Version 2", RFC 4121, July 2005.
[RFC4210] Adams, C., Farrell, S., Kause, T., and T. Mononen,
"Internet X.509 Public Key Infrastructure
Certificate Management Protocol (CMP)", RFC 4210,
September 2005.
[RFC4213] Nordmark, E. and R. Gilligan, "Basic Transition
Mechanisms for IPv6 Hosts and Routers", RFC 4213,
October 2005.
[RFC4253] Ylonen, T. and C. Lonvick, "The Secure Shell (SSH)
Transport Layer Protocol", RFC 4253, January 2006.
[RFC4271] Rekhter, Y., Li, T., and S. Hares, "A Border Gateway
Protocol 4 (BGP-4)", RFC 4271, January 2006.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, February 2006.
[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, December 2005.
[RFC4302] Kent, S., "IP Authentication Header", RFC 4302,
December 2005.
[RFC4303] Kent, S., "IP Encapsulating Security Payload (ESP)",
RFC 4303, December 2005.
Baker & Meyer Informational [Page 49]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC4307] Schiller, J., "Cryptographic Algorithms for Use in
the Internet Key Exchange Version 2 (IKEv2)",
RFC 4307, December 2005.
[RFC4320] Sparks, R., "Actions Addressing Identified Issues
with the Session Initiation Protocol's (SIP) Non-
INVITE Transaction", RFC 4320, January 2006.
[RFC4340] Kohler, E., Handley, M., and S. Floyd, "Datagram
Congestion Control Protocol (DCCP)", RFC 4340,
March 2006.
[RFC4347] Rescorla, E. and N. Modadugu, "Datagram Transport
Layer Security", RFC 4347, April 2006.
[RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual
Private Networks (VPNs)", RFC 4364, February 2006.
[RFC4410] Pullen, M., Zhao, F., and D. Cohen, "Selectively
Reliable Multicast Protocol (SRMP)", RFC 4410,
February 2006.
[RFC4422] Melnikov, A. and K. Zeilenga, "Simple Authentication
and Security Layer (SASL)", RFC 4422, June 2006.
[RFC4443] Conta, A., Deering, S., and M. Gupta, "Internet
Control Message Protocol (ICMPv6) for the Internet
Protocol Version 6 (IPv6) Specification", RFC 4443,
March 2006.
[RFC4487] Le, F., Faccin, S., Patil, B., and H. Tschofenig,
"Mobile IPv6 and Firewalls: Problem Statement",
RFC 4487, May 2006.
[RFC4492] Blake-Wilson, S., Bolyard, N., Gupta, V., Hawk, C.,
and B. Moeller, "Elliptic Curve Cryptography (ECC)
Cipher Suites for Transport Layer Security (TLS)",
RFC 4492, May 2006.
[RFC4556] Zhu, L. and B. Tung, "Public Key Cryptography for
Initial Authentication in Kerberos (PKINIT)",
RFC 4556, June 2006.
[RFC4566] Handley, M., Jacobson, V., and C. Perkins, "SDP:
Session Description Protocol", RFC 4566, July 2006.
Baker & Meyer Informational [Page 50]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC4594] Babiarz, J., Chan, K., and F. Baker, "Configuration
Guidelines for DiffServ Service Classes", RFC 4594,
August 2006.
[RFC4601] Fenner, B., Handley, M., Holbrook, H., and I.
Kouvelas, "Protocol Independent Multicast - Sparse
Mode (PIM-SM): Protocol Specification (Revised)",
RFC 4601, August 2006.
[RFC4604] Holbrook, H., Cain, B., and B. Haberman, "Using
Internet Group Management Protocol Version 3
(IGMPv3) and Multicast Listener Discovery Protocol
Version 2 (MLDv2) for Source-Specific Multicast",
RFC 4604, August 2006.
[RFC4607] Holbrook, H. and B. Cain, "Source-Specific Multicast
for IP", RFC 4607, August 2006.
[RFC4608] Meyer, D., Rockell, R., and G. Shepherd, "Source-
Specific Protocol Independent Multicast in 232/8",
BCP 120, RFC 4608, August 2006.
[RFC4614] Duke, M., Braden, R., Eddy, W., and E. Blanton, "A
Roadmap for Transmission Control Protocol (TCP)
Specification Documents", RFC 4614, September 2006.
[RFC4741] Enns, R., "NETCONF Configuration Protocol",
RFC 4741, December 2006.
[RFC4742] Wasserman, M. and T. Goddard, "Using the NETCONF
Configuration Protocol over Secure SHell (SSH)",
RFC 4742, December 2006.
[RFC4743] Goddard, T., "Using NETCONF over the Simple Object
Access Protocol (SOAP)", RFC 4743, December 2006.
[RFC4744] Lear, E. and K. Crozier, "Using the NETCONF Protocol
over the Blocks Extensible Exchange Protocol
(BEEP)", RFC 4744, December 2006.
[RFC4760] Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
"Multiprotocol Extensions for BGP-4", RFC 4760,
January 2007.
[RFC4787] Audet, F. and C. Jennings, "Network Address
Translation (NAT) Behavioral Requirements for
Unicast UDP", BCP 127, RFC 4787, January 2007.
Baker & Meyer Informational [Page 51]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC4835] Manral, V., "Cryptographic Algorithm Implementation
Requirements for Encapsulating Security Payload
(ESP) and Authentication Header (AH)", RFC 4835,
April 2007.
[RFC4854] Saint-Andre, P., "A Uniform Resource Name (URN)
Namespace for Extensions to the Extensible Messaging
and Presence Protocol (XMPP)", RFC 4854,
April 2007.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H.
Soliman, "Neighbor Discovery for IP version 6
(IPv6)", RFC 4861, September 2007.
[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6
Stateless Address Autoconfiguration", RFC 4862,
September 2007.
[RFC4916] Elwell, J., "Connected Identity in the Session
Initiation Protocol (SIP)", RFC 4916, June 2007.
[RFC4919] Kushalnagar, N., Montenegro, G., and C. Schumacher,
"IPv6 over Low-Power Wireless Personal Area Networks
(6LoWPANs): Overview, Assumptions, Problem
Statement, and Goals", RFC 4919, August 2007.
[RFC4941] Narten, T., Draves, R., and S. Krishnan, "Privacy
Extensions for Stateless Address Autoconfiguration
in IPv6", RFC 4941, September 2007.
[RFC4944] Montenegro, G., Kushalnagar, N., Hui, J., and D.
Culler, "Transmission of IPv6 Packets over IEEE
802.15.4 Networks", RFC 4944, September 2007.
[RFC4960] Stewart, R., "Stream Control Transmission Protocol",
RFC 4960, September 2007.
[RFC4987] Eddy, W., "TCP SYN Flooding Attacks and Common
Mitigations", RFC 4987, August 2007.
[RFC5023] Gregorio, J. and B. de hOra, "The Atom Publishing
Protocol", RFC 5023, October 2007.
[RFC5061] Stewart, R., Xie, Q., Tuexen, M., Maruyama, S., and
M. Kozuka, "Stream Control Transmission Protocol
(SCTP) Dynamic Address Reconfiguration", RFC 5061,
September 2007.
Baker & Meyer Informational [Page 52]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC5072] Varada, S., Ed., Haskins, D., and E. Allen, "IP
Version 6 over PPP", RFC 5072, September 2007.
[RFC5122] Saint-Andre, P., "Internationalized Resource
Identifiers (IRIs) and Uniform Resource Identifiers
(URIs) for the Extensible Messaging and Presence
Protocol (XMPP)", RFC 5122, February 2008.
[RFC5128] Srisuresh, P., Ford, B., and D. Kegel, "State of
Peer-to-Peer (P2P) Communication across Network
Address Translators (NATs)", RFC 5128, March 2008.
[RFC5135] Wing, D. and T. Eckert, "IP Multicast Requirements
for a Network Address Translator (NAT) and a Network
Address Port Translator (NAPT)", BCP 135, RFC 5135,
February 2008.
[RFC5191] Forsberg, D., Ohba, Y., Patil, B., Tschofenig, H.,
and A. Yegin, "Protocol for Carrying Authentication
for Network Access (PANA)", RFC 5191, May 2008.
[RFC5207] Stiemerling, M., Quittek, J., and L. Eggert, "NAT
and Firewall Traversal Issues of Host Identity
Protocol (HIP) Communication", RFC 5207, April 2008.
[RFC5216] Simon, D., Aboba, B., and R. Hurst, "The EAP-TLS
Authentication Protocol", RFC 5216, March 2008.
[RFC5238] Phelan, T., "Datagram Transport Layer Security
(DTLS) over the Datagram Congestion Control Protocol
(DCCP)", RFC 5238, May 2008.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer
Security (TLS) Protocol Version 1.2", RFC 5246,
August 2008.
[RFC5272] Schaad, J. and M. Myers, "Certificate Management
over CMS (CMC)", RFC 5272, June 2008.
[RFC5277] Chisholm, S. and H. Trevino, "NETCONF Event
Notifications", RFC 5277, July 2008.
[RFC5280] Cooper, D., Santesson, S., Farrell, S., Boeyen, S.,
Housley, R., and W. Polk, "Internet X.509 Public Key
Infrastructure Certificate and Certificate
Revocation List (CRL) Profile", RFC 5280, May 2008.
Baker & Meyer Informational [Page 53]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC5289] Rescorla, E., "TLS Elliptic Curve Cipher Suites with
SHA-256/384 and AES Galois Counter Mode (GCM)",
RFC 5289, August 2008.
[RFC5308] Hopps, C., "Routing IPv6 with IS-IS", RFC 5308,
October 2008.
[RFC5340] Coltun, R., Ferguson, D., Moy, J., and A. Lindem,
"OSPF for IPv6", RFC 5340, July 2008.
[RFC5393] Sparks, R., Lawrence, S., Hawrylyshen, A., and B.
Campen, "Addressing an Amplification Vulnerability
in Session Initiation Protocol (SIP) Forking
Proxies", RFC 5393, December 2008.
[RFC5405] Eggert, L. and G. Fairhurst, "Unicast UDP Usage
Guidelines for Application Designers", BCP 145,
RFC 5405, November 2008.
[RFC5430] Salter, M., Rescorla, E., and R. Housley, "Suite B
Profile for Transport Layer Security (TLS)",
RFC 5430, March 2009.
[RFC5433] Clancy, T. and H. Tschofenig, "Extensible
Authentication Protocol - Generalized Pre-Shared Key
(EAP-GPSK) Method", RFC 5433, February 2009.
[RFC5437] Saint-Andre, P. and A. Melnikov, "Sieve Notification
Mechanism: Extensible Messaging and Presence
Protocol (XMPP)", RFC 5437, January 2009.
[RFC5539] Badra, M., "NETCONF over Transport Layer Security
(TLS)", RFC 5539, May 2009.
[RFC5545] Desruisseaux, B., "Internet Calendaring and
Scheduling Core Object Specification (iCalendar)",
RFC 5545, September 2009.
[RFC5546] Daboo, C., "iCalendar Transport-Independent
Interoperability Protocol (iTIP)", RFC 5546,
December 2009.
[RFC5548] Dohler, M., Watteyne, T., Winter, T., and D.
Barthel, "Routing Requirements for Urban Low-Power
and Lossy Networks", RFC 5548, May 2009.
[RFC5569] Despres, R., "IPv6 Rapid Deployment on IPv4
Infrastructures (6rd)", RFC 5569, January 2010.
Baker & Meyer Informational [Page 54]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC5621] Camarillo, G., "Message Body Handling in the Session
Initiation Protocol (SIP)", RFC 5621,
September 2009.
[RFC5626] Jennings, C., Mahy, R., and F. Audet, "Managing
Client-Initiated Connections in the Session
Initiation Protocol (SIP)", RFC 5626, October 2009.
[RFC5652] Housley, R., "Cryptographic Message Syntax (CMS)",
STD 70, RFC 5652, September 2009.
[RFC5673] Pister, K., Thubert, P., Dwars, S., and T. Phinney,
"Industrial Routing Requirements in Low-Power and
Lossy Networks", RFC 5673, October 2009.
[RFC5681] Allman, M., Paxson, V., and E. Blanton, "TCP
Congestion Control", RFC 5681, September 2009.
[RFC5717] Lengyel, B. and M. Bjorklund, "Partial Lock Remote
Procedure Call (RPC) for NETCONF", RFC 5717,
December 2009.
[RFC5740] Adamson, B., Bormann, C., Handley, M., and J.
Macker, "NACK-Oriented Reliable Multicast (NORM)
Transport Protocol", RFC 5740, November 2009.
[RFC5751] Ramsdell, B. and S. Turner, "Secure/Multipurpose
Internet Mail Extensions (S/MIME) Version 3.2
Message Specification", RFC 5751, January 2010.
[RFC5785] Nottingham, M. and E. Hammer-Lahav, "Defining Well-
Known Uniform Resource Identifiers (URIs)",
RFC 5785, April 2010.
[RFC5826] Brandt, A., Buron, J., and G. Porcu, "Home
Automation Routing Requirements in Low-Power and
Lossy Networks", RFC 5826, April 2010.
[RFC5838] Lindem, A., Mirtorabi, S., Roy, A., Barnes, M., and
R. Aggarwal, "Support of Address Families in
OSPFv3", RFC 5838, April 2010.
[RFC5849] Hammer-Lahav, E., "The OAuth 1.0 Protocol",
RFC 5849, April 2010.
Baker & Meyer Informational [Page 55]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC5867] Martocci, J., De Mil, P., Riou, N., and W.
Vermeylen, "Building Automation Routing Requirements
in Low-Power and Lossy Networks", RFC 5867,
June 2010.
[RFC5905] Mills, D., Martin, J., Burbank, J., and W. Kasch,
"Network Time Protocol Version 4: Protocol and
Algorithms Specification", RFC 5905, June 2010.
[RFC5932] Kato, A., Kanda, M., and S. Kanno, "Camellia Cipher
Suites for TLS", RFC 5932, June 2010.
[RFC5958] Turner, S., "Asymmetric Key Packages", RFC 5958,
August 2010.
[RFC5996] Kaufman, C., Hoffman, P., Nir, Y., and P. Eronen,
"Internet Key Exchange Protocol Version 2 (IKEv2)",
RFC 5996, September 2010.
[RFC5998] Eronen, P., Tschofenig, H., and Y. Sheffer, "An
Extension for EAP-Only Authentication in IKEv2",
RFC 5998, September 2010.
[RFC6031] Turner, S. and R. Housley, "Cryptographic Message
Syntax (CMS) Symmetric Key Package Content Type",
RFC 6031, December 2010.
[RFC6047] Melnikov, A., "iCalendar Message-Based
Interoperability Protocol (iMIP)", RFC 6047,
December 2010.
[RFC6052] Bao, C., Huitema, C., Bagnulo, M., Boucadair, M.,
and X. Li, "IPv6 Addressing of IPv4/IPv6
Translators", RFC 6052, October 2010.
[RFC6090] McGrew, D., Igoe, K., and M. Salter, "Fundamental
Elliptic Curve Cryptography Algorithms", RFC 6090,
February 2011.
[RFC6120] Saint-Andre, P., "Extensible Messaging and Presence
Protocol (XMPP): Core", RFC 6120, March 2011.
[RFC6121] Saint-Andre, P., "Extensible Messaging and Presence
Protocol (XMPP): Instant Messaging and Presence",
RFC 6121, March 2011.
[RFC6144] Baker, F., Li, X., Bao, C., and K. Yin, "Framework
for IPv4/IPv6 Translation", RFC RFC6144, April 2011.
Baker & Meyer Informational [Page 56]
RFC 6272 Internet Protocols for the Smart Grid June 2011
[RFC6145] Li, X., Bao, C., and F. Baker, "IP/ICMP Translation
Algorithm", RFC 6145, April 2011.
[RFC6146] Bagnulo, M., Matthews, P., and I. Beijnum, "Stateful
NAT64: Network Address and Protocol Translation from
IPv6 Clients to IPv4 Servers", RFC 6146, April 2011.
[RFC6147] Bagnulo, M., Sullivan, A., Matthews, P., and I.
Beijnum, "DNS64: DNS Extensions for Network Address
Translation from IPv6 Clients to IPv4 Servers",
RFC 6147, April 2011.
[RFC6180] Arkko, J. and F. Baker, "Guidelines for Using IPv6
Transition Mechanisms during IPv6 Deployment",
RFC 6180, May 2011.
[RPL] Winter, T., Thubert, P., Brandt, A., Clausen, T.,
Hui, J., Kelsey, R., Levis, P., Pister, K., Struik,
R., and J. Vasseur, "RPL: IPv6 Routing Protocol for
Low power and Lossy Networks", Work in Progress,
March 2011.
[SP-MULPIv3.0] CableLabs, "DOCSIS 3.0 MAC and Upper Layer Protocols
Interface Specification, CM-SP-MULPIv3.0-I10-
090529", May 2009.
[SmartGrid] Wikipedia, "Wikipedia Article: Smart Grid",
February 2011, <http://en.wikipedia.org/w/
index.php?title=Smart_grid&oldid=415838933>.
[TCP-SEC] Gont, F., "Security Assessment of the Transmission
Control Protocol (TCP)", Work in Progress,
January 2011.
[r1822] Bolt Beranek and Newman Inc., "Interface Message
Processor -- Specifications for the interconnection
of a host and a IMP, Report No. 1822", January 1976.
[xCAL] Daboo, C., Douglass, M., and S. Lees, "xCal: The XML
format for iCalendar", Work in Progress, April 2011.
Baker & Meyer Informational [Page 57]
RFC 6272 Internet Protocols for the Smart Grid June 2011
Appendix A. Example: Advanced Metering Infrastructure
This appendix provides a worked example of the use of the Internet
Protocol Suite in a network such as the Smart Grid's Advanced
Metering Infrastructure (AMI). There are several possible models.
Figure 6 shows the structure of the AMI as it reaches out towards a
set of residences. In this structure, we have the home itself and
its Home Area Network (HAN), the Neighborhood Area Network (NAN) that
the utility uses to access the meter at the home, and the utility
access network that connects a set of NANs to the utility itself.
For the purposes of this discussion, assume that the NAN contains a
distributed application in a set collectors, which is of course only
one way the application could be implemented.
---
A thermostats, appliances, etc
| ------+-----------------------------------
| |
|"HAN" | <--- Energy Services Interface (ESI)
| +---+---+
| | Meter | Meter is generally an ALG between the AMI and the HAN
| +---+---+
V \
--- \
A \ | /
| \ | /
| "NAN" +--+-+-+---+ Likely a router but could
| |Collector | be a front-end application
V +----+-----+ gateway for utility
--- \
A \ | /
| \ | /
|"AMI" +--+-+-+--+
| | AMI |
| | Headend |
V +---------+
---
Figure 6: The HAN, NAN, and Utility in the Advanced Metering
Infrastructure
There are several questions that have to be answered in describing
this picture, which given possible answers yield different possible
models. They include at least:
o How does Demand Response work? Either:
Baker & Meyer Informational [Page 58]
RFC 6272 Internet Protocols for the Smart Grid June 2011
* The utility presents pricing signals to the home,
* The utility presents pricing signals to individual devices
(e.g., a Pluggable Electric Vehicle),
* The utility adjusts settings on individual appliances within
the home.
o How does the utility access meters at the home?
* The AMI Headend manages the interfaces with the meters,
collecting metering data and passing it on to the appropriate
applications over the Enterprise Bus, or
* Distributed application support ("collectors") might access and
summarize the information; this device might be managed by the
utility or by a service between the utility and its customers.
In implementation, these models are idealized; reality may include
some aspects of each model in specified cases.
The examples include:
1. Appendix A.2 presumes that the HAN, the NAN, and the utility's
network are separate administrative domains and speak application
to application across those domains.
2. Appendix A.3 repeats the first example, but presuming that the
utility directly accesses appliances within the HAN from the
collector.
3. Appendix A.4 repeats the first example, but presuming that the
collector directly forwards traffic as a router in addition to
distributed application chores. Note that this case implies
numerous privacy and security concerns and as such is considered
a less likely deployment model.
A.1. How to Structure a Network
A key consideration in the Internet has been the development of new
link layer technologies over time. The ARPANET originally used a BBN
proprietary link layer called BBN 1822 [r1822]. In the late 1970's,
the ARPANET switched to X.25 as an interface to the 1822 network.
With the deployment of the IEEE 802 series technologies in the early
1980's, IP was deployed on Ethernet (IEEE 802.3), Token Ring (IEEE
802.5) and WiFi (IEEE 802.11), as well as Arcnet, serial lines of
various kinds, Frame Relay, and ATM. A key issue in this evolution
was that the applications developed to run on the Internet use APIs
Baker & Meyer Informational [Page 59]
RFC 6272 Internet Protocols for the Smart Grid June 2011
related to the IPS, and as a result require little or no change to
continue operating in a new link layer architecture or a mixture of
them.
The Smart Grid is likely to see a similar evolution over time.
Consider the Home Area Network (HAN) as a readily understandable
small network. At this juncture, technologies proposed for
residential networks include IEEE P1901, various versions of IEEE
802.15.4, and IEEE 802.11. It is reasonable to expect other
technologies to be developed in the future. As the Zigbee Alliance
has learned (and as a resulted incorporated the IPS in Smart Energy
Profile 2.0), there is significant value in providing a virtual
address that is mapped to interfaces or nodes attached to each of
those technologies.
Baker & Meyer Informational [Page 60]
RFC 6272 Internet Protocols for the Smart Grid June 2011
Utility NAN
/
/
+----+-----+ +--+ +--+ +--+
| Meter | |D1| |D2| |D3|
+-----+----+ ++-+ ++-+ ++-+
| | | |
----+-+-------+----+----+---- IEEE 802.15.4
|
+--+---+
|Router+------/------ Residential Broadband
+--+---+
|
----+---------+----+----+---- IEEE P1901
| | |
++-+ ++-+ ++-+
|D4| |D5| |D6|
+--+ +--+ +--+
A thermostats, appliances, etc
| ------+----------------+------------------
|"HAN" | |
| +---+---+ +---+---+
| |Router | | Meter |
| |or EMS | | |
V +---+---+ +---+---+
--- | --- \
| ^ \ | /
| |"NAN" \ | /
---+--- | +--+-+-+---+
/ \ | |"Pole Top"|
| Internet| v +----+-----+
\ / ---
-------
Figure 7: Two Views of a Home Area Network
There are two possible communication models within the HAN, both of
which are likely to be useful. Devices may communicate directly with
each other, or they may be managed by some central controller. An
example of direct communications might be a light switch that
directly commands a lamp to turn on or off. An example of indirect
communications might be a control application in a Customer or
Building that accepts telemetry from a thermostat, applies some form
of policy, and controls the heating and air conditioning systems. In
addition, there are high-end appliances in the market today that use
residential broadband to communicate with their manufacturers, and
obviously the meter needs to communicate with the utility.
Baker & Meyer Informational [Page 61]
RFC 6272 Internet Protocols for the Smart Grid June 2011
Figure 7 shows two simple networks, one of which uses IEEE 802.15.4
and IEEE 1901 domains, and one of which uses an arbitrary LAN within
the home, which could be IEEE 802.3/Ethernet, IEEE 802.15.4, IEEE
1901, IEEE 802.11, or anything else that made sense in context. Both
show the connectivity between them as a router separate from the
energy management system (EMS). This is for clarity; the two could
of course be incorporated into a single system, and one could imagine
appliances that want to communicate with their manufacturers
supporting both a HAN interface and a WiFi interface rather than
depending on the router. These are all manufacturer design
decisions.
A.1.1. HAN Routing
The HAN can be seen as communicating with two kinds of non-HAN
networks. One is the home LAN, which may in turn be attached to the
Internet, and will generally either derive its prefix from the
upstream ISP or use a self-generated Unique Local Addressing (ULA).
Another is the utility's NAN, which through an ESI provides utility
connectivity to the HAN; in this case the HAN will be addressed by a
self-generated ULA (note, however, that in some cases ESI may also
provide a prefix via DHCP [RFC3315]). In addition, the HAN will have
link-local addresses that can be used between neighboring nodes. In
general, an HAN will be comprised of both 802.15.4, 802.11, and
possibly other networks.
The ESI is a node on the user's residential network, and will not
typically provide stateful packet forwarding or firewall services
between the HAN and the utility network(s). In general, the ESI is a
node on the home network; in some cases, the meter may act as the
ESI. However, the ESI must be capable of understanding that most
home networks are not 802.15.4 enabled (rather, they are typically
802.11 networks), and that it must be capable of setting up ad hoc
networks between various sensors in the home (e.g., between the meter
and say, a thermostat) in the event there aren't other networks
available.
A.1.2. HAN Security
In any network, we have a variety of threats and a variety of
possible mitigations. These include, at minimum:
Link Layer: Why is your machine able to talk in my network? The
WiFi SSIDs often use some form of authenticated access control,
which may be a simple encrypted password mechanism or may use a
combination of encryption and IEEE 802.1X+EAP-TLS Authentication/
Baker & Meyer Informational [Page 62]
RFC 6272 Internet Protocols for the Smart Grid June 2011
Authorization to ensure that only authorized communicants can use
it. If a LAN has a router attached, the router may also implement
a firewall to filter remote accesses.
Network Layer: Given that your machine is authorized access to my
network, why is your machine talking with my machine? IPsec is a
way of ensuring that computers that can use a network are allowed
to talk with each other, may also enforce confidentiality, and may
provide VPN services to make a device or network appear to be part
of a remote network.
Application: Given that your machine is authorized access to my
network and my machine, why is your application talking with my
application? The fact that your machine and mine are allowed to
talk for some applications doesn't mean they are allowed to for
all applications. (D)TLS, https, and other such mechanisms enable
an application to impose application-to-application controls
similar to the network layer controls provided by IPsec.
Remote Application: How do I know that the data I received is the
data you sent? Especially in applications like electronic mail,
where data passes through a number of intermediaries that one may
or may not really want munging it (how many times have you seen a
URL broken by a mail server?), we have tools (DKIM, S/MIME, and
W3C XML Signatures to name a few) to provide non-repudiability and
integrity verification. This may also have legal ramifications:
if a record of a meter reading is to be used in billing, and the
bill is disputed in court, one could imagine the court wanting
proof that the record in fact came from that meter at that time
and contained that data.
Application-specific security: In addition, applications often
provide security services of their own. The fact that I can
access a file system, for example, doesn't mean that I am
authorized to access everything in it; the file system may well
prevent my access to some of its contents. Routing protocols like
BGP are obsessed with the question "what statements that my peer
made am I willing to believe", and monitoring protocols like SNMP
may not be willing to answer every question they are asked,
depending on access configuration.
Devices in the HAN want controlled access to the LAN in question for
obvious reasons. In addition, there should be some form of mutual
authentication between devices -- the lamp controller will want to
know that the light switch telling it to change state is the right
light switch, for example. The EMS may well want strong
authentication of accesses -- the parents may not want the children
Baker & Meyer Informational [Page 63]
RFC 6272 Internet Protocols for the Smart Grid June 2011
changing the settings, and while the utility and the customer are
routinely granted access, other parties (especially parties with
criminal intent) need to be excluded.
A.2. Model 1: AMI with Separated Domains
With the background given in Appendix A.1, we can now discuss the use
of IP (IPv4 or IPv6) in the AMI.
In this first model, consider the three domains in Figure 6 to
literally be separate administrative domains, potentially operated by
different entities. For example, the NAN could be a WiMAX network
operated by a traditional telecom operator, the utility's network
(including the collector) is its own, and the residential network is
operated by the resident. In this model, while communications
between the collector and the Meter are normal, the utility has no
other access to appliances in the home, and the collector doesn't
directly forward messages from the NAN upstream.
In this case, as shown in Figure 7, it would make the most sense to
design the collector, the Meter, and the EMS as hosts on the NAN --
design them as systems whose applications can originate and terminate
exchanges or sessions in the NAN, but not forward traffic from or to
other devices.
In such a configuration, Demand Response has to be performed by
having the EMS accept messages such as price signals from the "pole
top", apply some form of policy, and then orchestrate actions within
the home. Another possibility is to have the EMS communicate with
the ESI located in the meter. If the thermostat has high demand and
low demand (day/night or morning/day/evening/night) settings, Demand
Response might result in it moving to a lower demand setting, and the
EMS might also turn off specified circuits in the home to diminish
lighting.
In this scenario, Quality of Service (QoS) issues reportedly arise
when high precedence messages must be sent through the collector to
the home; if the collector is occupied polling the meters or doing
some other task, the application may not yield control of the
processor to the application that services the message. Clearly,
this is either an application or an Operating System problem;
applications need to be designed in a manner that doesn't block high
precedence messages. The collector also needs to use appropriate NAN
services, if they exist, to provide the NAN QoS it needs. For
example, if WiMax is in use, it might use a routine-level service for
normal exchanges but a higher precedence service for these messages.
Baker & Meyer Informational [Page 64]
RFC 6272 Internet Protocols for the Smart Grid June 2011
A.3. Model 2: AMI with Neighborhood Access to the Home
In this second model, let's imagine that the utility directly
accesses appliances within the HAN. Rather than expect an EMS to
respond to price signals in Demand Response, it directly commands
devices like air conditioners to change state, or throws relays on
circuits to or within the home.
+----------+ +--+ +--+ +--+
| Meter | |D1| |D2| |D3|
+-----+----+ ++-+ ++-+ ++-+
| | | |
----+-+-------+----+----+---- IEEE 802.15.4
|
+--+---+
| +------/------ NAN
|Router|
| +------/------ Residential Broadband
+--+---+
|
----+--+------+----+----+---- IEEE P1901
| | | |
+-+-+ ++-+ ++-+ ++-+
|EMS| |D4| |D5| |D6|
+---+ +--+ +--+ +--+
Figure 8: Home Area Network
In this case, as shown in Figure 8, the Meter and EMS act as hosts on
the HAN, and there is a router between the HAN and the NAN.
As one might imagine, there are serious security considerations in
this model. Traffic between the NAN and the residential broadband
network should be filtered, and the issues raised in Appendix A.1.2
take on a new level of meaning. One of the biggest threats may be a
legal or at least a public relations issue; if the utility
intentionally disables a circuit in a manner or at a time that
threatens life (the resident's kidney dialysis machine is on it, or a
respirator, for example), the matter might make the papers.
Unauthorized access could be part of juvenile pranks or other things
as well. So one really wants the appliances to only obey commands
under strict authentication/authorization controls.
In addition to the QoS issues raised in Appendix A.2, there is the
possibility of queuing issues in the router. In such a case, the IP
datagrams should probably use the Low-Latency Data Service Class
Baker & Meyer Informational [Page 65]
RFC 6272 Internet Protocols for the Smart Grid June 2011
described in [RFC4594], and let other traffic use the Standard
Service Class or other service classes.
A.4. Model 3: Collector Is an IP Router
In this third model, the relationship between the NAN and the HAN is
either as in Appendix A.2 or Appendix A.3; what is different is that
the collector may be an IP router. In addition to whatever
autonomous activities it is doing, it forwards traffic as an IP
router in some cases.
Analogous to Appendix A.3, there are serious security considerations
in this model. Traffic being forwarded should be filtered, and the
issues raised in Appendix A.1.2 take on a new level of meaning -- but
this time at the utility mainframe. Unauthorized access is likely
similar to other financially-motivated attacks that happen in the
Internet, but presumably would be coming from devices in the HAN that
have been co-opted in some way. One really wants the appliances to
only obey commands under strict authentication/authorization
controls.
In addition to the QoS issues raised in Appendix A.2, there is the
possibility of queuing issues in the collector. In such a case, the
IP datagrams should probably use the Low-Latency Data Service Class
described in [RFC4594], and let other traffic use the Standard
Service Class or other service classes.
Authors' Addresses
Fred Baker
Cisco Systems
Santa Barbara, California 93117
USA
EMail: fred@cisco.com
David Meyer
Cisco Systems
Eugene, Oregon 97403
USA
EMail: dmm@cisco.com
Baker & Meyer Informational [Page 66]