💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc5157.txt captured on 2023-12-28 at 17:40:04.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group T. Chown
Request for Comments: 5157 University of Southampton
Category: Informational March 2008
IPv6 Implications for Network Scanning
Status of This Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Abstract
The much larger default 64-bit subnet address space of IPv6 should in
principle make traditional network (port) scanning techniques used by
certain network worms or scanning tools less effective. While
traditional network scanning probes (whether by individuals or
automated via network worms) may become less common, administrators
should be aware that attackers may use other techniques to discover
IPv6 addresses on a target network, and thus they should also be
aware of measures that are available to mitigate them. This
informational document discusses approaches that administrators could
take when planning their site address allocation and management
strategies as part of a defence-in-depth approach to network
security.
Chown Informational [Page 1]
RFC 5157 IPv6 Network Scanning March 2008
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Target Address Space for Network Scanning . . . . . . . . . . 4
2.1. IPv4 . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2. IPv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3. Reducing the IPv6 Search Space . . . . . . . . . . . . . . 4
2.4. Dual-Stack Networks . . . . . . . . . . . . . . . . . . . 5
2.5. Defensive Scanning . . . . . . . . . . . . . . . . . . . . 5
3. Alternatives for Attackers: Off-Link . . . . . . . . . . . . . 5
3.1. Gleaning IPv6 Prefix Information . . . . . . . . . . . . . 5
3.2. DNS Advertised Hosts . . . . . . . . . . . . . . . . . . . 6
3.3. DNS Zone Transfers . . . . . . . . . . . . . . . . . . . . 6
3.4. Log File Analysis . . . . . . . . . . . . . . . . . . . . 6
3.5. Application Participation . . . . . . . . . . . . . . . . 6
3.6. Multicast Group Addresses . . . . . . . . . . . . . . . . 7
3.7. Transition Methods . . . . . . . . . . . . . . . . . . . . 7
4. Alternatives for Attackers: On-Link . . . . . . . . . . . . . 7
4.1. General On-Link Methods . . . . . . . . . . . . . . . . . 7
4.2. Intra-Site Multicast or Other Service Discovery . . . . . 8
5. Tools to Mitigate Scanning Attacks . . . . . . . . . . . . . . 8
5.1. IPv6 Privacy Addresses . . . . . . . . . . . . . . . . . . 9
5.2. Cryptographically Generated Addresses (CGAs) . . . . . . . 9
5.3. Non-Use of MAC Addresses in EUI-64 Format . . . . . . . . 10
5.4. DHCP Service Configuration Options . . . . . . . . . . . . 10
6. Conclusions . . . . . . . . . . . . . . . . . . . . . . . . . 10
7. Security Considerations . . . . . . . . . . . . . . . . . . . 10
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 11
9. Informative References . . . . . . . . . . . . . . . . . . . . 11
Chown Informational [Page 2]
RFC 5157 IPv6 Network Scanning March 2008
1. Introduction
One of the key differences between IPv4 and IPv6 is the much larger
address space for IPv6, which also goes hand-in-hand with much larger
subnet sizes. This change has a significant impact on the
feasibility of TCP and UDP network scanning, whereby an automated
process is run to detect open ports (services) on systems that may
then be subject to a subsequent attack. Today many IPv4 sites are
subjected to such probing on a recurring basis. Such probing is
common in part due to the relatively dense population of active hosts
in any given chunk of IPv4 address space.
The 128 bits of IPv6 [1] address space is considerably bigger than
the 32 bits of address space in IPv4. In particular, the IPv6
subnets to which hosts attach will by default have 64 bits of host
address space [2]. As a result, traditional methods of remote TCP or
UDP network scanning to discover open or running services on a host
will potentially become less feasible, due to the larger search space
in the subnet. Similarly, worms that rely on off-link network
scanning to propagate may also potentially be more limited in impact.
This document discusses this property of IPv6 and describes related
issues for IPv6 site network administrators to consider, which may be
useful when planning site address allocation and management
strategies.
For example, many worms, like Slammer, rely on such address scanning
methods to propagate, whether they pick subnets numerically (and thus
probably topologically) close to the current victim, or subnets in
random remote networks. The nature of these worms may change, if
detection of target hosts between sites or subnets is harder to
achieve by traditional methods. However, there are other worms that
propagate via methods such as email, for which the methods discussed
in this text are not relevant.
It must be remembered that the defence of a network must not rely
solely on the unpredictable sparseness of the host addresses on that
network. Such a feature or property is only one measure in a set of
measures that may be applied. This document discusses various
measures that can be used by a site to mitigate attacks as part of an
overall strategy. Some of these have a lower cost to deploy than
others. For example, if numbering hosts on a subnet, it may be as
cheap to number hosts without any predictable pattern as it is to
number them sequentially. In contrast, use of IPv6 privacy
extensions [3] may complicate network management (identifying which
hosts use which addresses).
Chown Informational [Page 3]
RFC 5157 IPv6 Network Scanning March 2008
This document complements the transition-centric discussion of the
issues that can be found in Appendix A of "IPv6 Transition/
Co-existence Security Considerations" [12], which takes a broad view
of security issues for transitioning networks. The reader is also
referred to a recent paper by Bellovin on network worm propagation
strategies in IPv6 networks [13]. This paper discusses some of the
issues included in this document, from a slightly different
perspective.
2. Target Address Space for Network Scanning
There are significantly different considerations for the feasibility
of plain, brute-force IPv4 and IPv6 address scanning.
2.1. IPv4
A typical IPv4 subnet may have 8 bits reserved for host addressing.
In such a case, a remote attacker need only probe at most 256
addresses to determine if a particular service is running publicly on
a host in that subnet. Even at only one probe per second, such a
scan would take under 5 minutes to complete.
2.2. IPv6
A typical IPv6 subnet will have 64 bits reserved for host addressing.
In such a case, a remote attacker in principle needs to probe 2^64
addresses to determine if a particular open service is running on a
host in that subnet. At a very conservative one probe per second,
such a scan may take some 5 billion years to complete. A more rapid
probe will still be limited to (effectively) infinite time for the
whole address space. However, there are ways for the attacker to
reduce the address search space to scan against within the target
subnet, as we discuss below.
2.3. Reducing the IPv6 Search Space
The IPv6 host address space through which an attacker may search can
be reduced in at least two ways.
First, the attacker may rely on the administrator conveniently
numbering their hosts from [prefix]::1 upward. This makes scanning
trivial, and thus should be avoided unless the host's address is
readily obtainable from other sources (for example, it is the site's
published primary DNS or email Mail Exchange (MX) server).
Alternatively, if hosts are numbered sequentially, or using any
regular scheme, knowledge of one address may expose other available
addresses to scan.
Chown Informational [Page 4]
RFC 5157 IPv6 Network Scanning March 2008
Second, in the case of statelessly autoconfiguring [1] hosts, the
host part of the address will usually take a well-known format that
includes the Ethernet vendor prefix and the "fffe" stuffing. For
such hosts, the search space can be reduced to 48 bits. Further, if
the Ethernet vendor is also known, the search space may be reduced to
24 bits, with a one probe per second scan then taking a less daunting
194 days. Even where the exact vendor is not known, using a set of
common vendor prefixes can reduce the search. In addition, many
nodes in a site network may be procured in batches, and thus have
sequential or near sequential Media Access Control (MAC) addresses;
if one node's autoconfigured address is known, scanning around that
address may yield results for the attacker. Again, any form of
sequential host addressing should be avoided if possible.
2.4. Dual-Stack Networks
Full advantage of the increased IPv6 address space in terms of
resilience to network scanning may not be gained until IPv6-only
networks and devices become more commonplace, given that most IPv6
hosts are currently dual stack, with (more readily scannable) IPv4
connectivity. However, many applications or services (e.g., new
peer-to-peer applications) on the (dual-stack) hosts may emerge that
are only accessible over IPv6, and that thus can only be discovered
by IPv6 address scanning.
2.5. Defensive Scanning
The problem faced by the attacker for an IPv6 network is also faced
by a site administrator looking for vulnerabilities in their own
network's systems. The administrator should have the advantage of
being on-link for scanning purposes though.
3. Alternatives for Attackers: Off-Link
If IPv6 hosts in subnets are allocated addresses 'randomly', and as a
result IPv6 network scanning becomes relatively infeasible, attackers
will need to find new methods to identify IPv6 addresses for
subsequent scanning. In this section, we discuss some possible paths
attackers may take. In these cases, the attacker will attempt to
identify specific IPv6 addresses for subsequent targeted probes.
3.1. Gleaning IPv6 Prefix Information
Note that in IPv6, an attacker would not be able to search across the
entire IPv6 address space as they might in IPv4. An attacker may
learn general prefixes to focus their efforts on by observing route
view information (e.g., from public looking-glass services) or
information on allocated address space from Regional Internet
Chown Informational [Page 5]
RFC 5157 IPv6 Network Scanning March 2008
Registries (RIRs). In general, this would only yield information at
most at the /48 prefix granularity, though some specific /64 prefixes
may be observed from route views on some parts of some networks.
3.2. DNS Advertised Hosts
Any servers that are DNS listed, e.g., MX mail relays, or web
servers, will remain open to probing from the very fact that their
IPv6 addresses will be published in the DNS.
While servers are relatively easy to find because they are DNS-
published, any systems that are not DNS-published will be much harder
to locate via traditional scanning than is the case for IPv4
networks. It is worth noting that where a site uses sequential host
numbering, publishing just one address may lead to a threat upon the
other hosts.
3.3. DNS Zone Transfers
In the IPv6 world, a DNS zone transfer is much more likely to narrow
the number of hosts an attacker needs to target. This implies that
restricting zone transfers is (more) important for IPv6, even if it
is already good practice to restrict them in the IPv4 world.
There are some projects that provide Internet mapping data from
access to such transfers. Administrators may of course agree to
provide such transfers where they choose to do so.
3.4. Log File Analysis
IPv6 addresses may be harvested from recorded logs, such as web site
logs. Anywhere else where IPv6 addresses are explicitly recorded may
prove a useful channel for an attacker, e.g., by inspection of the
(many) Received from: or other header lines in archived email or
Usenet news messages.
3.5. Application Participation
More recent peer-to-peer applications often include some centralised
server that coordinates the transfer of data between peers. The
BitTorrent application builds swarms of nodes that exchange chunks of
files, with a tracker passing information about peers with available
chunks of data between the peers. Such applications may offer an
attacker a source of peer IP addresses to probe.
Chown Informational [Page 6]
RFC 5157 IPv6 Network Scanning March 2008
3.6. Multicast Group Addresses
Where an Embedded Rendezvous Point (RP) [7] multicast group address
is known, the unicast address of the RP is implied by the group
address. Where unicast-prefix-based multicast group addresses [5]
are used, specific /64 link prefixes may also be disclosed in traffic
that goes off-site. An administrator may thus choose to put aside
/64 bit prefixes for multicast group addresses that are not in use
for normal unicast routing and addressing. Alternatively, a site may
simply use their non-specific /48 site prefix allocation to generate
RFC3306 multicast group addresses.
3.7. Transition Methods
Specific knowledge of the target network may be gleaned if that
attacker knows it is using 6to4 [4], ISATAP [10], Teredo [11], or
other techniques that derive low-order bits from IPv4 addresses
(though in this case, unless they are using IPv4 NAT, the IPv4
addresses may be probed anyway).
For example, the current Microsoft 6to4 implementation uses the
address 2002:V4ADDR::V4ADDR while older Linux and FreeBSD
implementations default to 2002:V4ADDR::1. This leads to specific
knowledge of specific hosts in the network. Given one host in the
network is observed as using a given transition technique, it is
likely that there are more.
In the case of Teredo, the 64-bit node identifier is generated from
the IPv4 address observed at a Teredo server along with a UDP port
number. The Teredo specification also allows for discovery of other
Teredo clients on the same IPv4 subnet via a well-known IPv4
multicast address (see Section 2.17 of RFC 4380 [11]).
4. Alternatives for Attackers: On-Link
The main thrust of this text is considerations for off-link attackers
or probing of a network. In general, once one host on a link is
compromised, others on the link can be very readily discovered.
4.1. General On-Link Methods
If the attacker already has access to a system on the current subnet,
then traffic on that subnet, be it Neighbour Discovery or
application-based traffic, can invariably be observed, and active
node addresses within the local subnet learnt.
Chown Informational [Page 7]
RFC 5157 IPv6 Network Scanning March 2008
In addition to making observations of traffic on the link, IPv6-
enabled hosts on local subnets may be discovered through probing the
"all hosts" link-local multicast address. Likewise, any routers on
the subnet may be found via the "all routers" link-local multicast
address. An attacker may choose to probe in a slightly more
obfuscated way by probing the solicited node multicast address of a
potential target host.
Where a host has already been compromised, its Neighbour Discovery
cache is also likely to include information about active nodes on the
current subnet, just as an ARP cache would do for IPv4.
Also, depending on the node, traffic to or from other nodes (in
particular, server systems) is likely to show up if an attacker can
gain a presence on a node in any one subnet in a site's network.
4.2. Intra-Site Multicast or Other Service Discovery
A site may also have site- or organisational-scope multicast
configured, in which case application traffic, or service discovery,
may be exposed site wide. An attacker may also choose to use any
other service discovery methods supported by the site.
5. Tools to Mitigate Scanning Attacks
There are some tools that site administrators can apply to make the
task for IPv6 network scanning attackers harder. These methods arise
from the considerations in the previous section.
The author notes that at his current (university) site, there is no
evidence of general network scanning running across subnets.
However, there is network scanning over IPv6 connections to systems
whose IPv6 addresses are advertised (DNS servers, MX relays, web
servers, etc.), which are presumably looking for other open ports on
these hosts to probe further. At the time of writing, DHCPv6 [6] is
not yet in use at the author's site, and clients use stateless
autoconfiguration. Therefore, the author's site does not yet have
sequentially numbered client hosts deployed as may typically be seen
in today's IPv4 DHCP-served networks.
Chown Informational [Page 8]
RFC 5157 IPv6 Network Scanning March 2008
5.1. IPv6 Privacy Addresses
Hosts in a network using IPv6 privacy extensions [3] will typically
only connect to external systems using their current (temporary)
privacy address. The precise behaviour of a host with a stable
global address and one or more dynamic privacy address(es) when
selecting a source address to use may be operating-system-specific,
or configurable, but typical behaviour when initiating a connection
is use of a privacy address when available.
While an attacker may be able to port scan a privacy address, if they
do so quickly upon observing or otherwise learning of the address,
the threat or risk is reduced due to the time-constrained value of
the address. One implementation of RFC 4941 already deployed has
privacy addresses active (used by the node) for one day, with such
addresses reachable for seven days.
Note that an RFC 4941 host will usually also have a separate static
global IPv6 address by which it can also be reached, and that may be
DNS-advertised if an externally reachable service is running on it.
DHCPv6 can be used to serve normal global addresses and IPv6 privacy
addresses.
The implication is that while privacy addresses can mitigate the
long-term value of harvested addresses, an attacker creating an IPv6
application server to which clients connect will still be able to
probe the clients by their privacy address when they visit that
server. The duration for which privacy addresses are valid will
impact the usefulness of such observed addresses to an external
attacker. For example, a worm that may spread using such observed
addresses may be less effective if it relies on harvested privacy
addresses. The frequency with which such address get recycled could
be increased, though this may increase the complexity of local
network management for the administrator, since doing so will cause
more addresses to be used over time in the site.
A further option here may be to consider using different addresses
for specific applications, or even each new application instance,
which may reduce exposure to other services running on the same host
when such an address is observed externally.
5.2. Cryptographically Generated Addresses (CGAs)
The use of Cryptographically Generated Addresses (CGAs) [9] may also
cause the search space to be increased from that presented by default
use of stateless autoconfiguration. Such addresses would be seen
where Secure Neighbour Discovery (SEND) [8] is in use.
Chown Informational [Page 9]
RFC 5157 IPv6 Network Scanning March 2008
5.3. Non-Use of MAC Addresses in EUI-64 Format
The EUI-64 identifier format does not require the use of MAC
addresses for identifier construction. At least one well known
operating system currently defaults to generation of the 64-bit
interface identifier by use of random bits, and thus does not embed
the MAC address. Where such a method exists, an administrator may
wish to consider using that option.
5.4. DHCP Service Configuration Options
One option open to an administrator is to configure DHCPv6, if
possible, so that the first addresses allocated from the pool begins
much higher in the address space than at [prefix]::1. Further, it is
desirable that allocated addresses are not sequential and do not have
any predictable pattern to them. Unpredictable sparseness in the
allocated addresses is a desirable property. DHCPv6 implementers
could reduce the cost for administrators to deploy such 'random'
addressing by supporting configuration options to allow such
behaviour.
DHCPv6 also includes an option to use privacy extension [3]
addresses, i.e., temporary addresses, as described in Section 12 of
the DHCPv6 [6] specification.
6. Conclusions
Due to the much larger size of IPv6 subnets in comparison to IPv4, it
will become less feasible for traditional network scanning methods to
detect open services for subsequent attacks, assuming the attackers
are off-site and services are not listed in the DNS. If
administrators number their IPv6 subnets in 'random', non-predictable
ways, attackers, whether they be in the form of automated network
scanners or dynamic worm propagation, will need to make wider use of
new methods to determine IPv6 host addresses to target (e.g., looking
to obtain logs of activity from a site and scanning addresses around
the ones observed). Such numbering schemes may be very low cost to
deploy in comparison to conventional sequential numbering, and thus,
a useful part of an overall defence-in-depth strategy. Of course, if
those systems are dual-stack, and have open IPv4 services running,
they will remain exposed to traditional probes over IPv4 transport.
7. Security Considerations
There are no specific security considerations in this document
outside of the topic of discussion itself. However, it must be noted
that the 'security through obscurity' discussions and commentary
within this text must be noted in their proper context. Relying
Chown Informational [Page 10]
RFC 5157 IPv6 Network Scanning March 2008
purely on obscurity of a node address is not prudent, rather the
advice here should be considered as part of a 'defence-in-depth'
approach to security for a site or network. This also implies that
these measures require coordination between network administrators
and those who maintain DNS services, though this is common in most
scenarios.
8. Acknowledgements
Thanks are due to people in the 6NET project (www.6net.org) for
discussion of this topic, including Pekka Savola, Christian Strauf,
and Martin Dunmore, as well as other contributors from the IETF v6ops
and other mailing lists, including Tony Finch, David Malone, Bernie
Volz, Fred Baker, Andrew Sullivan, Tony Hain, Dave Thaler, and Alex
Petrescu. Thanks are also due for editorial feedback from Brian
Carpenter, Lars Eggert, and Jonne Soininen amongst others.
9. Informative References
[1] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6)
Specification", RFC 2460, December 1998.
[2] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless Address
Autoconfiguration", RFC 4862, September 2007.
[3] Narten, T., Draves, R., and S. Krishnan, "Privacy Extensions
for Stateless Address Autoconfiguration in IPv6", RFC 4941,
September 2007.
[4] Carpenter, B. and K. Moore, "Connection of IPv6 Domains via
IPv4 Clouds", RFC 3056, February 2001.
[5] Haberman, B. and D. Thaler, "Unicast-Prefix-based IPv6
Multicast Addresses", RFC 3306, August 2002.
[6] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C., and M.
Carney, "Dynamic Host Configuration Protocol for IPv6
(DHCPv6)", RFC 3315, July 2003.
[7] Savola, P. and B. Haberman, "Embedding the Rendezvous Point
(RP) Address in an IPv6 Multicast Address", RFC 3956,
November 2004.
[8] Arkko, J., Kempf, J., Zill, B., and P. Nikander, "SEcure
Neighbor Discovery (SEND)", RFC 3971, March 2005.
[9] Aura, T., "Cryptographically Generated Addresses (CGA)",
RFC 3972, March 2005.
Chown Informational [Page 11]
RFC 5157 IPv6 Network Scanning March 2008
[10] Templin, F., Gleeson, T., Talwar, M., and D. Thaler, "Intra-
Site Automatic Tunnel Addressing Protocol (ISATAP)", RFC 4214,
October 2005.
[11] Huitema, C., "Teredo: Tunneling IPv6 over UDP through Network
Address Translations (NATs)", RFC 4380, February 2006.
[12] Davies, E., Krishnan, S., and P. Savola, "IPv6 Transition/
Co-existence Security Considerations", RFC 4942,
September 2007.
[13] Bellovin, S., et al, "Worm Propagation Strategies in an IPv6
Internet", as published in ;login:, February 2006,
<http://www.cs.columbia.edu/~smb/papers/v6worms.pdf>.
Author's Address
Tim Chown
University of Southampton
Southampton, Hampshire SO17 1BJ
United Kingdom
EMail: tjc@ecs.soton.ac.uk
Chown Informational [Page 12]
RFC 5157 IPv6 Network Scanning March 2008
Full Copyright Statement
Copyright (C) The IETF Trust (2008).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Chown Informational [Page 13]