💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc1494.txt captured on 2023-12-28 at 18:50:27.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group H. Alvestrand
Request for Comments: 1494 SINTEF DELAB
S. Thompson
Soft*Switch, Inc.
August 1993
Equivalences between 1988 X.400 and RFC-822 Message Bodies
Status of this Memo
This RFC specifies an IAB standards track protocol for the Internet
community, and requests discussion and suggestions for improvements.
Please refer to the current edition of the "IAB Official Protocol
Standards" for the standardization state and status of this protocol.
Distribution of this memo is unlimited.
Table of Contents
1. Introduction ............................................. 2
2. Equivalence Table Definition ............................. 2
3. Generic conversions ...................................... 3
3.1. Byte copy .............................................. 3
3.2. Text Conversion ........................................ 3
3.3. Image Conversion ....................................... 3
3.4. Tunneling .............................................. 3
4. Conversion Table for known X.400 and MIME Types ......... 4
4.1. MIME to X.400 Table .................................... 4
4.2. X.400 to MIME Table .................................... 4
5. Newly defined X.400 Body Parts ........................... 5
5.1. Use of OBJECT IDENTIFIERs and ASN.1 MACROS ............. 5
5.2. The Generic MIME Extended Body Part .................... 6
5.3. The PostScript body part ............................... 7
5.4. The JPEG body part ..................................... 7
5.5. The GIF body part ...................................... 8
6. Newly defined MIME content-types ......................... 8
6.1. The application/x400-bp content-type ................... 8
6.2. The image/g3fax content-type ........................... 9
6.2.1. G3Fax Parameters ..................................... 9
6.2.2. Content Encoding ..................................... 10
6.3. The Application/ODA content-type ....................... 11
7. Equivalence Definitions ................................... 11
7.1. IA5Text - text/plain .................................... 11
7.2. GeneralText - text/plain (ISO-8859) ..................... 12
7.3. BilaterallyDefined - application/octet-stream .......... 13
7.4. ODA - application/oda ................................... 14
7.5. g3-facsimile - image/g3fax .............................. 15
7.6. application/postscript - postscript-body-part .......... 16
7.7. application/jpeg - jpeg-body-part ....................... 16
Alvestrand & Thompson [Page 1]
RFC 1494 X.400/MIME Body Equivalences August 1993
7.8. image/gif - gif-body-part ............................... 16
8. OID Assignments ........................................... 17
9. IANA Registration form for new mappings ................... 17
10. Security Considerations .................................. 18
11. Authors' Addresses ....................................... 18
12. References ............................................... 19
1. Introduction
This document is a companion to [1], which defines the principles
behind interworking between MIME-based RFC-822 mail and X.400 mail.
This document describes the content of the "IANA MHS/MIME Equivalence
table" referenced in the companion document, and defines the initial
configuration of this table. Mappings for new MIME content-types
and/or X.400 body part types should be registered with the IANA to
minimize redundancy and promote interoperability.
In MIME, the term "content-type" is used to refer to an information
object contained in the body of a message. In contrast, X.400 uses
the term "body part type." In this document, the term "body part" is
used to refer to either.
Please send comments to the MIME-MHS mailing list:
<mime-mhs@surfnet.nl>.
2. Equivalence Table Definition
For each MIME content-type/X.400 body part pair, the Equivalence
Table will contain an entry with the following sections:
X.400 Body Part
This section identifies the X.400 Body Part governed by this
Table entry. It includes any OBJECT IDENTIFIERs or other
parameters necessary to uniquely identify the Body Part.
MIME Content-Type
This section identifies the MIME content-type governed by this
Table entry. The MIME content-type named here must be
registered with the IANA.
Conversion Type
This section identifies the type of conversion applied. See the
section on Generic Conversions for an explanation of the
possible values.
Alvestrand & Thompson [Page 2]
RFC 1494 X.400/MIME Body Equivalences August 1993
Comments (optional)
This section gives any additional commentary that might be
useful in understanding the mapping between the X.400 and MIME
representations.
The initial Equivalence Table entries in this document are described
using this convention. Any future submissions to the IANA should
follow this format.
3. Generic conversions
3.1. Byte copy
This is the trivial case, that is, no conversion at all. The byte
stream is simply copied between MIME and X.400.
This is the preferred conversion, since it is the simplest.
Implementors and vendors will be registering OBJECT IDENTIFIERs and
MIME content-types for their various objects. They are STRONGLY
ENCOURAGED to specify their content formats such that a gateway can
use Byte Copy to map between them.
Note that in some cases, it is necessary to define exactly which
ASN.1 construct to replace with the content of the MIME object.
3.2. Text Conversion
This type of conversion applies to text objects that cannot be mapped
using a simple Byte Copy. Conversion involves scanning and
reformatting the object. For example, the MIME and X.400 objects
might differ in their encoding of nonstandard characters, or line or
page breaks.
3.3. Image Conversion
This conversion type applies to raster images, like Group 3 Facsimile
or JPEG. Again, it differs from Byte Copy in that it involves
scanning reformatting the byte stream. It differs from Text
Conversion in that it is pixel- oriented, rather than character-
oriented.
3.4. Tunneling
This is not a conversion at all, but an encapsulation of the object.
This is the fallback conversion, used when no explicit mapping
applies.
Alvestrand & Thompson [Page 3]
RFC 1494 X.400/MIME Body Equivalences August 1993
4. Conversion Table for known X.400 and MIME Types
This section itemizes the equivalences for all currently known MIME
content-types and X.400 body parts.
4.1. MIME to X.400 Table
MIME content-type X.400 Body Part Section
----------------- ------------------ -------
text/plain
charset=us-ascii ia5-text 7.1
charset=iso-8859-x EBP - GeneralText 7.2
text/richtext no mapping defined 5.2
application/oda EBP - ODA 7.4
application/octet-stream bilaterally-defined 7.3
application/postscript EBP - mime-postscript-body 5.4, 7.6
image/g3fax g3-facsimile 6.2, 7.5
image/jpeg EBP - mime-jpeg-body 5.5, 7.7
image/gif EBP - mime-gif-body 5.6, 7.8
audio/basic no mapping defined 5.2
video/mpeg no mapping defined 5.2
Abbreviation: EBP - Extended Body Part
4.2. X.400 to MIME Table
Basic Body Parts
X.400 Basic Body Part MIME content-type Section
--------------------- -------------------- -------
ia5-text text/plain;charset=us-ascii 7.1
voice No Mapping Defined 6.1
g3-facsimile image/g3fax 6.2, 7.5
g4-class1 no mapping defined 6.1
teletex no mapping defined 6.1
videotex no mapping defined 6.1
encrypted no mapping defined 6.1
bilaterally-defined application/octet-stream 7.3
nationally-defined no mapping defined 6.1
externally-defined See Extended Body Parts 6.1
X.400 Extended Body Part MIME content-type Section
------------------------- -------------------- -------
GeneralText text/plain;charset=iso-8859-x 7.2
ODA application/oda 7.4
mime-postscript-body application/postscript 5.3, 7.6
mime-jpeg-body image/jpeg 5.4, 7.7
mime-gif-body image/gif 5.5, 7.8
Alvestrand & Thompson [Page 4]
RFC 1494 X.400/MIME Body Equivalences August 1993
5. Newly defined X.400 Body Parts
This section defines new X.400 Body Parts for the purposes of
interworking with MIME.
All new X.400 Body Parts defined here will be Extended Body Parts, as
defined in CCITT Recommendation X.420 [2].
5.1. Use of OBJECT IDENTIFIERs and ASN.1 MACROS
X.420 dictates that Extended Body Parts shall:
(1) use OBJECT IDENTIFIERs (OIDs) to uniquely identify
the contents, and
(2) be defined by using the ASN.1 Macro:
EXTENDED-BODY-PART-TYPE MACRO::=
BEGIN
TYPE NOTATION ::= Parameters Data
VALUE NOTATION ::= value (VALUE OBJECT IDENTIFIER)
Parameters ::= "PARAMETERS" type "IDENTIFIED"
"BY" value(OBJECT IDENTIFIER)
| empty;
Data ::= "DATA" type
END
To meet these requirements, this document uses the OID
mime-mhs-bodies
defined in [1], as the root OID for X.400 Extended Body Parts defined
for MIME interworking.
Each Extended Body Part contains Data and optional Parameters, each
being named by an OID. To this end, two OID subtrees are defined
under mime-mhs-bodies, one for Data, and the other for Parameters:
mime-mhs-bp-data OBJECT IDENTIFIER ::=
{ mime-mhs-bodies 1 }
mime-mhs-bp-parameter OBJECT IDENTIFIER ::=
{ mime-mhs-bodies 2 }
All definitions of X.400 body parts submitted to the IANA for
registration must use the Extended Body Part Type macro for the
definition. See the next section for an example.
Alvestrand & Thompson [Page 5]
RFC 1494 X.400/MIME Body Equivalences August 1993
Lastly, the IANA will use the mime-mhs-bp-data and mime-mhs-bp-
parameter OIDs as root OIDs for any new MIME content-type/subtypes
that aren't otherwise registered in the Equivalence Table.
5.2. The Generic MIME Extended Body Part
The following X.400 Body Part is defined to carry any MIME content-
type for which there is no explicit IANA registered mapping.
mime-body-part EXTENDED-BODY-PART-TYPE
PARAMETERS MimeParameters
IDENTIFIED BY mime-generic-parameters
DATA OCTET STRING
::= mime-generic-data
MimeParameters ::=
SEQUENCE {
content-type IA5String,
content-parameters SEQUENCE OF
SEQUENCE {
parameter IA5String,
parameter-value IA5String
}
-- from RFC-1327, sec. 5.1.12
other-header-fields RFC822FieldList
}
mime-generic-parameters OBJECT IDENTIFIER ::=
{ mime-mhs-bp-parameter 1 }
mime-generic-data OBJECT IDENTIFIER ::=
{ mime-mhs-bp-data 1 }
To convert the MIME content-type into the X.400 mime- body-part:
(1) Copy the "type/subtype" string from the MIME
Content-Type: header field into
MimeParameters.content-type
(2) For each "parameter=value" string in the MIME
Content-Type header field, create a
MimeParameters.content-parameters structure, and copy
the "parameter" string into MimeParameters.content-
parameters.parameter field and the "value" string
into the paired MimeParameters.content-
parameters.parameter-value field.
(3) Convert the MIME body part into its canonical form.
Alvestrand & Thompson [Page 6]
RFC 1494 X.400/MIME Body Equivalences August 1993
(See appendix H of RFC 1341 [3] for a discussion
of canonical in this context.) Said another way,
reverse the transfer encoding to recover the original
byte stream.
(4) Copy the canonical byte stream into the mime-body-
part.data octet string.
(5) Remove the Content-type and the Content-transfer-
encoding header fields from the MIME body part's
RFC822 header.
(6) Any header fields starting with "Content-" in the
MIME body part is placed in the optional other-
header-fields structure. Note that this can only
occur when the MIME content-type occurs as part of a
"multipart" content-type.
The mapping from the X.400 mime-body-part to a MIME content-type is
the inverse of the above steps.
5.3. The PostScript body part
The following Extended Body Part is defined for PostScript data
streams. It has no parameters.
postscript-body-part EXTENDED-BODY-PART-TYPE
DATA OCTET STRING
::= mime-postscript-body
mime-postscript-body OBJECT IDENTIFIER ::=
{ mime-mhs-bp-data 2 }
5.4. The JPEG body part
The following Extended Body Part is defined for JPEG data streams.
It has no parameters.
jpeg-body-part EXTENDED-BODY-PART-TYPE
DATA OCTET STRING
::= mime-jpeg-body
mime-jpeg-body OBJECT IDENTIFIER ::=
{ mime-mhs-bp-data 3 }
Alvestrand & Thompson [Page 7]
RFC 1494 X.400/MIME Body Equivalences August 1993
5.5. The GIF body part
The following Extended Body Part is defined for GIF data streams. It
has no parameters.
gif-body-part EXTENDED-BODY-PART-TYPE
DATA OCTET STRING
::= mime-gif-body
mime-gif-body OBJECT IDENTIFIER ::=
{ mime-mhs-bp-data 4 }
6. Newly defined MIME content-types
This section defines new MIME content-types for the purposes of
interworking with X.400.
6.1. The application/x400-bp content-type
This content-type is defined to carry any X.400(88) body part for
which there is no registered IANA mapping.
The content-type field is
application/x400-bp
The parameters are:
bp-type=<INTEGER or OBJECT IDENTIFIER>
The body contains the raw ASN.1 IPM.body octet stream, including the
initial tag octet.
If the body is a basic body part, the bp-type parameter is set to the
number of the body part's context-specific tag, that is, the tag of
the IPMS.Body.BodyPart component.
If the body is an Extended Body Part, the bp-type parameter is set to
the OBJECT IDENTIFIER from
IPMS.body.externally-defined.data.direct-reference
No attempt is made to turn the parameters of Extended Body Parts into
MIME parameters. (This task is the responsibility of the recipient's
UA).
For example, a basic VideotexBodyPart will have
Alvestrand & Thompson [Page 8]
RFC 1494 X.400/MIME Body Equivalences August 1993
Content-type=application/x400-bp; bp-type=6
whilst a Extended Videotex body part will have
Content-type=application/x400-bp; bp-type=2.6.1.4.5
application/x400-bp will need a content-transfer-encoding of base64
or quoted-printable when carried in 7-bit MIME. Since there is no
way to know beforehand the content, it is recommended to just inspect
the first 1 KByte or so of data and choose the one that seems to
produce the more compact encoding.
If this is not feasible, Base64 is recommended.
6.2. The image/g3fax content-type
This content-type is defined to carry G3 Facsimile byte streams.
In general, a G3Fax image contains 3 pieces of information:
(1) A set of flags indicating the particular coding
scheme. CCITT Recommendation T.30 defines how the
flags are transmitted over telephones. In this
medium, the flags are carried as parameters in the
MIME content-type header field.
(2) A structure that divides the bits into pages. CCITT
recommendation T.30 describes how to define page
boundaries. A page break algorithm is defined here
that is independent of how the image data is
conveyed.
(3) For each page, a sequence of bits that form the
encoding of the image. CCITT recommendation T.4
defines the bit image format. This is used without
change.
6.2.1. G3Fax Parameters
The following parameters are defined:
(1) page-length - possible values: A4, B4 and Unlimited
(2) page-width - possible values: A3, A4, B4
(3) encoding - possible values: 1-dimensional, 2-
dimensional, Uncompressed
Alvestrand & Thompson [Page 9]
RFC 1494 X.400/MIME Body Equivalences August 1993
(4) resolution - possible values: Fine, Coarse
(5) DCS - a bit string, represented in Base64.
(6) pages - an integer, giving the number of pages in the
document
If nothing is specified, the default parameter settings are:
page-length=A4
page-width=A4
encoding=1-dimensional
resolution=Coarse
It is possible (but misleading) to view the representation of these
values as single-bit flags. They correspond to the following bits of
the T.30 control string and X.400 G3FacsimileParameters:
Parameter T.30 bit X.400 bit
page-length=A4 no bit set
page-length=B4 19 21
page-length=Unlimited 20 20
page-width=A4 no bit set
page-width=A3 18 22
page-width=B4 17 23
encoding=1-dimensional no bit set
encoding=2-dimensional 16 8
encoding=Uncompressed 26 30
resolution=Coarse no bit set
resolution=Fine 15 9
The reason for the different bit numbers is that X.400 counts bits in
an octet from the MSB down to the LSB, while T.30 uses the opposite
numbering scheme.
If any bit but these are set in the Device Control String, the DCS
parameter should be supplied.
6.2.2. Content Encoding
X.400 defines the g3-facsimile data stream as a SEQUENCE of BIT
STRINGs. Each BIT STRING is a page of facsimile image data, encoded
as defined by Recommendation T.4. The following content encoding is
reversible between MIME and X.400 and ensures that page breaks are
Alvestrand & Thompson [Page 10]
RFC 1494 X.400/MIME Body Equivalences August 1993
honored in the MIME representation.
An EOL is defined as a bit sequence of
000000000001 (eleven zeroes and a one).
Each page of the message is delimited by a sequence of six (6) EOLs
that MUST start on a byte boundary. The image bit stream is padded
as needed to achieve this alignment.
Searching for the boundary is a matter of searching for the byte
sequence (HEX) 00 10 01 00 10 01 00 10 01, which cannot occur inside
the image.
See Section 7.5 for the algorithm on conversion between this encoding
and the X.400 encoding.
The Base64 content-transfer-encoding is appropriate for carrying this
content-type.
6.3. The Application/ODA content-type
The "ODA" subtype of application is used to indicate that a body
contains information encoded according to the Office Document
Architecture [4] standards, using the ODIF representation format.
For application/oda, the Content- Type line should also specify an
attribute/value pair that indicates the document application profile
(DAP), using the key word "profile", and the document class, using
the keyword "class".
For the keyword "class", the values "formatted", "processable" and
"formatted-processable" are legal values.
Thus an appropriate header field might look like this:
Content-Type: application/oda; profile=Q112;
class=formatted
Consult the ODA standard [4] for further information.
The Base64 content-transfer-encoding is appropriate for carrying ODA.
7. Equivalence Definitions
7.1. IA5Text - text/plain
X.400 Body Part: IA5Text
MIME Content-type: text/plain; charset=US-ASCII
Alvestrand & Thompson [Page 11]
RFC 1494 X.400/MIME Body Equivalences August 1993
Conversion Type: Byte copy
Comments:
When mapping from X.400 to MIME, the "repertoire" parameter is
ignored.
When mapping from MIME to X.400, the "repertoire" parameter is set to
IA5 (5).
NOTE: The MIME Content-type headers are omitted, when mapping from
X.400 to MIME, if and only if the IA5Text body part is the only body
part in the IPMS.Body sequence.
NOTE: IA5Text specifies the "currency" symbol in position 2/4. This
is converted without comment to the "dollar" symbol, since the author
of this document has seen many documents in which the position was
intended to indicate "dollar" while he has not yet seen one in which
the "currency" symbol is intended.
(For reference: The T.50 (1988) recommendation, which defines IA5,
talks about ISO registered set number 2, while ASCII, using the
"dollar" symbol, is ISO registered set number 6. There are no other
differences.)
7.2. GeneralText - text/plain (ISO-8859)
X.400 Body Part: GeneralText; CharacterSets in
6,100,101,109,110,126,127,138,144,148
MIME Content-Type: text/plain; charset=ISO-8859-(1-9)
Conversion Type: Byte copy
Comments:
When mapping from X.400 to MIME, the character-set chosen from table
below according to the value of Parameters.CharacterSets.
When mapping from MIME to X.400, GeneralText is an Extended Body
Part, hence it requires an OID. The OID for the GeneralText body is
defined in [5], part 8, annex D, as {2 6 1 4 11}. The OID for the
parameters is {2 6 1 11 11}.
The Parameters.CharacterSets is set from table below according to the
value of "charset"
NOTE: The GeneralText body part is defined in ISO 10021-8 [5], and
NOT in the corresponding CCITT recommendation. Its parameters were
heavily modified in a defect report, and will be a SET OF INTEGER
(indicating the ISO registry numbers of all the used sets) in the
next version of the standard.
Alvestrand & Thompson [Page 12]
RFC 1494 X.400/MIME Body Equivalences August 1993
The following table lists the MIME character sets and the
corresponding ISO registry numbers. If no correspondence is found,
this conversion fails, and the generic body part approach is used.
MIME charset ISO IR numbers Comment
-----------------------------------------------
ISO-8859-1 6, 100 West European "8-bit ASCII"
ISO-8859-2 6, 101 East European
ISO-8859-3 6, 109 <regarded as obsolete>
ISO-8859-4 6, 110 <regarded as obsolete>
ISO-8859-5 6, 144 Cyrillic
ISO-8859-6 6, 127 Arabic
ISO-8859-7 6, 126 Greek
ISO-8859-8 6, 138 Hebrew
ISO-8859-8 6, 148 Other Latin-using languages
When converting from MIME to X.400, generate the correct OIDs for use
in the message envelope's Encoded Information Types by looking up the
ISO IR number in the above table, and then appending it to the id-
cs-eit-authority {1 0 10021 7 1 0} OID.
The escape sequences to designate and invoke the relevant character
sets in their proper positions must be added to the front of the
GeneralText character string.
7.3. BilaterallyDefined - application/octet-stream
X.400 Body Part: BilaterallyDefined
MIME Content-Type: Application/Octet-Stream (no parameters)
Conversion Type: Byte copy
Comments:
When mapping from MIME to X.400, if there are parameters present in
the Content-Type: header field, the conversion fails since the
BilaterallyDefined Body Part does not have any corresponding ASN.1
parameters.
DISCUSSION: The parameters "name" "type" and "conversions" are
advisory, but may in some cases give vital hints on the expected
handling of the file. The parameter "conversions" is not fully
defined, but it is expected that it will be useful, so we cannot drop
it and expect people to be satisfied.
The parameter "padding" changes the interpretation of the last byte
of the data, and so cannot be deleted.
An option is to prepend an IA5 body part that contains the parameter
text; this will aid unmodified readers, and can probably be made
Alvestrand & Thompson [Page 13]
RFC 1494 X.400/MIME Body Equivalences August 1993
reversible with suitable chicanery, but is it worth it????
Also, use of BilaterallyDefined Body Parts is specifically deprecated
in both 1988 and 1992 X.400. It is retained solely for backward
compatibility with 1984 systems. 1992 X.400 defines a File Transfer
Body Part to solve this problem (i.e. binary file transfer through
email). The standard and its regional profiles are not solid enough
yet to exploit as a solution for this problem.
7.4. ODA - application/oda
X.400 Body Part: ODA
MIME Content-Type: application/oda
Conversion Type: Byte copy
Comments:
The ODA body part is defined in the CCITT document T.411 [6],
appendix E, section E.2, "ODA identification in the P2 protocol of
MHS"
An abbreviated version of its ASN.1 definition is:
oda-body-part EXTENDED-BODY-PART-TYPE
PARAMETERS OdaBodyPartParameters
DATA OdaData
::= id-et-oda
OdaBodyPartParameters ::= SET {
document-application-profile [0] OBJECT IDENTIFIER
document-architecture-class [1] INTEGER {
formatted (0)
processable (1)
formatted-processable(2)}}
id-et-oda OBJECT IDENTIFIER ::= { 2 8 1 0 1 }
Mapping from X.400 to MIME, the following is done:
The Parameters.document-application-profile is mapped onto the MIME
parameter "profile" according to the table below.
Profile OBJECT IDENTIFIER
Q112 { iso (1) identified-organization (3) ewos (16)
eg (2) oda (6) profile (0) q112 (1) }
The Parameters.document-architecture-class is mapped onto the MIME
parameter "class" according to the table below
Alvestrand & Thompson [Page 14]
RFC 1494 X.400/MIME Body Equivalences August 1993
String Integer
formatted formatted(0)
processable processable(1)
formatted-processable formatted-processable(2)
NOTE: This parameter is not defined in RFC 1341.
The body of the MIME content-type is the Data part of the ODA body
part.
When mapping from MIME to X.400, the following steps are done:
The Parameters.document-application-profile and Parameters.document-
architecture-class are set from the tables above. If any of the
parameters are missing, the values for Q112 and formatted-processable
are used.
It is an option for the gateway implementor to try to access them
from inside the document, where they are defined as
document-profile.document-characteristics.document-architecture-class
document-profile.document-characteristics.document-application-profile
Gateways are NOT required to do this, since the document-
characteristics are optional parameters. If a gateway does not, it
simply uses the defaulting rules defined above.
The OBJECT IDENTIFIERs for the document application profile and for
ODA {2 8 0 0} must be added to the Encoded Information Types
parameter of the message envelope.
7.5. g3-facsimile - image/g3fax
X.400 Body part: g3-facsimile
MIME Content-Type: image/g3fax
Conversion Type: nearly Byte copy
Comments:
The Parameters of the X.400 G3Fax body part are mapped to the
corresponding Parameters on the MIME Image/G3Fax body part and vice
versa. Note that:
(1) If fineResolution is not specified, pixels will be
twice as tall as they are wide
(2) If any bit not corresponding to a specially named
Alvestrand & Thompson [Page 15]
RFC 1494 X.400/MIME Body Equivalences August 1993
option is set in the G3Fax NonBasicParameters, the
"DCS" parameter must be used.
(3) Interworking is not guaranteed if any bit apart from
those specially named are used in the
NonBasicParameters
From X.400 to G3Fax, the body is created in the following way:
(1) Any trailing EOL markers on each bitstring is
removed. The bistring is padded to a byte boundary.
(2) 6 consecutive EOL markers are appended to each
bitstring.
(3) The padded bitstrings are concatenated together
An EOL marker is the bit sequence 000000000001 (11 zeroes and a one).
From G3Fax to X.400, the body is created in the following way:
(1) The body is split into bitstrings at each occurrence
of 6 consecutive EOL markers, and trailing EOLs and
padding are removed
(2) Each bitstring is made into an ASN.1 BITSTRING
(3) The bitstrings are made into an ASN.1 SEQUENCE, which
forms the body of the G3Fax body part.
7.6. application/postscript - postscript-body-part
X.400 Body Part: Extended Body Part, OID postscript-body-part
MIME Content-Type: application/postscript
Conversion Type: Byte Copy
7.7. application/jpeg - jpeg-body-part
X.400 Body Part: Extended Body Part, OID jpeg-body-part
MIME Content-Type: application/jpeg
Conversion Type: Byte Copy
7.8. image/gif - gif-body-part
X.400 Body Part: Extended Body Part, OID gif-body-part
MIME Content-Type: application/gif
Conversion Type: Byte Copy
Alvestrand & Thompson [Page 16]
RFC 1494 X.400/MIME Body Equivalences August 1993
8. OID Assignments
MIME-MHS-MAPPINGS DEFINITIONS ::= BEGIN
IMPORTS
mail, mime-mhs, mime-mhs-bodies
FROM MIME-MHS;
mime-mhs-bp-data OBJECT IDENTIFIER ::=
{ mime-mhs-bodies 1}
mime-mhs-bp-parameter OBJECT IDENTIFIER ::=
{ mime-mhs-bodies 2}
mime-generic-data OBJECT IDENTIFIER ::=
{ mime-mhs-bp-data 1}
mime-generic-parameters OBJECT IDENTIFIER ::=
{ mime-mhs-bp-parameter 1}
mime-postscript-body OBJECT IDENTIFIER ::=
{ mime-mhs-bp-data 2}
mime-jpeg-body OBJECT IDENTIFIER ::=
{ mime-mhs-bp-data 3}
mime-gif-body OBJECT IDENTIFIER ::=
{ mime-mhs-bp-data 4};
9. IANA Registration form for new mappings
To: IANA@isi.edu
Subject: Registration of new X.400/MIME content type mapping
MIME type name:
(this must have been registered previously with IANA)
X.400 body part:
X.400 Object Identifier for Data:
(If left empty, an OID will be assigned by IANA under
mime-mhs-bp-data)
X.400 Object Identifier for Parameters:
Alvestrand & Thompson [Page 17]
RFC 1494 X.400/MIME Body Equivalences August 1993
(If left empty, an OID will be assigned by IANA under
mime-mhs-bp-parameter. If it is not used, fill in the
words NOT USED.)
X.400 ASN.1 Syntax:
(must be an EXTENDED-BODY-PART-TYPE macro, or reference to
a Basic body part type)
Conversion algorithm:
(must be defined completely enough for independent
implementation. It may be defined by reference to RFCs).
Person & email address to contact for further information:
INFORMATION TO THE SUBMITTER:
The accepted registrations will be listed in the "Assigned
Numbers" series of RFCs. The information in the
registration form is freely distributable.
10. Security Considerations
Security issues are not discussed in this memo.
11. Authors' Addresses
Harald Tveit Alvestrand
SINTEF DELAB
N-7034 Trondheim
NORWAY
EMail: Harald.Alvestrand@delab.sintef.no
Steven J. Thompson
Soft*Switch, Inc.
640 Lee Road
Wayne, PA 19087
Phone: (215) 640-7556
EMail: sjt@gateway.ssw.com
Alvestrand & Thompson [Page 18]
RFC 1494 X.400/MIME Body Equivalences August 1993
12. References
[1] Alvestrand, H., Kille, S., Miles, R., Rose, M., and S. Thompson,
"Mapping between X.400 and RFC-822 Message Bodies", RFC 1495,
SINTEF DELAB, ISODE Consortium, Soft*Switch, Inc, Dover Beach
Consulting, Inc., Soft*Switch, Inc., August 1993.
[2] CCITT Recommendation X.420 (1988), Interpersonal Messaging
System.
[3] Borenstein, N, and N. Freed, "MIME: Mechanisms for Specifying
and Describing the Format of Internet Message Bodies", RFC 1341,
Bellcore, Innosoft, June 1992.
[4] ISO 8613; Information Processing: Text and Office System; Office
Document Architecture (ODA) and Interchange Format (ODIF), Part
1-8, 1989.
[5] ISO/IEC International Standard 10021, Information technology -
Text Communication - Message-Oriented Text Interchange Systems
(MOTIS) (Parts 1 to 8).
[6] CCITT Recommendation T.411 (1988), Open Document Architecture
(ODA) and Interchange Format, Introduction and General
Principles.
[7] Crocker, D., "Standard for the Format of ARPA Internet Text
Messages", STD 11, RFC 822, UDEL, August 1982.
[8] Hardcastle-Kille, S., "Mapping between X.400(1988) / ISO 10021
and RFC-822", RFC 1327, University College London, May 1992.
[9] CCITT Recommendation T.4, Standardization of Group 3 Facsimile
Apparatus for Document Transmission (1988).
[10] CCITT Recommendation T.30, Procedures For Document Facsimile
Transmission in the General Switched Telephone Network (1988).
[11] CCITT, Data Communication Networks - Message Handling Systems -
Recommendations X.400 - X.420 (1988 version).
[12] Alvestrand, H., "X.400 Use of Extended Character Sets", RFC
1502, SINTEF DELAB, August 1993.
Alvestrand & Thompson [Page 19]