💾 Archived View for spam.works › mirrors › textfiles › programming › asmtutor.txt captured on 2023-11-14 at 11:47:39.
⬅️ Previous capture (2023-06-16)
-=-=-=-=-=-=-
IBM Personal Computer Assembly Language Tutorial Joshua Auerbach Yale University Yale Computer Center 175 Whitney Avenue P. O. Box 2112 New Haven, Connecticut 06520 Installation Code YU Integrated Personal Computers Project Communications Group Communications and Data Base Division Session C316 .pa IBM PC Assembly Language Tutorial 1 This talk is for people who are just getting started with the PC MACRO Assembler. Maybe you are just contemplating doing some coding in assembler, maybe you have tried it with mixed success. If you are here to get aimed in the right direction, to get off to a good start with the assembler, then you have come for the right reason. I can't promise you'll get what you want, but I'll do my best. On the other hand, if you have already turned out some working assembler code, then this talk is likely to be on the elementary side for you. If you want to review a few basics and have no where else pressing to go, then by all means stay. Why Learn Assembler? -------------------- The reasons for LEARNING assembler are not the same as the reasons for USING it in a particular application. But, we have to start with some of the reasons for using it and then I think the reasons for learning it will become clear. First, let's dispose of a bad reason for using it. Don't use it just because you think it is going to execute faster. A particular sequence of ordinary bread-and-butter computations written in PASCAL, C, FORTRAN, or compiled BASIC can do the job just about as fast as the same algorithm coded in assembler. Of course, interpretive BASIC is slower, but if you have a BASIC application which runs too slow you probably want to try com- piling it before you think too much about translating parts of it to another language. On the other hand, high level languages do tend to isolate you from the machine. That is both their strength and their weakness. Usually, when implemented on a micro, a high level language provides an escape mechanism to the underlying operating system or to the bare machine. So, for example, BASIC has its PEEK and POKE. But, the route to the bare machine is often a circuitous one, leading to tricky programming which is hard to follow. For those of us working on PC's connected to SHARE-class mainframes, we are generally concerned with three interfaces: the keyboard, the screen, and the communication line or lines. All three of these entities raise machine dependent issues which are imperfectly addressed by the underlying operat- ing system or by high level languages. Sometimes, the system or the language does too little for you. For example, with the asynch adapter, the system provides no interrupt handler, no buffer, and no flow control. The application is stuck with the respon- sibility for monitoring that port and not missing any characters, then deciding what to do with all errors. BASIC does a reasonable job on some of this, but that is only BASIC. Most other languages do less. IBM PC Assembly Language Tutorial 2 Sometimes, the system may do too much for you. System support for the key- board is an example. At the hardware level, all 83 keys on the keyboard send unique codes when they are pressed, held down, and released. But, someone has decided that certain keys, like Num Lock and Scroll Lock are going to do certain things before the application even sees them and can't therefore be used as ordinary keys. Sometimes, the system does about the right amount of stuff but does it less efficiently then it should. System support for the screen is in this class. If you use only the official interface to the screen you sometimes slow your application down unacceptably. I said before, don't use assem- bler just to speed things up, but there I was talking about mainline code, which generally can't be speeded up much by assembler coding. A critical system interface is a different matter: sometimes we may have to use assembler to bypass a hopelessly inefficient implementation. We don't want to do this if we can avoid it, but sometimes we can't. Assembly language code can overcome these deficiencies. In some cases, you can also overcome these deficiencies by judicious use of the escape valves which your high level language provides. In BASIC, you can PEEK and POKE and INP and OUT your way around a great many issues. In many other lan- guages you can issue system calls and interrupts and usually manage, one way or other, to modify system memory. Writing handlers to take real-time hardware interrupts from the keyboard or asynch port, though, is still going to be a problem in most languages. Some languages claim to let you do it but I have yet to see an acceptably clean implementation done that way. The real reason while assembler is better than "tricky POKEs" for writing machine-dependent code, though, is the same reason why PASCAL is better than assembler for writing a payroll package: it is easier to maintain. Let the high level language do what it does best, but recognize that there are some things which are best done in assembler code. The assembler, unlike the tricky POKE, can make judicious use of equates, macros, labels, and appropriately placed comments to show what is really going on in this machine-dependent realm where it thrives. So, there are times when it becomes appropriate to write in assembler; giv- en that, if you are a responsible programmer or manager, you will want to be "assembler-literate" so you can decide when assembler code should be written. What do I mean by "assembler-literate?" I don't just mean understanding the 8086 architecture; I think, even if you don't write much assembler code yourself, you ought to understand the actual process of turning out assem- bler code and the various ways to incorporate it into an application. You ought to be able to tell good assembler code from bad, and appropriate assembler code from inappropriate. IBM PC Assembly Language Tutorial 3 Steps to becoming ASSEMBLER-LITERATE ------------------------------------ 1. Learn the 8086 architecture and most of the instruction set. Learn what you need to know and ignore what you don't. Reading: The 8086 Primer by Stephen Morse, published by Hayden. You need to read only two chapters, the one on machine organization and the one on the instruction set. 2. Learn about a few simple DOS function calls. Know what services the operating system provides. If appropriate, learn a little about other systems too. It will aid portability later on. Reading: appendices D and E of the PC DOS manual. 3. Learn enough about the MACRO assembler and the LINKer to write some simple things that really work. Here, too, the main thing is figuring out what you don't need to know. Whatever you do, don't study the sam- ple programs distributed with the assembler unless you have nothing better! 4. At the same time as you are learning the assembler itself, you will need to learn a few tools and concepts to properly combine your assem- bler code with the other things you do. If you plan to call assembler subroutines from a high level language, you will need to study the interface notes provided in your language manual. Usually, this forms an appendix of some sort. If you plan to package your assembler rou- tines as .COM programs you will need to learn to do this. You should also learn to use DEBUG. 5. Read the Technical Reference, but very selectively. The most important things to know are the header comments in the BIOS listing. Next, you will want to learn about the RS 232 port and maybe about the video adapters. Notice that the key thing in all five phases is being selective. It is easy to conclude that there is too much to learn unless you can throw away what you don't need. Most of the rest of this talk is going to deal with this very important question of what you need and don't need to learn in each phase. In some cases, I will have to leave you to do almost all of the learning, in others, I will teach a few salient points, enough, I hope, to get you started. I hope you understand that all I can do in an hour is get you started on the way. IBM PC Assembly Language Tutorial 4 Phase 1: Learn the architecture and instruction set ---------------------------------------------------- The Morse book might seem like a lot of book to buy for just two really important chapters; other books devote a lot more space to the instruction set and give you a big beautiful reference page on each instruction. And, some of the other things in the Morse book, although interesting, really aren't very vital and are covered too sketchily to be of any real help. The reason I like the Morse book is that you can just read it; it has a very conversational style, it is very lucid, it tells you what you really need to know, and a little bit more which is by way of background; because nothing really gets belabored to much, you can gracefully forget the things you don't use. And, I very much recommend READING Morse rather than study- ing it. Get the big picture at this point. Now, you want to concentrate on those things which are worth fixing in mem- ory. After you read Morse, you should relate what you have learned to this outline. 1. You want to fix in your mind the idea of the four segment registers CODE, DATA, STACK, and EXTRA. This part is pretty easy to grasp. The 8086 and the 8088 use 20 bit addresses for memory, meaning that they can address up to 1 megabyte of memory. But, the registers and the address fields in all the instructions are no more that 16 bits long. So, how to address all of that memory? Their solution is to put together two 16 bit quantities like this: calculation SSSS0 ---- value in the relevant segment register SHL 4 depicted in AAAA ---- apparent address from register or instruction hexadecimal -------- RRRRR ---- real address placed on address bus In other words, any time memory is accessed, your program will supply a sixteen bit address. Another sixteen bit address is acquired from a segment register, left shifted four bits (one nibble) and added to it to form the real address. You can control the values in the segment registers and thus access any part of memory you want. But the segment registers are specialized: one for code, one for most data accesses, one for the stack (which we'll mention again) and one "extra" one for additional data accesses. Most people, when they first learn about this addressing scheme become obsessed with converting everything to real 20 bit addresses. After a while, though, you get use to thinking in segment/offset form. You tend to get your segment registers set up at the beginning of the pro- gram, change them as little as possible, and think just in terms of symbolic locations in your program, as with any assembly language. IBM PC Assembly Language Tutorial 5 EXAMPLE: MOV AX,DATASEG MOV DS,AX ;Set value of Data segment ASSUME DS:DATASEG ;Tell assembler DS is usable ....... MOV AX,PLACE ;Access storage symbolically by 16 bit address In the above example, the assembler knows that no special issues are involved because the machine generally uses the DS register to complete a normal data reference. If you had used ES instead of DS in the above example, the assembler would have known what to do, also. In front of the MOV instruction which accessed the location PLACE, it would have placed the ES segment prefix. This would tell the machine that ES should be used, instead of DS, to complete the address. Some conventions make it especially easy to forget about segment regis- ters. For example, any program of the COM type gets control with all four segment registers containing the same value. This program exe- cutes in a simplified 64K address space. You can go outside this address space if you want but you don't have to. 2. You will want to learn what other registers are available and learn their personalities: AX and DX are general purpose registers. They become special only when accessing machine and system interfaces. CX is a general purpose register which is slightly specialized for counting. BX is a general purpose register which is slightly specialized for forming base-displacement addresses. AX-DX can be divided in half, forming AH, AL, BH, BL, CH, CL, DH, DL. SI and DI are strictly 16 bit. They can be used to form indexed addresses (like BX) and they are also used to point to strings. SP is hardly ever manipulated. It is there to provide a stack. BP is a manipulable cousin to SP. Use it to access data which has been pushed onto the stack. Most sixteen bit operations are legal (even if unusual) when per- formed in SI, DI, SP, or BP. IBM PC Assembly Language Tutorial 6 3. You will want to learn the classifications of operations available WITHOUT getting hung up in the details of how 8086 opcodes are con- structed. 8086 opcodes are complex. Fortunately, the assembler opcodes used to assemble them are simple. When you read a book like Morse, you will learn some things which are worth knowing but NOT worth dwelling on. a. 8086 and 8088 instructions can be broken up into subfields and bits with names like R/M, MOD, S and W. These parts of the instruction modify the basic operation in such ways as whether it is 8 bit or 16 bit, if 16 bit, whether all 16 bits of the data are given, whether the instruction is register to register, register to memory, or memory to register, for operands which are registers, which register, for operands which are memory, what base and index registers should be used in finding the data. b. Also, some instructions are actually represented by several differ- ent machine opcodes depending on whether they deal with immediate data or not, or on other issues, and there are some expedited forms which assume that one of the arguments is the most commonly used operand, like AX in the case of arithmetic. There is no point in memorizing any of this detail; just distill the bottom line, which is, what kinds of operand combinations EXIST in the instruction set and what kinds don't. If you ask the assembler to ADD two things and the two things are things for which there is a legal ADD instruction somewhere in the instruction set, the assembler will find the right instruction and fill in all the modifier fields for you. I guess if you memorized all the opcode construction rules you might have a crack at being able to disassemble hex dumps by eye, like you may have learned to do somewhat with 370 assembler. I submit to you that this feat, if ever mastered by anyone, would be in the same class as playing the "Minute Waltz" in a minute; a curiosity only. IBM PC Assembly Language Tutorial 7 Here is the basic matrix you should remember: Two operands: One operand: R <-- M R M <-- R M R <-- R S * R|M <-- I R|M <-- S * S <-- R|M * * -- data moving instructions (MOV, PUSH, POP) only S -- segment register (CS, DS, ES, SS) R -- ordinary register (AX, BX, CX, DX, SI, DI, BP, SP, AH, AL, BH, BL, CH, CL, DH, DL) M -- one of the following pure address [BX]+offset [BP]+offset any of the above indexed by SI any of the first three indexed by DI 4. Of course, you want to learn the operations themselves. As I've sug- gested, you want to learn the op codes as the assembler presents them, not as the CPU machine language presents them. So, even though there are many MOV op codes you don't need to learn them. Basically, here is the instruction set: a. Ordinary two operand instructions. These instructions perform an operation and leave the result in place of one of the operands. They are 1) ADD and ADC -- addition, with or without including a carry from a previous addition 2) SUB and SBB -- subtraction, with or without including a borrow from a previous subtraction 3) CMP -- compare. It is useful to think of this as a subtraction with the answer being thrown away and neither operand actually changed 4) AND, OR, XOR -- typical boolean operations 5) TEST -- like an AND, except the answer is thrown away and nei- ther operand is changed. 6) MOV -- move data from source to target 7) LDS, LES, LEA -- some specialized forms of MOV with side effects IBM PC Assembly Language Tutorial 8 b. Ordinary one operand instructions. These can take any of the oper- and forms described above. Usually, the perform the operation and leave the result in the stated place: 1) INC -- increment contents 2) DEC -- decrement contents 3) NEG -- twos complement 4) NOT -- ones complement 5) PUSH -- value goes on stack (operand location itself unchanged) 6) POP -- value taken from stack, replaces current value c. Now you touch on some instructions which do not follow the general operand rules but which require the use of certain registers. The important ones are 1) The multiply and divide instructions 2) The "adjust" instructions which help in performing arithmetic on ASCII or packed decimal data 3) The shift and rotate instructions. These have a restriction on the second operand: it must either be the immediate value 1 or the contents of the CL register. 4) IN and OUT which send or receive data from one of the 1024 hardware ports. 5) CBW and CWD -- convert byte to word or word to doubleword by sign extension d. Flow of control instructions. These deserve study in themselves and we will discuss them a little more. They include 1) CALL, RET -- call and return 2) INT, IRET -- interrupt and return-from-interrupt 3) JMP -- jump or "branch" 4) LOOP, LOOPNZ, LOOPZ -- special (and useful) instructions which implement a counted loop similar to the 370 BCT instruction 5) various conditional jump instructions IBM PC Assembly Language Tutorial 9 e. String instructions. These implement a limited storage-to-storage instruction subset and are quite powerful. All of them have the property that 1) The source of data is described by the combination DS and SI. 2) The destination of data is described by the combination ES and DI. 3) As part of the operation, the SI and/or DI register(s) is(are) incremented or decremented so the operation can be repeated. They include 1) CMPSB/CMPSW -- compare byte or word 2) LODSB/LODSW -- load byte or word into AL or AX 3) STOSB/STOSW -- store byte or word from AL or AX 4) MOVSB/MOVSW -- move byte or word 5) SCASB/SCASW -- compare byte or word with contents of AL or AX 6) REP/REPE/REPNE -- a prefix which can be combined with any of the above instructions to make them execute repeatedly across a string of data whose length is held in CX. f. Flag instructions: CLI, STI, CLD, STD, CLC, STC. These can set or clear the interrupt (enabled) direction (for string operations) or carry flags. The addressing summary and the instruction summary given above masks a lot of annoying little exceptions. For example, you can't POP CS, and although the R <-- M form of LES is legal, the M <-- R form isn't etc. etc. My advice is a. Go for the general rules b. Don't try to memorize the exceptions c. Rely on common sense and the assembler to teach you about exceptions over time. A lot of the exceptions cover things you wouldn't want to do anyway. IBM PC Assembly Language Tutorial 10 5. A few instructions are rich enough and useful enough to warrent careful study. Here are a few final study guidelines: a. It is well worth the time learning to use the string instruction set effectively. Among the most useful are REP MOVSB ;moves a string REP STOSB ;initializes memory REPNE SCASB ;look up occurance of character in string REPE CMPSB ;compare two strings b. Similarly, if you have never written for a stack machine before, you will need to exercise PUSH and POP and get very comfortable with them because they are going to be good friends. If you are used to the 370, with lots of general purpose registers, you may find yourself feeling cramped at first, with many fewer registers and many instructions having register restrictions. But, you have a hidden ally: you need a register and you don't want to throw away what's in it? Just PUSH it, and when you are done, POP it back. This can lead to abuse. Never have more than two "expedient" PUSHes in effect and never leave something PUSHed across a major header comment or for more than 15 instructions or so. An exception is the saving and restoring of registers at entrance to and exit from a subroutine; here, if the subroutine is long, you should probably PUSH everything which the caller may need saved, whether you will use the register or not, and POP it in reverse order at the end. Be aware that CALL and INT push return address information on the stack and RET and IRET pop it off. It is a good idea to become familiar with the structure of the stack. c. In practice, to invoke system services you will use the INT instruction. It is quite possible to use this instruction effec- tively in a cookbook fashion without knowing precisely how it works. d. The transfer of control instructions (CALL, RET, JMP) deserve care- ful study to avoid confusion. You will learn that these can be classified as follows: 1) all three have the capability of being either NEAR (CS register unchanged) or FAR (CS register changed) 2) JMPs and CALLs can be DIRECT (target is assembled into instruc- tion) or INDIRECT (target fetched from memory or register) 3) if NEAR and DIRECT, a JMP can be SHORT (less than 128 bytes away) or LONG IBM PC Assembly Language Tutorial 11 In general, the third issue is not worth worrying about. On a for- ward jump which is clearly VERY short, you can tell the assembler it is short and save one byte of code: JMP SHORT CLOSEBY On a backward jump, the assembler can figure it out for you. On a forward jump of dubious length, let the assembler default to a LONG form; at worst you waste one byte. Also leave the assembler to worry about how the target address is to be represented, in absolute form or relative form. e. The conditional jump set is rather confusing when studied apart from the assembler, but you do need to get a feeling for it. The interactions of the sign, carry, and overflow flags can get your mind stuttering pretty fast if you worry about it too much. What is boils down to, though, is JZ means what it says JNZ means what it says JG reater this means "if the SIGNED difference is positive" JA bove this means "if the UNSIGNED difference is positive" JL ess this means "if the SIGNED difference is negative" JB elow this means "if the UNSIGNED difference is negative" JC arry assembles the same as JB; it's an aesthetic choice You should understand that all conditional jumps are inherently DIRECT, NEAR, and "short"; the "short" part means that they can't go more than 128 bytes in either direction. Again, this is some- thing you could easily imagine to be more of a problem than it is. I follow this simple approach: 1) When taking an abnormal exit from a block of code, I always use an unconditional jump. Who knows how far you are going to end up jumping by the time the program is finished. For example, I wouldn't code this: TEST AL,IDIBIT ;Is the idiot bit on? JNZ OYVEY ;Yes. Go to general cleanup Rather, I would probably code this: TEST AL,IDIBIT ;Is the idiot bit on? JZ NOIDIOCY ;No. I am saved. JMP OYVEY ;Yes. What can we say... NOIDIOCY: IBM PC Assembly Language Tutorial 12 The latter, of course, is a jump around a jump. Some would say it is evil, but I submit it is hard to avoid in this language. 2) Otherwise, within a block of code, I use conditional jumps freely. If the block eventually grows so long that the assem- bler starts complaining that my conditional jumps are too long I a) consider reorganizing the block but b) also consider changing some conditional jumps to their opposite and use the "jump around a jump" approach as shown above. Enough about specific instructions! 6. Finally, in order to use the assembler effectively, you need to know the default rules for which segment registers are used to complete addresses in which situations. a. CS is used to complete an address which is the target of a NEAR DIRECT jump. On an NEAR INDIRECT jump, DS is used to fetch the address from memory but then CS is used to complete the address thus fetched. On FAR jumps, of course, CS is itself altered. The instruction counter is always implicitly pointing in the code seg- ment. b. SS is used to complete an address if BP is used in its formation. Otherwise, DS is always used to complete a data address. c. On the string instructions, the target is always formed from ES and DI. The source is normally formed from DS and SI. If there is a segment prefix, it overrides the source not the target. Learning about DOS ------------------ I think the best way to learn about DOS internals is to read the technical appendices in the manual. These are not as complete as we might wish, but they really aren't bad; I certainly have learned a lot from them. What you don't learn from them you might eventually learn via judicious disassembly of parts of DOS, but that shouldn't really be necessary. From reading the technical appendices, you learn that interrupts 20H through 27H are used to communicate with DOS. Mostly, you will use inter- rupt 21H, the DOS function manager. The function manager implements a great many services. You request the individual services by means of a function code in the AH register. For example, by putting a nine in the AH register and issuing interrupt 21H you tell DOS to print a message on the console screen. IBM PC Assembly Language Tutorial 13 Usually, but by no means always, the DX register is used to pass data for the service being requested. For example, on the print message service just mentioned, you would put the 16 bit address of the message in the DX register. The DS register is also implicitly part of this argument, in keeping with the universal segmentation rules. In understanding DOS functions, it is useful to understand some history and also some of the philosophy of MS-DOS with regard to portability. General- ly, you will find, once you read the technical information on DOS and also the IBM technical reference, you will know more than one way to do almost anything. Which is best? For example, to do asynch adapter I/O, you can use the DOS calls (pretty incomplete), you can use BIOS, or you can go directly to the hardware. The same thing is true for most of the other primitive I/O (keyboard or screen) although DOS is more likely to give you added value in these areas. When it comes to file I/O, DOS itself offers more than one interface. For example, there are four calls which read data from a file. The way to decide rationally among these alternatives is by understanding the tradeoffs of functionality versus portability. Three kinds of porta- bility need to be considered: machine portability, operating system porta- bility (for example, the ability to assemble and run code under CP/M 86) and DOS version portability (the ability for a program to run under older versions of DOS>. Most of the functions originally offered in DOS 1.0 were direct descendents of CP/M functions; there is even a compatibility interface so that programs which have been translated instruction for instruction from 8080 assembler to 8086 assembler might have a reasonable chance of running if they use only the core CP/M function set. Among the most generally useful in this original compatibility set are 09 -- print a full message on the screen 0A -- get a console input line with full DOS editing 0F -- open a file 10 -- close a file (really needed only when writing) 11 -- find first file matching a pattern 12 -- find next file matching a pattern 13 -- erase a file 16 -- create a file 17 -- rename a file 1A -- set disk transfer address IBM PC Assembly Language Tutorial 14 The next set provide no function above what you can get with BIOS calls or more specialized DOS calls. However, they are preferable to BIOS calls when portability is an issue. 00 -- terminate execution 01 -- read keyboard character 02 -- write screen character 03 -- read COM port character 04 -- write COM port character 05 -- print a character 06 -- read keyboard or write screen with no editing The standard file I/O calls are inferior to the specialized DOS calls but have the advantage of making the program easier to port to CP/M style sys- tems. Thus they are worth mentioning: 14 -- sequential read from file 15 -- sequential write to file 21 -- random read from file 22 -- random write to file 23 -- determine file size 24 -- set random record In addition to the CP/M compatible services, DOS also offers some special- ized services which have been available in all releases of DOS. These include 27 -- multi-record random read. 28 -- multi-record random write. 29 -- parse filename 2A-2D -- get and set date and time All of the calls mentioned above which have anything to do with files make use of a data area called the "FILE CONTROL BLOCK" (FCB). The FCB is any- where from 33 to 37 bytes long depending on how it is used. You are responsible for creating an FCB and filling in the first 12 bytes, which contain a drive code, a file name, and an extension. When you open the FCB, the system fills in the next 20 bytes, which includes a logical record length. The initial lrecl is always 128 bytes, to achieve CP/M compatibility. The system also provides other useful information such as the file size. After you have opened the FCB, you can change the logical record length. If you do this, your program is no longer CP/M compatible, but that doesn't make it a bad thing to do. DOS documentation suggests you use a logical record length of one for maximum flexibility. This is usually a good recommendation. To perform actual I/O to a file, you eventually need to fill in byte 33 or possibly bytes 34-37 of the FCB. Here you supply information about the record you are interested in reading or writing. For the most part, this part of the interface is compatible with CP/M. IBM PC Assembly Language Tutorial 15 In general, you do not need to (and should not) modify other parts of the FCB. The FCB is pretty well described in appendix E of the DOS manual. Beginning with DOS 2.0, there is a whole new system of calls for managing files which don't require that you build an FCB at all. These calls are quite incompatible with CP/M and also mean that your program cannot run under older releases of DOS. However, these calls are very nice and easy to use. They have these characteristics 1. To open, create, delete, or rename a file, you need only a character string representing its name. 2. The open and create calls return a 16 bit value which is simply placed in the BX register on subsequent calls to refer to the file. 3. There is not a separate call required to specify the data buffer. 4. Any number of bytes can be transfered on a single call; no data area must be manipulated to do this. The "new" DOS calls also include comprehensive functions to manipulate the new chained directory structure and to allocate and free memory. Learning the assembler ---------------------- It is my feeling that many people can teach themselves to use the assembler by reading the MACRO Assembler manual if 1. You have read and understood a book like Morse and thus have a feeling for the instruction set 2. You know something about DOS services and so can communicate with the keyboard and screen and do something marginally useful with files. In the absence of this kind of knowledge, you can't write meaningful prac- tice programs and so will not progress. 3. You have access to some good examples (the ones supplied with the assembler are not good, in my opinion. I will try to supply you with some more relevant ones. 4. You ignore the things which are most confusing and least useful. Some of the most confusing aspects of the assembler include the facilities combining segments. But, you can avoid using all but the simplest of these facilities in many cases, even while writing quite substantial applications. 5. The easiest kind of assembler program to write is a COM program. They might seem harder, at first, then EXE programs because there is an extra step involved in creating the executable file, but COM programs are structurally very much simpler. IBM PC Assembly Language Tutorial 16 At this point, it is necessary to talk about COM programs and EXE programs. As you probably know, DOS supports two kinds of executable files. EXE pro- grams are much more general, can contain many segments, and are generally built by compilers and sometimes by the assembler. If you follow the lead given by the samples distributed with the assembler, you will end up with EXE programs. A COM program, in contrast, always contains just one segment, and receives control with all four segment registers containing the same value. A COM program, thus, executes in a simplified environment, a 64K address space. You can go outside this address space simply by tem- porarily changing one segment register, but you don't have to, and that is the thing which makes COM programs nice and simple. Let's look at a very simple one. The classic text on writing programs for the C language says that the first thing you should write is a program which says HELLO, WORLD. when invoked. What's sauce for C is sauce for assembler, so let's start with a HELLO program of our own. My first presentation of this will be bare bones, not stylistically complete, but just an illustration of what an assembler program absolutely has to have: HELLO SEGMENT ;Set up HELLO code and data section ASSUME CS:HELLO,DS:HELLO ;Tell assembler about conditions at entry ORG 100H ;A .COM program begins with 100H byte prefix MAIN: JMP BEGIN ;Control must start here MSG DB 'Hello, world.