💾 Archived View for spam.works › mirrors › textfiles › phreak › delhack.txt captured on 2023-11-14 at 11:19:16.
⬅️ Previous capture (2023-06-16)
-=-=-=-=-=-=-
Deluxe Fone-Code Hacker
Documentation
Congratulations, you now own the best Fone-Code Hacker
around. I have pulled ideas from several sources as well as
plenty of my own to devise this code scanner, most notably:
Peter King for the Carrier Detect variable formula,
Floppy Disk for part of the random selection sequence.
This program is in general release as of 6/12/85,
versions prior to 4.0, were for friends etc for testing
purposes. As of version 4.1 there are no known bugs, however
should you find one, I would appreciate feedback so that I
can correct them.
In the program itself, you will find 4 screens of help
and info, but this is to fill in the blanks that I had no
room to cover.
Basically if you are confused about the three modes, here
is a quick rundown:
SEQENTIAL will start at a code you define like 205100 and try
every code to the ending try that you define like 206700.
You can set it to try every code in that range or every other
or every 3rd etc.
RANDOM will pick random numbers of the length that you
define, length of 5. or 6 or 8 etc. In this mode, you can
set the first digit to use. If you were to set the first
digit to 8 then all codes tried would start with 8 as in:
801245,836501 or to 43 as in 436735,431072. If you set the
first digit to a 2 digit number as in 43 above, when asked
for the length of the code, it is still 6....the program will
recognize that you really are setting the first 2 digits.
SYSTEMATIC is quite esoteric,yet helpful and is almost 2 scanners
in one. I have found it helpful quite often in scanning for a
group of numbers clustered "under" a specific first digit, or to
determine the actual code length.
Scanning First Digit: Here, you set a number of tries and a first
digit range as in 100 tries on digits 2 - 7. What happens is that
the dialer will try 100 random tries as 2xxxxx, then 100 tries as
3xxxxx and 100 tries as 4xxxxx etc...Note that the 100 tries
becomes 600 tries!!!!
Scanning for Code Length: In this fashion, you will set the code
length range to scan as in 4 - 7, which says that you want to scan
a set of 4, 5, 6 and 7 digit codes (as in 2386,45391,587420 and
4756312 respectively). Next, the scanner will apply 50 or 100 or
whatever you specify as number of tries to each code length (100 4
digit tries then 100 5 digit tries etc). Since the object is to
determine the actual code length, the scanning will terminate
after 3 codes are found (just enough to find and verify the
length).
Note that since the number of tries is applied to EACH integer in
the range, the Code Length scanning would be prepared to actually
run 400 codes thru the Service Access Number.
The program should run on any variety of modems as long
as they are 100% Hayes compatible as I utilize several AT
commands. The timer is quite accurate and the scanning
results are accurate. If you turn off the speaker, it remains
off until the end of the program, that is, if you break the
program, the Y/N modem speaker is not a toggle. This is
doubly true with internal, board level modems. On these, if
you break (Ctrl-C, Ctrl-Brk) the program, the modem speaker
will remain off until you send the modem a ATZ. Otherwise
the program will do this for you.
The other thing is that if the screen gets filled with codes
(about 50), and they are cleared to make room for more, there is
no sequence to reprint them as yet. They are therefore lost
unless the disk save or printer is on. They ARE in memeory
(dimension of 250) but there is no recall to screen yet. You
should have such problems.
The scanner could also be used to find 800 extenders by
keying 1800 as the access number, and setting the code length to
7. You would have to listen for probable tones, but it could
be done. This would scan 1800xxxxxxx but could not record a
carrier since there is no target modem.
By the by, the Sequential mode is great for testing. Set the
Access number, then set the first code to try as 1 before a known
code, and end 1 after the known code. Running a known code thru
it will show you the screen,LOF, printer display and/or Disk file
headers.
Some helpful aspects of the dialer: 1) At the end of the
run, the clock will display the time that the the last code
was tried. This is neat if you let it run all by itself, you
can come back to determine how long a given number of codes
take. 2) You can set the dialer to stop after X number of
contacts. This is helpful if you really just want 5 codes
for the month, it will stop when it has that many rather than
dial the remaining tries that you had set. This can help
prevent having a Trouble Card dropped on you for making 4000
800 calls when the last 3000 were not really needed.
*****************************************************************
I do not yet know the program requirements, but this was
written on:
IBM-PC, 2 drives, 512k, DOS 2.0, BASICA
Hayes Modem, Touch tone dialing. It DOES utilize AT commands so
the modem must be Hayes compatible.
Compiled with the BASIC Compiler and converted into .COM with
SPACEMKR.COM (saves about 13% of the space).
****** LEAVE FEEDBACK ON ANY BUGS THAT YOU RUN INTO !!! ******
HELP ACKNOWLEDGEMENTS:
The Floppy Disk *and* Peter King
-Love and Kisses,
The Sorceress KHAIAH