💾 Archived View for spam.works › mirrors › textfiles › music › cheapmid.txt captured on 2023-11-14 at 10:49:53.
⬅️ Previous capture (2023-06-16)
-=-=-=-=-=-=-
The following text explains how to build a MIDI interface for the
Sound Blaster. The circuit is my own design, but works just like
the commercialy available interfaces that retails for $60-$90.
Here is the list of parts necessary:
Qty. Part
1 Sharp PC900 or HP 6N138 opto-isolator
1 DB15P (15 pin 'D' connector, male. like joystick connector)
3 220 ohm resistors (2 for input, 1 for EACH output you need)
1 3 conductor shielded cable (length is up to you)
2 Female 5 pin DIN connector (1 for input, 1 for each output you need)
1 PC board with pre-drilled holes (about 2" x 2" from Radio Shack)
A few short lengths of hook-up wire
All of these parts, except the first 2, are available from Radio Shack.
Construction techniques are completely up to you, if you want to go
ultra-cheap, you don't even need a PC board or enclosure, and you could
use a MIDI cable you already have by cutting it in the middle. I used
a PC900 out of a non-working organ and cut the end off of a joystick I
didn't need and built the whole thing for about $4.00. Buying all the
parts new, and using an enclosure with built-in MIDI jacks may cost
about $20 or so.
Here is a diagram of the DB15P connector (looking at the solder side).
1 5 8
o o o o o o o o
o o o o o o o
9 12 15
Here is the 5 pin FEMALE DIN plug (solder side).
2
5 o 4
o o
3 o o 1
This is the circuit for the MIDI INPUT.
+-----> To pin 5 of 'D' connector
|
To pin 15 of 'D' connector <---+ | +-------+-----> To pin 9 of 'D' con.
| | | |
| 6 |5 |4 \
+---------------+ / 220 ohm
| PC900 | \ resistor
| or | /
| HP 6N138 | |
+---------------+ +------> To pin 6 of PC 900
|1 |2 |3
| | |
\ | +-----> No connection
220 ohm / |
resistor \ |
/ +-----> To pin 5 of DIN connector
|
To pin 4 of DIN connector <----+
Don't overlook the two 220 ohm resistors.
Also, for cables longer than a few feet, connect pin 2 of the DIN to pin
5 of the 'D' connector.
The output circuit is much simpler.
220 ohm resistor
To pin 12 of 'D' connector <---------/\/\/\/\/---------> To pin 5 of DIN con.
To pin 15 of 'D' connector <---------------------------> To pin 4 of DIN con.
Also, for cables longer than a few feet, connect pin 2 of the DIN to pin
5 of the 'D' connector.
This circuit has been built and tested by me, using Voyetra's SPJr, and
a cheap-o Casio keyboard. The input and output do work as shown here, but I
don't have any other MIDI devices to use to test using more than 1 output
device. Theoretically, it should work fine, but it has not been tested.
The chances of hurting anything by trying is slim and none.
This circuit DOES work, but I make no guarantees, nor will I be
held responsible for any damages you may cause from your use of
this information.
If you have any questions, or would like to buy one already built for you,
I can be contacted on:
The Lighthouse BBS (207) 255-3700 (username is Ronald Davis)
The Music Studio BBS (708) 351-0288 (username is Volstagg)