💾 Archived View for spam.works › mirrors › textfiles › computers › tec002.txt captured on 2023-11-14 at 09:14:25.
⬅️ Previous capture (2023-06-14)
-=-=-=-=-=-=-
STAC ELECTRONICS
TECHNICAL SUPPORT BULLETIN
NUMBER: 002
SUBJECT: QEMM386 and OPTIMIZE
DATE: September 18, 1991
SOURCE: STAC Technical Support
SUPERCEDES/ TECH002.DOC dated 8/23/1991
SUPERCEDED BY:
RELEASE STATUS: Public
TITLE: Running OPTIMIZE with Stacker
OVERVIEW: Use this procedure with the Quarterdeck Office Systems program
OPTIMIZE to modify your config.sys and autoexec.bat files to
load all possible programs and drivers into high memory. It is
designed to be used directly from a SSWAPed boot drive.
ISSUES/COMMENTS:
This procedure is for the version of OPTIMIZE that ships with QEMM386 5.x.
It will NOT work with the OPTIMIZE that ships with QEMM386 6.0.
This procedure is NOT necessary if:
1. A Stacker drive is not installed on drive C:, or
2. A Stacker drive installed on drive C: is not being SSWAPed.
For either of these situations, simply OPTIMZE according to the Quarterdeck
instructions.
Stacker version 2.0 users:
If you are using the /sync option to SSWAP, this procedure will cause SSWAP
to ask you if you want to update the changed config.sys and autoexec.bat.
Select No each time you are asked during this procedure. The last time you
boot (in step 11) the files will be identical and you won't be prompted.
RECOMMENDED ACTIONS:
You will need to know which drive letter refers to your boot drive. This
can be determined by running the Stacker utility SWAPMAP. One of the lines
will look like...
Drive x: was drive C: at boot time
What ever letter is "x:" will be the boot drive. in the procedure below,
the boot drive will be referred to as "x:".
IF YOU ARE INSTALLING QEMM FOR THE FIRST TIME...
After booting normally, exit any shell program you may be using and unswap
your boot drive by entering: SSWAP C: x: Then install QEMM.
DO NOT exercise the option to optimize at this time.
STEP 1a IF YOU'VE JUST INSTALLED QEMM...
Assuming you used the default installation options and the QEMM
files are all in C:\QEMM, enter the commands below and reboot the
computer.
MKDIR x:\QEMM
COPY C:\QEMM\*.* x:\QEMM
STEP 1b IF QEMM WAS INSTALLED BEFORE STACKER then enter the command:
COPY C:\QEMM\RSTRCFG.SYS x:\QEMM
STEP 2 Enter the command: COPY x:\CONFIG.SYS C:\
STEP 3 If the Stacker generated autoexec.bat is on drive C:, rename it to
some other name using the REN command. Next copy your autoexec.bat
file to C: by entering: COPY x:\AUTOEXEC.BAT C:\
STEP 4 Run OPTIMIZE. Tell it to go ahead with it's step 1. When it
presents you with the options for step 2, press <ESC> to return to
the DOS prompt.
STEP 5 Enter the following commands.
COPY C:\CONFIG.SYS x:\
COPY C:\OPT2.BAT x:\
COPY C:\AUTOEXEC.BAT x:\AE.BAT
COPY C:\CONFIG.QDK C:\CONFIG.SYS
STEP 6 Reboot the computer. When OPTIMIZE presents you with the options
for step 3, press <ESC> to return to the DOS prompt.
STEP 7 Enter the following commands.
COPY C\CONFIG.QDK C:\CONFIG.SYS
COPY x:\QEMM\LOADHI.OPT C:\QEMM
COPY x:\OPT2.BAT C:\
COPY x:\AE.BAT C:\AUTOEXEC.BAT
STEP 8 Reboot the computer. When OPTIMIZE presents you with the options
for step 3, press <ESC> to return to the DOS prompt.
STEP 9 Enter the following command.
COPY C:\CONFIG.SYS x:\
STEP 10 Reboot the computer.
STEP 11 Enter the following commands, then reboot the computer one last time.
COPY C:\CONFIG.SYS x:\
COPY C:\AUTOEXEC.BAT x:\
STEP 12 If you wish to return to your prior configuration, enter the
following commands.
COPY C:\CONFIG.QDK x:\CONFIG.SYS
COPY C:\AUTOEXEC.QDK C:\AUTOEXEC.BAT