💾 Archived View for gmi.noulin.net › man › man4 › wavelan.4.gmi captured on 2023-11-14 at 09:55:51. Gemini links have been rewritten to link to archived content
⬅️ Previous capture (2022-06-12)
-=-=-=-=-=-=-
WAVELAN(4) Linux Programmer's Manual WAVELAN(4)
NAME
wavelan - AT&T GIS WaveLAN ISA device driver
SYNOPSIS
insmod wavelan_cs.o [io=B,B..] [ irq=I,I..] [name=N,N..]
DESCRIPTION
This driver is obsolete: it was removed from the kernel in version 2.6.35.
wavelan is the low-level device driver for the NCR / AT&T / Lucent WaveLAN ISA and Digital (DEC) RoamAbout DS wireless ethernet adapter. This driver is avail‐
able as a module or might be compiled in the kernel. This driver supports multiple cards in both forms (up to 4) and allocates the next available ethernet de‐
vice (eth0..eth#) for each card found, unless a device name is explicitly specified (see below). This device name will be reported in the kernel log file with
the MAC address, NWID, and frequency used by the card.
Parameters
This section applies to the module form (parameters passed on the insmod(8) command line). If the driver is included in the kernel, use the ether=IRQ,IO,NAME
syntax on the kernel command line.
io Specify the list of base addresses where to search for wavelan cards (setting by dip switch on the card). If you don't specify any io address, the driver
will scan 0x390 and 0x3E0 addresses, which might conflict with other hardware...
irq Set the list of IRQs that each wavelan card should use (the value is saved in permanent storage for future use).
name Set the list of names to be used for each wavelan card device (name used by ifconfig(8)).
Wireless extensions
Use iwconfig(8) to manipulate wireless extensions.
NWID (or domain)
Set the network ID [0 to FFFF] or disable it [off]. As the NWID is stored in the card Permanent Storage Area, it will be reused at any further invocation of the
driver.
Frequency & channels
For the 2.4 GHz 2.00 Hardware, you are able to set the frequency by specifying one of the 10 defined channels (2.412, 2.422, 2.425, 2.4305, 2.432, 2.442, 2.452,
2.460, 2.462 or 2.484) or directly as a numeric value. The frequency is changed immediately and permanently. Frequency availability depends on the regula‐
tions...
Statistics spy
Set a list of MAC addresses in the driver (up to 8) and get the last quality of link for each of those (see iwspy(8)).
/proc/net/wireless
status is the status reported by the modem. Link quality reports the quality of the modulation on the air (direct sequence spread spectrum) [max = 16]. Level
and Noise refer to the signal level and noise level [max = 64]. The crypt discarded packet and misc discarded packet counters are not implemented.
Private ioctl
You may use iwpriv(8) to manipulate private ioctls.
Quality and level threshold
Enables you to define the quality and level threshold used by the modem (packet below that level are discarded).
Histogram
This functionality makes it possible to set a number of signal level intervals and to count the number of packets received in each of those defined intervals.
This distribution might be used to calculate the mean value and standard deviation of the signal level.
Specific notes
This driver fails to detect some non-NCR/AT&T/Lucent Wavelan cards. If this happens for you, you must look in the source code on how to add your card to the de‐
tection routine.
Some of the mentioned features are optional. You may enable to disable them by changing flags in the driver header and recompile.
SEE ALSO
wavelan_cs(4), ifconfig(8), insmod(8), iwconfig(8), iwpriv(8), iwspy(8)
Linux 2021-03-22 WAVELAN(4)