💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc6850.txt captured on 2023-09-28 at 18:40:50.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Internet Engineering Task Force (IETF) A. Rijhsinghani
Request for Comments: 6850 Hewlett-Packard
Category: Standards Track K. Zebrose
ISSN: 2070-1721 HW Embedded
January 2013
Definitions of Managed Objects for Routing Bridges (RBridges)
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols. In particular, it defines
objects for managing a Routing Bridge (RBridge), also known as a
TRILL Switch, based on the IETF TRILL (Transparent Interconnection of
Lots of Links) protocol.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc6850.
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Rijhsinghani & Zebrose Standards Track [Page 1]
RFC 6850 RBridges: TRILL Base MIB January 2013
Table of Contents
1. Introduction ....................................................2
2. The Internet-Standard Management Framework ......................3
3. Overview ........................................................3
4. Conventions .....................................................4
5. Structure of the MIB Module .....................................4
5.1. Textual Conventions ........................................4
5.2. The rbridgeBase Subtree ....................................4
5.3. The rbridgeFdb Subtree .....................................4
5.4. The rbridgeVlan Subtree ....................................4
5.5. The rbridgeEsadi Subtree ...................................4
5.6. The rbridgeCounters Subtree ................................4
5.7. The rbridgeSnooping Subtree ................................5
5.8. The rbridgeDtree Subtree ...................................5
5.9. The rbridgeTrill Subtree ...................................5
5.10. The Notifications Subtree .................................5
6. Relationship to Other MIB Modules ...............................5
6.1. Relationship to IF-MIB .....................................5
6.2. Relationship to BRIDGE-MIB .................................6
6.3. Relationship to P-BRIDGE-MIB ...............................6
6.4. Relationship to Q-BRIDGE-MIB ...............................6
6.5. Relationship to IEEE8021-BRIDGE-MIB ........................7
6.6. Relationship to IEEE8021-Q-BRIDGE-MIB ......................7
6.7. Relationship to ISIS-MIB ...................................8
6.8. MIB Modules Required for IMPORTS ...........................8
7. Definition of the RBridge MIB Module ............................9
8. Security Considerations ........................................55
9. IANA Considerations ............................................56
10. Contributors ..................................................56
11. References ....................................................57
11.1. Normative References .....................................57
11.2. Informative References ...................................58
1. Introduction
This document describes a model for managing Routing Bridges
(RBridges), also known as TRILL Switches, as defined in [RFC6325].
RBridges provide optimal pair-wise forwarding without configuration
using IS-IS routing and encapsulation of traffic. RBridges are
compatible with previous IEEE 802.1 customer bridges as well as IPv4
and IPv6 routers and end nodes. They are as invisible to current IP
routers as bridges are and, like routers, they terminate the bridge
spanning tree protocol. In creating an RBridge management model, the
device is viewed primarily as a customer bridge. For a discussion of
the problem addressed by TRILL (Transparent Interconnection of Lots
of Links), see [RFC5556].
Rijhsinghani & Zebrose Standards Track [Page 2]
RFC 6850 RBridges: TRILL Base MIB January 2013
RBridges support features specified for transparent bridges in
IEEE 802.1, and the corresponding MIB modules are used to manage
those features. For IS-IS purposes, the corresponding MIB module is
used to manage the protocol. This MIB module specifies those objects
that are TRILL-specific and hence not available in other MIB modules.
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
3. Overview
The RBridge MIB module is intended as an overall framework for
managing RBridges, also known as TRILL Switches. Where possible, the
MIB references existing MIB definitions in order to maximize reuse.
This results in a considerable emphasis on the relationship with
other MIB modules.
Starting with the physical interfaces, there are requirements for
certain elements of the IF-MIB to be implemented. These elements are
required in order to connect the per-port parameters to higher-level
functions of the physical device.
Transparent bridging, VLANs, traffic classes, and multicast filtering
are supported by the TRILL protocol, and the corresponding management
is expected to conform to the BRIDGE-MIB module [RFC4188] and to the
P-BRIDGE-MIB and Q-BRIDGE-MIB modules [RFC4363].
The IS-IS routing protocol is used in order to determine the optimum
pair-wise forwarding path. This protocol is managed using the IS-IS
MIB module defined in [RFC4444]. Since the TRILL protocol specifies
the use of a single level and a fixed area address of zero, some
IS-IS MIB objects are not applicable. Some IS-IS MIB objects are
used in the TRILL protocol.
Rijhsinghani & Zebrose Standards Track [Page 3]
RFC 6850 RBridges: TRILL Base MIB January 2013
4. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
RFC 2119 [RFC2119].
5. Structure of the MIB Module
Objects in this MIB module are arranged into subtrees. Each subtree
is organized as a set of related objects. The various subtrees are
shown below. These are supplemented with required elements of the
IF-MIB, ISIS-MIB, BRIDGE-MIB, P-BRIDGE-MIB, Q-BRIDGE-MIB, and IEEE
Bridge MIB modules.
5.1. Textual Conventions
Textual conventions are defined to represent object types relevant to
TRILL.
5.2. The rbridgeBase Subtree
This subtree contains system- and port-specific objects applicable to
all RBridges.
5.3. The rbridgeFdb Subtree
This subtree contains objects applicable to the forwarding database
used by the RBridge in making packet-forwarding decisions. Because
it contains additional information used by the TRILL protocol not
applicable to 802.1D/Q bridges, it is a superset of the corresponding
subtrees defined in the BRIDGE-MIB and Q-BRIDGE-MIB.
5.4. The rbridgeVlan Subtree
This subtree describes objects applicable to VLANs configured on the
RBridge.
5.5. The rbridgeEsadi Subtree
This subtree describes objects relevant to RBridges that support the
optional End-Station Address Distribution Information (ESADI)
protocol.
5.6. The rbridgeCounters Subtree
This subtree contains statistics maintained by RBridges that can aid
in monitoring and troubleshooting networks connected by them.
Rijhsinghani & Zebrose Standards Track [Page 4]
RFC 6850 RBridges: TRILL Base MIB January 2013
5.7. The rbridgeSnooping Subtree
This subtree describes objects applicable to RBridges capable of
snooping IPv4 and/or IPv6 multicast control frames and pruning IP
multicast traffic based on detection of IP multicast routers and
listeners.
5.8. The rbridgeDtree Subtree
This subtree contains objects relevant to distribution trees computed
by RBridges for the forwarding of multi-destination frames.
5.9. The rbridgeTrill Subtree
This subtree contains objects applicable to the TRILL IS-IS protocol,
beyond what is available in the ISIS-MIB.
5.10. The Notifications Subtree
The defined notifications are focused on the TRILL protocol
functionality. Notifications are defined for changes in the
Designated RBridge status and the topology.
6. Relationship to Other MIB Modules
The IF-MIB, BRIDGE-MIB, P-BRIDGE-MIB, Q-BRIDGE-MIB,
IEEE8021-BRIDGE-MIB, IEEE8021-Q-BRIDGE-MIB, and ISIS-MIB modules all
contain objects relevant to the RBridge MIB. Management objects
contained in these modules are not duplicated here, to reduce overlap
to the extent possible.
The Bridge MIB modules were originally written in the IETF and
implemented by many vendors. Per [RFC4663], this has recently been
transferred to the IEEE 802.1 working group. As vendors may have
implemented either the IETF or IEEE Bridge MIB modules, this RBridge
MIB module is designed to work with either one.
6.1. Relationship to IF-MIB
The port identification elements MUST be implemented in order to
allow them to be cross-referenced. The Interfaces MIB [RFC2863]
requires that any MIB module that is an adjunct of the Interfaces MIB
clarify specific areas within the Interfaces MIB module. These areas
were intentionally left vague in the Interfaces MIB module to avoid
over-constraining the MIB, thereby precluding management of certain
media types. Section 4 of [RFC2863] enumerates several areas that a
Rijhsinghani & Zebrose Standards Track [Page 5]
RFC 6850 RBridges: TRILL Base MIB January 2013
media-specific MIB module must clarify. The implementor is referred
to [RFC2863] in order to understand the general intent of these
areas.
6.2. Relationship to BRIDGE-MIB
The following subtrees in the BRIDGE-MIB [RFC4188] contain
information relevant to RBridges when the corresponding functionality
is implemented.
o dot1dBase
o dot1dTp
o dot1dStatic
6.3. Relationship to P-BRIDGE-MIB
The following subtrees in the P-BRIDGE-MIB [RFC4363] contain
information relevant to RBridges when the corresponding functionality
is implemented.
o dot1dExtBase
o dot1dPriority
o dot1dGarp
o dot1dGmrp
o dot1dTpHCPortTable
o dot1dTpPortOverflowTable
6.4. Relationship to Q-BRIDGE-MIB
The following groups in the Q-BRIDGE-MIB [RFC4363] contain
information relevant to RBridges when the corresponding functionality
is implemented. This functionality is also contained in the
IEEE8021-Q-BRIDGE-MIB.
o dot1qBase
o dot1qTp
o dot1qStatic
Rijhsinghani & Zebrose Standards Track [Page 6]
RFC 6850 RBridges: TRILL Base MIB January 2013
o dot1qVlan
o dot1vProtocol
6.5. Relationship to IEEE8021-BRIDGE-MIB
The following subtrees in the IEEE8021-BRIDGE-MIB contain information
relevant to RBridges when the corresponding functionality is
implemented.
o ieee8021BridgeBase
o ieee8021BridgeTp
o ieee8021BridgePriority
o ieee8021BridgeMrp
o ieee8021BridgeMmrp
o ieee8021BridgeInternalLan
o ieee8021BridgeDot1d
6.6. Relationship to IEEE8021-Q-BRIDGE-MIB
The following subtrees in the IEEE8021-Q-BRIDGE-MIB contain
information relevant to RBridges when the corresponding functionality
is implemented.
o ieee8021QBridgeBase
o ieee8021QBridgeTp
o ieee8021QBridgeStatic
o ieee8021QBridgeVlan
o ieee8021QBridgeProtocol
Rijhsinghani & Zebrose Standards Track [Page 7]
RFC 6850 RBridges: TRILL Base MIB January 2013
6.7. Relationship to ISIS-MIB
"Management Information Base for Intermediate System to Intermediate
System (IS-IS)" [RFC4444] defines a MIB module for the IS-IS routing
protocol when it is used to construct routing tables for IP networks.
While most of these objects are applicable to the TRILL layer 2
implementation, note the IS-IS constraints for the current version of
TRILL [RFC6325]:
o The TRILL IS-IS instance uses a single Level 1 IS-IS area.
o The TRILL Level 1 IS-IS area uses the fixed area address zero.
o The TRILL IS-IS instance is not used for IP address advertisement.
o The TRILL IS-IS instance is used for only a single protocol:
TRILL.
Accordingly, tables that report IP address reachability and tables
that allow configuration or reporting of multiple IS-IS areas,
multiple IS-IS levels, or multiple protocols will be empty in the
ISIS-MIB module for the current version of TRILL.
Note also that when more than one instance of the IS-IS protocol is
running on a device, as in the case of a device performing both
RBridge and IS-IS IP router functions, multiple instances of the
ISIS-MIB module can be distinguished by the use of SNMPv3 contexts or
SNMPv1 communities.
6.8. MIB Modules Required for IMPORTS
The following MIB module imports objects from the SNMPv2-SMI
[RFC2578], SNMPv2-TC [RFC2579], SNMPv2-CONF [RFC2580], IF-MIB
[RFC2863], INET-ADDRESS-MIB [RFC4001], BRIDGE-MIB [RFC4188],
and Q-BRIDGE-MIB [RFC4363]. (The IEEE Bridge MIB modules import
similar TCs.)
Rijhsinghani & Zebrose Standards Track [Page 8]
RFC 6850 RBridges: TRILL Base MIB January 2013
7. Definition of the RBridge MIB Module
RBRIDGE-MIB DEFINITIONS ::= BEGIN
-- ---------------------------------------------------------- --
-- MIB for RBRIDGE devices, also known as TRILL Switches
-- ---------------------------------------------------------- --
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
Counter32, Counter64, Unsigned32, mib-2
FROM SNMPv2-SMI -- RFC2578
TEXTUAL-CONVENTION, TruthValue, MacAddress, RowStatus
FROM SNMPv2-TC -- RFC2579
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF -- RFC2580
VlanId, PortList
FROM Q-BRIDGE-MIB -- RFC4363
InetAddress, InetAddressType
FROM INET-ADDRESS-MIB -- RFC4001
BridgeId
FROM BRIDGE-MIB -- RFC4188
InterfaceIndex
FROM IF-MIB -- RFC2863
;
rbridgeMIB MODULE-IDENTITY
LAST-UPDATED "201301070000Z"
ORGANIZATION "IETF TRILL Working Group"
CONTACT-INFO
"http://datatracker.ietf.org/wg/trill/charter/
Email: trill@ietf.org
Anil Rijhsinghani
Hewlett-Packard
Tel: +1 508 323 1251
Email: anil@charter.net
Kate Zebrose
HW Embedded
Tel: +1 617 840 9673
Email: zebrose@alum.mit.edu"
DESCRIPTION
"The RBridge MIB module for managing switches that support
the TRILL protocol."
REVISION "201301070000Z"
Rijhsinghani & Zebrose Standards Track [Page 9]
RFC 6850 RBridges: TRILL Base MIB January 2013
DESCRIPTION
"Initial version, published as RFC 6850.
Copyright (c) 2013 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject to
the license terms contained in, the Simplified BSD License set
forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info)."
::= { mib-2 214 }
-- ---------------------------------------------------------- --
-- Subtrees in the RBridge MIB
-- ---------------------------------------------------------- --
rbridgeNotifications OBJECT IDENTIFIER ::= { rbridgeMIB 0 }
rbridgeObjects OBJECT IDENTIFIER ::= { rbridgeMIB 1 }
rbridgeConformance OBJECT IDENTIFIER ::= { rbridgeMIB 2 }
rbridgeBase OBJECT IDENTIFIER ::= { rbridgeObjects 1 }
rbridgeFdb OBJECT IDENTIFIER ::= { rbridgeObjects 2 }
rbridgeVlan OBJECT IDENTIFIER ::= { rbridgeObjects 3 }
rbridgeEsadi OBJECT IDENTIFIER ::= { rbridgeObjects 4 }
rbridgeCounter OBJECT IDENTIFIER ::= { rbridgeObjects 5 }
rbridgeSnooping OBJECT IDENTIFIER ::= { rbridgeObjects 6 }
rbridgeDtree OBJECT IDENTIFIER ::= { rbridgeObjects 7 }
rbridgeTrill OBJECT IDENTIFIER ::= { rbridgeObjects 8 }
-- ---------------------------------------------------------- --
-- Type Definitions
-- ---------------------------------------------------------- --
RbridgeAddress ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1x:"
STATUS current
DESCRIPTION
"The Media Access Control (MAC) address used by an RBridge
port. This may match the RBridge IS-IS SystemID."
SYNTAX OCTET STRING (SIZE (6))
Rijhsinghani & Zebrose Standards Track [Page 10]
RFC 6850 RBridges: TRILL Base MIB January 2013
RbridgeNickname ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The 16-bit identifier used in TRILL as an
abbreviation for the RBridge's 48-bit IS-IS System ID.
The value 0 means a nickname is not specified, the values
0xFFC0 through 0xFFFE are reserved for future allocation,
and the value 0xFFFF is permanently reserved."
REFERENCE
"RFC 6325, Section 3.7"
SYNTAX Unsigned32 (0..65471)
--
-- the rbridgeBase subtree
--
-- Implementation of the rbridgeBase subtree is mandatory for all
-- RBridges.
--
rbridgeBaseTrillVersion OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum TRILL version number that this RBridge
supports."
REFERENCE
"RFC 6325, Section 3.2"
::= { rbridgeBase 1 }
rbridgeBaseNumPorts OBJECT-TYPE
SYNTAX Unsigned32
UNITS "ports"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of ports controlled by this RBridge."
REFERENCE
"RFC 6325, Section 2.6.1"
::= { rbridgeBase 2 }
rbridgeBaseForwardDelay OBJECT-TYPE
SYNTAX Unsigned32 (4..30)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
Rijhsinghani & Zebrose Standards Track [Page 11]
RFC 6850 RBridges: TRILL Base MIB January 2013
DESCRIPTION
"Modified aging time for address entries after an appointed
forwarder change.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.8.3"
::= { rbridgeBase 3 }
rbridgeBaseUniMultipathEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The enabled status of unicast TRILL multipathing.
It is enabled when true.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Appendix C"
::= { rbridgeBase 4 }
rbridgeBaseMultiMultipathEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The enabled status of multi-destination TRILL multipathing.
It is enabled when true.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Appendix C"
::= { rbridgeBase 5 }
rbridgeBaseAcceptEncapNonadj OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Accept TRILL-encapsulated frames from a neighbor with which
this RBridge does not have an IS-IS adjacency, when the value
of this object is 'true'.
Rijhsinghani & Zebrose Standards Track [Page 12]
RFC 6850 RBridges: TRILL Base MIB January 2013
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.6.2"
::= { rbridgeBase 6 }
rbridgeBaseNicknameNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..256)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of nicknames this RBridge should acquire.
These can be acquired dynamically or configured
statically. This value represents the maximum
number of entries in rbridgeBaseNicknameTable.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 3.7.3"
::= { rbridgeBase 7 }
-- ---------------------------------------------------------- --
-- The RBridge Base Nickname Table
-- ---------------------------------------------------------- --
rbridgeBaseNicknameTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeBaseNicknameEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about nicknames
configured by an operator or learned dynamically
by this RBridge."
REFERENCE
"RFC 6325, Section 3.7"
::= { rbridgeBase 8 }
rbridgeBaseNicknameEntry OBJECT-TYPE
SYNTAX RbridgeBaseNicknameEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information for each nickname of the RBridge."
REFERENCE
"RFC 6325, Section 3.7"
INDEX { rbridgeBaseNicknameName }
::= { rbridgeBaseNicknameTable 1 }
Rijhsinghani & Zebrose Standards Track [Page 13]
RFC 6850 RBridges: TRILL Base MIB January 2013
RbridgeBaseNicknameEntry ::=
SEQUENCE {
rbridgeBaseNicknameName
RbridgeNickname,
rbridgeBaseNicknamePriority
Unsigned32,
rbridgeBaseNicknameDtrPriority
Unsigned32,
rbridgeBaseNicknameType
INTEGER,
rbridgeBaseNicknameRowStatus
RowStatus
}
rbridgeBaseNicknameName OBJECT-TYPE
SYNTAX RbridgeNickname
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Nicknames are 16-bit quantities that act as
abbreviations for RBridge's 48-bit IS-IS System ID to
achieve a more compact encoding."
REFERENCE
"RFC 6325, Section 3.7"
::= { rbridgeBaseNicknameEntry 1 }
rbridgeBaseNicknamePriority OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This RBridge's priority to hold this nickname. When
the nickname is configured, the default value of this
object is 192. When the nickname is configured, the most
significant bit (0x80) must be set and the bottom 7 bits
have the default value of 0x40, so 0x80 + 0x40 == 0xC0,
which is 192 decimal. Additionally, the bottom 7 bits
could be configured to a value other than 0x40.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 3.7"
DEFVAL { 192 }
::= { rbridgeBaseNicknameEntry 2 }
Rijhsinghani & Zebrose Standards Track [Page 14]
RFC 6850 RBridges: TRILL Base MIB January 2013
rbridgeBaseNicknameDtrPriority OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The distribution tree root priority for this nickname.
The default value of this object is 32768.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.5"
DEFVAL { 32768 }
::= { rbridgeBaseNicknameEntry 3 }
rbridgeBaseNicknameType OBJECT-TYPE
SYNTAX INTEGER {
static(1),
dynamic(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the status of the entry. The
default value is static(1).
static(1) - this entry has been configured and
will remain after the next reset of the RBridge.
dynamic(2) - this entry has been acquired by the
RBridge nickname acquisition protocol."
REFERENCE
"RFC 6325, Section 3.7"
DEFVAL { static }
::= { rbridgeBaseNicknameEntry 4 }
rbridgeBaseNicknameRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the status of the entry."
::= { rbridgeBaseNicknameEntry 5 }
Rijhsinghani & Zebrose Standards Track [Page 15]
RFC 6850 RBridges: TRILL Base MIB January 2013
-- ---------------------------------------------------------- --
-- The RBridge Port Table
-- ---------------------------------------------------------- --
rbridgeBasePortTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeBasePortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains generic information about every
port that is associated with this RBridge."
REFERENCE
"RFC 6325, Section 5.3"
::= { rbridgeBase 9 }
rbridgeBasePortEntry OBJECT-TYPE
SYNTAX RbridgeBasePortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information for each port of the bridge."
REFERENCE
"RFC 6325, Section 5.3"
INDEX { rbridgeBasePort }
::= { rbridgeBasePortTable 1 }
RbridgeBasePortEntry ::=
SEQUENCE {
rbridgeBasePort
Unsigned32,
rbridgeBasePortIfIndex
InterfaceIndex,
rbridgeBasePortDisable
TruthValue,
rbridgeBasePortTrunkPort
TruthValue,
rbridgeBasePortAccessPort
TruthValue,
rbridgeBasePortP2pHellos
TruthValue,
rbridgeBasePortState
INTEGER,
rbridgeBasePortInhibitionTime
Unsigned32,
rbridgeBasePortDisableLearning
TruthValue,
rbridgeBasePortDesiredDesigVlan
VlanId,
Rijhsinghani & Zebrose Standards Track [Page 16]
RFC 6850 RBridges: TRILL Base MIB January 2013
rbridgeBasePortDesigVlan
VlanId,
rbridgeBasePortStpRoot
BridgeId,
rbridgeBasePortStpRootChanges
Counter32,
rbridgeBasePortStpWiringCloset
BridgeId
}
rbridgeBasePort OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The port number of the port for which this entry
contains RBridge management information."
REFERENCE
"RFC 6325, Section 5.3"
::= { rbridgeBasePortEntry 1 }
rbridgeBasePortIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the instance of the ifIndex object,
defined in the IF-MIB, for the interface corresponding
to this port. The RBridge port sits on top of
this interface."
::= { rbridgeBasePortEntry 2 }
rbridgeBasePortDisable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Disable port bit. When this bit is set (true), all frames
received or to be transmitted are discarded, with the
possible exception of some layer 2 control frames that may
be generated and transmitted or received and processed
locally. Default value is 'false'.
The value of this object MUST be retained across
re-initializations of the management system."
Rijhsinghani & Zebrose Standards Track [Page 17]
RFC 6850 RBridges: TRILL Base MIB January 2013
REFERENCE
"RFC 6325, Section 4.9.1"
DEFVAL { false }
::= { rbridgeBasePortEntry 3 }
rbridgeBasePortTrunkPort OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"End-station service disable (trunk port) bit. When this bit
is set (true), all native frames received on the port and all
native frames that would have been sent on the port are
discarded. Default value is 'false'.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.9.1"
DEFVAL { false }
::= { rbridgeBasePortEntry 4 }
rbridgeBasePortAccessPort OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"TRILL traffic disable (access port) bit. If this bit is
set, the goal is to avoid sending any TRILL frames, except
TRILL-Hello frames, on the port, since it is intended only
for native end-station traffic. This ensures that the link
is not on the shortest path for any destination. Default
value is 'false'.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.9.1"
DEFVAL { false }
::= { rbridgeBasePortEntry 5 }
rbridgeBasePortP2pHellos OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Use point-to-point (P2P) Hellos bit. If this bit is set,
Hellos sent on this port are IS-IS P2P Hellos, not the
Rijhsinghani & Zebrose Standards Track [Page 18]
RFC 6850 RBridges: TRILL Base MIB January 2013
default TRILL-Hellos. In addition, the IS-IS P2P three-way
handshake is used on P2P RBridge links. Default value is
'false'.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.9.1"
DEFVAL { false }
::= { rbridgeBasePortEntry 6 }
rbridgeBasePortState OBJECT-TYPE
SYNTAX INTEGER {
uninhibited(1),
portInhibited(2),
vlanInhibited(3),
disabled(4),
broken(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The port's current state. If the entire port is
inhibited, its state is portInhibited(2). If specific VLANs
are inhibited, the state is vlanInhibited(3), and
rbridgeVlanPortTable will tell which VLANs are inhibited.
For ports that are disabled (see rbridgeBasePortDisable),
this object will have a value of disabled(4). If the
RBridge has detected a port that is malfunctioning, it will
place that port into the broken(5) state."
REFERENCE
"RFC 6325, Section 4.2.4.3"
::= { rbridgeBasePortEntry 7 }
rbridgeBasePortInhibitionTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time in seconds that this RBridge will inhibit forwarding
on this port after it observes a spanning tree root bridge
change on a link or receives conflicting VLAN forwarder
information. The default value is 30.
The value of this object MUST be retained across
re-initializations of the management system."
Rijhsinghani & Zebrose Standards Track [Page 19]
RFC 6850 RBridges: TRILL Base MIB January 2013
REFERENCE
"RFC 6325, Section 4.2.4.3"
DEFVAL { 30 }
::= { rbridgeBasePortEntry 8 }
rbridgeBasePortDisableLearning OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Disable learning of MAC addresses seen on this port.
To disable learning, the value of this object must be
set to 'true'. The default is 'false'.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.8"
DEFVAL { false }
::= { rbridgeBasePortEntry 9 }
rbridgeBasePortDesiredDesigVlan OBJECT-TYPE
SYNTAX VlanId
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VLAN that a Designated RBridge (DRB) will specify in
its TRILL-Hellos as the VLAN to be used by all RBridges on
the link for TRILL frames. This VLAN must be enabled on
this port.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.4.3"
::= { rbridgeBasePortEntry 10 }
rbridgeBasePortDesigVlan OBJECT-TYPE
SYNTAX VlanId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The VLAN being used on this link for TRILL frames."
REFERENCE
"RFC 6325, Section 4.4.3"
::= { rbridgeBasePortEntry 11 }
Rijhsinghani & Zebrose Standards Track [Page 20]
RFC 6850 RBridges: TRILL Base MIB January 2013
rbridgeBasePortStpRoot OBJECT-TYPE
SYNTAX BridgeId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bridge identifier of the root of the spanning tree,
as learned from a Bridge PDU (BPDU) received on this port.
For the Multiple Spanning Tree Protocol (MSTP), this is
the root bridge of the Common and Internal Spanning Tree
(CIST). If no BPDU has been heard, the value returned
is a string of zeros."
REFERENCE
"RFC 6325, Section 4.2.4.3"
::= { rbridgeBasePortEntry 12 }
rbridgeBasePortStpRootChanges OBJECT-TYPE
SYNTAX Counter32
UNITS "changes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a change in the root bridge is seen from
spanning tree BPDUs received on this port, indicating a
change in bridged LAN topology. Each such change may cause
the port to be inhibited for a period of time. This counter
should be synchronized with ifCounterDiscontinuityTime.
Discontinuities in the value of this counter can occur
at re-initialization of the management system."
REFERENCE
"RFC 6325, Section 4.9.3.2"
::= { rbridgeBasePortEntry 13 }
rbridgeBasePortStpWiringCloset OBJECT-TYPE
SYNTAX BridgeId
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Bridge ID to be used as the spanning tree root in BPDUs
sent for the Wiring Closet topology solution described in
[RFC6325]. Note that the same value of this object must be
set on all RBridge ports participating in this solution.
The default value is all 0s. A non-zero value configured
into this object indicates that this solution is in use.
The value of this object MUST be retained across
re-initializations of the management system."
Rijhsinghani & Zebrose Standards Track [Page 21]
RFC 6850 RBridges: TRILL Base MIB January 2013
REFERENCE
"RFC 6325, Appendix A.3.3"
::= { rbridgeBasePortEntry 14 }
-- -------------------------------------------------------------
-- RBridge Forwarding Database
-- -------------------------------------------------------------
rbridgeConfidenceNative OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The confidence level associated with MAC addresses
learned from native frames. This is applicable to
all RBridge ports.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.8.1"
::= { rbridgeFdb 1 }
rbridgeConfidenceDecap OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The confidence level associated with inner MAC addresses
learned after decapsulation of a TRILL data frame.
This is applicable to all RBridge ports.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.8.1"
::= { rbridgeFdb 2 }
rbridgeConfidenceStatic OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The confidence level associated with MAC addresses that
are statically configured. The default value is 255.
The value of this object MUST be retained across
re-initializations of the management system."
Rijhsinghani & Zebrose Standards Track [Page 22]
RFC 6850 RBridges: TRILL Base MIB January 2013
REFERENCE
"RFC 6325, Section 4.8.2"
DEFVAL { 255 }
::= { rbridgeFdb 3 }
-- -------------------------------------------------------------
-- Multiple Forwarding Databases for RBridges
--
-- This allows for an instance per FdbId, as defined in the
-- Bridge MIB.
--
-- Each VLAN may have an independent FDB, or multiple VLANs may
-- share one.
-- -------------------------------------------------------------
rbridgeUniFdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeUniFdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about unicast entries
for which the device has forwarding and/or filtering
information. This information is used by the
transparent bridging function in determining how to
propagate a received frame."
REFERENCE
"RFC 6325, Section 4.8"
::= { rbridgeFdb 4 }
rbridgeUniFdbEntry OBJECT-TYPE
SYNTAX RbridgeUniFdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a specific unicast MAC address for
which the RBridge has some forwarding and/or filtering
information."
INDEX { rbridgeFdbId, rbridgeUniFdbAddr }
::= { rbridgeUniFdbTable 1 }
RbridgeUniFdbEntry ::=
SEQUENCE {
rbridgeFdbId
Unsigned32,
rbridgeUniFdbAddr
MacAddress,
Rijhsinghani & Zebrose Standards Track [Page 23]
RFC 6850 RBridges: TRILL Base MIB January 2013
rbridgeUniFdbPort
Unsigned32,
rbridgeUniFdbNickname
RbridgeNickname,
rbridgeUniFdbConfidence
Unsigned32,
rbridgeUniFdbStatus
INTEGER
}
rbridgeFdbId OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identity of this Filtering Database."
::= { rbridgeUniFdbEntry 1 }
rbridgeUniFdbAddr OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unicast MAC address for which the device has
forwarding information."
::= { rbridgeUniFdbEntry 2 }
rbridgeUniFdbPort OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Either the value '0', or the RBridge port number of the
port on which a frame having a source address equal to the
value of the corresponding instance of rbridgeUniFdbAddr
has been seen. A value of '0' indicates that the port
number has not been learned but that the device does have
some information about this MAC address.
Implementors are encouraged to assign the port value to
this object whenever it is available, even for addresses
for which the corresponding value of rbridgeUniFdbStatus is
not learned(3)."
::= { rbridgeUniFdbEntry 3 }
rbridgeUniFdbNickname OBJECT-TYPE
SYNTAX RbridgeNickname
MAX-ACCESS read-only
Rijhsinghani & Zebrose Standards Track [Page 24]
RFC 6850 RBridges: TRILL Base MIB January 2013
STATUS current
DESCRIPTION
"The RBridge nickname that is placed in the egress
nickname field of a TRILL frame sent to this
rbridgeFdbAddress in this rbridgeFdbId."
REFERENCE
"RFC 6325, Section 4.8.1"
::= { rbridgeUniFdbEntry 4 }
rbridgeUniFdbConfidence OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The confidence level associated with this entry."
REFERENCE
"RFC 6325, Section 4.8.1"
::= { rbridgeUniFdbEntry 5 }
rbridgeUniFdbStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
invalid(2),
learned(3),
self(4),
mgmt(5),
esadi(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of this entry. The meanings of the values
are:
other(1) - none of the following.
invalid(2) - this entry is no longer valid (e.g., it
was learned but has since aged out) but has not
yet been flushed from the table.
learned(3) - the information in this entry was learned
and is being used.
self(4) - the value of the corresponding instance of
rbridgeFdbAddress represents one of the device's
addresses. The corresponding instance of
rbridgeFdbPort indicates which of the device's
ports has this address.
Rijhsinghani & Zebrose Standards Track [Page 25]
RFC 6850 RBridges: TRILL Base MIB January 2013
mgmt(5) - the value of the corresponding instance of
rbridgeFdbAddress was configured by management.
esadi(6) - the value of the corresponding instance of
rbridgeFdbAddress was learned from ESADI."
::= { rbridgeUniFdbEntry 6 }
-- -------------------------------------------------------------
-- RBridge Forwarding Information Base (FIB)
-- -------------------------------------------------------------
rbridgeUniFibTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeUniFibEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about nicknames known by
the RBridge. If Equal-Cost Multipath (ECMP) is implemented,
there are as many entries for a nickname as there are ECMP
paths available for it."
::= { rbridgeFdb 5 }
rbridgeUniFibEntry OBJECT-TYPE
SYNTAX RbridgeUniFibEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information about nicknames known by the RBridge.
If ECMP is implemented, there are as many entries as there
are ECMP paths available for a given nickname."
INDEX { rbridgeUniFibNickname, rbridgeUniFibPort,
rbridgeUniFibNextHop }
::= { rbridgeUniFibTable 1 }
RbridgeUniFibEntry ::=
SEQUENCE {
rbridgeUniFibNickname
RbridgeNickname,
rbridgeUniFibPort
Unsigned32,
rbridgeUniFibNextHop
RbridgeNickname,
rbridgeUniFibHopCount
Unsigned32
}
rbridgeUniFibNickname OBJECT-TYPE
SYNTAX RbridgeNickname
MAX-ACCESS not-accessible
Rijhsinghani & Zebrose Standards Track [Page 26]
RFC 6850 RBridges: TRILL Base MIB January 2013
STATUS current
DESCRIPTION
"An RBridge nickname for which this RBridge has
forwarding information."
::= { rbridgeUniFibEntry 1 }
rbridgeUniFibPort OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The RBridge port number of the port attached to the
next-hop RBridge for the path towards the RBridge whose
nickname is specified in this entry."
::= { rbridgeUniFibEntry 2 }
rbridgeUniFibNextHop OBJECT-TYPE
SYNTAX RbridgeNickname
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The nickname of the next-hop RBridge for the path
towards the RBridge whose nickname is specified in this
entry."
::= { rbridgeUniFibEntry 3 }
rbridgeUniFibHopCount OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The hop count from this ingress RBridge to the egress
RBridge whose nickname is specified in
rbridgeUniFibNickname."
::= { rbridgeUniFibEntry 4 }
rbridgeMultiFibTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeMultiFibEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about egress nicknames
used for multi-destination frame forwarding by this
RBridge."
::= { rbridgeFdb 6 }
Rijhsinghani & Zebrose Standards Track [Page 27]
RFC 6850 RBridges: TRILL Base MIB January 2013
rbridgeMultiFibEntry OBJECT-TYPE
SYNTAX RbridgeMultiFibEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information about egress nicknames used for
multi-destination frame forwarding by this RBridge."
INDEX { rbridgeMultiFibNickname }
::= { rbridgeMultiFibTable 1 }
RbridgeMultiFibEntry ::=
SEQUENCE {
rbridgeMultiFibNickname
RbridgeNickname,
rbridgeMultiFibPorts
PortList
}
rbridgeMultiFibNickname OBJECT-TYPE
SYNTAX RbridgeNickname
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The nickname of the multicast distribution tree."
::= { rbridgeMultiFibEntry 1 }
rbridgeMultiFibPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The list of ports to which a frame destined to this
multicast distribution tree is flooded. This may be pruned
further based on other forwarding information."
::= { rbridgeMultiFibEntry 2 }
Rijhsinghani & Zebrose Standards Track [Page 28]
RFC 6850 RBridges: TRILL Base MIB January 2013
-- ---------------------------------------------------------- --
-- The RBridge VLAN Table
-- ---------------------------------------------------------- --
rbridgeVlanTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeVlanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about VLANs on the
RBridge."
::= { rbridgeVlan 1 }
rbridgeVlanEntry OBJECT-TYPE
SYNTAX RbridgeVlanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information about VLANs on the RBridge."
INDEX { rbridgeVlanIndex }
::= { rbridgeVlanTable 1 }
RbridgeVlanEntry ::=
SEQUENCE {
rbridgeVlanIndex
Unsigned32,
rbridgeVlanForwarderLosts
Counter32,
rbridgeVlanDisableLearning
TruthValue,
rbridgeVlanSnooping
INTEGER
}
rbridgeVlanIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4094|4096..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VLAN-ID referring to this VLAN."
::= { rbridgeVlanEntry 1 }
rbridgeVlanForwarderLosts OBJECT-TYPE
SYNTAX Counter32
UNITS "times"
MAX-ACCESS read-only
STATUS current
Rijhsinghani & Zebrose Standards Track [Page 29]
RFC 6850 RBridges: TRILL Base MIB January 2013
DESCRIPTION
"The number of times this RBridge has lost appointed
forwarder status for this VLAN on any of its ports.
Discontinuities in the value of this counter can occur
at re-initialization of the management system."
REFERENCE
"RFC 6325, Section 4.8.3"
::= { rbridgeVlanEntry 2 }
rbridgeVlanDisableLearning OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Disable learning of MAC addresses seen in this VLAN.
One application of this may be to restrict learning to
ESADI. To disable learning, the value of this object
should be set to 'true'. The default is 'false'.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.8"
DEFVAL { false }
::= { rbridgeVlanEntry 3 }
rbridgeVlanSnooping OBJECT-TYPE
SYNTAX INTEGER {
notSupported(1),
ipv4(2),
ipv6(3),
ipv4v6(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"IP Multicast Snooping on this VLAN. For RBridges
performing both IPv4 and IPv6 IP Multicast Snooping, the
value returned is ipv4v6(4)."
REFERENCE
"RFC 6325, Section 4.7"
::= { rbridgeVlanEntry 4 }
Rijhsinghani & Zebrose Standards Track [Page 30]
RFC 6850 RBridges: TRILL Base MIB January 2013
-- ---------------------------------------------------------- --
-- The RBridge VLAN Port Table
-- ---------------------------------------------------------- --
rbridgeVlanPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeVlanPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about VLANs on an RBridge
port."
::= { rbridgeVlan 2 }
rbridgeVlanPortEntry OBJECT-TYPE
SYNTAX RbridgeVlanPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information about VLANs on the RBridge port."
INDEX { rbridgeBasePort, rbridgeVlanIndex }
::= { rbridgeVlanPortTable 1 }
RbridgeVlanPortEntry ::=
SEQUENCE {
rbridgeVlanPortInhibited
TruthValue,
rbridgeVlanPortForwarder
TruthValue,
rbridgeVlanPortAnnouncing
TruthValue,
rbridgeVlanPortDetectedVlanMapping
TruthValue
}
rbridgeVlanPortInhibited OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This VLAN has been inhibited by the RBridge due to
conflicting forwarder information received from another
RBridge, when the value of this object is 'true'."
REFERENCE
"RFC 6325, Section 4.2.4.3"
::= { rbridgeVlanPortEntry 1 }
rbridgeVlanPortForwarder OBJECT-TYPE
SYNTAX TruthValue
Rijhsinghani & Zebrose Standards Track [Page 31]
RFC 6850 RBridges: TRILL Base MIB January 2013
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This RBridge is an appointed forwarder for this VLAN
on this port, when the value of this object is 'true'."
REFERENCE
"RFC 6325, Section 4.2.4.3"
::= { rbridgeVlanPortEntry 2 }
rbridgeVlanPortAnnouncing OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"TRILL-Hellos tagged with this VLAN can be sent by this
RBridge on this port, when the value of this object
is 'true'.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.4.3"
DEFVAL { true }
::= { rbridgeVlanPortEntry 3 }
rbridgeVlanPortDetectedVlanMapping OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"VLAN mapping has been detected on the link attached
to this port, when the value of this object is 'true'."
REFERENCE
"RFC 6325, Section 4.4.5"
::= { rbridgeVlanPortEntry 4 }
-- ---------------------------------------------------------- --
-- The RBridge Port Counter Table
--
-- These counters supplement counters in the Bridge MIB.
--
-- For example, total frames received by a bridge port and total
-- frames transmitted by a bridge port are reported in the
-- Port In Frames and Port Out Frames counters of the Bridge MIB.
-- These total bridge frame counters include native as well as
-- encapsulated frames.
--
Rijhsinghani & Zebrose Standards Track [Page 32]
RFC 6850 RBridges: TRILL Base MIB January 2013
-- As another example, frames discarded due to excessive frame
-- size are reported in the port counter MTU Exceeded Discards
-- in the Bridge MIB.
-- ---------------------------------------------------------- --
rbridgePortCounterTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgePortCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains per-port counters for this RBridge."
::= { rbridgeCounter 1 }
rbridgePortCounterEntry OBJECT-TYPE
SYNTAX RbridgePortCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Counters for a port on this RBridge."
INDEX { rbridgeBasePort }
::= { rbridgePortCounterTable 1 }
RbridgePortCounterEntry ::=
SEQUENCE {
rbridgePortRpfCheckFails
Counter32,
rbridgePortHopCountExceeds
Counter32,
rbridgePortOptionDrops
Counter32,
rbridgePortTrillInFrames
Counter64,
rbridgePortTrillOutFrames
Counter64
}
rbridgePortRpfCheckFails OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a multi-destination frame was
dropped on this port because the Reverse Path Forwarding
(RPF) check failed.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
Rijhsinghani & Zebrose Standards Track [Page 33]
RFC 6850 RBridges: TRILL Base MIB January 2013
other times as indicated by the value of the
ifCounterDiscontinuityTime object of the associated
interface."
REFERENCE
"RFC 6325, Section 4.5.2"
::= { rbridgePortCounterEntry 1 }
rbridgePortHopCountExceeds OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a frame was dropped on this port
because its hop count was zero.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of the
ifCounterDiscontinuityTime object of the associated
interface."
REFERENCE
"RFC 6325, Section 3.6"
::= { rbridgePortCounterEntry 2 }
rbridgePortOptionDrops OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a frame was dropped on this port
because it contained unsupported options.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of the
ifCounterDiscontinuityTime object of the associated
interface."
REFERENCE
"RFC 6325, Section 3.5"
::= { rbridgePortCounterEntry 3 }
rbridgePortTrillInFrames OBJECT-TYPE
SYNTAX Counter64
UNITS "frames"
MAX-ACCESS read-only
STATUS current
Rijhsinghani & Zebrose Standards Track [Page 34]
RFC 6850 RBridges: TRILL Base MIB January 2013
DESCRIPTION
"The number of TRILL-encapsulated frames that have been
received by this port from its attached link, including
management frames.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of the
ifCounterDiscontinuityTime object of the associated
interface."
REFERENCE
"RFC 6325, Section 2.3"
::= { rbridgePortCounterEntry 4 }
rbridgePortTrillOutFrames OBJECT-TYPE
SYNTAX Counter64
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of TRILL-encapsulated frames that have been
transmitted by this port to its attached link, including
management frames.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of the
ifCounterDiscontinuityTime object of the associated
interface."
REFERENCE
"RFC 6325, Section 2.3"
::= { rbridgePortCounterEntry 5 }
-- ---------------------------------------------------------- --
-- The RBridge VLAN ESADI Table
-- ---------------------------------------------------------- --
rbridgeEsadiTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeEsadiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains information about ESADI instances on
VLANs, if available."
REFERENCE
"RFC 6325, Section 4.2.5"
::= { rbridgeEsadi 1 }
Rijhsinghani & Zebrose Standards Track [Page 35]
RFC 6850 RBridges: TRILL Base MIB January 2013
rbridgeEsadiEntry OBJECT-TYPE
SYNTAX RbridgeEsadiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about an ESADI instance on a VLAN."
INDEX { rbridgeVlanIndex }
::= { rbridgeEsadiTable 1 }
RbridgeEsadiEntry ::=
SEQUENCE {
rbridgeEsadiEnable
TruthValue,
rbridgeEsadiConfidence
Unsigned32,
rbridgeEsadiDrbPriority
Unsigned32,
rbridgeEsadiDrb
RbridgeAddress,
rbridgeEsadiDrbHoldingTime
Unsigned32,
rbridgeEsadiRowStatus
RowStatus
}
rbridgeEsadiEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the RBridge is participating in an ESADI instance for
this VLAN, the value of this object is 'true'. To disable
participation, set it to 'false'.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.2.5"
DEFVAL { true }
::= { rbridgeEsadiEntry 1 }
rbridgeEsadiConfidence OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Confidence level of address entries sent by this
ESADI instance. The default is 16.
Rijhsinghani & Zebrose Standards Track [Page 36]
RFC 6850 RBridges: TRILL Base MIB January 2013
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.2.5"
DEFVAL { 16 }
::= { rbridgeEsadiEntry 2 }
rbridgeEsadiDrbPriority OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The priority of this RBridge for being selected as the
DRB for this ESADI instance.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.2.5"
::= { rbridgeEsadiEntry 3 }
rbridgeEsadiDrb OBJECT-TYPE
SYNTAX RbridgeAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The DRB on this ESADI instance's virtual link."
REFERENCE
"RFC 6325, Section 4.2.5"
::= { rbridgeEsadiEntry 4 }
rbridgeEsadiDrbHoldingTime OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The holding time for this ESADI instance.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.2.5"
::= { rbridgeEsadiEntry 5 }
rbridgeEsadiRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
Rijhsinghani & Zebrose Standards Track [Page 37]
RFC 6850 RBridges: TRILL Base MIB January 2013
DESCRIPTION
"This object indicates the status of the entry."
::= { rbridgeEsadiEntry 6 }
-- ---------------------------------------------------------- --
-- The RBridge IP Multicast Snooping Port Table
-- ---------------------------------------------------------- --
rbridgeSnoopingPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeSnoopingPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"For RBridges implementing IP Multicast Snooping,
information about ports on which the presence of IPv4
or IPv6 multicast routers has been detected."
REFERENCE
"RFC 6325, Section 4.7"
::= { rbridgeSnooping 1 }
rbridgeSnoopingPortEntry OBJECT-TYPE
SYNTAX RbridgeSnoopingPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about ports on which the presence of IPv4
or IPv6 multicast routers has been detected for a
VLAN."
INDEX { rbridgeBasePort, rbridgeVlanIndex }
::= { rbridgeSnoopingPortTable 1 }
RbridgeSnoopingPortEntry ::=
SEQUENCE {
rbridgeSnoopingPortAddrType
INTEGER
}
rbridgeSnoopingPortAddrType OBJECT-TYPE
SYNTAX INTEGER {
ipv4(1),
ipv6(2),
ipv4v6(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address type of an IP multicast router detected
Rijhsinghani & Zebrose Standards Track [Page 38]
RFC 6850 RBridges: TRILL Base MIB January 2013
on this port and VLAN. If only IPv4 router(s)
are detected, the value returned is 'ipv4'. If only
IPv6 routers are detected, the value returned is
'ipv6'. If both IPv4 and IPv6 routers are detected on
this port and VLAN, the value returned is 'ipv4v6'."
REFERENCE
"RFC 6325, Section 4.7"
::= { rbridgeSnoopingPortEntry 1 }
-- ---------------------------------------------------------- --
-- The RBridge IP Multicast Snooping Address Table
-- ---------------------------------------------------------- --
rbridgeSnoopingAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeSnoopingAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"For RBridges implementing IP Multicast Snooping,
information about IP multicast addresses being
snooped."
REFERENCE
"RFC 6325, Section 4.8"
::= { rbridgeSnooping 2 }
rbridgeSnoopingAddrEntry OBJECT-TYPE
SYNTAX RbridgeSnoopingAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about IP multicast addresses being
snooped."
INDEX { rbridgeVlanIndex, rbridgeSnoopingAddrType,
rbridgeSnoopingAddr }
::= { rbridgeSnoopingAddrTable 1 }
RbridgeSnoopingAddrEntry ::=
SEQUENCE {
rbridgeSnoopingAddrType
InetAddressType,
rbridgeSnoopingAddr
InetAddress,
rbridgeSnoopingAddrPorts
PortList
}
rbridgeSnoopingAddrType OBJECT-TYPE
SYNTAX InetAddressType
Rijhsinghani & Zebrose Standards Track [Page 39]
RFC 6850 RBridges: TRILL Base MIB January 2013
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP multicast address type for which a listener has been
detected by this RBridge. This MIB requires support for only
IPv4 and IPv6 address types."
REFERENCE
"RFC 6325, Section 4.7"
::= { rbridgeSnoopingAddrEntry 1 }
rbridgeSnoopingAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP multicast address for which a listener has been
detected by this RBridge. The address type of this object
is specified in rbridgeSnoopingAddrType. This MIB requires
support for only global IPv4 and IPv6 addresses, so the
length of the object can be either 4 or 16 bytes. Hence,
the index will not exceed the OID size limit."
REFERENCE
"RFC 6325, Section 4.7"
::= { rbridgeSnoopingAddrEntry 2 }
rbridgeSnoopingAddrPorts OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The set of ports on which a listener has been detected
for this IP multicast address."
REFERENCE
"RFC 6325, Section 4.7"
::= { rbridgeSnoopingAddrEntry 3 }
-- ---------------------------------------------------------- --
-- Distribution Trees
-- ---------------------------------------------------------- --
rbridgeDtreePriority OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The distribution tree root priority for this RBridge.
Rijhsinghani & Zebrose Standards Track [Page 40]
RFC 6850 RBridges: TRILL Base MIB January 2013
The default value of this object is 32768.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.5"
::= { rbridgeDtree 1 }
rbridgeDtreeActiveTrees OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of trees being computed by all RBridges
in the campus."
REFERENCE
"RFC 6325, Section 4.5"
::= { rbridgeDtree 2 }
rbridgeDtreeMaxTrees OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of trees this RBridge can compute."
REFERENCE
"RFC 6325, Section 4.5"
::= { rbridgeDtree 3 }
rbridgeDtreeDesiredUseTrees OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of trees this RBridge would like to
use for transmission of ingress multi-destination frames."
REFERENCE
"RFC 6325, Section 4.5"
::= { rbridgeDtree 4 }
rbridgeDtreeTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeDtreeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about distribution trees being computed
by this RBridge."
Rijhsinghani & Zebrose Standards Track [Page 41]
RFC 6850 RBridges: TRILL Base MIB January 2013
REFERENCE
"RFC 6325, Section 4.5"
::= { rbridgeDtree 5 }
rbridgeDtreeEntry OBJECT-TYPE
SYNTAX RbridgeDtreeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"List of information about distribution trees being computed
by this RBridge."
INDEX { rbridgeDtreeNumber }
::= { rbridgeDtreeTable 1 }
RbridgeDtreeEntry ::=
SEQUENCE {
rbridgeDtreeNumber
Unsigned32,
rbridgeDtreeNickname
RbridgeNickname,
rbridgeDtreeIngress
TruthValue
}
rbridgeDtreeNumber OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The tree number of a distribution tree being computed by
this RBridge."
REFERENCE
"RFC 6325, Section 4.5"
::= { rbridgeDtreeEntry 1 }
rbridgeDtreeNickname OBJECT-TYPE
SYNTAX RbridgeNickname
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The nickname of the distribution tree."
REFERENCE
"RFC 6325, Section 4.5"
::= { rbridgeDtreeEntry 2 }
rbridgeDtreeIngress OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
Rijhsinghani & Zebrose Standards Track [Page 42]
RFC 6850 RBridges: TRILL Base MIB January 2013
STATUS current
DESCRIPTION
"Indicates whether this RBridge might choose this
distribution tree to ingress a multi-destination frame."
REFERENCE
"RFC 6325, Section 4.5"
::= { rbridgeDtreeEntry 3 }
-- ---------------------------------------------------------- --
-- TRILL Neighbor List
-- ---------------------------------------------------------- --
rbridgeTrillMinMtuDesired OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired minimum acceptable inter-RBridge link MTU for
the campus, that is, originatingLSPBufferSize.
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.3"
::= { rbridgeTrill 1 }
rbridgeTrillSz OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum acceptable inter-RBridge link size for the
campus for the proper operation of TRILL IS-IS."
REFERENCE
"RFC 6325, Section 4.3"
::= { rbridgeTrill 2 }
rbridgeTrillMaxMtuProbes OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of failed MTU-probes before the RBridge
concludes that a particular MTU is not supported by
a neighbor.
Rijhsinghani & Zebrose Standards Track [Page 43]
RFC 6850 RBridges: TRILL Base MIB January 2013
The value of this object MUST be retained across
re-initializations of the management system."
REFERENCE
"RFC 6325, Section 4.3"
::= { rbridgeTrill 3 }
rbridgeTrillNbrTable OBJECT-TYPE
SYNTAX SEQUENCE OF RbridgeTrillNbrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about this RBridge's TRILL neighbors."
REFERENCE
"RFC 6325, Section 4.4.2.1"
::= { rbridgeTrill 4 }
rbridgeTrillNbrEntry OBJECT-TYPE
SYNTAX RbridgeTrillNbrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"List of information about this RBridge's TRILL neighbors."
INDEX { rbridgeTrillNbrMacAddr }
::= { rbridgeTrillNbrTable 1 }
RbridgeTrillNbrEntry ::=
SEQUENCE {
rbridgeTrillNbrMacAddr
MacAddress,
rbridgeTrillNbrMtu
Unsigned32,
rbridgeTrillNbrFailedMtuTest
TruthValue
}
rbridgeTrillNbrMacAddr OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The MAC address of a neighbor of this RBridge."
REFERENCE
"RFC 6325, Section 4.4.2.1"
::= { rbridgeTrillNbrEntry 1 }
rbridgeTrillNbrMtu OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
Rijhsinghani & Zebrose Standards Track [Page 44]
RFC 6850 RBridges: TRILL Base MIB January 2013
STATUS current
DESCRIPTION
"MTU size for this neighbor for IS-IS communication
purposes."
REFERENCE
"RFC 6325, Section 4.3.2"
::= { rbridgeTrillNbrEntry 2 }
rbridgeTrillNbrFailedMtuTest OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, indicates that the neighbor's tested MTU is less
than the minimum acceptable inter-bridge link MTU for the
campus (1470)."
REFERENCE
"RFC 6325, Section 4.3.1"
::= { rbridgeTrillNbrEntry 3 }
-- ---------------------------------------------------------- --
-- Notifications for use by RBridges
-- ---------------------------------------------------------- --
rbridgeBaseNewDrb NOTIFICATION-TYPE
-- OBJECTS { }
STATUS current
DESCRIPTION
"The rbridgeBaseNewDrb notification indicates that the
sending agent has become the new Designated RBridge; the
notification is sent by an RBridge soon after its election
as the new DRB root, e.g., upon expiration of the Topology
Change Timer, immediately subsequent to its election."
::= { rbridgeNotifications 1 }
rbridgeBaseTopologyChange NOTIFICATION-TYPE
-- OBJECTS { }
STATUS current
DESCRIPTION
"The rbridgeBaseTopologyChange notification is sent by an
RBridge when any of its configured ports transition to/from
the VLAN-x designated forwarder. The notification is not
sent if an rbridgeBaseNewDrb notification is sent for the
same transition."
::= { rbridgeNotifications 2 }
Rijhsinghani & Zebrose Standards Track [Page 45]
RFC 6850 RBridges: TRILL Base MIB January 2013
-- Compliance and Group sections
rbridgeCompliances OBJECT IDENTIFIER ::= { rbridgeConformance 1 }
rbridgeGroup OBJECT IDENTIFIER ::= { rbridgeConformance 2 }
-- ---------------------------------------------------------- --
-- Units of Conformance
-- ---------------------------------------------------------- --
rbridgeBaseGroup OBJECT-GROUP
OBJECTS {
rbridgeBaseTrillVersion,
rbridgeBaseNumPorts,
rbridgeBaseForwardDelay,
rbridgeBaseUniMultipathEnable,
rbridgeBaseMultiMultipathEnable,
rbridgeBaseAcceptEncapNonadj,
rbridgeBaseNicknameNumber
}
STATUS current
DESCRIPTION
"A collection of objects providing basic control
and status information for the RBridge."
::= { rbridgeGroup 1 }
rbridgeBaseNicknameGroup OBJECT-GROUP
OBJECTS {
rbridgeBaseNicknamePriority,
rbridgeBaseNicknameDtrPriority,
rbridgeBaseNicknameType,
rbridgeBaseNicknameRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing basic control
and status information for RBridge nicknames."
::= { rbridgeGroup 2 }
rbridgeBasePortGroup OBJECT-GROUP
OBJECTS {
rbridgeBasePortIfIndex,
rbridgeBasePortDisable,
rbridgeBasePortTrunkPort,
rbridgeBasePortAccessPort,
rbridgeBasePortP2pHellos,
rbridgeBasePortState,
Rijhsinghani & Zebrose Standards Track [Page 46]
RFC 6850 RBridges: TRILL Base MIB January 2013
rbridgeBasePortDesiredDesigVlan,
rbridgeBasePortDesigVlan,
rbridgeBasePortInhibitionTime,
rbridgeBasePortDisableLearning,
rbridgeBasePortStpRoot,
rbridgeBasePortStpRootChanges,
rbridgeBasePortStpWiringCloset
}
STATUS current
DESCRIPTION
"A collection of objects providing basic control
and status information for RBridge ports."
::= { rbridgeGroup 3 }
rbridgeFdbGroup OBJECT-GROUP
OBJECTS {
rbridgeConfidenceNative,
rbridgeConfidenceDecap,
rbridgeConfidenceStatic,
rbridgeUniFdbPort,
rbridgeUniFdbNickname,
rbridgeUniFdbConfidence,
rbridgeUniFdbStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing information
about the Unicast Address Database."
::= { rbridgeGroup 4 }
rbridgeFibGroup OBJECT-GROUP
OBJECTS {
rbridgeUniFibHopCount,
rbridgeMultiFibPorts
}
STATUS current
DESCRIPTION
"A collection of objects providing information
about the Unicast and Multicast FIBs."
::= { rbridgeGroup 5 }
rbridgeVlanGroup OBJECT-GROUP
OBJECTS {
rbridgeVlanForwarderLosts,
rbridgeVlanDisableLearning,
rbridgeVlanSnooping,
rbridgeVlanPortInhibited,
rbridgeVlanPortForwarder,
Rijhsinghani & Zebrose Standards Track [Page 47]
RFC 6850 RBridges: TRILL Base MIB January 2013
rbridgeVlanPortAnnouncing,
rbridgeVlanPortDetectedVlanMapping
}
STATUS current
DESCRIPTION
"A collection of objects providing information
about VLANs on the RBridge."
::= { rbridgeGroup 6 }
rbridgePortCounterGroup OBJECT-GROUP
OBJECTS {
rbridgePortRpfCheckFails,
rbridgePortHopCountExceeds,
rbridgePortOptionDrops,
rbridgePortTrillInFrames,
rbridgePortTrillOutFrames
}
STATUS current
DESCRIPTION
"A collection of objects providing per-port
counters for the RBridge."
::= { rbridgeGroup 7 }
rbridgeEsadiGroup OBJECT-GROUP
OBJECTS {
rbridgeEsadiEnable,
rbridgeEsadiConfidence,
rbridgeEsadiDrbPriority,
rbridgeEsadiDrb,
rbridgeEsadiDrbHoldingTime,
rbridgeEsadiRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing information
about ESADI instances on the RBridge."
::= { rbridgeGroup 8 }
rbridgeSnoopingGroup OBJECT-GROUP
OBJECTS {
rbridgeSnoopingPortAddrType,
rbridgeSnoopingAddrPorts
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
IP Multicast Snooping. This MIB requires support for
only global IPv4 and IPv6 address types in
Rijhsinghani & Zebrose Standards Track [Page 48]
RFC 6850 RBridges: TRILL Base MIB January 2013
rbridgeSnoopingPortAddrType and rbridgeSnoopingAddrType,
so the length of rbridgeSnoopingAddr can be either 4 or
16 bytes."
::= { rbridgeGroup 9 }
rbridgeDtreeGroup OBJECT-GROUP
OBJECTS {
rbridgeDtreePriority,
rbridgeDtreeActiveTrees,
rbridgeDtreeMaxTrees,
rbridgeDtreeDesiredUseTrees,
rbridgeDtreeNickname,
rbridgeDtreeIngress
}
STATUS current
DESCRIPTION
"A collection of objects providing information
about distribution trees."
::= { rbridgeGroup 10 }
rbridgeTrillGroup OBJECT-GROUP
OBJECTS {
rbridgeTrillMinMtuDesired,
rbridgeTrillSz,
rbridgeTrillMaxMtuProbes,
rbridgeTrillNbrMtu,
rbridgeTrillNbrFailedMtuTest
}
STATUS current
DESCRIPTION
"A collection of objects providing information
about TRILL neighbors."
::= { rbridgeGroup 11 }
rbridgeNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
rbridgeBaseNewDrb,
rbridgeBaseTopologyChange
}
STATUS current
DESCRIPTION
"A collection of objects describing notifications (traps)."
::= { rbridgeGroup 12 }
Rijhsinghani & Zebrose Standards Track [Page 49]
RFC 6850 RBridges: TRILL Base MIB January 2013
-- ---------------------------------------------------------- --
-- Compliance Statement
-- ---------------------------------------------------------- --
rbridgeCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for support of RBridge
services."
MODULE
MANDATORY-GROUPS {
rbridgeBaseGroup,
rbridgeBaseNicknameGroup,
rbridgeBasePortGroup,
rbridgeFdbGroup,
rbridgeFibGroup,
rbridgeVlanGroup,
rbridgeDtreeGroup,
rbridgeTrillGroup,
rbridgeNotificationGroup
}
GROUP rbridgePortCounterGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP rbridgeEsadiGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP rbridgeSnoopingGroup
DESCRIPTION
"Implementation of this group is optional."
::= { rbridgeCompliances 1 }
rbridgeReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"When this MIB is implemented in read-only mode, then
the implementation can claim read-only compliance.
In that case, RBridge objects can be monitored but
cannot be configured with this implementation."
Rijhsinghani & Zebrose Standards Track [Page 50]
RFC 6850 RBridges: TRILL Base MIB January 2013
MODULE
MANDATORY-GROUPS {
rbridgeBaseGroup,
rbridgeBaseNicknameGroup,
rbridgeBasePortGroup,
rbridgeFdbGroup,
rbridgeFibGroup,
rbridgeVlanGroup,
rbridgeDtreeGroup,
rbridgeTrillGroup,
rbridgeNotificationGroup
}
OBJECT rbridgeBaseForwardDelay
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBaseUniMultipathEnable
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBaseMultiMultipathEnable
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBaseAcceptEncapNonadj
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBaseNicknameNumber
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBaseNicknamePriority
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBaseNicknameDtrPriority
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Rijhsinghani & Zebrose Standards Track [Page 51]
RFC 6850 RBridges: TRILL Base MIB January 2013
OBJECT rbridgeBaseNicknameRowStatus
SYNTAX INTEGER { active(1) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and 'active' is the only
status that needs to be supported."
OBJECT rbridgeBasePortDisable
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBasePortTrunkPort
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBasePortAccessPort
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBasePortP2pHellos
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBasePortInhibitionTime
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBasePortDisableLearning
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBasePortDesiredDesigVlan
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeBasePortStpWiringCloset
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Rijhsinghani & Zebrose Standards Track [Page 52]
RFC 6850 RBridges: TRILL Base MIB January 2013
OBJECT rbridgeConfidenceNative
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeConfidenceDecap
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeConfidenceStatic
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeVlanDisableLearning
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeVlanPortAnnouncing
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeEsadiEnable
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeEsadiConfidence
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeEsadiDrbPriority
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeEsadiDrbHoldingTime
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeEsadiRowStatus
SYNTAX INTEGER { active(1) }
MIN-ACCESS read-only
Rijhsinghani & Zebrose Standards Track [Page 53]
RFC 6850 RBridges: TRILL Base MIB January 2013
DESCRIPTION
"Write access is not required, and 'active' is the only
status that needs to be supported."
OBJECT rbridgeDtreePriority
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeTrillMinMtuDesired
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT rbridgeTrillMaxMtuProbes
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
GROUP rbridgePortCounterGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP rbridgeEsadiGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP rbridgeSnoopingGroup
DESCRIPTION
"Implementation of this group is optional."
::= { rbridgeCompliances 2 }
END
Rijhsinghani & Zebrose Standards Track [Page 54]
RFC 6850 RBridges: TRILL Base MIB January 2013
8. Security Considerations
This MIB relates to a system that will provide network connectivity
and packet-forwarding services. As such, improper manipulation of
the objects represented by this MIB may result in denial of service
to a large number of end-users.
There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
The following tables and objects in the RBRIDGE-MIB can be
manipulated to interfere with the operation of RBridges:
o rbridgeBaseUniMultipathEnable affects the ability of the RBridge
to route unicast traffic over multiple paths, and
rbridgeBaseMultiMultipathEnable affects the ability of the RBridge
to route multi-destination traffic over multiple paths.
o rbridgeBasePortTable contains a number of objects that may affect
network connectivity. Actions that may be triggered by
manipulating objects in this table include disabling of an RBridge
port, discarding of native packets, disabling learning, and
others.
o rbridgeEsadiTable contains objects that affect the operation of
the ESADI protocol used for learning, and manipulation of the
objects contained therein can be used to confuse the learning
ability of RBridges.
o rbridgeDtreePriority can affect computation of distribution trees
within an RBridge campus, thereby affecting the forwarding of
multi-destination traffic.
o rbridgeTrillMinMtuDesired can affect the size of packets being
used to exchange information between RBridges.
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
Rijhsinghani & Zebrose Standards Track [Page 55]
RFC 6850 RBridges: TRILL Base MIB January 2013
the network via SNMP. For example, access to network topology and
RBridge attributes can reveal information that should not be
available to all users of the network.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
there is no control as to who on the secure network is allowed to
access and GET/SET (read/change/create/delete) the objects in this
MIB module.
Implementations SHOULD provide the security features described by the
SNMPv3 framework (see [RFC3410]), and implementations claiming
compliance to the SNMPv3 standard MUST include full support for
authentication and privacy via the User-based Security Model (USM)
[RFC3414] with the AES cipher algorithm [RFC3826]. Implementations
MAY also provide support for the Transport Security Model (TSM)
[RFC5591] in combination with a secure transport such as SSH
[RFC5592] or TLS/DTLS [RFC6353].
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
For other RBridge security considerations, see [RFC6325].
9. IANA Considerations
The MIB module in this document uses the following IANA-assigned
OBJECT IDENTIFIER value recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
rbridgeMIB { mib-2 214 }
10. Contributors
The authors would like to acknowledge the contributions of Donald
Eastlake, Radia Perlman, Anoop Ghanwani, Dan Romascanu, Mahesh Akula,
Sue Hares, and Joan Cucchiara.
Rijhsinghani & Zebrose Standards Track [Page 56]
RFC 6850 RBridges: TRILL Base MIB January 2013
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2",
STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Conformance Statements for SMIv2",
STD 58, RFC 2580, April 1999.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", STD 62, RFC 3414, December 2002.
[RFC3826] Blumenthal, U., Maino, F., and K. McCloghrie, "The
Advanced Encryption Standard (AES) Cipher Algorithm in
the SNMP User-based Security Model", RFC 3826, June 2004.
[RFC4001] Daniele, M., Haberman, B., Routhier, S., and J.
Schoenwaelder, "Textual Conventions for Internet Network
Addresses", RFC 4001, February 2005.
[RFC4188] Norseth, K., Ed., and E. Bell, Ed., "Definitions of
Managed Objects for Bridges", RFC 4188, September 2005.
[RFC4363] Levi, D. and D. Harrington, "Definitions of Managed
Objects for Bridges with Traffic Classes, Multicast
Filtering, and Virtual LAN Extensions", RFC 4363,
January 2006.
[RFC4444] Parker, J., Ed., "Management Information Base for
Intermediate System to Intermediate System (IS-IS)",
RFC 4444, April 2006.
Rijhsinghani & Zebrose Standards Track [Page 57]
RFC 6850 RBridges: TRILL Base MIB January 2013
[RFC5591] Harrington, D. and W. Hardaker, "Transport Security Model
for the Simple Network Management Protocol (SNMP)",
RFC 5591, June 2009.
[RFC5592] Harrington, D., Salowey, J., and W. Hardaker, "Secure
Shell Transport Model for the Simple Network Management
Protocol (SNMP)", RFC 5592, June 2009.
[RFC6325] Perlman, R., Eastlake 3rd, D., Dutt, D., Gai, S., and A.
Ghanwani, "Routing Bridges (RBridges): Base Protocol
Specification", RFC 6325, July 2011.
[RFC6353] Hardaker, W., "Transport Layer Security (TLS) Transport
Model for the Simple Network Management Protocol (SNMP)",
RFC 6353, July 2011.
11.2. Informative References
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
[RFC4663] Harrington, D., "Transferring MIB Work from IETF Bridge
MIB WG to IEEE 802.1 WG", RFC 4663, September 2006.
[RFC5556] Touch, J. and R. Perlman, "Transparent Interconnection of
Lots of Links (TRILL): Problem and Applicability
Statement", RFC 5556, May 2009.
Rijhsinghani & Zebrose Standards Track [Page 58]
RFC 6850 RBridges: TRILL Base MIB January 2013
Authors' Addresses
Anil Rijhsinghani
Hewlett-Packard
153 Taylor St.
Littleton, MA
USA
Phone: +1 508 323 1251
EMail: anil@charter.net
Kate Zebrose
HW Embedded
26 Josephine Ave.
Somerville, MA
USA
Phone: +1 617 840 9673
EMail: zebrose@alum.mit.edu
Rijhsinghani & Zebrose Standards Track [Page 59]