💾 Archived View for perso.pw › blog › articles › mlvpn.gmi captured on 2023-09-28 at 16:37:53. Gemini links have been rewritten to link to archived content
⬅️ Previous capture (2023-05-24)
-=-=-=-=-=-=-
In this article I'll explain how to aggregate internet access bandwidth using
how-to.
with variable bandwidth or packet loss.
access and on the client on which you want to aggregate the links, this is like
doing multiples VPN to the same remote server with a VPN per link, and
aggregate them.
Multi-wan roundrobin / load balancer doesn't allow to stack bandwidth but
doesn't require a remote server, depend on what you want to do, this may be
enough and mlvpn may not be required.
between two OpenBSD hosts, your setup may differ.
Here is a simple network, the client has access to 2 ISP through two ethernet
interfaces.
em0 and em1 will have to be on different rdomains (it's a feature to separate
routing tables).
Let's say the public ip of the server is 1.2.3.4.
[internet]
↑
| (public ip on em0)
#-------------#
| |
| Server |
| |
#-------------#
| |
| |
| |
| |
(internet) | | (internet)
#-------------# #-------------#
| | | |
| ISP 1 | | ISP 2 |
| | | | (you certainly don't control those)
#-------------# #-------------#
| |
| |
(dsl1 via em0)| | (dsl1 via em1)
#-------------#
| |
| Client |
| |
#-------------#
As said previously, em0 and em1 must be on different rdomains, it can easily be
done by adding `rdomain 1` and `rdomain 2` to the interfaces configuration.
Example in **/etc/hostname.em0**
rdomain 1
dhcp
On OpenBSD the installation is as easy as `pkg_add mlvpn` (should work starting
from 6.7 because it required patching).
Once the network configuration is done on the client, there are 3 steps to do
to get aggregation working:
1. mlvpn configuration on the server
2. mlvpn configuration on the client
3. activating NAT on the client
On the server we will use the UDP ports 5080 et 5081.
Connections speed must be defined in bytes to allow **mlvpn** to correctly
balance the traffic over the links, this is really important.
The line `bandwidth_upload = 1468006` is the maximum **download bandwidth of the
client** on the specified link in bytes. If you have a download speed of 1.4 MB/s
then you can choose a value of 1.4\*1024\*1024 => 1468006.
The line `bandwidth_download = 102400` is the maximum **upload bandwidth of the
client** on the specified link in bytes. If you have an upload speed of 100 kB/s
then you can choose a value of 100*1024 => 102400.
The **password** line must be a very long random string, it's a shared secret
between the client and the server.
# config you don't need to change
[general]
statuscommand = "/etc/mlvpn/mlvpn_updown.sh"
protocol = "tcp"
loglevel = 4
mode = "server"
tuntap = "tun"
interface_name = "tun0"
cleartext_data = 0
ip4 = "10.44.43.2/30"
ip4_gateway = "10.44.43.1"
# things you need to change
password = "apoziecxjvpoxkvpzeoirjdskpoezroizepzdlpojfoiezjrzanzaoinzoi"
[dsl1]
bindhost = "1.2.3.4"
bindport = 5080
bandwidth_upload = 1468006
bandwidth_download = 102400
[dsl2]
bindhost = "1.2.3.4"
bindport = 5081
bandwidth_upload = 1468006
bandwidth_download = 102400
The `password` value must match the one on the server, the values of `ip4` and
`ip4_gateway` must be reversed compared to the server configuration (this is so
in the following example).
The `bindfib` lines must correspond to the according rdomain values of your
interfaces.
# config you don't need to change
[general]
statuscommand = "/etc/mlvpn/mlvpn_updown.sh"
loglevel = 4
mode = "client"
tuntap = "tun"
interface_name = "tun0"
ip4 = "10.44.43.1/30"
ip4_gateway = "10.44.43.2"
timeout = 30
cleartext_data = 0
password = "apoziecxjvpoxkvpzeoirjdskpoezroizepzdlpojfoiezjrzanzaoinzoi"
[dsl1]
remotehost = "1.2.3.4"
remoteport = 5080
bindfib = 1
[dsl2]
remotehost = "1.2.3.4"
remoteport = 5081
bindfib = 2
As with every VPN you must enable packet forwarding and create a pf rule for
the NAT.
Add this line in **/etc/sysctl.conf**:
net.inet.ip.forwarding=1
You can enable it now with `sysctl net.inet.ip.forwarding=1` instead of waiting
for a reboot.
In pf.conf you must allow the UDP ports 5080 and 5081 on the public interface
and enable nat, this can be done with the following lines in pf.conf but you
should obviously adapt to your configuration.
# allow NAT on VPN
pass in on tun0
pass out quick on em0 from 10.44.43.0/30 to any nat-to em0
# allow mlvpn to be reachable
pass in on egress inet proto udp from any to (egress) port 5080:5081
On both server and client you can run mlvpn with rcctl:
rcctl enable mlvpn
rcctl start mlvpn
You should see a new tun0 device on both systems and being able to ping them
through tun0.
Now, on the client **you have to add a default gateway through the mlvpn
tunnel** with the command ` route add -net default 10.44.43.2` (adapt if you
use others addresses). I still didn't find how to automatize it properly.
Your client should now use both WAN links and being visible with the remote
server public IP address.
si if you are comfortable with ipv6 it may be easy to set up IPv6 with the
variables `ip6` and `ip6_gateway` in mlvpn.conf.