💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc4648.txt captured on 2023-09-08 at 19:02:11.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group S. Josefsson
Request for Comments: 4648 SJD
Obsoletes: 3548 October 2006
Category: Standards Track
The Base16, Base32, and Base64 Data Encodings
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2006).
Abstract
This document describes the commonly used base 64, base 32, and base
16 encoding schemes. It also discusses the use of line-feeds in
encoded data, use of padding in encoded data, use of non-alphabet
characters in encoded data, use of different encoding alphabets, and
canonical encodings.
Josefsson Standards Track [Page 1]
RFC 4648 Base-N Encodings October 2006
Table of Contents
1. Introduction ....................................................3
2. Conventions Used in This Document ...............................3
3. Implementation Discrepancies ....................................3
3.1. Line Feeds in Encoded Data .................................3
3.2. Padding of Encoded Data ....................................4
3.3. Interpretation of Non-Alphabet Characters in Encoded Data ..4
3.4. Choosing the Alphabet ......................................4
3.5. Canonical Encoding .........................................5
4. Base 64 Encoding ................................................5
5. Base 64 Encoding with URL and Filename Safe Alphabet ............7
6. Base 32 Encoding ................................................8
7. Base 32 Encoding with Extended Hex Alphabet ....................10
8. Base 16 Encoding ...............................................10
9. Illustrations and Examples .....................................11
10. Test Vectors ..................................................12
11. ISO C99 Implementation of Base64 ..............................14
12. Security Considerations .......................................14
13. Changes Since RFC 3548 ........................................15
14. Acknowledgements ..............................................15
15. Copying Conditions ............................................15
16. References ....................................................16
16.1. Normative References .....................................16
16.2. Informative References ...................................16
Josefsson Standards Track [Page 2]
RFC 4648 Base-N Encodings October 2006
1. Introduction
Base encoding of data is used in many situations to store or transfer
data in environments that, perhaps for legacy reasons, are restricted
to US-ASCII [1] data. Base encoding can also be used in new
applications that do not have legacy restrictions, simply because it
makes it possible to manipulate objects with text editors.
In the past, different applications have had different requirements
and thus sometimes implemented base encodings in slightly different
ways. Today, protocol specifications sometimes use base encodings in
general, and "base64" in particular, without a precise description or
reference. Multipurpose Internet Mail Extensions (MIME) [4] is often
used as a reference for base64 without considering the consequences
for line-wrapping or non-alphabet characters. The purpose of this
specification is to establish common alphabet and encoding
considerations. This will hopefully reduce ambiguity in other
documents, leading to better interoperability.
2. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [2].
3. Implementation Discrepancies
Here we discuss the discrepancies between base encoding
implementations in the past and, where appropriate, mandate a
specific recommended behavior for the future.
3.1. Line Feeds in Encoded Data
MIME [4] is often used as a reference for base 64 encoding. However,
MIME does not define "base 64" per se, but rather a "base 64 Content-
Transfer-Encoding" for use within MIME. As such, MIME enforces a
limit on line length of base 64-encoded data to 76 characters. MIME
inherits the encoding from Privacy Enhanced Mail (PEM) [3], stating
that it is "virtually identical"; however, PEM uses a line length of
64 characters. The MIME and PEM limits are both due to limits within
SMTP.
Implementations MUST NOT add line feeds to base-encoded data unless
the specification referring to this document explicitly directs base
encoders to add line feeds after a specific number of characters.
Josefsson Standards Track [Page 3]
RFC 4648 Base-N Encodings October 2006
3.2. Padding of Encoded Data
In some circumstances, the use of padding ("=") in base-encoded data
is not required or used. In the general case, when assumptions about
the size of transported data cannot be made, padding is required to
yield correct decoded data.
Implementations MUST include appropriate pad characters at the end of
encoded data unless the specification referring to this document
explicitly states otherwise.
The base64 and base32 alphabets use padding, as described below in
sections 4 and 6, but the base16 alphabet does not need it; see
section 8.
3.3. Interpretation of Non-Alphabet Characters in Encoded Data
Base encodings use a specific, reduced alphabet to encode binary
data. Non-alphabet characters could exist within base-encoded data,
caused by data corruption or by design. Non-alphabet characters may
be exploited as a "covert channel", where non-protocol data can be
sent for nefarious purposes. Non-alphabet characters might also be
sent in order to exploit implementation errors leading to, e.g.,
buffer overflow attacks.
Implementations MUST reject the encoded data if it contains
characters outside the base alphabet when interpreting base-encoded
data, unless the specification referring to this document explicitly
states otherwise. Such specifications may instead state, as MIME
does, that characters outside the base encoding alphabet should
simply be ignored when interpreting data ("be liberal in what you
accept"). Note that this means that any adjacent carriage return/
line feed (CRLF) characters constitute "non-alphabet characters" and
are ignored. Furthermore, such specifications MAY ignore the pad
character, "=", treating it as non-alphabet data, if it is present
before the end of the encoded data. If more than the allowed number
of pad characters is found at the end of the string (e.g., a base 64
string terminated with "==="), the excess pad characters MAY also be
ignored.
3.4. Choosing the Alphabet
Different applications have different requirements on the characters
in the alphabet. Here are a few requirements that determine which
alphabet should be used:
Josefsson Standards Track [Page 4]
RFC 4648 Base-N Encodings October 2006
o Handled by humans. The characters "0" and "O" are easily
confused, as are "1", "l", and "I". In the base32 alphabet below,
where 0 (zero) and 1 (one) are not present, a decoder may
interpret 0 as O, and 1 as I or L depending on case. (However, by
default it should not; see previous section.)
o Encoded into structures that mandate other requirements. For base
16 and base 32, this determines the use of upper- or lowercase
alphabets. For base 64, the non-alphanumeric characters (in
particular, "/") may be problematic in file names and URLs.
o Used as identifiers. Certain characters, notably "+" and "/" in
the base 64 alphabet, are treated as word-breaks by legacy text
search/index tools.
There is no universally accepted alphabet that fulfills all the
requirements. For an example of a highly specialized variant, see
IMAP [8]. In this document, we document and name some currently used
alphabets.
3.5. Canonical Encoding
The padding step in base 64 and base 32 encoding can, if improperly
implemented, lead to non-significant alterations of the encoded data.
For example, if the input is only one octet for a base 64 encoding,
then all six bits of the first symbol are used, but only the first
two bits of the next symbol are used. These pad bits MUST be set to
zero by conforming encoders, which is described in the descriptions
on padding below. If this property do not hold, there is no
canonical representation of base-encoded data, and multiple base-
encoded strings can be decoded to the same binary data. If this
property (and others discussed in this document) holds, a canonical
encoding is guaranteed.
In some environments, the alteration is critical and therefore
decoders MAY chose to reject an encoding if the pad bits have not
been set to zero. The specification referring to this may mandate a
specific behaviour.
4. Base 64 Encoding
The following description of base 64 is derived from [3], [4], [5],
and [6]. This encoding may be referred to as "base64".
The Base 64 encoding is designed to represent arbitrary sequences of
octets in a form that allows the use of both upper- and lowercase
letters but that need not be human readable.
Josefsson Standards Track [Page 5]
RFC 4648 Base-N Encodings October 2006
A 65-character subset of US-ASCII is used, enabling 6 bits to be
represented per printable character. (The extra 65th character, "=",
is used to signify a special processing function.)
The encoding process represents 24-bit groups of input bits as output
strings of 4 encoded characters. Proceeding from left to right, a
24-bit input group is formed by concatenating 3 8-bit input groups.
These 24 bits are then treated as 4 concatenated 6-bit groups, each
of which is translated into a single character in the base 64
alphabet.
Each 6-bit group is used as an index into an array of 64 printable
characters. The character referenced by the index is placed in the
output string.
Table 1: The Base 64 Alphabet
Value Encoding Value Encoding Value Encoding Value Encoding
0 A 17 R 34 i 51 z
1 B 18 S 35 j 52 0
2 C 19 T 36 k 53 1
3 D 20 U 37 l 54 2
4 E 21 V 38 m 55 3
5 F 22 W 39 n 56 4
6 G 23 X 40 o 57 5
7 H 24 Y 41 p 58 6
8 I 25 Z 42 q 59 7
9 J 26 a 43 r 60 8
10 K 27 b 44 s 61 9
11 L 28 c 45 t 62 +
12 M 29 d 46 u 63 /
13 N 30 e 47 v
14 O 31 f 48 w (pad) =
15 P 32 g 49 x
16 Q 33 h 50 y
Special processing is performed if fewer than 24 bits are available
at the end of the data being encoded. A full encoding quantum is
always completed at the end of a quantity. When fewer than 24 input
bits are available in an input group, bits with value zero are added
(on the right) to form an integral number of 6-bit groups. Padding
at the end of the data is performed using the '=' character. Since
all base 64 input is an integral number of octets, only the following
cases can arise:
(1) The final quantum of encoding input is an integral multiple of 24
bits; here, the final unit of encoded output will be an integral
multiple of 4 characters with no "=" padding.
Josefsson Standards Track [Page 6]
RFC 4648 Base-N Encodings October 2006
(2) The final quantum of encoding input is exactly 8 bits; here, the
final unit of encoded output will be two characters followed by
two "=" padding characters.
(3) The final quantum of encoding input is exactly 16 bits; here, the
final unit of encoded output will be three characters followed by
one "=" padding character.
5. Base 64 Encoding with URL and Filename Safe Alphabet
The Base 64 encoding with an URL and filename safe alphabet has been
used in [12].
An alternative alphabet has been suggested that would use "~" as the
63rd character. Since the "~" character has special meaning in some
file system environments, the encoding described in this section is
recommended instead. The remaining unreserved URI character is ".",
but some file system environments do not permit multiple "." in a
filename, thus making the "." character unattractive as well.
The pad character "=" is typically percent-encoded when used in an
URI [9], but if the data length is known implicitly, this can be
avoided by skipping the padding; see section 3.2.
This encoding may be referred to as "base64url". This encoding
should not be regarded as the same as the "base64" encoding and
should not be referred to as only "base64". Unless clarified
otherwise, "base64" refers to the base 64 in the previous section.
This encoding is technically identical to the previous one, except
for the 62:nd and 63:rd alphabet character, as indicated in Table 2.
Josefsson Standards Track [Page 7]
RFC 4648 Base-N Encodings October 2006
Table 2: The "URL and Filename safe" Base 64 Alphabet
Value Encoding Value Encoding Value Encoding Value Encoding
0 A 17 R 34 i 51 z
1 B 18 S 35 j 52 0
2 C 19 T 36 k 53 1
3 D 20 U 37 l 54 2
4 E 21 V 38 m 55 3
5 F 22 W 39 n 56 4
6 G 23 X 40 o 57 5
7 H 24 Y 41 p 58 6
8 I 25 Z 42 q 59 7
9 J 26 a 43 r 60 8
10 K 27 b 44 s 61 9
11 L 28 c 45 t 62 - (minus)
12 M 29 d 46 u 63 _
13 N 30 e 47 v (underline)
14 O 31 f 48 w
15 P 32 g 49 x
16 Q 33 h 50 y (pad) =
6. Base 32 Encoding
The following description of base 32 is derived from [11] (with
corrections). This encoding may be referred to as "base32".
The Base 32 encoding is designed to represent arbitrary sequences of
octets in a form that needs to be case insensitive but that need not
be human readable.
A 33-character subset of US-ASCII is used, enabling 5 bits to be
represented per printable character. (The extra 33rd character, "=",
is used to signify a special processing function.)
The encoding process represents 40-bit groups of input bits as output
strings of 8 encoded characters. Proceeding from left to right, a
40-bit input group is formed by concatenating 5 8bit input groups.
These 40 bits are then treated as 8 concatenated 5-bit groups, each
of which is translated into a single character in the base 32
alphabet. When a bit stream is encoded via the base 32 encoding, the
bit stream must be presumed to be ordered with the most-significant-
bit first. That is, the first bit in the stream will be the high-
order bit in the first 8bit byte, the eighth bit will be the low-
order bit in the first 8bit byte, and so on.
Josefsson Standards Track [Page 8]
RFC 4648 Base-N Encodings October 2006
Each 5-bit group is used as an index into an array of 32 printable
characters. The character referenced by the index is placed in the
output string. These characters, identified in Table 3, below, are
selected from US-ASCII digits and uppercase letters.
Table 3: The Base 32 Alphabet
Value Encoding Value Encoding Value Encoding Value Encoding
0 A 9 J 18 S 27 3
1 B 10 K 19 T 28 4
2 C 11 L 20 U 29 5
3 D 12 M 21 V 30 6
4 E 13 N 22 W 31 7
5 F 14 O 23 X
6 G 15 P 24 Y (pad) =
7 H 16 Q 25 Z
8 I 17 R 26 2
Special processing is performed if fewer than 40 bits are available
at the end of the data being encoded. A full encoding quantum is
always completed at the end of a body. When fewer than 40 input bits
are available in an input group, bits with value zero are added (on
the right) to form an integral number of 5-bit groups. Padding at
the end of the data is performed using the "=" character. Since all
base 32 input is an integral number of octets, only the following
cases can arise:
(1) The final quantum of encoding input is an integral multiple of 40
bits; here, the final unit of encoded output will be an integral
multiple of 8 characters with no "=" padding.
(2) The final quantum of encoding input is exactly 8 bits; here, the
final unit of encoded output will be two characters followed by
six "=" padding characters.
(3) The final quantum of encoding input is exactly 16 bits; here, the
final unit of encoded output will be four characters followed by
four "=" padding characters.
(4) The final quantum of encoding input is exactly 24 bits; here, the
final unit of encoded output will be five characters followed by
three "=" padding characters.
(5) The final quantum of encoding input is exactly 32 bits; here, the
final unit of encoded output will be seven characters followed by
one "=" padding character.
Josefsson Standards Track [Page 9]
RFC 4648 Base-N Encodings October 2006
7. Base 32 Encoding with Extended Hex Alphabet
The following description of base 32 is derived from [7]. This
encoding may be referred to as "base32hex". This encoding should not
be regarded as the same as the "base32" encoding and should not be
referred to as only "base32". This encoding is used by, e.g.,
NextSECure3 (NSEC3) [10].
One property with this alphabet, which the base64 and base32
alphabets lack, is that encoded data maintains its sort order when
the encoded data is compared bit-wise.
This encoding is identical to the previous one, except for the
alphabet. The new alphabet is found in Table 4.
Table 4: The "Extended Hex" Base 32 Alphabet
Value Encoding Value Encoding Value Encoding Value Encoding
0 0 9 9 18 I 27 R
1 1 10 A 19 J 28 S
2 2 11 B 20 K 29 T
3 3 12 C 21 L 30 U
4 4 13 D 22 M 31 V
5 5 14 E 23 N
6 6 15 F 24 O (pad) =
7 7 16 G 25 P
8 8 17 H 26 Q
8. Base 16 Encoding
The following description is original but analogous to previous
descriptions. Essentially, Base 16 encoding is the standard case-
insensitive hex encoding and may be referred to as "base16" or "hex".
A 16-character subset of US-ASCII is used, enabling 4 bits to be
represented per printable character.
The encoding process represents 8-bit groups (octets) of input bits
as output strings of 2 encoded characters. Proceeding from left to
right, an 8-bit input is taken from the input data. These 8 bits are
then treated as 2 concatenated 4-bit groups, each of which is
translated into a single character in the base 16 alphabet.
Each 4-bit group is used as an index into an array of 16 printable
characters. The character referenced by the index is placed in the
output string.
Josefsson Standards Track [Page 10]
RFC 4648 Base-N Encodings October 2006
Table 5: The Base 16 Alphabet
Value Encoding Value Encoding Value Encoding Value Encoding
0 0 4 4 8 8 12 C
1 1 5 5 9 9 13 D
2 2 6 6 10 A 14 E
3 3 7 7 11 B 15 F
Unlike base 32 and base 64, no special padding is necessary since a
full code word is always available.
9. Illustrations and Examples
To translate between binary and a base encoding, the input is stored
in a structure, and the output is extracted. The case for base 64 is
displayed in the following figure, borrowed from [5].
+--first octet--+-second octet--+--third octet--+
|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|
+-----------+---+-------+-------+---+-----------+
|5 4 3 2 1 0|5 4 3 2 1 0|5 4 3 2 1 0|5 4 3 2 1 0|
+--1.index--+--2.index--+--3.index--+--4.index--+
The case for base 32 is shown in the following figure, borrowed from
[7]. Each successive character in a base-32 value represents 5
successive bits of the underlying octet sequence. Thus, each group
of 8 characters represents a sequence of 5 octets (40 bits).
1 2 3
01234567 89012345 67890123 45678901 23456789
+--------+--------+--------+--------+--------+
|< 1 >< 2| >< 3 ><|.4 >< 5.|>< 6 ><.|7 >< 8 >|
+--------+--------+--------+--------+--------+
<===> 8th character
<====> 7th character
<===> 6th character
<====> 5th character
<====> 4th character
<===> 3rd character
<====> 2nd character
<===> 1st character
Josefsson Standards Track [Page 11]
RFC 4648 Base-N Encodings October 2006
The following example of Base64 data is from [5], with corrections.
Input data: 0x14fb9c03d97e
Hex: 1 4 f b 9 c | 0 3 d 9 7 e
8-bit: 00010100 11111011 10011100 | 00000011 11011001 01111110
6-bit: 000101 001111 101110 011100 | 000000 111101 100101 111110
Decimal: 5 15 46 28 0 61 37 62
Output: F P u c A 9 l +
Input data: 0x14fb9c03d9
Hex: 1 4 f b 9 c | 0 3 d 9
8-bit: 00010100 11111011 10011100 | 00000011 11011001
pad with 00
6-bit: 000101 001111 101110 011100 | 000000 111101 100100
Decimal: 5 15 46 28 0 61 36
pad with =
Output: F P u c A 9 k =
Input data: 0x14fb9c03
Hex: 1 4 f b 9 c | 0 3
8-bit: 00010100 11111011 10011100 | 00000011
pad with 0000
6-bit: 000101 001111 101110 011100 | 000000 110000
Decimal: 5 15 46 28 0 48
pad with = =
Output: F P u c A w = =
10. Test Vectors
BASE64("") = ""
BASE64("f") = "Zg=="
BASE64("fo") = "Zm8="
BASE64("foo") = "Zm9v"
BASE64("foob") = "Zm9vYg=="
BASE64("fooba") = "Zm9vYmE="
BASE64("foobar") = "Zm9vYmFy"
BASE32("") = ""
BASE32("f") = "MY======"
BASE32("fo") = "MZXQ===="
Josefsson Standards Track [Page 12]
RFC 4648 Base-N Encodings October 2006
BASE32("foo") = "MZXW6==="
BASE32("foob") = "MZXW6YQ="
BASE32("fooba") = "MZXW6YTB"
BASE32("foobar") = "MZXW6YTBOI======"
BASE32-HEX("") = ""
BASE32-HEX("f") = "CO======"
BASE32-HEX("fo") = "CPNG===="
BASE32-HEX("foo") = "CPNMU==="
BASE32-HEX("foob") = "CPNMUOG="
BASE32-HEX("fooba") = "CPNMUOJ1"
BASE32-HEX("foobar") = "CPNMUOJ1E8======"
BASE16("") = ""
BASE16("f") = "66"
BASE16("fo") = "666F"
BASE16("foo") = "666F6F"
BASE16("foob") = "666F6F62"
BASE16("fooba") = "666F6F6261"
BASE16("foobar") = "666F6F626172"
Josefsson Standards Track [Page 13]
RFC 4648 Base-N Encodings October 2006
11. ISO C99 Implementation of Base64
An ISO C99 implementation of Base64 encoding and decoding that is
believed to follow all recommendations in this RFC is available from:
http://josefsson.org/base-encoding/
This code is not normative.
The code could not be included in this RFC for procedural reasons
(RFC 3978 section 5.4).
12. Security Considerations
When base encoding and decoding is implemented, care should be taken
not to introduce vulnerabilities to buffer overflow attacks, or other
attacks on the implementation. A decoder should not break on invalid
input including, e.g., embedded NUL characters (ASCII 0).
If non-alphabet characters are ignored, instead of causing rejection
of the entire encoding (as recommended), a covert channel that can be
used to "leak" information is made possible. The ignored characters
could also be used for other nefarious purposes, such as to avoid a
string equality comparison or to trigger implementation bugs. The
implications of ignoring non-alphabet characters should be understood
in applications that do not follow the recommended practice.
Similarly, when the base 16 and base 32 alphabets are handled case
insensitively, alteration of case can be used to leak information or
make string equality comparisons fail.
When padding is used, there are some non-significant bits that
warrant security concerns, as they may be abused to leak information
or used to bypass string equality comparisons or to trigger
implementation problems.
Base encoding visually hides otherwise easily recognized information,
such as passwords, but does not provide any computational
confidentiality. This has been known to cause security incidents
when, e.g., a user reports details of a network protocol exchange
(perhaps to illustrate some other problem) and accidentally reveals
the password because she is unaware that the base encoding does not
protect the password.
Base encoding adds no entropy to the plaintext, but it does increase
the amount of plaintext available and provide a signature for
cryptanalysis in the form of a characteristic probability
distribution.
Josefsson Standards Track [Page 14]
RFC 4648 Base-N Encodings October 2006
13. Changes Since RFC 3548
Added the "base32 extended hex alphabet", needed to preserve sort
order of encoded data.
Referenced IMAP for the special Base64 encoding used there.
Fixed the example copied from RFC 2440.
Added security consideration about providing a signature for
cryptoanalysis.
Added test vectors.
Fixed typos.
14. Acknowledgements
Several people offered comments and/or suggestions, including John E.
Hadstate, Tony Hansen, Gordon Mohr, John Myers, Chris Newman, and
Andrew Sieber. Text used in this document are based on earlier RFCs
describing specific uses of various base encodings. The author
acknowledges the RSA Laboratories for supporting the work that led to
this document.
This revised version is based in parts on comments and/or suggestions
made by Roy Arends, Eric Blake, Brian E Carpenter, Elwyn Davies, Bill
Fenner, Sam Hartman, Ted Hardie, Per Hygum, Jelte Jansen, Clement
Kent, Tero Kivinen, Paul Kwiatkowski, and Ben Laurie.
15. Copying Conditions
Copyright (c) 2000-2006 Simon Josefsson
Regarding the abstract and sections 1, 3, 8, 10, 12, 13, and 14 of
this document, that were written by Simon Josefsson ("the author",
for the remainder of this section), the author makes no guarantees
and is not responsible for any damage resulting from its use. The
author grants irrevocable permission to anyone to use, modify, and
distribute it in any way that does not diminish the rights of anyone
else to use, modify, and distribute it, provided that redistributed
derivative works do not contain misleading author or version
information and do not falsely purport to be IETF RFC documents.
Derivative works need not be licensed under similar terms.
Josefsson Standards Track [Page 15]
RFC 4648 Base-N Encodings October 2006
16. References
16.1. Normative References
[1] Cerf, V., "ASCII format for network interchange", RFC 20,
October 1969.
[2] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
16.2. Informative References
[3] Linn, J., "Privacy Enhancement for Internet Electronic Mail:
Part I: Message Encryption and Authentication Procedures", RFC
1421, February 1993.
[4] Freed, N. and N. Borenstein, "Multipurpose Internet Mail
Extensions (MIME) Part One: Format of Internet Message Bodies",
RFC 2045, November 1996.
[5] Callas, J., Donnerhacke, L., Finney, H., and R. Thayer,
"OpenPGP Message Format", RFC 2440, November 1998.
[6] Arends, R., Austein, R., Larson, M., Massey, D., and S. Rose,
"DNS Security Introduction and Requirements", RFC 4033, March
2005.
[7] Klyne, G. and L. Masinter, "Identifying Composite Media
Features", RFC 2938, September 2000.
[8] Crispin, M., "INTERNET MESSAGE ACCESS PROTOCOL - VERSION
4rev1", RFC 3501, March 2003.
[9] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
Resource Identifier (URI): Generic Syntax", STD 66, RFC 3986,
January 2005.
[10] Laurie, B., Sisson, G., Arends, R., and D. Blacka, "DNSSEC Hash
Authenticated Denial of Existence", Work in Progress, June
2006.
[11] Myers, J., "SASL GSSAPI mechanisms", Work in Progress, May
2000.
[12] Wilcox-O'Hearn, B., "Post to P2P-hackers mailing list",
http://zgp.org/pipermail/p2p-hackers/2001-September/
000315.html, September 2001.
Josefsson Standards Track [Page 16]
RFC 4648 Base-N Encodings October 2006
Author's Address
Simon Josefsson
SJD
EMail: simon@josefsson.org
Josefsson Standards Track [Page 17]
RFC 4648 Base-N Encodings October 2006
Full Copyright Statement
Copyright (C) The Internet Society (2006).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Josefsson Standards Track [Page 18]