💾 Archived View for spam.works › mirrors › textfiles › programming › diagcode.txt captured on 2023-07-22 at 20:43:27.
⬅️ Previous capture (2023-06-16)
-=-=-=-=-=-=-
Listing of IBM PC Diagnostic Error Codes Jerry Schneider Capital PC User Group Washington, DC All personal computer error codes for the Power On Self Test, General Diagnostics, and Advanced Diagnostics consist of a device number followed by two digits other than 00. (The device number plus 00 indicates successful completion of the test.) This list is a compilation from various sources, including USENET's Info-IBMPC Digest, IBM Technical Reference Manuals, and IBM Hardware, Maintenance and Service manuals. Code Description 01x Undetermined problem errors. 02x Power supply errors. 1xx System board errors. 101 System board error - Interrupt failure. 102 System board error - Timer failure. 103 System board error - Timer interrupt failure. 104 System board error - Protected mode failure. 105 System board error - Last 8042 command not accepted. 106 System board error - Converting logic test. 107 System board error - Hot NMI test. 108 System board error - Timer bus test. 109 Direct memory access test error. 121 Unexpected hardware interrupts occurred. 131 Cassette wrap test failed. 152 161 System Options Error-(Run SETUP) [Battery failure]. 162 System options not set correctly-(Run SETUP). 163 Time and date not set-(Run SETUP). 164 Memory size error-(Run SETUP). 199 User-indicated configuration not correct. 2xx Memory (RAM) errors. 201 Memory test failed. 202 Memory address error. 203 Memory address error. 3xx Keyboard errors. 301 Keyboard did not respond to software reset correctly, or a stuck key failure was detected. If a stuck key was detected, the scan code for the key is dis- played in hexadecimal. For example, the error code 49 301 indicates that key 73, the PgUp key, has failed (49 hex = 73 decimal). 302 User-indicated error from the keyboard test, or AT keylock is locked. 303 Keyboard or system unit error. 304 Keyboard or system unit error; CMOS does not match system. 4xx Monochrome monitor errors. 401 Monochrome memory test, horizontal sync frequency test, or video test failed. 408 User-indicated display attributes failure. 416 User-indicated character set failure. 424 User-indicated 80 X 25 mode failure. 432 Parallel port test failed (monochrome adapter). 5xx Color monitor errors. 501 Color memory test failed, horizontal sync frequency test, or video test failed. 508 User-indicated display attribute failure. 516 User-indicated character set failure. 524 User-indicated 80 X 25 mode failure. 532 User-indicated 40 X 25 mode failure. 540 User-indicated 320 X 200 graphics mode failure. 548 User-indicated 640 X 200 graphics mode failure. 6xx Diskette drive errors. 601 Diskette power-on diagnostics test failed. 602 Diskette test failed; boot record is not valid. 606 Diskette verify function failed. 607 Write-protected diskette. 608 Bad command diskette status returned. 610 Diskette initialization failed. 611 Timeout - diskette status returned. 612 Bad NEC - diskette status returned. 613 Bad DMA - diskette status returned. 621 Bad seek - diskette status returned. 622 Bad CRC - diskette status returned. 623 Record not found - diskette status returned. 624 Bad address mark - diskette status returned. 625 Bad NEC seek - diskette status returned. 626 Diskette data compare error. 7xx 8087 or 80287 math coprocessor errors. 9xx Parallel printer adapter errors. 901 Parallel printer adapter test failed. 10xx Reserved for parallel printer adapter. 11xx Asynchronous communications adapter errors. 1101 Asynchronous communications adapter test failed. 12xx Alternate asynchronous communications adapter errors. 1201 Alternate asynchronous communications adapter test failed. 13xx Game control adapter errors. 1301 Game control adapter test failed. 1302 Joystick test failed. 14xx Printer errors. 1401 Printer test failed. 1404 Matrix printer failed. 15xx Synchronous data link control (SDLC) communications adapter errors. 1510 8255 port B failure. 1511 8255 port A failure. 1512 8255 port C failure. 1513 8253 timer 1 did not reach terminal count. 1514 8253 timer 1 stuck on. 1515 8253 timer 0 did not reach terminal count. 1516 8253 timer 0 stuck on. 1517 8253 timer 2 did not reach terminal count. 1518 8253 timer 2 stuck on. 1519 8273 port B error. 1520 8273 port A error. 1521 8273 command/read timeout. 1522 Interrupt level 4 failure. 1523 Ring Indicate stuck on. 1524 Receive clock stuck on. 1525 Transmit clock stuck on. 1526 Test indicate stuck on. 1527 Ring indicate not on. 1528 Receive clock not on. 1529 Transmit clock not on. 1530 Test indicate not on. 1531 Data set ready not on. 1532 Carrier detect not on. 1533 Clear to send not on. 1534 Data set ready stuck on. 1536 Clear to send stuck on. 1537 Level 3 interrupt failure. 1538 Receive interrupt results error. 1539 Wrap data miscompare. 1540 DMA channel 1 error. 1541 DMA channel 1 error. 1542 Error in 8273 error checking or status reporting. 1547 Stray interrupt level 4. 1548 Stray interrupt level 3. 1549 Interrupt presentation sequence timeout. 16xx Display emulation errors (327x, 5520, 525x). 17xx Fixed disk errors. 1701 Fixed disk POST error. 1702 Fixed disk adapter error. 1703 Fixed disk drive error. 1704 Fixed disk adapter or drive error. 1780 Fixed disk 0 failure. 1781 Fixed disk 1 failure. 1782 Fixed disk controller failure. 1790 Fixed disk 0 error. 1791 Fixed disk 1 error. 18xx I/O expansion unit errors. 1801 I/O expansion unit POST error. 1810 Enable/Disable failure. 1811 Extender card warp test failed (disabled). 1812 High order address lines failure (disabled). 1813 Wait state failure (disabled). 1814 Enable/Disable could not be set on. 1815 Wait state failure (disabled). 1816 Extender card warp test failed (enabled). 1817 High order address lines failure (enabled). 1818 Disable not functioning. 1819 Wait request switch not set correctly. 1820 Receiver card wrap test failure. 1821 Receiver high order address lines failure. 19xx 3270 PC attachment card errors. 20xx Binary synchronous communications (BSC) adapter errors. 2010 8255 port A failure. 2011 8255 port B failure. 2012 8255 port C failure. 2013 8253 timer 1 did not reach terminal count. 2014 8253 timer 1 stuck on. 2016 8253 timer 2 did not reach terminal count, or timer 2 stuck on. 2017 8251 Data set ready failed to come on. 2018 8251 Clear to send not sensed. 2019 8251 Data set ready stuck on. 2020 8251 Clear to send stuck on. 2021 8251 hardware reset failed. 2022 8251 software reset failed. 2023 8251 software "error reset" failed. 2024 8251 transmit ready did not come on. 2025 8251 receive ready did not come on. 2026 8251 could not force "overrun" error status. 2027 Interrupt failure - no timer interrupt. 2028 Interrupt failure - transmit, replace card or planar. 2029 Interrupt failure - transmit, replace card. 2030 Interrupt failure - receive, replace card or planar. 2031 Interrupt failure - receive, replace card. 2033 Ring indicate stuck on. 2034 Receive clock stuck on. 2035 Transmit clock stuck on. 2036 Test indicate stuck on. 2037 Ring indicate stuck on. 2038 Receive clock not on. 2039 Transmit clock not on. 2040 Test indicate not on. 2041 Data set ready not on. 2042 Carrier detect not on. 2043 Clear to send not on. 2044 Data set ready stuck on. 2045 Carrier detect stuck on. 2046 Clear to send stuck on. 2047 Unexpected transmit interrupt. 2048 Unexpected receive interrupt. 2049 Transmit data did not equal receive data. 2050 8251 detected overrun error. 2051 Lost data set ready during data wrap. 2052 Receive timeout during data wrap. 21xx Alternate binary synchronous communications adapter errors. 2110 8255 port A failure. 2111 8255 port B failure. 2112 8255 port C failure. 2113 8253 timer 1 did not reach terminal count. 2114 8253 timer 1 stuck on. 2115 8253 timer 2 did not reach terminal count, or timer 2 stuck on. 2116 8251 Data set ready failed to come on. 2117 8251 Clear to send not sensed. 2118 8251 Data set ready stuck on. 2119 8251 Clear to send stuck on. 2120 8251 hardware reset failed. 2121 8251 software reset failed. 2122 8251 software "error reset" failed. 2123 8251 transmit ready did not come on. 2124 8251 receive ready did not come on. 2125 8251 could not force "overrun" error status. 2126 Interrupt failure - no timer interrupt. 2128 Interrupt failure - transmit, replace card or planar. 2129 Interrupt failure - transmit, replace card. 2130 Interrupt failure - receive, replace card or planar. 2131 Interrupt failure - receive, replace card. 2133 Ring indicate stuck on. 2134 Receive clock stuck on. 2135 Transmit clock stuck on. 2136 Test indicate stuck on. 2137 Ring indicate stuck on. 2138 Receive clock not on. 2139 Transmit clock not on. 2140 Test indicate not on. 2141 Data set ready not on. 2142 Carrier detect not on. 2143 Clear to send not on. 2144 Data set ready stuck on. 2145 Carrier detect stuck on. 2146 Clear to send stuck on. 2147 Unexpected transmit interrupt. 2148 Unexpected receive interrupt. 2149 Transmit data did not equal receive data. 2150 8251 detected overrun error. 2151 Lost data set ready during data wrap. 2152 Receive timeout during data wrap. 22xx Cluster adapter errors. 24xx Enhanced graphics adapter errors. 26xx XT/370 error codes 27xx XT/370 error codes 29xx Color matrix printer errors. 2901 2902 2904 30xx Primary PC Network Adapter Error 3001 CPU Failure 3002 ROM Failure 3003 ID Failure 3004 RAM Failure 3005 HIC Failure 3006 +/- 12v Failed 3007 Digital Loopback Failure 3008 Host Detected HIC Failure 3009 Sync Fail & No Go Bit 3010 HIC Test OK & No Go Bit 3011 Go Bit & No CMD 41 3012 Card not present 3013 Digital Failure ( Fall Thru ) 3015 Analog Failure 3041 Hot Carrier (not this card) 3042 Hot Carrier (THIS CARD !!) 31xx Secondary PC Network Adapter Error 3101 CPU Failure 3102 ROM Failure 3103 ID Failure 3104 RAM Failure 3105 HIC Failure 3106 +/- 12v Failed 3107 Digital Loopback Failure 3108 Host Detected HIC Failure 3109 Sync Fail & No Go Bit 3110 HIC Test OK & No Go Bit 3111 Go Bit & No CMD 41 3112 Card not present 3113 Digital Failure ( Fall Thru ) 3115 Analog Failure 3141 Hot Carrier (not this card) 3142 Hot Carrier (THIS CARD !!) 33xx Compact printer errors. Interrupt failure - receive, replace card or planar. 2131 Interrupt failure - receive, replac