💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc4993.txt captured on 2023-07-22 at 19:43:00.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group A. Newton
Request for Comments: 4993 VeriSign, Inc.
Category: Standards Track August 2007
A Lightweight UDP Transfer Protocol
for the Internet Registry Information Service
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Abstract
This document describes a lightweight UDP transfer protocol for the
Internet Registry Information Service (IRIS). This transfer protocol
uses a single packet for every request and response, and optionally
employs compression over the contents of the packet.
Newton Standards Track [Page 1]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
Table of Contents
1. Introduction ....................................................3
2. Document Terminology ............................................3
3. Packet Format ...................................................4
3.1. Payload Descriptor .........................................4
3.1.1. Payload Request Descriptor ..........................4
3.1.2. Payload Response Descriptor .........................5
3.1.3. Payload Header ......................................6
3.1.4. Payload Types .......................................6
3.1.5. Version Information .................................7
3.1.6. Size Information ....................................8
3.1.7. Other Information ...................................8
4. Interactions ....................................................9
5. Internationalization Considerations ............................10
6. IRIS Transport Mapping Definitions .............................10
6.1. URI Scheme ................................................10
6.2. Application Protocol Label ................................10
7. IANA Considerations ............................................10
7.1. Registrations .............................................10
7.1.1. URI Scheme Registration ............................10
7.1.2. Well-known UDP Port Registration ...................11
7.1.3. S-NAPTR Registration ...............................11
8. Security Considerations ........................................12
9. References .....................................................13
9.1. Normative References ......................................13
9.2. Informative References ....................................13
Appendix A. Examples ..............................................14
Appendix B. Contributors ..........................................18
Newton Standards Track [Page 2]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
1. Introduction
Using Straightforward Name Authority Pointers (S-NAPTR) [4], IRIS has
the ability to define the use of multiple application transports or
transfer protocols for different types of registry services, all at
the discretion of the server operator. The UDP transfer protocol
defined in this document is completely independent of the registry
types for which it can carry data.
The binding of this UDP transfer protocol to IRIS is called IRIS-LWZ
(for IRIS Lightweight using Compression). Its message exchange
pattern is simple: a client sends a request in one UDP packet, and a
server responds with an answer in one UDP packet.
IRIS-LWZ packets are composed of two parts, a binary payload
descriptor and a request/response transaction payload. The request/
response transaction payload may be compressed using the DEFLATE [1]
algorithm.
2. Document Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [6].
Octet fields with numeric values are given according to the
conventions in RFC 1166 [10]: the leftmost bit of the whole field is
the most significant bit; when a multi-octet quantity is transmitted
the most significant octet is transmitted first. Bits signifying
flags in an octet are numbered according to the conventions of RFC
1166 [10]: bit 0 is the most significant bit and bit 7 is the least
significant bit. When a diagram describes a group of octets, the
order of transmission for the octets starts from the left.
Newton Standards Track [Page 3]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
3. Packet Format
The packet format for IRIS-LWZ is as follows:
+------------+---------+
field | payload | payload |
| descriptor | |
+------------+---------+
octets 3 or 6..261* 0..n
* In request packets, the payload descriptor can vary in length
from 6 to 261 octets (i.e., 6..261). In response packets, the
payload descriptor is always 3 octets.
IRIS-LWZ Packet
Each IRIS-LWZ query or response is contained in a single UDP
packet. Servers MUST be prepared to accept packets as large as
4000 octets, and clients MUST NOT send packets larger than 4000
octets.
3.1. Payload Descriptor
The payload descriptor has two different formats, one for a
request and one for a response. However, each format shares a
common 1-octet payload header described in Section 3.1.3.
3.1.1. Payload Request Descriptor
The payload descriptor for request packets varies from 6 to 261
octets in length and has the following format:
+--------+-------------+----------+-----------+-----------+
field | header | transaction | maximum | authority | authority |
| | ID | response | length | |
| | | length | | |
+--------+-------------+----------+-----------+-----------+
octets 1 2 2 1 0..255
Request Payload Descriptor
These fields have the following meanings:
o header - as described in Section 3.1.3.
o transaction ID - a 16-bit value identifying the transaction. This
value will be returned in the payload response descriptor (Section
3.1.2) and can be used by clients to match requests with
Newton Standards Track [Page 4]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
responses. Clients SHOULD NOT use sequential values (see Section
8). Clients MUST NOT set all the bits in this value to 1 (i.e.,
use a value of 0xFFFF).
o maximum response length - the total length of the UDP packet
(i.e., UDP header length + payload descriptor length + XML payload
length) that should not be exceeded when responding to this
request. If the server cannot provide a response that is equal to
or less than this value, then it MUST respond with size
information (Section 3.1.6).
o authority length - the length of the authority field in this
payload descriptor.
o authority - a string of octets describing the authority against
which this request is to be executed. See [3] for the definition
and description of an authority. The number of octets in this
string MUST be no more and no less than the number specified by
the authority length.
3.1.2. Payload Response Descriptor
The payload descriptor for response packets is always 3 octets and
consists of a payload header (Section 3.1.3) and a transaction ID.
+--------+-------------+
field | header | transaction |
| | ID |
+--------+-------------+
octets 1 2
Payload Response Descriptor
The purpose of the transaction ID is to allow clients to match
requests to responses. A value of 0xFFFF is reserved for server use.
The value of the transaction ID is as follows:
1. If the transaction ID in the corresponding request could not be
read due to truncation, servers MUST use a transaction ID with
all bits set to 1 (i.e., a value of OxFFFF) and send a descriptor
error (see Section 3.1.7).
2. If the transaction ID in the corresponding request is a value of
0xFFFF, servers MUST use a transaction ID of 0xFFFF and send a
descriptor error (see Section 3.1.7).
3. Otherwise, the transaction ID MUST be the value of the
transaction ID of the corresponding request.
Newton Standards Track [Page 5]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
3.1.3. Payload Header
The bits of the payload header are ordered according to RFC 1166
[10], where bit 0 is the most significant and bit 7 is the least
significant. Each bit in the 1-octet payload header has the
following meaning:
o bits 0 and 1 - version number ('V' field) - If 0 (both bits are
zero), the protocol is the version defined in this document.
Otherwise, the rest of the bits in the header and the payload may
be interpreted as another version.
o bit 2 - request/response flag ('RR' flag) - If 0, this packet is a
request (Section 3.1.1) packet. If 1, this packet is a response
(Section 3.1.2) packet.
o bits 3 - payload deflated ('PD' flag) - If 1, the payload is
compressed using the DEFLATE [1] algorithm.
o bit 4 - deflate supported ('DS' flag) - If 1, the sender of this
packet supports compression using the DEFLATE algorithm. When
this bit is 0 in a request, the payload of the response MUST NOT
be compressed with DEFLATE.
o bit 5 - reserved - This MUST be 0.
o bits 6 and 7 - The value of these bits indicates payload types
(Section 3.1.4) ('PT' field).
3.1.4. Payload Types
A payload type indicates the type of content in the UDP packet
following the payload descriptor. Some payload types have no meaning
in request packets, and some payload types differ in meaning between
requests and responses. Some payload types indicate an empty
payload.
The payload type values in binary are as follows:
00 - xml payload ('xml' type). The payload is either an IRIS-
based XML request or an IRIS-based XML response.
01 - version info ('vi' type). In a request packet, this payload
type indicates that the server is to respond with version
information (Section 3.1.5), and that the payload is empty. In a
response packet, this payload type indicates that the payload is
version information (Section 3.1.5).
Newton Standards Track [Page 6]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
10 - size info ('si' type). This payload type has no meaning in a
request packet and is a descriptor error. In a response packet,
this payload type indicates that the payload is size information
(Section 3.1.6).
11 - other info ('oi' type). This payload type has no meaning in
a request packet and is a descriptor error. In a response packet,
this payload type indicates that the payload is other information
(Section 3.1.7).
3.1.5. Version Information
A payload type with version information ('vi') MUST be conformant to
the XML defined in [8] and use the <versions> element as the root
element.
In the context of IRIS-LWZ, the protocol identifiers for these
elements are as follows:
<transferProtocol> - the value "iris.lwz1" to indicate the
protocol specified in this document.
<application> - the XML namespace identifier for IRIS [3].
<dataModel> - the XML namespace identifier for IRIS registries.
This document defines no extension identifiers and no authentication
mechanism identifiers.
Servers SHOULD send version information in the following cases:
1. In response to a version information request (i.e., the PT field
is set to 'vi').
2. The version in a payload descriptor header does not match a
version the server supports.
3. The IRIS-based XML payload does not match a version the server
supports.
The protocols identified by the <transferProtocol> element MUST only
indicate protocols running on the same socket as the sender of the
corresponding response. In other words, while a server operator may
also be running IRIS-XPC [9], this XML instance is only intended to
describe version negotiation for IRIS-LWZ.
Newton Standards Track [Page 7]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
The octet size for the 'requestSizeOctets' and 'responseSizeOctets'
attributes of the <tranferProtocol> element are defined in Section
3.1.6.
3.1.6. Size Information
A payload type with size information ('si') MUST be conformant to the
XML defined in [8] and use the <size> element as the root element.
Octet counts provided by this information are defined as the total
length of the UDP packet (i.e., UDP header length + payload
descriptor length + XML payload length).
3.1.7. Other Information
A payload type with other information ('oi') MUST be conformant to
the XML defined in [8] and use the <other> element as the root
element.
The values for the 'type' attribute of <other> are as follows:
'descriptor-error' - indicates there was an error decoding the
descriptor. Servers SHOULD send a descriptor error in the
following cases:
1. When a request is received with a payload type indicating size
information (i.e., the PT field is 'si').
2. When a request is received with a payload type indicating
other information (i.e., the PT field is 'oi').
3. When a request is sent with a transaction ID of 0xFFFF (which
is reserved for server use).
4. When a request is received with an incomplete or truncated
payload descriptor.
5. When reserved bits in the payload descriptor are set to values
other than zero.
'payload-error' - indicates there was an error interpreting the
payload. Servers MUST send a payload error if they receive XML
(i.e., the PT field is set to 'xml') and the XML cannot be parsed.
'system-error' - indicates that the receiver cannot process the
request due to a condition not related to this protocol. Servers
SHOULD send a system-error when they are capable of responding to
requests but not capable of processing requests.
Newton Standards Track [Page 8]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
'authority-error' - indicates that the intended authority
specified in the corresponding request is not served by the
receiver. Servers SHOULD send an authority error when they
receive a request directed to an authority other than those they
serve.
'no-inflation-support-error' - indicates that the receiver does
not support payloads that have been compressed with DEFLATE [1].
Servers MUST send this error when they receive a request that has
been compressed with DEFLATE but they do not support inflation.
4. Interactions
The intent of IRIS-LWZ is to utilize UDP for IRIS requests and
responses when UDP is appropriate. Not all IRIS requests and
responses will be able to utilize UDP and may require the use of
other transfer protocols (i.e., IRIS-XPC [9] and/or Blocks Extensible
Exchange Protocol (BEEP)). The following strategy SHOULD be used:
1. If a request requires authentication, confidentiality, or other
security, use another transfer protocol. IRIS-XPC [9] is
RECOMMENDED.
2. The maximum packet size should be calculated as follows:
a. If the path MTU is unknown, the maximum packet size MUST be
1500 octets.
b. If the path MTU is known, the maximum packet size MUST NOT
exceed the path MTU and MUST NOT exceed 4000 octets.
3. If a request is less than or equal to the maximum packet size,
send it uncompressed.
4. If a request can be compressed to a size less than or equal to
the maximum packet size, send the request using compression.
Otherwise, use another transfer protocol. In cases where another
transfer protocol is needed, IRIS-XPC [9] is RECOMMENDED.
5. If a request yields a size error, send the request with another
transfer protocol. IRIS-XPC [9] is RECOMMENDED.
For retransmission of requests considered to be unanswered, a client
SHOULD retransmit using a timeout value initially set to 1 second.
This timeout value SHOULD be doubled for every retransmission, and a
client SHOULD NOT retransmit any request once the timeout value has
reached 60 seconds.
Newton Standards Track [Page 9]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
Clients that use timeout values other than the recommendations above
MUST allocate or have allocated dedicated network resources that will
ensure fairness to other network packets and avoid network
congestion.
Clients MUST NOT have more than one outstanding request (i.e., an
unanswered request that has not timed out) at a time unless they
allocate or have been allocated dedicated network bandwidth and
resources reserved specifically for this purpose.
Finally, if a client intends multiple requests to the same server in
a short amount of time, this protocol offers no real advantage over
IRIS-XPC [9]. In such a case, IRIS-XPC is RECOMMENDED to be used as
it would be similarly or more efficient and would offer greater
response sizes and allow better security.
5. Internationalization Considerations
XML processors are obliged to recognize both UTF-8 and UTF-16 [2]
encodings. Use of the XML defined by [8] MUST NOT use any other
character encodings other than UTF-8 or UTF-16.
6. IRIS Transport Mapping Definitions
This section lists the definitions required by IRIS [3] for transport
mappings.
6.1. URI Scheme
See Section 7.1.1.
6.2. Application Protocol Label
See Section 7.1.3.
7. IANA Considerations
7.1. Registrations
7.1.1. URI Scheme Registration
URL scheme name: iris.lwz
Status: permanent
URL scheme syntax: defined in [3].
Character encoding considerations: as defined in RFC 3986 [5].
Newton Standards Track [Page 10]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
Intended usage: identifies an IRIS entity made available using XML
over UDP
Applications using this scheme: defined in IRIS [3].
Interoperability considerations: n/a
Security Considerations: defined in Section 8.
Relevant Publications: IRIS [3].
Contact Information: Andrew Newton <andy@hxr.us>
Author/Change controller: the IESG
7.1.2. Well-known UDP Port Registration
Protocol Number: UDP
UDP Port Number: 715
Message Formats, Types, Opcodes, and Sequences: defined in Sections 3
and 3.1.
Functions: defined in IRIS [3].
Use of Broadcast/Multicast: none
Proposed Name: IRIS-LWZ
Short name: iris.lwz
Contact Information: Andrew Newton <andy@hxr.us>
7.1.3. S-NAPTR Registration
Application Protocol Label (see [4]): iris.lwz
Intended usage: identifies an IRIS server using XML over UDP
Interoperability considerations: n/a
Security Considerations: defined in Section 8.
Relevant Publications: IRIS [3].
Contact Information: Andrew Newton <andy@hxr.us>
Newton Standards Track [Page 11]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
Author/Change controller: the IESG
8. Security Considerations
IRIS-LWZ is intended for serving public data; it provides no in-band
mechanisms for authentication or confidentiality. Any application
with these needs must provide out-of-band mechanisms (e.g., IPsec),
or use the IRIS transfer protocols that provide such capabilities,
such as IRIS-XPC [9].
Due to this lack of security, it is possible for an attacker to alter
IRIS-LWZ messages sent from the client to the server and from the
server to the client. Such an attack can result in denying usage of
an IRIS service or in supplying false information to end users and
many other scenarios.
Because IRIS-LWZ is a UDP-based protocol, it is possible for servers
using IRIS-LWZ to be used in a type of distributed denial-of-service
attack known as a reflection attack. This type of attack affects
other types of UDP-using protocols, such as DNS. Server operators
should be prepared to apply the same methods used for mitigating
reflection attacks with other protocols, such as DNS, when using
IRIS-LWZ. All operators should follow the advice given in BCP 38
[7].
IRIS-LWZ uses transaction IDs in the payload descriptors to better
enable a client to match a response to a request. By randomizing the
transaction IDs being used (i.e., not using sequential numbers),
attackers flooding the network with a large amount of spoofed packets
have a lesser chance of succeeding with the attack. This measure is
not guaranteed to thwart any such attack. Client implementers MUST
take appropriate measures when ignoring this advice.
Newton Standards Track [Page 12]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
9. References
9.1. Normative References
[1] Deutsch, P., "DEFLATE Compressed Data Format Specification
version 1.3", RFC 1951, May 1996.
[2] The Unicode Consortium, "The Unicode Standard, Version 3", ISBN
0-201-61633-5, 2000, <The Unicode Standard, Version 3>.
[3] Newton, A. and M. Sanz, "IRIS: The Internet Registry
Information Service (IRIS) Core Protocol", RFC 3981, January
2005.
[4] Daigle, L. and A. Newton, "Domain-Based Application Service
Location Using SRV RRs and the Dynamic Delegation Discovery
Service (DDDS)", RFC 3958, January 2005.
[5] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
Resource Identifier (URI): Generic Syntax", STD 66, RFC 3986,
January 2005.
[6] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", RFC 2119, BCP 14, March 1997.
[7] Ferguson, P. and D. Senie, "Network Ingress Filtering:
Defeating Denial of Service Attacks which employ IP Source
Address Spoofing", BCP 38, RFC 2827, May 2000.
[8] Newton, A., "A Common Schema for Internet Registry Information
Service Transfer Protocols", RFC 4991, August 2007.
[9] Newton, A., "XML Pipelining with Chunks for the Internet
Registry Information Service", RFC 4992, August 2007.
9.2. Informative References
[10] Kirkpatrick, S., Stahl, M., and M. Recker, "Internet numbers",
RFC 1166, July 1990.
Newton Standards Track [Page 13]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
Appendix A. Examples
This section gives examples of IRIS-LWZ exchanges. Lines beginning
with "C:" denote data sent by the client to the server, and lines
beginning with "S:" denote data sent by the server to the client.
Following the "C:" or "S:", the line contains either octet values in
hexadecimal notation with comments or XML fragments. No line
contains both octet values with comments and XML fragments. Comments
are contained within parentheses.
Newton Standards Track [Page 14]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
The following example demonstrates an IRIS client requesting a lookup
of 'AUP' in the 'local' entity class of a 'dreg1' registry. The
client passes a bag (see [3]) with the search request. The server
responds with a 'nameNotFound' response and an explanation.
C: (request packet)
C: 0x08 (header: V=0,RR=request,PD=no,DS=yes,PT=xml)
C: 0x03 0xA4 (transaction ID=932)
C: 0x05 0xDA (maximum response size=1498)
C: 0x09 (authority length=9)
C: (authority="localhost")
C: 0x6c 0x6f 0x63 0x61 0x6c 0x68 0x6f 0x73 0x74
C: (IRIS XML request)
C: <request xmlns="urn:ietf:params:xml:ns:iris1"
C: xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" >
C: <searchSet>
C: <bag>
C: <simpleBag xmlns="http://example.com/">
C: <salt>127.0.0.1:3434</salt>
C: <md5>4LnQ1KdCahzyvwBqJis5rw==</md5>
C: </simpleBag>
C: </bag>
C: <lookupEntity
C: registryType="dreg1"
C: entityClass="local"
C: entityName="AUP" />
C: </searchSet>
C: </request>
S: (response packet)
S: 0x20 (header: V=0,RR=response,PD=no,DS=no,PT=xml)
S: 0x03 0xA4 (transaction ID=932)
S: (IRIS XML response)
S: <iris:response xmlns:iris="urn:ietf:params:xml:ns:iris1">
S: <iris:resultSet><iris:answer></iris:answer>
S: <iris:nameNotFound><iris:explanation language="en-US">
S: The name 'AUP' is not found in 'local'.</iris:explanation>
S: </iris:nameNotFound></iris:resultSet></iris:response>
Example 1
Newton Standards Track [Page 15]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
The following example demonstrates an IRIS client requesting domain
availability information for 'milo.example.com'. The server responds
that the domain is assigned and active.
C: (request packet)
C: 0x00 (header: V=0,RR=request,PD=no,DS=no,PT=xml)
C: 0x0B 0xE7 (transaction ID=3047)
C: 0x0F 0xA0 (maximum response size=4000)
C: 0x0B (authority length=11)
C: (authority="example.com")
C: 0x65 0x78 0x61 0x6D 0x70 0x6C 0x65 0x23 0x63 0x6F 0x6D
C: (IRIS XML request)
C: <request xmlns="urn:ietf:params:xml:ns:iris1"
C: xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
C: xsi:schemaLocation="urn:ietf:params:xml:ns:iris1 iris.xsd" >
C: <searchSet>
C: <lookupEntity
C: registryType="urn:ietf:params:xml:ns:dchk1"
C: entityClass="domain-name"
C: entityName="milo.example.com" />
C: </searchSet>
C: </request>
S: (response packet)
S: 0x20 (header: V=0,RR=response,PD=no,DS=no,PT=xml)
S: 0x0B 0xE7 (transaction ID=3047)
S: (IRIS XML response)
S: <iris:response xmlns:iris="urn:ietf:params:xml:ns:iris1">
S: <iris:resultSet><iris:answer><domain
S: authority="example.com" registryType="dchk1"
S: entityClass="domain-name" entityName="tcs-com-1"
S: temporaryReference="true"
S: xmlns="urn:ietf:params:xml:ns:dchk1"><domainName>
S: milo.example.com</domainName><status><assignedAndActive/>
S: </status></domain></iris:answer>
S: </iris:resultSet></iris:response>
Example 2
Newton Standards Track [Page 16]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
The following example demonstrates an IRIS client requesting domain
availability information for felix.example.net, hobbes.example.net,
and daffy.example.net. The client does not support responses
compressed with DEFLATE, and the maximum UDP packet it can safely
receive is 498 octets. The server responds with size information
indicating that it would take 1211 octets to provide an answer.
C: (request packet)
C: 0x00 (header: V=0,RR=request,PD=no,DS=no,PT=xml)
C: 0x7E 0x8A (transaction ID=32394)
C: 0x01 0xF2 (maximum response size=498)
C: 0x0B (authority length=11)
C: (authority="example.net")
C: 0x65 0x78 0x61 0x6D 0x70 0x6C 0x65 0x23 0x6E 0x65 0x74
C: (IRIS XML request)
C: <request xmlns="urn:ietf:params:xml:ns:iris1"
C: xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
C: xsi:schemaLocation="urn:ietf:params:xml:ns:iris1 iris1.xsd">
C: <searchSet>
C: <lookupEntity registryType="dchk1" entityClass="domain-name"
C: entityName="felix.example.net" />
C: </searchSet>
C: <searchSet>
C: <lookupEntity registryType="dchk1" entityClass="domain-name"
C: entityName="hobbes.example.net" />
C: </searchSet>
C: <searchSet>
C: <lookupEntity registryType="dchk1" entityClass="domain-name"
C: entityName="daffy.example.net" />
C: </searchSet>
C: </request>
S: (response packet)
S: 0x22 (header: V=0,RR=response,PD=no,DS=no,PT=si)
S: 0x7E 0x8A (transaction ID=32394)
S: (Size Information XML response)
S: <responseSize xmlns="urn:ietf:params:xml:ns:iris-transport">
S: <octets>1211</octets>
S: </responseSize>
Example 3
Newton Standards Track [Page 17]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
The following example illustrates an IRIS client requesting the
version information from a server, and the server returning the
version information.
C: (request packet)
C: 0x01 (header: V=0,RR=request,PD=no,DS=no,PT=vi)
C: 0x2E 0x9C (transaction ID=11932)
C: 0x01 0xF2 (maximum response size=498)
C: 0x0B (authority length=11)
C: (authority="example.net")
C: 0x65 0x78 0x61 0x6D 0x70 0x6C 0x65 0x23 0x6E 0x65 0x74
S: (response packet)
S: 0x21 (header: V=0,RR=response,PD=no,DS=no,PT=vi)
S: 0x2E 0x9C (transaction ID=11932)
S: (Version Information XML response)
S: <versions xmlns="urn:ietf:params:xml:ns:iris-transport">
S: <transferProtocol protocolId="iris.lwz1">
S: <application protocolId="urn:ietf:params:xml:ns:iris1">
S: <dataModel protocolId="urn:ietf:params:xml:ns:dchk1"/>
S: <dataModel protocolId="urn:ietf:params:xml:ns:dreg1"/>
S: </application>
S: </transferProtocol>
S: </versions>
Example 4
Appendix B. Contributors
Substantive contributions to this document have been provided by the
members of the IETF's CRISP Working Group, especially Milena Caires
and David Blacka.
Author's Address
Andrew L. Newton
VeriSign, Inc.
21345 Ridgetop Circle
Sterling, VA 20166
USA
Phone: +1 703 948 3382
EMail: andy@hxr.us
URI: http://www.verisignlabs.com/
Newton Standards Track [Page 18]
RFC 4993 Lightweight UDP Transfer Protocol for IRIS August 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Newton Standards Track [Page 19]