💾 Archived View for gmi.noulin.net › rfc › rfc3084.gmi captured on 2023-06-16 at 23:30:33. Gemini links have been rewritten to link to archived content

View Raw

More Information

⬅️ Previous capture (2023-01-29)

-=-=-=-=-=-=-

Keywords: COPS-PR, common open policy service, security, quality, provisioning







Network Working Group                                            K. Chan
Request for Comments: 3084                                   J. Seligson
Category: Standards Track                                Nortel Networks
                                                               D. Durham
                                                                   Intel
                                                                  S. Gai
                                                           K. McCloghrie
                                                                   Cisco
                                                               S. Herzog
                                                               IPHighway
                                                           F. Reichmeyer
                                                                     PFN
                                                             R. Yavatkar
                                                                   Intel
                                                                A. Smith
                                                        Allegro Networks
                                                              March 2001


             COPS Usage for Policy Provisioning (COPS-PR)

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

Abstract

   This document describes the use of the Common Open Policy Service
   (COPS) protocol for support of policy provisioning (COPS-PR).  This
   specification is independent of the type of policy being provisioned
   (QoS, Security, etc.) but focuses on the mechanisms and conventions
   used to communicate provisioned information between PDPs and PEPs.
   The protocol extensions described in this document do not make any
   assumptions about the policy data model being communicated, but
   describe the message formats and objects that carry the modeled
   policy data.







Chan, et al.                Standards Track                     [Page 1]

RFC 3084                        COPS-PR                       March 2001


Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC-2119].

Table of Contents

   Glossary........................................................... 3
   1. Introduction.................................................... 3
   1.1. Why COPS for Provisioning?.................................... 5
   1.2. Interaction between the PEP and PDP........................... 5
   2. Policy Information Base (PIB)................................... 6
   2.1. Rules for Modifying and Extending PIBs........................ 7
   2.2. Adding PRCs to, or deprecating from, a PIB.................... 7
   2.2.1. Adding or Deprecating Attributes of a BER Encoded PRC....... 8
   2.3. COPS Operations Supported for a Provisioning Instance......... 8
   3. Message Content................................................. 9
   3.1. Request (REQ)  PEP -> PDP..................................... 9
   3.2. Decision (DEC)  PDP -> PEP....................................10
   3.3. Report State (RPT)  PEP -> PDP................................12
   4. COPS-PR Protocol Objects........................................13
   4.1. Complete Provisioning Instance Identifier (PRID)..............14
   4.2. Prefix PRID (PPRID)...........................................15
   4.3. Encoded Provisioning Instance Data (EPD)......................16
   4.4. Global Provisioning Error Object (GPERR)......................21
   4.5. PRC Class Provisioning Error Object (CPERR)...................22
   4.6. Error PRID Object (ErrorPRID).................................23
   5. COPS-PR Client-Specific Data Formats............................23
   5.1. Named Decision Data...........................................23
   5.2. ClientSI Request Data.........................................24
   5.3. Policy Provisioning Report Data...............................24
   5.3.1. Success and Failure Report-Type Data Format.................24
   5.3.2. Accounting Report-Type Data Format..........................25
   6. Common Operation................................................26
   7. Fault Tolerance.................................................28
   8. Security Considerations.........................................29
   9. IANA Considerations.............................................29
   10. Acknowledgements...............................................30
   11. References.....................................................30
   12. Authors' Addresses.............................................32
   13. Full Copyright Statement.......................................34









Chan, et al.                Standards Track                     [Page 2]

RFC 3084                        COPS-PR                       March 2001


Glossary

      PRC     Provisioning Class.  A type of policy data.
      PRI     Provisioning Instance.  An instance of a PRC.
      PIB     Policy Information Base.  The database of policy
              information.
      PDP     Policy Decision Point.  See [RAP].
      PEP     Policy Enforcement Point.  See [RAP].
      PRID    Provisioning Instance Identifier.  Uniquely identifies an
              instance of a PRC.

1. Introduction

   The IETF Resource Allocation Protocol (RAP) WG has defined the COPS
   (Common Open Policy Service) protocol [COPS] as a scalable protocol
   that allows policy servers (PDPs) to communicate policy decisions to
   network devices (PEPs).  COPS was designed to support multiple types
   of policy clients.

   COPS is a query/response protocol that supports two common models for
   policy control: Outsourcing and Configuration.

   The Outsourcing model addresses the kind of events at the PEP that
   require an instantaneous policy decision (authorization).  In the
   outsourcing scenario, the PEP delegates responsibility to an external
   policy server (PDP) to make decisions on its behalf.  For example, in
   COPS Usage for RSVP [COPRSVP] when a RSVP reservation message
   arrives, the PEP must decide whether to admit or reject the request.
   It can outsource this decision by sending a specific query to its
   PDP, waiting for its decision before admitting the outstanding
   reservation.

   The COPS Configuration model (herein described as the Provisioning
   model), on the other hand, makes no assumptions of such direct 1:1
   correlation between PEP events and PDP decisions.  The PDP may
   proactively provision the PEP reacting to external events (such as
   user input), PEP events, and any combination thereof (N:M
   correlation).  Provisioning may be performed in bulk (e.g., entire
   router QoS configuration) or in portions (e.g., updating a DiffServ
   marking filter).

   Network resources are often provisioned based on relatively static
   SLAs (Service Level Agreements) at network boundaries.  While the
   Outsourcing model is dynamically paced by the PEP in real-time, the
   Provisioning model is paced by the PDP in somewhat flexible timing
   over a wide range of configurable aspects of the PEP.





Chan, et al.                Standards Track                     [Page 3]

RFC 3084                        COPS-PR                       March 2001


       Edge Device               Policy Server
       +--------------+          +-----------+     +-----------+
       |              |          |           |     | External  |
       |              |  COPS    |           |     | Events    |
       |   +-----+    |  REQ()   |  +-----+  |     +---+-------+
       |   |     |----|----------|->|     |  |         |
       |   | PEP |    |          |  | PDP |<-|---------+
       |   |     |<---|----------|--|     |  |
       |   +-----+    |   COPS   |  +-----+  |
       |              |   DEC()  |           |
       +--------------+          +-----------+

                    Figure 1: COPS Provisioning Model

   In COPS-PR, policy requests describe the PEP and its configurable
   parameters (rather than an operational event).  If a change occurs
   in these basic parameters, an updated request is sent.  Hence,
   requests are issued quite infrequently.  Decisions are not
   necessarily mapped directly to requests, and are issued mostly
   when the PDP responds to external events or PDP events (policy/SLA
   updates).

   This document describes the use of the COPS protocol [COPS] for
   support of policy provisioning.  This specification is independent
   of the type of policy being provisioned (QoS, Security, etc.).
   Rather, it focuses on the mechanisms and conventions used to
   communicate provisioned information between PDPs and PEPs.  The
   data model assumed in this document is based on the concept of
   Policy Information Bases (PIBs) that define the policy data.  There
   may be one or more PIBs for given area of policy and different
   areas of policy may have different sets of PIBs.

   In order to support a model that includes multiple PDPs
   controlling non-overlapping areas of policy on a single PEP, the
   client-type specified by the PEP to the PDP is unique for the area
   of policy being managed.  A single client-type for a given area of
   policy (e.g., QoS) will be used for all PIBs that exist in that
   area.  The client should treat all the COPS-PR client-types it
   supports as non-overlapping and independent namespaces where
   instances MUST NOT be shared.

   The examples used in this document are biased toward QoS Policy
   Provisioning in a Differentiated Services (DiffServ) environment.
   However, COPS-PR can be used for other types of provisioning
   policies under the same framework.






Chan, et al.                Standards Track                     [Page 4]

RFC 3084                        COPS-PR                       March 2001


1.1. Why COPS for Provisioning?

   COPS-PR has been designed within a framework that is optimized for
   efficiently provisioning policies across devices, based on the
   requirements defined in [RAP].  First, COPS-PR allows for efficient
   transport of attributes, large atomic transactions of data, and
   efficient and flexible error reporting.  Second, as it has a single
   connection between the policy client and server per area of policy
   control identified by a COPS Client-Type, it guarantees only one
   server updates a particular policy configuration at any given
   time.  Such a policy configuration is effectively locked, even from
   local console configuration, while the PEP is connected to a PDP
   via COPS.  COPS uses reliable TCP transport and, thus, uses a state
   sharing/synchronization mechanism and exchanges differential
   updates only.  If either the server or client are rebooted (or
   restarted) the other would know about it quickly.  Last, it is
   defined as a real-time event-driven communications mechanism,
   never requiring polling between the PEP and PDP.

1.2. Interaction between the PEP and PDP

   When a device boots, it opens a COPS connection to its Primary
   PDP.  When the connection is established, the PEP sends information
   about itself to the PDP in the form of a configuration request.
   This information includes client specific information (e.g.,
   hardware type, software release, configuration information).
   During this phase the client may also specify the maximum COPS-PR
   message size supported.

   In response, the PDP downloads all provisioned policies that are
   currently relevant to that device.  On receiving the provisioned
   policies, the device maps them into its local QoS mechanisms, and
   installs them.  If conditions change at the PDP such that the PDP
   detects that changes are required in the provisioned policies
   currently in effect, then the PDP sends the changes (installs,
   updates, and/or deletes) in policy to the PEP, and the PEP updates
   its local configuration appropriately.

   If, subsequently, the configuration of the device changes (board
   removed, board added, new software installed, etc.) in ways not
   covered by policies already known to the PEP, then the PEP
   asynchronously sends this unsolicited new information to the PDP
   in an updated configuration request.  On receiving this new
   information, the PDP sends to the PEP any additional provisioned
   policies now needed by the PEP, or removes those policies that are
   no longer required.





Chan, et al.                Standards Track                     [Page 5]

RFC 3084                        COPS-PR                       March 2001


2. Policy Information Base (PIB)

   The data carried by COPS-PR is a set of policy data.  The protocol
   assumes a named data structure, known as a Policy Information Base
   (PIB), to identify the type and purpose of unsolicited policy
   information that is "pushed" from the PDP to the PEP for
   provisioning policy or sent to the PDP from the PEP as a
   notification.  The PIB name space is common to both the PEP and the
   PDP and data instances within this space are unique within the
   scope of a given Client-Type and Request-State per TCP connection
   between a PEP and PDP.  Note that given a device might implement
   multiple COPS Client-Types, a unique instance space is to be
   provided for each separate Client-Type.  There is no sharing of
   instance data across the Client-Types implemented by a PEP, even
   if the classes being instantiated are of the same type and share
   the same instance identifier.

   The PIB can be described as a conceptual tree namespace where the
   branches of the tree represent structures of data or Provisioning
   Classes (PRCs), while the leaves represent various instantiations
   of Provisioning Instances (PRIs).  There may be multiple data
   instances (PRIs) for any given data structure (PRC).  For example,
   if one wanted to install multiple access control filters, the PRC
   might represent a generic access control filter type and each PRI
   might represent an individual access control filter to be applied.
   The tree might be represented as follows:

             -------+-------+----------+---PRC--+--PRI
                    |       |          |        +--PRI
                    |       |          |
                    |       |          +---PRC-----PRI
                    |       |
                    |       +---PRC--+--PRI
                    |                +--PRI
                    |                +--PRI
                    |                +--PRI
                    |                +--PRI
                    |
                    +---PRC---PRI

                          Figure 2: The PIB Tree

   Instances of the policy classes (PRIs) are each identified by a
   Provisioning Instance Identifier (PRID).  A PRID is a name, carried
   in a COPS <Named ClientSI> or <Named Decision Data> object, which
   identifies a particular instance of a class.





Chan, et al.                Standards Track                     [Page 6]

RFC 3084                        COPS-PR                       March 2001


2.1. Rules for Modifying and Extending PIBs

   As experience is gained with policy based management, and as new
   requirements arise, it will be necessary to make changes to PIBs.
   Changes to an existing PIB can be made in several ways.

    (1) Additional PRCs can be added to a PIB or an existing one
        deprecated.

    (2) Attributes can be added to, or deprecated from, an existing
        PRC.

    (3) An existing PRC can be extended or augmented with a new PRC
        defined in another (perhaps enterprise specific) PIB.

   The rules for each of these extension mechanisms is described in this
   sub-section.  All of these mechanisms for modifying a PIB allow for
   interoperability between PDPs and PEPs even when one party is using a
   new version of the PIB while the other is using an old version.

   Note that the SPPI [SPPI] provides the authoritative rules for
   updating BER encoded PIBs.  It is the purpose of the following
   section to explain how such changes affect senders and receivers of
   COPS messages.

2.2. Adding PRCs to, or deprecating from, a PIB

   A published PIB can be extended with new PRCs by simply revising the
   document and adding additional PRCs.  These additional PRCs are
   easily identified with new PRIDs under the module's PRID Prefix.

   In the event that a PEP implementing the new PIB is being configured
   by a PDP implementing the old PIB, the PEP will simply not receive
   any instances of the new PRC.  In the event that the PEP is
   implementing the old PIB and the PDP the new one, the PEP may receive
   PRIs for the new PRC.  Under such conditions, the PEP MUST return an
   error to the PDP, and rollback to its previous (good) state.

   Similarly, existing PRCs can be deprecated from a PIB.  In this case,
   the PEP ignores any PRIs sent to it by a PDP implementing the old
   (non-deprecated) version of the PIB.  A PDP implementing the new
   version of the PIB simply does not send any instances of the
   deprecated class.








Chan, et al.                Standards Track                     [Page 7]

RFC 3084                        COPS-PR                       March 2001


2.2.1. Adding or Deprecating Attributes of a BER Encoded PRC

   A PIB can be modified to deprecate existing attributes of a PRC or
   add new ones.

   When deprecating the attributes of a PRC, it must be remembered that,
   with the COPS-PR protocol, the attributes of the PRC are identified
   by their order in the sequence rather than an explicit label (or
   attribute OID).  Consequently, an ASN.1 value MUST be sent even for
   deprecated attributes so that a PDP and PEP implementing different
   versions of the PIB are inter-operable.

   For a deprecated attribute, if the PDP is using a BER encoded PIB,
   the PDP MUST send either an ASN.1 value of the correct type, or it
   may send an ASN.1 NULL value.  A PEP that receives an ASN.1 NULL for
   an attribute that is not deprecated SHOULD substitute a default
   value.  If it has no default value to substitute it MUST return an
   error to the PDP.

   When adding new attributes to a PIB, these new attributes must be
   added in sequence after the existing ones.  A PEP that receives a PRI
   with more attributes than it is expecting MUST ignore the additional
   attributes and send a warning back to the PDP.

   A PEP that receives a PRI with fewer attributes than it is expecting
   SHOULD assume default values for the missing attributes. It MAY send
   a warning back to the PDP.  If the missing attributes are required
   and there is no suitable default, the PEP MUST send an error back to
   the PDP.  In all cases the missing attributes are assumed to
   correspond to the last attributes of the PRC.

2.3. COPS Operations Supported for a Provisioning Instance

   A Provisioning Instance (PRI) typically contains a value for each
   attribute defined for the PRC of which it is an instance and is
   identified uniquely, within the scope of a given COPS Client-Type and
   Request-State on a PEP, by a Provisioning Instance Identifier (PRID).
   The following COPS operations are supported on a PRI:

   o Install - This operation creates or updates a named instance of a
     PRC.  It includes two parameters: a PRID object to name the PRI and
     an Encoded Provisioning Instance Data (EPD) object with the
     new/updated values.  The PRID value MUST uniquely identify a single
     PRI (i.e., PRID prefix or PRC values are illegal).  Updates to an
     existing PRI are achieved by simply reinstalling the same PRID with
     the updated EPD data.





Chan, et al.                Standards Track                     [Page 8]

RFC 3084                        COPS-PR                       March 2001


   o Remove - This operation is used to delete an instance of a PRC. It
     includes one parameter, a PRID object, which names either the
     individual PRI to be deleted or a PRID prefix naming one or more
     complete classes of PRIs.  Prefix-based deletion supports efficient
     bulk policy removal.  The removal of an unknown/non-existent PRID
     SHOULD result in a warning to the PDP (no error).

3. Message Content

   The COPS protocol provides for different COPS clients to define their
   own "named", i.e., client-specific, information for various messages.
   This section describes the messages exchanged between a COPS server
   (PDP) and COPS Policy Provisioning clients (PEP) that carry client-
   specific data objects.  All the COPS messages used by COPS-PR conform
   to the message specifications defined in the COPS base protocol
   [COPS].

   Note: The use of the '*' character represented throughout this
   document is consistent with the ABNF [RFC2234] and means 0 or more of
   the following entities.

3.1. Request (REQ)  PEP -> PDP

   The REQ message is sent by policy provisioning clients to issue a
   'configuration request' to the PDP as specified in the COPS Context
   Object.  The Client Handle associated with the REQ message originated
   by a provisioning client MUST be unique for that client.  The Client
   Handle is used to identify a specific request state.  Thus, one
   client can potentially open several configuration request states,
   each uniquely identified by its handle.  Different request states are
   used to isolate similarly named configuration information into non-
   overlapping contexts (or logically isolated namespaces).  Thus, an
   instance of named information is unique relative to a particular
   client-type and is unique relative to a particular request state for
   that client-type, even if the information was similarly identified in
   other request states (i.e., uses the same PRID).  Thus, the Client
   Handle is also part of the instance identification of the
   communicated configuration information.

   The configuration request message serves as a request from the PEP to
   the PDP for provisioning policy data that the PDP may have for the
   PEP, such as access control lists, etc.  This includes policy the PDP
   may have at the time the REQ is received as well as any future policy
   data or updates to this data.

   The configuration request message should include provisioning client
   information to provide the PDP with client-specific configuration or
   capability information about the PEP.  The information provided by



Chan, et al.                Standards Track                     [Page 9]

RFC 3084                        COPS-PR                       March 2001


   the PEP should include client resources (e.g., queuing capabilities)
   and default policy configuration (e.g., default role combinations)
   information as well as incarnation data on existing policy.  This
   information typically does not include all the information previously
   installed by a PDP but rather should include checksums or shortened
   references to previously installed information for synchronization
   purposes.  This information from the client assists the server in
   deciding what types of policy the PEP can install and enforce.  The
   format of the information encapsulated in one or more of the COPS
   Named ClientSI objects is described in section 5.  Note that the
   configuration request message(s) is generated and sent to the PDP in
   response to the receipt of a Synchronize State Request (SSQ) message
   from the PDP.  Likewise, an updated configuration request message
   (using the same Client Handle value as the original request now being
   updated) may also be generated by the PEP and sent to the PDP at any
   time due to local modifications of the PEP's internal state.  In this
   way, the PDP will be synchronized with the PEP's relevant internal
   state at all times.

   The policy information supplied by the PDP MUST be consistent with
   the named decision data defined for the policy provisioning client.
   The PDP responds to the configuration request with a DEC message
   containing any available provisioning policy data.

   The REQ message has the following format:

               <Request> ::= <Common Header>
                              <Client Handle>
                              <Context = config request>
                              *(<Named ClientSI>)
                              [<Integrity>]

   Note that the COPS objects IN-Int, OUT-Int and LPDPDecisions are not
   included in a COPS-PR Request.

3.2. Decision (DEC)  PDP -> PEP

   The DEC message is sent from the PDP to a policy provisioning client
   in response to the REQ message received from the PEP.  The Client
   Handle MUST be the same Handle that was received in the corresponding
   REQ message.

   The DEC message is sent as an immediate response to a configuration
   request with the solicited message flag set in the COPS message
   header.  Subsequent DEC messages may also be sent at any time after
   the original DEC message to supply the PEP with additional/updated
   policy information without the solicited message flag set in the COPS
   message header (as they are unsolicited decisions).



Chan, et al.                Standards Track                    [Page 10]

RFC 3084                        COPS-PR                       March 2001


   Each DEC message may contain multiple decisions.  This means a single
   message can install some policies and delete others.  In general a
   single COPS-PR DEC message MUST contain any required remove decisions
   first, followed by any required install decisions.  This is used to
   solve a precedence issue, not a timing issue: the remove decision
   deletes what it specifies, except those items that are installed in
   the same message.

   The DEC message can also be used by the PDP to command the PEP to
   open a new Request State or Delete an existing Request-State as
   identified by the Client-Handle.  To accomplish this, COPS-PR defines
   a new flag for the COPS Decision Flags object.  The flag 0x02 is to
   be used by COPS-PR client-types and is hereafter referred to as the
   "Request-State" flag.  An Install decision (Decision Flags: Command-
   Code=Install) with the Request-State flag set in the COPS Decision
   Flags object will cause the PEP to issue a new Request with a new
   Client Handle or else specify the appropriate error in a COPS Report
   message.  A Remove decision (Decision Flags: Command-Code=Remove)
   with the Request-State flag set in the COPS Decision Flags object
   will cause the PEP to send a COPS Delete Request State (DRQ) message
   for the Request-State identified by the Client Handle in the DEC
   message.  Whenever the Request-State flag is set in the COPS Decision
   Flags object in the DEC message, no COPS Named Decision Data object
   can be included in the corresponding decision (as it serves no
   purpose for this decision flag).  Note that only one decision with
   the Request-State flag can be present per DEC message, and, if
   present, this MUST be the only decision in that message.  As
   described below, the PEP MUST respond to each and every DEC with a
   corresponding solicited RPT.

   A COPS-PR DEC message MUST be treated as a single "transaction",
   i.e., either all the decisions in a DEC message succeed or they all
   fail.  If they fail, the PEP will rollback to its previous good
   state, which is the last successful DEC transaction, if any.  This
   allows the PDP to delete some policies only if other policies can be
   installed in their place.  The DEC message has the following format:

   <Decision Message> ::= <Common Header>
                          <Client Handle>
                          *(<Decision>) | <Error>
                          [<Integrity>]

   <Decision> ::= <Context>
                  <Decision: Flags>
                  [<Named Decision Data: Provisioning >]






Chan, et al.                Standards Track                    [Page 11]

RFC 3084                        COPS-PR                       March 2001


   Note that the Named Decision Data (Provisioning) object is included
   in a COPS-PR Decision when it is an Install or Remove decision with
   no Decision Flags set.  Other types of COPS decision data objects
   (e.g., Stateless, Replacement) are not supported by COPS-PR client-
   types.  The Named Decision Data object MUST NOT be included in the
   decision if the Decision Flags object Command-Code is NULL (meaning
   there is no configuration information to install at this time) or if
   the Request-State flag is set in the Decision Flags object.

   For each decision in the DEC message, the PEP performs the operation
   specified in the Command-Code and Flags field in the Decision Flags
   object on the Named Decision Data.  For the policy provisioning
   clients, the format for this data is defined in the context of the
   Policy Information Base (see section 5).  In response to a DEC
   message, the policy provisioning client MUST send a RPT message, with
   the solicited message flag set, back to the PDP to inform the PDP of
   the action taken.

3.3. Report State (RPT)  PEP -> PDP

   The RPT message is sent from the policy provisioning clients to the
   PDP to report accounting information associated with the provisioned
   policy, or to notify the PDP of changes in the PEP (Report-Type = '
   Accounting') related to the provisioning client.

   RPT is also used as a mechanism to inform the PDP about the action
   taken at the PEP in response to a DEC message.  For example, in
   response to an 'Install' decision, the PEP informs the PDP if the
   policy data is installed (Report-Type = 'Success') or not (Report-
   Type = 'Failure').  Reports that are in response to a DEC message
   MUST set the solicited message flag in their COPS message header.
   Each solicited RTP MUST be sent for its corresponding DEC in the
   order the DEC messages were received.  In case of a solicited
   failure, the PEP is expected to rollback to its previous (good) state
   as if the erroneous DEC transaction did not occur.  The PEP MUST
   always respond to a DEC with a solicited RPT even in response to a
   NULL DEC, in which case the Report-Type will be 'Success'.

   Reports can also be unsolicited and all unsolicited Reports MUST NOT
   set the solicited message flag in their COPS message header. Examples
   of unsolicited reports include 'Accounting' Report-Types, which were
   not triggered by a specific DEC messages, or 'Failure' Report-Types,
   which indicate a failure in a previously successfully installed
   configuration (note that, in the case of such unsolicited failures,
   the PEP cannot rollback to a previous "good" state as it becomes
   ambiguous under these asynchronous conditions what the correct state
   might be).




Chan, et al.                Standards Track                    [Page 12]

RFC 3084                        COPS-PR                       March 2001


   The RPT message may contain provisioning client information such as
   accounting parameters or errors/warnings related to a decision. The
   data format for this information is defined in the context of the
   policy information base (see section 5).  The RPT message has the
   following format:

               <Report State> ::= <Common Header>
                                  <Client Handle>
                                  <Report Type>
                                  *(<Named ClientSI>)
                                  [<Integrity>]

4. COPS-PR Protocol Objects

   The COPS Policy Provisioning clients encapsulate several new objects
   within the existing COPS Named Client-specific information object and
   Named Decision Data object.  This section defines the format of these
   new objects.

   COPS-PR classifies policy data according to "bindings", where a
   binding consists of a Provisioning Instance Identifier and the
   Provisioning Instance data, encoded within the context of the
   provisioning policy information base (see section 5).

   The format for these new objects is as follows:

           0                1               2                 3
   +---------------+---------------+---------------+---------------+
   |             Length            |     S-Num     |     S-Type    |
   +---------------+---------------+---------------+---------------+
   |                   32 bit unsigned integer                     |
   +---------------+---------------+---------------+---------------+

   S-Num and S-Type are similar to the C-Num and C-Type used in the base
   COPS objects.  The difference is that S-Num and S-Type are used only
   for COPS-PR clients and are encapsulated within the existing COPS
   Named ClientSI or Named Decision Data objects.  The S-Num identifies
   the general purpose of the object, and the S-Type describes the
   specific encoding used for the object.  All the object descriptions
   and examples in this document use the Basic Encoding Rules as the
   encoding type (S-Type = 1).  Additional encodings can be defined for
   the remaining S-Types in the future (for example, an additional S-
   Type could be used to carry XML string based encodings [XML] as an
   EPD of PRI instance data, where URNs identify PRCs [URN] and
   XPointers would be used for PRIDs).






Chan, et al.                Standards Track                    [Page 13]

RFC 3084                        COPS-PR                       March 2001


   Length is a two-octet value that describes the number of octets
   (including the header) that compose the object.  If the length in
   octets does not fall on a 32-bit word boundary, padding MUST be added
   to the end of the object so that it is aligned to the next 32-bit
   boundary before the object can be sent on the wire.  On the receiving
   side, a subsequent object boundary can be found by simply rounding up
   the stated object length of the current object to the next 32-bit
   boundary.  The values for the padding MUST be all zeros.

4.1. Complete Provisioning Instance Identifier (PRID)

   S-Num = 1 (Complete PRID), S-Type = 1 (BER), Length = variable.

   This object is used to carry the identifier, or PRID, of a
   Provisioning Instance.  The identifier is encoded following the rules
   that have been defined for encoding SNMP Object Identifier (OID)
   values.  Specifically, PRID values are encoded using the
   Type/Length/Value (TLV) format and initial sub-identifier packing
   that is specified by the binary encoding rules [BER] used for Object
   Identifiers in an SNMP PDU.

           0                1               2                 3
   +---------------+---------------+---------------+---------------+
   |              Length           | S-Num = PRID  | S-Type = BER  |
   +---------------+---------------+---------------+---------------+
   |                     Instance Identifier                       |
   +---------------+---------------+---------------+---------------+

   For example, a (fictitious) PRID equal to 1.3.6.1.2.2.8.1 would be
   encoded as follows (values in hex):

         06 07 2B 06 01 02 02 08 01

   The entire PRID object would be encoded as follows:

         00 0D                        - Length
         01                           - S-Num
         01                           - S-Type (Complete PRID)
         06 07 2B 06 01 02 02 08 01   - Encoded PRID
         00 00 00                     - Padding

   NOTE: When encoding an xxxTable's xxxEntry Object-Type as defined by
   the SMI [V2SMI] and SPPI [SPPI], the OID will contain all the sub-
   identifiers up to and including the xxxEntry OID but not the columnar
   identifiers for the attributes within the xxxEntry's SEQUENCE.  The
   last (suffix) identifier is the INDEX of an instance of an entire





Chan, et al.                Standards Track                    [Page 14]

RFC 3084                        COPS-PR                       March 2001


   xxxEntry including its SEQUENCE of attributes encoded in the EPD
   (defined below).  This constitutes an instance (PRI) of a class (PRC)
   in terms of the SMI.

   A PRID for a scalar (non-columnar) value's OID is encoded directly as
   the PRC where the instance identifier suffix is always zero as there
   will be only one instance of a scalar value.  The EPD will then be
   used to convey the scalar value.

4.2. Prefix PRID (PPRID)

   Certain operations, such as decision removal, can be optimized by
   specifying a PRID prefix with the intent that the requested operation
   be applied to all PRIs matching the prefix (for example, all
   instances of the same PRC).  PRID prefix objects MUST only be used in
   the COPS protocol <Remove Decision> operation where it may be more
   optimal to perform bulk decision removal using class prefixes instead
   of a sequence of individual <Remove Decision> operations.  Other COPS
   operations, e.g., <Install Decision> operations always require
   individual PRID specification.

   S-Num = 2 (Prefix PRID), S-Type = 1 (BER), Length = variable.

              0                1               2                 3
    +---------------+---------------+---------------+---------------+
    |              Length           | S-Num = PPRID | S-Type = BER  |
    +---------------+---------------+---------------+---------------+
    ...                                                           ...
    |                          Prefix PRID                          |
    ...                                                           ...
    +---------------+---------------+---------------+---------------+

   Continuing with the previous example, a prefix PRID that is equal to
   1.3.6.1.2.2 would be encoded as follows (values in hex):

         06 05 2B 06 01 02 02

      The entire PPRID object would be encoded as follows:

         00 0B                        - Length
         02                           - S-Num = Prefix PRID
         01                           - S-Type = BER
         06 05 2B 06 01 02 02         - Encoded Prefix PRID
         00                           - Padding







Chan, et al.                Standards Track                    [Page 15]

RFC 3084                        COPS-PR                       March 2001


4.3. Encoded Provisioning Instance Data (EPD)

   S-Num = 3 (EPD), S-Type = 1 (BER), Length = variable.

   This object is used to carry the encoded value of a Provisioning
   Instance.  The PRI value, which contains all of the individual values
   of the attributes that comprise the class (which corresponds to the
   SMI's xxxEntry Object-Type defining the SEQUENCE of attributes
   comprising a table [V2SMI][SPPI]), is encoded as a series of TLV
   sub-components.  Each sub-component represents the value of a single
   attribute and is encoded following the BER.  Note that the ordering
   of non-scalar (multiple) attributes within the EPD is dictated by
   their respective columnar OID suffix when defined in [V2SMI].  Thus,
   the attribute with the smallest columnar OID suffix will appear first
   and the attribute with the highest number columnar OID suffix will be
   last.

           0                1               2                 3
   +---------------+---------------+---------------+---------------+
   |             Length            | S-Num = EPD   | S-Type = BER  |
   +---------------+---------------+---------------+---------------+
   |                     BER Encoded PRI Value                     |
   +---------------+---------------+---------------+---------------+

   As an example, a fictional definition of an IPv4 packet filter class
   could be described using the SMI as follows:

   ipv4FilterIpFilter OBJECT IDENTIFIER ::= { someExampleOID 1 }

   -- The IP Filter Table

   ipv4FilterTable OBJECT-TYPE
       SYNTAX         SEQUENCE OF Ipv4FilterEntry
       MAX-ACCESS     not-accessible
       STATUS         current
       DESCRIPTION
           "Filter definitions.  A packet has to match all fields in
           a filter.  Wildcards may be specified for those fields
           that are not relevant."

       ::= { ipv4FilterIpFilter 1 }

   ipv4FilterEntry OBJECT-TYPE
       SYNTAX         Ipv4FilterEntry
       MAX-ACCESS     not-accessible
       STATUS         current
       DESCRIPTION
           "An instance of the filter class."



Chan, et al.                Standards Track                    [Page 16]

RFC 3084                        COPS-PR                       March 2001



       INDEX { ipv4FilterIndex }

       ::= { ipv4FilterTable 1 }

   Ipv4FilterEntry ::= SEQUENCE {
           ipv4FilterIndex        Unsigned32,
           ipv4FilterDstAddr      IpAddress,
           ipv4FilterDstAddrMask  IpAddress,
           ipv4FilterSrcAddr      IpAddress,
           ipv4FilterSrcAddrMask  IpAddress,
           ipv4FilterDscp         Integer32,
           ipv4FilterProtocol     Integer32,
           ipv4FilterDstL4PortMin Integer32,
           ipv4FilterDstL4PortMax Integer32,
           ipv4FilterSrcL4PortMin Integer32,
           ipv4FilterSrcL4PortMax Integer32,
           ipv4FilterPermit       TruthValue
   }

   ipv4FilterIndex OBJECT-TYPE
       SYNTAX         Unsigned32
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
        "An integer index to uniquely identify this filter among all
         the filters."

       ::= { ipv4FilterEntry 1 }

   ipv4FilterDstAddr OBJECT-TYPE

       SYNTAX         IpAddress
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
        "The IP address to match against the packet's destination IP
        address."

       ::= { ipv4FilterEntry 2 }

   ipv4FilterDstAddrMask OBJECT-TYPE
       SYNTAX         IpAddress
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
        "A mask for the matching of the destination IP address.
        A zero bit in the mask means that the corresponding bit in



Chan, et al.                Standards Track                    [Page 17]

RFC 3084                        COPS-PR                       March 2001


        the address always matches."

       ::= { ipv4FilterEntry 3 }

   ipv4FilterSrcAddr OBJECT-TYPE
       SYNTAX         IpAddress
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
           "The IP address to match against the packet's source IP
           address."

       ::= { ipv4FilterEntry 4 }

   ipv4FilterSrcAddrMask OBJECT-TYPE
       SYNTAX         IpAddress
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
           "A mask for the matching of the source IP address."

       ::= { ipv4FilterEntry 5 }

   ipv4FilterDscp OBJECT-TYPE
       SYNTAX         Integer32 (-1 | 0..63)
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
           "The value that the DSCP in the packet can have and
           match.  A value of -1 indicates that a specific
           DSCP value has not been defined and thus all DSCP values
           are considered a match."

       ::= { ipv4FilterEntry 6 }

   ipv4FilterProtocol OBJECT-TYPE
       SYNTAX         Integer32 (0..255)
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
           "The IP protocol to match against the packet's protocol.
           A value of zero means match all."

       ::= { ipv4FilterEntry 7 }

   ipv4FilterDstL4PortMin OBJECT-TYPE
       SYNTAX         Integer32 (0..65535)
       MAX-ACCESS     read-write



Chan, et al.                Standards Track                    [Page 18]

RFC 3084                        COPS-PR                       March 2001


       STATUS         current
       DESCRIPTION
           "The minimum value that the packet's layer 4 destination
           port number can have and match this filter."

       ::= { ipv4FilterEntry 8 }

   ipv4FilterDstL4PortMax OBJECT-TYPE
       SYNTAX         Integer32 (0..65535)
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
           "The maximum value that the packet's layer 4 destination
           port number can have and match this filter."

       ::= { ipv4FilterEntry 9 }

   ipv4FilterSrcL4PortMin OBJECT-TYPE
       SYNTAX         Integer32 (0..65535)
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
           "The minimum value that the packet's layer 4 source port
           number can have and match this filter."

       ::= { ipv4FilterEntry 10 }

   ipv4FilterSrcL4PortMax OBJECT-TYPE
       SYNTAX         Integer32 (0..65535)
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
           "The maximum value that the packet's layer 4 source port
           number can have and match this filter."

       ::= { ipv4FilterEntry 11 }

   ipv4FilterPermit OBJECT-TYPE
       SYNTAX         TruthValue
       MAX-ACCESS     read-write
       STATUS         current
       DESCRIPTION
           "If false, the evaluation is negated.  That is, a
           valid match will be evaluated as not a match and vice
           versa."

       ::= { ipv4FilterEntry 12 }




Chan, et al.                Standards Track                    [Page 19]

RFC 3084                        COPS-PR                       March 2001


   A fictional instance of the filter class defined above might then
   be encoded as follows:

   02 01 08          :ipv4FilterIndex/Unsigned32/Value = 8
   40 04 C0 39 01 05 :ipv4FilterDstAddr/IpAddress/Value = 192.57.1.5
   40 04 FF FF FF FF :ipv4FilterDstMask/IpAddress/Value=255.255.255.255
   40 04 00 00 00 00 :ipv4FilterSrcAddr/IpAddress/Value = 0.0.0.0
   40 04 00 00 00 00 :ipv4FilterSrcMask/IpAddress/Value = 0.0.0.0
   02 01 FF          :ipv4FilterDscp/Integer32/Value = -1 (not used)
   02 01 06          :ipv4FilterProtocol/Integer32/Value = 6 (TCP)
   05 00             :ipv4FilterDstL4PortMin/NULL/not supported
   05 00             :ipv4FilterDstL4PortMax/NULL/not supported
   05 00             :ipv4FilterSrcL4PortMin/NULL/not supported
   05 00             :ipv4FilterSrcL4PortMax/NULL/not supported
   02 01 01          :ipv4FilterPermit/TruthValue/Value = 1 (true)

   The entire EPD object for this instance would then be encoded as
   follows:

   00 30                        - Length
   03                           - S-Num = EPD
   01                           - S-Type = BER
   02 01 08                     - ipv4FilterIndex
   40 04 C0 39 01 05            - ipv4FilterDstAddr
   40 04 FF FF FF FF            - ipv4FilterDstMask
   40 04 00 00 00 00            - ipv4FilterSrcAddr
   40 04 00 00 00 00            - ipv4FilterSrcMask
   02 01 FF                     - ipv4FilterDscp
   02 01 06                     - ipv4FilterProtocol
   05 00                        - ipv4FilterDstL4PortMin
   05 00                        - ipv4FilterDstL4PortMax
   05 00                        - ipv4FilterSrcL4PortMin
   05 00                        - ipv4FilterSrcL4PortMax
   02 01 01                     - ipv4FilterPermit

   Note that attributes not supported within a class are still returned
   in the EPD for a PRI.  By convention, a NULL value is returned for
   attributes that are not supported.  In the previous example, source
   and destination port number attributes are not supported.












Chan, et al.                Standards Track                    [Page 20]

RFC 3084                        COPS-PR                       March 2001


4.4. Global Provisioning Error Object (GPERR)

   S-Num = 4 (GPERR), S-Type = 1 (for BER), Length = 8.

            0                1               2                 3
   +---------------+---------------+---------------+---------------+
   |              Length           | S-Num = GPERR | S-Type = BER  |
   +---------------+---------------+---------------+---------------+
   |           Error-Code          |       Error Sub-code          |
   +---------------+---------------+---------------+---------------+

   The global provisioning error object has the same format as the Error
   object in COPS [COPS], except with C-Num and C-Type replaced by the
   S-Num and S-Type values shown.  The global provision error object is
   used to communicate general errors that do not map to a specific PRC.

   The following global error codes are defined:

     availMemLow(1)
     availMemExhausted(2)
     unknownASN.1Tag(3)     - The erroneous tag type SHOULD be
                              specified in the Error Sub-Code field.
     maxMsgSizeExceeded(4)  - COPS message (transaction) was too big.
     unknownError(5)
     maxRequestStatesOpen(6)- No more Request-States can be created
                              by the PEP (in response to a DEC
                              message attempting to open a new
                              Request-State).
     invalidASN.1Length(7)  - An ASN.1 object length was incorrect.
     invalidObjectPad(8)    - Object was not properly padded.
     unknownPIBData(9)      - Some of the data supplied by the PDP is
                              unknown/unsupported by the PEP (but
                              otherwise formatted correctly).  PRC
                              specific error codes are to be used to
                              provide more information.
     unknownCOPSPRObject(10)- Sub-code (octet 2) contains unknown
                              object's S-Num and (octet 3) contains
                              unknown object's S-Type.
     malformedDecision(11)  - Decision could not be parsed.












Chan, et al.                Standards Track                    [Page 21]

RFC 3084                        COPS-PR                       March 2001


4.5. PRC Class Provisioning Error Object (CPERR)

   S-Num = 5 (CPERR), S-Type = 1 (for BER), Length = 8.

            0                1               2                 3
   +---------------+---------------+---------------+---------------+
   |              Length           | S-Num = CPERR | S-Type = BER  |
   +---------------+---------------+---------------+---------------+
   |           Error-Code          |       Error Sub-code          |
   +---------------+---------------+---------------+---------------+

   The class-specific provisioning error object has the same format as
   the Error object in COPS [COPS], except with C-Num and C-Type
   replaced by the S-Num and S-Type values shown.  The class-specific
   error object is used to communicate errors relating to specific PRCs
   and MUST have an associated Error PRID Object.

   The following Generic Class-Specific errors are defined:

     priSpaceExhausted(1) -     no more instances may currently be
                                installed in the given class.
     priInstanceInvalid(2) -    the specified class instance is
                                currently invalid prohibiting
                                installation or removal.
     attrValueInvalid(3) -      the specified value for identified
                                attribute is illegal.
     attrValueSupLimited(4) -   the specified value for the identified
                                attribute is legal but not currently
                                supported by the device.
     attrEnumSupLimited(5) -    the specified enumeration for the
                                identified attribute is legal but not
                                currently supported by the device.
     attrMaxLengthExceeded(6) - the overall length of the specified
                                value for the identified attribute
                                exceeds device limitations.
     attrReferenceUnknown(7) -  the class instance specified by the
                                policy instance identifier does not
                                exist.
     priNotifyOnly(8) -         the class is currently only supported
                                for use by request or report messages
                                prohibiting decision installation.
     unknownPrc(9) -            attempt to install a PRI of a class not
                                supported by PEP.
     tooFewAttrs(10) -          recvd PRI has fewer attributes than
                                required.
     invalidAttrType(11) -      recvd PRI has an attribute of the wrong
                                type.




Chan, et al.                Standards Track                    [Page 22]

RFC 3084                        COPS-PR                       March 2001


     deletedInRef(12)  -        deleted PRI is still referenced by
                                other (non) deleted PRIs
     priSpecificError(13) -     the Error Sub-code field contains the
                                PRC specific error code

     Where appropriate (errors 3, 4, 5, 6, 7 above) the error sub-code
      SHOULD identify the OID sub-identifier of the attribute
      associated with the error.

4.6. Error PRID Object (ErrorPRID)

   S-Num = 6 (ErrorPRID), S-Type = 1 (BER), Length = variable.

   This object is used to carry the identifier, or PRID, of a
   Provisioning Instance that caused an installation error or could not
   be installed or removed.  The identifier is encoded and formatted
   exactly as in the PRID object as described in section 4.1.

5. COPS-PR Client-Specific Data Formats

   This section describes the format of the named client specific
   information for the COPS policy provisioning client.  ClientSI
   formats are defined for Decision message's Named Decision Data
   object, the Request message's Named ClientSI object and Report
   message's Named ClientSI object.  The actual content of the data is
   defined by the policy information base for a specific provisioning
   client-type (see below).

5.1. Named Decision Data

   The formats encapsulated by the Named Decision Data object for the
   policy provisioning client-types depends on the type of decision.
   Install and Remove are the two types of decisions that dictate the
   internal format of the COPS Named Decision Data object and require
   its presence.  Install and Remove refer to the 'Install' and 'Remove'
   Command-Code, respectively, specified in the COPS Decision Flags
   Object when no Decision Flags are set.  The data, in general, is
   composed of one or more bindings.  Each binding associates a PRID
   object and a EPD object.  The PRID object is always present in both
   install and remove decisions, the EPD object MUST be present in the
   case of an install decision and MUST NOT be present in the case of a
   remove decision.









Chan, et al.                Standards Track                    [Page 23]

RFC 3084                        COPS-PR                       March 2001


   The format for this data is encapsulated within the COPS Named
   Decision Data object as follows:
     <Named Decision Data> ::= <<Install Decision> |
                                 <Remove Decision>>

     <Install Decision>    ::= *(<PRID> <EPD>)

     <Remove Decision>     ::= *(<PRID>|<PPRID>)

   Note that PRID objects in a Remove Decision may specify PRID prefix
   values.  Explicit and implicit deletion of installed policies is
   supported by a client.  Install Decision data MUST be explicit (i.e.,
   PRID prefix values are illegal and MUST be rejected by a client).

5.2. ClientSI Request Data

   The provisioning client request data will use same bindings as
   described above.  The format for this data is encapsulated in the
   COPS Named ClientSI object as follows:

   <Named ClientSI: Request> ::= <*(<PRID> <EPD>)>

5.3. Policy Provisioning Report Data

   The COPS Named ClientSI object is used in the RPT message in
   conjunction with the accompanying COPS Report Type object to
   encapsulate COPS-PR report information from the PEP to the PDP.
   Report types can be 'Success' or 'Failure', indicating to the PDP
   that a particular set of provisioning policies has been either
   successfully or unsuccessfully installed/removed on the PEP, or
   'Accounting'.

5.3.1. Success and Failure Report-Type Data Format

   Report-types can be 'Success' or 'Failure' indicating to the PDP that
   a particular set of provisioning policies has been either
   successfully or unsuccessfully installed/removed on the PEP.  The
   provisioning report data consists of the bindings described above and
   global and specific error/warning information. Specific errors are
   associated with a particular instance.  For a 'Success' Report-Type,
   a specific error is an indication of a warning related to a specific
   policy that has been installed, but that is not fully implemented
   (e.g., its parameters have been approximated) as identified by the
   ErrorPRID object.  For a 'Failure' Report-Type, this is an error code
   specific to a binding, again, identified by the ErrorPRID object.
   Specific errors may also include regular <PRID><EPD> bindings to





Chan, et al.                Standards Track                    [Page 24]

RFC 3084                        COPS-PR                       March 2001


   carry additional information in a generic manner so that the specific
   errors/warnings may be more verbosely described and associated with
   the erroneous ErrorPRID object.

   Global errors are not tied to a specific ErrorPRID.  In a 'Success'
   RPT message, a global error is an indication of a general warning at
   the PEP level (e.g., memory low).  In a 'Failure' RPT message, this
   is an indication of a general error at the PEP level (e.g., memory
   exhausted).

   In the case of a 'Failure' Report-Type the PEP MUST report at least
   the first error and SHOULD report as many errors as possible.  In
   this case the PEP MUST roll-back its configuration to the last good
   transaction before the erroneous Decision message was received.

   The format for this data is encapsulated in the COPS Named ClientSI
   object as follows:

   <Named ClientSI: Report> ::= <[<GPERR>] *(<report>)>

   <report> ::= <ErrorPRID> <CPERR> *(<PRID><EPD>)

5.3.2. Accounting Report-Type Data Format

   Additionally, reports can be used to carry accounting information
   when specifying the 'Accounting' Report-Type.  This accounting report
   message will typically carry statistical or event information related
   to the installed configuration for use at the PDP.  This information
   is encoded as one or more <PRID><EPD> bindings that generally
   describe the accounting information being reported from the PEP to
   the PDP.

   The format for this data is encapsulated in the COPS Named ClientSI
   object as follows:

   <Named ClientSI: Report> ::= <*(<PRID><EPD>)>

   NOTE: RFC 2748 defines an optional Accounting-Timer (AcctTimer)
   object for use in the COPS Client-Accept message.  Periodic
   accounting reports for COPS-PR clients are also obligated to be paced
   by this timer.  Periodic accounting reports SHOULD NOT be generated
   by the PEP more frequently than the period specified by the COPS
   AcctTimer.  Thus, the period between new accounting reports SHOULD be
   greater-than or equal-to the period specified (if specified) in the
   AcctTimer.  If no AcctTimer object is specified by the PDP, then
   there are no constraints imposed on the PEP's accounting interval.





Chan, et al.                Standards Track                    [Page 25]

RFC 3084                        COPS-PR                       March 2001


6. Common Operation

   This section describes, in general, typical exchanges between a PDP
   and Policy Provisioning COPS client.

   First, a TCP connection is established between the client and server
   and the PEP sends a Client-Open message specifying a COPS- PR
   client-type (use of the ClientSI object within the Client-Open
   message is currently undefined for COPS-PR clients). If the PDP
   supports the specified provisioning client-type, the PDP responds
   with a Client-Accept (CAT) message.  If the client-type is not
   supported, a Client-Close (CC) message is returned by the PDP to the
   PEP, possibly identifying an alternate server that is known to
   support the policy for the provisioning client-type specified.

   After receiving the CAT message, the PEP can send requests to the
   server.  The REQ from a policy provisioning client contains a COPS
   'Configuration Request' context object and, optionally, any relevant
   named client specific information from the PEP.  The information
   provided by the PEP should include available client resources (e.g.,
   supported classes/attributes) and default policy configuration
   information as well as incarnation data on existing policy.  The
   configuration request message from a provisioning client serves two
   purposes.  First, it is a request to the PDP for any provisioning
   configuration data which the PDP may currently have that is suitable
   for the PEP, such as access control filters, etc., given the
   information the PEP specified in its REQ.  Also, the configuration
   request effectively opens a channel that will allow the PDP to
   asynchronously send policy data to the PEP, as the PDP decides is
   necessary, as long as the PEP keeps its request state open (i.e., as
   long as the PEP does not send a DRQ with the request state's Client
   Handle).  This asynchronous data may be new policy data or an update
   to policy data sent previously.  Any relevant changes to the PEP's
   internal state can be communicated to the PDP by the PEP sending an
   updated REQ message.  The PEP is free to send such updated REQ
   messages at any time after a CAT message to communicate changes in
   its local state.

   After the PEP sends a REQ, if the PDP has Policy Provisioning policy
   configuration information for the client, that information is
   returned to the client in a DEC message containing the Policy
   Provisioning client policy data within the COPS Named Decision Data
   object and specifying an "Install" Command-Code in the Decision Flags
   object.  If no filters are defined, the DEC message will simply
   specify that there are no filters using the "NULL Decision" Command-
   Code in the Decision Flags object.  As the PEP MUST specify a Client
   Handle in the request message, the PDP MUST process the Client Handle
   and copy it in the corresponding decision message.  A DEC message



Chan, et al.                Standards Track                    [Page 26]

RFC 3084                        COPS-PR                       March 2001


   MUST be issued by the PDP with the Solicited Message Flag set in the
   COPS message header, regardless of whether or not the PDP has any
   configuration information for the PEP at the time of the request.
   This is to prevent the PEP from timing out the REQ and deleting the
   Client Handle.

   The PDP can then add new policy data or update/delete existing
   configurations by sending subsequent unsolicited DEC message(s) to
   the PEP, with the same Client Handle.  Previous configurations
   installed on the PEP are updated by the PDP by simply re-installing
   the same instance of configuration information again (effectively
   overwriting the old data).  The PEP is responsible for removing the
   Client handle when it is no longer needed, for example when an
   interface goes down, and informing the PDP that the Client Handle is
   to be deleted via the COPS DRQ message.

   For Policy Provisioning purposes, access state, and access requests
   to the policy server can be initiated by other sources besides the
   PEP.  Examples of other sources include attached users requesting
   network services via a web interface into a central management
   application, or H.323 servers requesting resources on behalf of a
   user for a video conferencing application.  When such a request is
   accepted, the edge device affected by the decision (the point where
   the flow is to enter the network) needs to be informed of the
   decision.  Since the PEP in the edge device did not initiate the
   request, the specifics of the request, e.g., flowspec, packet filter,
   and PHB to apply, needs to be communicated to the PEP by the PDP.
   This information is sent to the PEP using the Decision message
   containing Policy Provisioning Named Decision Data objects in the
   COPS Decision object as specified.  Any updates to the state
   information, for example in the case of a policy change or call tear
   down, is communicated to the PEP by subsequent unsolicited DEC
   messages containing the same Client Handle and the updated Policy
   Provisioning request state.  Updates can specify that policy data is
   to be installed, deleted, or updated (re-installed).

   PDPs may also command the PEP to open a new Request State or delete
   an exiting one by issuing a decision with the Decision Flags object's
   Request-State flag set.  If the command-code is "install", then the
   PDP is commanding the PEP to create a new Request State, and
   therefore issue a new REQ message specifying a new Client Handle or
   otherwise issue a "Failure" RPT specifying the appropriate error
   condition.  Each request state represents an independent and
   logically non-overlapping namespace, identified by the Client Handle,
   on which transactions (a.k.a., configuration installations,
   deletions, updates) may be performed.  Other existing Request States
   will be unaffected by the new request state as they are independent
   (thus, no instances of configuration data within one Request State



Chan, et al.                Standards Track                    [Page 27]

RFC 3084                        COPS-PR                       March 2001


   can be affected by DECs for another Request State as identified by
   the Client Handle).  If the command-code is "Remove", then the PDP is
   commanding the PEP to delete the existing Request-State specified by
   the DEC message's Client Handle, thereby causing the PEP to issue a
   DRQ message for this Handle.

   The PEP MUST acknowledge a DEC message and specify what action was
   taken by sending a RPT message with a "Success" or "Failure" Report-
   Type object with the Solicited Message Flag set in the COPS message
   header.  This serves as an indication to the PDP that the requestor
   (e.g., H.323 server) can be notified whether the request has been
   accepted by the network or not.  If the PEP needs to reject the DEC
   operation for any reason, a RPT message is sent with a Report-Type
   with the value "Failure" and optionally a Client Specific Information
   object specifying the policy data that was rejected.  Under such
   solicited report failure conditions, the PEP MUST always rollback to
   its previously installed (good) state as if the DEC never occurred.
   The PDP is then free to modify its decision and try again.

   The PEP can report to the PDP the current status of any installed
   request state when appropriate.  This information is sent in a
   Report-State (RPT) message with the "Accounting" flag set.  The
   request state that is being reported is identified via the associated
   Client Handle in the report message.

   Finally, Client-Close (CC) messages are used to cancel the
   corresponding Client-Open message.  The CC message informs the other
   side that the client-type specified is no longer supported.

7. Fault Tolerance

   When communication is lost between PEP and PDP, the PEP attempts to
   re-establish the TCP connection with the PDP it was last connected
   to.  If that server cannot be reached, then the PEP attempts to
   connect to a secondary PDP, assumed to be manually configured (or
   otherwise known) at the PEP.

   When a connection is finally re-established with a PDP, the PEP sends
   a OPN message with a <LastPDPAddr> object providing the address of
   the most recent PDP for which it is still caching decisions.  If no
   decisions are being cached on the PEP (due to reboot or TTL timeout
   of state) the PEP MUST NOT include the last PDP address information.
   Based on this object, the PDP may request the PEP to re-synch its
   current state information (by issuing a COPS SSQ message).  If, after
   re-connecting, the PDP does not request synchronization, the client
   can assume the server recognizes it and the current state at the PEP
   is correct, so a REQ message need not be sent.  Still, any state
   changes which occurred at the PEP that the PEP could not communicate



Chan, et al.                Standards Track                    [Page 28]

RFC 3084                        COPS-PR                       March 2001


   to the PDP due to communication having been lost, MUST be reported to
   the PDP via the PEP sending an updated REQ message.  Whenever re-
   synchronization is requested, the PEP MUST reissue any REQ messages
   for all known Request-States and the PDP MUST issue DEC messages to
   delete either individual PRIDs or prefixes as appropriate to ensure a
   consistent known state at the PEP.

   While the PEP is disconnected from the PDP, the active request-state
   at the PEP is to be used for policy decisions.  If the PEP cannot
   re-connect in some pre-specified period of time, all installed
   Request-States are to be deleted and their associated Handles
   removed.  The same holds true for the PDP; upon detecting a failed
   TCP connection, the time-out timer is started for all Request-States
   associated with the PEP and these states are removed after the
   administratively specified period without a connection.

8. Security Considerations

   The COPS protocol [COPS], from which this document derives, describes
   the mandatory security mechanisms that MUST be supported by all COPS
   implementations.  These mandatory security mechanisms are used by the
   COPS protocol to transfer opaque information from PEP to PDP and vice
   versa in an authenticated and secure manner.  COPS for Policy
   Provisioning simply defines a structure for this opaque information
   already carried by the COPS protocol.  As such, the security
   mechanisms described for the COPS protocol will also be deployed in a
   COPS-PR environment, thereby ensuring the integrity of the COPS-PR
   information being communicated.  Furthermore, in order to fully
   describe a practical set of structured data for use with COPS-PR, a
   PIB (Policy Information Base) will likely be written in a separate
   document.  The authors of such a PIB document need to be aware of the
   security concerns associated with the specific data they have
   defined.  These concerns MUST be fully specified in the security
   considerations section of the PIB document along with the required
   security mechanisms for  transporting this newly defined data.

9. IANA Considerations

   COPS for Policy Provisioning follows the same IANA considerations for
   COPS objects as the base COPS protocol [COPS].  COPS-PR has defined
   one additional Decision Flag value of 0x02, extending the COPS base
   protocol only by this one value.  No new COPS Client- Types are
   defined by this document.

   COPS-PR also introduces a new object number space with each object
   being identified by its S-Num and S-Type value pair.  These objects
   are encapsulated within the existing COPS Named ClientSI or Named
   Decision Data objects [COPS] and, therefore, do not conflict with any



Chan, et al.                Standards Track                    [Page 29]

RFC 3084                        COPS-PR                       March 2001


   assigned numbers in the COPS base protocol.  Additional S-Num and S-
   Type pairs can only be added to COPS-PR using the IETF Consensus rule
   as defined in [IANA].  These two numbers are always to be treated as
   a pair, with one or more S-Types defined per each S-Num.  This
   document defines the S-Num values 1-6 and the S-Type 1 for each of
   these six values (note that the S-Type value of 2 is reserved for
   transport of XML encoded data).  A listing of all the S-Num and S-
   Type pairs defined by this document can be found in sections 4.1-4.6.

   Likewise, additional Global Provisioning error codes and Class-
   Specific Provisioning error codes defined for COPS-PR can only be
   added with IETF Consensus.  This document defines the Global
   Provisioning error code values 1-11 in section 4.4 for the Global
   Provisioning Error Object (GPERR).  This document also defines the
   Class-Specific error code values 1-13 in section 4.5 for the Class
   Provisioning Error Object (CPERR).

10. Acknowledgements

   This document has been developed with active involvement from a
   number of sources.  The authors would specifically like to
   acknowledge the valuable input given by Michael Fine, Scott Hahn, and
   Carol Bell.

11. References

   [COPS]    Boyle, J., Cohen, R., Durham, D., Herzog, S., Raja, R. and
             A. Sastry, "The COPS (Common Open Policy Service)
             Protocol", RFC 2748, January 2000.

   [RAP]     Yavatkar, R., Pendarakis, D. and R. Guerin, "A Framework
             for Policy Based Admission Control", RFC 2753, January
             2000.

   [COPRSVP] Boyle, J., Cohen, R., Durham, D., Herzog, S., Raja, R. and
             A. Sastry, "COPS usage for RSVP", RFC 2749, January 2000.

   [ASN1]    Information processing systems - Open Systems
             Interconnection, "Specification of Abstract Syntax Notation
             One (ASN.1)", International Organization for
             Standardization, International Standard 8824, December
             1987.

   [BER]     Information processing systems - Open Systems
             Interconnection - Specification of Basic Encoding Rules for
             Abstract Syntax Notation One (ASN.1), International
             Organization for Standardization. International Standard
             8825, (December, 1987).



Chan, et al.                Standards Track                    [Page 30]

RFC 3084                        COPS-PR                       March 2001


   [RFC2475] Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z. and
             W. Weiss, "An Architecture for Differentiated Service," RFC
             2475, December 1998.

   [SPPI]    McCloghrie, K., Fine, M., Seligson, J., Chan, K., Hahn, S.,
             Sahita, R., Smith, A. and F. Reichmeyer, "Structure of
             Policy Provisioning Information SPPI", Work in Progress.

   [V2SMI]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
             Rose, M. and S. Waldbusser, "Structure of Management
             Information Version 2(SMIv2)", STD 58, RFC 2578, April
             1999.

   [RFC2234] Crocker, D. and P. Overell, "Augmented BNF for Syntax
             Specifications: ABNF", RFC 2234, November 1997.

   [IANA]    Alvestrand, H. and T. Narten, "Guidelines for writing an
             IANA Considerations Section in RFCs", BCP 26, RFC 2434,
             October 1998.

   [URN]     Moats, R., "Uniform Resource Names (URN) Syntax", RFC 2141,
             May 1997.

   [XML]     World Wide Web Consortium (W3C), "Extensible Markup
             Language (XML)," W3C Recommendation, February, 1998,
             http://www.w3.org/TR/1998/REC-xml-19980210.

























Chan, et al.                Standards Track                    [Page 31]

RFC 3084                        COPS-PR                       March 2001


12. Authors' Addresses

   Kwok Ho Chan
   Nortel Networks, Inc.
   600 Technology Park Drive
   Billerica, MA 01821

   Phone: (978) 288-8175
   EMail: khchan@nortelnetworks.com


   David Durham
   Intel
   2111 NE 25th Avenue
   Hillsboro, OR 97124

   Phone: (503) 264-6232
   Email: david.durham@intel.com

   Silvano Gai
   Cisco Systems, Inc.
   170 Tasman Dr.
   San Jose, CA 95134-1706

   Phone: (408) 527-2690
   EMail: sgai@cisco.com


   Shai Herzog
   IPHighway Inc.
   69 Milk Street, Suite 304
   Westborough, MA 01581

   Phone: (914) 654-4810
   EMail: Herzog@iphighway.com


   Keith McCloghrie

   Phone: (408) 526-5260
   EMail: kzm@cisco.com










Chan, et al.                Standards Track                    [Page 32]

RFC 3084                        COPS-PR                       March 2001


   Francis Reichmeyer
   PFN, Inc.
   University Park at MIT
   26 Landsdowne Street
   Cambridge, MA 02139

   Phone: (617) 494 9980
   EMail: franr@pfn.com


   John Seligson
   Nortel Networks, Inc.
   4401 Great America Parkway
   Santa Clara, CA 95054

   Phone: (408) 495-2992
   Email: jseligso@nortelnetworks.com


   Raj Yavatkar

   Phone: (503) 264-9077
   EMail: raj.yavatkar@intel.com


   Andrew Smith
   Allegro Networks
   6399 San Ignacio Ave.
   San Jose, CA 95119, USA

   EMail: andrew@allegronetworks.com




















Chan, et al.                Standards Track                    [Page 33]

RFC 3084                        COPS-PR                       March 2001


13. Full Copyright Statement

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.



















Chan, et al.                Standards Track                    [Page 34]