💾 Archived View for spam.works › mirrors › textfiles › apple › ANATOMY › rwts.drvr.seek.txt captured on 2023-06-16 at 21:11:45.
View Raw
More Information
-=-=-=-=-=-=-
- ::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::*
- *
- RWTSDRVR using SEEK *
- *
- ----------------------------------------------------------------*
- *
- Just as the file manager is used to manipulate entire *
- files at once, RWTS reads or writes disk data one sector at a *
- time. The software interface between these two levels of DOS *
- management is represented by the RWTS driver routines *
- (RWTSDRVR, $B052 and RWTSDRV1, $B058). RWTSDRVR is called any *
- time the file manager wants to seek a given track or read or *
- write a sector of disk data. This routine is always entered *
- with the accumulator containing the RWTS opcode ($00=seek, *
- $01=read, $03=write) and the x- and y-registers housing the *
- target track and sector values. Although RWTSDRV1 is only *
- directly called via the INIT function handler (with the *
- accumlator containing the format ($04) opcode), execution *
- falls into RWTSDRV1 from RWTSDRVR. The driver routines check *
- to see if data are to be output to the disk and condition the *
- carry flag accordingly. The carry is set if the format or *
- write opcodes are detected. After setting up RWTS's parameter *
- list (also known as an input/output block, IOB), the driver *
- calls ENTERWTS ($B7B5). *
- ENTERWTS preserves the conditioned carry flag by pushing *
- the status register on the stack. Next the interrupt disable *
- flag is set to prevent any maskable interrupts from interfer- *
- ring with the real-time subroutines employed by RWTS. *
- Finally, ENTERWTS calls RWTS proper ($BD00) to do the desired *
- function. Execution eventually returns to the ENTERWTS *
- routine at $B7BA. The saved status byte is thrown off the *
- stack, the carry flag is cleared or set (depending on whether *
- or not RWTS encountered an error) and then execution returns *
- to the caller of ENTERWTS. *
- After updating the last-used volume value in the FM *
- parameter list, the RWTSDRV1 routine checks the carry flag to *
- see if RWTS detected an error. If an error was encountered, *
- the carry is reset and execution returns to the calling *
- routine via ERRWTSDR ($B0A1). If no error was detected, the *
- "BCS ERRWTSDR" instruction at $B09E is skipped and execution *
- returns to the caller of the driving routine with the carry *
- clear. *
- Note that ENTERWTS is the one and only DIRECT caller of *
- RWTS. THE DOS MANUAL recommends the following procedure be *
- employed to call RWTS from an assembly language program: *
- 1) Set up the IOB and DCT tables accordingly. *
- 2) Load the y-register and accumulator with the low and *
- high bytes (respectively) of the address of the IOB. *
- 3) JSR to $3D9. (The instruction at $3D9 normally *
- contains a jump to ENTERWTS.) *
- The execution pattern of RWTS and its associated sub- *
- routines is long, but not particularly complex. On the one *
- hand RWTS is rather simple because it can only perform four *
- types of functions (seek, read, write or format). However, *
- many people find RWTS difficult to understand because: *
- 1) It is the only portion of DOS that uses time-critical *
- code. *
- 2) Two different methods are used to encode information *
- on the disk. *
- 3) The actual method by which the read/write head is *
- moved to different track positions on the disk is not *
- well publicized. *
- Time critical code and data encoding information are clearly *
- explained in chapter 3 of BENEATH APPLE DOS. (When reading *
- this reference, you may find it elcudiating to keep in mind *
- that some protected disks (such as LOCKSMITH by ALPHA LOGIC *
- BUSINESS SYSTEMS) modify the read/write routines to EOR each *
- sector of data with its sector number.) *
- *
- The positioning of the read/write head is the only *
- function of the seek command. Positioning actually occurs in *
- the SEEKIT routine ($BE6B). The seek command is described in *
- the disassembly given below. Because the following source *
- code is very highly commented and because most of it is common *
- to all of RWTS's functions, you are urged to read the follow- *
- ing disassembly over carefully a few times. A quicker under- *
- standing may be achieved if you keep the following information *
- in mind: *
- - Data are written on the disk in 35 circular paths or *
- concentric circles called tracks. Track $00 is located at *
- the outer edge of the disk, whereas track $22 (#34) is *
- represented by the innermost concentric circle. Each track *
- is divided into 16 segments ($00 to $0F) called sectors. *
- - A disk controller card can be used in any peripheral slot *
- except slot $00. Each of the remaining seven slots ($01 to *
- $07) can contain a controller card. Two different drives *
- can be operated from one controller card. Therefore, you *
- can hang up to 14 different drives from a single Apple II, *
- II+ or IIe machine. *
- - The disk controller ROM is relocatable and is copied into *
- the computer's memory at $Cs00 to $CsFF (where s = slot *
- number). All drive functions are performed by indirectly *
- referencing base addrs $C000 to $C00F. The motor-on-off, *
- drive selection and read-write switches are indexed with an *
- offset equal to slot * 16. The four different stepper motor *
- magnets are all referenced via the $C080 base addr. The *
- index used = (slot*16)+bits0and1 of halftrack# + carry. The *
- slot & bit portions of the index are used to select the *
- desired magnet. The added carry is used to make the *
- effective addr even or odd in order to turn the magnet off *
- or on. The EFFECTIVE addresses for all drive functions are *
- shown below: *
- MAG0FF = $C0s0 ;Turn stepper motor magnet 0 off. *
- MAG0N = $C0s1 ;Turn stepper motor magnet 0 on. *
- MAG1OFF = $C0s2 ;Turn stepper motor magnet 1 off. *
- MAG1ON = $C0s3 ;Turn stepper motor magnet 1 on. *
- MAG2OFF = $C0s4 ;Turn stepper motor magnet 2 off. *
- MAG2ON = $C0s5 ;Turn stepper motor magnet 2 on. *
- MAG3OFF = $C0s6 ;Turn stepper motor magnet 3 off. *
- MAG3ON = $C0s7 ;Turn stepper motor magnet 3 on. *
- MTR0FF = $C0s8 ;Wake up controller and spin disk. *
- ;This switch must be thrown before a *
- ;specific drive (1 or 2) is selected. *
- MTR0N = $C0s9 ;Turn disk drive motor off. *
- SELDRV1 = $C0sA ;Select drive number 1. *
- SELDRV2 = $C0sB ;Select drive number 2. *
- The following addresses are used to read or write data *
- bytes or to check the status of the write protect switch. *
- As shown below, they are always used in specific combinations *
- to evoke a certain range of responses from the controller *
- card. The firmware affected on the controller card is called *
- a logic state sequencer. It is a nibble-based language that *
- only contains six different instructions and is transparent to *
- the monitor ROM disassembler. (See UNDERSTANDING THE APPLE II *
- by Jim Sather for further explaination.) *
- Q6L = $C0sC ;Shift byte in or out of data latch. *
- Q6H = $C0sD ;Load latch from data bus. *
- Q7L = $C0sE ;Prepare to read. *
- Q7H = $C0sF ;Prepare to write. *
- When used in combinations: *
- Q7L plus Q6L = select read sequence and then read a byte. *
- Q6H plus Q7L = check write protect switch and select write *
- sequence. *
- Q7H plus Q6H = select write sequence and load data register *
- with output byte. *
- Q6H plus Q6L = load latch from data bus and write byte. *
- (Must have previously selected Q7H.) *
- - Each disk drive contains two motors. One motor (usually *
- referred to as the "drive motor") spins the disk at a *
- constant speed. (When the drive motor is first turned on, a *
- delay is used to wait for the drive to come up to speed *
- before attempting to read or write disk bytes.) Another *
- motor (called a "stepper motor") moves the read/write head *
- across the disk to position the head at different track *
- positions. *
- - The stepper motor can be envisioned as containing a central *
- magnet on a rotatable shaft and a circle of four fixed *
- magnets (magnets 0 to 3) surrounding the shaft. Each time a *
- peripheral magnet is enegized, the central shaft is rotated *
- until its magnet is in line with the energized peripheral *
- magnet. By turning the fixed peripheral magnets on and off *
- in sequence, we can spin the shaft of the stepper motor. *
- Movement of this shaft causes the read/write head to "step" *
- across the disk. Each time the next magnet in sequence is *
- turned on, the shaft is rotated one quarter turn. One *
- quarter turn of the shaft moves the read/write head half a *
- track width. *
- - Normally, DOS only writes data at even magnet positions *
- because the drive head does not have good enough resolution *
- to distinguish information in adjacent half-track positions. *
- The drive head is stepped to a higher track position as the *
- magnets are turned on and off in ascending order. *
- Similarly, a descending reference to the magnets causes *
- movement to a lower track position. Each time a magnet is *
- turned on or off, a delay is used to give the shaft magnet *
- time to properly align with a peripheral magnet. The amount *
- of delay used is inversely proportional to the acceleration *
- of the motor. An example of the on/delay/off sequence used *
- to step the head from track $02 to track $04 is shown below: *
- 1on - delay - 0off - delay - 2on - delay - 1off - delay - *
- 3on - delay - 2off - delay - 0on - delay - 3off - delay - *
- 0off - delay. *
- Similarly, moving the head from track $04 to track $02 *
- requires the following sequence: *
- 3on - delay - 0off - delay - 2on - delay - 3off - delay - *
- 1on - delay - 2off - delay - 0on - delay - 1off - delay - *
- 0off. *
- Note that the last-energized magnet is always turned off. *
- This is done as a safety measure because magnet-1-on is *
- hard wired into the write protect switch. (The boot process *
- is an exception to this rule. The controller ROM leaves *
- magnet0 energized.) *
- - Some protected programs modify DOS to skip entire tracks or *
- write data at odd-numbered magnet positions. However, *
- because the controller ROM always uses track $00 and because *
- crosstalk occurs when data is less than one full track width *
- apart, the data is actually written on a half-track disk at *
- the following track positions: 0, 1+1/2, 2+1/2, 3+1/2, ..., *
- 31+1/2, 32+1/2, 33+1/2. For instance, if you wanted to move *
- the head from track $02 to track $04+1/2, you could add the *
- following sequence to that described above: *
- - delay - 1on - delay - 0off - 1 off -delay. *
- - Data can even be written on quarter track positions (that *
- is, tracks 0, 1+1/4, 2+1/4, ..., 31+1/4, 32+1/4, 33+1/4) by *
- turning on two adjacent magnets almost simultaneously in *
- order to position the head between the two magnets. For *
- instance, if you wanted to move from track $02 to track *
- $04+1/4, you could patch DOS to automatically add the *
- following instructions to the normal sequence described *
- above: - 1on - no delay - 0on - very short delay - 1off - *
- no delay - 0off - delay. *
- *
- ::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::*
(B052)
RWTSDRVR STX IBTRK ;Enter with (x) = trk wntd.
STY IBSECT ; (y) = sector wntd.
RWTSDRV1 STA IBCMD ; (a) = opcode for RWTS.
(B058) ;RWTSDRV1 is the entry point used by the
;Init function handler.
(B05B) CMP #2 ;Is cmd a write?
(B05D) BNE SKPWRSET ;No, so branch. Note: "CMP" conditions:
;(c)=0 if seek ($00) or read ($01).
;(c)=1 if write ($02) or format ($03).
(B05F) ORA UPDATFLG ;Condition UPDATFLG to designate that
(B062) STA UPDATFLG ;last operation was a write for next
;time around.
- Finish setting up RWTS's
- input/output block (IOB).
(B065)
SKPWRSET LDA VOLWA ;Put complimented vol in IOB.
EOR #$FF
STA IBVOL
LDA SLOT16WA ;Put slot*16 in IOB.
STA IBSLOT
LDA DRVWA ;Put drive in IOB.
STA IBDRVN
LDA SECSIZWA ;Put sector length in IOB
STA IBSECSZ ;(standard size of dec. 256
LDA SECSIZWA+1 ;or hex $0100 bytes).
STA IBSECSZ+1
LDA #1 ;ALWAYS designate table type as 1.
STA IBTYPE
LDY ADRIOB ;Set (y) & (a) to point
LDA ADRIOB+1 ;at RWTS's IOB.
(B090) JSR ENTERWTS ;Go call RWTS.
* Route execution to RWTS.
* (Normal entry route to RWTS for custom
* assembly language programs. See preamble
* for required entry conditions.)
(B7B5)
ENTERWTS PHP ;Save status reg (with conditioned carry) on stk.
;(c) = 0 if doing seek ($00) or read ($01).
;(c) = 1 if doing write ($02) or format ($03).
(B7B6) SEI ;Set interrupt disable flag to prevent
(B7B7) JSR RWTS ;any further maskable interrupts
;when doing real-time programming.
* Read/Write Track/Sector (RWTS).
* Enter with (y)/(a) pointing at
* RWTS's input/output block (IOB).
(BD00)
RWTS STY PTR2IOB ;Set up a zero page
STA PTR2IOB+1 ;pointer to RWTS's IOB.
LDY #2 ;Initialize cntr for max of 2 recalibs.
STY RECLBCNT
LDY #4 ;Initialize cntr for # or re-seeks betwn recalibs.
STY RSEEKCNT
LDY #1 ;Get slot*16 from IOB & put it
LDA (PTR2IOB),Y ;in (x) so can use it to index
(BD12) TAX ;base addresses for drive functions.
* Check if wanted slot*16 = last slot*16.
(BD13) LDY #15 ;Index to get val of last slot used.
CMP (PTR2IOB),Y ;Compare wanted vs last.
(BD17) BEQ SAMESLOT ;Take branch if using same slot.
* Want to use different slot so reset (x)
* back to index old slot so can test old motor.
(BD19) TXA ;Save slot*16 wanted on stk.
PHA
LDA (PTR2IOB),Y ;Get old slot*16 back and
TAX ;stick it in (x) to index base addrs.
PLA ;Get slot*16 wanted into (a) from stk
PHA ;and keep it saved on stk.
(BD20) STA (PTR2IOB),Y ;Update last-used slot*16 for next time.
* Check to see if last-used drive assoc with last-
* used slot is still spinning. If it is, wait for
* it to stop.
(BD22) LDA Q7L,X ;Prep latch for input.
CKSPIN LDY #8 ;Set cntr to insure at least 8 chks.
LDA Q6L,X ;Strobe latch to read.
CHKCHNG CMP Q6L,X ;Read again & cmp to last read.
BNE CKSPIN ;Data changed, so still spinning.
DEY ;No change, so chk with some
(BD30) BNE CHKCHNG ;delays just to make sure.
* Get index for slot wanted.
(BD32) PLA ;Get slot*16 back off stk
(BD33) TAX ;and put it in (x).
* Chk to see if a drive assoc with slot wanted
* is still spinning. (As soon as get a change then
* know it's spinning. If no change, chk at least
* 8 times to be certain it is off.)
(BD34)
SAMESLOT LDA Q7L,X ;Set read mode.
LDA Q6L,X ;Strobe latch to read.
LDY #8 ;Set cntr for 8 chks if needed.
STRBAGN LDA Q6L,X ;Strobe latch again.
PHA ;Delay 14 machine cycles.
PLA
PHA
PLA
STX SLOTPG5 ;Save slot*16 wntd in page 5.
CMP Q6L,X ;Has data changed yet?
BNE DONETEST ;Yes - data changed, so disk spinning.
DEY ;No - no change, see if chkd enough times.
BNE STRBAGN ;Chk at least 8 times.
DONETEST PHP ;Save test results on stk so can later
(BD4E) ;chk if need extra delay or not.
* Turn motor on in a drive assoc with slot wanted
* (just in case it wasn't already spinning).
* Note: This uses drive with same # as last
* drive used. This may or may not be the
* specific drive # we want. However, we must use
* this instruction to send power via the controller.
* Once this switch is thrown, we can later re-route
* that power to whichever drive we want by throwing
* another switch to select drive1 or drive2.
(BD4F) LDA MTRON,X ;Turn motor on.
* Establish z-page pointers to device characteristic
* table (DCT) and RWTS's I/O buffer (so can use z-page
* indirect addressing modes).
* IBDCTP ---> PTR2DCT (3C,3D)
* IBBUFP ---> PTR2BUF (3E,3F)
(BD52) LDY #6 ;Get ptrs from RWTS's IOB
MOVPTRS LDA (PTR2IOB),Y ;and put them in z-page.
(BD56) STA: PTR2DCT-6,Y ;(Note: ":" used to force
;a 3-byte instruction.)
(BD59) INY
CPY #10 ;4 bytes to copy (6 to 9).
(BD5C) BNE MOVPTRS
* Check drive status.
(BD5E) LDY #3 ;Save hi byte of motor-on-time
LDA (PTR2DCT),Y ;count in z-page.
STA MTRTIME+1
LDY #2 ;Get drive # wanted.
LDA (PTR2IOB),Y
LDY #16 ;Set (y) = index to last-used drive.
CMP (PTR2IOB),Y ;Drv wanted vs drv last used.
BEQ SAMEDRV
(BD6E) STA (PTR2IOB),Y ;Designate drv wanted as old drv
;for next time around.
(BD70) PLP ;Get status back off stk.
(BD71) LDY #0 ;Reset status (z-flag off) to signal that
;SPECIFIC DRIVE # we want in SPECIFIC SLOT
;wanted was not originally spinning.
(BD73) PHP ;Push updated status back on stk.
SAMEDRV ROR ;Put low bit of drv wanted in carry.
BCC USEDRV2 ;Branch if want drive 2.
LDA SELDRV1,X ;Route power to select drive 1.
BCS USEDRV1 ;ALWAYS.
USEDRV2 LDA SELDRV2,X ;Route power to select drive 2.
USEDRV1 ROR DRVZPG ;Put sign bit for which drive
(BD7F) ;using in z-page: neg = drive1.
; pos = drive2.
* Chk to see if a specific drive wanted in
* specific slot wanted was originally on or not.
(BD81) PLP ;Get previous test result.
PHP ;Put it back on stk for later use.
(BD83) BNE WASON ;Orig drv in orig slot was on.
* Specific drive wanted in specific slot
* wanted was ORIGINALLY OFF, so delay a
* bit to avoid positioning head during
* the period of heavy current flow that
* occurs when motor is turned on. (That
* is, give line/capacitor time to
* bleed down cause motor on/off switch
* requires more current than stepper motor.)
*
* (Amount of delay is not constant cause
* it depends on what is in accum & we don't
* know cause we were just accessing hardware.)
(BD85) LDY #7
WAIT4MTR JSR DELAY ;Stall.
(BD87)
* Main delay routine in DOS.
* (Amt of delay = 100 * (a) microsecs.)
(BA00)
DELAY LDX #17
DLY1 DEX
BNE DLY1
INC MTRTIME
BNE DLY2
INC MTRTIME+1
DLY2 SEC
SBC #1
BNE DELAY
(BA10) RTS
(BD8A) DEY
BNE WAIT4MTR ;Go stall some more.
(BD8D) LDX SLOTPG5 ;Restore (x) = slot*16.
(BD90)
WASON LDY #4 ;Get trk wanted.
LDA (PTR2IOB),Y
(BD94) JSR SEEKTRK ;Go move arm to desired trk.
(BE5A)
SEEKTRK PHA ;Save # of trk wntd on stk.
LDY #1 ;Get drive type (1- or 2-phase)
(BE5D) LDA (PTR2DCT),Y ;from DCT. (P.S. the "II" in the
;"DISK II" logo stamped on Apple's
;disk drive denotes a two-phase
;stepper motor.)
(BE5F) ROR ;Put low byte of drive type in carry.
PLA ;Get trk# wanted back in (a).
(BE61) BCC SEEKIT ;Not using standard DRIVEII, using a
;one-phase drive instead, ther4 skip
;doubling of trk # & use SEEKIT as part
;of routine instead of a subroutine.
* Using a two-phase drive.
(BE63) ASL ;Double trk # wanted to get
;number of 1/2 trk wanted.
(BE64) JSR SEEKIT ;Move disk arm to desired track.
(BE6B)
SEEKIT .
.
.
---------------------------------------------
l * Routine/subroutine to move drive arm
l * to a specific trk position.
l * Used as a subroutine when using Apple's
l * disk drive II. Note when SEEKIT is used as a
l * subroutine, DESTRK, PRESTRK, TRK4DRV1, TRK4DRV2,
l * STPSDONE and HOLDPRES are all expressed in half
l * tracks:
l * DESTRK = destination half-track position.
l * PRESTRK = present half-track position.
l * HOLDPRES = present half-track position.
l * TRK4DRV1 = base addr (when indexed by slot*16) pts
l * at the addr that contains the last half-
l * track # that drive 1 was aligned on.
l * TRK4DRV2 = base addr (when indexed by slot*16) pts
l * at the addr that contains the last half-
l * track # that drive 2 was aligned on.
l * STPSDONE = number of half tracks moved so far.
l * If not using a II-phase drive, change all
l * comments that read "half tracks" to read
l * "full tracks".
l (BE6B)
l SEEKIT STA DESTRK ;(a) = 2*trk # wanted.
l ; = # of halftrk wanted.
l (BE6D) JSR SLOTX2Y ;Set (y) = slot.
l
l * Convert slot*16 from
l * (x) to slot in (y).
l (BE8E)
l SLOTX2Y TXA ;Get slot*16 from (x).
l LSR ;Divide it by 16.
l LSR
l LSR
l LSR
l TAY ;Put slot # in (y).
l (BE94) RTS
l
l (BE70) LDA TRK4DRV1,Y ;Pres halftrk# assoc with drv1.
l (BE73) BIT DRVZPG ;Contains: neg = drive 1.
l ; pos = drive 2.
l (BE75) BMI SETPRSTK ;Branch if using drive 1.
l LDA TRK4DRV2,Y ;Using drv 2 so get pres 1/2trk#.
l SETPRSTK STA PRESTRK ;Save present halftrk#.
l (BE7A)
l
l * Designate halftrk we are about to seek
l * as present halftrk for next time around.
l * (Put halftrk info in slot dependent locations.)
l (BE7D) LDA DESTRK
l BIT DRVZPG ;Chk to see which drive we are using.
l BMI DRV1USG ;Branch if using drive 1.
l STA TRK4DRV2,Y ;Using drv2 -store halftrk 4 next time.
l BPL DRV2USG ;ALWAYS.
l DRV1USG STA TRK4DRV1,Y ;Using drv1 -store halftrk 4 next time.
l DRV2USG JMP SEEKABS
l (BE8B) -----------
l
l * Move drive head to a given halftrk position.
l * On entry: (x) = slot * 16.
l * (a) = destination halftrack pos'n.
l * PRESTRK = current halftrack pos'n.
l (B9A0)
l SEEKABS STX SLT16ZPG ;Save slot*16 in z-page.
l STA DESTRK ;Save destin halftrk #.
l CMP PRESTRK ;Dest halftrk = pres halftrk?
l BEQ ARRIVED ;Yes - we are already there, so exit.
l LDA #0 ;Init counter 4 # of halftrks moved.
l (B9AB) STA STPSDONE
l
l * Save current halftrk pos'n & calc
l * number of halftrks need to move minus 1.
l (B9AD)
l SAVCURTK LDA PRESTRK ;Save current halftrk pos'n.
l STA HOLDPRES
l SEC ;Calc (PRESTRK - DESTRK).
l SBC DESTRK
l BEQ ATDESTN ;At destin halftrk so go shutdown.
l (B9B7) BCS MOVDWN ;Pres halftrk > destin halftrk so
l ;want to move to lower trk.
l
l * Want to move to a higher halftrk #
l * (PRESTRK - DESTRK = neg result).
l
l (B9B9) EOR #$FF ;Convert neg to pos.
l (B9BB) INC PRESTRK ;Moving up, so inc current 1/2
l ;trk pos'n for next time around.
l (B9BE) BCC CKDLYNDX ;ALWAYS.
l ------------
l
l * Want to move to lower halftrk #
l * (PRESTRK - DESTRK = pos result).
l (B9C0)
l MOVDOWN ADC #$FE ;Simulate a subtract of 1. Actually
l ;adding minus 1 (#$FF) cause carry
l ;set. Want (a) to equal 1 less than
l ;number of halftrks to move.
l (B9C2) DEC PRESTRK ;Moving down so reduce pres 1/2
l ;trk number for next time around.
l
l * Check to see which index to use to
l * access the delay table. IF WE ARE
l * WITHIN 12 STEPS of the destination
l * or start positions, then use closest
l * distance to start or end pos'n to
l * index delay tables. Delay tables are
l * only 12 bytes long, so if more than 12
l * steps away from both start & destination,
l * then use last index (y=12) to access table.
l
l * Check if closer to destination or start pos'n.
l (B9C5)
l CKDLYNDX CMP STPSDONE ;Compare # of halftrks moved
l ;to # of halftrks need to move.
l (B9C7) BCC CLSR2ND ;Branch if closer to destn than start posn.
l
l * Closer to start.
l (B9C9) LDA STPSDONE ;Set (a) = dist from start pos'n.
l CLSR2ND CMP #12 ;Are we within 12 steps of start
l ;or destination pos'n?
l (B9CD) BCS TURNON ;We are at or beyond 12 steps from
l ;start or destn pos'n so use old
l ;index to access delay table.
l (B9CF)
l PRESNDX TAY ;Use present distance to index delay table.
l TURNON SEC ;Set carry so get odd index to base addr so
l (B9D0) ;magnet will be turned ON.
l (B9D1) JSR ONOROFF ;Turn magnet ON to suck stepper motor
l ;to correct halftrack pos'n.
l
l (B9EE)
l ONOROFF LDA PRESTRK ;Use lwr 2 bits of
l ENTRYOFF AND #%00000011 ;1/2 trk pos'n to
l ;index magnet.
l (B9F3) ROL ;2*halftrack+(c).
l ;If carry set,
l ;result is odd &
l ;magnet is energized.
l (B9F4) ORA SLT16ZPG ;Merge index to magnet
l ;with slot #.
l (B9F6) TAX ;Use (x) for indexing.
l (B9F7) LDA MAG0FF,X ;Use magnet0 off as
l ;base address.
l (B9FA) LDX SLT16ZPG ;Restore (x)=slot*16.
l ARRIVED RTS
l (B9FC)
l
l (B9D4) LDA ONTABLE,Y;Get time 2 leave magnet on from tbl.
l (B9D7) JSR DELAY ;Delay to give drive time to act before
l ;magnet is turned off again cause computer
l ;too fast 4 peripheral & want smooth mov't.
l
l * Main delay routine in DOS.
l * (Amt of delay = 100 * (a) microsecs.)
l (BA00)
l DELAY LDY #17
l DLY1 DEX
l BNE DLY1
l INC MTRTIME
l BNE DLY2
l INC MTRTIME+1
l DLY2 SEC
l SBC #1
l BNE DELAY
l (BA10) RTS
l
l (B9DA) LDA HOLDPRES ;Get last halftrk pos'n in (a).
l (B9DE) CLC ;Clr carry so index will come out even
l ;and there4 magnet will be turned OFF.
l (B9DD) JSR ENTRYOFF ;Turn magnet assoc with prev pos'n off.
l
l (B9F1)
l ENTRYOFF AND #%00000011 ;Halftrk pos'n to
l ;index magnet.
l (B9F3) ROL ;2*halftrk+(c).
l ;If carry set,
l ;result is odd &
l ;magnet is energized.
l (B9F4) ORA SLT16ZPG ;Merge index to magnet
l ;with slot #.
l (B9F6) TAX ;Use (x) for indexing.
l (B9F7) LDA MAG0FF,X ;Use magnet0 off as
l ;base address.
l (B9FA) LDX SLT16ZPG ;Restore (x)=slot*16.
l ARRIVED RTS
l (B9FC)
l
l (B9E0) LDA OFFTABLE,Y ;Get time 2 leave magnet off from table.
l (B9E3) JSR DELAY ;Leave magnet off for a while to give
l ;arm time to be properly aligned.
l ;(Need time to suck it over & also to
l ;decrease bounce or over-shoot.)
l
l * Main delay routine in DOS.
l * (Amt of delay = 100 * (a) microsecs.)
l (BA00)
l DELAY LDY #17
l DLY1 DEX
l BNE DLY1
l INC MTRTIME
l BNE DLY2
l INC MTRTIME+1
l DLY2 SEC
l SBC #1
l BNE DELAY
l (BA10) RTS
l
l (B9E6) INC STPSDONE
l (B9E8) BNE SAVCURTK ;ALWAYS.
l ------------
l
l * Arrived at destination halftrack.
l (B9EA)
l ATDESTN JSR DELAY ;Wait for peripheral again.
l
l * Main delay routine in DOS.
l * (Amt of delay = 100 * (a) microsecs.)
l (BA00)
l DELAY LDY #17
l DLY1 DEX
l BNE DLY1
l INC MTRTIME
l BNE DLY2
l INC MTRTIME+1
l DLY2 SEC
l SBC #1
l BNE DELAY
l (BA10) RTS
l
l * Turn last-used magnet off so exit with all
l * phases (ie. magnets) off because MAG1ON is
l * wired into the write-protect switch.
l (B9ED) CLC ;Turn magnet OFF.
l
l * Turn magnet on or off.
l (B9EE)
l ONOROFF LDA PRESTRK ;Use halftrk pos'n 2 index magnet.
l ENTRYOFF AND #%00000011 ;Only keep lwr 2 bits of halftrk#
l (B9F2) ;because only 4 magnets (0,1,2 & 3).
l (B9F3) ROL ;Multiply halftrk# * 2 and add (c)
l ;If (c)=1, result even, magnet off
l ;If (c)=0, result odd, magnet on
l (B9F4) ORA SLT16ZPG ;Merge index to magnet with slot #
l TAX ;Use (x) for indexing.
l LDA MAG0FF,X ;Use magnet-0-off as base addr.
l LDX SLT16ZPG ;Restore slot*16 in (x).
l ARRIVED RTS
l (B9FC)
l--------------------------------------------
.
.
.
-----------------------
l
l
(BE67) LSR PRESTRK ;Calc present whole trk #
;(ie. pres halftrk# / 2).
(BE6A) RTS
* Check to see if motor was originally on.
(BD97) PLP ;Get prev motor test result off stack.
BNE BEGINCMD ;Branch if motor was originally on.
(BD9A) LDY MTRTIME+1 ;Motor wasn't originally on. However, we
;have since turned in on. Now check if it
;has been on long enough.
(BD9C) BPL BEGINCMD ;Yes - no need to wait any longer.
* Although motor was turned on, it hasn't
* been on long enough to do accurate
* reading of bytes. There4, delay until
* motor on time is 1 second (at which time
* MTRTIME count is zero). (Part of time was
* taken up to seek track.)
(BD9E)
TIME1 LDY #18
TIME2 DEY
BNE TIME2
INC MTRTIME
BNE TIME1
INC MTRTIME+1
(BDA9) BNE TIME1
* Motor is up to speed so now process command.
* (Seek=00, Read=01, Write=02, Format=04.)
* Counters:
* READCNTR = allow up to 48 times to find correct
* addr prologue between re-seeking.
* RSEEKCNT = allow up to 4 re-seeks btwn recalibrations.
* RECLBCNT = allow up to 2 recalibrations.
* (There4, if necessary, allow up to 384
* attempts to find correct prologue addr.)
* Begin RWTS command processing.
(BDAB)
BEGINCMD LDY #12 ;Get cmd from IOB.
LDA (PTR2IOB),Y
(BDAF) BEQ WASEEK ;Branch if cmd was "seek".
----------
* Command was "SEEK" (null).
(BE0B)
WASEEK BEQ RWTSEXIT
------------
* Signal success or failure & then shut down.
* Note: Several references erroneously state that
* the error code is zero if no error occurred.
* However, a lone SEEK COMMAND ALWAYS SETS THE RETURN
* CODE TO ZERO. Even if a read or write operation
* is successful, the IOB error code will acquire a
* random value (as a result of accessing a hardware
* switch prior to entering this routine).
(BE46)
RWTSEXIT CLC ;Clr carry to signal successful operation.
HEX 24 ;"BIT $38" to skip "SEC" instruc below.
RWTSERR SEC ;Set carry to signal unsuccessful operation.
LDY #13 ;Store return code in IOB.
STA (PTR2IOB),Y
LDA MTROFF,X ;Turn motor off.
(BE50) RTS
(B7BA) BCS ERRENTER ;Branch if operation unsuccessful.
;(This branch is never taken with the seek command
;because that operation doesn't contain any
;facilities for error checking.)
(B7BC) PLP ;Throw status off stk.
CLC ;Signal successful.
(B7BE) RTS
============
(B093) LDA IBSMOD ;Get vol found from IOB
STA VOLFM ;& put it in Fm parm list.
LDA #$FF ;Designate vol wanted in
(B09B) STA IBVOL ;IOB as 255 for next time.
;(Actually using 0 cause FF EOR FF = 0.)
(B09E) BCS ERRWTSDR ;Branch if UNsuccessful operation.
;(Never taken when just doing a seek.)
(B0A0) RTS
============