💾 Archived View for spam.works › mirrors › textfiles › virus › datut005.txt captured on 2023-06-16 at 21:02:04.
-=-=-=-=-=-=-
?????????????????????????????????????
CODE OPTIMISATION, A BEGINNER'S GUIDE
?????????????????????????????????????
Written by Dark Angel
?????????????????????????????????????
When writing a virus, size is a primary concern. A bloated virus carrying
unnecessary baggage will run slower than its optimised counterpart and eat
up more disk space.
Never optimise any code before it works fully, since altering code after
optimisation often messes up the optimisation and, in turn, messes up the
code. After it works, the focus can shift to optimisation. Always keep a
backup of the last working copy of the virus, as optimisation often leads
to improperly working code. With this in mind, a few techniques of
optimisation will be introduced.
There are two types of optimisation: structural and local. Structural
optimisation occurs when shifting the position of code or rethinking and
reordering the functions of the virus shorten its length. A simple example
follows:
check_install:
mov ax,1234h
int 21h
cmp bx,1234h
ret
install_virus:
call check_install
jz exit_install
If this is the only instance that the procedure check_install is called,
the following optimisation may be made:
install_virus:
mov ax,1234h
int 21h
cmp bx,1234h
jz exit_install
The first fragment wastes a total of 4 bytes - 3 for the call and 1 for the
ret. Four bytes may not seem to be worth the effort, but after many such
optimisations, the code size may be brought down significantly. The
reverse of this optimisation, using procedures in lieu of repetitive code
fragments, may work in other instances. Properly designed and well-thought
out code will allow for such an optimisation. Another structural
optimisation:
get attributes
open file read/only
read file
close file
exit if already infected
clear attributes
open file read/write
get file time/date
write new header
move file pointer to end of file
concatenate virus
restore file time/date
close file
restore attributes
exit
Change the above to:
get attributes
clear attributes
open file read/write
read file
if infected, exit to close file
get file time/date
move file pointer to end of file
concatenate virus
move file pointer to beginning
write new header
restore file time/date
close file
restore attributes
exit
By using the second, an open file and a close file are eliminated while
adding only one move file pointer request. This can save a healthy number
of bytes.
Local, or peephole, optimisation is often easier to do than structural
optimisation. It consists of changing individual statements or short
groups of statements to save bytes.
The easiest type of peephole optimisation is a simple replacement of one
line with a functional equivalent that takes fewer bytes. The 8086
instruction set abounds with such possibilities. A few examples follow.
Perhaps the most widespread optimisation, replace:
mov ax,0 ; this instruction is 3 bytes long
mov bp,0 ; mov reg, 0 with any reg = nonsegment register takes 3 bytes
with
xor ax,ax ; this takes but 2 bytes
xor bp,bp ; mov reg, 0 always takes 2 bytes
or even
sub ax,ax ; also takes 2 bytes
sub bp,bp
One of the easiest optimisations, yet often overlooked by novices, is the
merging of lines. As an example, replace:
mov bh,5h ; two bytes
mov bl,32h ; two bytes
; total: four bytes
with
mov bx,532h ; three bytes, save one byte
A very useful optimisation moving the file handle from ax to bx follows.
Replace:
mov bx,ax ; 2 bytes
with
xchg ax,bx ; 1 byte
Another easy optimisation which can most easily applied to file pointer
moving operations:
Replace
mov ax,4202h ; save one byte from "mov ah,42h / mov al,2"
xor dx,dx ; saves one byte from "mov dx,0"
xor cx,cx ; same here
int 21h
with
mov ax,4202h
cwd ; equivalent to "xor dx,dx" when ax < 8000h
xor cx,cx
int 21h
Sometimes it may be desirable to use si as the delta offset variable, as an
instruction involving [si] takes one less byte to encode than its
equivalent using [bp]. This does NOT work with combinations such as
[si+1]. Examples:
mov ax,[bp] ; 3 bytes
mov word ptr cs:[bp],1234h ; 6 bytes
add ax,[bp+1] ; 3 bytes - no byte savings will occur
mov ax,[si] ; 2 bytes
mov word ptr cs:[si],1234h ; 5 bytes
add ax,[si+1] ; 3 bytes - this is not smaller
A somewhat strange and rather specialised optimisation:
inc al ; 2 bytes
inc bl ; 2 bytes
versus
inc ax ; 1 byte
inc bx ; 1 byte
A structural optimisation can also involve getting rid of redundant code.
As a virus related example, consider the infection routine. In few
instances is an error-trapping routine after each interrupt call necessary.
A single "jc error" is needed, say after the first disk-writing interrupt,
and if that succeeds, the rest should also work fine. Another possibility
is to use a critical error handler instead of error checking.
How about this example of optimised code:
mov ax, 4300h ; get file attributes
mov dx, offset filename
int 21h
push dx ; save filename
push cx ; and attributes on stack
inc ax ; ax = 4301h = set file attributes
push ax ; save 4301h on stack
xor cx,cx ; clear attributes
int 21h
...rest of infection...
pop ax ; ax = 4301h
pop cx ; cx = original attributes of file
pop dx ; dx-> original filename
int 21h
Optimisation is almost always code-specific. Through a combination of
restructuring and line replacement, a good programmer can drastically
reduce the size of a virus. By gaining a good feel of the 80x86
instruction set, many more optimisations may be found. Above all, good
program design will aid in creating small viruses.