💾 Archived View for spam.works › mirrors › textfiles › survival › chapt-4.txt captured on 2023-06-16 at 20:40:38.
-=-=-=-=-=-=-
.he CHAPTER 4 CORBIN HANDBOOK AND CATALOG NO. 7, PAGE #
SWAGING IN THE RELOADING PRESS
If your reloading press accepts standard 7/8-14 TPI dies and its
ram will take regular RCBS button-type shell holders, then you can use
it for swaging certain calibers and kinds of bullets with Corbin
reloading press swage dies. A heavy-duty press makes the work easier,
but any modern press capable of resizing a .30-06 case is strong enough
for bullet swaging in the styles and calibers we offer.
There are limits to the pressure you can safely apply to the soft
screw-stock rams used in nearly all current reloading presses. The
size of the frame or leverage of the press has nothing to do with this.
A massive press like the RCBS Big Max still has a four-inch stroke, to
get a magnum rifle case in and out. Small arms bullets, on the other
hand, need only about two inches of stroke in order to be successfully
swaged. This wastes half the leverage in a reloading press.
Single station, ram-type presses are the only kind currently
supported by swaging equipment. Presses with turrets, rotating shell
holder plates, aluminum frames, mechanical type shell holders that
adjust to different size cartridge heads, progressive loaders, and bar-
type rams used in H-frame presses all have features that make some
swaging operations difficult or impossible. Standard swage dies for
reloading presses do not require a massive press, but they do work best
in a simple, single-station conventional round-ram press.
A special swaging press like the Corbin Mity Mite (CSP-1) or a
combination reloading and swaging press like the Corbin Mega Mite (CSP-
2) has the capability to more than double the leverage in a reloading
press design. It does this by cutting the stroke in half. The same
effort that moves a reloading press ram four inches is now put to work
moving the ram only two inches. The effort is converted into higher
pressure within the die.
Such presses have many special features designed to allow higher
stresses, equalize the torque on the ram, align the die and punch more
precisely, and provide for automatic ejection of the bullet on the back
stroke. The die can be designed to withstand higher pressure, since it
doesn't have to fit into the constraint of a standard reloading press
dimension.
In these presses, any caliber from .14 to .458 rifle bullets with
tubing jackets as thick as 30 thousandths of an inch are perfectly
feasible. In a conventional reloading press, you are limited to the
.224, .243, and .257 rifle calibers, and the .25 ACP, .30-32 Handgun
and carbine (130 grains or less, no spitzer rifle shapes), 9mm and
.357/.38 Handgun calibers. Within those calibers, there is
considerable latitude for weight and style variation.
Regardless of the press or system, you can make lead bullets or
gas-checked bullets in any die capable of jacketed bullet swaging. And,
you can use longer or shorter jackets in the same set of dies. There
are some dies made just for lead bullets, combining the steps of core
swaging and core seating so that you can make a lead bullet in one
quick stroke, and these special (model LSWC-1) dies are not generally
suited for use with more than a half-jacket. These dies are not made
for the reloading press, in any case, since they require bleed holes in
the die wall.
Core swage dies and other lead-forming dies that have extrusion
holes through their walls to let you automatically adjust the lead core
weight on each stroke (instead of just using whatever weight of core
you happen to put into the die) need room around the side of the die
for the lead to come out. In a reloading press, the die is put into
the head of the press. Because of the length and top position of the
ram in a reloading press, the die has to be located so its walls are
surrounded by the threads of the press. This doesn't leave room for
correctly located bleed holes.
In order to do it right, core swaging and lead semi-wadcutter dies
that adjust the core as they form the bullet are made only for the
special swaging presses, and not for use in reloading presses. You can
still make lead bullets of equal quality in a reloading press, but to
get there, you must be more careful about how you cut or cast the
cores. What you put into the die is what you get out, in regard to
weight control. This is a major advantage of the special swaging press
systems, and is one of the things that makes it difficult to "convert"
or adapt many of the advanced kinds of dies for use in ordinary
reloading presses.
Reloading press swage dies are made with a UNIVERSAL ADAPTER BODY,
which is the same for all styles and calibers of dies. This component
holds the actual die "insert" and internal punch together in the proper
relationship, and fits into the 7/8-14 TPI threads of your
reloading press. All adjustment for different weights and styles of
bullets is made by turning the whole die, universal adapter and all, up
and down in the threads of the press like a big micrometer thimble.
There are two punches in every swage die. The INTERNAL PUNCH
stays inside the die. It is held there by two restraints: the punch
has a head on the top that won't let it fall through the die on the
"downstroke", or ejection cycle, and the universal adapter body only
lets the punch head slide up a certain distance before it strikes the
top of the hole machined in the adapter. The EXTERNAL PUNCH fits into
the slot in the press ram, just like a shell holder. It can easily be
removed and changed. Most people own several external punches for each
of their die sets.
A small hole goes all the way through the top of the adapter. It
is .257 inches in diameter, and takes a quarter-inch diameter KNOCK-OUT
ROD (also called the ejector rod or simply K.O. rod). The Knock-Out
rod is long enough so that it can push the internal punch down nearly
the same distance as the die is long. That pushes the bullet out the
die mouth. On one end of the Knock-Out rod is a knurled head, big
enough to give you a good target to tap with a plastic mallet or a
piece of wood. This drives the bullet back out of the die after
swaging.
The ejector rod comes completely out of the die, so you can use it
on any of your reloadin press swage dies. Another way to eject bullets
-- one with a little more sophistocation -- is to slip a Corbin POWER
EJECTOR UNIT over the top of the die and fasten the three set-screws
into the ring machined around each of the universal adapter bodies,
right below the knurled part.
The power ejector is an optional accessory item. It speeds up the
operation by eliminating the need to pick up a mallet and tap the
ejector. Instead of using the regular ejector, you install a straight
piece of quarter-inch diameter steel rod, supplied with the PE-1
ejector. Following the instructions that come with this tool, adjust
its ram so that all the free play is taken up when you have a bullet in
the die, ready to be ejected. From this point on, your swaging
operation is reduced to two levers: the press handle swages the
bullet, and the power ejector handle gently but firmly pushes it out of
the die.
The internal punch in your reloading press swage die can be
removed easily. Identify the die insert itself. This is the super-
hard high-carbide alloy steel cylinder at the very bottom of the whole
die assembly, just protruding from the adapter about a quarter inch.
Most of the die insert is up inside the adapter body, which is machined
to accept the 5/8-24 TPI threads on the other end of the die. To
remove the die, grasp the small protruding surface with pair of pliers
and unscrew it. (Don't worry about marring the die -- it is so much
harder and tougher than your pliers that you can't hurt it this way.
On the other hand, don't grasp the oxide-blued adapter body with
pliers: it isn't very hard, and you can damage the threads. Just hold
it in your hand.)
There are basically three dies available for the reloading press
that are swage dies, and several kinds of draw dies. The swage dies
are:
(1) The CORE SEATER
(2) The POINT FORMER
(3) The LEAD TIP DIE
The core seater (CS-1-R designation, in the reloading press
system) can perform two different jobs. It can be used by itself to
make any kind of bullet that has straight, parallel sides, a small
shoulder, and a lead nose from the shoulder up. The whole bullet can
be lead, or any amount of it can be covered by a jacket right up to
that shoulder. Think of a Keith handgun bullet with a jacket coming
right up to the semi-wadcutter shoulder and then stopping. Right up to
this point, the bullet is straight. The jacket can't be curved past
this point in this kind of die alone.
However, the nose can be any shape you like. The nose is formed
by letting the lead core flow down into a cavity machined in the end of
the external punch. You can make a round nose, a Keith nose, a
wadcutter (very little cavity, if any, in the external punch tip!), a
conical nose like a pencil point, or anything else including fancy
multi-cavity hollow points (instead of just a cavity, there is also a
probe or rod in the end of the punch to make these). The point is,
while you can just change the punch to whatever the lead core flow down into a cavity machined in the end of
the external punch. You can make a round nose, a Keith nose, a
wadcutter (very little cavity, if any, in the external punch tip!), a
conical nose like a pencil point, or anything else including fancy
multi-cavity hollow points (instead of just a cavity, there is also a
probe or rod in the end of the punch to make these). The point is,
while you can just change the punch to whatever thickness to its edge,
or it would quickly crumble away. A 0.015 to 0.025 edge thickness is
standard. This small edge comes up against the jacket in our example,
and presses hard on the thin jacket material. One of them has to
buckle and fold. Usually it is the jacket.
If you try to make a semi-wadcutter bullet, and the jacket comes
out with radial folds, much as if someone sat on your top hat, then see
if you have enough lead sticking out the jacket to completely fill up
the cavity in the punch you selected. If not, that's the problem, and
the solution is to use a heavier core, a shorter jacket, or a punch
with less of a cavity. Another solution is to use a hollow point punch
first, moving lead up and out of the jacket, and then form your nose
using the extra amount of lead displaced from inside the jacket.
Let's back up a minute in case anyone is lost at this point. We
are talking about the most basic kind of swage die, the core seating
die. It is called a core seating die because it can be used to seat or
press the core down into a jacket, expanding the core and the jacket
together until they contact the walls of the die. The internal
pressure becomes uniform as soon as the jacket is pushed out against
the die walls evenly, and the base of the jacket comes hard against the
internal punch face. This uniform internal pressure can exceed 20,000
psi (and usually does).
Compressed oxygen gas in a welding tank is in the 2,000 to 3,000
psi range. Compressed air in your car tires is usually 35 to 45 psi.
When you fire a typical rifle, pressures momentarily peak at levels
that reach 25,000 to 55,000 psi typically. The average pressure over a
second of time is vastly lower. The swage die must be able to sustain
anywhere from 20,000 to 50,000 psi constantly, year after year, without
change in its diameter, roundness, straightness. It can't develop a
barrel shape inside, nor can it grow with the continued stress.
Tolerances in a casting mould usually are held to 0.003 to 0.001
inches, plus or minus. Tolerances in the core seating die are usually
held to better than 0.00005 inches, plus or minus! Your bullet doesn't
need to be within that tolerance of some arbitrary standard diameter,
of course, but it is nice to know that whatever diameter it comes out,
it is repeatable to such high precision. The typical absolute diameter
tolerance on the bullet diameter is normally 0.0005 inches plus or
minus, although this has long been proven of little importance, as long
as the variance is held to high precision tolerances.
In other words, if you have a .308 rifle, and you know for sure
that your barrel has a .3000 bore, with all grooves at exactly 0.0040
inch depth, it still doesn't matter nearly as much whether you shoot a
.3079 bullet or a .3090 bullet down that barrel, compared to whether
your bullets vary from one to the next as you try to put them into one
hole. Many competitive shooters find a bullet with nearly 0.001 inch
larger than nominal diameter shoots better at long range than a
conventional "correct" diameter bullet.
In any case, the core seating die is a straight hole die. If you
take it out of the adapter body and pull out the internal punch, you
will be able to see straight through it. The hole is round, straight,
and highly finished. The internal punch is a very close sliding fit.
The external punch can fit the die bore, for making those semi-
wadcutter and wadcutter type bullets, or it can fit inside the jacket
for making rifle-style bullets.
Let me make a definition of these two general kinds of bullets.
It's important to understand what I'm talking about so you can make
proper and cost-effective decisions later on. There are semi-wadcutter
styles, and rifle styles of bullets, relative to the kind of equipment
needed. When a swage die-maker talks about a semi-wadcutter (or
wadcutter) style, it isn't just a specific nose shape. In regard to
the kind of equipment required, it means any bullet that is made with a
lead nose, ending at a small shoulder, and having the jacket at full
bore diameter all the way to the base (if there is any jacket).
This kind of bullet can be made in a single core seating die in
one stroke of the press. One pass -- all done. No lubricating, no
sizing. Just load it and enjoy shooting it. Lead bullets are swaged
with a film of flexible, hard wax bonded to them under swaging
pressure. This is accomplished by dipping the core in a liquid "Dip
Lube", which some people call "liquid jacket", just prior to swaging.
The film evenly covers the bullet, making it usable to speeds of 1,200
fps with no grooves, no separate lubricating steps.
Cup bases? Hollow bases? No problem -- just remove that flat
ended internal punch, and install an optional internal punch with a
probe shaped like the cavity you want to form. Both the nose and base
are formed at the same time, by pressing against the two punches.
Unlke a mould, there is no conflict between hollow bases and hollow
points. They are independent of each other and can be mixed or matched
any way you like. In fact, you can turn the swaged bullet over and
swage it the other direction, perhaps using a little higher setting of
the die to get slightly less penetration of the punch. This gives you
shapes that neither of the punches has by itself, and demonstrates one
of the more powerful experimental features of swaging equipment.
We mentioned seating the core inside the jacket. If you wanted
to, you could select an external punch (the one that slips into the
slotted ram like a shell holder) with a small enough diameter to fit
right inside the jacket. Jackets usually have some taper in the wall
thickness to control expansion. The punch will contact the jacket wall
at some point if it is a close fit. Obviously there are some limits as
to the depth of insertion of any given diameter punch, and to the range
of weights of cores that you could seat with each punch.
If the punch is too small, lead will spurt out around it and you
may not be able to build enough pressure inside the jacket to expand it
properly. This produces undersized and tapered bullets. If the punch
is too large, it may not go into the jacket at all, or it may plow up
jacket material as it presses down. This isn't always bad -- it can be
used to thin the front of the jacket, or to help lock the core into
place. Usually, though, the jacket and punch need to be made for each
other to avoid this. Fortunately, Corbin is the world's largest
supplier of bullet jackets of all types, and can provide the right
punches for any jacket or core weight, as well as the jackets to match.
The reason for seating a core inside the jacket is to make that
second kind of bullet, the rifle-style bullet having the jacket curved
around the ogive, with an open tip. Let's define open tip and hollow
point for bullet swagers. An open tip bullet has the core seated below
the end of the jacket. The jacket extends forward, past the core.
This leaves an opening or an area devoid of lead just below the tip. A
hollow point, on the other hand, is made by pressing a punch with a
projection or probe machined on the end into the core. The hole or
cavity thus formed in the core is further shaped when the ogive is
made. The result is a bullet with a hollow area in the point, formed
in the lead itself.
A hollow point bullet can have a lead tip, or it can have the core
seated down inside the jacket. Usually, it has a lead tip exposed
beyond the end of the jacket. But an open tip bullet can't, by
definition, have a lead tip. The reason to be clear about these terms
is so that when you order tools and punches, everyone will be talking
about the same thing. It makes a big difference whether you can make
what you want once you get the tools. A hollow point is made with an
optional punch, during the core seating stage. An open tip is made by
using a punch that pushes the core down inside the jacket. It is the
standard, "default" design for any regular set of dies that includes
more than a core swage and core seating die. And a lead tip bullet
takes a lead tip forming die in rifle styles, but seldom requires
anything special in the blunt, wide-tip handgun styles.
To make that second kind of bullet, the rifle-style bullet, you
still need the straight-walled core seater. The uniform pressure that
this die produces is necessary to expand the jacket to correct
diameter, mate the core and jacket perfectly, and produce the straight
and round tolerances in the jacket. But with the core seated down
inside the jacket, all you have now is a very accurately formed
cylinder!
To put the ogive (that's OH-JIVE, by the way, like "Oh, don't
gimme no jive, man!") on the bullet, we'll use the second kind of swage
die, the point forming die (designated PF-1-R for reloading press
dies). Now, the term "point" is often confused with the term "tip".
Again, it's nice to talk the same language when ordering parts over the
phone. A point on a bullet refers to anything past the shank or
straight part. A point is the same thing as a nose. The tip, on the
other hand, is just the very end of the point. It is the part that
ends, technically, after the meplat, and begins at some arbitrary place
on the ogive curve that is close enough to the meplat so that it can
have a different curve and not affect the over-all bullet outline
significantly.
Simply put, the tip is the very end of the bullet's nose. The
point is everything from the tip to the start of the straight part
(shank) and the point is the same thing as the nose. To add confusion,
some people even call the point the ogive, so really the terms point,
ogive, and nose all refer to the same thing in general sales talk. But
tip is different.
The ogive is formed by pushing the straight cylinder you made in
the core seating die into the point forming die. It goes in nose
first. If you want the nose to be made on the open end of the jacket,
then the open end goes in first. You can make a solid nose, or full
metal jacket (FMJ, as it is called, though strictly speaking, the open
tip also is a full metal jacket bullet) design by pushing the seated
core and jacket into the point forming die base first. Special notes
on this technique can be found in Corbin technical papers and books.
The point forming die has the actual shape of your bullet frozen
in tough die steel, diamond lapped to extremely fine finish and
tolerance by skilled die-makers. It is a hand-made die, produced by
craftsmen with years of experience. It isn't much like a punch press
die or a plastic moulding die, and people who have skills in those
fields usually can't produce good point forming dies without a great
deal more training.
To make this die, both reamers and laps have to be cut to
precisely the right shape and diameter for your desired bullet. In
reloading press equipment, the great attraction is the lower cost since
you can use an existing press. If your main goal is economy, then it
doesn't help that goal to increase the cost of the dies by adding extra
labor, so we manufacture only standard shapes and offer no custom work
in the reloading press line. By doing this, we have been able to
produce swage dies superior to those costing ten times as much, that
are made to special order. Corbin makes the only serious attempt at
mass production of hand-crafted swage dies: by eliminating all the
stages of custom fitting and tooling, we've been able to bring swaging
equipment of high quality to every corner of the earth, and introduce
thousands of people to swaging who could not otherwise afford to try
it.
If you want custom shapes and diameter, on the other hand, then we
do have another system set up to handle it at reasonable cost. In
fact, this system is designed on two levels: semi-custom and fully
custom work using the same basic equipment. The advantage is that we
can use all standard blanks, that fit into standard presses and use the
same general parts. Your cost is lower, your replacements or repairs
are much simpler, and the whole system is so well proven it has become
the world's defacto standard for swaging. It's called the Mity Mite
system, and we'll discuss it shortly. Semi-custom outfits can be
obtained by selecting from the wide variety of off-the-shelf components
kept in moderate supply for immediate delivery. Fully custom outfits
can be produced, subject to the usual waiting list.
In the reloading press, the point forming die is built very much
like the core seating die. It fits the same universal adapter body, so
both dies look almost identical from the outside. The difference is
easy to tell: push on the ejector rod. The core seating die has no
internal spring. The ejector rod will slide the internal punch down
and you'll see it at the mouth of the die. The point forming die has a
small (0.080") spring-steel wire pin passing through the tip of the
cavity. This pin is a press fit into a steel button "head". The head
is machined to go into one end of a coil spring.
The spring presses between the top of the die and the head of the
ejection pin. We call the internal punch an ejection pin. The heavy
rod that pushes on it is called the ejection rod, you'll recall. If
you order a new ejection rod, you'll get this quarter-inch diameter rod
with the knurled head. If you order a new ejection pin, we'll want to
know the diameter of wire, or at least what caliber of die it fits.
The reason for having a spring in this die is to hold the pin out
of the main part of the die cavity during bullet swaging. The only
purpose of the ejection pin is to push the bullet out of the die by its
nose. If the pin were down in the cavity, the bullet would form up
around the pin, and then it would be stuck in the bullet. This is
exactly what happens if you forget to use lubricant. Now it's time to
mention a very important part of swaging: the correct lube.
For lead bullets, you have seen that a wax solution called Dip
Lube can be applied before swaging the core. For jacketed bullets, a
different kind of lube, serving a totally different purpose, is
required. Swage lube is made to stand up to extreme pressures without
losing its protective film -- a barrier between the smoothly finished
die wall and the moving jacket material. Ordinary case lubes are
useless. Don't try them. Swage lube is a little more expensive, but
it goes a long way and it works. Your dies will last virtually forever
if you use the right lube and clean materials.
Every component needs a thin film of lube applied before it goes
into the die. Lead or jacket, there must be a film of lube between it
protective film -- a barrier between the smoothly finished
die wall and the moving jacket material. Ordinary case lubes are
useless. Don't try them. Swage lube is a little more expensive, but
it goes a long way and it works. Your dies will last virtually forever
if you use the right lube and clean materials.
Every component needs a thin film of lube applied before it goes
into the die. Lead or jacket, there must be a film of lube between it
You simply press
the seated core in (using proper lube), and eject the final bullet out.
The bullet goes in nose first, pressed in with an external punch that
is as big as the bullet base. It comes out base first, pressed out by
a tiny ejection pin that bears on the tip of the bullet. The reason
you cannot form the complete bullet in one stroke in this die is that
the pressure required to expand the jacket uniformly is not present in
this kind of die. There are two exceptions. You can make a full metal
jacket bullet in this die alone. And you can make a lead bullet.
The techniques for FMJ styles are discussed in other books. Lead
bullets are simply a matter of shoving the lead into the die. It has
to be smaller than the die cavity, naturally. Everything about swaging
assumes you know better than to push a larger component into a smaller
die cavity. The match between core seating die and point forming die
is very good. For many years, bullet makers thought that it was
necessary and desirable to have a slight pressure ring at the bottom of
the bullet. This "pressure ring", as it was called, was promoted as
increasing accuracy by many die-makers of the 1950's. It may not hurt
accuracy at all, and it could help in some cases.
In reality, though, the story is a little different. Most die-
makers of the past worked at home or in very small shops, and didn't
have the money for really expensive, high-precision instruments to
measure the bore sizes of the dies as they were being produced. As a
result, a match of 0.002 to 0.0008 inches between core seat and point
form die cavities was about all the die-makers could manage. Even
today, that is typical of the best amateur work and is seen in some of
the higher priced benchrest dies as well.
Because of this difference, the seated core and jacket always went
into the point forming die considerably under final diameter. The
pressure of swaging the point expanded the jacket slightly, but most of
the expansion took place at the base. These bullets won a lot of
matches, but they still had a bit of taper and a bulge at the base.
The die-makers, not knowing how to get rid of it, and noticing that
even with this defect, the bullets still outshot most factory slugs,
started hinting that maybe this was really a design feature put in by
plan, instead of something they hadn't yet acquired the tools to
eliminate.
Today, we still run into a number of precision shooters who read
the old literature and come to believe that a "pressure ring" is
necessary for good shooting. I don't think that having a 0.001-inch
larger base is harmful to accuracy, but I don't think it necessarily
does anything valuable. On the other hand, a bullet that is up to
0.001-inch larger than standard size, and straight, is probably going
to be a good shooter and it won't expand the case neck as it is seated,
then leave the case somewhat loose on the forward part of the bullet.
With much taper on the bullet, the act of feeding the round can push
the bullet back into the powder, and I know that won't help accuracy.
We can make bullets tapered, straight, or with a pressure ring.
In the reloading press, we don't offer a choice. In general, it is one
of those features that is best left to the die-maker, since
specification of too many "nit-picking" details only runs up your cost
for special charges on the die-maker's labor, and doesn't give you any
more accurate bullet one way or the other. But, if you need something
very special in this regard, it is one more thing that has been pinned
down and can be offered to anyone who feels it is worth the extra
expense.
The core seating die has made us some semi-wadcutters and seated
some cores for rifle-style bullets (I say rifle style because they
could just as well be .32 handgun bullets or .243 rifle bullets -- it
is exactly the same process, same kind of die, and the only difference
is the size of the hole and the size of the components going into it).
We have used the point forming die to shape the rifle-style bullet by
forming the ogive, and in two steps we have made nice open tip bullets.
What about lead tips and hollow points? The hollow point is made
by seating the core with a hollow point punch, then forming the ogive.
If the hollow point is also a lead tip, then the lead is longer than
the jacket. Trying to eject this bullet may cause some deformation of
the tip, since the ejection pin has to push on the tip with some force.
The third die we mentioned (lead tip die) is made to finish off the tip
so it looks as good as or better than factory bullets.
The lead tip die (designated LT-1-R for the reloading press) is
much like the core seating die, except that it has a slightly larger
bore size, and the internal punch has a cavity that matches the ogive
in the point form die. The deformed lead tip fits up inside this
cavity. Applying gentle pressure reshapes the lead tip, shears off any
surplus lead, and leaves a fine looking lead tip that can be flat,
sharp, or radiused. The lead tip die is a nice addition to any set,
giving you the ability to reform the tips and even to close the open
tip more tightly than you can do it in the point forming die alone.
The smallest tip opening is the same diameter as the ejection pin
in the point form die. This ejection pin has to be strong enough to
push the bullet out of your die, or you will be constantly replacing
the ejection pins and having stuck bullets. So, a diameter of about
0.080-inch is used in reloading press sets. This is a good compromise
between design strenght and appearance. You can close the tip even
further by using the lead tip die carefully. This takes a little
practice to avoid pressing a little shoulder in the ogive, but once you
figure it out, it is easily repeated.
How do you know how hard to push on the handle? Just push a
little bit, very lightly. See if the jacket and core remain in the
core seating die, or if they come back with the punch. Normally, the
correct pressure just expands the jacket enough so that it stays up in
the die. In point forming, use just enough pressure to form the bullet
until you start to get a parallel pipe of jacket or lead on the tip
(pushing the bullet material up into the ejection pin hole). That is as
far as you can expect to go. Back off slightly on the die adjustment
by raising it higher a half turn or so in the press, and you can then
use the full ram stroke to set your insertion depth each time.
One key to uniform swaging in the reloading press is to use the
top of the stroke, so that each time you move the press handle, you are
using the physical limit of the press to control how far the punch
inserts into the die. This controls amount of hollow cavity, the degree
to which you reshape a bullet, the amount of tip closure on your ogive,
and whether or not you are going to get a good lead tip. Everything
depends on uniform stroke, uniform insertion of the punch. And that is
most easily set by raising the die, so that the ram goes as far up as
it can. Then lower the die, to obtain the desired shape or insertion.
The right pressure should be about like sizing a case. The larger
the caliber, the more pressure you will feel on the handle. In no case
is it necessary to throw your weight on the handle, or break your
loading bench, or use a cheater bar. Doing these things will quickly
make the die-makers more wealthy, because you will soon break your die
and mash your punches into pancakes, requiring that you replace them.
If you feel generous toward die-makers this week, by all means jump up
and down on the press handle a few times. Otherwise, a mild one-hand
force is quite enough.
Another point in regard to destruction of parts: always try a
punch by hand first. If it won't fit, wipe it off several times with a
clean cloth, oil it lightly, and try again. If it still won't fit,
make sure that you have the right punch! Punches must fit closely but
with relative ease into the dies. Keith nose punches, and others with
deep cavities, expand slightly and may not fit easily by hand after
they have been used. But they do fit, given a little oil and a little
gentle pressure. I have seen .242-inch diameter rifle punches (for the
6mm point forming die) pushed into a .2238-inch diameter hole in the
.22 core seating die. "I thought it went in a little hard," the
bullet-maker said. Yes, I guess it might. Comes out a little hard,
too. Try it by hand first.
The slot in the reloading press ram collects primer residue and
metal shavings. Take a cotton swab or a wood pick and scrape it out
before installing your bullet swage punch. The material stuck in the
slot can tip the punch, causing it to ram into the die at an angle and
tear a nasty gouge all down the side of the punch. Again, be gentle
when you first start out. Don't use speed or force on the first
stroke, but instead, gently guide things together and notice how they
fit. Then go after it, once you know everything is lined up.
Making .22 caliber bullets out of rimfire cases is one of the most
popular swaging activities today for a reloading press bullet-maker.
It has been so for twenty years. The process takes three steps. Draw
the jackets, seat the cores, and form the points. Lead tip bullets add
a further step of forming the tips. Detailed instructions come with
the die sets, and further information is found in the various technical
bulletins and text books we publish.
The photos in this book will give you a good idea of how the
process works. The most questions are about annealing and cleaning .22
cases. First, annealing is usually done after boiling in hot soapy
water and vinegar (to clean and shine the brass). Annealing is only so
that the ogive will form without any folding. If you make a big lead
tip, you probably can avoid annealing. There are several ways to go
about it. Putting a group of clean cases in a tuna can, inside a lead
pot, and letting them turn dark brown (15 minutes, usually) will do it.
Using a toaster oven on high, or putting a pan of cases in a self-
cleaning oven for the duration of the self-clean cycle is also good.
Using a propane torch or electric heat gun (Corbin FHG-1) is also good,
primarily for smaller lots.
The older books suggested 600 to 650 degrees F. I have found that
modern cases take 800 to 900 degrees F., and that a standard electric
oven doesn't usually get hot enough. We do make excellent quality heat
treatment furnaces, but for the hobbyist they are too expensive. The
time and quench after heating are not critical. Quenching has no
effect on the hardness. It merely helps to knock of any scale
that might have formed. If you use the right temperature, you won't
get any scale, and you can forget about any quench. Just let the cases
air cool. Use swage lube on the punch when you draw the jackets. Just
slip them over the long, 0.2-inch diameter punch and push them into the
die, following instructions provided with the tool.
Rimfire cases are good to about 3,000 or 3,200 fps before they
start to come apart. Actual speed depends on rifling depth and
sharpness. They force you to load a .22-250 down to .222 Mag velocity,
but on the other hand, they also make you save powder, barrel, and cost
nothing for material. When they hit, you'd swear they were going over
4,000 fps compared to a factory bullet performance. And there is no
problem with barrel fouling or wear: if anything, the thinner jackets
are easier on your gun than a standard bullet. Try it! You will be
surprised at the accuracy.