💾 Archived View for spam.works › mirrors › textfiles › anarchy › mism5.hac captured on 2023-06-14 at 15:40:19.
-=-=-=-=-=-=-
GENERAL REACTOR DESIGN
Nuclear Reactors are powered by fission. Fission was first discovered by Hahn
and Strassmann in Germany by bombarding the uranium nucleaus with neutrons. It
would follow that if there were neutrons among the products of fission, then
they could produce additional fissions and a chain-reaction might result.
Fermi, the leading nuclear physicist of the time decided to look into the
matter. It was found (by Bohr & Wheeler) that U235 produced fission more
readily than U238. The hard part in getting the pile to work is what is
called the reproductive factor. A chain reaction can only occur if the number
of neutrons emmited in fission is greater than one. If the number was one,
then no chain reaction would occur. If two were emitted, then a geometric
progression could be created that would lead to a "chain-reaction". Now this
is complicated by the fact that when the neutrons leave the nucleus, they are
moving very fast. In order to promote fission, it is necessary to have slow
moving neutrons. So we get back to the hard part: It is necessary to have a
reproductive factor that after slowing, is greater than one. Obviously, the
larger the reproductive factor, the larger the reaction (very large
reproduction factors will cause a rather large boom). To complicate matters,
the "free path" of the neutron, or the average distance it travels before
being absorbed by the nucleus, is long and if you can't keep the neutron from
escaping the uranium, then no reaction. To overcome the problem, a lattice of
uranium cells could be "piled" on top of one another in order to promote the
reaction. (Hence: Chain-Reacting Pile) The pile consists of slugs of pure
Uranium arranged in a space lattice embedded in a matrix of graphite. The
slugs could be referred to as "fuel rods". The Graphite is used to slow the
nuetrons down, and something like boron steel (control rods) is capable of
being inserted to help control the neutron flux. Boron steel & cadmium both
absorb neutrons.
The amount of energy that any neutron gets in the reaction is a matter of
chance, and a due to technical problems, the game of slowing down and catching
neutrons can be very tricky. If the neutron is moving too fast to be captured
by the uranium nucleus, then it just bounces off in what is known as an
"inelastic collision". In this event essentially no speed is lost. But if
the neutron strikes a material of small atomic weight, such as carbon
(graphite), then an "elastic colision" occurs where the graphite particle
absorbs energy, and the neutron slows down. It takes about 15 collisions with
carbon to slow the neutron down by a factor of 10. This would mean that about
110 such collisions are needed in order to bring a 1,000,000-volt neutron down
to "thermal energy" or about 1/40 of a volt.
The "collision cross section" for cadmium is about 10E-24 centimeters, or one
barn. This is very large in atomic terms and makes hitting the cadmium as
easy as "hitting a barn". The collision cross section for carbon is only
about one five thousandths of a barn. Now the De Broglie wavelength of a
particle gets bigger as its speed gets smaller, so as the neutron gets
smaller, it sort of spreads out and has a greater chance of hitting the
nuclei. (or one might say that its capture cross section gets larger as its
velocity decreases. Of course nuetrons can get lost, be absorbed by the
carbon, or mutate the uranium into another isotope (resonance absorbsion). The
losses must be taken into consideration when calculating the reproductive
factor. The proportions of carbon and uranium must be precisely controlled in
order to get a chain reaction.
If you have a homogenous mixture, then on the average every second nuclei will
be a uranium one and the neutrons will never slow down enough and be lost due
to reasonance absorbtion. To get around this, a "lumpy" mixture is used in
the pile. A neutron has to get through a lump of carbon (slowing it down) and
if one doesn't hit enough carbon, it will mutate only the outer layer of the
U235 lump, leaving the rest O.K.
Anyway, take a lattice cell (cube) of 8.25 inches per side. (composed of U
metal and UO2 imbedded in graphite. Pile them in approximately a flattened
rotational ellipsoid with a polar radius of 121 inches, and an equatorial
radius of 153 inches. Support the bugger with a wooden frame, (oh, you'll need
about six tons for this, a small pile. Larger piles yield larger reproduction
factors.) and you have it. You should have a reproduction factor of about
1.067. Each metal lump should weigh about six lbs. (available from
Westinghouse, Metal Hydrides, and Ames) Lumps of about seven or eight pounds
would give a better reprodution factor, but would increase the amount of U
metal needed. Each lump UO2 should weigh about 4.71 lbs. Diferent piles can
be mixed together, but put your best materials near the middle. Layer the
graphite bearing Uranium alternating it with graphite. Ordinary wood working
machines can be used to to shape & smooth the graphite to specs. (Graphite can
be obtained from Nat'l Carbon, Speer Graphite, U.S. Graphite, I would suggest
about 14 tons, or 40,000 bricks) In order to press the uranium dioxide lumps,
any good hydrolic press will do. Make sure that the die is made from a good
quality tool steel, hardened and polished. Stearic acid can be used as a
lubricant (0.5% diluted in acetone) with ethylene glycol added as a wetting
agent. You'll need about 150 to 175lbs of pressure. As long as you are
careful you can use different forms of uranium and graphite and still get a
good pile. I'd suggest surrounding the entire thing with a neutron absorbing
material such as cadmium. Once you get it up, pull out all of the control rods
but one (one is all you need on a small pile anyway). Remove the last one
slowly till it is about halfway out. check your neutron detectors and pull it
out slowly (a geometric reaction starts slow, buts will pick up speed), until
you get the output that you wish.