💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc1514.txt captured on 2023-05-24 at 21:18:50.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group P. Grillo
Request for Comments: 1514 Network Innovations
Intel Corporation
S. Waldbusser
Carnegie Mellon University
September 1993
Host Resources MIB
Status of this Memo
This RFC specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" for the standardization state and status
of this protocol. Distribution of this memo is unlimited.
Abstract
This memo defines a MIB for use with managing host systems. The term
"host" is construed to mean any computer that communicates with other
similar computers attached to the internet and that is directly used
by one or more human beings. Although this MIB does not necessarily
apply to devices whose primary function is communications services
(e.g., terminal servers, routers, bridges, monitoring equipment),
such relevance is not explicitly precluded. This MIB instruments
attributes common to all internet hosts including, for example, both
personal computers and systems that run variants of Unix.
Table of Contents
1. The Network Management Framework ...................... 2
2. Host Resources MIB .................................... 3
3. Definitions ........................................... 3
4.1 Textual Conventions .................................. 3
4.2 The Host Resources System Group ...................... 5
4.3 The Host Resources Storage Group ..................... 6
4.4 The Host Resources Device Group ...................... 10
4.5 The Host Resources Running Software Group ............ 25
4.6 The Host Resources Running Software Performance
Group ................................................ 27
4.7 The Host Resources Installed Software Group .......... 29
5. References ............................................ 31
6. Acknowledgments ....................................... 32
7. Security Considerations ............................... 32
8. Authors' Addresses .................................... 33
Grillo & Waldbusser [Page 1]
RFC 1514 Host Resources MIB September 1993
1. The Network Management Framework
The Internet-standard Network Management Framework consists of three
components. They are:
STD 16, RFC 1155 [1] which defines the SMI, the mechanisms used
for describing and naming objects for the purpose of management.
STD 16, RFC 1212 [2] defines a more concise description mechanism,
which is wholly consistent with the SMI.
STD 17, RFC 1213 [3] which defines MIB-II, the core set of managed
objects for the Internet suite of protocols.
STD 15, RFC 1157 [4] which defines the SNMP, the protocol used for
network access to managed objects.
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Within a given MIB module,
objects are defined using STD 16, RFC 1212's OBJECT-TYPE macro. At a
minimum, each object has a name, a syntax, an access-level, and an
implementation-status.
The name is an object identifier, an administratively assigned name,
which specifies an object type. The object type together with an
object instance serves to uniquely identify a specific instantiation
of the object. For human convenience, we often use a textual string,
termed the object descriptor, to also refer to the object type.
The syntax of an object type defines the abstract data structure
corresponding to that object type. The ASN.1[5] language is used for
this purpose. However, RFC 1155 purposely restricts the ASN.1
constructs which may be used. These restrictions are explicitly made
for simplicity.
The access-level of an object type defines whether it makes "protocol
sense" to read and/or write the value of an instance of the object
type. (This access-level is independent of any administrative
authorization policy.)
The implementation-status of an object type indicates whether the
object is mandatory, optional, obsolete, or deprecated.
Grillo & Waldbusser [Page 2]
RFC 1514 Host Resources MIB September 1993
2. Host Resources MIB
The Host Resources MIB defines a uniform set of objects useful for
the management of host computers. Host computers are independent of
the operating system, network services, or any software application.
The Host Resources MIB defines objects which are common across many
computer system architectures.
In addition, there are objects in MIB-II [3] which also provide host
management functionality. Implementation of the System and Interfaces
groups is mandatory for implementors of the Host Resources MIB.
3. Definitions
HOST-RESOURCES-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE FROM RFC-1212
DisplayString FROM RFC1213-MIB
TimeTicks,
Counter, Gauge FROM RFC1155-SMI;
host OBJECT IDENTIFIER ::= { mib-2 25 }
hrSystem OBJECT IDENTIFIER ::= { host 1 }
hrStorage OBJECT IDENTIFIER ::= { host 2 }
hrDevice OBJECT IDENTIFIER ::= { host 3 }
hrSWRun OBJECT IDENTIFIER ::= { host 4 }
hrSWRunPerf OBJECT IDENTIFIER ::= { host 5 }
hrSWInstalled OBJECT IDENTIFIER ::= { host 6 }
-- textual conventions
-- a truth value
Boolean ::= INTEGER { true(1), false(2) }
-- memory size, expressed in units of 1024bytes
KBytes ::= INTEGER (0..2147483647)
-- This textual convention is intended to identify the manufacturer,
-- model, and version of a specific hardware or software product.
-- It is suggested that these OBJECT IDENTIFIERs are allocated such
-- that all products from a particular manufacturer are registered
-- under a subtree distinct to that manufacturer. In addition, all
Grillo & Waldbusser [Page 3]
RFC 1514 Host Resources MIB September 1993
-- versions of a product should be registered under a subtree
-- distinct to that product. With this strategy, a management
-- station may uniquely determine the manufacturer and/or model of a
-- product whose productID is unknown to the management station.
-- Objects of this type may be useful for inventory purposes or for
-- automatically detecting incompatibilities or version mismatches
-- between various hardware and software components on a system.
ProductID ::= OBJECT IDENTIFIER
-- unknownProduct will be used for any unknown ProductID
-- unknownProduct OBJECT IDENTIFIER ::= { 0 0 }
-- For example, the product ID for the ACME 4860 66MHz clock doubled
-- processor might be:
-- enterprises.acme.acmeProcessors.a4860DX2.MHz66
-- A software product might be registered as:
-- enterprises.acme.acmeOperatingSystems.acmeDOS.six(6).one(1)
DateAndTime ::= OCTET STRING (SIZE (8 | 11))
-- A date-time specification for the local time of day.
-- This data type is intended to provide a consistent
-- method of reporting date information.
--
-- field octets contents range
-- _____ ______ ________ _____
-- 1 1-2 year 0..65536
-- (in network byte order)
-- 2 3 month 1..12
-- 3 4 day 1..31
-- 4 5 hour 0..23
-- 5 6 minutes 0..59
-- 6 7 seconds 0..60
-- (use 60 for leap-second)
-- 7 8 deci-seconds 0..9
-- 8 9 direction from UTC "+" / "-"
-- (in ascii notation)
-- 9 10 hours from UTC 0..11
-- 10 11 minutes from UTC 0..59
--
-- Note that if only local time is known, then
-- timezone information (fields 8-10) is not present.
InternationalDisplayString ::= OCTET STRING
-- This data type is used to model textual information in some
-- character set. A network management station should use a local
-- algorithm to determine which character set is in use and how it
-- should be displayed. Note that this character set may be encoded
-- with more than one octet per symbol, but will most often be NVT
Grillo & Waldbusser [Page 4]
RFC 1514 Host Resources MIB September 1993
-- ASCII.
-- The Host Resources System Group
--
-- Implementation of this group is mandatory for all host systems.
hrSystemUptime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The amount of time since this host was last
initialized. Note that this is different from
sysUpTime in MIB-II [3] because sysUpTime is the
uptime of the network management portion of the
system."
::= { hrSystem 1 }
hrSystemDate OBJECT-TYPE
SYNTAX DateAndTime
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The host's notion of the local date and time of
day."
::= { hrSystem 2 }
hrSystemInitialLoadDevice OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The index of the hrDeviceEntry for the device from
which this host is configured to load its initial
operating system configuration."
::= { hrSystem 3 }
hrSystemInitialLoadParameters OBJECT-TYPE
SYNTAX InternationalDisplayString (SIZE (0..128))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object contains the parameters (e.g. a
pathname and parameter) supplied to the load device
when requesting the initial operating system
configuration from that device."
::= { hrSystem 4 }
Grillo & Waldbusser [Page 5]
RFC 1514 Host Resources MIB September 1993
hrSystemNumUsers OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of user sessions for which this host is
storing state information. A session is a
collection of processes requiring a single act of
user authentication and possibly subject to
collective job control."
::= { hrSystem 5 }
hrSystemProcesses OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of process contexts currently loaded or
running on this system."
::= { hrSystem 6 }
hrSystemMaxProcesses OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum number of process contexts this system
can support. If there is no fixed maximum, the
value should be zero. On systems that have a fixed
maximum, this object can help diagnose failures
that occur when this maximum is reached."
::= { hrSystem 7 }
-- The Host Resources Storage Group
--
-- Implementation of this group is mandatory for all host systems.
-- Registration for some storage types, for use with hrStorageType
hrStorageTypes OBJECT IDENTIFIER ::= { hrStorage 1 }
hrStorageOther OBJECT IDENTIFIER ::= { hrStorageTypes 1 }
hrStorageRam OBJECT IDENTIFIER ::= { hrStorageTypes 2 }
-- hrStorageVirtualMemory is temporary storage of swapped
-- or paged memory
hrStorageVirtualMemory OBJECT IDENTIFIER ::= { hrStorageTypes 3 }
hrStorageFixedDisk OBJECT IDENTIFIER ::= { hrStorageTypes 4 }
hrStorageRemovableDisk OBJECT IDENTIFIER ::= { hrStorageTypes 5 }
hrStorageFloppyDisk OBJECT IDENTIFIER ::= { hrStorageTypes 6 }
Grillo & Waldbusser [Page 6]
RFC 1514 Host Resources MIB September 1993
hrStorageCompactDisc OBJECT IDENTIFIER ::= { hrStorageTypes 7 }
hrStorageRamDisk OBJECT IDENTIFIER ::= { hrStorageTypes 8 }
hrMemorySize OBJECT-TYPE
SYNTAX KBytes
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The amount of physical main memory contained by
the host."
::= { hrStorage 2 }
hrStorageTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrStorageEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of logical storage areas on
the host.
An entry shall be placed in the storage table for
each logical area of storage that is allocated and
has fixed resource limits. The amount of storage
represented in an entity is the amount actually
usable by the requesting entity, and excludes loss
due to formatting or file system reference
information.
These entries are associated with logical storage
areas, as might be seen by an application, rather
than physical storage entities which are typically
seen by an operating system. Storage such as tapes
and floppies without file systems on them are
typically not allocated in chunks by the operating
system to requesting applications, and therefore
shouldn't appear in this table. Examples of valid
storage for this table include disk partitions,
file systems, ram (for some architectures this is
further segmented into regular memory, extended
memory, and so on), backing store for virtual
memory (`swap space').
This table is intended to be a useful diagnostic
for `out of memory' and `out of buffers' types of
failures. In addition, it can be a useful
performance monitoring tool for tracking memory,
disk, or buffer usage."
Grillo & Waldbusser [Page 7]
RFC 1514 Host Resources MIB September 1993
::= { hrStorage 3 }
hrStorageEntry OBJECT-TYPE
SYNTAX HrStorageEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry for one logical storage area
on the host. As an example, an instance of the
hrStorageType object might be named
hrStorageType.3"
INDEX { hrStorageIndex }
::= { hrStorageTable 1 }
HrStorageEntry ::= SEQUENCE {
hrStorageIndex INTEGER,
hrStorageType OBJECT IDENTIFIER,
hrStorageDescr DisplayString,
hrStorageAllocationUnits INTEGER,
hrStorageSize INTEGER,
hrStorageUsed INTEGER,
hrStorageAllocationFailures Counter
}
hrStorageIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for each logical storage area
contained by the host."
::= { hrStorageEntry 1 }
hrStorageType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of storage represented by this entry."
::= { hrStorageEntry 2 }
hrStorageDescr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A description of the type and instance of the
storage described by this entry."
Grillo & Waldbusser [Page 8]
RFC 1514 Host Resources MIB September 1993
::= { hrStorageEntry 3 }
hrStorageAllocationUnits OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The size, in bytes, of the data objects allocated
from this pool. If this entry is monitoring
sectors, blocks, buffers, or packets, for example,
this number will commonly be greater than one.
Otherwise this number will typically be one."
::= { hrStorageEntry 4 }
hrStorageSize OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The size of the storage represented by this entry,
in units of hrStorageAllocationUnits."
::= { hrStorageEntry 5 }
hrStorageUsed OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The amount of the storage represented by this
entry that is allocated, in units of
hrStorageAllocationUnits."
::= { hrStorageEntry 6 }
hrStorageAllocationFailures OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of requests for storage represented by
this entry that could not be honored due to not
enough storage. It should be noted that as this
object has a SYNTAX of Counter, that it does not
have a defined initial value. However, it is
recommended that this object be initialized to
zero."
::= { hrStorageEntry 7 }
Grillo & Waldbusser [Page 9]
RFC 1514 Host Resources MIB September 1993
-- The Host Resources Device Group
--
-- Implementation of this group is mandatory for all host systems.
--
-- The device group is useful for identifying and diagnosing the
-- devices on a system. The hrDeviceTable contains common
-- information for any type of device. In addition, some devices
-- have device-specific tables for more detailed information. More
-- such tables may be defined in the future for other device types.
-- Registration for some device types, for use with hrDeviceType
hrDeviceTypes OBJECT IDENTIFIER ::= { hrDevice 1 }
hrDeviceOther OBJECT IDENTIFIER ::= { hrDeviceTypes 1 }
hrDeviceUnknown OBJECT IDENTIFIER ::= { hrDeviceTypes 2 }
hrDeviceProcessor OBJECT IDENTIFIER ::= { hrDeviceTypes 3 }
hrDeviceNetwork OBJECT IDENTIFIER ::= { hrDeviceTypes 4 }
hrDevicePrinter OBJECT IDENTIFIER ::= { hrDeviceTypes 5 }
hrDeviceDiskStorage OBJECT IDENTIFIER ::= { hrDeviceTypes 6 }
hrDeviceVideo OBJECT IDENTIFIER ::= { hrDeviceTypes 10 }
hrDeviceAudio OBJECT IDENTIFIER ::= { hrDeviceTypes 11 }
hrDeviceCoprocessor OBJECT IDENTIFIER ::= { hrDeviceTypes 12 }
hrDeviceKeyboard OBJECT IDENTIFIER ::= { hrDeviceTypes 13 }
hrDeviceModem OBJECT IDENTIFIER ::= { hrDeviceTypes 14 }
hrDeviceParallelPort OBJECT IDENTIFIER ::= { hrDeviceTypes 15 }
hrDevicePointing OBJECT IDENTIFIER ::= { hrDeviceTypes 16 }
hrDeviceSerialPort OBJECT IDENTIFIER ::= { hrDeviceTypes 17 }
hrDeviceTape OBJECT IDENTIFIER ::= { hrDeviceTypes 18 }
hrDeviceClock OBJECT IDENTIFIER ::= { hrDeviceTypes 19 }
hrDeviceVolatileMemory OBJECT IDENTIFIER ::= { hrDeviceTypes 20 }
hrDeviceNonVolatileMemory OBJECT IDENTIFIER ::= { hrDeviceTypes 21 }
hrDeviceTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrDeviceEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of devices contained by the
host."
::= { hrDevice 2 }
hrDeviceEntry OBJECT-TYPE
SYNTAX HrDeviceEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry for one device contained by
Grillo & Waldbusser [Page 10]
RFC 1514 Host Resources MIB September 1993
the host. As an example, an instance of the
hrDeviceType object might be named hrDeviceType.3"
INDEX { hrDeviceIndex }
::= { hrDeviceTable 1 }
HrDeviceEntry ::= SEQUENCE {
hrDeviceIndex INTEGER,
hrDeviceType OBJECT IDENTIFIER,
hrDeviceDescr DisplayString,
hrDeviceID ProductID,
hrDeviceStatus INTEGER,
hrDeviceErrors Counter
}
hrDeviceIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for each device contained by the
host. The value for each device must remain
constant at least from one re-initialization of the
agent to the next re-initialization."
::= { hrDeviceEntry 1 }
hrDeviceType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An indication of the type of device.
If this value is `hrDeviceProcessor { hrDeviceTypes
3 }' then an entry exists in the hrProcessorTable
which corresponds to this device.
If this value is `hrDeviceNetwork { hrDeviceTypes 4
}', then an entry exists in the hrNetworkTable
which corresponds to this device.
If this value is `hrDevicePrinter { hrDeviceTypes 5
}', then an entry exists in the hrPrinterTable
which corresponds to this device.
If this value is `hrDeviceDiskStorage {
hrDeviceTypes 6 }', then an entry exists in the
hrDiskStorageTable which corresponds to this
device."
Grillo & Waldbusser [Page 11]
RFC 1514 Host Resources MIB September 1993
::= { hrDeviceEntry 2 }
hrDeviceDescr OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A textual description of this device, including
the device's manufacturer and revision, and
optionally, its serial number."
::= { hrDeviceEntry 3 }
hrDeviceID OBJECT-TYPE
SYNTAX ProductID
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The product ID for this device."
::= { hrDeviceEntry 4 }
hrDeviceStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
running(2),
warning(3),
testing(4),
down(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current operational state of the device
described by this row of the table. A value
unknown(1) indicates that the current state of the
device is unknown. running(2) indicates that the
device is up and running and that no unusual error
conditions are known. The warning(3) state
indicates that agent has been informed of an
unusual error condition by the operational software
(e.g., a disk device driver) but that the device is
still 'operational'. An example would be high
number of soft errors on a disk. A value of
testing(4), indicates that the device is not
available for use because it is in the testing
state. The state of down(5) is used only when the
agent has been informed that the device is not
available for any use."
::= { hrDeviceEntry 5 }
Grillo & Waldbusser [Page 12]
RFC 1514 Host Resources MIB September 1993
hrDeviceErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of errors detected on this device. It
should be noted that as this object has a SYNTAX
of Counter, that it does not have a defined
initial value. However, it is recommended that
this object be initialized to zero."
::= { hrDeviceEntry 6 }
hrProcessorTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrProcessorEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of processors contained by
the host.
Note that this table is potentially sparse: a
(conceptual) entry exists only if the correspondent
value of the hrDeviceType object is
`hrDeviceProcessor'."
::= { hrDevice 3 }
hrProcessorEntry OBJECT-TYPE
SYNTAX HrProcessorEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry for one processor contained
by the host. The hrDeviceIndex in the index
represents the entry in the hrDeviceTable that
corresponds to the hrProcessorEntry.
As an example of how objects in this table are
named, an instance of the hrProcessorFrwID object
might be named hrProcessorFrwID.3"
INDEX { hrDeviceIndex }
::= { hrProcessorTable 1 }
HrProcessorEntry ::= SEQUENCE {
hrProcessorFrwID ProductID,
hrProcessorLoad INTEGER
}
hrProcessorFrwID OBJECT-TYPE
Grillo & Waldbusser [Page 13]
RFC 1514 Host Resources MIB September 1993
SYNTAX ProductID
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The product ID of the firmware associated with the
processor."
::= { hrProcessorEntry 1 }
hrProcessorLoad OBJECT-TYPE
SYNTAX INTEGER (0..100)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The average, over the last minute, of the
percentage of time that this processor was not
idle."
::= { hrProcessorEntry 2 }
hrNetworkTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrNetworkEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of network devices
contained by the host.
Note that this table is potentially sparse: a
(conceptual) entry exists only if the correspondent
value of the hrDeviceType object is
`hrDeviceNetwork'."
::= { hrDevice 4 }
hrNetworkEntry OBJECT-TYPE
SYNTAX HrNetworkEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry for one network device
contained by the host. The hrDeviceIndex in the
index represents the entry in the hrDeviceTable
that corresponds to the hrNetworkEntry.
As an example of how objects in this table are
named, an instance of the hrNetworkIfIndex object
might be named hrNetworkIfIndex.3"
INDEX { hrDeviceIndex }
::= { hrNetworkTable 1 }
Grillo & Waldbusser [Page 14]
RFC 1514 Host Resources MIB September 1993
HrNetworkEntry ::= SEQUENCE {
hrNetworkIfIndex INTEGER
}
hrNetworkIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of ifIndex which corresponds to this
network device."
::= { hrNetworkEntry 1 }
hrPrinterTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrPrinterEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of printers local to the
host.
Note that this table is potentially sparse: a
(conceptual) entry exists only if the correspondent
value of the hrDeviceType object is
`hrDevicePrinter'."
::= { hrDevice 5 }
hrPrinterEntry OBJECT-TYPE
SYNTAX HrPrinterEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry for one printer local to the
host. The hrDeviceIndex in the index represents
the entry in the hrDeviceTable that corresponds to
the hrPrinterEntry.
As an example of how objects in this table are
named, an instance of the hrPrinterStatus object
might be named hrPrinterStatus.3"
INDEX { hrDeviceIndex }
::= { hrPrinterTable 1 }
HrPrinterEntry ::= SEQUENCE {
hrPrinterStatus INTEGER,
hrPrinterDetectedErrorState OCTET STRING
}
Grillo & Waldbusser [Page 15]
RFC 1514 Host Resources MIB September 1993
hrPrinterStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
unknown(2),
idle(3),
printing(4),
warmup(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current status of this printer device. When
in the idle(1), printing(2), or warmup(3) state,
the corresponding hrDeviceStatus should be
running(2) or warning(3). When in the unknown
state, the corresponding hrDeviceStatus should be
unknown(1)."
::= { hrPrinterEntry 1 }
hrPrinterDetectedErrorState OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object represents any error conditions
detected by the printer. The error conditions are
encoded as bits in an octet string, with the
following definitions:
Condition Bit # hrDeviceStatus
lowPaper 0 warning(3)
noPaper 1 down(5)
lowToner 2 warning(3)
noToner 3 down(5)
doorOpen 4 down(5)
jammed 5 down(5)
offline 6 down(5)
serviceRequested 7 warning(3)
If multiple conditions are currently detected and
the hrDeviceStatus would not otherwise be
unknown(1) or testing(4), the hrDeviceStatus shall
correspond to the worst state of those indicated,
where down(5) is worse than warning(3) which is
worse than running(2).
Bits are numbered starting with the most
Grillo & Waldbusser [Page 16]
RFC 1514 Host Resources MIB September 1993
significant bit of the first byte being bit 0, the
least significant bit of the first byte being bit
7, the most significant bit of the second byte
being bit 8, and so on. A one bit encodes that
the condition was detected, while a zero bit
encodes that the condition was not detected.
This object is useful for alerting an operator to
specific warning or error conditions that may
occur, especially those requiring human
intervention."
::= { hrPrinterEntry 2 }
hrDiskStorageTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrDiskStorageEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of long-term storage
devices contained by the host. In particular, disk
devices accessed remotely over a network are not
included here.
Note that this table is potentially sparse: a
(conceptual) entry exists only if the correspondent
value of the hrDeviceType object is
`hrDeviceDiskStorage'."
::= { hrDevice 6 }
hrDiskStorageEntry OBJECT-TYPE
SYNTAX HrDiskStorageEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry for one long-term storage
device contained by the host. The hrDeviceIndex in
the index represents the entry in the hrDeviceTable
that corresponds to the hrDiskStorageEntry. As an
example, an instance of the hrDiskStorageCapacity
object might be named hrDiskStorageCapacity.3"
INDEX { hrDeviceIndex }
::= { hrDiskStorageTable 1 }
HrDiskStorageEntry ::= SEQUENCE {
hrDiskStorageAccess INTEGER,
hrDiskStorageMedia INTEGER,
hrDiskStorageRemoveble Boolean,
hrDiskStorageCapacity KBytes
Grillo & Waldbusser [Page 17]
RFC 1514 Host Resources MIB September 1993
}
hrDiskStorageAccess OBJECT-TYPE
SYNTAX INTEGER {
readWrite(1),
readOnly(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An indication if this long-term storage device is
readable and writable or only readable. This
should reflect the media type, any write-protect
mechanism, and any device configuration that
affects the entire device."
::= { hrDiskStorageEntry 1 }
hrDiskStorageMedia OBJECT-TYPE
SYNTAX INTEGER {
other(1),
unknown(2),
hardDisk(3),
floppyDisk(4),
opticalDiskROM(5),
opticalDiskWORM(6), -- Write Once Read Many
opticalDiskRW(7),
ramDisk(8)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An indication of the type of media used in this
long-term storage device."
::= { hrDiskStorageEntry 2 }
hrDiskStorageRemoveble OBJECT-TYPE
SYNTAX Boolean
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Denotes whether or not the disk media may be
removed from the drive."
::= { hrDiskStorageEntry 3 }
hrDiskStorageCapacity OBJECT-TYPE
SYNTAX KBytes
ACCESS read-only
STATUS mandatory
Grillo & Waldbusser [Page 18]
RFC 1514 Host Resources MIB September 1993
DESCRIPTION
"The total size for this long-term storage device."
::= { hrDiskStorageEntry 4 }
hrPartitionTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrPartitionEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of partitions for long-term
storage devices contained by the host. In
particular, partitions accessed remotely over a
network are not included here."
::= { hrDevice 7 }
hrPartitionEntry OBJECT-TYPE
SYNTAX HrPartitionEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry for one partition. The
hrDeviceIndex in the index represents the entry in
the hrDeviceTable that corresponds to the
hrPartitionEntry.
As an example of how objects in this table are
named, an instance of the hrPartitionSize object
might be named hrPartitionSize.3.1"
INDEX { hrDeviceIndex, hrPartitionIndex }
::= { hrPartitionTable 1 }
HrPartitionEntry ::= SEQUENCE {
hrPartitionIndex INTEGER,
hrPartitionLabel InternationalDisplayString,
hrPartitionID OCTET STRING,
hrPartitionSize KBytes,
hrPartitionFSIndex INTEGER
}
hrPartitionIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for each partition on this long-
term storage device. The value for each long-term
storage device must remain constant at least from
one re-initialization of the agent to the next re-
Grillo & Waldbusser [Page 19]
RFC 1514 Host Resources MIB September 1993
initialization."
::= { hrPartitionEntry 1 }
hrPartitionLabel OBJECT-TYPE
SYNTAX InternationalDisplayString (SIZE (0..128))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A textual description of this partition."
::= { hrPartitionEntry 2 }
hrPartitionID OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A descriptor which uniquely represents this
partition to the responsible operating system. On
some systems, this might take on a binary
representation."
::= { hrPartitionEntry 3 }
hrPartitionSize OBJECT-TYPE
SYNTAX KBytes
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The size of this partition."
::= { hrPartitionEntry 4 }
hrPartitionFSIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The index of the file system mounted on this
partition. If no file system is mounted on this
partition, then this value shall be zero. Note
that multiple partitions may point to one file
system, denoting that that file system resides on
those partitions. Multiple file systems may not
reside on one partition."
::= { hrPartitionEntry 5 }
-- The File System Table
hrFSTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrFSEntry
Grillo & Waldbusser [Page 20]
RFC 1514 Host Resources MIB September 1993
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of file systems local to
this host or remotely mounted from a file server.
File systems that are in only one user's
environment on a multi-user system will not be
included in this table."
::= { hrDevice 8 }
hrFSEntry OBJECT-TYPE
SYNTAX HrFSEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry for one file system local to
this host or remotely mounted from a file server.
File systems that are in only one user's
environment on a multi-user system will not be
included in this table.
As an example of how objects in this table are
named, an instance of the hrFSMountPoint object
might be named hrFSMountPoint.3"
INDEX { hrFSIndex }
::= { hrFSTable 1 }
-- Registration for some popular File System types,
-- for use with hrFSType.
hrFSTypes OBJECT IDENTIFIER ::= { hrDevice 9 }
hrFSOther OBJECT IDENTIFIER ::= { hrFSTypes 1 }
hrFSUnknown OBJECT IDENTIFIER ::= { hrFSTypes 2 }
hrFSBerkeleyFFS OBJECT IDENTIFIER ::= { hrFSTypes 3 }
hrFSSys5FS OBJECT IDENTIFIER ::= { hrFSTypes 4 }
-- DOS
hrFSFat OBJECT IDENTIFIER ::= { hrFSTypes 5 }
-- OS/2 High Performance File System
hrFSHPFS OBJECT IDENTIFIER ::= { hrFSTypes 6 }
-- Macintosh Hierarchical File System
hrFSHFS OBJECT IDENTIFIER ::= { hrFSTypes 7 }
-- Macintosh File System
hrFSMFS OBJECT IDENTIFIER ::= { hrFSTypes 8 }
-- Windows NT
hrFSNTFS OBJECT IDENTIFIER ::= { hrFSTypes 9 }
Grillo & Waldbusser [Page 21]
RFC 1514 Host Resources MIB September 1993
hrFSVNode OBJECT IDENTIFIER ::= { hrFSTypes 10 }
hrFSJournaled OBJECT IDENTIFIER ::= { hrFSTypes 11 }
-- CD File systems
hrFSiso9660 OBJECT IDENTIFIER ::= { hrFSTypes 12 }
hrFSRockRidge OBJECT IDENTIFIER ::= { hrFSTypes 13 }
hrFSNFS OBJECT IDENTIFIER ::= { hrFSTypes 14 }
hrFSNetware OBJECT IDENTIFIER ::= { hrFSTypes 15 }
-- Andrew File System
hrFSAFS OBJECT IDENTIFIER ::= { hrFSTypes 16 }
-- OSF DCE Distributed File System
hrFSDFS OBJECT IDENTIFIER ::= { hrFSTypes 17 }
hrFSAppleshare OBJECT IDENTIFIER ::= { hrFSTypes 18 }
hrFSRFS OBJECT IDENTIFIER ::= { hrFSTypes 19 }
-- Data General
hrFSDGCFS OBJECT IDENTIFIER ::= { hrFSTypes 20 }
-- SVR4 Boot File System
hrFSBFS OBJECT IDENTIFIER ::= { hrFSTypes 21 }
HrFSEntry ::= SEQUENCE {
hrFSIndex INTEGER,
hrFSMountPoint InternationalDisplayString,
hrFSRemoteMountPoint InternationalDisplayString,
hrFSType OBJECT IDENTIFIER,
hrFSAccess INTEGER,
hrFSBootable Boolean,
hrFSStorageIndex INTEGER,
hrFSLastFullBackupDate DateAndTime,
hrFSLastPartialBackupDate DateAndTime
}
hrFSIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for each file system local to this
host. The value for each file system must remain
constant at least from one re-initialization of
the agent to the next re-initialization."
::= { hrFSEntry 1 }
hrFSMountPoint OBJECT-TYPE
SYNTAX InternationalDisplayString (SIZE(0..128))
ACCESS read-only
STATUS mandatory
Grillo & Waldbusser [Page 22]
RFC 1514 Host Resources MIB September 1993
DESCRIPTION
"The path name of the root of this file system."
::= { hrFSEntry 2 }
hrFSRemoteMountPoint OBJECT-TYPE
SYNTAX InternationalDisplayString (SIZE(0..128))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A description of the name and/or address of the
server that this file system is mounted from.
This may also include parameters such as the mount
point on the remote file system. If this is not a
remote file system, this string should have a
length of zero."
::= { hrFSEntry 3 }
hrFSType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of this object identifies the type of
this file system."
::= { hrFSEntry 4 }
hrFSAccess OBJECT-TYPE
SYNTAX INTEGER {
readWrite(1),
readOnly(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An indication if this file system is logically
configured by the operating system to be readable
and writable or only readable. This does not
represent any local access-control policy, except
one that is applied to the file system as a whole."
::= { hrFSEntry 5 }
hrFSBootable OBJECT-TYPE
SYNTAX Boolean
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A flag indicating whether this file system is
bootable."
Grillo & Waldbusser [Page 23]
RFC 1514 Host Resources MIB September 1993
::= { hrFSEntry 6 }
hrFSStorageIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The index of the hrStorageEntry that represents
information about this file system. If there is
no such information available, then this value
shall be zero. The relevant storage entry will be
useful in tracking the percent usage of this file
system and diagnosing errors that may occur when
it runs out of space."
::= { hrFSEntry 7 }
hrFSLastFullBackupDate OBJECT-TYPE
SYNTAX DateAndTime
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The last date at which this complete file system
was copied to another storage device for backup.
This information is useful for ensuring that
backups are being performed regularly.
If this information is not known, then this
variable shall have the value corresponding to
January 1, year 0000, 00:00:00.0, which is encoded
as (hex)'00 00 01 01 00 00 00 00'."
::= { hrFSEntry 8 }
hrFSLastPartialBackupDate OBJECT-TYPE
SYNTAX DateAndTime
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The last date at which a portion of this file
system was copied to another storage device for
backup. This information is useful for ensuring
that backups are being performed regularly.
If this information is not known, then this
variable shall have the value corresponding to
January 1, year 0000, 00:00:00.0, which is encoded
as (hex)'00 00 01 01 00 00 00 00'."
::= { hrFSEntry 9 }
Grillo & Waldbusser [Page 24]
RFC 1514 Host Resources MIB September 1993
-- The Host Resources Running Software Group
--
-- Implementation of this group is optional.
--
-- The hrSWRunTable contains an entry for each distinct piece of
-- software that is running or loaded into physical or virtual
-- memory in preparation for running. This includes the host's
-- operating system, device drivers, and applications.
hrSWOSIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of the hrSWRunIndex for the
hrSWRunEntry that represents the primary operating
system running on this host. This object is
useful for quickly and uniquely identifying that
primary operating system."
::= { hrSWRun 1 }
hrSWRunTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrSWRunEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of software running on the
host."
::= { hrSWRun 2 }
hrSWRunEntry OBJECT-TYPE
SYNTAX HrSWRunEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry for one piece of software
running on the host Note that because the installed
software table only contains information for
software stored locally on this host, not every
piece of running software will be found in the
installed software table. This is true of software
that was loaded and run from a non-local source,
such as a network-mounted file system.
As an example of how objects in this table are
named, an instance of the hrSWRunName object might
be named hrSWRunName.1287"
INDEX { hrSWRunIndex }
Grillo & Waldbusser [Page 25]
RFC 1514 Host Resources MIB September 1993
::= { hrSWRunTable 1 }
HrSWRunEntry ::= SEQUENCE {
hrSWRunIndex INTEGER,
hrSWRunName InternationalDisplayString,
hrSWRunID ProductID,
hrSWRunPath InternationalDisplayString,
hrSWRunParameters InternationalDisplayString,
hrSWRunType INTEGER,
hrSWRunStatus INTEGER
}
hrSWRunIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for each piece of software running
on the host. Wherever possible, this should be the
system's native, unique identification number."
::= { hrSWRunEntry 1 }
hrSWRunName OBJECT-TYPE
SYNTAX InternationalDisplayString (SIZE (0..64))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A textual description of this running piece of
software, including the manufacturer, revision,
and the name by which it is commonly known. If
this software was installed locally, this should be
the same string as used in the corresponding
hrSWInstalledName."
::= { hrSWRunEntry 2 }
hrSWRunID OBJECT-TYPE
SYNTAX ProductID
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The product ID of this running piece of software."
::= { hrSWRunEntry 3 }
hrSWRunPath OBJECT-TYPE
SYNTAX InternationalDisplayString (SIZE(0..128))
ACCESS read-only
STATUS mandatory
DESCRIPTION
Grillo & Waldbusser [Page 26]
RFC 1514 Host Resources MIB September 1993
"A description of the location on long-term storage
(e.g. a disk drive) from which this software was
loaded."
::= { hrSWRunEntry 4 }
hrSWRunParameters OBJECT-TYPE
SYNTAX InternationalDisplayString (SIZE(0..128))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A description of the parameters supplied to this
software when it was initially loaded."
::= { hrSWRunEntry 5 }
hrSWRunType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
operatingSystem(2),
deviceDriver(3),
application(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of this software."
::= { hrSWRunEntry 6 }
hrSWRunStatus OBJECT-TYPE
SYNTAX INTEGER {
running(1),
runnable(2), -- waiting for resource (CPU, memory, IO)
notRunnable(3), -- loaded but waiting for event
invalid(4) -- not loaded
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of this running piece of software.
Setting this value to invalid(4) shall cause this
software to stop running and to be unloaded."
::= { hrSWRunEntry 7 }
-- The Host Resources Running Software Performance Group
-- Implementation of this group is optional.
--
-- The hrSWRunPerfTable contains an entry corresponding to
-- each entry in the hrSWRunTable.
Grillo & Waldbusser [Page 27]
RFC 1514 Host Resources MIB September 1993
hrSWRunPerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrSWRunPerfEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of running software
performance metrics."
::= { hrSWRunPerf 1 }
hrSWRunPerfEntry OBJECT-TYPE
SYNTAX HrSWRunPerfEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry containing software
performance metrics. As an example, an instance
of the hrSWRunPerfCPU object might be named
hrSWRunPerfCPU.1287"
INDEX { hrSWRunIndex } -- This table augments information in
-- the hrSWRunTable.
::= { hrSWRunPerfTable 1 }
HrSWRunPerfEntry ::= SEQUENCE {
hrSWRunPerfCPU INTEGER,
hrSWRunPerfMem KBytes
}
hrSWRunPerfCPU OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of centi-seconds of the total system's
CPU resources consumed by this process. Note that
on a multi-processor system, this value may
increment by more than one centi-second in one
centi-second of real (wall clock) time."
::= { hrSWRunPerfEntry 1 }
hrSWRunPerfMem OBJECT-TYPE
SYNTAX KBytes
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total amount of real system memory allocated
to this process."
::= { hrSWRunPerfEntry 2 }
Grillo & Waldbusser [Page 28]
RFC 1514 Host Resources MIB September 1993
-- The Host Resources Installed Software Group
--
-- Implementation of this group is optional.
--
-- The hrSWInstalledTable contains an entry for each piece
-- of software installed in long-term storage (e.g. a disk
-- drive) locally on this host. Note that this does not
-- include software loadable remotely from a network
-- server.
--
-- This table is useful for identifying and inventorying
-- software on a host and for diagnosing incompatibility
-- and version mismatch problems between various pieces
-- of hardware and software.
hrSWInstalledLastChange OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of sysUpTime when an entry in the
hrSWInstalledTable was last added, renamed, or
deleted. Because this table is likely to contain
many entries, polling of this object allows a
management station to determine when re-downloading
of the table might be useful."
::= { hrSWInstalled 1 }
hrSWInstalledLastUpdateTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of sysUpTime when the hrSWInstalledTable
was last completely updated. Because caching of
this data will be a popular implementation
strategy, retrieval of this object allows a
management station to obtain a guarantee that no
data in this table is older than the indicated
time."
::= { hrSWInstalled 2 }
hrSWInstalledTable OBJECT-TYPE
SYNTAX SEQUENCE OF HrSWInstalledEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The (conceptual) table of software installed on
Grillo & Waldbusser [Page 29]
RFC 1514 Host Resources MIB September 1993
this host."
::= { hrSWInstalled 3 }
hrSWInstalledEntry OBJECT-TYPE
SYNTAX HrSWInstalledEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A (conceptual) entry for a piece of software
installed on this host.
As an example of how objects in this table are
named, an instance of the hrSWInstalledName object
might be named hrSWInstalledName.96"
INDEX { hrSWInstalledIndex }
::= { hrSWInstalledTable 1 }
HrSWInstalledEntry ::= SEQUENCE {
hrSWInstalledIndex INTEGER,
hrSWInstalledName InternationalDisplayString,
hrSWInstalledID ProductID,
hrSWInstalledType INTEGER,
hrSWInstalledDate DateAndTime
}
hrSWInstalledIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for each piece of software
installed on the host. This value shall be in the
range from 1 to the number of pieces of software
installed on the host."
::= { hrSWInstalledEntry 1 }
hrSWInstalledName OBJECT-TYPE
SYNTAX InternationalDisplayString (SIZE (0..64))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A textual description of this installed piece of
software, including the manufacturer, revision, the
name by which it is commonly known, and optionally,
its serial number."
::= { hrSWInstalledEntry 2 }
hrSWInstalledID OBJECT-TYPE
Grillo & Waldbusser [Page 30]
RFC 1514 Host Resources MIB September 1993
SYNTAX ProductID
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The product ID of this installed piece of
software."
::= { hrSWInstalledEntry 3 }
hrSWInstalledType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
operatingSystem(2),
deviceDriver(3),
application(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of this software."
::= { hrSWInstalledEntry 4 }
hrSWInstalledDate OBJECT-TYPE
SYNTAX DateAndTime
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The last-modification date of this application as
it would appear in a directory listing."
::= { hrSWInstalledEntry 5 }
END
5. References
[1] Rose M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based internets", STD 16, RFC
1155, Performance Systems International, Hughes LAN Systems, May
1990.
[2] Rose, M., and K. McCloghrie, Editors, "Concise MIB Definitions",
STD 16, RFC 1212, Performance Systems International, Hughes LAN
Systems, March 1991.
[3] McCloghrie K., and M. Rose, Editors, "Management Information
Base for Network Management of TCP/IP-based internets", STD 17,
RFC 1213, Performance Systems International, March 1991.
Grillo & Waldbusser [Page 31]
RFC 1514 Host Resources MIB September 1993
[4] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, SNMP Research,
Performance Systems International, Performance Systems
International, MIT Laboratory for Computer Science, May 1990.
[5] Information processing systems - Open Systems Interconnection -
Specification of Abstract Syntax Notation One (ASN.1),
International Organization for Standardization. International
Standard 8824, (December, 1987).
6. Acknowledgments
This document was produced by the Host Resources MIB working group.
In addition, the authors gratefully acknowledge the comments of the
following individuals:
Amatzia Ben-Artzi NetManage
Steve Bostock Novell
Stephen Bush GE Information Systems
Jeff Case SNMP Research
Chuck Davin Bellcore
Ray Edgarton Bell Atlantic
Mike Erlinger Aerospace Corporation
Tim Farley Magee Enterprises
Mark Kepke Hewlett-Packard
Bobby Krupczak Georgia Tech
Cheryl Krupczak Georgia Tech
Keith McCloghrie Hughes Lan Systems
Greg Minshall Novell
Dave Perkins Synoptics
Ed Reeder Objective Systems Integrators
Mike Ritter Apple Computer
Marshall Rose Dover Beach Consulting
Jon Saperia DEC
Rodney Thayer Sable Technology
Kaj Tesink Bellcore
Dean Throop Data General
7. Security Considerations
Security issues are not discussed in this memo.
Grillo & Waldbusser [Page 32]
RFC 1514 Host Resources MIB September 1993
8. Authors' Addresses
Pete Grillo
10915 NW Lost Park Drive
Portland OR 97229
Phone: +1 503 526 9766
EMail: pl0143@mail.psi.net
Steven Waldbusser
Carnegie Mellon University
4910 Forbes Ave.
Pittsburgh, PA 15213
Phone: +1 412 268 6628
Fax: +1 412 268 4987
EMail: waldbusser@cmu.edu
Grillo & Waldbusser [Page 33]