💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc6479.txt captured on 2023-04-26 at 14:32:35.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Independent Submission X. Zhang
Request for Comments: 6479 T. Tsou
Category: Informational Futurewei Technologies
ISSN: 2070-1721 January 2012
IPsec Anti-Replay Algorithm without Bit Shifting
Abstract
This document presents an alternate method to do the anti-replay
checks and updates for IP Authentication Header (AH) and
Encapsulating Security Protocol (ESP). The method defined in this
document obviates the need for bit shifting and it reduces the number
of times an anti-replay window is adjusted.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This is a contribution to the RFC Series, independently of any other
RFC stream. The RFC Editor has chosen to publish this document at
its discretion and makes no statement about its value for
implementation or deployment. Documents approved for publication by
the RFC Editor are not a candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc6479.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document.
Zhang & Tsou Informational [Page 1]
RFC 6479 IPsec Anti-Replay Algorithm January 2012
Table of Contents
1. Introduction ....................................................2
2. Description of New Anti-Replay Algorithm ........................3
3. Example of New Anti-Replay Algorithm ............................5
4. Security Considerations .........................................9
5. Normative References ............................................9
6. Acknowledgements ................................................9
1. Introduction
"IP Authentication Header" [RFC4302] and "IP Encapsulating Security
Payload (ESP)" [RFC4303] define an anti-replay service that employs a
sliding window mechanism. The mechanism, when enabled by a receiver,
uses an anti-replay window of size W. This window limits how far out
of order a packet can be, relative to the packet with the highest
sequence number that has been authenticated so far. The window can
be represented by a range [WB, WT], where WB=WT-W+1. The whole
anti-replay window can be thought of as a string of bits. The value
of each bit indicates whether or not a packet with that sequence
number has been received and authenticated, so that the replay packet
can be detected and rejected. If the packet is received, the
receiver gets the sequence number S in the packet. If S is inside
window (S<=WT and S>=WB), then the receiver checks the corresponding
bit (location is S-WB) in the window to see if this S has already
been seen. If S<WB, the packet is dropped. If S>WT and is
validated, the window is advanced by (S-WT) bits. The new window
becomes [WB+S-WT, S]. The new bits in this new window are set to
indicate that no packets with those sequence numbers have been
received. The typical implementation (for example, the integrity
algorithm [RFC4302]) is done by shifting (S-WT) bits. In normal
cases, the packets arrive in order, which results in continuous
updates and bit-shifting operations.
[RFC4302] and [RFC4303] define minimum window sizes of 32 and 64.
But no requirement is established for minimum or recommended window
sizes beyond 64 packets. The window size needs to be based on
reasonable expectations for packet re-ordering. For a high-end,
multi-core network processor with multiple crypto cores, a window
size bigger than 64 or 128 is needed due to the varied IPsec
processing latency caused by different cores. In such a case, the
window sliding is tremendously costly even with hardware acceleration
to do the bit shifting. This document describes an alternate method
to avoid bit shifting. It only discusses the anti-replay processing
at the receiving side. The processing is always safe and has no
interoperability effects. Even with a window size bigger than the
usual 32- or 64-bit window, no interoperability issues are caused.
Zhang & Tsou Informational [Page 2]
RFC 6479 IPsec Anti-Replay Algorithm January 2012
Any node employing practices that potentially cause reordering beyond
the usual 32- or 64-bit window may lead to interoperability or
performance problems, however. For instance, if either the sending
node or routers along the path cause significant re-ordering, this
can lead to inability of the receiving IPsec endpoint to process the
packets, as many current implementations do not support the
extensions defined in this memo. Similarly, such reordering can
cause significant problems for transport and upper-layer protocols,
and is generally best avoided.
2. Description of the New Anti-Replay Algorithm
Here we present an easy way to update the window index only, while
also reducing the number window updates. The basic idea is
illustrated in the following figures. Suppose that we configure the
window size W, which consists of M-1 blocks, where M is a power of
two (2). Each block contains N bits, where N is also a power of two
(2). It can be a byte (8 bit) or word (32 bit), or multiple words.
The supported sliding window size is (M-1)*N. However, it covers up
M blocks (four blocks as shown in Figure 1). All these M blocks are
circulated and become a ring of blocks, each with N bits. In this
way, the supported sliding window (M-1 blocks) is always a subset
window of the actual window when the window slides.
Initially, the actual window is defined by a low- and high-end index
[WB, WT], as illustrated in Figure 1.
+--------+--------+--------+--------+
|xxxxxxcc|cccccccc|cccccccc|ccccc100|
+--------+--------+--------+--------+
^ ^
| |
WB WT
Figure 1: The sliding window [WB, WT] in which WT is the last
validated sequence number, and the supported window size W is
WT-WB+1. (x=don't care bit, c=check bit)
Zhang & Tsou Informational [Page 3]
RFC 6479 IPsec Anti-Replay Algorithm January 2012
If we receive a packet with the sequence number (S) greater than WT,
we slide the window. But we only change the window index by adding
the difference (S-WT) to both WT and WB (WB is automatically changed
as the window size is fixed). So, S becomes the largest sequence
number of the received packets. Figure 2 shows the case that the
packet with sequence number S=WT+1 is received.
+--------+--------+--------+--------+
|xxxxxxcc|cccccccc|cccccccc|ccccc110|
+--------+--------+--------+--------+
^ ^
| |
WB WT
Figure 2: The sliding window [WB, WT] after S=WT+1
If S is in a different block from where WT is, we have to initialize
all bit values in the blocks to 0 without bit shifting. If S passes
several blocks, we have to initialize several blocks instead of only
one block. Figure 3 shows that the sequence number already passed
the block boundary. Immediately after the update, all the check bits
should be 0 in the block where WT resides.
+--------+--------+--------+--------+
|ccc10000|xxxxcccc|cccccccc|cccccccc|
+--------+--------+--------+--------+
^ ^
| |
WT WB
Figure 3: The sliding window [WB, WT] after S passes the boundary
After the update, the new window still covers the configured window.
This means the configured sub-window also slides, conforming to the
sliding window protocol. The actual effect is somewhat like
shifting the block. In this way, the bit shifting is deemed
unnecessary.
It is also easier and much faster to check the window with the
sequence number because the sequence number check does not
depend on the lowest index WB. Instead, it only depends on the
sequence number of the received packet. If we receive a sequence
number S, the bit location is the lowest several bits of the
sequence number, which only depends on the block size (N). The
block index is several bits before the location bits, which only
depends on the window size (M).
Zhang & Tsou Informational [Page 4]
RFC 6479 IPsec Anti-Replay Algorithm January 2012
We do not specify how many redundancy bits are needed, except that
it should be a power of two (2) for computation efficiency. If the
microprocessor is 32 bits, 32 might be a better choice while 64
might be better for 64-bit microprocessor. For a microprocessor
with cache support, one cache line is also a good choice. It also
depends on the size of the sliding window. If we have N
redundancy bits (for example, 32 bits in the above description),
we only need 1/N times update of blocks, comparing to the
bit-shifting algorithm in [RFC4302].
The cost of this method is extra byte(s) being used as a redundant
window. The cost will be minimal if the window size is big enough.
Actually, the extra redundant bits are not completely wasted. We
could reuse the unused bits in the block where index WB resides,
i.e., the supported window size could be (M-1)*N, plus the unused
bits in the last block.
3. Example of the New Anti-Replay Algorithm
Here is the example code to implement the algorithm of anti-replay
checks and updates, which is described in the previous sections.
<CODE BEGINS>
/**
* Copyright (c) 2012 IETF Trust and the persons identified as
* authors of the code. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, is permitted pursuant to, and subject to the license
* terms contained in, the Simplified BSD License set forth in Section
* 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents
* (http://trustee.ietf.org/license-info).
*
*/
/**
* In this algorithm, the hidden window size must be a power of two,
* for example, 1024 bits. The redundant bits must also be a power of
* two, for example 32 bits. Thus, the supported anti-replay window
* size is the hidden window size minus the redundant bits. It is 992
* in this example. The size of the integer depends on microprocessor
* architecture. In this example, we assume that the software runs on
* a 32-bit microprocessor. So the size of the integer is 32. In order
* to convert the bitmap into an array of integers, the total number of
* integers is the hidden window size divided by the size of the
* integer.
*
Zhang & Tsou Informational [Page 5]
RFC 6479 IPsec Anti-Replay Algorithm January 2012
* struct ipsec_sa contains the window and window related parameters,
* such as the window size and the last acknowledged sequence number.
*
* all the value of macro can be changed, but must follow the rule
* defined in the algorithm.
*/
#define SIZE_OF_INTEGER 32 /** 32-bit microprocessor */
#define BITMAP_LEN (1024/ SIZE_OF_INTEGER)
/** in terms of the 32-bit integer */
#define BITMAP_INDEX_MASK (IPSEC_BITMAP_LEN-1)
#define REDUNDANT_BIT_SHIFTS 5
#define REDUNDANT_BITS (1<<REDUNDANT_BIT_SHIFTS)
#define BITMAP_LOC_MASK (IPSEC_REDUNDANT_BITS-1)
int
ipsec_check_replay_window (struct ipsec_sa *ipsa,
uint32_t sequence_number)
{
int bit_location;
int index;
/**
* replay shut off
*/
if (ipsa->replaywin_size == 0) {
return 1;
}
/**
* first == 0 or wrapped
*/
if (sequence_number == 0) {
return 0;
}
/**
* first check if the sequence number is in the range
*/
if (sequence_number>ipsa->replaywin_lastseq) {
return 1; /** larger is always good */
}
Zhang & Tsou Informational [Page 6]
RFC 6479 IPsec Anti-Replay Algorithm January 2012
/**
* The packet is too old and out of the window
*/
if ((sequence_number + ipsa->replaywin_size) <
ipsa->replaywin_lastseq) {
return 0;
}
/**
* The sequence is inside the sliding window
* now check the bit in the bitmap
* bit location only depends on the sequence number
*/
bit_location = sequence_number&BITMAP_LOC_MASK;
index = (sequence_number>>REDUNDANT_BIT_SHIFTS)&BITMAP_INDEX_MASK;
/*
* this packet has already been received
*/
if (ipsa->replaywin_bitmap[index]&(1<<bit_location)) {
return 0;
}
return 1;
}
int
ipsec_update_replay_window (struct ipsec_sa *ipsa,
uint32_t sequence_number)
{
int bit_location;
int index, index_cur, id;
int diff;
if (ipsa->replaywin_size == 0) { /** replay shut off */
return 1;
}
if (sequence_number == 0) {
return 0; /** first == 0 or wrapped */
}
Zhang & Tsou Informational [Page 7]
RFC 6479 IPsec Anti-Replay Algorithm January 2012
/**
* the packet is too old, no need to update
*/
if ((ipsa->replaywin_size + sequence_number) <
ipsa->replaywin_lastseq) {
return 0;
}
/**
* now update the bit
*/
index = (sequence_number>>REDUNDANT_BIT_SHIFTS);
/**
* first check if the sequence number is in the range
*/
if (sequence_number>ipsa->replaywin_lastseq) {
index_cur = ipsa->replaywin_lastseq>>REDUNDANT_BIT_SHIFTS;
diff = index - index_cur;
if (diff > BITMAP_LEN) { /* something unusual in this case */
diff = BITMAP_LEN;
}
for (id = 0; id < diff; ++id) {
ipsa->replaywin_bitmap[(id+index_cur+1)&BITMAP_INDEX_MASK]
= 0;
}
ipsa->replaywin_lastseq = sequence_number;
}
index &= BITMAP_INDEX_MASK;
bit_location = sequence_number&BITMAP_LOC_MASK;
/* this packet has already been received */
if (ipsa->replaywin_bitmap[index]&(1<<bit_location)) {
return 0;
}
ipsa->replaywin_bitmap[index] |= (1<<bit_location);
return 1;
}
<CODE ENDS>
Zhang & Tsou Informational [Page 8]
RFC 6479 IPsec Anti-Replay Algorithm January 2012
4. Security Considerations
This document does not change [RFC4302] or [RFC4303]. It provides
an alternate method for anti-replay.
5. Acknowledgements
The idea in this document came from the software design on one
high-performance multi-core network processor. The new network
processor core integrates a dozen of crypto core in a distributed
way, which makes hardware anti-replay service impossible.
6. Normative References
[RFC4302] Kent, S., "IP Authentication Header", RFC 4302, December
2005.
[RFC4303] Kent, S., "IP Encapsulating Security Payload (ESP)", RFC
4303, December 2005.
Authors' Addresses
Xiangyang Zhang
Futurewei Technologies
2330 Central Expressway
Santa Clara, California 95051
USA
Phone: +1-408-330-4545
EMail: xiangyang.zhang@huawei.com
Tina Tsou (Ting Zou)
Futurewei Technologies
2330 Central Expressway
Santa Clara, California 95051
USA
Phone: +1-408-859-4996
EMail: tena@huawei.com
Zhang & Tsou Informational [Page 9]