gemini - kennedy.gemi.dev

💾 Archived View for gemini.spam.works › mirrors › textfiles › phreak › BOXES › diverter captured on 2022-07-17 at 10:38:47.
-=-=-=-=-=-=-

      HOW TO BUILD AND USE A DIVERTER BOX.

      Designed and Written by Lord Zartan




PARTS LIST:
           2 SPDT Miniature PC RELAY (about 9v, 500 ohm)
           2 SPDT Miniature PC RELAY (about 5v,250 - 500 ohm)
             SPDT Miniature Switch
             2200 or so MFD electrolytic capacitor
             4 meg Pot resistor
             .01 uF capacitor
             555 timer chip
           2 diodes (1N914)
             10 K resistor
           2 4.7K resistor
             9 volt battery -w- clip
             Pc Board
             4 alligator clips
             some kind of a box (small)
             some 22 or 30 gauge wire to work with.

If you don't know how to put together a project by looking at a
schematic, then isn't the project to start with.  I would ask someone
with some electronics knowledge to give you a helping hand.  This
has to be put together on a pc-board.  Enough talk, now the schematic:
                                                             ????
NOTE * Print in Compressed Mode or Display in 25 x 50    ?????????
                                                         ?   ?C ??
                                                         ?  ??o ?5V
                                                         ?  ??i ?
                           +9V                           ?   ?l ??
                                                         ? ???????
                            ^                            ? ? ????
                 ????????????????????????????            ? ?NC??o????????
                 ?  ?       ?   ?           ?            ? ?            ?
               ???  ?       ?   ?           ?            ? ?   ?o?????  ?
               ? /  ?       8   4           ?            ? ?  -      ?  ?
         4000K?? \  ?   ?????????????       ?            ? ?  ??o    ?  ?
               ?>/  ?   ?           ?       ?    1N914   ? ? ????    ?  ?
    ???? (4 MEG) \  ?   ???? ??? ????3?????????????>??????????????   ?  ?
?????C???  Pot   ?  ?   ??   ?   ?  ?       ?          1?  ? ?C ??   ?  ?
?   ?o ??  ??????????   ???? ??? ????       /          N?  ???o ?    ?  ?
?  ??i ?9V ?     ??????7?  ?   ?   ??   10K?\          9^  ???i ?5V  ?  ?<R 2
?  ??l ??  ?     ?      ???? ??? ????       /          1?  ? ?l ??   ?
? ???????  ?     ?      ?           ?       \          4??????????   ?
? ? ????   ?     ??????6? Timer I C ?2??????????????    ?    ????    ?
? ?        ?     ?      ?           ?              ?    ?  NC??o????????<T 2
? ? ??o?????     ?      ?????????????   ?????o NC  ?    ?            ?
? ?              ?        1    5        ??         ?    ?     ?o???? ?
? ?  ?o??        ?        ?    ?          ?        ?    ?    -     ? ?
? ? ?   ?        ?        ?    ?           ??o???  ?    ?    ??o   ? ?
? ? ??o ?        ?        ?    ?                ?  ?    ?          ? ?
? ?     ?        ?        ?    ?                ?  ?    ???????????? ?
? ?     ?       ???       ?   ???       ?????o??????    ??           ?
? ?     ? 2000?F_^_       ?   _^_.01?F          ?       ?? ???????????
? ?     ?        ?        ?    ?                ?       ?? ?
? ?     ??????????        ?    ?         ????   ?       ?? ?
? /              ?        ?    ?     ?????C???  ?       ?? ?
? \              ?        ?    ?     ?   ?o ??  ?       ?? ?
? /4.7K?         ?        ?    ?     ?  ??i ?9V ?       ?? ?
? \              ?        ?    ?     ?  ??l ??  ?       ?? ?
? ?              ?        ?    ?     ?  ??????  ?       ?? ?
? ?              ?        ?    ?     ?  ?????   ?       ?? ?
? ?              ????????????????????????????????????????? ?
? ?   ??  ?               ?          ?  ?                ? ?
? ?   ? ? ?             ?????        ?  ?????????????????? ?
? ?   o o o              ???         ?        ?            ?
? ?     ? ?               ?          ??/\/\?????????????????
? ?     ? ?                            4.7K?  ?  ?
? ??????? ??<R 3                              ?  ????????<R 1
?                                             ?
?                                             ?
????????????<T 3                              ???????????<T 1


    KEY
-----------

R 1 , T 1  Line one, diverts to line 2

R 2 , T 2  Lind Actualy Dialing out on

R 3 , R 3  A.D.D. (Optional Asshole Disconnect Director)*See note


/\/\

\     Sign for a Resistor
/
\
/




___
_^_   Sign for Capacitor





>I

___   Sign for Diode
 ^
 I




---o

 --o  Sign For SPDT or SPDT for Relay
-
---o


	Note: Add; well lets say some asshole you gave the diverter number to is

       Allways on it, just make sure you don't give the third line. The
       ADD line as its called when called with disconect and reset The
       555 so you can call and use the diverter.

   OPERATION
---------------


When line 1# is called it triggers the 555 to charge the 5v relay's.
For the time specified by the 2200MFD & the 4 meg resistor. Then poof
both lines are now connected and you dial out. Now the A.D.D. works by
Reducing the resistence thus triggering the 555 to resest when someone
calls Line #3.

Whew!  Well, the schematic explains almost everything.  It would be
helpful to you if you used one color for the line #1 clips and another
for the line #2 clips and line #3. It will work even if you get the ring &
tip mixed up, but you must get all of the clips on the right line.  But,
to be safe, you could put tags on each clip labeling it RING #1, RING #2,
RING #3.




   USE
---------

Installation.  Find one of those green posts that are about 3 feet high.
They are everywhere.  Get a socket wrench to open it up.  There will
be (a) row(s) of paired up posts.  Each pair of posts represents a line.
YOU *MUST* KNOW THE NUMBER OF LINE #1.  Sometimes the number is tagged
on to the pair of wires leading up to the posts, if so pick these posts
as your line #1.  Then you can pick any other set of posts for line #2.

Now to the good part.  Use of the the final product.  When you call up
line one from your house you will get a dial tone almost immediately.
Using DTMF you can dial anywhere that the person who owns line #2 has
service to.  Which means you can direct dial alliance, Australia, and
your favorite BBS for FREE.

The Telco. will undoubtably discover the device after 2 days, so post
the number on your favorite boards so you can abuse it while it is in
service.  With a 2200 uF capacitor and a 1 meg resistor you will
get a 50 minute call before it disconnects you.  By lowering the value
of the resistor and capacitor you can change the time to your taste.
So don't dial a wrong number, because you will have to wait 50 minutes
until it resets again or use the ADD to reset the box.
Here is the formula for time:

2*R1    C1              C1 is in microfarads
---- * ----             R1 is in Kohms
100     10              See schematic for location of R1 and C1.
-----------  = Minutes
    60

The time produced by this formula is only approximate.

Well, that is one of the more complicated boxes to build.  But it
is very useful and will pay for itself with its first use.   It
would be wise to remove it before the Telco. finds it so you won't
have to make another, or install it on a line that belongs to a
family that is on vacation (GOOD IDEA)

                           Written By Lord Zartan of NPA