💾 Archived View for gemini.spam.works › mirrors › textfiles › groups › SHAWN › nuclear.txt captured on 2023-01-29 at 15:08:14.
View Raw
More Information
⬅️ Previous capture (2022-06-12)
-=-=-=-=-=-=-
???????????????????????????????????????????????????????????????????????????
??23 Oct 90????????????????????_ROR_-_ALUCARD_?????????????????????????? ??
? ? A ??
? ? ???
? SIR DEATH'S LABORATORY A ??????
? Tfile ??
? How to Build a Nuclear Reactor Distribution ??
????? Centere ??
?? ? - RoR - ??
? A ?_____________________________________________________________________??
? ?? Shawn-Da-Lay Boy Productions, Inc.????????????????????????????????????
????????????????????????????????????????????????????????????????????????????
???The HQ of SDBP, Inc - 510/237/8563??PolySpock Project - 510/524/3649???
?Drop Sites?????? Hollow's Renaissance - 510/669/9432?????Drop Sites??????
SIR DEATH'S LABORATORY
HOW TO BUILD A NUCLEAR REACTOR:
A back-yard reactor is easy to build, and a fascinating
educational project. It can also produce an inexpensive
supply of hot water - handy in these days of high fuel bills!
Just follow theses step by step instructions.
You will need:
- A 32 gallon plastic trash can (heavy duty, and preferably
with locking handles to discourage inquisitive pets and
children).
- 45 Feet of 3" PVC plumbing pipe
- 10 Feet of 2 1/2" PVC plumping pipe
- 12 Standard 75mm rods of U 235
1. Cut your three-inch piping into 28" lengths-nineteen in
all. Position the sections vertically in the trash. A
few inches of sand in the bottom will help hold them if
necessary.
2. With the keyhole saw, cut seven holes in the trash can
lid, corresponding to the locations of the pipes. These
are for inserting your control rods. Cut three more
smaller holes as shown.
3. Now for the control rods. Cut the smaller pipe into 34"
lengths - seven in all. Seal one end securely with duct
tape. Fill each rod to the top with an appropriate
damping material. The "pros" use graphite, but a good
potting soil will work nicely.
4. Slide the fuel rods into the correct pipes. Safety
first! Wear gardening gloves when handling the U 235.
5. Pop on the lid, lining up the holes with the control rod
sleeves. Insert a garden hose in one of the 5/8" holes,
and fill the trash can right to the top. Heavy water is
best here. (If you live near a nuclear power plant, you
may already be getting heavy water from your tap. If
not, plain water will do).
A second garden hose will carry the heated water out,
provided the can is higher than the end of the hose.
NOTE: Before doing steps 4 & 5, be sure to insert the
control rods into their sleeves. Otherwise, there is the
risk of a "runaway" reaction. The inserted rods will
stick up six inches above the lid, so you can grasp them
for removal.
6. Push the meat thermometer into the small hole in the lid.
Now, by altering the flow of water from the faucet, and
by removing more or fewer control rods, you should be
able to maintain a constant temperature inside the
reactor.
You can use the hot water you produce to run a toy
turbine, heat your doghouse, or fill a ht tub. Any overflow
can irrigate your garden, where it will often produce
beautiful and unusual foliage. Always dispose of spent fuel
rods properly.
- U 235 rods can often be obtained through local hobby or
terrorist groups. Or order by mail from "The Electric Pub,
1113 E. 7th St. Stagfarm, NJ 08865. You must state that
-30-
nk of dying in this way.
We've hope you enjoyed this.
Written a@ ust state that
-30-