💾 Archived View for gemini.spam.works › mirrors › textfiles › uploads › prox.txt captured on 2023-01-29 at 12:59:07.
⬅️ Previous capture (2020-10-31)
-=-=-=-=-=-=-
Making Impovised Proximity Mines
By:MassExodus
All of these Files are for informational purposes only and any trouble
That may result from reading this file is your sole responsiblity and the
author or his ISP may be held liable for any legal trouble that may insue.
Devices such as this can cause serious harm.
Have you ever played any of the James Bond series games or perhaps
Watched one of the films and wondered how cool it would be to have some of
his
little Toys? While if you have this atricle is for you because today i will
be
teaching you how to make an Proximity Mine.
What you'll need is this.:
1 Motion Sensor\alarm Easily found at any local Radio Shack. now this will
run you about
$9.99 But don't Cheap out.(you'll be unpleasently suprised if it blows up in
your face because
of Shaudy Workmanship,)
Some Gunpowder-The Amount Varies with how big you want the Effect to
be.(Taken from Shells
Or perhaps Fireworks. if you don't have access to Plain)
1 Glass Test tube(regual size)-if you can find a glass test tube this can be
substituted
With any container Able to hold the amount of gun powder you need. i just
like the glass
because its pretty.
A length or wire or Several alligator Clips.
1 Igniter.(these Can be found in hobby shops that Sell Rocketry Supplies,
Now make sure you
Only buy the one time ignitors The Kind that are like to little metal pins
and a strip of
paper. and not the mechanical type)
Now that you have the supplys Lets move onto the Fun part.
---:::-Construction
First Thing you should do is play with the motion sensor to make sure it
works right
and to figure out how it works.
You need to Open the Case without damaging ANYTHING!!! and find where the
Speaker
That the Alarm uses when it Goes Off. If your not sure which peice is the
Speaker you
Shouldnt be doing this...
Now That you've Found The Speaker. Look at it and the Wires that connect it
to the Device.
There will be two wires now Take Something and make a good cut at the end of
the wires about
1\4 of an inch to where they connect to the speaker.Now that you've
Disconnected the Speaker
Take this wire and Strip a bit From the ends so you have about 1\4 inch bare
wire at the end.
Find a way to Get Some of the wire on the outside of the Case.(drill or Cut
a hole if you have to.)
The case Doesnt really matter anyway. Now Reclose the Case.
Now if You have the iq of a houseplant and have done this correctly it shoud
look like this.
I I <-Wires
I I
----------- <-Case
Take Some Alligator Clips and Clip them to Each of the little metal Prongs
on the bottom of
The ignitor(one Clip for Each Duh.!) and Clip the last two Clips onto the
two exposed wires
on the Outside of the Case.
It should look like this: --------------
[ ignitor ]
--------------
I I
hhHHH HHHhh
I I
I I
I I
hhHHH HHHhh
I I
I I
-------------- <--Case
Thats your Proximity Detonator.
Now it will probubly be a good idea to check the functionality of your
device by using
only a ignitor and No explosive(Just to be Sure).
Now just Put the Ignitor into you Container(with the Explosive) and Close
the lid\cap\whatever, just make
sure that the wires don't get severed!, and you have made your very own
proximity mine.
When your ready to use Just attach the Device to you container. and arm it
like you would if
it were still an alarm.
How it works.
Well Supposing you didn't get the kind of alarm that beeps before its
active. Once the
Motion Detector is set off. The electircal Charge Which would normaly make
the Alarm Sound
Is sent to The ignitor and that Sets off The Boom. Don't Get Hurt.
-----MassExodus------]-{