💾 Archived View for colincogle.name › blog › unifi-cloud-key-rescue › UCK-G2-PLUS%20boot%20messages%… captured on 2023-01-29 at 02:45:43.
-=-=-=-=-=-=-
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3-00214
S - IMAGE_VARIANT_STRING=JAASANAZA
S - OEM_IMAGE_VERSION_STRING=v0.2.8-ubnt.499f3c1.180713.2321
S - Boot Config, 0x000000e1
B - 269 - PBL, Start
B - 3144 - bootable_media_detect_entry, Start
B - 164402 - bootable_media_detect_success, Start
B - 164408 - elf_loader_entry, Start
B - 166057 - auth_hash_seg_entry, Start
B - 166339 - auth_hash_seg_exit, Start
B - 195201 - elf_segs_hash_verify_entry, Start
B - 321759 - PBL, End
B - 268339 - SBL1, Start
B - 313936 - pm_device_init, Start
B - 316437 - BOOT_DUMP: PMi8950_PON_FSM =0x20895 :DATA=0x9
B - 318572 - PON REASON:PM0:0x20 PM1:0x20
D - 29280 - pm_device_init, Delta
B - 343277 - usb: hs_phy_nondrive_start
B - 344467 - usb: hs_phy_nondrive_finish
B - 348096 - boot_flash_init, Start
D - 0 - boot_flash_init, Delta
B - 354989 - boot_config_data_table_init, Start
D - 5154 - boot_config_data_table_init, Delta - (976 Bytes)
B - 365146 - CDT version:3,Platform ID:250,Major ID:0,Minor ID:0,Subtype:0
B - 372344 - sbl1_ddr_set_params, Start
B - 376583 - cpr_init, Start
D - 1098 - cpr_init, Delta
B - 381585 - Pre_DDR_clock_init, Start
D - 244 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 394578 - do ddr sanity test, Start
D - 335 - do ddr sanity test, Delta
B - 400373 - pm_driver_init, Start
B - 407083 - Manually set to USB500 mode
B - 407571 - raw vbat: 3978, gain: -19
B - 411384 - vbat: 3789
B - 413732 - Battery good, bootup
D - 13389 - pm_driver_init, Delta
B - 424072 - DDR Training restore, Start
B - 426207 - DDR Training restore, End
B - 436058 - clock_init, Start
D - 183 - clock_init, Delta
B - 436302 - ubnt_preinit, Start
D - 0 - ubnt_preinit, Delta
B - 442250 - Image Load, Start
D - 84180 - QSEE Image Loaded, Delta - (1515964 Bytes)
B - 526460 - Image Load, Start
D - 366 - SEC Image Loaded, Delta - (2048 Bytes)
B - 533750 - sbl1_efs_handle_cookies, Start
D - 610 - sbl1_efs_handle_cookies, Delta
B - 541527 - ubnt, Start
B - 556747 - ubnt: ck-plus
B - 557662 - lp5562_load_engine: value: 0xad, rc=1
B - 566110 - POE: 1, QC: 0, PLUG: 0, Reset: 0, Rack: 1
B - 566171 - ubnt: reset button is pressed: 5
B - 1568584 - POE: 1, QC: 0, PLUG: 0, Reset: 0, Rack: 1
B - 1568615 - ubnt: reset button is pressed: 4
B - 2571028 - POE: 1, QC: 0, PLUG: 0, Reset: 0, Rack: 1
B - 2571058 - ubnt: reset button is pressed: 3
B - 3573471 - POE: 1, QC: 0, PLUG: 0, Reset: 0, Rack: 1
B - 3573502 - ubnt: reset button is pressed: 2
B - 4575915 - POE: 1, QC: 0, PLUG: 0, Reset: 0, Rack: 1
B - 4575945 - ubnt: reset button is pressed: 1
B - 5578358 - ubnt: marking for recovery
D - 5034421 - ubnt, Delta
B - 5578389 - Image Load, Start
D - 11102 - DEVCFG Image Loaded, Delta - (32380 Bytes)
B - 5589857 - Image Load, Start
D - 19215 - RPM Image Loaded, Delta - (168980 Bytes)
B - 5609102 - Image Load, Start
D - 43676 - APPSBL Image Loaded, Delta - (397644 Bytes)
B - 5652809 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 5658482 - USB D+ check, Start
B - 5663636 - usb:: dcp
D - 2165 - USB D+ check, Delta
B - 5667266 - SBL1, End
D - 5401214 - SBL1, Delta
S - Flash Throughput, 30000 KB/s (2121088 Bytes, 70322 us)
S - DDR Frequency, 931 MHz
S - Core 0 Frequency, 800 MHz
[0] lk - uart_dm initialized!
[0] welcome to lk
[10] platform_init()
[10] target_init()
[30] SDHC Running in HS400 mode
[40] Done initialization of the card
[40] pm8x41_get_is_cold_boot: cold boot
[40] Waiting for the RPM to populate smd channel table
[50] pm8x41_get_is_cold_boot: cold boot
[50] Unable to locate /bootselect partition
[60] Loading (recovery) image (10240000): start
[90] Loading (recovery) image (10240000): done
[90] use_signed_kernel=1, is_unlocked=1, is_tampered=0.
[100] decompressing kernel image: start
[340] decompressing kernel image: done
[400] Best match DTB tags 304/000000fa/0x00000000/0/10016/20011/0/0/a058354b/30ef1
[410] Using pmic info 0x10016/0x20011/0x0/0x0 for device 0x10016/0x20011/0x0/0x0
[420] cmdline: console=ttyHSL0,115200n8 quiet gpt
[420] Updating device tree: start
[560] Updating device tree: done
[560] Channel alloc freed
[570] booting linux @ 0x40080000, ramdisk @ 0x43600000 (5100406), tags/device tree @ 0x43400000
[570] Jumping to kernel via monitor
[ 0.132177] scm_call failed: func id 0x42000101, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 0.315101] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.315125] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.317252] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.317275] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.317296] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.317315] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.346637] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,dfs-sid-c0
[ 0.346664] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,link-sid-c0
[ 0.346689] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,lmh-sid-c0
[ 0.346777] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,dfs-sid-c1
[ 0.346801] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,link-sid-c1
[ 0.346824] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,lmh-sid-c1
[ 0.758549] scm_call failed: func id 0x42000c16, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 0.765621] msm_sharedmem: setup_shared_ram_perms: hyp_assign_phys failed IPA=0x0160x00000000fe500000 size=1572864 err=-5
[ 0.976289] devfreq soc:qcom,cpubw: Couldn't update frequency transition information.
[ 0.983272] devfreq soc:qcom,mincpubw: Couldn't update frequency transition information.
[ 0.992643] sensors-ssc soc:qcom,msm-ssc-sensors: msm_ssc_sensors_dt_parse: get qdsp timer cntpct hi offset fail
mounting devfs...
Cloudkey Recovery is starting up...
mounting proc...
mounting sysfs...
mounting run/tmp...
mounting devpts...
running /init.d:
/init.d/00-modules
/init.d/00-splash
/init.d/00-usb-otg
/init.d/01-mkdirs
/init.d/05-hostname
/init.d/09-wait-eth0
waiting for eth0... - took: 2s
/init.d/10-ifconfig
/init.d/20-mdev
/init.d/50-fwversion
Boottime: 4.52s
Ex
Please press Enter to activate this console.
Boottime: 4.52s
cloudkey-apq8053 login: ubnt
Password:
Login incorrect
cloudkey-apq8053 login: root
Password:
.--.__
______ __ .--( ) )-. __ __
| | (._____.__.___)_| | |__ _____ __ __
| ---| || _ | | | _ | <| -__| | |
|______|__||_____|_____|_____|__|__|_____|___ |
(c) 2018 Ubiquiti Networks, Inc. |_____|
Welcome to the CloudKey Recovery!
cloudkey-apq8053# dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.18.44-recovery (bdd@builder) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 SMP PREEMPT Mon Jun 18 02:24:21 PDT 2018
[ 0.000000] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000] alternatives: enabling workaround for ARM erratum 845719
[ 0.000000] Machine: Ubiquiti Networks, Inc. APQ8053 CloudKey Plus
[ 0.000000] Reserved memory: reserved region for node 'other_ext_region@0': base 0x0000000085b00000, size 13 MiB
[ 0.000000] Reserved memory: reserved region for node 'wcnss_fw_region@0': base 0x000000008e700000, size 7 MiB
[ 0.000000] Reserved memory: reserved region for node 'dfps_data_mem@90000000': base 0x0000000090000000, size 0 MiB
[ 0.000000] Removed memory: created DMA memory pool at 0x0000000085b00000, size 13 MiB
[ 0.000000] Reserved memory: initialized node other_ext_region@0, compatible id removed-dma-pool
[ 0.000000] Removed memory: created DMA memory pool at 0x000000008e700000, size 7 MiB
[ 0.000000] Reserved memory: initialized node wcnss_fw_region@0, compatible id removed-dma-pool
[ 0.000000] Reserved memory: allocated memory for 'venus_region@0' node: base 0x000000008f800000, size 8 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000008f800000, size 8 MiB
[ 0.000000] Reserved memory: initialized node venus_region@0, compatible id shared-dma-pool
[ 0.000000] Reserved memory: allocated memory for 'qseecom_region@0' node: base 0x00000000ff000000, size 16 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0x00000000ff000000, size 16 MiB
[ 0.000000] Reserved memory: initialized node qseecom_region@0, compatible id shared-dma-pool
[ 0.000000] cma: Reserved 16 MiB at 0x00000000fe000000
[ 0.000000] On node 0 totalpages: 781312
[ 0.000000] DMA zone: 12288 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 781312 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] PERCPU: Embedded 13 pages/cpu @ffffffc0bde61000 s21280 r0 d31968 u53248
[ 0.000000] pcpu-alloc: s21280 r0 d31968 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 769024
[ 0.000000] Kernel command line: sched_enable_hmp=1 sched_enable_power_aware=1 no_console_suspend console=ttyHSL0,115200n8 quiet gpt
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Memory: 3010268K/3125248K available (6926K kernel code, 784K rwdata, 2192K rodata, 352K init, 1432K bss, 114980K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB)
[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
[ 0.000000] 0xffffffbdc0000000 - 0xffffffbdc3000000 ( 48 MB actual)
[ 0.000000] PCI I/O : 0xffffffbffa000000 - 0xffffffbffb000000 ( 16 MB)
[ 0.000000] fixed : 0xffffffbffbdfd000 - 0xffffffbffbdff000 ( 8 KB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0c0000000 ( 3072 MB)
[ 0.000000] .init : 0xffffffc000970000 - 0xffffffc0009c8000 ( 352 KB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0007448b0 ( 6931 KB)
[ 0.000000] .data : 0xffffffc0009de000 - 0xffffffc000aa2190 ( 785 KB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] HMP scheduling enabled.
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000]
[ 0.000000] **********************************************************
[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000] ** **
[ 0.000000] ** trace_printk() being used. Allocating extra memory. **
[ 0.000000] ** **
[ 0.000000] ** This means that this is a DEBUG kernel and it is **
[ 0.000000] ** unsafe for produciton use. **
[ 0.000000] ** **
[ 0.000000] ** If you see this message and you are not debugging **
[ 0.000000] ** the kernel, report this immediately to your vendor! **
[ 0.000000] ** **
[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000] **********************************************************
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] mpm_init_irq_domain(): Cannot find irq controller for qcom,gpio-parent
[ 0.000000] Offload RCU callbacks from all CPUs
[ 0.000000] Offload RCU callbacks from CPUs: 0-7.
[ 0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
[ 0.000022] Switched to clocksource arch_sys_counter
[ 0.003305] allocated 12582912 bytes of page_cgroup
[ 0.003314] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.003329] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.003341] pid_max: default: 32768 minimum: 301
[ 0.003501] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.003516] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.004335] Initializing cgroup subsys blkio
[ 0.004351] Initializing cgroup subsys memory
[ 0.004373] Initializing cgroup subsys devices
[ 0.004386] Initializing cgroup subsys freezer
[ 0.005165] CPU0: update cpu_power 975
[ 0.005217] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.017124] MSM Memory Dump base table set up
[ 0.017151] MSM Memory Dump apps data table set up
[ 0.017209] Configuring XPU violations to be fatal errors
[ 0.018521] cpu_clock_pwr_init: Power clocks configured
[ 0.023859] CPU1: update cpu_power 975
[ 0.028863] CPU2: update cpu_power 975
[ 0.033840] CPU3: update cpu_power 975
[ 0.038876] CPU4: update cpu_power 1072
[ 0.043913] CPU5: update cpu_power 1072
[ 0.048907] CPU6: update cpu_power 1072
[ 0.053920] CPU7: update cpu_power 1072
[ 0.054133] Brought up 8 CPUs
[ 0.054167] SMP: Total of 8 processors activated.
[ 0.054254] alternatives: patching kernel code
[ 0.055185] devtmpfs: initialized
[ 0.059157] pinctrl core: initialized pinctrl subsystem
[ 0.059718] regulator-dummy: no parameters
[ 0.129826] NET: Registered protocol family 16
[ 0.132140] msm_pm_tz_boot_init: set warmboot address failed
[ 0.132177] scm_call failed: func id 0x42000101, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 0.150156] cpuidle: using governor ladder
[ 0.170137] cpuidle: using governor menu
[ 0.190136] cpuidle: using governor qcom
[ 0.190608] vdso: 2 pages (1 code @ ffffffc0009e5000, 1 data @ ffffffc0009e4000)
[ 0.191515] software IO TLB [mem 0xf7c00000-0xf8000000] (4MB) mapped at [ffffffc0b7c00000-ffffffc0b7ffffff]
[ 0.192762] DMA: preallocated 1024 KiB pool for atomic allocations
[ 0.200221] __of_mpm_init(): MPM driver mapping exists
[ 0.231176] sps:sps is ready.
[ 0.233705] msm_thermal:vdd_restriction_reg_init Defer regulator vdd-dig probe
[ 0.233728] msm-thermal soc:qcom,msm-thermal: probe_vdd_rstr:Failed reading node=/soc/qcom,msm-thermal, key=qcom,max-freq-level. err=-517. KTM continues
[ 0.238081] cpu-clock-8953 b114000.qcom,cpu-clock-8953: Speed bin: 2 PVS Version: 0
[ 0.239382] msm_rpm_glink_dt_parse: qcom,rpm-glink compatible not matches
[ 0.239392] msm_rpm_dev_probe: APSS-RPM communication over SMD
[ 0.242088] smd_channel_probe_now: allocation table 1 not initialized
[ 0.243475] smd_channel_probe_now: allocation table 4 not initialized
[ 0.244520] smd_channel_probe_now: allocation table 2 not initialized
[ 0.246245] msm_watchdog b017000.qcom,wdt: wdog absent resource not present
[ 0.246634] msm_watchdog b017000.qcom,wdt: MSM Watchdog Initialized
[ 0.256271] spmi_pmic_arb 200f000.qcom,spmi: PMIC Arb Version-2 0x20010000
[ 0.259935] pm8953_s5: 400 <--> 1140 mV at 870 mV normal idle
[ 0.260322] pm8953_s5_avs_limit: 400 <--> 1140 mV
[ 0.260507] spm_regulator_probe: name=pm8953_s5, range=LV, voltage=870000 uV, mode=AUTO, step rate=1200 uV/us
[ 0.265609] platform 1de0000.qcom,venus: assigned reserved memory node venus_region@0
[ 0.266361] platform a21b000.qcom,pronto: assigned reserved memory node wcnss_fw_region@0
[ 0.268581] apc_mem_acc_corner: 0 <--> 0 mV
[ 0.269741] cpr4_msm8953_apss_read_fuse_data: apc_corner: speed bin = 2
[ 0.269753] cpr4_msm8953_apss_read_fuse_data: apc_corner: CPR fusing revision = 3
[ 0.269763] cpr4_msm8953_apss_read_fuse_data: apc_corner: foundry id = 2
[ 0.269773] cpr4_msm8953_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 0.269809] cpr4_msm8953_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 0.269945] cpr4_msm8953_apss_calculate_open_loop_voltages: apc_corner: fused LowSVS: open-loop= 625000 uV
[ 0.269955] cpr4_msm8953_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 680000 uV
[ 0.269964] cpr4_msm8953_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 775000 uV
[ 0.269973] cpr4_msm8953_apss_calculate_open_loop_voltages: apc_corner: fused TURBO_L1: open-loop= 915000 uV
[ 0.270084] cpr4_msm8953_apss_calculate_target_quotients: apc_corner: fused LowSVS: quot[ 7]= 468
[ 0.270095] cpr4_msm8953_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 556, quot_offset[ 7]= 85
[ 0.270105] cpr4_msm8953_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 750, quot_offset[ 7]= 190
[ 0.270116] cpr4_msm8953_apss_calculate_target_quotients: apc_corner: fused TURBO_L1: quot[ 7]=1032, quot_offset[ 7]= 280
[ 0.270440] cpr4_apss_init_aging: apc: sensor 6 aging init quotient diff = -6, aging RO scale = 2800 QUOT/V
[ 0.270631] cpr3_regulator_init_ctrl: apc: Default CPR mode = HW closed-loop
[ 0.270805] apc_corner: 0 <--> 0 mV at 0 mV
[ 0.272083] gfx_mem_acc_corner: 0 <--> 0 mV
[ 0.290362] msm_thermal:sensor_mgr_init_threshold threshold id already initialized
[ 0.290503] msm_thermal:vdd_restriction_reg_init Defer regulator vdd-dig probe
[ 0.290520] msm-thermal soc:qcom,msm-thermal: probe_vdd_rstr:Failed reading node=/soc/qcom,msm-thermal, key=qcom,max-freq-level. err=-517. KTM continues
[ 0.290830] cpu-clock-8953 b114000.qcom,cpu-clock-8953: Speed bin: 2 PVS Version: 0
[ 0.290999] msm_rpm_glink_dt_parse: qcom,rpm-glink compatible not matches
[ 0.291009] msm_rpm_dev_probe: APSS-RPM communication over SMD
[ 0.291891] pm8953_s1: 870 <--> 1156 mV at 1000 mV normal idle
[ 0.292751] pm8953_s2_level: 0 <--> 0 mV at 0 mV normal idle
[ 0.293363] pm8953_s2_floor_level: 0 <--> 0 mV at 0 mV normal idle
[ 0.293939] pm8953_s2_level_ao: 0 <--> 0 mV at 0 mV normal idle
[ 0.294757] pm8953_s3: 1225 mV normal idle
[ 0.295552] pm8953_s4: 1900 <--> 2050 mV at 1900 mV normal idle
[ 0.296366] pm8953_s7_level: 0 <--> 0 mV at 0 mV normal idle
[ 0.296938] pm8953_s7_level_ao: 0 <--> 0 mV at 0 mV normal idle
[ 0.297542] pm8953_s7_level_so: 0 <--> 0 mV at 0 mV normal idle
[ 0.298321] pm8953_l1: 1000 <--> 1100 mV at 1000 mV normal idle
[ 0.299126] pm8953_l2: 975 <--> 1225 mV at 975 mV normal idle
[ 0.299907] pm8953_l3: 925 mV normal idle
[ 0.300746] pm8953_l5: 1800 mV normal idle
[ 0.301524] pm8953_l6: 1800 mV normal idle
[ 0.302330] pm8953_l7: 1800 <--> 1900 mV at 1800 mV normal idle
[ 0.302897] pm8953_l7_ao: 1800 <--> 1900 mV at 1800 mV normal idle
[ 0.303707] pm8953_l8: 2900 mV normal idle
[ 0.304498] pm8953_l9: 3000 <--> 3300 mV at 3000 mV normal idle
[ 0.305314] pm8953_l10: 2850 mV normal idle
[ 0.306094] pm8953_l11: 2950 mV normal idle
[ 0.306904] pm8953_l12: 1800 <--> 2950 mV at 1800 mV normal idle
[ 0.307684] pm8953_l13: 3125 mV normal idle
[ 0.308499] pm8953_l16: 1800 mV normal idle
[ 0.309276] pm8953_l17: 2850 mV normal idle
[ 0.310123] pm8953_l19: 1200 <--> 1350 mV at 1200 mV normal idle
[ 0.310908] pm8953_l22: 2800 <--> 2850 mV at 2800 mV normal idle
[ 0.311694] pm8953_l23: 975 <--> 1225 mV at 975 mV normal idle
[ 0.312361] GFX_LDO: msm_gfx_ldo_voltage_init: LDO corner 1: target-volt = 580000 uV
[ 0.312372] GFX_LDO: msm_gfx_ldo_voltage_init: LDO corner 2: target-volt = 650000 uV
[ 0.312382] GFX_LDO: msm_gfx_ldo_voltage_init: LDO corner 3: target-volt = 720000 uV
[ 0.312397] GFX_LDO: msm_gfx_ldo_adjust_init_voltage: adjusted the open-loop voltage[1] 580000 -> 615000
[ 0.312407] GFX_LDO: msm_gfx_ldo_adjust_init_voltage: adjusted the open-loop voltage[2] 650000 -> 675000
[ 0.312418] GFX_LDO: msm_gfx_ldo_voltage_init: LDO-mode fuse disabled by default
[ 0.312786] msm_gfx_ldo: 0 <--> 0 mV at 0 mV
[ 0.314337] msm_thermal:sensor_mgr_init_threshold threshold id already initialized
[ 0.315101] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.315112] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 0.315125] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.315134] msm_thermal:get_cpu_freq_plan_len Error reading CPU4 freq table len. error:-19
[ 0.315142] msm_thermal:vdd_restriction_reg_init Defer vdd rstr freq init.
[ 0.317252] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.317263] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 0.317275] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.317284] msm_thermal:get_cpu_freq_plan_len Error reading CPU4 freq table len. error:-19
[ 0.317296] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.317305] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 0.317315] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.317324] msm_thermal:get_cpu_freq_plan_len Error reading CPU4 freq table len. error:-19
[ 0.318251] qcom,gcc-8953 1800000.qcom,gcc: Venus speed bin: 2
[ 0.341743] branch_clk_handoff: gcc_usb_phy_cfg_ahb_clk clock is enabled in HW
[ 0.341755] branch_clk_handoff: even though ENABLE_BIT is not set
[ 0.343775] qcom,gcc-8953 1800000.qcom,gcc: Registered GCC clocks
[ 0.344015] cpu-clock-8953 b114000.qcom,cpu-clock-8953: Speed bin: 2 PVS Version: 0
[ 0.346637] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,dfs-sid-c0
[ 0.346651] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No DFS SID tables found for Cluster-0
[ 0.346664] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,link-sid-c0
[ 0.346676] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No Link SID tables found for Cluster-0
[ 0.346689] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,lmh-sid-c0
[ 0.346700] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No LMH SID tables found for Cluster-0
[ 0.346707] ramp_lmh_sid: Use Default LMH SID
[ 0.346714] ramp_dfs_sid: Use Default DFS SID
[ 0.346720] ramp_link_sid: Use Default Link SID
[ 0.346777] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,dfs-sid-c1
[ 0.346788] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No DFS SID tables found for Cluster-1
[ 0.346801] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,link-sid-c1
[ 0.346812] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No Link SID tables found for Cluster-1
[ 0.346824] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,lmh-sid-c1
[ 0.346835] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No LMH SID tables found for Cluster-1
[ 0.346842] ramp_lmh_sid: Use Default LMH SID
[ 0.346848] ramp_dfs_sid: Use Default DFS SID
[ 0.346855] ramp_link_sid: Use Default Link SID
[ 0.346917] clock_rcgwr_init: RCGwR Init Completed
[ 0.347449] populate_opp_table: clock-cpu-8953: OPP tables populated (cpu 3 and 7)
[ 0.347459] print_opp_table: clock_cpu: a53 C0: OPP voltage for 652800000: 1
[ 0.347467] print_opp_table: clock_cpu: a53 C0: OPP voltage for 2016000000: 7
[ 0.347475] print_opp_table: clock_cpu: a53 C1: OPP voltage for 652800000: 1
[ 0.347483] print_opp_table: clock_cpu: a53 C2: OPP voltage for 2016000000: 7
[ 0.349525] gcc-gfx-8953 1800000.qcom,gcc-gfx: Registered GCC GFX clocks.
[ 0.382230] qcom,qpnp-pin qpnp-pin-16: qpnp_pin_probe: no device nodes specified in topology
[ 0.382253] qcom,qpnp-pin: probe of qpnp-pin-16 failed with error -22
[ 0.382298] qcom,qpnp-pin qpnp-pin-17: qpnp_pin_probe: no device nodes specified in topology
[ 0.382314] qcom,qpnp-pin: probe of qpnp-pin-17 failed with error -22
[ 0.383882] KPI: Bootloader start count = 189205
[ 0.383893] KPI: Bootloader end count = 208130
[ 0.383900] KPI: Bootloader display count = 96351281
[ 0.383906] KPI: Bootloader load kernel count = 1163
[ 0.383914] KPI: Kernel MPM timestamp = 228749
[ 0.383920] KPI: Kernel MPM Clock frequency = 32768
[ 0.383948] socinfo_print: v0.10, id=304, ver=1.1, raw_id=102, raw_ver=1, hw_plat=250, hw_plat_ver=0
[ 0.383948] accessory_chip=0, hw_plat_subtype=0, pmic_model=65558, pmic_die_revision=65536 foundry_id=3 serial_number=3617218206
[ 0.385171] eldo2_8953: no parameters
[ 0.385567] qcom,qpnp-pin qpnp-pin-5: no such PMIC gpio 5 in device topology
[ 0.385712] adv_vreg: no parameters
[ 0.386718] txs0108e_oe: 1800 mV
[ 0.387164] hdd_vbus: 5000 mV
[ 0.387357] hdd_vbus: supplied by txs0108e_oe
[ 0.387794] usb_vbus: 5000 mV
[ 0.387902] usb_vbus: supplied by txs0108e_oe
[ 0.389652] SCSI subsystem initialized
[ 0.389736] libata version 3.00 loaded.
[ 0.390083] usbcore: registered new interface driver usbfs
[ 0.390142] usbcore: registered new interface driver hub
[ 0.390379] usbcore: registered new device driver usb
[ 0.391968] i2c-msm-v2 78b6000.i2c: probing driver i2c-msm-v2
[ 0.392278] AXI: msm_bus_scale_register_client(): Bus driver not ready.
[ 0.392289] i2c-msm-v2 78b6000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
[ 0.393303] i2c-msm-v2 7af5000.i2c: probing driver i2c-msm-v2
[ 0.393483] AXI: msm_bus_scale_register_client(): Bus driver not ready.
[ 0.393493] i2c-msm-v2 7af5000.i2c: msm_bus_scale_register_client(mstr-id:84):0 (not a problem)
[ 0.394642] EDAC MC: Ver: 3.0.0
[ 0.430367] cpufreq: driver msm up and running
[ 0.431011] platform soc:qcom,ion:qcom,ion-heap@27: assigned reserved memory node qseecom_region@0
[ 0.431306] ION heap system created
[ 0.431406] ION heap mm created at 0x00000000fe000000 with size 1000000
[ 0.431415] ION heap qsecom created at 0x00000000ff000000 with size 1000000
[ 0.441744] qcom,qpnp-power-on qpnp-power-on-1: PMIC@SID0 Power-on reason: Triggered from PON1 (secondary PMIC) and 'cold' boot
[ 0.441763] qcom,qpnp-power-on qpnp-power-on-1: PMIC@SID0: Unknown power-off reason
[ 0.441927] input: qpnp_pon as /devices/soc/qpnp-power-on-1/input/input0
[ 0.442508] pon_spare_reg: no parameters
[ 0.442569] qcom,qpnp-power-on qpnp-power-on-14: No PON config. specified
[ 0.442617] qcom,qpnp-power-on qpnp-power-on-14: PMIC@SID2 Power-on reason: Triggered from PON1 (secondary PMIC) and 'cold' boot
[ 0.442631] qcom,qpnp-power-on qpnp-power-on-14: PMIC@SID2: Unknown power-off reason
[ 0.442777] PMIC@SID0: (null) v1.0 options: 2, 2, 0, 0
[ 0.442871] PMIC@SID2: PMI8950 v2.0 options: 0, 0, 0, 0
[ 0.443343] gdsc_venus: no parameters
[ 0.443554] gdsc_mdss: no parameters
[ 0.443779] gdsc_jpeg: no parameters
[ 0.444121] gdsc_vfe: no parameters
[ 0.444479] gdsc_vfe1: no parameters
[ 0.444689] gdsc_cpp: no parameters
[ 0.444872] gdsc_oxili_gx: no parameters
[ 0.444947] gdsc_oxili_gx: supplied by msm_gfx_ldo
[ 0.445125] gdsc_venus_core0: fast normal
[ 0.445308] gdsc_oxili_cx: no parameters
[ 0.445451] gdsc_usb30: no parameters
[ 0.446164] mdss_pll_probe: MDSS pll label = MDSS DSI 0 PLL
[ 0.446170] mdss_pll_probe: mdss_pll_probe: label=MDSS DSI 0 PLL PLL SSC enabled
[ 0.446687] dsi_pll_clock_register_8996: Registered DSI PLL ndx=0 clocks successfully
[ 0.446711] mdss_pll_probe: MDSS pll label = MDSS DSI 1 PLL
[ 0.446715] mdss_pll_probe: mdss_pll_probe: label=MDSS DSI 1 PLL PLL SSC enabled
[ 0.447142] dsi_pll_clock_register_8996: Registered DSI PLL ndx=1 clocks successfully
[ 0.447501] msm_iommu 1e00000.qcom,iommu: device apps_iommu (model: 500) mapped at ffffff8001c80000, with 21 ctx banks
[ 0.453078] msm_iommu_ctx 1e20000.qcom,iommu-ctx: context adsp_elf using bank 0
[ 0.453237] msm_iommu_ctx 1e21000.qcom,iommu-ctx: context adsp_sec_pixel using bank 1
[ 0.453393] msm_iommu_ctx 1e22000.qcom,iommu-ctx: context mdp_1 using bank 2
[ 0.453552] msm_iommu_ctx 1e23000.qcom,iommu-ctx: context venus_fw using bank 3
[ 0.453709] msm_iommu_ctx 1e24000.qcom,iommu-ctx: context venus_sec_non_pixel using bank 4
[ 0.453867] msm_iommu_ctx 1e25000.qcom,iommu-ctx: context venus_sec_bitstream using bank 5
[ 0.454025] msm_iommu_ctx 1e26000.qcom,iommu-ctx: context venus_sec_pixel using bank 6
[ 0.454205] msm_iommu_ctx 1e28000.qcom,iommu-ctx: context pronto_pil using bank 8
[ 0.454393] msm_iommu_ctx 1e29000.qcom,iommu-ctx: context q6 using bank 9
[ 0.454574] msm_iommu_ctx 1e2a000.qcom,iommu-ctx: context periph_rpm using bank 10
[ 0.454753] msm_iommu_ctx 1e2b000.qcom,iommu-ctx: context lpass using bank 11
[ 0.454938] msm_iommu_ctx 1e2f000.qcom,iommu-ctx: context adsp_io using bank 15
[ 0.455117] msm_iommu_ctx 1e30000.qcom,iommu-ctx: context adsp_opendsp using bank 16
[ 0.455300] msm_iommu_ctx 1e31000.qcom,iommu-ctx: context adsp_shared using bank 17
[ 0.455480] msm_iommu_ctx 1e32000.qcom,iommu-ctx: context cpp using bank 18
[ 0.455660] msm_iommu_ctx 1e33000.qcom,iommu-ctx: context jpeg_enc0 using bank 19
[ 0.455845] msm_iommu_ctx 1e34000.qcom,iommu-ctx: context vfe using bank 20
[ 0.456030] msm_iommu_ctx 1e35000.qcom,iommu-ctx: context mdp_0 using bank 21
[ 0.456210] msm_iommu_ctx 1e36000.qcom,iommu-ctx: context venus_ns using bank 22
[ 0.456388] msm_iommu_ctx 1e38000.qcom,iommu-ctx: context ipa using bank 24
[ 0.456574] msm_iommu_ctx 1e37000.qcom,iommu-ctx: context access_control using bank 23
[ 0.459723] Bluetooth: Core ver 2.19
[ 0.459747] NET: Registered protocol family 31
[ 0.459751] Bluetooth: HCI device and connection manager initialized
[ 0.459760] Bluetooth: HCI socket layer initialized
[ 0.459768] Bluetooth: L2CAP socket layer initialized
[ 0.459788] Bluetooth: SCO socket layer initialized
[ 0.460218] Switched to clocksource arch_sys_counter
[ 0.477125] FS-Cache: Loaded
[ 0.477266] CacheFiles: Loaded
[ 0.479130] NET: Registered protocol family 2
[ 0.479493] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.479634] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.479908] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.479946] TCP: reno registered
[ 0.479953] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.480001] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.480197] NET: Registered protocol family 1
[ 0.480223] PCI: CLS 0 bytes, default 64
[ 0.481090] Trying to unpack rootfs image as initramfs...
[ 0.607087] Freeing initrd memory: 4980K (ffffffc003600000 - ffffffc003add000)
[ 0.610936] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.611389] vmscan: error setting kswapd cpu affinity mask
[ 0.616736] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.616908] msgmni has been set to 5969
[ 0.618934] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.619079] io scheduler noop registered
[ 0.619086] io scheduler deadline registered (default)
[ 0.619179] io scheduler cfq registered
[ 0.625400] msm_ipc_router_smd_driver_register Already driver registered IPCRTR
[ 0.625426] msm_ipc_router_smd_driver_register Already driver registered IPCRTR
[ 0.628823] In memshare_probe, Memshare probe success
[ 0.630684] msm_rpm_log_probe: OK
[ 0.632362] subsys-pil-tz 1de0000.qcom,venus: for venus segments only will be dumped.
[ 0.633882] msm_serial_hs module loaded
[ 0.634069] msm_serial_hsl_probe: detected port #0 (ttyHSL0)
[ 0.634142] msm_serial_hsl 78af000.serial: msm_bus_scale_pdata: qcom,msm-bus,name property not found
[ 0.634145] msm_serial_hsl_probe: Bus scaling is disabled
[ 0.634222] 78af000.serial: ttyHSL0 at MMIO 0x78af000 (irq = 167, base_baud = 460800) is a MSM
[ 0.634264] msm_hsl_console_setup: console setup on port #0
[ 0.726702] console [ttyHSL0] enabled
[ 0.726990] msm_serial_hsl_init: driver initialized
[ 0.732039] brd: module loaded
[ 0.734136] loop: module loaded
[ 0.734662] nbd: registered device at major 43
[ 0.738888] QSEECOM: qseecom_probe: qseecom.qsee_version = 0x1000000
[ 0.738913] QSEECOM: qseecom_retrieve_ce_data: Device does not support PFE
[ 0.738919] QSEECOM: qseecom_probe: qseecom clocks handled by other subsystem
[ 0.738923] QSEECOM: qseecom_probe: qsee reentrancy support phase is not defined, setting to default 0
[ 0.739435] QSEECOM: qseecom_probe: qseecom.whitelist_support = 1
[ 0.741623] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
[ 0.742130] qce 720000.qcedev: Qualcomm Crypto 5.3.3 device found @0x720000
[ 0.742139] qce 720000.qcedev: CE device = 0x0
[ 0.742139] , IO base, CE = 0xffffff8000640000
[ 0.742139] , Consumer (IN) PIPE 2, Producer (OUT) PIPE 3
[ 0.742139] IO base BAM = 0x (null)
[ 0.742139] BAM IRQ 185
[ 0.742139] Engines Availability = 0x2010853
[ 0.742330] sps:BAM 0x0000000000704000 is registered.
[ 0.742486] sps:BAM 0x0000000000704000 (va:0xffffff8001740000) enabled: ver:0x27, number of pipes:8
[ 0.742711] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000000704000 irq 185
[ 0.745472] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
[ 0.746225] qcrypto 720000.qcrypto: Qualcomm Crypto 5.3.3 device found @0x720000
[ 0.746233] qcrypto 720000.qcrypto: CE device = 0x0
[ 0.746233] , IO base, CE = 0xffffff80019c0000
[ 0.746233] , Consumer (IN) PIPE 4, Producer (OUT) PIPE 5
[ 0.746233] IO base BAM = 0x (null)
[ 0.746233] BAM IRQ 185
[ 0.746233] Engines Availability = 0x2010853
[ 0.746518] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000000704000 irq 185
[ 0.748673] qcrypto 720000.qcrypto: qcrypto-ecb-aes
[ 0.748755] qcrypto 720000.qcrypto: qcrypto-cbc-aes
[ 0.748837] qcrypto 720000.qcrypto: qcrypto-ctr-aes
[ 0.748919] qcrypto 720000.qcrypto: qcrypto-ecb-des
[ 0.749000] qcrypto 720000.qcrypto: qcrypto-cbc-des
[ 0.749082] qcrypto 720000.qcrypto: qcrypto-ecb-3des
[ 0.749163] qcrypto 720000.qcrypto: qcrypto-cbc-3des
[ 0.749247] qcrypto 720000.qcrypto: qcrypto-xts-aes
[ 0.749329] qcrypto 720000.qcrypto: qcrypto-sha1
[ 0.749411] qcrypto 720000.qcrypto: qcrypto-sha256
[ 0.749492] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-aes
[ 0.749575] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-des
[ 0.749663] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-3des
[ 0.749751] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-aes
[ 0.749833] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-des
[ 0.749916] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-3des
[ 0.750002] qcrypto 720000.qcrypto: qcrypto-hmac-sha1
[ 0.750184] qcrypto 720000.qcrypto: qcrypto-hmac-sha256
[ 0.750266] qcrypto 720000.qcrypto: qcrypto-aes-ccm
[ 0.750344] qcrypto 720000.qcrypto: qcrypto-rfc4309-aes-ccm
[ 0.750575] Loading iSCSI transport class v2.0-870.
[ 0.752727] sps: BAM device 0x0000000007884000 is not registered yet.
[ 0.752885] sps:BAM 0x0000000007884000 is registered.
[ 0.753421] sps:BAM 0x0000000007884000 (va:0xffffff8001720000) enabled: ver:0x19, number of pipes:12
[ 0.755028] m25p80 spi4.0: mx25l8005 (1024 Kbytes)
[ 0.755042] 1 ofpart partitions found on MTD device spi4.0
[ 0.755045] Creating 1 MTD partitions on "spi4.0":
[ 0.755052] 0x000000000000-0x000000010000 : "EEPROM"
[ 0.756584] wcnss_wlan probed in built-in mode
[ 0.757298] usbcore: registered new interface driver ax88179_178a
[ 0.757328] usbcore: registered new interface driver cdc_ether
[ 0.757356] usbcore: registered new interface driver cdc_subset
[ 0.757482] usbcore: registered new interface driver cdc_ncm
[ 0.757836] msm_sharedmem: sharedmem_register_qmi: qmi init successful
[ 0.758549] scm_call failed: func id 0x42000c16, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 0.765615] hyp_assign_table: Failed to assign memory protection, ret = -5
[ 0.765621] msm_sharedmem: setup_shared_ram_perms: hyp_assign_phys failed IPA=0x0160x00000000fe500000 size=1572864 err=-5
[ 0.776661] msm_sharedmem: msm_sharedmem_probe: Device created for client 'rmtfs'
[ 0.782003] msm-dwc3 7000000.ssusb: unable to get dbm device
[ 0.783097] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.783349] ehci-pci: EHCI PCI platform driver
[ 0.783381] ehci-msm: Qualcomm On-Chip EHCI Host Controller
[ 0.783656] usbcore: registered new interface driver uas
[ 0.783685] usbcore: registered new interface driver usb-storage
[ 0.784306] qcom,qpnp-rtc qpnp-rtc-8: rtc core: registered qpnp_rtc as rtc0
[ 0.784440] i2c /dev entries driver
[ 0.785323] power_supply ext_battery: ext_battery: Found supply : mains
[ 0.786692] TYPEC: qpnp_typec_probe: TypeC successfully probed state=0 CC-line-state=2
[ 0.787893] thermal thermal_zone0: failed to read out thermal zone 0
[ 0.788060] thermal thermal_zone1: failed to read out thermal zone 1
[ 0.788469] qpnp_vadc_read: no vadc_chg_vote found
[ 0.788473] qpnp_vadc_get_temp: VADC read error with -22
[ 0.788478] thermal thermal_zone2: failed to read out thermal zone 2
[ 0.809378] sdhci: Secure Digital Host Controller Interface driver
[ 0.809384] sdhci: Copyright(c) Pierre Ossman
[ 0.809396] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.810456] sdhci_msm 7824900.sdhci: sdhci_msm_probe: ICE device is not enabled
[ 0.810843] i2c-msm-v2 7af5000.i2c: msm_bus_scale_register_client(mstr-id:84):0x7 (ok)
[ 0.815146] sdhci_msm 7824900.sdhci: No vmmc regulator found
[ 0.815157] sdhci_msm 7824900.sdhci: No vqmmc regulator found
[ 0.815479] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using 64-bit ADMA in CMDQ mode
[ 0.834023] lp5562 5-0030: internal clock used
[ 0.836260] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.836434] usbcore: registered new interface driver usbhid
[ 0.836443] usbhid: USB HID core driver
[ 0.837472] fbtft_of_value: width = 160
[ 0.837485] fbtft_of_value: height = 60
[ 0.837498] fbtft_of_value: buswidth = 8
[ 0.837510] fbtft_of_value: bpp = 16
[ 0.837524] fbtft_of_value: rotate = 180
[ 0.837536] fbtft_of_value: fps = 100
[ 0.844744] sdhci_msm 7864900.sdhci: sdhci_msm_probe: ICE device is not enabled
[ 0.859689] sdhci_msm 7864900.sdhci: No vmmc regulator found
[ 0.859700] sdhci_msm 7864900.sdhci: No vqmmc regulator found
[ 0.860084] mmc1: SDHCI controller on 7864900.sdhci [7864900.sdhci] using 64-bit ADMA in legacy mode
[ 0.880997] mmc0: Out-of-interrupt timeout is 100[ms]
[ 0.881008] mmc0: BKOPS_EN equals 0x2
[ 0.881019] mmc0: eMMC FW version: 0x03
[ 0.881028] mmc0: CMDQ supported: depth: 16
[ 0.881038] mmc0: cache barrier support 0 flush policy 0
[ 0.889420] tz_log 8600720.tz-log: Hyp log service is not supported
[ 0.891943] cmdq_host_alloc_tdl: desc_size: 768 data_sz: 253952 slot-sz: 24
[ 0.892230] desc-base: 0xffffff8001991000 trans-base: 0xffffff8001b81000
[ 0.892230] desc_dma 0xfe127000 trans_dma: 0xfe480000
[ 0.892251] mmc0: CMDQ enabled on card
[ 0.892264] mmc0: new HS400 MMC card at address 0001
[ 0.892829] sdhci_msm_pm_qos_cpu_init (): voted for group #0 (mask=0xf) latency=2 (0xffffffc0b7437580)
[ 0.892842] sdhci_msm_pm_qos_cpu_init (): voted for group #1 (mask=0xf0) latency=2 (0xffffffc0b7437588)
[ 0.892999] mmcblk0: mmc0:0001 GX6BMB 29.1 GiB
[ 0.893217] mmcblk0rpmb: mmc0:0001 GX6BMB partition 3 4.00 MiB
[ 0.895270] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 p33 p34 p35 p36 p37 p38 p39 p40 p41 p42 p43 p44 p45 p46 p47
[ 0.970425] graphics fb0: fb_sp8110 frame buffer, 160x60, 18 KiB video memory, 16 KiB buffer memory, fps=100, spi3.0 at 19 MHz
[ 0.973316] bimc-bwmon 408000.qcom,cpu-bwmon: BW HWmon governor registered.
[ 0.976289] devfreq soc:qcom,cpubw: Couldn't update frequency transition information.
[ 0.983272] devfreq soc:qcom,mincpubw: Couldn't update frequency transition information.
[ 0.992643] sensors-ssc soc:qcom,msm-ssc-sensors: msm_ssc_sensors_dt_parse: get qdsp timer cntpct hi offset fail
[ 1.001788] sensors-ssc soc:qcom,msm-ssc-sensors: slpi_loader_init_sysfs: Could not parse dt
[ 1.002155] TCP: cubic registered
[ 1.002170] Initializing XFRM netlink socket
[ 1.002468] NET: Registered protocol family 10
[ 1.003143] NET: Registered protocol family 17
[ 1.003161] NET: Registered protocol family 15
[ 1.003239] Bluetooth: RFCOMM TTY layer initialized
[ 1.003247] Bluetooth: RFCOMM socket layer initialized
[ 1.003259] Bluetooth: RFCOMM ver 1.11
[ 1.003270] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.003273] Bluetooth: BNEP filters: protocol multicast
[ 1.003281] Bluetooth: BNEP socket layer initialized
[ 1.003287] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.003295] Bluetooth: HIDP socket layer initialized
[ 1.003909] NET: Registered protocol family 27
[ 1.005674] subsys-pil-tz a21b000.qcom,pronto: for wcnss segments only will be dumped.
[ 1.009190] sps:BAM 0x0000000007104000 is registered.
[ 1.012322] smbcharger_charger_otg: no parameters
[ 1.014451] msm-dwc3 7000000.ssusb: Avail curr from USB = 1500
[ 1.019737] qpnp-smbcharger qpnp-smbcharger-18: SMBCHG successfully probe Charger version=SCHG_LITE Revision DIG:0.0 ANA:0.1 batt=1 dc=0 usb=1
[ 1.020488] EDAC DEVICE0: Giving out device to module soc:arm64-cpu-erp controller cache: DEV soc:arm64-cpu-erp (INTERRUPT)
[ 1.020915] ARM64 CPU ERP: Could not find <cci-irq> IRQ property. Proceeding anyway.
[ 1.020919] ARM64 CPU ERP: SBE detection is disabled.
[ 1.021605] Registered cp15_barrier emulation handler
[ 1.021621] Registered setend emulation handler
[ 1.022141] registered taskstats version 1
[ 1.031590] input: gpio-keys as /devices/gpio_keys/input/input1
[ 1.031886] qcom,qpnp-rtc qpnp-rtc-8: setting system clock to 1970-01-01 00:00:07 UTC (7)
[ 1.032400] msm-core initialized without polling period
[ 1.036004] parse_cpu_levels: idx 1 276
[ 1.036015] calculate_residency: residency < 0 for LPM
[ 1.036208] parse_cpu_levels: idx 1 286
[ 1.036219] calculate_residency: residency < 0 for LPM
[ 1.042249] qcom,cc-debug-8953 1874000.qcom,cc-debug: Registered Debug Mux successfully
[ 1.042437] apc_mem_acc_corner: disabling
[ 1.042444] gfx_mem_acc_corner: disabling
[ 1.042484] adv_vreg: disabling
[ 1.042489] Unable to find log_buf by kallsyms!
[ 1.042549] clock_late_init: Removing enables held for handed-off clocks
[ 1.048251] Freeing unused kernel memory: 352K (ffffffc000970000 - ffffffc0009c8000)
[ 1.048278] Freeing alternatives memory: 64K (ffffffc0009c8000 - ffffffc0009d8000)
[ 1.053003] cpr3_regulator_measure_aging: apc: average quotient delta=-4 (count=10)
[ 1.053023] cpr3_regulator_aging_adjust: apc: aging measurement successful; aging reference adjustment voltage=714 uV
[ 1.131447] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 1.131503] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 1.131671] xhci-hcd xhci-hcd.0.auto: irq 521, io mem 0x07000000
[ 1.133292] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.133311] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.133327] usb usb1: Product: xHCI Host Controller
[ 1.133341] usb usb1: Manufacturer: Linux 3.18.44-recovery xhci-hcd
[ 1.133355] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 1.134526] hub 1-0:1.0: USB hub found
[ 1.134604] hub 1-0:1.0: 1 port detected
[ 1.135228] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 1.135255] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 1.135775] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.135792] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.135806] usb usb2: Product: xHCI Host Controller
[ 1.135820] usb usb2: Manufacturer: Linux 3.18.44-recovery xhci-hcd
[ 1.135833] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 1.136854] hub 2-0:1.0: USB hub found
[ 1.136925] hub 2-0:1.0: 1 port detected
[ 1.450652] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 1.480992] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 1.501290] usb 2-1: New USB device found, idVendor=0451, idProduct=8440
[ 1.501316] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.504489] hub 2-1:1.0: USB hub found
[ 1.504637] hub 2-1:1.0: 4 ports detected
[ 1.591024] usb 1-1: New USB device found, idVendor=0451, idProduct=8442
[ 1.591047] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 1.591062] usb 1-1: SerialNumber: 7C0E10797D53
[ 1.616022] hub 1-1:1.0: USB hub found
[ 1.616157] hub 1-1:1.0: 6 ports detected
[ 1.780940] usb 2-1.2: new SuperSpeed USB device number 3 using xhci-hcd
[ 1.803482] usb 2-1.2: New USB device found, idVendor=174c, idProduct=1153
[ 1.803509] usb 2-1.2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 1.803525] usb 2-1.2: Product: ASM1153E
[ 1.803538] usb 2-1.2: Manufacturer: ASMT
[ 1.803552] usb 2-1.2: SerialNumber: 05904154500600000003
[ 1.816185] scsi host0: uas
[ 1.817209] scsi 0:0:0:0: Direct-Access ASMT 2115 0 PQ: 0 ANSI: 6
[ 1.821385] xhci-hcd xhci-hcd.0.auto: ERROR Transfer event for disabled endpoint or incorrect stream ring
[ 1.821394] xhci-hcd xhci-hcd.0.auto: @00000000fe14c8e0 00000000 00000000 1b000000 03038001
[ 1.940819] usb 1-1.5: new high-speed USB device number 4 using xhci-hcd
[ 2.041611] usb 1-1.5: New USB device found, idVendor=0451, idProduct=82ff
[ 2.041638] usb 1-1.5: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 2.041655] usb 1-1.5: SerialNumber: 7C0E10797D53
[ 2.067731] hid-generic 0003:0451:82FF.0001: hiddev0,hidraw0: USB HID v1.11 Device [HID 0451:82ff] on usb-xhci-hcd.0.auto-1.5/input0
[ 2.091396] usb 2-1.1: new SuperSpeed USB device number 4 using xhci-hcd
[ 2.122496] usb 2-1.1: New USB device found, idVendor=0b95, idProduct=1790
[ 2.122511] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.122521] usb 2-1.1: Product: AX88179
[ 2.122530] usb 2-1.1: Manufacturer: ASIX Elec. Corp.
[ 2.122539] usb 2-1.1: SerialNumber: 00000000000001
[ 2.229172] sda: sda1 sda2 sda3 sda4
[ 2.513480] ASIX USB Ethernet Adapter:v1.16.0 http://www.asix.com.tw
[ 2.513505] ax88179_178a 2-1.1:1.0 (unnamed net_device) (uninitialized): mtu 1500
[ 2.514300] ax88179_178a 2-1.1:1.0 eth0: register 'ax88179_178a' at usb-xhci-hcd.0.auto-1.1, ASIX AX88179 USB 3.0 Gigabit Ethernet, ffffffc0b6d7cb10
[ 3.430334] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.030151] msm-dwc3 7000000.ssusb: Avail curr from USB = 1800
[ 4.162602] random: nonblocking pool is initialized
[ 4.320761] power_supply ext_battery: external power changed: 1
[ 4.320773] power_supply ext_battery: disabling battery booster
[ 4.915603] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.919523] ax88179_178a 2-1.1:1.0 eth0: ax88179_178a - Link status is: 1
[ 7.921907] ax88179_178a 2-1.1:1.0 eth0: Write medium type: 0x003b
[ 7.924451] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.925835] ax88179_178a 2-1.1:1.0 eth0: link up, 1000Mbps, full-duplex, lpa 0xC5E1