💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc1997.txt captured on 2023-01-29 at 07:02:11.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group R. Chandra
Request for Comments: 1997 P. Traina
Category: Standards Track cisco Systems
T. Li
August 1996
BGP Communities Attribute
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Abstract
Border Gateway Protocol [1] is an inter-autonomous system routing
protocol designed for TCP/IP internets.
This document describes an extension to BGP which may be used to pass
additional information to both neighboring and remote BGP peers.
The intention of the proposed technique is to aid in policy
administration and reduce the management complexity of maintaining
the Internet.
Introduction
BGP supports transit policies via controlled distribution of routing
information. Mechanisms for this are described in [1] and have been
successfully used by transit service providers. However, control
over the distribution of routing information is presently based on
either IP address prefixes or on the value of the AS_PATH attribute
(or part of it).
To facilitate and simplify the control of routing information this
document suggests a grouping of destinations so that the routing
decision can also be based on the identity of a group. Such a scheme
is expected to significantly simplify a BGP speaker's configuration
that controls distribution of routing information.
Chandra, et. al. Standards Track [Page 1]
RFC 1997 BGP Communities Attribute August 1996
Terms and Definitions
Community
A community is a group of destinations which share some common
property.
Each autonomous system administrator may define which communities
a destination belongs to. By default, all destinations belong to
the general Internet community.
Examples
A property such as "NSFNET sponsored/AUP" could be added to all AUP
compliant destinations advertised into the NSFNET. NSFNET operators
could define a policy that would advertise all routes, tagged or not,
to directly connected AUP compliant customers and only tagged routes
to commercial or external sites. This would insure that at least one
side of a given connection is AUP compliant as a way of enforcing NSF
transit policy guidelines.
In this example, we have just eliminated the primary motivation for a
complex policy routing database that is used to generate huge prefix
and AS path based filter rules. We have also eliminated the delays
caused by the out-of-band maintenance of this database (mailing in
NACRs, weekly configuration runs, etc.)
A second example comes from experience with aggregation. It is often
useful to advertise both an aggregate prefix and the component more-
specific prefixes that were used to form the aggregate to optimize
"next hop" routing. These component prefixes are only useful to the
neighboring BGP peer or perhaps the autonomous system of the
neighboring BGP peer, so it is desirable to filter this information.
By specifying a community value that the neighboring peer or peers
will match and filter on, these more specific routes may be
advertised with the assurance that they will not propagate beyond
their desired scope.
COMMUNITIES attribute
This document creates the COMMUNITIES path attribute is an optional
transitive attribute of variable length. The attribute consists of a
set of four octet values, each of which specify a community. All
routes with this attribute belong to the communities listed in the
attribute.
The COMMUNITIES attribute has Type Code 8.
Chandra, et. al. Standards Track [Page 2]
RFC 1997 BGP Communities Attribute August 1996
Communities are treated as 32 bit values, however for administrative
assignment, the following presumptions may be made:
The community attribute values ranging from 0x0000000 through
0x0000FFFF and 0xFFFF0000 through 0xFFFFFFFF are hereby reserved.
The rest of the community attribute values shall be encoded using an
autonomous system number in the first two octets. The semantics of
the final two octets may be defined by the autonomous system (e.g. AS
690 may define research, educational and commercial community values
that may be used for policy routing as defined by the operators of
that AS using community attribute values 0x02B20000 through
0x02B2FFFF).
Well-known Communities
The following communities have global significance and their
operations shall be implemented in any community-attribute-aware BGP
speaker.
NO_EXPORT (0xFFFFFF01)
All routes received carrying a communities attribute
containing this value MUST NOT be advertised outside a BGP
confederation boundary (a stand-alone autonomous system that
is not part of a confederation should be considered a
confederation itself).
NO_ADVERTISE (0xFFFFFF02)
All routes received carrying a communities attribute
containing this value MUST NOT be advertised to other BGP
peers.
NO_EXPORT_SUBCONFED (0xFFFFFF03)
All routes received carrying a communities attribute
containing this value MUST NOT be advertised to external BGP
peers (this includes peers in other members autonomous
systems inside a BGP confederation).
Operation
A BGP speaker may use this attribute to control which routing
information it accepts, prefers or distributes to other neighbors.
A BGP speaker receiving a route that does not have the COMMUNITIES
path attribute may append this attribute to the route when
propagating it to its peers.
A BGP speaker receiving a route with the COMMUNITIES path attribute
may modify this attribute according to the local policy.
Chandra, et. al. Standards Track [Page 3]
RFC 1997 BGP Communities Attribute August 1996
Aggregation
If a range of routes is to be aggregated and the resultant aggregates
attribute section does not carry the ATOMIC_AGGREGATE attribute, then
the resulting aggregate should have a COMMUNITIES path attribute
which contains all communities from all of the aggregated routes.
Applicability
The COMMUNITIES path attribute may be used with BGP version 2 and all
subsequent versions of BGP unless specifically noted otherwise.
Security Considerations
Security issues are not discussed in this memo.
Acknowledgments
We'd like to thank Vince Fuller, Sean Doran, and Andrew Partan for
bringing to our attention the problems that we believe the BGP
communities attribute will help solve. We'd also like to thank Yakov
Rekhter his review of this document as well as his constructive and
valuable comments.
Authors' Addresses
Paul Traina
cisco Systems, Inc.
170 W. Tasman Dr.
San Jose, CA 95134
EMail: pst@cisco.com
Ravishanker Chandrasekeran
(Ravi Chandra)
cisco Systems, Inc.
170 W. Tasman Dr.
San Jose, CA 95134
EMail: rchandra@cisco.com
Tony Li
EMail: tli@skat.usc.edu
Chandra, et. al. Standards Track [Page 4]
RFC 1997 BGP Communities Attribute August 1996
References
[1] RFC 1771
Rekhter, Y., and T. Li, "A Border Gateway Protocol 4 (BGP-4)",
March 1995.
[2] RFC 1965
Traina, P., "Autonomous System Confederations for BGP", June 1996.
Chandra, et. al. Standards Track [Page 5]