💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc1742.txt captured on 2023-01-29 at 07:07:20.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group S. Waldbusser
Request for Comments: 1742 Carnegie Mellon University
Obsoletes: 1243 K. Frisa
Category: Standards Track FORE Systems, Inc.
January 1995
AppleTalk Management Information Base II
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in TCP/IP-based internets.
In particular, it defines objects for managing AppleTalk networks.
RFC 1243 defines a set of MIB objects for managing the lower layers
of the AppleTalk protocol stack, up to the Network layer. This memo
defines additional objects that exist in the AppleTalk portion of the
MIB. These objects provide for the management of the transport and
session layers of the AppleTalk protocol stack, as well as extensions
to the lower layers. This is achieved in an upwardly-compatable
fashion.
Table of Contents
1. The Network Management Framework ...................... 2
2. Additions and Changes ................................. 3
2.1 New Groups ........................................... 3
2.2 Additional Variables ................................. 3
2.2.1 AARP Additions ..................................... 3
2.2.2 ATPort Additions ................................... 3
2.2.3 DDP Addition ....................................... 3
2.2.4 RTMP Additions ..................................... 4
2.2.5 KIP Addition ....................................... 4
2.2.6 ZIP Additions ...................................... 4
2.2.7 NBP Additions ...................................... 4
2.2.8 ATEcho Additions ................................... 4
2.3 Deprecations ......................................... 4
2.4 Changes .............................................. 5
3. Objects ............................................... 6
Waldbusser & Frisa [Page 1]
RFC 1742 AppleTalk MIB II January 1995
3.1 Format of Definitions ................................ 6
4. Overview .............................................. 6
4.1 Structure of MIB ..................................... 7
4.2 The LocalTalk Link Access Protocol Group ............. 7
4.3 The AppleTalk Address Resolution Protocol Group ...... 7
4.4 The AppleTalk Port Group ............................. 8
4.5 The Datagram Delivery Protocol Group ................. 8
4.6 The Datagram Delivery Protocol Router Group .......... 8
4.7 The Routing Table Maintenance Protocol Group ......... 8
4.8 The Routing Table Maintenance Protocol Stub Group .... 8
4.9 The Kinetics Internet Protocol Group ................. 8
4.10 The Zone Information Protocol Router Group .......... 9
4.11 The Zone Information Protocol End Node Group ........ 9
4.12 The Name Binding Protocol Group ..................... 9
4.13 The AppleTalk Echo Protocol Group ................... 9
4.14 The AppleTalk Transaction Protocol Group ............ 9
4.15 The Printer Access Protocol Group ................... 9
4.16 The AppleTalk Session Protocol Group ................ 9
4.17 The AppleTalk Data Stream Protocol Group ............ 10
4.18 The AppleTalk Port Point to Point Group ............. 10
4.19 The Per Port Counters Group ......................... 10
4.20 Textual Conventions ................................. 10
5. Definitions ........................................... 11
6. Acknowledgmnts ........................................ 82
7. References ............................................ 83
8. Security Considerations ............................... 84
9. Authors' Addresses .................................... 84
1. The Network Management Framework
The Internet-standard Network Management Framework consists of three
components. They are:
STD 16/RFC 1155 which defines the SMI, the mechanisms used for
describing and naming objects for the purpose of management.
STD 16/RFC 1212 defines a more concise description mechanism,
which is wholly consistent with the SMI.
RFC 1156 which defines MIB-I, the core set of managed objects for
the Internet suite of protocols. STD 17/RFC 1213 defines MIB-
II, an evolution of MIB-I based on implementation experience
and new operational requirements.
STD 15/RFC 1157 which defines the SNMP, the protocol used for
network access to managed objects.
Waldbusser & Frisa [Page 2]
RFC 1742 AppleTalk MIB II January 1995
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
2. Additions and Changes
This MIB includes additions and changes to RFC 1243. These changes
are outlined in the following sections.
2.1. New Groups
The following groups are introduced in this MIB:
- DDP Router
- RTMP Stub
- ZIP Router
- ATP
- PAP
- ASP
- ADSP
- ATPortPtoP
- Per Port Counters
2.2. Additional Variables
Many variables, mostly counters, were added to groups that existed in
RFC 1243. These variables are listed in the following sections.
2.2.1. AARP Additions
aarpStatus
aarpLookups
aarpHits
2.2.2. ATPort Additions
atportNetFrom
atportZoneFrom
atportInPkts
atportOutPkts
atportHome
atportCurrentZone
atportConflictPhysAddr
atportZoneTable
2.2.3. DDP Addition
ddpListenerTable
Waldbusser & Frisa [Page 3]
RFC 1742 AppleTalk MIB II January 1995
2.2.4. RTMP Additions
rtmpInDataPkts
rtmpOutDataPkts
rtmpInRequestPkts
rtmpNextIREqualChanges
rtmpNextIRLessChanges
rtmpRouteDeletes
rtmpRoutingTableOverflows
2.2.5. KIP Addition
kipFrom
2.2.6. ZIP Additions
zipNetInfoTable
zipInErrors
2.2.7. NBP Additions
nbpAddress
nbpSocket
nbpEnumerator
nbpInLookUpRequests
nbpInLookUpReplies
nbpInBroadcastRequests
nbpInForwardRequests
nbpOutLookUpReplies
nbpRegistrationFailures
nbpInErrors
2.2.8. ATEcho Additions
atechoOutRequests
atechoInReplies
2.3. Deprecations
The following variables have been deprecated in this version of the
MIB:
llapInPkts
llapOutPkts
llapInNoHandlers
llapInErrors
Waldbusser & Frisa [Page 4]
RFC 1742 AppleTalk MIB II January 1995
These llap variables were duplicated in the interfaces table of MIB-
II.
2.4. Changes
The IMPORTS list has been updated to reflect the current SNMP
documents.
New textual conventions have been defined.
Hyphens have been removed from enumeration strings.
Variables used as INDEXes to new tables have ACCESS not-accessible.
This is because the values of the INDEX variables are contained in
the object identifier for any of the other variables in the table;
therefore, it does not need to be explicitly available as data.
The atportNetConfig and atportZoneConfig variables have been changed
from read-only to read-write.
The atportZone variable has be renamed to atportZoneDefault, and its
DESCRIPTION clause has been clarified.
The atportType, atportStatus, and kipType variables have had more
values added to their enumeration lists.
The DDP group has been split into two groups; one includes variables
that any AppleTalk node would implement and the other includes
variables only a router would implement.
The rtmpState variable now includes another enumeration, invalid(5),
which is used when deleting rows.
The variables rtmpRangeStart, rtmpRangeEnd, rtmpNextHop, rtmpType,
rtmpPort, and rtmpHops have been changed from read-write to read-
only.
The ZIP Group has been renamed the ZIP End Node Group.
The DESCRIPTION clause for zipZoneIndex has been clarified.
The variables zipZoneName, zipZoneNetStart, and zipZoneNetEnd have
been changed from read-write to read-only.
The nbpIndex variable has been changed from read-only to read-write.
The nbpObject, nbpType, and nbpZone variables now suggest that the
agent reregister its service when any of these variables is changed.
Waldbusser & Frisa [Page 5]
RFC 1742 AppleTalk MIB II January 1995
The nbpState variable includes new enumerations.
3. Objects
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the subset of Abstract Syntax Notation One (ASN.1) [7]
defined in the SMI. In particular, each object has a name, a syntax,
and an encoding. The name is an object identifier, an
administratively assigned name, which specifies an object type. The
object type together with an object instance serves to uniquely
identify a specific instantiation of the object. For human
convenience, we often use a textual string, termed the OBJECT
DESCRIPTOR, to also refer to the object type.
The syntax of an object type defines the abstract data structure
corresponding to that object type. The ASN.1 language is used for
this purpose. However, the SMI [3] purposely restricts the ASN.1
constructs which may be used. These restrictions are explicitly made
for simplicity.
The encoding of an object type is simply how that object type is
represented using the object type's syntax. Implicitly tied to the
notion of an object type's syntax and encoding is how the object type
is represented when being transmitted on the network.
The SMI specifies the use of the basic encoding rules of ASN.1 [8],
subject to the additional requirements imposed by the SNMP.
3.1. Format of Definitions
Section 5 contains the specification of all object types contained in
this MIB module. The object types are defined using the conventions
defined in the SMI, as amended by the extensions specified in [9].
4. Overview
AppleTalk is a protocol suite which features an open peer-to-peer
architecture that runs over a variety of transmission media.
AppleTalk is defined in [10]. This protocol suite interoperates with
the IP protocol suite through various encapsulation methods. As
large AppleTalk networks are built that coexist with large IP
networks, a method to manage the AppleTalk networks with SNMP becomes
necessary. This MIB defines managed objects to be used for managing
AppleTalk networks.
Waldbusser & Frisa [Page 6]
RFC 1742 AppleTalk MIB II January 1995
4.1. Structure of MIB
The objects are arranged into the following groups:
- LLAP
- AARP
- ATPort
- DDP
- DDP Router
- RTMP
- RTMP Stub
- KIP
- ZIP Router
- ZIP End Node
- NBP
- ATEcho
- ATP
- PAP
- ASP
- ADSP
- ATPortPtoP
- Per Port Counters
These groups are the basic unit of conformance. If the semantics of a
group is applicable to an implementation, then it must implement all
objects in that group. For example, a managed agent must implement
the KIP group if and only if it implements the KIP protocol.
These groups are defined to provide a method for managed agents to
know which objects they must implement.
4.2. The LocalTalk Link Access Protocol Group
The LocalTalk Link Access Protocol (LLAP) is a medium-speed data-link
protocol designed for low cost and plug-and-play operation. The LLAP
group is designed to manage all interfaces on a managed device that
use this protocol.
4.3. The AppleTalk Address Resolution Protocol Group
The AppleTalk Address Resolution Protocol (AARP) is used to map
between AppleTalk node addresses, used by the Datagram Delivery
Protocol, and the addresses of the underlying data link layer. The
AARP table allows for management of the Address Mapping Table on the
managed device.
Waldbusser & Frisa [Page 7]
RFC 1742 AppleTalk MIB II January 1995
4.4. The AppleTalk Port Group
An AppleTalk Port is a logical connection to a network over which
AppleTalk packets can be transmitted. The "network" could be a
tunnel, backbone network, point-to-point link, etc, as well as a
native AppleTalk network. This group allows the management of the
configuration of these AppleTalk ports.
4.5. The Datagram Delivery Protocol Group
The Datagram Delivery Protocol (DDP) is the network-layer protocol
that is responsible for the socket-to-socket delivery of datagrams
over the AppleTalk Internet. This group manages the DDP layer on the
managed device.
The DDP group contains statistical counters for the DDP protocol, and
a table describing the DDP sockets that have protocol handlers
registered.
4.6. The Datagram Delivery Protocol Router Group
Some variables relevant to the Datagram Delivery Protocol (DDP) are
only applicable to AppleTalk routers. These variables are included
in this group.
4.7. The Routing Table Maintenance Protocol Group
The Routing Table Maintenance Protocol (RTMP) is used by AppleTalk
routers to create and maintain the routing tables that dictate the
process of forwarding datagrams on the AppleTalk internet. The RTMP
group manages the RTMP protocol as well as the routing tables
generated by this protocol.
4.8. The Routing Table Maintenance Protocol Stub Group
The RTMP Stub process is implemented by end nodes in order to
maintain information about the routers on their networks. The
variables in this group apply to both routers and end nodes. This
group manages the RTMP stub process.
4.9. The Kinetics Internet Protocol Group
The Kinetics Internet Protocol (KIP) is a protocol for encapsulating
and routing AppleTalk datagrams over an IP internet. This name is
historical. The KIP group manages the KIP routing protocol as well
as the routing tables generated by this protocol.
Waldbusser & Frisa [Page 8]
RFC 1742 AppleTalk MIB II January 1995
4.10. The Zone Information Protocol Router Group
The Zone Information Protocol (ZIP) is used to maintain a mapping
between networks and zone names to facilitate the name lookup process
performed by the Name Binding Protocol. Some variables relevant to
the Zone Information Protocol (ZIP) are only applicable to AppleTalk
routers. These variables are included in this group.
4.11. The Zone Information Protocol End Node Group
The ZIP End Node group manages the variables relevant to the Zone
Information Protocol (ZIP) that are applicable to both routers and
end nodes.
4.12. The Name Binding Protocol Group
The Name Binding Protocol (NBP) is a transport-level protocol that is
used to convert human readable service names into the numeric
AppleTalk network addresses needed for communicating across the
AppleTalk network. The NBP group manages this protocol and the NBP
services that exist on the managed device.
4.13. The AppleTalk Echo Protocol Group
The AppleTalk Echo Protocol is a transport-level protocol used to
test and verify the status of the AppleTalk internet. The AtEcho
group manages this protocol.
4.14. The AppleTalk Transaction Protocol Group
The AppleTalk Transaction Protocol (ATP) is a transport-level
protocol that is defined to support transaction based communications.
The ATP group manages this protocol.
4.15. The Printer Access Protocol Group
The Printer Access Protocol (PAP) is a session-level protocol that
enables communications between workstations and print servers. The
PAP group manages this protocol.
4.16. The AppleTalk Session Protocol Group
The AppleTalk Session Protocol (ASP) is a session-level protocol that
enables sequences of communications to occur. ASP uses the services
of the AppleTalk Transaction Protocol (ATP), but extends these
services into the session layer. The ASP group manages this
protocol.
Waldbusser & Frisa [Page 9]
RFC 1742 AppleTalk MIB II January 1995
4.17. The AppleTalk Data Stream Protocol Group
The AppleTalk Data Stream Protocol (ADSP) is a session-level protocol
that provides symmetric, connection-oriented, full-duplex
communication between two sockets on the AppleTalk internet. In
addition, ADSP handles flow-control and reliability. The ADSP group
manages this protocol.
4.18. The AppleTalk Port Point to Point Group
The AppleTalk Port Point to Point Group manages ports that have one
or more associated point-to-point connections.
4.19. The Per Port Counters Group
The Per Port Counters Group contains a set of counters which are
deemed useful on a per port basis.
4.20. Textual Conventions
New data types are introduced as textual conventions in this MIB
document. These textual conventions enhance the readability of the
specification and can ease comparison with other specifications if
appropriate. It should be noted that the introduction of these
textual conventions has no effect on either the syntax or the
semantics of any managed objects. The use of this is merely an
artifact of the explanatory method used. Objects defined in terms of
this method are always encoded by means of the rules that define the
primitive type. Hence, no changes to the SMI or the SNMP are
necessary to accommodate these textual conventions which are adopted
merely for the convenience of readers and writers in pursuit of the
elusive goal of clear, concise, and unambiguous MIB documents.
The new data types are:
ATNetworkNumber ::= -- 2 octets of network
-- number in network
-- byte order
OCTET STRING (SIZE (2))
DdpNodeAddress ::= -- 2 octets of net number
-- in network byte order,
-- 1 octet of node number
OCTET STRING (SIZE (3))
DdpSocketAddress ::= -- 2 octets of net number
-- in network byte order,
-- 1 octet of node number,
Waldbusser & Frisa [Page 10]
RFC 1742 AppleTalk MIB II January 1995
-- 1 octet of socket
-- number (0..255)
OCTET STRING (SIZE (4))
ATName ::= -- 0 to 32 octets of
-- AppleTalk ASCII [10]
OCTET STRING (SIZE (0..32))
5. Definitions
APPLETALK-MIB DEFINITIONS ::= BEGIN
IMPORTS
Counter, IpAddress, TimeTicks
FROM RFC1155-SMI
DisplayString, mib-2
FROM RFC1213-MIB
OBJECT-TYPE
FROM RFC-1212;
-- This MIB module uses the extended OBJECT-TYPE macro as
-- defined in RFC-1212.
-- The following reference is used in this MIB:
-- [Inside AppleTalk]
-- This refers to Gursharan S. Sidhu, Richard F. Andrews, and
-- Alan B. Oppenheimer, Inside AppleTalk, Second Edition,
-- Addison Wesley, (1990).
-- AppleTalk MIB
appletalk OBJECT IDENTIFIER ::= { mib-2 13 }
ATNetworkNumber ::= -- 2 octets of net number
-- in network byte order
OCTET STRING (SIZE (2))
DdpNodeAddress ::= -- 2 octets of net number
-- in network byte order,
-- 1 octet of node number
OCTET STRING (SIZE (3))
DdpSocketAddress ::= -- 2 octets of net number
-- in network byte order,
-- 1 octet of node number,
Waldbusser & Frisa [Page 11]
RFC 1742 AppleTalk MIB II January 1995
-- 1 octet of socket number
-- (0..255)
OCTET STRING (SIZE (4))
ATName ::= -- 0 to 32 octets of AppleTalk
-- ASCII [Inside AppleTalk]
OCTET STRING (SIZE (0..32))
llap OBJECT IDENTIFIER ::= { appletalk 1 }
aarp OBJECT IDENTIFIER ::= { appletalk 2 }
atport OBJECT IDENTIFIER ::= { appletalk 3 }
ddp OBJECT IDENTIFIER ::= { appletalk 4 }
rtmp OBJECT IDENTIFIER ::= { appletalk 5 }
kip OBJECT IDENTIFIER ::= { appletalk 6 }
zipRouter OBJECT IDENTIFIER ::= { appletalk 7 }
nbp OBJECT IDENTIFIER ::= { appletalk 8 }
atecho OBJECT IDENTIFIER ::= { appletalk 9 }
atp OBJECT IDENTIFIER ::= { appletalk 10 }
pap OBJECT IDENTIFIER ::= { appletalk 11 }
asp OBJECT IDENTIFIER ::= { appletalk 12 }
adsp OBJECT IDENTIFIER ::= { appletalk 13 }
atportptop OBJECT IDENTIFIER ::= { appletalk 14 }
rtmpStub OBJECT IDENTIFIER ::= { appletalk 16 }
zipEndNode OBJECT IDENTIFIER ::= { appletalk 17 }
perPort OBJECT IDENTIFIER ::= { appletalk 18 }
-- The LLAP Group
--
-- Implementation of this group is mandatory for all
-- entities that implement LLAP
--
-- Notes for the interfaces group
--
-- When implementing the Interfaces Group of MIB-II, it is
-- suggested that the following values be used for any
-- LocalTalk interfaces:
-- ifMtu: 600
-- ifSpeed: 230000
-- ifPhysAddress: the one octet node number for the
-- particular interface
--
-- Note also that LLAP control packets should not be
-- included in the Interfaces Group packet or octet
-- counters.
Waldbusser & Frisa [Page 12]
RFC 1742 AppleTalk MIB II January 1995
llapTable OBJECT-TYPE
SYNTAX SEQUENCE OF LlapEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The list of LLAP entries."
::= { llap 1 }
llapEntry OBJECT-TYPE
SYNTAX LlapEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An LLAP entry containing objects for the LocalTalk
Link Access Protocol for a particular LocalTalk
interface.
As an example, an instance of the llapOutPkts object
might be named llapOutPks.1"
INDEX { llapIfIndex }
::= { llapTable 1 }
LlapEntry ::= SEQUENCE {
llapIfIndex INTEGER,
llapInPkts Counter,
llapOutPkts Counter,
llapInNoHandlers Counter,
llapInLengthErrors Counter,
llapInErrors Counter,
llapCollisions Counter,
llapDefers Counter,
llapNoDataErrors Counter,
llapRandomCTSErrors Counter,
llapFCSErrors Counter
}
llapIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The LLAP interface to which this entry pertains.
The interface identified by a particular value of
this index is the same interface as identified
by the same value of ifIndex."
::= { llapEntry 1 }
Waldbusser & Frisa [Page 13]
RFC 1742 AppleTalk MIB II January 1995
-- this object has been deprecated because it duplicates the
-- sum of the MIB-II variables ifInUcastPkts and
-- ifInNUcastPkts
llapInPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS deprecated
DESCRIPTION
"The total number of good data packets received on
this LocalTalk interface."
::= { llapEntry 2 }
-- this object has been deprecated because it duplicates the
-- sum of the MIB-II variables ifOutUcastPkts and
-- ifOutNUcastPkts
llapOutPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS deprecated
DESCRIPTION
"The total number of data packets transmitted on
this LocalTalk interface."
::= { llapEntry 3 }
-- this object has been deprecated because it duplicates the
-- MIB-II variable ifInUnknownProtos
llapInNoHandlers OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS deprecated
DESCRIPTION
"The total number of good packets received on this
LocalTalk interface for which there was no protocol
handler."
::= { llapEntry 4 }
llapInLengthErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of packets received on this LocalTalk
interface whose actual length did not match the length
in the header."
::= { llapEntry 5 }
Waldbusser & Frisa [Page 14]
RFC 1742 AppleTalk MIB II January 1995
-- this object has been deprecated because it duplicates the
-- MIB-II variable ifInErrors
llapInErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS deprecated
DESCRIPTION
"The total number of packets containing errors received
on this LocalTalk interface."
::= { llapEntry 6 }
llapCollisions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of collisions assumed on this
LocalTalk interface due to the lack of a lapCTS reply."
::= { llapEntry 7 }
llapDefers OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of times this LocalTalk interface
deferred to other packets."
::= { llapEntry 8 }
llapNoDataErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of times this LocalTalk interface
received a lapRTS packet and expected a data packet,
but did not receive any data packet."
::= { llapEntry 9 }
llapRandomCTSErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of times this LocalTalk interface
received a lapCTS packet that was not solicited by a
lapRTS packet."
Waldbusser & Frisa [Page 15]
RFC 1742 AppleTalk MIB II January 1995
::= { llapEntry 10 }
llapFCSErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of times this LocalTalk interface
received a packet with an FCS (Frame Check Sequence)
error."
::= { llapEntry 11 }
-- The AARP Group
--
-- Implementation of this group is mandatory for all entities
-- that implement AARP
aarpTable OBJECT-TYPE
SYNTAX SEQUENCE OF AarpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The AppleTalk Address Translation Table contains an
equivalence of AppleTalk Network Addresses to the link
layer physical address."
::= { aarp 1 }
aarpEntry OBJECT-TYPE
SYNTAX AarpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Each entry contains one AppleTalk Network Address to
physical address equivalence.
As an example, an instance of the aarpPhysAddress
object might be named aarpPhysAddress.1.0.80.234"
INDEX { aarpIfIndex, aarpNetAddress }
::= { aarpTable 1 }
AarpEntry ::= SEQUENCE {
aarpIfIndex INTEGER,
aarpPhysAddress OCTET STRING,
aarpNetAddress DdpNodeAddress,
aarpStatus INTEGER
}
Waldbusser & Frisa [Page 16]
RFC 1742 AppleTalk MIB II January 1995
aarpIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The interface on which this entry's equivalence is
effective. The interface identified by a particular
value of this index is the same interface as
identified by the same value of ifIndex."
::= { aarpEntry 1 }
aarpPhysAddress OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The media-dependent physical address."
::= { aarpEntry 2 }
aarpNetAddress OBJECT-TYPE
SYNTAX DdpNodeAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The AppleTalk Network Address corresponding to the
media-dependent physical address."
::= { aarpEntry 3 }
aarpStatus OBJECT-TYPE
SYNTAX INTEGER {
valid(1),
invalid(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of this AARP entry.
Setting this object to the value invalid(2) has the
effect of invalidating the corresponding entry in the
aarpTable. That is, it effectively disassociates
the mapping identified with said entry. It is an
implementation-specific matter as to whether the agent
removes an invalidated entry from the table.
Accordingly, management stations must be prepared to
receive from agents tabular information corresponding
to entries not currently in use. Proper
interpretation of such entries requires examination
of the relevant aarpStatus object."
Waldbusser & Frisa [Page 17]
RFC 1742 AppleTalk MIB II January 1995
::= { aarpEntry 4 }
aarpLookups OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the AARP cache for this entity
was searched."
::= { aarp 2 }
aarpHits OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times an entry was searched for and
found in the AARP cache for this entity."
::= { aarp 3 }
-- The ATPort Group
--
-- Implementation of this group is mandatory for all entities
-- that implement AppleTalk ports
--
-- Note that to be compliant with this group, all variables
-- that have read-write access must be implemented as
-- read-write.
atportTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtportEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of AppleTalk ports for this entity."
::= { atport 1 }
atportEntry OBJECT-TYPE
SYNTAX AtportEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The description of one of the AppleTalk
ports on this entity.
As an example, an instance of the atportNetFrom object
might be named atportNetFrom.2"
Waldbusser & Frisa [Page 18]
RFC 1742 AppleTalk MIB II January 1995
INDEX { atportIndex }
::= { atportTable 1 }
AtportEntry ::= SEQUENCE {
atportIndex INTEGER,
atportDescr DisplayString,
atportType INTEGER,
atportNetStart ATNetworkNumber,
atportNetEnd ATNetworkNumber,
atportNetAddress DdpNodeAddress,
atportStatus INTEGER,
atportNetConfig INTEGER,
atportZoneConfig INTEGER,
atportZoneDefault ATName,
atportIfIndex INTEGER,
atportNetFrom DdpNodeAddress,
atportZoneFrom DdpNodeAddress,
atportInPkts Counter,
atportOutPkts Counter,
atportHome INTEGER,
atportCurrentZone ATName,
atportConflictPhysAddr OCTET STRING
}
atportIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for each AppleTalk port.
Its value is between 1 and the total number of
AppleTalk ports. The value for each port must
remain constant at least from the re-initialization
of the entity's network management system to the
next re-initialization."
::= { atportEntry 1 }
atportDescr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A text string containing information about the
port. This string is intended for presentation
to a human; it must not contain anything but printable
ASCII characters."
::= { atportEntry 2 }
Waldbusser & Frisa [Page 19]
RFC 1742 AppleTalk MIB II January 1995
-- Several objects throughout the MIB key off of atportType to
-- determine the format of OCTET STRING addresses of peers.
-- The address formats are as follows:
-- localtalk, ethertalk1, ethertalk2, tokentalk, iptalk,
-- fdditalk, smdstalk, arctalk, and virtual take the
-- format of DdpNodeAddress
-- serialPPP: null OCTET STRING
-- serialNonstandard: vendor specific
-- aurp: see AURP MIB to determine format
-- frameRelay: 32 bit DLCI in network byte order
-- (OCTET STRING (SIZE (4)))
-- x25: X121Address (see RFC 1382)
-- ip: IP address (OCTET STRING (SIZE (4)))
-- osi: NSAP (OCTET STRING (SIZE (3..20)))
-- decnetIV: 6 bit area, 10 bit host in network byte order
-- (OCTET STRING (SIZE (2)))
-- arap: ???
-- nonAppleTalk3Com: based on ifType
-- ipx: 32 bit network number in network byte order
-- followed by datalink address of host
-- arns: 32 bit ARNS header
-- hdlc: DdpNodeAddress or null OCTET STRING
atportType OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- none of the following
localtalk(2),
ethertalk1(3),
ethertalk2(4),
tokentalk(5),
iptalk(6),
serialPPP(7),
serialNonstandard(8),
virtual(9), -- an internal interface
fdditalk(10),
arctalk(11),
smdstalk(12),
aurp(13),
frameRelay(14),
x25(15),
ip(16),
osi(17),
decnetIV(18),
arap(19),
isdnInThePacketMode(20),
nonAppleTalk3Com(21),
ipx(22),
arns(23),
Waldbusser & Frisa [Page 20]
RFC 1742 AppleTalk MIB II January 1995
hdlc(24)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The type of port, distinguished by the protocol
immediately below DDP in the protocol stack."
::= { atportEntry 3 }
atportNetStart OBJECT-TYPE
SYNTAX ATNetworkNumber
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The first AppleTalk network address in the range
configured for this port. If this port is not a
native AppleTalk port, this object shall have the
value of two octets of zero."
::= { atportEntry 4 }
atportNetEnd OBJECT-TYPE
SYNTAX ATNetworkNumber
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The last AppleTalk network address in the range
configured for this port. If the network to which
this AppleTalk port is connected is a non-extended
network, or if it is not a native AppleTalk port,
the value for atportNetEnd shall be two octets of
zero."
::= { atportEntry 5 }
atportNetAddress OBJECT-TYPE
SYNTAX DdpNodeAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The AppleTalk network address configured for this
port. In addition, this value may be used as a hint
for an initial node number used during node-finding.
If this port is not a native AppleTalk port, this
object shall have the value of three octets of zero."
::= { atportEntry 6 }
atportStatus OBJECT-TYPE
SYNTAX INTEGER {
routing(1), --this port is fully configured & routing
Waldbusser & Frisa [Page 21]
RFC 1742 AppleTalk MIB II January 1995
unconfigured(2),
off(3),
invalid(4),
endNode(5), -- this port is acting as an end node
offDueToConflict(6), -- port is off due to
-- configuration conflict
other(7) -- none of the states defined above
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The configuration status of this port.
Setting this object to the value invalid(4) has the
effect of invalidating the corresponding entry in the
atportTable. That is, it effectively disassociates the
mapping identified with said entry. It is an
implementation-specific matter as to whether the agent
removes an invalidated entry from the table.
Accordingly, management stations must be prepared to
receive from agents tabular information corresponding
to entries not currently in use. Proper
interpretation of such entries requires examination
of the relevant atportStatus object."
::= { atportEntry 7 }
atportNetConfig OBJECT-TYPE
SYNTAX INTEGER {
conflictOrientedSeed(1), -- use configured network
-- range even if it conflicts with another
-- AppleTalk device
garnered(2), -- acquire from another AppleTalk device
guessed(3), -- generate a "random" network range
unconfigured(4), -- no other value applies
conflictAverseSeed(5), -- use configured network
-- range, but don't come up if it conflicts
softSeed(6) -- attempt to use configured network
-- range, but use network range from another
-- router if our configuration conflicts
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of the network information for this port.
If this port is not a native AppleTalk port, this
object shall have the value unconfigured(4)."
::= { atportEntry 8 }
Waldbusser & Frisa [Page 22]
RFC 1742 AppleTalk MIB II January 1995
atportZoneConfig OBJECT-TYPE
SYNTAX INTEGER {
conflictOrientedSeed(1), -- use configured zone
-- information even if it conflicts with
-- another AppleTalk device
garnered(2), -- acquire from another AppleTalk device
guessed(3), -- generate "random" zone information
unconfigured(4), -- no other value applies
conflictAverseSeed(5), -- use configured zone
-- information, but don't come up if it
-- conflicts
softSeed(6) -- attempt to use configured zone
-- information, but use zone information
-- from another router if our configuration
-- conflicts
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of the zone information for this port.
If this port is not a native AppleTalk port, this
object shall have the value unconfigured(4)."
::= { atportEntry 9 }
atportZoneDefault OBJECT-TYPE
SYNTAX ATName
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The name of the default zone for this port. If
this port only has one zone, that zone is
represented here. If this port is not a native
AppleTalk port, this object shall contain an octet
string of zero length.
When this value is changed in a router, the router
must send a zipNotify packet on the associated
network."
::= { atportEntry 10 }
atportIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The physical interface associated with this
AppleTalk port. The interface identified by a
particular value of this index is the same interface
Waldbusser & Frisa [Page 23]
RFC 1742 AppleTalk MIB II January 1995
as identified by the same value of ifIndex."
::= { atportEntry 11 }
atportNetFrom OBJECT-TYPE
SYNTAX DdpNodeAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"When atportNetConfig is set to garnered(2), this
variable contains the DDP address of an entity from
which the AppleTalk network number was garnered.
When atportNetConfig is set to
conflictOrientedSeed(1), conflictAverseSeed(5),
or softSeed(6), this variable contains the DDP
address of an entity which confirmed or supplied our
AppleTalk network number, for example by replying to
a ZIP GetNetInfo request.
If atportNetConfig is set to guessed(3) or
unconfigured(4), or if the entity has not received
any network number confirmation, this variable
should be set to three octets of zero."
::= { atportEntry 12 }
atportZoneFrom OBJECT-TYPE
SYNTAX DdpNodeAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"When atportZoneConfig is set to garnered(2), this
variable contains the DDP address of an entity from
which the AppleTalk zone list was garnered.
When atportZoneConfig is set to
conflictOrientedSeed(1), conflictAverseSeed(5), or
softSeed(6), this variable contains the DDP address
of an entity which confirmed or supplied our
AppleTalk zone information, for example by replying
to a ZIP GetNetInfo request or a ZIP Query.
If atportZoneConfig is set to guessed(3) or
unconfigured(4), or if the entity has not received
any zone confirmation, this variable should be set
to three octets of zero."
::= { atportEntry 13 }
Waldbusser & Frisa [Page 24]
RFC 1742 AppleTalk MIB II January 1995
atportInPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of packets received by this entity on
this port."
::= { atportEntry 14 }
atportOutPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of packets transmitted by this entity on
this port."
::= { atportEntry 15 }
atportHome OBJECT-TYPE
SYNTAX INTEGER {
home(1),
notHome(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An indication of whether or not the entity is
homed on this port, that is to say, a port on which
the entity could perform NBP registrations for
services that it chooses to advertise."
::= { atportEntry 16 }
atportCurrentZone OBJECT-TYPE
SYNTAX ATName
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The current zone for the port. In general, this is
the zone name in which services on this port will
be registered. If this port is not a native
AppleTalk port, this object shall contain an octet
string of zero length. Note that modifications to
this object do not affect the nbpTable."
::= { atportEntry 17 }
atportConflictPhysAddr OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
Waldbusser & Frisa [Page 25]
RFC 1742 AppleTalk MIB II January 1995
STATUS mandatory
DESCRIPTION
"The link-layer address of a device which caused
this entity to set atportStatus to
offDueToConflict(6). If this address is not
available, or if the entity has not set atportStatus
to offDueToConflict, this object shall be a zero
length OCTET STRING."
::= { atportEntry 18 }
-- The atportZoneTable stores information about the zones
-- associated with each port. The default zone for each
-- port is stored in the port's atportZoneDefault variable;
-- all other zones for the port are listed in this table.
-- If a port only has one zone, it should be stored in the
-- port's atportZoneDefault variable, and this table should
-- be empty.
--
-- One of the indexes for this table is atportZoneName.
-- Even though AppleTalk zone name matches are
-- case-insensitive, this table will store zone names
-- regardless of case. SNMP Get, GetNext and Set operations
-- are performed on these (potentially) mixed case strings
-- according to the normal SNMP rules with the following
-- caveat: in processing a SET request, the agent shall
-- perform a case-insensitive search and a case-sensitive
-- search. If the case-insensitive search matches and the
-- case-sensitive search does not match, the "equivalent"
-- zone name exists in another entry with a different
-- capitalization and the SET request shall fail due
-- to the name being inconsistent (SNMPv1 should return a
-- genErr.) This insures that only one version of a zone
-- name will appear in each agent, at the expense of forcing
-- a management station to query using that exact name.
atportZoneTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtportZoneEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The table of zone information for non-default
zones on ports."
::= { atport 2 }
atportZoneEntry OBJECT-TYPE
SYNTAX AtportZoneEntry
ACCESS not-accessible
STATUS mandatory
Waldbusser & Frisa [Page 26]
RFC 1742 AppleTalk MIB II January 1995
DESCRIPTION
"An entry of zone information for a port.
As an example, an instance of the atportZoneStatus
object might be named
atportZoneStatus.2.8.84.119.105.108.105.103.104.116"
INDEX { atportZonePort, atportZoneName }
::= { atportZoneTable 1 }
AtportZoneEntry ::= SEQUENCE {
atportZonePort INTEGER,
atportZoneName ATName (SIZE (1..32)),
atportZoneStatus INTEGER
}
atportZonePort OBJECT-TYPE
SYNTAX INTEGER
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An integer representing the port to which this zone
belongs. The port identified by a particular value
of this object is the same port as identified by the
same value of atportIndex."
::= { atportZoneEntry 1 }
atportZoneName OBJECT-TYPE
SYNTAX ATName (SIZE (1..32))
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A zone name configured for the AppleTalk port
referred to in the corresponding entry of
atportZonePort.
When this value is changed in a router, the router
must send a zipNotify packet on the associated
network."
::= { atportZoneEntry 2 }
atportZoneStatus OBJECT-TYPE
SYNTAX INTEGER {
valid(1),
invalid(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
Waldbusser & Frisa [Page 27]
RFC 1742 AppleTalk MIB II January 1995
"The status of this zone entry.
Setting this object to the value invalid(2) has the
effect of invalidating the corresponding entry in
the atportZoneTable. That is, it effectively
disassociates the mapping identified with said
entry. It is an implementation-specific matter as
to whether the agent removes an invalidated entry
from the table. Accordingly, management stations
must be prepared to receive from agents tabular
information corresponding to entries not currently
in use. Proper interpretation of such entries
requires examination of the relevant
atportZoneStatus object."
::= { atportZoneEntry 3 }
-- The DDP Group
--
-- Implementation of this group is mandatory for all
-- entities that implement DDP
--
-- This group consists of DDP variables that would be
-- implemented by either a router or an end node. The
-- following variables are included:
-- ddpOutRequests
-- ddpOutShorts
-- ddpOutLongs
-- ddpInReceives
-- ddpInLocalDatagrams
-- ddpNoProtocolHandlers
-- ddpTooShortErrors
-- ddpTooLongErrors
-- ddpShortDDPErrors
-- ddpChecksumErrors
-- ddpListenerTable
--
-- Note that the variables in this group are not numbered
-- sequentially. This was done so that it was not necessary
-- to deprecate variables from RFC 1243.
ddpOutRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of DDP datagrams which were
supplied to DDP by local DDP clients in requests for
Waldbusser & Frisa [Page 28]
RFC 1742 AppleTalk MIB II January 1995
transmission. Note that this counter does not
include any datagrams counted in ddpForwRequests."
::= { ddp 1 }
ddpOutShorts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of short DDP datagrams which were
transmitted from this entity."
::= { ddp 2 }
ddpOutLongs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of long DDP datagrams which were
transmitted from this entity."
::= { ddp 3 }
ddpInReceives OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input datagrams received by
DDP, including those received in error."
::= { ddp 4 }
ddpInLocalDatagrams OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams for which
this
entity was their final DDP destination."
::= { ddp 6 }
ddpNoProtocolHandlers OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of DDP datagrams addressed to this
entity that were addressed to an upper layer protocol
Waldbusser & Frisa [Page 29]
RFC 1742 AppleTalk MIB II January 1995
for which no protocol handler existed."
::= { ddp 7 }
ddpTooShortErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams dropped
because the received data length was less than the
data length specified in the DDP header or the
received data length was less than the length of the
expected DDP header."
::= { ddp 9 }
ddpTooLongErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams dropped
because they exceeded the maximum DDP datagram
size."
::= { ddp 10 }
ddpShortDDPErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams dropped
because this entity was not their final destination
and their type was short DDP."
::= { ddp 12 }
ddpChecksumErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams for which
this DDP entity was their final destination, and
which were dropped because of a checksum error."
::= { ddp 14 }
ddpListenerTable OBJECT-TYPE
SYNTAX SEQUENCE OF DdpListenerEntry
ACCESS not-accessible
Waldbusser & Frisa [Page 30]
RFC 1742 AppleTalk MIB II January 1995
STATUS mandatory
DESCRIPTION
"The ddpListenerTable stores information for each
DDP socket that has a listener."
::= { ddp 15 }
ddpListenerEntry OBJECT-TYPE
SYNTAX DdpListenerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This ddpListenerEntry contains information about a
particular socket that has a socket listener.
As an example, an instance of the ddpListenerStatus
object might be named ddpListenerStatus.0.80.220.1"
INDEX { ddpListenerAddress }
::= { ddpListenerTable 1 }
DdpListenerEntry ::= SEQUENCE {
ddpListenerAddress DdpSocketAddress,
ddpListenerInPkts Counter,
ddpListenerStatus INTEGER
}
ddpListenerAddress OBJECT-TYPE
SYNTAX DdpSocketAddress
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The DDP address that this socket listener is bound
to. If this socket listener isn't bound to a
particular address, for instance if it is intended
for all interfaces, this object shall have the value
of three octets of zero followed by one octet of
socket number. The socket number must not equal
zero."
::= { ddpListenerEntry 1 }
ddpListenerInPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of packets received for this listener."
::= { ddpListenerEntry 2 }
Waldbusser & Frisa [Page 31]
RFC 1742 AppleTalk MIB II January 1995
ddpListenerStatus OBJECT-TYPE
SYNTAX INTEGER {
valid(1),
invalid(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of this socket listener.
Setting this object to the value invalid(2) has the
effect of invalidating the corresponding entry in the
ddpListenerTable. That is, it effectively
disassociates the mapping identified with said
entry. It is an implementation-specific matter as
to whether the agent removes an invalidated entry
from the table. Accordingly, management stations
must be prepared to receive from agents tabular
information corresponding to entries not currently
in use. Proper interpretation of such entries
requires examination of the relevant
ddpListenerStatus object."
::= { ddpListenerEntry 3 }
-- The DDP Router Group
--
-- Implementation of this group is required for all routers
-- which implement DDP
--
-- This group consists of DDP variables that only a router
-- would implement. The following variables are included:
-- ddpForwRequests
-- ddpOutNoRoutes
-- ddpBroadcastErrors
-- ddpHopCountErrors
-- ddpForwardingTable
--
-- Note that the variables in this group are not numbered
-- sequentially. This was done so that variables from
-- RFC 1243 did not need to be deprecated.
ddpForwRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of input datagrams for which this entity
was not their final DDP destination, as a result of
Waldbusser & Frisa [Page 32]
RFC 1742 AppleTalk MIB II January 1995
which an attempt was made to find a route to forward
them to that final destination."
::= { ddp 5 }
ddpOutNoRoutes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of DDP datagrams dropped because a
route could not be found to their final destination."
::= { ddp 8 }
ddpBroadcastErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams dropped
because this entity was not their final destination
and they were addressed to the link level broadcast."
::= { ddp 11 }
ddpHopCountErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams dropped
because this entity was not their final destination
and their hop count would exceed 15."
::= { ddp 13 }
-- The ddpForwardingTable is a read-only table which shows the
-- next hop that a datagram will take when being routed to a
-- specific network. If a manager wishes to change data in
-- this table via SNMP, he must change it in the MIB for the
-- routing protocol itself (by incrementing hop counts,
-- etc), rather than in this table. This table is derived
-- by the managed entity from the information it receives
-- from the routing protocols that it supports.
--
-- This table also shows the routing table from which the next
-- hop was derived. When a MIB is written for an AppleTalk
-- routing protocol, it should include the definition of an
-- object identifier which will be used in the
-- ddpForwardingProto variable defined here. (For example,
-- a value for RTMP is defined as { ddp-forw-proto-oids 1 }
Waldbusser & Frisa [Page 33]
RFC 1742 AppleTalk MIB II January 1995
-- below.)
--
-- To look for a specific net N in this table, it is suggested
-- that the management station perform a get-next query for
-- ddpForwardingNetEnd.(N-1). This will retrieve the correct
-- row if it exists in the table.
ddpForwardingTable OBJECT-TYPE
SYNTAX SEQUENCE OF DdpForwardingEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of forwarding entries for DDP. This table
contains a route for each AppleTalk network currently
known to the entity."
::= { ddp 16 }
ddpForwardingEntry OBJECT-TYPE
SYNTAX DdpForwardingEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A forwarding entry for a particular AppleTalk
network.
As an example, an instance of the ddpForwardingPort
object might be named ddpForwardingPort.0.90"
INDEX { ddpForwardingNetEnd }
::= { ddpForwardingTable 1 }
DdpForwardingEntry ::= SEQUENCE {
ddpForwardingNetEnd ATNetworkNumber,
ddpForwardingNetStart ATNetworkNumber,
ddpForwardingNextHop OCTET STRING,
ddpForwardingProto OBJECT IDENTIFIER,
ddpForwardingModifiedTime TimeTicks,
ddpForwardingUseCounts Counter,
ddpForwardingPort INTEGER
}
ddpForwardingNetEnd OBJECT-TYPE
SYNTAX ATNetworkNumber
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The last network number in the network range
matched by this forwarding entry. This will not be
zero even if this corresponds to a non-extended
Waldbusser & Frisa [Page 34]
RFC 1742 AppleTalk MIB II January 1995
net."
::= { ddpForwardingEntry 1 }
ddpForwardingNetStart OBJECT-TYPE
SYNTAX ATNetworkNumber
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The first network number in the network range
matched by this forwarding entry."
::= { ddpForwardingEntry 2 }
ddpForwardingNextHop OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The next hop in the route to this entry's
destination network. The format of this address can
be determined by examinating the atportType
corresponding to this entry."
::= { ddpForwardingEntry 3 }
ddpForwardingProto OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The routing mechanism by which this route was
learned."
::= { ddpForwardingEntry 4 }
ddpForwardingModifiedTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of sysUpTime at the time of the last
modification to this entry. The initial value of
ddpForwardingModified time shall be the value of
sysUpTime at the time the entry is created."
::= { ddpForwardingEntry 5 }
ddpForwardingUseCounts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
Waldbusser & Frisa [Page 35]
RFC 1742 AppleTalk MIB II January 1995
"The number of times this entry has been used to
route a packet to the destination network. Note
that this counter is not cleared when the
corresponding ddpForwardingNextHop variable
changes."
::= { ddpForwardingEntry 6 }
ddpForwardingPort OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The AppleTalk port through which
ddpForwardingNextHop is reached. The interface
identified by a particular value of this variable is
the same interface as identified by the same value
of atportIndex."
::= { ddpForwardingEntry 7 }
ddpForwProtoOids OBJECT IDENTIFIER ::= { ddp 17 }
-- The value to be assigned to ddpForwardingProto when the
-- routing protocol is RTMP.
rtmpRoutingProto OBJECT IDENTIFIER ::= { ddpForwProtoOids 1 }
-- The value to be assigned to ddpForwardingProto when the
-- routing protocol is KIP.
kipRoutingProto OBJECT IDENTIFIER ::= { ddpForwProtoOids 2 }
ddpForwardingTableOverflows OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the entity attempted to add an
entry to the forwarding table but failed due to
overflow."
::= { ddp 18 }
-- The RTMP Group
--
-- Implementation of this group is required for all routers
-- which implement RTMP
rtmpTable OBJECT-TYPE
SYNTAX SEQUENCE OF RtmpEntry
Waldbusser & Frisa [Page 36]
RFC 1742 AppleTalk MIB II January 1995
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of Routing Table Maintenance Protocol
entries for this entity."
::= { rtmp 1 }
rtmpEntry OBJECT-TYPE
SYNTAX RtmpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The route entry to a particular network range.
As an example, an instance of the rtmpPort object
might be named rtmpPort.0.80"
INDEX { rtmpRangeStart }
::= { rtmpTable 1 }
RtmpEntry ::= SEQUENCE {
rtmpRangeStart ATNetworkNumber,
rtmpRangeEnd ATNetworkNumber,
rtmpNextHop OCTET STRING,
rtmpType INTEGER,
rtmpPort INTEGER,
rtmpHops INTEGER,
rtmpState INTEGER
}
rtmpRangeStart OBJECT-TYPE
SYNTAX ATNetworkNumber
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The first DDP network address in the network range
to which this routing entry pertains. This is a two
octet DDP network address in network byte order."
::= { rtmpEntry 1 }
rtmpRangeEnd OBJECT-TYPE
SYNTAX ATNetworkNumber
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The last DDP network address in the network range
to which this routing entry pertains. This is a two
octet DDP network address in network byte order. If
the network to which this routing entry pertains is
Waldbusser & Frisa [Page 37]
RFC 1742 AppleTalk MIB II January 1995
a non-extended network, the value for rtmpRangeEnd
shall be two octets of zero."
::= { rtmpEntry 2 }
rtmpNextHop OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The next internet router in the route to this
entry's destination network. The format of this
address can be determined by examinating the
atportType corresponding to this entry."
::= { rtmpEntry 3 }
rtmpType OBJECT-TYPE
SYNTAX INTEGER {
other(1),
appletalk(2),
serialPPP(3),
serialNonstandard(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of network over which this route points."
::= { rtmpEntry 4 }
rtmpPort OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The AppleTalk port over which this route points.
The interface identified by a particular value of
this variable is the same interface as identified by
the same value of atportIndex."
::= { rtmpEntry 5 }
rtmpHops OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of hops required to reach the
destination network to which this routing entry
pertains."
::= { rtmpEntry 6 }
Waldbusser & Frisa [Page 38]
RFC 1742 AppleTalk MIB II January 1995
rtmpState OBJECT-TYPE
SYNTAX INTEGER {
good(1),
suspect(2),
badZero(3),
badOne(4),
invalid(5)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of the information contained in this
route entry.
Setting this object to the value invalid(5) has the
effect of invalidating the corresponding entry in
the rtmpTable. That is, it effectively
disassociates the mapping identified with said
entry. It is an implementation-specific matter as
to whether the agent removes an invalidated entry
from the table. Accordingly, management stations
must be prepared to receive from agents tabular
information corresponding to entries not currently
in use. Proper interpretation of such entries
requires examination of the relevant rtmpState
object."
::= { rtmpEntry 7 }
rtmpInDataPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of good RTMP data packets
received by this entity."
::= { rtmp 2 }
rtmpOutDataPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of RTMP packets sent by this
entity."
::= { rtmp 3 }
rtmpInRequestPkts OBJECT-TYPE
SYNTAX Counter
Waldbusser & Frisa [Page 39]
RFC 1742 AppleTalk MIB II January 1995
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of good RTMP Request packets
received by this entity."
::= { rtmp 4 }
rtmpNextIREqualChanges OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of times RTMP changes the
Next Internet Router in a routing entry because the
hop count advertised in a routing tuple was equal to
the current hop count for a particular network."
::= { rtmp 5 }
rtmpNextIRLessChanges OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of times RTMP changes the
Next Internet Router in a routing entry because the
hop count advertised in a routing tuple was less
than the current hop count for a particular network."
::= { rtmp 6 }
rtmpRouteDeletes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of times RTMP deletes a route
because it was aged out of the table. This can help
to detect routing problems."
::= { rtmp 7 }
rtmpRoutingTableOverflows OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times RTMP attempted to add a route
to the RTMP table but failed due to lack of space."
::= { rtmp 8 }
Waldbusser & Frisa [Page 40]
RFC 1742 AppleTalk MIB II January 1995
-- The RTMP Stub Group
--
-- Implementation of this group is mandatory for all
-- entities that implement RTMP
--
-- It is intended that this group be implemented by routers
-- and end nodes.
rtmpOutRequestPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of RTMP Request packets sent
by this entity."
::= { rtmpStub 1 }
rtmpInVersionMismatches OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of RTMP packets received by
this entity that were rejected due to a version
mismatch."
::= { rtmpStub 2 }
rtmpInErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of RTMP packets received by
this entity that were rejected for an error other
than version mismatch."
::= { rtmpStub 3 }
-- The KIP Group
--
-- Implementation of this group is mandatory for all
-- entities that implement KIP
kipTable OBJECT-TYPE
SYNTAX SEQUENCE OF KipEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
Waldbusser & Frisa [Page 41]
RFC 1742 AppleTalk MIB II January 1995
"The table of routing information for KIP networks."
::= { kip 1 }
kipEntry OBJECT-TYPE
SYNTAX KipEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the routing table for KIP networks.
As an example, an instance of the kipCore object
might be named kipCore.0.80"
INDEX { kipNetStart }
::= { kipTable 1 }
KipEntry ::= SEQUENCE {
kipNetStart ATNetworkNumber,
kipNetEnd ATNetworkNumber,
kipNextHop IpAddress,
kipHopCount INTEGER,
kipBCastAddr IpAddress,
kipCore INTEGER,
kipType INTEGER,
kipState INTEGER,
kipShare INTEGER,
kipFrom IpAddress
}
kipNetStart OBJECT-TYPE
SYNTAX ATNetworkNumber
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The first AppleTalk network address in the range
for this routing entry. This address is a two octet
DDP network address in network byte order."
::= { kipEntry 1 }
kipNetEnd OBJECT-TYPE
SYNTAX ATNetworkNumber
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The last AppleTalk network address in the range for
this routing entry. This address is a two octet DDP
network address in network byte order. If the
network to which this AppleTalk port is connected is
a non-extended network, the value for kipNetEnd
Waldbusser & Frisa [Page 42]
RFC 1742 AppleTalk MIB II January 1995
shall be two octets of zero."
::= { kipEntry 2 }
kipNextHop OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The IP address of the next hop in the route to this
entry's destination network."
::= { kipEntry 3 }
kipHopCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The number of hops required to reach the destination
network to which this entry pertains."
::= { kipEntry 4 }
kipBCastAddr OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The form of the IP address used to broadcast on this
network."
::= { kipEntry 5 }
kipCore OBJECT-TYPE
SYNTAX INTEGER {
core(1),
notcore(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of kipNextHop as a core gateway."
::= { kipEntry 6 }
kipType OBJECT-TYPE
SYNTAX INTEGER {
kipRouter(1),
net(2),
host(3),
other(4),
async(5)
Waldbusser & Frisa [Page 43]
RFC 1742 AppleTalk MIB II January 1995
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The type of the entity that this route points to."
::= { kipEntry 7 }
kipState OBJECT-TYPE
SYNTAX INTEGER {
configured(1), -- this entry is not aged
learned(2),
invalid(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The state of this network entry.
Setting this object to the value invalid(3) has the
effect of invalidating the corresponding entry in the
kipTable. That is, it effectively disassociates the
mapping identified with said entry. It is an
implementation-specific matter as to whether the agent
removes an invalidated entry from the table.
Accordingly, management stations must be prepared to
receive from agents tabular information corresponding
to entries not currently in use. Proper
interpretation of such entries requires examination
of the relevant kipState object."
::= { kipEntry 8 }
kipShare OBJECT-TYPE
SYNTAX INTEGER {
shared(1),
private(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"If the information in this entry is propagated to
other routers as part of the AA routing protocol,
the value of this variable is equal to shared(1).
Otherwise its value is private(2)."
::= { kipEntry 9 }
kipFrom OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-only
Waldbusser & Frisa [Page 44]
RFC 1742 AppleTalk MIB II January 1995
STATUS mandatory
DESCRIPTION
"The IP address from which the routing entry was
learned via the AA protocol. If this entry was not
created via the AA protocol, it should contain IP
address 0.0.0.0."
::= { kipEntry 10 }
-- The ZIP Router Group
--
-- Implementation of this group is required for all routers
-- which implement ZIP
--
-- This group consists of ZIP variables that would be
-- implemented by a router.
zipTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZipEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The table of zone information for reachable
AppleTalk networks."
::= { zipRouter 1 }
zipEntry OBJECT-TYPE
SYNTAX ZipEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry of zone information for a particular zone
and network combination.
As an example, an instance of the zipZoneState object
might be named zipZoneState.0.80.4"
INDEX { zipZoneNetStart, zipZoneIndex }
::= { zipTable 1 }
ZipEntry ::= SEQUENCE {
zipZoneName ATName,
zipZoneIndex INTEGER,
zipZoneNetStart ATNetworkNumber,
zipZoneNetEnd ATNetworkNumber,
zipZoneState INTEGER,
zipZoneFrom OCTET STRING,
zipZonePort INTEGER
}
Waldbusser & Frisa [Page 45]
RFC 1742 AppleTalk MIB II January 1995
zipZoneName OBJECT-TYPE
SYNTAX ATName
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The zone name of this entry. This is stored in
Mac ASCII format. If the full zone list for the
entry is not known, the value for zipZoneName shall
be a zero length octet string."
::= { zipEntry 1 }
zipZoneIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An integer that is unique to the zipZoneName that
is present in this entry. For any given zone name,
every zipEntry that has an equal zone name will have
the same zipZoneIndex. When a zone name is
discovered which is not currently in the table, it
will be assigned an index greater than any
previously assigned index."
::= { zipEntry 2 }
zipZoneNetStart OBJECT-TYPE
SYNTAX ATNetworkNumber
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The network that starts the range for this entry.
This address is a two octet DDP network address in
network byte order."
::= { zipEntry 3 }
zipZoneNetEnd OBJECT-TYPE
SYNTAX ATNetworkNumber
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The network that ends the range for this entry.
This address is a two octet DDP network address in
network byte order. If the network to which this
zip entry pertains is a non-extended network, the
value for zipZoneNetEnd shall be two octets of
zero."
::= { zipEntry 4 }
Waldbusser & Frisa [Page 46]
RFC 1742 AppleTalk MIB II January 1995
zipZoneState OBJECT-TYPE
SYNTAX INTEGER {
valid(1),
invalid(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The state of this zip entry.
Setting this object to the value invalid(2) has the
effect of invalidating the corresponding entry in
the zipTable. That is, it effectively
disassociates the mapping identified with said
entry. It is an implementation-specific matter as
to whether the agent removes an invalidated entry
from the table. Accordingly, management stations
must be prepared to receive from agents tabular
information corresponding to entries not currently
in use. Proper interpretation of such entries
requires examination of the relevant zipZoneState
object."
::= { zipEntry 5 }
zipZoneFrom OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The address from which this zone name to network
number mapping was learned. The format of this
address can be determined by examining the
atportType corresponding to this entry. When this
mapping is learned from the entity itself, this
object shall have the value of three
octets of zero."
::= { zipEntry 6 }
zipZonePort OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The AppleTalk port through which this zone name to
network number mapping was learned. The interface
identified by a particular value of this variable is
the same interface as identified by the same value
of atportIndex."
Waldbusser & Frisa [Page 47]
RFC 1742 AppleTalk MIB II January 1995
::= { zipEntry 7 }
zipInZipQueries OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP Queries received by this entity."
::= { zipRouter 2 }
zipInZipReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP Replies received by this entity."
::= { zipRouter 3 }
zipInZipExtendedReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP Extended Replies received by this
entity."
::= { zipRouter 4 }
zipZoneConflictErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times a conflict has been detected
between this entity's zone information and another
entity's zone information."
::= { zipRouter 5 }
zipInObsoletes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP Takedown or ZIP Bringup packets
received by this entity. Note that as the ZIP
Takedown and ZIP Bringup packets have been
obsoleted, the receipt of one of these packets
indicates that a node sent it in error."
::= { zipRouter 6 }
Waldbusser & Frisa [Page 48]
RFC 1742 AppleTalk MIB II January 1995
-- The zipRouterNetInfoTable is used to record information
-- about zipGetNetInfo and zipGetNetInfo Reply packets that
-- were received on each port for a router. This table
-- augments the atportTable.
zipRouterNetInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZipRouterNetInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The table of Net Info packets received by each port
on this entity."
::= { zipRouter 7 }
zipRouterNetInfoEntry OBJECT-TYPE
SYNTAX ZipRouterNetInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The description of the Net Info packets received on
a particular port on this entity. One such entry
shall exist for each atport on this router entity.
As an example, an instance of the zipInGetNetInfos
object might be named zipInGetNetInfos.2"
INDEX { atportIndex }
::= { zipRouterNetInfoTable 1 }
ZipRouterNetInfoEntry ::= SEQUENCE {
zipInGetNetInfos Counter,
zipOutGetNetInfoReplies Counter,
zipZoneOutInvalids Counter,
zipAddressInvalids Counter
}
zipInGetNetInfos OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP GetNetInfo packets received on
this port by this entity."
::= { zipRouterNetInfoEntry 1 }
zipOutGetNetInfoReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
Waldbusser & Frisa [Page 49]
RFC 1742 AppleTalk MIB II January 1995
DESCRIPTION
"The number of ZIP GetNetInfo Reply packets sent out
this port by this entity."
::= { zipRouterNetInfoEntry 2 }
zipZoneOutInvalids OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times this entity has sent a ZIP
GetNetInfo Reply with the zone invalid bit set in
response to a GetNetInfo Request with an invalid
zone name."
::= { zipRouterNetInfoEntry 3 }
zipAddressInvalids OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times this entity had to broadcast a
ZIP GetNetInfo Reply because the GetNetInfo Request
had an invalid address."
::= { zipRouterNetInfoEntry 4 }
-- The ZIP End Node Group
--
-- Implementation of this group is mandatory for all entities
-- that implement ZIP
--
-- This group consists of ZIP variables that would be
-- implemented by either a router or an end node.
-- The zipNetInfoTable is used to record information about
-- zipGetNetInfo and zipGetNetInfo Reply packets that were
-- received on each port of an entity. This table augments
-- the atportTable.
zipNetInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZipNetInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The table of Net Info packets received by each port
on this entity."
::= { zipEndNode 1 }
Waldbusser & Frisa [Page 50]
RFC 1742 AppleTalk MIB II January 1995
zipNetInfoEntry OBJECT-TYPE
SYNTAX ZipNetInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The description of the Net Info packets received on
a particular port on this entity. One such entry
shall exist for each atport on this entity.
As an example, an instance of the zipOutGetNetInfos
object might be named zipOutGetNetInfos.2"
INDEX { atportIndex }
::= { zipNetInfoTable 1 }
ZipNetInfoEntry ::= SEQUENCE {
zipOutGetNetInfos Counter,
zipInGetNetInfoReplies Counter,
zipZoneInInvalids Counter
}
zipOutGetNetInfos OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP GetNetInfo packets sent out this
port by this entity."
::= { zipNetInfoEntry 1 }
zipInGetNetInfoReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP GetNetInfo Reply packets received
on this port by this entity."
::= { zipNetInfoEntry 2 }
zipZoneInInvalids OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times this entity has received a ZIP
GetNetInfo Reply with the zone invalid bit set
because the corresponding GetNetInfo Request had an
invalid zone name."
::= { zipNetInfoEntry 3 }
Waldbusser & Frisa [Page 51]
RFC 1742 AppleTalk MIB II January 1995
zipInErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP packets received by this entity
that were rejected for any error."
::= { zipEndNode 2 }
-- The NBP Group
--
-- Implementation of this group is mandatory for all entities
-- that implement NBP
nbpTable OBJECT-TYPE
SYNTAX SEQUENCE OF NbpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The table of NBP services registered on this entity."
::= { nbp 1 }
nbpEntry OBJECT-TYPE
SYNTAX NbpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The description of an NBP service registered on this
entity.
As an example, an instance of the nbpZone object
might be named nbpZone.2"
INDEX { nbpIndex }
::= { nbpTable 1 }
NbpEntry ::= SEQUENCE {
nbpIndex INTEGER,
nbpObject ATName (SIZE (1..32)),
nbpType ATName (SIZE (1..32)),
nbpZone ATName,
nbpState INTEGER,
nbpAddress DdpSocketAddress,
nbpEnumerator INTEGER (0..255)
}
nbpIndex OBJECT-TYPE
SYNTAX INTEGER
Waldbusser & Frisa [Page 52]
RFC 1742 AppleTalk MIB II January 1995
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The index of this NBP entry. This index is unique
with respect to the indexes of all other NBP entries,
and shall remain constant throughout the lifetime
of this object."
::= { nbpEntry 1 }
nbpObject OBJECT-TYPE
SYNTAX ATName (SIZE (1..32))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The name of the service described by this entity.
When this variable is changed, the entity should
perform an NBP registration using the new nbpObject."
::= { nbpEntry 2 }
nbpType OBJECT-TYPE
SYNTAX ATName (SIZE (1..32))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The type of the service described by this entity.
When this variable is changed, the entity should
perform an NBP registration using the new nbpType."
::= { nbpEntry 3 }
nbpZone OBJECT-TYPE
SYNTAX ATName
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The zone the service described by this entity is
registered in. This must be the actual zone name,
without any wildcard characters. When this variable
is changed, the entity should perform an NBP
registration using the new nbpZone."
::= { nbpEntry 4 }
nbpState OBJECT-TYPE
SYNTAX INTEGER {
valid(1),
registering(2), -- attempting to register the service
registrationFailed(3),
invalid(4)
}
Waldbusser & Frisa [Page 53]
RFC 1742 AppleTalk MIB II January 1995
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The state of this NBP entry.
When the registration for an entry in the nbpTable
fails, it is an implementation-specific matter as to
how long the entry will remain in the
registrationFailed(3) state before moving to the
invalid(4) state. Note that the entry may pass
immediately from the registrationFailed state to
the invalid state.
Setting this object to the value invalid(4) has the
effect of invalidating the corresponding entry in the
nbpTable. That is, it effectively disassociates the
mapping identified with said entry. It is an
implementation-specific matter as to whether the agent
removes an invalidated entry from the table.
Accordingly, management stations must be prepared to
receive from agents tabular information corresponding
to entries not currently in use. Proper
interpretation of such entries requires examination
of the relevant nbpState object."
::= { nbpEntry 5 }
nbpAddress OBJECT-TYPE
SYNTAX DdpSocketAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The DDP network, node, and socket number of this
entity. If this is unspecified, for instance if the
registration is on all ports of a multiport device,
this object shall have the value of three octets of
zero, followed by one octet of socket number."
::= { nbpEntry 6 }
nbpEnumerator OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The enumerator assigned to this entity."
::= { nbpEntry 7 }
nbpInLookUpRequests OBJECT-TYPE
SYNTAX Counter
Waldbusser & Frisa [Page 54]
RFC 1742 AppleTalk MIB II January 1995
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP LookUp Requests received."
::= { nbp 2 }
nbpInLookUpReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP LookUp Replies received."
::= { nbp 3 }
nbpInBroadcastRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP Broadcast Requests received."
::= { nbp 4 }
nbpInForwardRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP Forward Requests received."
::= { nbp 5 }
nbpOutLookUpReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP LookUp Replies sent."
::= { nbp 6 }
nbpRegistrationFailures OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times this node experienced a failure
in attempting to register an NBP entity."
::= { nbp 7 }
Waldbusser & Frisa [Page 55]
RFC 1742 AppleTalk MIB II January 1995
nbpInErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP packets received by this entity
that were rejected for any error."
::= { nbp 8 }
-- The ATEcho Group
--
-- Implementation of this group is mandatory for all
-- entities that implement ATEcho
atechoRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of AppleTalk Echo requests received."
::= { atecho 1 }
atechoReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of AppleTalk Echo replies sent."
::= { atecho 2 }
atechoOutRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The count of AppleTalk Echo requests sent."
::= { atecho 3 }
atechoInReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The count of AppleTalk Echo replies received."
::= { atecho 4 }
Waldbusser & Frisa [Page 56]
RFC 1742 AppleTalk MIB II January 1995
-- The ATP Group
--
-- Implementation of this group is mandatory for all entities
-- that implement ATP
atpInPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATP packets received by this entity."
::= { atp 1 }
atpOutPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATP packets sent by this entity."
::= { atp 2 }
atpTRequestRetransmissions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times that a timeout occurred and a
Transaction Request packet needed to be
retransmitted by this host."
::= { atp 3 }
atpTResponseRetransmissions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times a timeout was detected and a
Transaction Response packet needed to be
retransmitted by this host."
::= { atp 4 }
atpReleaseTimerExpiredCounts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the release timer expired, as a
result of which a Request Control Block had to be
Waldbusser & Frisa [Page 57]
RFC 1742 AppleTalk MIB II January 1995
deleted."
::= { atp 5 }
atpRetryCountExceededs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the retry count was exceeded,
and an error was returned to the client of ATP."
::= { atp 6 }
atpListenerTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtpListenerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The atpListenerTable stores information for each ATP
socket that has a listener."
::= { atp 7 }
atpListenerEntry OBJECT-TYPE
SYNTAX AtpListenerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This atpListenerEntry contains information about a
particular socket that has a socket listener.
As an example, an instance of the atpListenerStatus
object might be named atpListenerStatus.0.80.220.3"
INDEX { atpListenerAddress }
::= { atpListenerTable 1 }
AtpListenerEntry ::= SEQUENCE {
atpListenerAddress DdpSocketAddress,
atpListenerStatus INTEGER
}
atpListenerAddress OBJECT-TYPE
SYNTAX DdpSocketAddress
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The DDP address that this socket listener is bound
to. If this socket listener isn't bound to a
particular address, for instance if it is intended
for all interfaces, this object shall have the value
Waldbusser & Frisa [Page 58]
RFC 1742 AppleTalk MIB II January 1995
of three octets of zero followed by one octet of
socket number."
::= { atpListenerEntry 1 }
atpListenerStatus OBJECT-TYPE
SYNTAX INTEGER {
valid(1),
invalid(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of this socket.
Setting this object to the value invalid(2) has the
effect of invalidating the corresponding entry in
the atpListenerTable. That is, it effectively
disassociates the mapping identified with said
entry. It is an implementation-specific matter as
to whether the agent removes an invalidated entry
from the table. Accordingly, management stations
must be prepared to receive from agents tabular
information corresponding to entries not currently
in use. Proper interpretation of such entries
requires examination of the relevant
atpListenerStatus object."
::= { atpListenerEntry 2 }
-- The PAP group
--
-- Implementation of this group is mandatory for all entities
-- that implement PAP
papInOpenConns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PAP Open Connection requests received
by this entity."
::= { pap 1 }
papOutOpenConns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
Waldbusser & Frisa [Page 59]
RFC 1742 AppleTalk MIB II January 1995
"The number of PAP Open Connection requests sent by
this entity."
::= { pap 2 }
papInDatas OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PAP Data messages received by
this entity."
::= { pap 3 }
papOutDatas OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PAP Data messages sent by
this entity."
::= { pap 4 }
papInCloseConns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PAP Close Connection requests
received by this entity."
::= { pap 5 }
papOutCloseConns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PAP Close Connection requests sent by
this entity."
::= { pap 6 }
papTickleTimeoutCloses OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the PAP entity on this node
closed a connection because it didn't receive a
Tickle message before its timer expired."
Waldbusser & Frisa [Page 60]
RFC 1742 AppleTalk MIB II January 1995
::= { pap 7 }
papServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF PapServerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of servers on this entity that are
accessible through the Printer Access Protocol."
::= { pap 8 }
papServerEntry OBJECT-TYPE
SYNTAX PapServerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A set of information about a particular PAP server's
configuration and performance.
As an example, an instance of the papServerStatus
object might be named papServerStatus.1"
INDEX { papServerIndex }
::= { papServerTable 1 }
PapServerEntry ::= SEQUENCE {
papServerIndex INTEGER,
papServerListeningSocket DdpSocketAddress,
papServerStatus DisplayString,
papServerCompletedJobs Counter,
papServerBusyJobs INTEGER,
papServerFreeJobs INTEGER,
papServerAuthenticationFailures Counter,
papServerAccountingFailures Counter,
papServerGeneralFailures Counter,
papServerState INTEGER,
papServerLastStatusMsg DisplayString
}
papServerIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An unique value for each Printer Access Protocol
Server."
::= { papServerEntry 1 }
Waldbusser & Frisa [Page 61]
RFC 1742 AppleTalk MIB II January 1995
papServerListeningSocket OBJECT-TYPE
SYNTAX DdpSocketAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Server Listening Socket that this PAP server is
listening on."
::= { papServerEntry 2 }
papServerStatus OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The status string of this server. This is the
message as it would appear in a PAP Status Reply
from this server."
::= { papServerEntry 3 }
papServerCompletedJobs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of jobs that have been accepted and
successfully executed by this server."
::= { papServerEntry 4 }
papServerBusyJobs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of GetNextJob calls that have accepted
and are currently executing a job."
::= { papServerEntry 5 }
papServerFreeJobs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The minimum number of GetNextJob calls that are
currently waiting for a job."
::= { papServerEntry 6 }
Waldbusser & Frisa [Page 62]
RFC 1742 AppleTalk MIB II January 1995
papServerAuthenticationFailures OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times this PAP server rejected a job
because the job was not correctly authenticated."
::= { papServerEntry 7 }
papServerAccountingFailures OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times this PAP server rejected a job
because the job did not fit some accounting rule,
such as exceeding a quota."
::= { papServerEntry 8 }
papServerGeneralFailures OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times this PAP server rejected a job
for some reason other than authentication or
accounting failures."
::= { papServerEntry 9 }
papServerState OBJECT-TYPE
SYNTAX INTEGER {
valid(1),
invalid(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The state of this PAP Server entry.
Setting this object to the value invalid(2) has the
effect of invalidating the corresponding entry in
the papServerTable. That is, it effectively
disassociates the mapping identified with said
entry. It is an implementation-specific matter as
to whether the agent removes an invalidated entry
from the table. Accordingly, management stations
must be prepared to receive from agents tabular
information corresponding to entries not currently
Waldbusser & Frisa [Page 63]
RFC 1742 AppleTalk MIB II January 1995
in use. Proper interpretation of such entries
requires examination of the relevant papServerState
object."
::= { papServerEntry 10 }
papServerLastStatusMsg OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The last status message that was transmitted by
this server."
::= { papServerEntry 11 }
-- The ASP Group
--
-- Implementation of this group is mandatory for all entities
-- that implement ASP
aspInputTransactions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ASP requests and replies received by
this entity. Note that this is not necessarily the
number of packets containing ASP transactions."
::= { asp 1 }
aspOutputTransactions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ASP requests and replies sent by this
entity. Note that this is not necessarily the number
of packets containing ASP transactions."
::= { asp 2 }
aspInOpenSessions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ASP Open Session requests and replies
received by this entity."
::= { asp 3 }
Waldbusser & Frisa [Page 64]
RFC 1742 AppleTalk MIB II January 1995
aspOutOpenSessions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ASP Open Session requests and replies
sent by this entity."
::= { asp 4 }
aspInCloseSessions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ASP Close Session requests and replies
received by this entity."
::= { asp 5 }
aspOutCloseSessions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ASP Close Session requests and replies
sent by this entity."
::= { asp 6 }
aspNoMoreSessionsErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times an error condition was returned
because this server implementation could not support
another session."
::= { asp 7 }
aspTickleTimeOutCloses OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the ASP entity on this node
closed a connection because it didn't receive any
messages from the remote end before its timer
expired."
::= { asp 8 }
Waldbusser & Frisa [Page 65]
RFC 1742 AppleTalk MIB II January 1995
aspConnTable OBJECT-TYPE
SYNTAX SEQUENCE OF AspConnEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of ASP connections on this entity."
::= { asp 9 }
aspConnEntry OBJECT-TYPE
SYNTAX AspConnEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A set of information describing an ASP connection.
As an example, an instance of the aspConnState object
might be named
aspConnState.0.80.220.135.0.80.239.119.12"
INDEX { aspConnLocalAddress, aspConnRemoteAddress,
aspConnID }
::= { aspConnTable 1 }
AspConnEntry ::= SEQUENCE {
aspConnLocalAddress DdpSocketAddress,
aspConnRemoteAddress DdpSocketAddress,
aspConnID INTEGER (1..255),
aspConnLastReqNum INTEGER (1..65535),
aspConnServerEnd INTEGER,
aspConnState INTEGER
}
aspConnLocalAddress OBJECT-TYPE
SYNTAX DdpSocketAddress
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The local address of this ASP connection."
::= { aspConnEntry 1 }
aspConnRemoteAddress OBJECT-TYPE
SYNTAX DdpSocketAddress
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The remote address of this ASP connection. If
this entry is in the listening mode, this object
shall have a value of four octets of zero."
::= { aspConnEntry 2 }
Waldbusser & Frisa [Page 66]
RFC 1742 AppleTalk MIB II January 1995
aspConnID OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The remote Connection ID of this ASP connection. If
this entry is in the listening mode, this object
shall have a value of zero."
::= { aspConnEntry 3 }
aspConnLastReqNum OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The last request number on this ASP connection. If
this entry is in the listening mode, this object
shall have a value of zero."
::= { aspConnEntry 4 }
aspConnServerEnd OBJECT-TYPE
SYNTAX INTEGER {
sss(1), -- Server Session Socket
wss(2), -- Workstation Session Socket
sls(3) -- Server Listening Socket
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Specifies what mode the local session end is in."
::= { aspConnEntry 5 }
aspConnState OBJECT-TYPE
SYNTAX INTEGER {
open(1),
closed(2),
invalid(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The state of this ASP connection.
Setting this object to the value invalid(3) has the
effect of invalidating the corresponding entry in the
aspConnTable. That is, it effectively disassociates
the mapping identified with said entry. It is an
implementation-specific matter as to whether the agent
removes an invalidated entry from the table.
Waldbusser & Frisa [Page 67]
RFC 1742 AppleTalk MIB II January 1995
Accordingly, management stations must be prepared to
receive from agents tabular information corresponding
to entries not currently in use. Proper
interpretation of such entries requires examination
of the relevant aspConnState object."
::= { aspConnEntry 6 }
-- The ADSP Group
--
-- Implementation of this group is mandatory for all entities
-- that implement ADSP
adspInPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ADSP packets received by this entity."
::= { adsp 1 }
adspOutPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ADSP packets sent by this entity."
::= { adsp 2 }
adspInOctets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of data octets contained in ADSP packets
received by this entity. Note that this does not
include EOM bits."
::= { adsp 3 }
adspOutOctets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of data octets contained in ADSP packets
sent by this entity. Note that this does not include
EOM bits."
Waldbusser & Frisa [Page 68]
RFC 1742 AppleTalk MIB II January 1995
::= { adsp 4 }
adspInDataPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ADSP data packets this entity has
received."
::= { adsp 5 }
adspOutDataPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ADSP data packets this entity has
sent."
::= { adsp 6 }
adspTimeoutErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the ADSP on this entity detected
an expired connection timer."
::= { adsp 7 }
adspTimeoutCloseErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the ADSP on this entity closed a
connection because of too many timeouts."
::= { adsp 8 }
adspConnTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdspConnEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of ADSP connections on this entity."
::= { adsp 9 }
adspConnEntry OBJECT-TYPE
SYNTAX AdspConnEntry
Waldbusser & Frisa [Page 69]
RFC 1742 AppleTalk MIB II January 1995
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A set of information describing an ADSP connection.
As an example, an instance of the adspConnState object
might be named
adspConnState.0.80.220.7.0.80.239.142.31231"
INDEX { adspConnLocalAddress, adspConnRemoteAddress,
adspConnLocalConnID }
::= { adspConnTable 1 }
AdspConnEntry ::= SEQUENCE {
adspConnLocalAddress DdpSocketAddress,
adspConnLocalConnID INTEGER (0..65535),
adspConnRemoteAddress DdpSocketAddress,
adspConnRemoteConnID INTEGER (0..65535),
adspConnState INTEGER
}
adspConnLocalAddress OBJECT-TYPE
SYNTAX DdpSocketAddress
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The local DDP address of this ADSP connection."
::= { adspConnEntry 1 }
adspConnLocalConnID OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The local Connection ID of this ADSP connection. If
this entry specifies an ADSP listener, this value
shall be zero."
::= { adspConnEntry 2 }
adspConnRemoteAddress OBJECT-TYPE
SYNTAX DdpSocketAddress
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The remote DDP address of this ADSP connection. If
this entry specifies an ADSP listener, this value
shall be zero."
::= { adspConnEntry 3 }
adspConnRemoteConnID OBJECT-TYPE
Waldbusser & Frisa [Page 70]
RFC 1742 AppleTalk MIB II January 1995
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The remote Connection ID of this ADSP connection.
If this entry specifies an ADSP listener, this value
shall be zero."
::= { adspConnEntry 4 }
adspConnState OBJECT-TYPE
SYNTAX INTEGER {
open(1),
localHalfOpen(2),
remoteHalfOpen(3),
listening(4),
closed(5),
invalid(6)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The state of this ADSP connection. The state is
open if both ends are established. If only one end
is established, then the state is half-open. If
neither end is established, then the state is
closed. If an ADSP server is listening on a socket
and is not yet connected, its state is set to
listening, and the adspConnRemoteAddress,
adspConnRemoteSocket, adspConnRemoteConnID, and
adspConnRemoteWindowSize are all set to zero.
Setting this object to the value invalid(6) has the
effect of invalidating the corresponding entry in
the adspConnTable. That is, it effectively
disassociates the mapping identified with said
entry. It is an implementation-specific matter as
to whether the agent removes an invalidated entry
from the table. Accordingly, management stations
must be prepared to receive from agents tabular
information corresponding to entries not currently
in use. Proper interpretation of such entries
requires examination of the relevant adspConnState
object."
::= { adspConnEntry 5 }
Waldbusser & Frisa [Page 71]
RFC 1742 AppleTalk MIB II January 1995
-- The ATPortPtoP Group
--
-- Implementation of this group is mandatory for all entities
-- that implement AppleTalk point-to-point links
atportPtoPTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtportPtoPEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of AppleTalk point-to-point connections for
this entity."
::= { atportptop 1 }
atportPtoPEntry OBJECT-TYPE
SYNTAX AtportPtoPEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The description of one of the AppleTalk
point-to-point connections on this entity.
As an example, an instance of the
atportPtoPRemoteAddress object might be named
atportPtoPRemoteAddress.2"
INDEX { atportPtoPIndex }
::= { atportPtoPTable 1 }
AtportPtoPEntry ::= SEQUENCE {
atportPtoPIndex INTEGER,
atportPtoPProtocol OBJECT IDENTIFIER,
atportPtoPRemoteName DisplayString,
atportPtoPRemoteAddress OCTET STRING,
atportPtoPPortIndex INTEGER,
atportPtoPStatus INTEGER
}
atportPtoPIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A unique value for each AppleTalk point-to-point
connection. Its value is between 1 and the total
number of AppleTalk point-to-point connections. The
value for each connection must remain constant at
least from the re-initialization of the entity's
network management system to the next
Waldbusser & Frisa [Page 72]
RFC 1742 AppleTalk MIB II January 1995
re-initialization."
::= { atportPtoPEntry 1 }
atportPtoPProtocol OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The protocol type used over the point-to-point
connection."
::= { atportPtoPEntry 2 }
atportPtoPRemoteName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A text string containing the network node name of the
entity at the other end of the point-to-point link.
If the name is unknown or undefined, then this
string is zero length."
::= { atportPtoPEntry 3 }
atportPtoPRemoteAddress OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The network address of the entity at the other end
of the point-to-point link in network byte order.
The format of this address can be determined
by examinating the atportType corresponding to this
entry. If the address is unknown or undefined, then
this string is zero length."
::= { atportPtoPEntry 4 }
atportPtoPPortIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The AppleTalk port associated with this
point-to-point connection. The interface identified
by a particular value of this index is the same
interface as identified by the same value of
atportIndex."
::= { atportPtoPEntry 5 }
Waldbusser & Frisa [Page 73]
RFC 1742 AppleTalk MIB II January 1995
atportPtoPStatus OBJECT-TYPE
SYNTAX INTEGER {
valid(1),
invalid(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of this entry in the atportPtoPTable.
Setting this object to the value invalid(2) has the
effect of invalidating the corresponding entry in
the atportPtoPTable. That is, it effectively
disassociates the mapping identified with said
entry. It is an implementation-specific matter as
to whether the agent removes an invalidated entry
from the table. Accordingly, management stations
must be prepared to receive from agents tabular
information corresponding to entries not currently
in use. Proper interpretation of such entries
requires examinationr of the relevant
atportPtoPStatus object."
::= { atportPtoPEntry 6 }
atportPtoPProtoOids OBJECT IDENTIFIER ::= { atportptop 2 }
-- A list of values to be used for the atportPtoPProtocol
-- variable.
-- When new protocols are defined, their oids may be defined
-- in separate MIB documents in different branches of the tree.
pToPProtoOther OBJECT IDENTIFIER ::= { atportPtoPProtoOids 1 }
pToPProtoAurp OBJECT IDENTIFIER ::= { atportPtoPProtoOids 2 }
pToPProtoCaymanUdp OBJECT IDENTIFIER ::=
{ atportPtoPProtoOids 3 }
pToPProtoAtkvmsDecnetIV OBJECT IDENTIFIER ::=
{ atportPtoPProtoOids 4 }
pToPProtoLiaisonUdp OBJECT IDENTIFIER ::=
{ atportPtoPProtoOids 5 }
pToPProtoIpx OBJECT IDENTIFIER ::= { atportPtoPProtoOids 6 }
pToPProtoShivaIp OBJECT IDENTIFIER ::=
{ atportPtoPProtoOids 7 }
Waldbusser & Frisa [Page 74]
RFC 1742 AppleTalk MIB II January 1995
-- The Per Port Counters Group
--
-- Implementation of this group is optional.
perPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF PerPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The table of per-port statistics for this entity."
::= { perPort 1 }
perPortEntry OBJECT-TYPE
SYNTAX PerPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The statistics available for a particular port on
this entity.
As an example, an instance of the perPortAarpInProbes
object might be named perPortAarpInProbes.2"
INDEX { atportIndex }
::= { perPortTable 1 }
PerPortEntry ::= SEQUENCE {
perPortAarpInProbes Counter,
perPortAarpOutProbes Counter,
perPortAarpInReqs Counter,
perPortAarpOutReqs Counter,
perPortAarpInRsps Counter,
perPortAarpOutRsps Counter,
perPortDdpInReceives Counter,
perPortDdpInLocalDatagrams Counter,
perPortDdpNoProtocolHandlers Counter,
perPortDdpTooShortErrors Counter,
perPortDdpTooLongErrors Counter,
perPortDdpChecksumErrors Counter,
perPortDdpForwRequests Counter,
perPortRtmpInDataPkts Counter,
perPortRtmpOutDataPkts Counter,
perPortRtmpInRequestPkts Counter,
perPortRtmpRouteDeletes Counter,
perPortZipInZipQueries Counter,
perPortZipInZipReplies Counter,
perPortZipInZipExtendedReplies Counter,
perPortZipZoneConflictErrors Counter,
perPortZipInErrors Counter,
Waldbusser & Frisa [Page 75]
RFC 1742 AppleTalk MIB II January 1995
perPortNbpInLookUpRequests Counter,
perPortNbpInLookUpReplies Counter,
perPortNbpInBroadcastRequests Counter,
perPortNbpInForwardRequests Counter,
perPortNbpOutLookUpReplies Counter,
perPortNbpRegistrationFailures Counter,
perPortNbpInErrors Counter,
perPortEchoRequests Counter,
perPortEchoReplies Counter
}
perPortAarpInProbes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of AARP Probe packets received
by this entity on this port."
::= { perPortEntry 1 }
perPortAarpOutProbes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of AARP Probe packets sent by
this entity on this port."
::= { perPortEntry 2 }
perPortAarpInReqs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of AARP Request packets received
by this entity on this port."
::= { perPortEntry 3 }
perPortAarpOutReqs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of AARP Request packets sent by
this entity on this port."
::= { perPortEntry 4 }
Waldbusser & Frisa [Page 76]
RFC 1742 AppleTalk MIB II January 1995
perPortAarpInRsps OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of AARP Response packets received
by this entity on this port."
::= { perPortEntry 5 }
perPortAarpOutRsps OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of AARP Response packets sent by
this entity on this port."
::= { perPortEntry 6 }
perPortDdpInReceives OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input datagrams received by DDP
on this port, including those received in error."
::= { perPortEntry 7 }
perPortDdpInLocalDatagrams OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams on this
port for which this entity was their final DDP
destination."
::= { perPortEntry 8 }
perPortDdpNoProtocolHandlers OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of DDP datagrams addressed to this
entity on this port that were addressed to an upper
layer protocol for which no protocol handler
existed."
::= { perPortEntry 9 }
Waldbusser & Frisa [Page 77]
RFC 1742 AppleTalk MIB II January 1995
perPortDdpTooShortErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams on this
port dropped because the received data length was
less than the data length specified in the DDP
header or the received data length was less than the
length of the expected DDP header."
::= { perPortEntry 10 }
perPortDdpTooLongErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams on this
port dropped because they exceeded the maximum DDP
datagram size."
::= { perPortEntry 11 }
perPortDdpChecksumErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input DDP datagrams on this
port for which this DDP entity was their final
destination, and which were dropped because of a
checksum error." ::= { perPortEntry 12 }
perPortDdpForwRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of input datagrams on this port for
which this entity was not their final DDP
destination, as a result of which an attempt was
made to find a route to forward them to that final
destination."
::= { perPortEntry 13 }
perPortRtmpInDataPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
Waldbusser & Frisa [Page 78]
RFC 1742 AppleTalk MIB II January 1995
STATUS mandatory
DESCRIPTION
"A count of the number of good RTMP data packets
received by this entity on this port."
::= { perPortEntry 14 }
perPortRtmpOutDataPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of RTMP packets sent by this
entity on this port."
::= { perPortEntry 15 }
perPortRtmpInRequestPkts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of good RTMP Request packets
received by this entity on this port."
::= { perPortEntry 16 }
perPortRtmpRouteDeletes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of times RTMP deletes a route
on this port because it was aged out of the table."
::= { perPortEntry 17 }
perPortZipInZipQueries OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP Queries received by this entity
on this port."
::= { perPortEntry 18 }
perPortZipInZipReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
Waldbusser & Frisa [Page 79]
RFC 1742 AppleTalk MIB II January 1995
"The number of ZIP Replies received by this entity
on this port."
::= { perPortEntry 19 }
perPortZipInZipExtendedReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP Extended Replies received by this
entity on this port."
::= { perPortEntry 20 }
perPortZipZoneConflictErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times a conflict has been detected on
this port between this entity's zone information and
another entity's zone information."
::= { perPortEntry 21 }
perPortZipInErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ZIP packets received by this entity
on this port that were rejected for any error."
::= { perPortEntry 22 }
perPortNbpInLookUpRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP LookUp Requests received on this
port."
::= { perPortEntry 23 }
perPortNbpInLookUpReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP LookUp Replies received on this
Waldbusser & Frisa [Page 80]
RFC 1742 AppleTalk MIB II January 1995
port."
::= { perPortEntry 24 }
perPortNbpInBroadcastRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP Broadcast Requests received on
this port."
::= { perPortEntry 25 }
perPortNbpInForwardRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP Forward Requests received on this
port."
::= { perPortEntry 26 }
perPortNbpOutLookUpReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP LookUp Replies sent on this port."
::= { perPortEntry 27 }
perPortNbpRegistrationFailures OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times this node experienced a failure
in attempting to register an NBP entity on this
port."
::= { perPortEntry 28 }
perPortNbpInErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of NBP packets received by this entity
on this port that were rejected for any error."
::= { perPortEntry 29 }
Waldbusser & Frisa [Page 81]
RFC 1742 AppleTalk MIB II January 1995
perPortEchoRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of AppleTalk Echo requests received on
this port."
::= { perPortEntry 30 }
perPortEchoReplies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The count of AppleTalk Echo replies received on
this port."
::= { perPortEntry 31 }
END
6. Acknowledgments
This document was produced by the IETF AppleTalk-IP Working Group.
In addition, the contribution of the following individuals is also
acknowledged:
Greg Bruell, Wellfleet
Phil Budne, Shiva
Robert Jeckell, 3Com
Greg Merrell, DEC
Greg Minshall, Novell, Inc.
Bob Morgan, Stanford University
Brad Parker, FCR
Marshall T. Rose, Dover Beach Consulting
Wayne Tackabury, Cayman
Jonathan Wenocur, Shiva
Waldbusser & Frisa [Page 82]
RFC 1742 AppleTalk MIB II January 1995
7. References
[1] Cerf, V., "IAB Recommendations for the Development of Internet
Network Management Standards", RFC 1052, IAB, April 1988.
[2] Cerf, V., "Report of the Second Ad Hoc Network Management Review
Group", RFC 1109, IAB, August 1989.
[3] Rose M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based internets", STD 16, RFC
1155, Performance Systems International, Hughes LAN Systems, May
1990.
[4] McCloghrie K., and M. Rose, "Management Information Base for
Network Management of TCP/IP-based internets", RFC 1156, Hughes
LAN Systems, Performance Systems International, May 1990.
[5] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, SNMP Research,
Performance Systems International, Performance Systems
International, MIT Laboratory for Computer Science, May 1990.
[6] Rose, M., Editor, "Management Information Base for Network
Management of TCP/IP-based internets: MIB-II", RFC 1158,
Performance Systems International, May 1990.
[7] Information processing systems - Open Systems Interconnection -
Specification of Abstract Syntax Notation One (ASN.1),
International Organization for Standardization, International
Standard 8824, December 1987.
[8] Information processing systems - Open Systems Interconnection -
Specification of Basic Encoding Rules for Abstract Notation One
(ASN.1), International Organization for Standardization,
International Standard 8825, December 1987.
[9] Rose, M., and K. McCloghrie, Editors, "Concise MIB Definitions",
STD 16, RFC 1212, Performance Systems International, Hughes LAN
Systems, March 1991.
[10] Gursharan S., Andrews, R., and A. Oppenheimer, "Inside
AppleTalk", Second Edition, Addison Wesley, 1990.
Waldbusser & Frisa [Page 83]
RFC 1742 AppleTalk MIB II January 1995
Security Considerations
Security issues are not discussed in this memo.
9. Authors' Addresses
Steven Waldbusser
Carnegie Mellon University
5000 Forbes Ave.
Pittsburgh, PA 15213
Phone: 412-268-6628
EMail: waldbusser@cmu.edu
Karen Frisa
FORE Systems, Inc.
174 Thorn Hill Road
Warrendale, PA 15086-7535
Phone: 412-772-6541
EMail: kfrisa@fore.com
Waldbusser & Frisa [Page 84]