💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc2024.txt captured on 2022-07-16 at 22:29:13.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group D. Chen, Editor
Request for Comments: 2024 P. Gayek
Category: Standards Track IBM
S. Nix
Metaplex, Inc.
October 1996
Definitions of Managed Objects for Data Link Switching
using SMIv2
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Abstract
This specification defines an extension to the Management Information
Base (MIB) for use with SNMP-based network management. In
particular, it defines objects for configuring, monitoring, and
controlling Data Link Switches (DLSw) [1].
This memo specifies a MIB module in a manner that is both compliant
to the SNMPv2 SMI [2], and semantically identical to the SNMPv1
definitions [3].
Table of Contents
1.0 The SNMPv2 Network Management Framework . . . . . . . . . 2
1.1 Object Definitions . . . . . . . . . . . . . . . . . . . . 2
2.0 Overview . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.1 Relation to Interface Group (RFC 1573) [8] . . . . . . . . . 2
2.2 Relation to Underlying DLC Layer . . . . . . . . . . . . . 3
2.3 Relation to SDLC MIB (RFC 1747) . . . . . . . . . . . . . 3
2.4 DLSw MIB Structure . . . . . . . . . . . . . . . . . . . . 4
2.4.1 Compliance . . . . . . . . . . . . . . . . . . . . . . 4
2.5 DLSw MIB Usage . . . . . . . . . . . . . . . . . . . . . . 5
2.5.1 Cooperative DLSw nodes . . . . . . . . . . . . . . . . 5
2.5.2 Setting capabilities exchange-related objects . . . . 5
2.5.3 Examples of Tasks Using This MIB . . . . . . . . . . . 6
3.0 Definitions . . . . . . . . . . . . . . . . . . . . . . . 11
4.0 Acknowledgements . . . . . . . . . . . . . . . . . . . . . 89
5.0 References . . . . . . . . . . . . . . . . . . . . . . . . 89
6.0 Security Considerations . . . . . . . . . . . . . . . . . 90
Chen, et. al. Standards Track [Page 1]
RFC 2024 DLSw MIB using SMIv2 October 1996
7.0 Authors' Addresses . . . . . . . . . . . . . . . . . . . . 90
1.0 The SNMPv2 Network Management Framework
The SNMP Network Management Framework presently consists of three
major components. They are:
RFC 1902 [2] which defines the SMI, the mechanisms used for
describing and naming objects for the purpose of management.
STD 17, RFC 1213 [4] defines MIB-II, the core set of managed
objects for the Internet suite of protocols.
STD 15, RFC 1157 [5] and RFC 1905 [6] which define two versions of
the protocol used for network access to managed objects.
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
1.1 Object Definitions
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the subset of Abstract Syntax Notation One (ASN.1)
defined in the SMI. In particular, each object type is named by an
OBJECT IDENTIFIER, an administratively assigned name. The object
type together with an object instance serves to uniquely identify a
specific instantiation of the object. For human convenience, we
often use a textual string, termed the descriptor, to refer to the
object type.
2.0 Overview
This memo identifies the set of objects for configuring, monitoring,
and controlling Data Link Switches.
2.1 Relation to Interface Group (RFC 1573) [8]
o ifIndex is used as the index into dlswIfTable, which shows and
controls the interfaces that DLSw is active on.
o Local entries in the MAC address and NetBIOS (NB) name caches can
point to an ifEntry to indicate the interface through which DLSw can
reach that MAC address or NB name. See the objects
dlswDirMacLocation and dlswDirNBLocation.
o Local entries in the circuit table use ifIndex to indicate the
interface through which DLSw is connected to the local end station.
Chen, et. al. Standards Track [Page 2]
RFC 2024 DLSw MIB using SMIv2 October 1996
See the object dlswCircuitS1Index.
o ifIndex is the primary index into dlswSdlcLsTable, which lists the
SDLC stations DLSw is serving.
2.2 Relation to Underlying DLC Layer
The DLSw MIB does not duplicate the information in the MIBs for the
DLC layer underneath it. Instead, each circuit table entry contains
a pointer to a conceptual row in an underlying enterprise-specific or
standard DLC MIB.
Using the 802.2 LLC management as an example, the following rules
should be considered when developing new DLSw related DLC MIBs, and
when implementing the interactions between DLSw MIB and DLC MIBs:
o The referenced row should represent the local LLC-2 (and/or LLC-1,
if supported) link station that DLSw is using. In the current 802.2
LLC MIB draft, this might be a row of one of the tables
llcCcAdminTable, llcCcOperTable, or llcCcStatsTable.
A circuit using local LLC services will therefore have
dlswCircuitS1DlcType = llc, and dlswCircuitS1Dlc = pointer to an LLC
MIB table row.
o Because DLSw is the user of LLC services, it is generally preferable
to initiate administrative actions using the DLSw MIB and allow DLSw
to control LLC directly, rather than starting with LLC MIB
administrative actions. For example, a hung circuit should be
disconnected by setting dlswCircuitState, as opposed to setting
llcCcAdminStatus to disable the LLC part of the circuit. Similarly,
setting bits in dlswIfSapList will cause row creation in
llcSapOperTable as well as set the necessary DLSw-LLC relationship.
2.3 Relation to SDLC MIB (RFC 1747)
The general comments stated in 2.2, "Relation to Underlying DLC
Layer" apply to the SDLC MIB. The following apply if the DLSw MIB is
implemented in a product that also implements RFC 1747 [9]:
o The row referenced from dlswCircuitS1Dlc should represent the local
SDLC link station that DLSw is using. This might be a row of one of
the tables sdlcLSAdminTable, sdlcLSOperTable, or sdlcLSStatsTable.
A circuit using local SDLC services will therefore have
dlswCircuitS1DlcType = sdlc, and dlswCircuitS1Dlc = OID of one of
these table rows.
Chen, et. al. Standards Track [Page 3]
RFC 2024 DLSw MIB using SMIv2 October 1996
o dlswSdlcLsTable uses the same indices that are used to index link
station information in RFC 1747. This table provides a mapping
between this native SDLC addressing (interface, link station
address) and the addressing used in the DLSw domain (local MAC and
SAP).
2.4 DLSw MIB Structure
See 3 .0, "Definitions" on page 11 for a diagram outlining the DLSw
MIB structure. The following groups of objects are included:
dlswNode Objects related to this DLSw node's configuration,
monitoring and control.
dlswTConn Objects relating to transport connections to this
DLSw's partner nodes.
dlswInterface Objects configured for this DLSw relating to its local
interfaces.
dlswDirectory Objects reflecting this DLSw's view of where
end-station resources (MAC addresses and NetBIOS names)
are located.
dlswCircuit Objects showing the end-station connections that
DLSw currently has established, or that are coming up
or have gone down.
dlswSDLC Objects configured for this DLSw's SDLC-attached end
stations.
2.4.1 Compliance
The MIB provides the following compliance statements:
dlswCoreCompliance Defines the minimum support required of all
implementations. Note that for this and the
other compliance statements, NetBIOS-related
objects are grouped separately because the
DLSw Version 1 Standard [1] does not require
NetBIOS support.
dlswTConnTCPCompliance Defines the minimum support required of
implementations that use TCP as a transport
protocol.
dlswDirCompliance Defines the minimum support required of
implementations that support some sort of
Chen, et. al. Standards Track [Page 4]
RFC 2024 DLSw MIB using SMIv2 October 1996
directory function.
dlswDirLocateCompliance Defines the minimum support required of
implementations that support a directory
function and also support the ordered
retrieval of the entries that match a given
resource.
dlswSdlcCompliance Defines the minimum support required of
implementations that support SDLC-attached
end stations.
2.5 DLSw MIB Usage
2.5.1 Cooperative DLSw nodes
To reduce the size of the MIB, thus the amount of data that each
agent needs to keep, the information that usually could be made
available in two partner nodes (e.g., information exchanged between
them) is only defined in the MIB as the info received. That is,
there are no objects defined for the info sent. In order to form the
complete picture of the state of a resource, the manager needs to
retrieve info from multiple DLSw nodes. An example is that the SAP
list, NETBIOS list and MAC list are kept at the receiving end of a
DLSw capabilities exchange (the sender does not save what it sent to
each partner).
Note well: The DLSw protocol does not specify a technique for a
manager to correlate the transport address of the partner managed
DLSw node and the transport address that the management protocol
uses.
2.5.2 Setting capabilities exchange-related objects
This MIB supports changes to DLSw variables whose change should be
reported to DLSw partner nodes in a "run-time" capabilities exchange.
Since a DLSw node normally unicasts these capabilities messages to
all its active partners, frequent changes to these variables can
result in excessive network traffic. To avoid this problem,
developers of network management applications using this MIB should
try to group all such changes in a few SNMP SET requests, and should
send them in bulk. Agent developers should implement a technique to
group a number of changes into a single capabilities exchange
message. One possible approach is to send a run-time capabilities
message only if no capabilities-related changes have been received
for a pre-defined period of time.
Chen, et. al. Standards Track [Page 5]
RFC 2024 DLSw MIB using SMIv2 October 1996
2.5.3 Examples of Tasks Using This MIB
2.5.3.1 Configuring DLSw to actively connect to a specific TCP/IP
partner
Create a conceptual row in dlswTConnConfigTable with: Index = the
highest the managed station has used so far + 1; TDomain =
dlswTCPDomain; LocalTAddr = this node's DLSw IP address; RemoteTAddr
= the partner's DLSw IP address; EntryType = individual; SetupType =
activePersistent. Note that determining the index to use may require
dumping the TConnConfigTable, but this will not typically be a large
table. If the DLSw node rejects the row creation due to index
collision, the management station should increment its index value
and try again.
2.5.3.2 Configuring DLSw to passively accept any partner
Create a conceptual row in dlswTConnConfigTable as above but with:
RemoteTAddr = 0; EntryType = global; SetUpType = passive. Every
individual transport connection accepted as a result of this global
row will inherit the configuration values from this row.
To prevent a specific remote node from being passively accepted as a
partner, create another row with: RemoteTAddr = that node's IP
address; EntryType = individual; SetupType = excluded.
2.5.3.3 Configuring DLSw to allow or connect to a group of partners
Define a conceptual row in dlswTConnConfigTable as above but with:
EntryType = group; GroupDefinition = pointer to an enterprise-
specific representation of a group. For example, a group definition
might consist of an IP address value and mask, or a multicast IP
address. Every individual transport connection accepted as a result
of this group row will inherit the configuration values from this
row.
When a group is created that has some overlap with entries where
EntryType = individual (there will always be this overlap when a
global row exists), the DLSw node must use the configured rows using
a "most specific match wins" rule. That is, the entry in
TConnConfigTable with the remote address most nearly matching an
incoming connection should be used to provide the values for the new
connection. For equal matches, the choice of TConnConfigTable entry
is up to the DLSw node implementation. Note that the management
station should never create two TConnConfig rows with duplicate
remote addressing values.
Chen, et. al. Standards Track [Page 6]
RFC 2024 DLSw MIB using SMIv2 October 1996
2.5.3.4 Identifying the protocol level of a partner DLSw
If the partner DLSw has implemented at least the AIW Version 1 DLSw
Standard [1], the AIW version and release number for the DLSw
protocol is accessible from dlswTConnOperPartnerVersion. If
TConnOperPartnerVersion is a string of zero length but the
TConnOperState = `connected' state (i.e., is not still performing
capabilities exchange), the partner DLSw can be assumed to be an RFC
1434+ node.
2.5.3.5 Recycling a transport connection
Quiesce or forcibly disconnect the transport connection by setting
TConnOperState to `quiescing' or `disconnecting', and monitor until
it moves to the `disconnected' state or the TConnOper row disappears.
The row may disappear because implementations are not required to
maintain transport connection information after a transport
connection has gone down.
The action required to re-activate the transport connection depends
on the value of TConnConfigSetupType for the relevant TConnConfig
row. ActivePersistent connections will attempt to come back
automatically. Passive connections must be re-established from the
remote partner. ActiveOnDemand connections will be re-established by
this node, but only after some end-station operation triggers a
circuit setup attempt.
2.5.3.6 Investigating why a transport connection went down
TConnOperDiscTime and TConnOperDiscReason provide the vital
information of the time and the cause of the disconnection of a
transport connection and TConnOperDiscActiveCir indicates whether end
users may have been affected. This MIB does not specify the duration
that an agent must make this information available after the
disconnection of a transport connection occurs. Manager should try
the agent of the partner DLSw, if such information is not available
in one DLSw node. Additional information might come from the MIB for
the transport protocol (e.g., TCP or LLC). dlswTConnStat* and
dlswTConnConfigOpens give a more general picture of transport
connection activity, but can't give specific reasons for problems.
2.5.3.7 Changing the configuration of an active transport connection
Follow this sequence of managment protocol set operations:
1. Use TConnOperConfigIndex to locate the TConnConfig entry that
governs the configuration of the transport connection.
Chen, et. al. Standards Track [Page 7]
RFC 2024 DLSw MIB using SMIv2 October 1996
2. Change the rowStatus of that conceptual row to notInService. This
prevents the transport connection from being connected automatically
if TConnConfigSetupType = activePersistent.
3. Quiesce or forcibly disconnect the transport connection by setting
TConnOperState to `quiescing' or `disconnecting', and monitor until
it moves to the `disconnected' state or the TConnOper row
disappears.
4. Change the values of TConnConfig variables as desired.
5. Change the rowStatus of the TConnConfig conceptual row to active.
TConnConfigSetupType will subsequently control whether this node
will actively seek to re-establish the transport connection, or will
wait.
2.5.3.8 Checking configuration validity for an active transport
connection
Use TConnOperConfigIndex to identify the row of TConnConfig for the
transport connection. If TConnConfigLastModifyTime is greater than
TConnOperConnectTime, then one or more of the variables in the
TConnConfig row may not be valid for the current state of the active
transport connection. This is an exception condition and will not
normally be the case.
2.5.3.9 Configuring the interfaces and SAPs DLSw will use
To add DLSw end-station support (not transport connection support) to
an interface, create a conceptual row for that ifIndex in the
dlswIfTable. For many products, you will specify the same single
virtual segment number for all interfaces. Indicate the list of SAPs
to be supported by that interface - this could be all 0xFFs if the
product has some automatic SAP opening function.
To open or close a SAP to DLSw on an existing interface, simply set
or reset the appropriate bit in dlswIfSapList in the table row for
that interface.
2.5.3.10 Configuring static MAC address (or NetBIOS name) cache entries
It is common to configure a few static directory entries to preload
in the caches of the DLSw nodes and reduce the need for broadcast
searches. The following example adds entries to the MAC cache to
indicate that a specific MAC address is reachable through two
different remote partners:
1. The manager retrieves dlswDirMacCacheNextIndex to get an index
assignment from the DLSw node. The DLSw node ensures that the
retrieved index will not be reused.
Chen, et. al. Standards Track [Page 8]
RFC 2024 DLSw MIB using SMIv2 October 1996
2. The manager creates a conceptual row in dlswDirMacTable with:
Index = the retrieved index; Mac = the MAC address; Mask = all
0xFF's; EntryType = userConfiguredPublic; LocationType = remote;
Location = OID for dlswTConnConfigEntry of the 1st partner; Status
= unknown (recommended for new entries).
3. The manager repeats the preceding 2 steps and creates a second row
using Index = second index retrieved; Location = OID for
dlswTConnConfigEntry of the 2nd partner.
Note that the DLSw node is not obligated to use newly created
directory entries in the order in which they were created. It is
recommended that entries be used in most-specific match first order,
i.e., an entry with a Mask of all 0xFFs should take precedence over
one with a "partial wildcard". The relative order of static versus
dynamic entries and of "equal length" matches is up to the DLSw
implementation.
The dlswDirStat objects can be used to get an idea of the success
rate for a particular static caching scheme.
2.5.3.11 Seeing where the directory indicates a given resource is
To retrieve all directory information related to a given resource (in
this example, a NetBIOS name), the management station should:
1. Retrieve dlswDirLocateNBLocation in the dlswDirLocateNBTable entry
where NBName = the fully-specified NetBIOS name without wildcards;
NBMatch = 1.
2. Use the returned value (i.e., OID) to retrieve the contents of the
dlswDirNBEntry itself.
3. Repeat the previous two steps with NBMatch = 2, 3, ..., until the
end of dlswDirLocateNBTable is reached.
The DLSw node conveys the precedence relationship of the different
matching directory entries by the order in which it returns their
OIDs.
2.5.3.12 Investigating circuit bringup failure
Circuit bringup takes place in two stages: explorer flows to locate
the target resource (MAC address or NetBIOS name); and establishing
the circuit itself. To determine the success of explorer flows, have
the origin end station initiate a link establishment to the target,
and look later for cache entries for the target MAC address or
NetBIOS name. The dlswTConn*ex* counters also give some visibility
to which transport connections are being used to look for resources.
Once circuit establishment is started, an entry of dlswCircuitTable
for the two MAC/SAP addresses involved is created.
Chen, et. al. Standards Track [Page 9]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswCircuitEntryTime, StateTime, and State may provide useful
information about intermediate states the circuit is reaching before
becoming disconnected again.
2.5.3.13 Investigating the failure of an established circuit
The variables dlswCircuitDiscReason* in the dlswCircuitTable provide
the key information of the cause of the disconnection of circuits.
In addition, the underlying DLC MIBs may provide information at the
link station level, and some clues (e.g., DISC or FRMR counters) at
the SAP or interface level.
2.5.3.14 Seeing circuit-level traffic statistics
Locate the relevant dlswCircuitEntry and follow dlswCircuitS1Dlc to a
link station-level table entry in the underlying DLC MIB. Move to
the corresponding link station's statistics table in the DLC MIB to
get counters of frames, bytes, etc. for this circuit.
2.5.3.15 Cutting down the flow of DLSw-related traps
Set some or all of the dlswTrapCntl* objects to the value of
`disabled' or `partial'.
Chen, et. al. Standards Track [Page 10]
RFC 2024 DLSw MIB using SMIv2 October 1996
3.0 Definitions
-- *******************************************************************
--
-- The structure of the DLSw MIB (t: indicates table):
-- DLSw MIB
-- |-- Node Group
-- | |-- Node Identity
-- | |-- Node Operational Related
-- | |-- Node Resource
-- |
-- |-- Transport Connection Group
-- | |-- Statistics
-- | |t- Transport Connection Configuration
-- | |t- Transport Connection Operation
-- | | |-- capabilities
-- | | |-- Supported SAP List
-- | | |-- statistics
-- | | |-- transport connection itself
-- | | |-- traffic over the transport connection
-- | | |-- directory search activities
-- | | |-- search filtered statistics
-- | | |-- circuits over the transport connection
-- | |-- Transport Specific
-- | |-- Tcp
-- | |t- Transport Connection Config (Tcp Specific)
-- | |t- Transport Connection Operation (Tcp Specific)
-- |
-- |-- Interface Group
-- | |t- interfaces that DLSw is active on.
-- |
-- |-- Directory Group
-- | |-- Statistics
-- | |-- Directory Cache
-- | | |t- Directory of MAC addresses
-- | | |t- Directory of NETBIOS names
-- | |-- Locate
-- | |t- Directory of Locate MAC
-- | |t- Directory of Locate NETBIOS
-- |
-- |-- Circuit Group
-- | |-- Statistics
-- | |t- Circuits
-- |
-- |-- Virtual and non-LAN end stations
-- | |t- SDLC end station
-- |
-- *******************************************************************
Chen, et. al. Standards Track [Page 11]
RFC 2024 DLSw MIB using SMIv2 October 1996
-- *******************************************************************
-- This MIB module contains objects necessary for management of Data
-- Link Switches.
--
-- Terminology:
-- (1) DLSw:
-- A device which provides data link switching function.
-- Sometimes it is referred as a DLSw or DLSw node.
-- Local DLSw: The DLSw that the DLSw SNMP Agent is running on.
-- Partner DLSw (or DLSw partner): A DLSw node that is "transport
-- connected" with the local DLSw. Sometimes the term "DLSw
-- partners" is used to indicate the two ends of a transport
-- connection.
--
-- (2) TCP Connection:
-- Full-duplex (-capable) association defined by a pair of
-- (IP address, port) pairs, running the TCP protocol. The port
-- addresses in RFC 1795 define two TCP connections between
-- a pair of DLSw nodes, each being used to send data in a
-- single direction.
-- Local: This end of TCP connection
-- Foreign: Remote end of TCP connection
--
-- (3) Transport Connection:
-- It is a generic term for a full-duplex reliable connection
-- between DLSw nodes. This term is used to refer to the
-- association between DLSw nodes without being concerned
-- about whether TCP is the protocol or whether there are
-- one or two TCP connection.
-- (Note: for two TCP connections, the transport connection is
-- opened if and only if both TCP connections are operational.
-- Also note: sometimes race conditions will occur, but the
-- condition should only be temporary.)
--
-- (4) Data Link:
-- An instance of OSI layer-2 procedures for exchanging information
-- using either connection-oriented (e.g., LLC-2) or connectionless
-- (e.g., LLC-1) services. A DLSw node or pair of partner nodes
-- switches data traffic from stations of one data link to
-- stations of another data link. Data link switching is
-- transparent to end stations.
-- Source: the end station which sends a message.
-- Destination: the end station which receives a message.
-- (This DLSw role is with respect to a give message)
--
-- (5) Circuit:
-- End-to-end association of two DLC entities through one or
-- two DLSw nodes. A circuit is the concatenation of two
Chen, et. al. Standards Track [Page 12]
RFC 2024 DLSw MIB using SMIv2 October 1996
-- "data links", optionally with an intervening transport
-- connection.
-- Origin: the end station which initiates the circuit.
-- Target: the end station which receives the initiation.
--
-- (6) Link Station:
-- It is one end of an LLC-2 connection. It performs error
-- recovery procedure, retries, and various timers.
-- DLSw terminates LLC-2 connection at each end of DLSw nodes,
-- thus, keepAlive and error recovery on LLC-2 connections are
-- kept to each side of LAN and do not flow through the WAN.
-- A link station is substantiated when SABME is sent/received.
-- All link stations have circuits, but not all circuits
-- have link stations.
--
-- Key assumptions are:
-- (1) The MIB is designed to manage a single DLSw entity.
--
-- (2) A DLSw may support various types of transport connections.
-- - This DLSw MIB module does not restrict the possibility to
-- have, at any given moment, more than one "transport
-- connection" defined or active between two DLSw's.
-- - However, current DLSw architecture does not provide a mechanism,
-- e.g., DLSw host name, to prevent two transport connections of
-- different types between the same two DLSw's.
--
-- (3) This MIB assumes that interface MIB is implemented. ifIndex
-- is used in this MIB module.
--
-- (4) This MIB assumes that the SDLC MIB (or an equivalent enterprise
-- specific MIB) is implemented, since SDLC-specific objects
-- are not duplicated here.
--
-- (5) This MIB assumes that the LLC-2 MIB (or an equivalent enterprise
-- specific MIB) is implemented, since LLC-related objects are not
-- duplicated here.
--
-- (6) All MACs, SAPs, Ring numbers, ... are in non-canonical form.
-- That is, the most significant bit will be transmitted first.
--
-- *******************************************************************
DLSW-MIB DEFINITIONS ::= BEGIN
IMPORTS
DisplayString, RowStatus,
RowPointer, TruthValue,
TEXTUAL-CONVENTION FROM SNMPv2-TC
Chen, et. al. Standards Track [Page 13]
RFC 2024 DLSw MIB using SMIv2 October 1996
Counter32, Gauge32, TimeTicks,
OBJECT-TYPE, MODULE-IDENTITY,
NOTIFICATION-TYPE FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
ifIndex FROM IF-MIB
sdlcLSAddress FROM SNA-SDLC-MIB;
dlsw MODULE-IDENTITY
LAST-UPDATED "9606040900Z"
ORGANIZATION "AIW DLSw MIB RIGLET and IETF DLSw MIB Working Group"
CONTACT-INFO
"David D. Chen
IBM Corporation
800 Park, Highway 54
Research Triangle Park, NC 27709-9990
Tel: 1 919 254 6182
E-mail: dchen@vnet.ibm.com"
DESCRIPTION
"This MIB module contains objects to manage Data Link
Switches."
::= { mib-2 46 }
dlswMIB OBJECT IDENTIFIER ::= { dlsw 1 }
dlswDomains OBJECT IDENTIFIER ::= { dlsw 2 }
-- *******************************************************************
-- Textual convention definitions
-- *******************************************************************
NBName ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Represents a single qualified NetBIOS name, which can include
`don't care' and `wildcard' characters to represent a number
of real NetBIOS names. If an individual character position in
the qualified name contains a `?', the corresponding character
position in a real NetBIOS name is a `don't care'. If the
qualified name ends in `*', the remainder of a real NetBIOS
name is a `don't care'. `*' is only considered a wildcard if it
appears at the end of a name."
SYNTAX OCTET STRING (SIZE (0..16))
MacAddressNC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1x:"
STATUS current
DESCRIPTION
"Represents an 802 MAC address represented in
Chen, et. al. Standards Track [Page 14]
RFC 2024 DLSw MIB using SMIv2 October 1996
non-canonical format. That is, the most significant
bit will be transmitted first. If this information
is not available, the value is a zero length string."
SYNTAX OCTET STRING (SIZE (0 | 6))
TAddress ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Denotes a transport service address.
For dlswTCPDomain, a TAddress is 4 octets long,
containing the IP-address in network-byte order."
SYNTAX OCTET STRING (SIZE (0..255))
EndStationLocation ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Representing the location of an end station related
to the managed DLSw node."
SYNTAX INTEGER {
other (1),
internal (2), -- local virtual MAC address
remote (3), -- via DLSw partner
local (4) -- locally attached
}
DlcType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Representing the type of DLC of an end station, if
applicable."
SYNTAX INTEGER {
other (1), -- not assigned yet
na (2), -- not applicable
llc (3), -- 802.2 Logical Link Control
sdlc (4), -- SDLC
qllc (5) -- QLLC
}
LFSize ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The largest size of the INFO field (including DLC header,
not including any MAC-level or framing octets).
64 valid values as defined by the IEEE 802.1D
Addendum are acceptable."
SYNTAX INTEGER {
lfs516(516), lfs635(635), lfs754(754), lfs873(873),
lfs993(993), lfs1112(1112), lfs1231(1231),
Chen, et. al. Standards Track [Page 15]
RFC 2024 DLSw MIB using SMIv2 October 1996
lfs1350(1350), lfs1470(1470), lfs1542(1542),
lfs1615(1615), lfs1688(1688), lfs1761(1761),
lfs1833(1833), lfs1906(1906), lfs1979(1979),
lfs2052(2052), lfs2345(2345), lfs2638(2638),
lfs2932(2932), lfs3225(3225), lfs3518(3518),
lfs3812(3812), lfs4105(4105), lfs4399(4399),
lfs4865(4865), lfs5331(5331), lfs5798(5798),
lfs6264(6264), lfs6730(6730), lfs7197(7197),
lfs7663(7663), lfs8130(8130), lfs8539(8539),
lfs8949(8949), lfs9358(9358), lfs9768(9768),
lfs10178(10178), lfs10587(10587), lfs10997(10997),
lfs11407(11407), lfs12199(12199), lfs12992(12992),
lfs13785(13785), lfs14578(14578), lfs15370(15370),
lfs16163(16163), lfs16956(16956), lfs17749(17749),
lfs20730(20730), lfs23711(23711), lfs26693(26693),
lfs29674(29674), lfs32655(32655), lfs38618(38618),
lfs41600(41600), lfs44591(44591), lfs47583(47583),
lfs50575(50575), lfs53567(53567), lfs56559(56559),
lfs59551(59551), lfs65535(65535)
}
null OBJECT IDENTIFIER ::= { 0 0 }
-- *******************************************************************
-- DLSw Transport Domain definitions
-- *******************************************************************
-- DLSw over TCP
dlswTCPDomain OBJECT IDENTIFIER ::= { dlswDomains 1 }
-- for an IP address of length 4:
--
-- octets contents encoding
-- 1-4 IP-address network-byte order
--
DlswTCPAddress ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1d.1d.1d.1d"
STATUS current
DESCRIPTION
"Represents the IP address of a DLSw which uses
TCP as a transport protocol."
SYNTAX OCTET STRING (SIZE (4))
-- *******************************************************************
-- DLSw MIB Definition
-- *******************************************************************
Chen, et. al. Standards Track [Page 16]
RFC 2024 DLSw MIB using SMIv2 October 1996
-- The DLSw MIB module contains an object part and a conformance part.
-- Object part is organized in the following groups:
-- (1) dlswNode -- information about this DLSw
-- (2) dlswTConn -- about adjacent DLSw partners
-- (3) dlswInterface -- about which interfaces DLSw is active on
-- (4) dlswDirectory -- about any directory of local/remote resources
-- (5) dlswCircuit -- about established circuits.
-- (6) dlswSdlc -- about SDLC data link switched devices
dlswNode OBJECT IDENTIFIER ::= { dlswMIB 1 }
dlswTConn OBJECT IDENTIFIER ::= { dlswMIB 2 }
dlswInterface OBJECT IDENTIFIER ::= { dlswMIB 3 }
dlswDirectory OBJECT IDENTIFIER ::= { dlswMIB 4 }
dlswCircuit OBJECT IDENTIFIER ::= { dlswMIB 5 }
dlswSdlc OBJECT IDENTIFIER ::= { dlswMIB 6 } -- SDLC
-- *******************************************************************
-- THE NODE GROUP
-- *******************************************************************
-- -------------------------------------------------------------------
-- DLSw Node Identity
-- -------------------------------------------------------------------
dlswNodeVersion OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the particular version of the DLSw
standard supported by this DLSw. The first octet is a
hexadecimal value representing the DLSw standard Version
number of this DLSw, and the second is a hexadecimal value
representing the DLSw standard Release number. This
information is reported in DLSw Capabilities Exchange."
REFERENCE
"DLSW: Switch-to-Switch Protocol RFC 1795"
::= { dlswNode 1 }
dlswNodeVendorID OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (3))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the manufacturer's IEEE-assigned
organizationally Unique Identifier (OUI) of this DLSw.
This information is reported in DLSw Capabilities
Exchange."
REFERENCE
Chen, et. al. Standards Track [Page 17]
RFC 2024 DLSw MIB using SMIv2 October 1996
"DLSW: Switch-to-Switch Protocol RFC 1795"
::= { dlswNode 2 }
dlswNodeVersionString OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This string gives product-specific information about
this DLSw (e.g., product name, code release and fix level).
This flows in Capabilities Exchange messages."
REFERENCE
"DLSW: Switch-to-Switch Protocol RFC 1795"
::= { dlswNode 3 }
-- -------------------------------------------------------------------
-- DLSw Code Capability
-- -------------------------------------------------------------------
dlswNodeStdPacingSupport OBJECT-TYPE
SYNTAX INTEGER {
none (1), -- does not support DLSw
-- Standard pacing scheme
adaptiveRcvWindow (2), -- the receive window size
-- varies
fixedRcvWindow (3) -- the receive window size
-- remains constant
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Circuit pacing, as defined in the DLSw Standard, allows each
of the two DLSw nodes on a circuit to control the amount
of data the other is permitted to send to them. This object
reflects the level of support the DLSw node has for this
protocol. (1) means the node has no support for the standard
circuit pacing flows; it may use RFC 1434+ methods only, or
a proprietary flow control scheme. (2) means the node supports
the standard scheme and can vary the window sizes it grants as
a data receiver. (3) means the node supports the standard
scheme but never varies its receive window size."
::= { dlswNode 4 }
-- -------------------------------------------------------------------
-- DLSw Node Operational Objects
-- -------------------------------------------------------------------
dlswNodeStatus OBJECT-TYPE
SYNTAX INTEGER {
active (1),
Chen, et. al. Standards Track [Page 18]
RFC 2024 DLSw MIB using SMIv2 October 1996
inactive (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The status of the DLSw part of the system. Changing the
value from active to inactive causes DLSw to take
the following actions - (1) it disconnects all circuits
through all DLSw partners, (2) it disconnects all
transport connections to all DLSw partners, (3) it
disconnects all local DLC connections, and (4) it stops
processing all DLC connection set-up traffic.
Since these are destructive actions, the user should
query the circuit and transport connection tables in
advance to understand the effect this action will have.
Changing the value from inactive to active causes DLSw
to come up in its initial state, i.e., transport
connections established and ready to bring up circuits."
::= { dlswNode 5 }
dlswNodeUpTime OBJECT-TYPE
SYNTAX TimeTicks
UNITS "hundredths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time (in hundredths of a second) since
the DLSw portion of the system was last re-initialized.
That is, if dlswState is in the active state,
the time the dlswState entered the active state.
It will remain zero if dlswState is in the
inactive state."
::= { dlswNode 6 }
dlswNodeVirtualSegmentLFSize OBJECT-TYPE
SYNTAX LFSize
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The largest frame size (including DLC header and info field
but not any MAC-level or framing octets) this DLSw can forward
on any path through itself. This object can represent any box-
level frame size forwarding restriction (e.g., from the use
of fixed-size buffers). Some DLSw implementations will have
no such restriction.
This value will affect the LF size of circuits during circuit
creation. The LF size of an existing circuit can be found in
Chen, et. al. Standards Track [Page 19]
RFC 2024 DLSw MIB using SMIv2 October 1996
the RIF (Routing Information Field)."
DEFVAL { lfs65535 }
::= { dlswNode 7 }
-- ...................................................................
-- NETBIOS Resources
-- ...................................................................
dlswNodeResourceNBExclusivity OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of true indicates that the NetBIOS Names
configured in dlswDirNBTable are the only ones accessible
via this DLSw.
If a node supports sending run-time capabilities exchange
messages, changes to this object should cause that action.
It is up to the implementation exactly when to start the
run-time capabilities exchange."
::= { dlswNode 8 }
-- ...................................................................
-- MAC Address List
-- ...................................................................
dlswNodeResourceMacExclusivity OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of true indicates that the MAC addresses
configured in the dlswDirMacTable are the only ones
accessible via this DLSw.
If a node supports sending run-time capabilities exchange
messages, changes to this object should cause that action.
It is up to the implementation exactly when to start the
run-time capabilities exchange."
::= { dlswNode 9 }
-- *******************************************************************
-- TRANSPORT CONNECTION (aka: PARTNER DLSW)
-- *******************************************************************
-- -------------------------------------------------------------------
Chen, et. al. Standards Track [Page 20]
RFC 2024 DLSw MIB using SMIv2 October 1996
-- Transport Connection Statistics Objects
-- -------------------------------------------------------------------
dlswTConnStat OBJECT IDENTIFIER ::= { dlswTConn 1 }
dlswTConnStatActiveConnections OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of transport connections that are not in
`disconnected' state."
::= { dlswTConnStat 1 }
dlswTConnStatCloseIdles OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times transport connections in this node
exited the connected state with zero active circuits on
the transport connection."
::= { dlswTConnStat 2 }
dlswTConnStatCloseBusys OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times transport connections in this node
exited the connected state with some non-zero number
of active circuits on the transport connection. Normally
this means the transport connection failed unexpectedly."
::= { dlswTConnStat 3 }
-- -------------------------------------------------------------------
-- Transport Connection Configuration Table
-- -------------------------------------------------------------------
dlswTConnConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF DlswTConnConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table defines the transport connections
that will be initiated or accepted by this
DLSw. Structure of masks allows wildcard
definition for a collection of transport
connections by a conceptual row. For a
specific transport connection, there may
Chen, et. al. Standards Track [Page 21]
RFC 2024 DLSw MIB using SMIv2 October 1996
be multiple of conceptual rows match the
transport address. The `best' match will
the one to determine the characteristics
of the transport connection."
::= { dlswTConn 2 }
dlswTConnConfigEntry OBJECT-TYPE
SYNTAX DlswTConnConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each conceptual row defines a collection of
transport connections."
INDEX { dlswTConnConfigIndex }
::= { dlswTConnConfigTable 1 }
DlswTConnConfigEntry ::= SEQUENCE {
dlswTConnConfigIndex INTEGER,
dlswTConnConfigTDomain OBJECT IDENTIFIER,
dlswTConnConfigLocalTAddr TAddress,
dlswTConnConfigRemoteTAddr TAddress,
dlswTConnConfigLastModifyTime TimeTicks,
dlswTConnConfigEntryType INTEGER,
dlswTConnConfigGroupDefinition RowPointer,
dlswTConnConfigSetupType INTEGER,
dlswTConnConfigSapList OCTET STRING,
dlswTConnConfigAdvertiseMacNB TruthValue,
dlswTConnConfigInitCirRecvWndw INTEGER,
dlswTConnConfigOpens Counter32,
dlswTConnConfigRowStatus RowStatus
}
dlswTConnConfigIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index to the conceptual row of the table.
Negative numbers are not allowed. There
are objects defined that point to conceptual
rows of this table with this index value.
Zero is used to denote that no corresponding
row exists.
Index values are assigned by the agent, and
should not be reused but should continue to
increase in value."
::= { dlswTConnConfigEntry 1 }
Chen, et. al. Standards Track [Page 22]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswTConnConfigTDomain OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The object identifier which indicates the transport
domain of this conceptual row."
::= { dlswTConnConfigEntry 2 }
dlswTConnConfigLocalTAddr OBJECT-TYPE
SYNTAX TAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The local transport address for this conceptual row
of the transport connection definition."
::= { dlswTConnConfigEntry 3 }
dlswTConnConfigRemoteTAddr OBJECT-TYPE
SYNTAX TAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The remote transport address. Together with
dlswTConnConfigEntryType and dlswTConnConfigGroupDefinition,
the object instance of this conceptual row identifies a
collection of the transport connections that will be
either initiated by this DLSw or initiated by a partner
DLSw and accepted by this DLSw."
::= { dlswTConnConfigEntry 4 }
dlswTConnConfigLastModifyTime OBJECT-TYPE
SYNTAX TimeTicks
UNITS "hundredths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time (in hundredths of a second) since the value of
any object in this conceptual row except for
dlswTConnConfigOpens was last changed. This value
may be compared to dlswTConnOperConnectTime to
determine whether values in this row are completely
valid for a transport connection created using
this row definition."
::= { dlswTConnConfigEntry 5 }
dlswTConnConfigEntryType OBJECT-TYPE
SYNTAX INTEGER {
Chen, et. al. Standards Track [Page 23]
RFC 2024 DLSw MIB using SMIv2 October 1996
individual (1),
global (2),
group (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The object instance signifies the type of entry in the
associated conceptual row. The value of `individual'
means that the entry applies to a specific partner DLSw
node as identified by dlswTConnConfigRemoteTAddr and
dlswTConnConfigTDomain. The value of `global'
means that the entry applies to all partner DLSw nodes
of the TDomain. The value of 'group' means that the entry
applies to a specific set of DLSw nodes in the TDomain.
Any group definitions are enterprise-specific and are pointed
to by dlswTConnConfigGroupDefinition. In the cases of
`global' and `group', the value in dlswTConnConfigRemoteTAddr
may not have any significance."
::= { dlswTConnConfigEntry 6 }
dlswTConnConfigGroupDefinition OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For conceptual rows of `individual' and `global' as
specified in dlswTConnConfigEntryType, the instance
of this object is `0.0'. For conceptual rows of
`group', the instance points to the specific
group definition."
::= { dlswTConnConfigEntry 7 }
dlswTConnConfigSetupType OBJECT-TYPE
SYNTAX INTEGER {
other (1),
activePersistent (2),
activeOnDemand (3),
passive (4),
excluded (5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value of the instance of a conceptual row
identifies the behavior of the collection of
transport connections that this conceptual row
Chen, et. al. Standards Track [Page 24]
RFC 2024 DLSw MIB using SMIv2 October 1996
defines. The value of activePersistent, activeOnDemand
and passive means this DLSw will accept any transport
connections, initiated by partner DLSw nodes, which
are defined by this conceptual row. The value of
activePersistent means this DLSw will also initiate
the transport connections of this conceptual row and
retry periodically if necessary. The value of
activeOnDemand means this DLSw will initiate a
transport connection of this conceptual row, if
there is a directory cache hits. The value of
other is implementation specific. The value of exclude
means that the specified node is not allowed to be
a partner to this DLSw node. To take a certain
conceptual row definition out of service, a value of
notInService for dlswTConnConfigRowStatus should be
used."
DEFVAL { passive }
::= { dlswTConnConfigEntry 8 }
dlswTConnConfigSapList OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(16))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SAP list indicates which SAPs are advertised to
the transport connection defined by this conceptual
row. Only SAPs with even numbers are represented,
in the form of the most significant bit of the first
octet representing the SAP 0, the next most significant
bit representing the SAP 2, to the least significant
bit of the last octet representing the SAP 254. Data
link switching is allowed for those SAPs which have
one in its corresponding bit, not allowed otherwise.
The whole SAP list has to be changed together. Changing
the SAP list affects only new circuit establishments
and has no effect on established circuits.
This list can be used to restrict specific partners
from knowing about all the SAPs used by DLSw on all its
interfaces (these are represented in dlswIfSapList for
each interface). For instance, one may want to run NetBIOS
with some partners but not others.
If a node supports sending run-time capabilities exchange
messages, changes to this object should cause that action.
When to start the run-time capabilities exchange is
implementation-specific.
Chen, et. al. Standards Track [Page 25]
RFC 2024 DLSw MIB using SMIv2 October 1996
The DEFVAL below indicates support for SAPs 0, 4, 8, and C."
DEFVAL { 'AA000000000000000000000000000000'H }
::= { dlswTConnConfigEntry 9 }
dlswTConnConfigAdvertiseMacNB OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of true indicates that any defined local MAC
addresses and NetBIOS names will be advertised to a
partner node via initial and (if supported) run-time
capabilities exchange messages. The DLSw node should send
the appropriate exclusivity control vector to accompany
each list it sends, or to represent that the node is
explicitly configured to have a null list.
The value of false indicates that the DLSw node should not
send a MAC address list or NetBIOS name list, and should
also not send their corresponding exclusivity control
vectors."
DEFVAL { true }
::= { dlswTConnConfigEntry 10 }
dlswTConnConfigInitCirRecvWndw OBJECT-TYPE
SYNTAX INTEGER (0..65535)
UNITS "SSP messages"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The initial circuit receive pacing window size, in the unit
of SSP messages, to be used for future transport connections
activated using this table row. The managed node sends this
value as its initial receive pacing window in its initial
capabilities exchange message. Changing this value does not
affect the initial circuit receive pacing window size of
currently active transport connections. If the standard window
pacing scheme is not supported, the value is zero.
A larger receive window value may be appropriate for partners
that are reachable only via physical paths that have longer
network delays."
DEFVAL { 1 }
::= { dlswTConnConfigEntry 11 }
dlswTConnConfigOpens OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
Chen, et. al. Standards Track [Page 26]
RFC 2024 DLSw MIB using SMIv2 October 1996
STATUS current
DESCRIPTION
"Number of times transport connections entered
connected state according to the definition of
this conceptual row."
::= { dlswTConnConfigEntry 12 }
dlswTConnConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used by the manager to create
or delete the row entry in the dlswTConnConfigTable
following the RowStatus textual convention. The value
of notInService will be used to take a conceptual
row definition out of use."
::= { dlswTConnConfigEntry 13 }
-- -------------------------------------------------------------------
-- Transport Connection Operation Table
-- -------------------------------------------------------------------
-- (1) At most one transport connection can be connected between
-- this DLSw and one of its DLSw partners at a given time.
-- (2) Multiple transport types are supported.
-- (3) Since the entries may be reused, dlswTConnOperEntryTime
-- needs to be consulted for the possibility of counter reset.
-- -------------------------------------------------------------------
dlswTConnOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF DlswTConnOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of transport connections. It is optional but
desirable for the agent to keep an entry for some
period of time after the transport connection is
disconnected. This allows the manager to capture
additional useful information about the connection, in
particular, statistical information and the cause of the
disconnection."
::= { dlswTConn 3 }
dlswTConnOperEntry OBJECT-TYPE
SYNTAX DlswTConnOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Chen, et. al. Standards Track [Page 27]
RFC 2024 DLSw MIB using SMIv2 October 1996
""
INDEX { dlswTConnOperTDomain, dlswTConnOperRemoteTAddr }
::= { dlswTConnOperTable 1 }
DlswTConnOperEntry ::= SEQUENCE {
dlswTConnOperTDomain OBJECT IDENTIFIER,
dlswTConnOperLocalTAddr TAddress,
dlswTConnOperRemoteTAddr TAddress,
dlswTConnOperEntryTime TimeTicks,
dlswTConnOperConnectTime TimeTicks,
dlswTConnOperState INTEGER,
dlswTConnOperConfigIndex INTEGER,
dlswTConnOperFlowCntlMode INTEGER,
dlswTConnOperPartnerVersion OCTET STRING,
dlswTConnOperPartnerVendorID OCTET STRING,
dlswTConnOperPartnerVersionStr DisplayString,
dlswTConnOperPartnerInitPacingWndw INTEGER,
dlswTConnOperPartnerSapList OCTET STRING,
dlswTConnOperPartnerNBExcl TruthValue,
dlswTConnOperPartnerMacExcl TruthValue,
dlswTConnOperPartnerNBInfo INTEGER,
dlswTConnOperPartnerMacInfo INTEGER,
dlswTConnOperDiscTime TimeTicks,
dlswTConnOperDiscReason INTEGER,
dlswTConnOperDiscActiveCir INTEGER,
dlswTConnOperInDataPkts Counter32,
dlswTConnOperOutDataPkts Counter32,
dlswTConnOperInDataOctets Counter32,
dlswTConnOperOutDataOctets Counter32,
dlswTConnOperInCntlPkts Counter32,
dlswTConnOperOutCntlPkts Counter32,
dlswTConnOperCURexSents Counter32,
dlswTConnOperICRexRcvds Counter32,
dlswTConnOperCURexRcvds Counter32,
dlswTConnOperICRexSents Counter32,
dlswTConnOperNQexSents Counter32,
dlswTConnOperNRexRcvds Counter32,
dlswTConnOperNQexRcvds Counter32,
dlswTConnOperNRexSents Counter32,
Chen, et. al. Standards Track [Page 28]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswTConnOperCirCreates Counter32,
dlswTConnOperCircuits Gauge32
}
dlswTConnOperTDomain OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The object identifier indicates the transport domain
of this transport connection."
::= { dlswTConnOperEntry 1 }
dlswTConnOperLocalTAddr OBJECT-TYPE
SYNTAX TAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local transport address for this transport connection.
This value could be different from dlswTConnConfigLocalAddr,
if the value of the latter were changed after this transport
connection was established."
::= { dlswTConnOperEntry 2 }
dlswTConnOperRemoteTAddr OBJECT-TYPE
SYNTAX TAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The remote transport address of this transport connection."
::= { dlswTConnOperEntry 3 }
dlswTConnOperEntryTime OBJECT-TYPE
SYNTAX TimeTicks
UNITS "hundredths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time (in hundredths of a second) since this
transport connection conceptual row was created."
::= { dlswTConnOperEntry 4 }
-- ...................................................................
-- DLSw Transport Connection Operational Objects
-- ...................................................................
dlswTConnOperConnectTime OBJECT-TYPE
SYNTAX TimeTicks
Chen, et. al. Standards Track [Page 29]
RFC 2024 DLSw MIB using SMIv2 October 1996
UNITS "hundredths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time (in hundredths of a second) since this
transport connection last entered the 'connected' state.
A value of zero means this transport connection has never
been established."
::= { dlswTConnOperEntry 5 }
dlswTConnOperState OBJECT-TYPE
SYNTAX INTEGER {
connecting (1),
initCapExchange (2),
connected (3),
quiescing (4),
disconnecting (5),
disconnected (6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The state of this transport connection. The transport
connection enters `connecting' state when DLSw makes
a connection request to the transport layer. Once initial
Capabilities Exchange is sent, the transport connection
enters enters `initCapExchange' state. When partner
capabilities have been determined and the transport
connection is ready for sending CanUReach (CUR) messages,
it moves to the `connected' state. When DLSw is in the
process of bringing down the connection, it is in the
`disconnecting' state. When the transport layer
indicates one of its connections is disconnected, the
transport connection moves to the `disconnected' state.
Whereas all of the values will be returned in response
to a management protocol retrieval operation, only two
values may be specified in a management protocol set
operation: `quiescing' and `disconnecting'. Changing
the value to `quiescing' prevents new circuits from being
established, and will cause a transport disconnect when
the last circuit on the connection goes away. Changing
the value to `disconnecting' will force off all circuits
immediately and bring the connection to `disconnected'
state."
::= { dlswTConnOperEntry 6 }
dlswTConnOperConfigIndex OBJECT-TYPE
Chen, et. al. Standards Track [Page 30]
RFC 2024 DLSw MIB using SMIv2 October 1996
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of dlswTConnConfigIndex of the dlswTConnConfigEntry
that governs the configuration information used by this
dlswTConnOperEntry. The manager can therefore normally
examine both configured and operational information
for this transport connection.
This value is zero if the corresponding dlswTConnConfigEntry
was deleted after the creation of this dlswTConnOperEntry.
If some fields in the former were changed but the conceptual
row was not deleted, some configuration information may not
be valid for this operational transport connection. The
manager can compare dlswTConnOperConnectTime and
dlswTConnConfigLastModifyTime to determine if this condition
exists."
::= { dlswTConnOperEntry 7 }
-- ...................................................................
-- Transport Connection Characteristics
-- ...................................................................
dlswTConnOperFlowCntlMode OBJECT-TYPE
SYNTAX INTEGER {
undetermined (1),
pacing (2), -- DLSw standard flow control
other (3) -- non-DLSw standard flow control
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The flow control mechanism in use on this transport connection.
This value is undetermined (1) before the mode of flow control
can be established on a new transport connection (i.e., after
CapEx is sent but before Capex or other SSP control messages
have been received). Pacing (2) indicates that the standard
RFC 1795 pacing mechanism is in use. Other (3) may be either
the RFC 1434+ xBusy mechanism operating to a back-level DLSw,
or a vendor-specific flow control method. Whether it is xBusy
or not can be inferred from dlswTConnOperPartnerVersion."
::= { dlswTConnOperEntry 8 }
-- ...................................................................
dlswTConnOperPartnerVersion OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0 | 2))
Chen, et. al. Standards Track [Page 31]
RFC 2024 DLSw MIB using SMIv2 October 1996
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies which version (first octet) and release
(second octet) of the DLSw standard is supported by this
partner DLSw. This information is obtained from a DLSw
capabilities exchange message received from the partner DLSw.
A string of zero length is returned before a Capabilities
Exchange message is received, or if one is never received.
A conceptual row with a dlswTConnOperState of `connected' but
a zero length partner version indicates that the partner is
a non-standard DLSw partner.
If an implementation chooses to keep dlswTConnOperEntrys in
the `disconnected' state, this value should remain unchanged."
REFERENCE
"DLSW: Switch-to-Switch Protocol RFC 1795"
::= { dlswTConnOperEntry 9 }
dlswTConnOperPartnerVendorID OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0 | 3))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the IEEE-assigned organizationally
Unique Identifier (OUI) of the maker of this partner
DLSw. This information is obtained from a DLSw
capabilities exchange message received from the partner DLSw.
A string of zero length is returned before a Capabilities
Exchange message is received, or if one is never received.
If an implementation chooses to keep dlswTConnOperEntrys in
the `disconnected' state, this value should remain unchanged."
::= { dlswTConnOperEntry 10 }
dlswTConnOperPartnerVersionStr OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..253))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the particular product version (e.g.,
product name, code level, fix level) of this partner DLSw.
The format of the actual version string is vendor-specific.
This information is obtained from a DLSw capabilities exchange
message received from the partner DLSw.
A string of zero length is returned before a Capabilities
Exchange message is received, if one is never received, or
if one is received but it does not contain a version string.
Chen, et. al. Standards Track [Page 32]
RFC 2024 DLSw MIB using SMIv2 October 1996
If an implementation chooses to keep dlswTConnOperEntrys in
the `disconnected' state, this value should remain unchanged."
REFERENCE
"DLSW: Switch-to-Switch Protocol RFC 1795"
::= { dlswTConnOperEntry 11 }
dlswTConnOperPartnerInitPacingWndw OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the partner initial receive pacing window. This
is our initial send pacing window for all new circuits on this
transport connection, as modified and granted by the first flow
control indication the partner sends on each circuit.
This information is obtained from a DLSw capabilities exchange
message received from the partner DLSw.
A value of zero is returned before a Capabilities
Exchange message is received, or if one is never received.
If an implementation chooses to keep dlswTConnOperEntrys in
the `disconnected' state, this value should remain unchanged."
REFERENCE
"DLSW: Switch-to-Switch Protocol RFC 1795"
::= { dlswTConnOperEntry 12 }
-- ...................................................................
dlswTConnOperPartnerSapList OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0 | 16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Supported SAP List received in the capabilities
exchange message from the partner DLSw. This list has
the same format described for dlswTConnConfigSapList.
A string of zero length is returned before a Capabilities
Exchange message is received, or if one is never received.
If an implementation chooses to keep dlswTConnOperEntrys in
the `disconnected' state, this value should remain unchanged."
::= { dlswTConnOperEntry 13 }
dlswTConnOperPartnerNBExcl OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Chen, et. al. Standards Track [Page 33]
RFC 2024 DLSw MIB using SMIv2 October 1996
"The value of true signifies that the NetBIOS names received
from this partner in the NetBIOS name list in its capabilities
exchange message are the only NetBIOS names reachable by
that partner. `False' indicates that other NetBIOS names may
be reachable. `False' should be returned before a Capabilities
Exchange message is received, if one is never received, or if
one is received without a NB Name Exclusivity CV.
If an implementation chooses to keep dlswTConnOperEntrys in
the `disconnected' state, this value should remain unchanged."
::= { dlswTConnOperEntry 14 }
dlswTConnOperPartnerMacExcl OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of true signifies that the MAC addresses received
from this partner in the MAC address list in its capabilities
exchange message are the only MAC addresses reachable by
that partner. `False' indicates that other MAC addresses may
be reachable. `False' should be returned before a Capabilities
Exchange message is received, if one is never received, or if
one is received without a MAC Address Exclusivity CV.
If an implementation chooses to keep dlswTConnOperEntrys in
the `disconnected' state, this value should remain unchanged."
::= { dlswTConnOperEntry 15 }
dlswTConnOperPartnerNBInfo OBJECT-TYPE
SYNTAX INTEGER {
none (1), -- none is kept
partial (2), -- partial list is kept
complete (3), -- complete list is kept
notApplicable (4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"It is up to this DSLw whether to keep either none, some,
or all of the NetBIOS name list that was received in
the capabilities exchange message sent by this partner DLSw.
This object identifies how much information was kept by
this DLSw. These names are stored as userConfigured
remote entries in dlswDirNBTable.
A value of (4), notApplicable, should be returned before
a Capabilities Exchange message is received, or if one is
never received.
Chen, et. al. Standards Track [Page 34]
RFC 2024 DLSw MIB using SMIv2 October 1996
If an implementation chooses to keep dlswTConnOperEntrys in
the `disconnected' state, this value should remain unchanged."
::= { dlswTConnOperEntry 16 }
dlswTConnOperPartnerMacInfo OBJECT-TYPE
SYNTAX INTEGER {
none (1), -- none is kept
partial (2), -- partial list is kept
complete (3), -- complete list is kept
notApplicable (4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"It is up to this DLSw whether to keep either none, some,
or all of the MAC address list that was received in the
capabilities exchange message sent by this partner DLSw.
This object identifies how much information was kept by
this DLSw. These names are stored as userConfigured
remote entries in dlswDirMACTable.
A value of (4), notApplicable, should be returned before
a Capabilities Exchange message is received, or if one is
never received.
If an implementation chooses to keep dlswTConnOperEntrys in
the `disconnected' state, this value should remain unchanged."
::= { dlswTConnOperEntry 17 }
-- ...................................................................
-- Information about the last disconnect of this transport connection.
-- These objects make sense only for implementations that keep
-- transport connection information around after disconnection.
-- ...................................................................
dlswTConnOperDiscTime OBJECT-TYPE
SYNTAX TimeTicks
UNITS "hundredths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time (in hundredths of a second) since the
dlswTConnOperState last entered `disconnected' state."
::= { dlswTConnOperEntry 18 }
dlswTConnOperDiscReason OBJECT-TYPE
SYNTAX INTEGER {
other (1),
capExFailed (2),
transportLayerDisc (3),
Chen, et. al. Standards Track [Page 35]
RFC 2024 DLSw MIB using SMIv2 October 1996
operatorCommand (4),
lastCircuitDiscd (5),
protocolError (6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object signifies the reason that either prevented the
transport connection from entering the connected state, or
caused the transport connection to enter the disconnected
state."
::= { dlswTConnOperEntry 19 }
dlswTConnOperDiscActiveCir OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of circuits active (not in DISCONNECTED state)
at the time the transport connection was last disconnected.
This value is zero if the transport connection has never
been connected."
::= { dlswTConnOperEntry 20 }
-- ...................................................................
-- Transport Connection Statistics
-- (1) Traffic counts
-- ...................................................................
dlswTConnOperInDataPkts OBJECT-TYPE
SYNTAX Counter32
UNITS "SSP messages"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Switch-to-Switch Protocol (SSP) messages of
type DGRMFRAME, DATAFRAME, or INFOFRAME received on this
transport connection."
::= { dlswTConnOperEntry 21 }
dlswTConnOperOutDataPkts OBJECT-TYPE
SYNTAX Counter32
UNITS "SSP messages"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Switch-to-Switch Protocol (SSP) messages of
type DGRMFRAME, DATAFRAME, or INFOFRAME transmitted on this
transport connection."
Chen, et. al. Standards Track [Page 36]
RFC 2024 DLSw MIB using SMIv2 October 1996
::= { dlswTConnOperEntry 22 }
dlswTConnOperInDataOctets OBJECT-TYPE
SYNTAX Counter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number octets in Switch-to-Switch Protocol (SSP) messages
of type DGRMFRAME, DATAFRAME, or INFOFRAME received on this
transport connection. Each message is counted starting with
the first octet following the SSP message header."
::= { dlswTConnOperEntry 23 }
dlswTConnOperOutDataOctets OBJECT-TYPE
SYNTAX Counter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number octets in Switch-to-Switch Protocol (SSP) messages
of type DGRMFRAME, DATAFRAME, or INFOFRAME transmitted on this
transport connection. Each message is counted starting with
the first octet following the SSP message header."
::= { dlswTConnOperEntry 24 }
dlswTConnOperInCntlPkts OBJECT-TYPE
SYNTAX Counter32
UNITS "SSP messages"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Switch-to-Switch Protocol (SSP) messages
received on this transport connection which were not of
type DGRMFRAME, DATAFRAME, or INFOFRAME."
::= { dlswTConnOperEntry 25 }
dlswTConnOperOutCntlPkts OBJECT-TYPE
SYNTAX Counter32
UNITS "SSP messages"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Switch-to-Switch Protocol (SSP) messages of
transmitted on this transport connection which were not of
type DGRMFRAME, DATAFRAME, or INFOFRAME."
::= { dlswTConnOperEntry 26 }
Chen, et. al. Standards Track [Page 37]
RFC 2024 DLSw MIB using SMIv2 October 1996
-- ...................................................................
-- (2) Directory activities (Explorer messages)
-- ...................................................................
dlswTConnOperCURexSents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of CanUReach_ex messages sent on this transport
connection."
::= { dlswTConnOperEntry 27 }
dlswTConnOperICRexRcvds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of ICanReach_ex messages received on this transport
connection."
::= { dlswTConnOperEntry 28 }
dlswTConnOperCURexRcvds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of CanUReach_ex messages received on this transport
connection."
::= { dlswTConnOperEntry 29 }
dlswTConnOperICRexSents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of ICanReach_ex messages sent on this transport
connection."
::= { dlswTConnOperEntry 30 }
-- ...................................................................
dlswTConnOperNQexSents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NetBIOS_NQ_ex (NetBIOS Name Query-explorer)
Chen, et. al. Standards Track [Page 38]
RFC 2024 DLSw MIB using SMIv2 October 1996
messages sent on this transport connection."
::= { dlswTConnOperEntry 31 }
dlswTConnOperNRexRcvds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NETBIOS_NR_ex (NetBIOS Name Recognized-explorer)
messages received on this transport connection."
::= { dlswTConnOperEntry 32 }
dlswTConnOperNQexRcvds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NETBIOS_NQ_ex messages received on this
transport connection."
::= { dlswTConnOperEntry 33 }
dlswTConnOperNRexSents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NETBIOS_NR_ex messages sent on this transport
connection."
::= { dlswTConnOperEntry 34 }
-- ...................................................................
-- (3) Circuit activities on each transport connection
-- ...................................................................
dlswTConnOperCirCreates OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that circuits entered `circuit_established'
state (not counting transitions from `circuit_restart')."
::= { dlswTConnOperEntry 35 }
dlswTConnOperCircuits OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of currently active circuits on this transport
Chen, et. al. Standards Track [Page 39]
RFC 2024 DLSw MIB using SMIv2 October 1996
connection, where `active' means not in `disconnected' state."
::= { dlswTConnOperEntry 36 }
-- -------------------------------------------------------------------
-- Transport Connection Specific
-- -------------------------------------------------------------------
dlswTConnSpecific OBJECT IDENTIFIER ::= { dlswTConn 4 }
dlswTConnTcp OBJECT IDENTIFIER ::= { dlswTConnSpecific 1 }
-- ...................................................................
-- TCP Transport Connection Specific -- Configuration
-- ...................................................................
dlswTConnTcpConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF DlswTConnTcpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table defines the TCP transport connections that
will be either initiated by or accepted by this DSLw.
It augments the entries in dlswTConnConfigTable whose domain
is dlswTCPDomain."
::= { dlswTConnTcp 1 }
dlswTConnTcpConfigEntry OBJECT-TYPE
SYNTAX DlswTConnTcpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each conceptual row defines parameters that are
specific to dlswTCPDomain transport connections."
INDEX { dlswTConnConfigIndex }
::= { dlswTConnTcpConfigTable 1 }
DlswTConnTcpConfigEntry ::= SEQUENCE {
dlswTConnTcpConfigKeepAliveInt INTEGER,
dlswTConnTcpConfigTcpConnections INTEGER,
dlswTConnTcpConfigMaxSegmentSize INTEGER
}
dlswTConnTcpConfigKeepAliveInt OBJECT-TYPE
SYNTAX INTEGER (0..1800)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The time in seconds between TCP keepAlive messages when
no traffic is flowing. Zero signifies no keepAlive protocol.
Chen, et. al. Standards Track [Page 40]
RFC 2024 DLSw MIB using SMIv2 October 1996
Changes take effect only for new TCP connections."
DEFVAL { 0 }
::= { dlswTConnTcpConfigEntry 1 }
dlswTConnTcpConfigTcpConnections OBJECT-TYPE
SYNTAX INTEGER (1..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is our preferred number of TCP connections within a
TCP transport connection. The actual number used is negotiated
at capabilities exchange time. Changes take effect only
for new transport connections."
DEFVAL { 2 }
::= { dlswTConnTcpConfigEntry 2 }
dlswTConnTcpConfigMaxSegmentSize OBJECT-TYPE
SYNTAX INTEGER (0..65535)
UNITS "packets"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is the number of bytes that this node is
willing to receive over the read TCP connection(s).
Changes take effect for new transport connections."
DEFVAL { 4096 }
::= { dlswTConnTcpConfigEntry 3 }
-- ...................................................................
-- TCP Transport Connection Specific -- Operation
-- ...................................................................
dlswTConnTcpOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF DlswTConnTcpOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of TCP transport connections. It is optional
but desirable for the agent to keep an entry for some
period of time after the transport connection is
disconnected. This allows the manager to capture
additional useful information about the connection, in
particular, statistical information and the cause of the
disconnection."
::= { dlswTConnTcp 2 }
dlswTConnTcpOperEntry OBJECT-TYPE
SYNTAX DlswTConnTcpOperEntry
Chen, et. al. Standards Track [Page 41]
RFC 2024 DLSw MIB using SMIv2 October 1996
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
""
INDEX { dlswTConnOperTDomain, dlswTConnOperRemoteTAddr }
::= { dlswTConnTcpOperTable 1 }
DlswTConnTcpOperEntry ::= SEQUENCE {
dlswTConnTcpOperKeepAliveInt INTEGER,
dlswTConnTcpOperPrefTcpConnections INTEGER,
dlswTConnTcpOperTcpConnections INTEGER
}
dlswTConnTcpOperKeepAliveInt OBJECT-TYPE
SYNTAX INTEGER (0..1800)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time in seconds between TCP keepAlive messages when
no traffic is flowing. Zero signifies no keepAlive protocol is
operating."
::= { dlswTConnTcpOperEntry 1 }
dlswTConnTcpOperPrefTcpConnections OBJECT-TYPE
SYNTAX INTEGER (1..16)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the number of TCP connections preferred by this DLSw
partner, as received in its capabilities exchange message."
::= { dlswTConnTcpOperEntry 2 }
dlswTConnTcpOperTcpConnections OBJECT-TYPE
SYNTAX INTEGER (1..16)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the actual current number of TCP connections within
this transport connection."
::= { dlswTConnTcpOperEntry 3 }
-- *******************************************************************
-- DLSW INTERFACE GROUP
-- *******************************************************************
dlswIfTable OBJECT-TYPE
Chen, et. al. Standards Track [Page 42]
RFC 2024 DLSw MIB using SMIv2 October 1996
SYNTAX SEQUENCE OF DlswIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The list of interfaces on which DLSw is active."
::= { dlswInterface 1 }
dlswIfEntry OBJECT-TYPE
SYNTAX DlswIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
""
INDEX { ifIndex }
::= { dlswIfTable 1 }
DlswIfEntry ::= SEQUENCE {
dlswIfRowStatus RowStatus,
dlswIfVirtualSegment INTEGER,
dlswIfSapList OCTET STRING
}
dlswIfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used by the manager to create
or delete the row entry in the dlswIfTable
following the RowStatus textual convention."
::= { dlswIfEntry 1 }
dlswIfVirtualSegment OBJECT-TYPE
SYNTAX INTEGER (0..4095 | 65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The segment number that uniquely identifies the virtual
segment to which this DLSw interface is connected.
Current source routing protocols limit this value to
the range 0 - 4095. (The value 0 is used by some
management applications for special test cases.)
A value of 65535 signifies that no virtual segment
is assigned to this interface. For instance,
in a non-source routing environment, segment number
assignment is not required."
DEFVAL { 65535 }
::= { dlswIfEntry 2 }
Chen, et. al. Standards Track [Page 43]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswIfSapList OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(16))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SAP list indicates which SAPs are allowed to be
data link switched through this interface. This list
has the same format described for dlswTConnConfigSapList.
When changes to this object take effect is implementation-
specific. Turning off a particular SAP can destroy
active circuits that are using that SAP. An agent
implementation may reject such changes until there are no
active circuits if it so chooses. In this case, it is up
to the manager to close the circuits first, using
dlswCircuitState.
The DEFVAL below indicates support for SAPs 0, 4, 8, and C."
DEFVAL { 'AA000000000000000000000000000000'H }
::= { dlswIfEntry 3 }
-- *******************************************************************
-- DIRECTORY
-- Directory services caches the locations of MAC addresses
-- and NetBIOS names. For resources which are attached via
-- local interfaces, the ifIndex may be cached, and for
-- resources which are reachable via a DLSw partner, the
-- transport address of the DLSw partner is cached.
-- *******************************************************************
-- -------------------------------------------------------------------
-- Directory Related Statistical Objects
-- -------------------------------------------------------------------
dlswDirStat OBJECT IDENTIFIER ::= { dlswDirectory 1 }
dlswDirMacEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current total number of entries in the dlswDirMacTable."
::= { dlswDirStat 1 }
dlswDirMacCacheHits OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Chen, et. al. Standards Track [Page 44]
RFC 2024 DLSw MIB using SMIv2 October 1996
DESCRIPTION
"The number of times a cache search for a particular MAC address
resulted in success."
::= { dlswDirStat 2 }
dlswDirMacCacheMisses OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a cache search for a particular MAC address
resulted in failure."
::= { dlswDirStat 3 }
dlswDirMacCacheNextIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The next value of dlswDirMacIndex to be assigned by
the agent. A retrieval of this object atomically reserves
the returned value for use by the manager to create a row
in dlswDirMacTable. This makes it possible for the agent
to control the index space of the MAC address cache, yet
allows the manager to administratively create new rows."
::= { dlswDirStat 4 }
dlswDirNBEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current total number of entries in the dlswDirNBTable."
::= { dlswDirStat 5 }
dlswDirNBCacheHits OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a cache search for a particular NetBIOS
name resulted in success."
::= { dlswDirStat 6 }
dlswDirNBCacheMisses OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Chen, et. al. Standards Track [Page 45]
RFC 2024 DLSw MIB using SMIv2 October 1996
DESCRIPTION
"The number of times a cache search for a particular NetBIOS
name resulted in failure."
::= { dlswDirStat 7 }
dlswDirNBCacheNextIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The next value of dlswDirNBIndex to be assigned by the
agent. A retrieval of this object atomically reserves
the returned value for use by the manager to create
a row in dlswDirNBTable. This makes it possible for the
agent to control the index space for the NetBIOS name
cache, yet allows the manager to administratively
create new rows."
::= { dlswDirStat 8 }
-- -------------------------------------------------------------------
-- Directory Cache
-- -------------------------------------------------------------------
dlswDirCache OBJECT IDENTIFIER ::= { dlswDirectory 2 }
-- ...................................................................
-- Directory for MAC Addresses.
-- All Possible combinations of values of these objects.
--
-- EntryType LocationType Location Status
-- -------------- ------------ ------------------ --------------
-- userConfigured local ifEntry or 0.0 reachable, or
-- notReachable, or
-- unknown
-- userConfigured remote TConnConfigEntry reachable, or
-- notReachable, or
-- unknown
-- partnerCapExMsg remote TConnOperEntry unknown
-- dynamic local ifEntry or 0.0 reachable
-- dynamic remote TConnOperEntry reachable
--
-- ...................................................................
dlswDirMacTable OBJECT-TYPE
SYNTAX SEQUENCE OF DlswDirMacEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains locations of MAC addresses.
They could be either verified or not verified,
Chen, et. al. Standards Track [Page 46]
RFC 2024 DLSw MIB using SMIv2 October 1996
local or remote, and configured locally or learned
from either Capabilities Exchange messages or
directory searches."
::= { dlswDirCache 1 }
dlswDirMacEntry OBJECT-TYPE
SYNTAX DlswDirMacEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indexed by dlswDirMacIndex."
INDEX { dlswDirMacIndex }
::= { dlswDirMacTable 1 }
DlswDirMacEntry ::= SEQUENCE {
dlswDirMacIndex INTEGER,
dlswDirMacMac MacAddressNC,
dlswDirMacMask MacAddressNC,
dlswDirMacEntryType INTEGER,
dlswDirMacLocationType INTEGER,
dlswDirMacLocation RowPointer,
dlswDirMacStatus INTEGER,
dlswDirMacLFSize LFSize,
dlswDirMacRowStatus RowStatus
}
dlswDirMacIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies a conceptual row of this table."
::= { dlswDirMacEntry 1 }
dlswDirMacMac OBJECT-TYPE
SYNTAX MacAddressNC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The MAC address, together with the dlswDirMacMask,
specifies a set of MAC addresses that are defined or
discovered through an interface or partner DLSw nodes."
::= { dlswDirMacEntry 2 }
dlswDirMacMask OBJECT-TYPE
SYNTAX MacAddressNC
MAX-ACCESS read-create
STATUS current
Chen, et. al. Standards Track [Page 47]
RFC 2024 DLSw MIB using SMIv2 October 1996
DESCRIPTION
"The MAC address mask, together with the dlswDirMacMac,
specifies a set of MAC addresses that are defined or
discovered through an interface or partner DLSw nodes."
DEFVAL { 'FFFFFFFFFFFF'H }
::= { dlswDirMacEntry 3 }
dlswDirMacEntryType OBJECT-TYPE
SYNTAX INTEGER {
other (1),
userConfiguredPublic (2),
userConfiguredPrivate (3),
partnerCapExMsg (4),
dynamic (5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The cause of the creation of this conceptual row.
It could be one of the three methods: (1) user
configured, including via management protocol
set operations, configuration file, command line
or equivalent methods; (2) learned from the
partner DLSw Capabilities Exchange messages;
and (3) dynamic, e.g., learned from ICanReach
messages, or LAN explorer frames. Since only
individual MAC addresses can be dynamically learned,
dynamic entries will all have a mask of all FFs.
The public versus private distinction for user-
configured resources applies only to local resources
(UC remote resources are private), and indicates
whether that resource should be advertised in
capabilities exchange messages sent by this node."
DEFVAL { userConfiguredPublic }
::= { dlswDirMacEntry 4 }
dlswDirMacLocationType OBJECT-TYPE
SYNTAX INTEGER {
other (1),
local (2),
remote (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The location of the resource (or a collection of
resources using a mask) of this conceptual row
Chen, et. al. Standards Track [Page 48]
RFC 2024 DLSw MIB using SMIv2 October 1996
is either (1) local - the resource is reachable
via an interface, or (2) remote - the resource
is reachable via a partner DLSw node (or a set
of partner DLSw nodes)."
DEFVAL { local }
::= { dlswDirMacEntry 5 }
dlswDirMacLocation OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Points to either the ifEntry, dlswTConnConfigEntry,
dlswTConnOperEntry, 0.0, or something that is implementation
specific. It identifies the location of the MAC address
(or the collection of MAC addresses.)"
DEFVAL { null }
::= { dlswDirMacEntry 6 }
dlswDirMacStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown (1),
reachable (2),
notReachable (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether DLSw currently believes
the MAC address to be accessible at the specified location.
The value `notReachable' allows a configured resource
definition to be taken out of service when a search to
that resource fails (avoiding a repeat of the search)."
DEFVAL { unknown }
::= { dlswDirMacEntry 7 }
dlswDirMacLFSize OBJECT-TYPE
SYNTAX LFSize
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The largest size of the MAC INFO field (LLC header and data)
that a circuit to the MAC address can carry through this path."
DEFVAL { lfs65535 }
::= { dlswDirMacEntry 8 }
dlswDirMacRowStatus OBJECT-TYPE
SYNTAX RowStatus
Chen, et. al. Standards Track [Page 49]
RFC 2024 DLSw MIB using SMIv2 October 1996
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used by the manager to create
or delete the row entry in the dlswDirMacTable
following the RowStatus textual convention."
::= { dlswDirMacEntry 9 }
-- ...................................................................
-- Directory for NetBIOS Names
-- All Possible combinations of values of these objects.
--
-- EntryType LocationType Location Status
-- -------------- ------------ ------------------ --------------
-- userConfigured local ifEntry or 0.0 reachable, or
-- notReachable, or
-- unknown
-- userConfigured remote TConnConfigEntry reachable, or
-- notReachable, or
-- unknown
-- partnerCapExMsg remote TConnOperEntry unknown
-- dynamic local ifEntry or 0.0 reachable
-- dynamic remote TConnOperEntry reachable
--
-- ...................................................................
dlswDirNBTable OBJECT-TYPE
SYNTAX SEQUENCE OF DlswDirNBEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains locations of NetBIOS names.
They could be either verified or not verified,
local or remote, and configured locally or learned
from either Capabilities Exchange messages or
directory searches."
::= { dlswDirCache 2 }
dlswDirNBEntry OBJECT-TYPE
SYNTAX DlswDirNBEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indexed by dlswDirNBIndex."
INDEX { dlswDirNBIndex }
::= { dlswDirNBTable 1 }
DlswDirNBEntry ::= SEQUENCE {
dlswDirNBIndex INTEGER,
Chen, et. al. Standards Track [Page 50]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswDirNBName NBName,
dlswDirNBNameType INTEGER,
dlswDirNBEntryType INTEGER,
dlswDirNBLocationType INTEGER,
dlswDirNBLocation RowPointer,
dlswDirNBStatus INTEGER,
dlswDirNBLFSize LFSize,
dlswDirNBRowStatus RowStatus
}
dlswDirNBIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies a conceptual row of this table."
::= { dlswDirNBEntry 1 }
dlswDirNBName OBJECT-TYPE
SYNTAX NBName
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NetBIOS name (including `any char' and `wildcard'
characters) specifies a set of NetBIOS names that are
defined or discovered through an interface or partner
DLSw nodes."
::= { dlswDirNBEntry 2 }
dlswDirNBNameType OBJECT-TYPE
SYNTAX INTEGER {
unknown (1),
individual (2),
group (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Whether dlswDirNBName represents an (or a set of) individual
or group NetBIOS name(s)."
DEFVAL { unknown }
::= { dlswDirNBEntry 3 }
dlswDirNBEntryType OBJECT-TYPE
SYNTAX INTEGER {
other (1),
userConfiguredPublic (2),
userConfiguredPrivate (3),
Chen, et. al. Standards Track [Page 51]
RFC 2024 DLSw MIB using SMIv2 October 1996
partnerCapExMsg (4),
dynamic (5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The cause of the creation of this conceptual row.
It could be one of the three methods: (1) user
configured, including via management protocol
set operations, configuration file, command line,
or equivalent methods; (2) learned from the
partner DLSw Capabilities Exchange messages;
and (3) dynamic, e.g., learned from ICanReach
messages, or test frames. Since only actual
NetBIOS names can be dynamically learned, dynamic
entries will not contain any char or wildcard
characters.
The public versus private distinction for user-
configured resources applies only to local resources
(UC remote resources are private), and indicates
whether that resource should be advertised in
capabilities exchange messages sent by this node."
DEFVAL { userConfiguredPublic }
::= { dlswDirNBEntry 4 }
dlswDirNBLocationType OBJECT-TYPE
SYNTAX INTEGER {
other (1),
local (2),
remote (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The location of the resource (or a collection of resources
using any char/wildcard characters) of this conceptual row
is either (1) local - the resource is reachable via an
interface, or (2) remote - the resource is reachable via a
a partner DLSw node (or a set of partner DLSw nodes)."
DEFVAL { local }
::= { dlswDirNBEntry 5 }
dlswDirNBLocation OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Chen, et. al. Standards Track [Page 52]
RFC 2024 DLSw MIB using SMIv2 October 1996
"Points to either the ifEntry, dlswTConnConfigEntry,
dlswTConnOperEntry, 0.0, or something that is implementation
specific. It identifies the location of the NetBIOS name
or the set of NetBIOS names."
DEFVAL { null }
::= { dlswDirNBEntry 6 }
dlswDirNBStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown (1),
reachable (2),
notReachable (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether DLSw currently believes
the NetBIOS name to be accessible at the specified location.
The value `notReachable' allows a configured resource
definition to be taken out of service when a search to
that resource fails (avoiding a repeat of the search)."
DEFVAL { unknown }
::= { dlswDirNBEntry 7 }
dlswDirNBLFSize OBJECT-TYPE
SYNTAX LFSize
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The largest size of the MAC INFO field (LLC header and data)
that a circuit to the NB name can carry through this path."
DEFVAL { lfs65535 }
::= { dlswDirNBEntry 8 }
dlswDirNBRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used by manager to create
or delete the row entry in the dlswDirNBTable
following the RowStatus textual convention."
::= { dlswDirNBEntry 9 }
-- -------------------------------------------------------------------
-- Resource Locations
-- -------------------------------------------------------------------
Chen, et. al. Standards Track [Page 53]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswDirLocate OBJECT IDENTIFIER ::= { dlswDirectory 3 }
-- ...................................................................
-- Locate Entries in the dlswDirMacTable for a given MAC address
-- ...................................................................
dlswDirLocateMacTable OBJECT-TYPE
SYNTAX SEQUENCE OF DlswDirLocateMacEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to retrieve all entries in the
dlswDirMacTable that match a given MAC address,
in the order of the best matched first, the
second best matched second, and so on, till
no more entries match the given MAC address."
::= { dlswDirLocate 1 }
dlswDirLocateMacEntry OBJECT-TYPE
SYNTAX DlswDirLocateMacEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indexed by dlswDirLocateMacMac and dlswDirLocateMacMatch.
The first object is the MAC address of interest, and
the second object is the order in the list of all
entries that match the MAC address."
INDEX { dlswDirLocateMacMac, dlswDirLocateMacMatch }
::= { dlswDirLocateMacTable 1 }
DlswDirLocateMacEntry ::= SEQUENCE {
dlswDirLocateMacMac MacAddressNC,
dlswDirLocateMacMatch INTEGER,
dlswDirLocateMacLocation RowPointer
}
dlswDirLocateMacMac OBJECT-TYPE
SYNTAX MacAddressNC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The MAC address to be located."
::= { dlswDirLocateMacEntry 1 }
dlswDirLocateMacMatch OBJECT-TYPE
SYNTAX INTEGER (1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Chen, et. al. Standards Track [Page 54]
RFC 2024 DLSw MIB using SMIv2 October 1996
"The order of the entries of dlswDirMacTable
that match dlswDirLocateMacMac. A value of
one represents the entry that best matches the
MAC address. A value of two represents the second
best matched entry, and so on."
::= { dlswDirLocateMacEntry 2 }
dlswDirLocateMacLocation OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Points to the dlswDirMacEntry."
::= { dlswDirLocateMacEntry 3 }
-- ...................................................................
-- Locate Entries in the dlswDirNBTable for a given NetBIOS name
-- ...................................................................
dlswDirLocateNBTable OBJECT-TYPE
SYNTAX SEQUENCE OF DlswDirLocateNBEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to retrieve all entries in the
dlswDirNBTable that match a given NetBIOS name,
in the order of the best matched first, the
second best matched second, and so on, till
no more entries match the given NetBIOS name."
::= { dlswDirLocate 2 }
dlswDirLocateNBEntry OBJECT-TYPE
SYNTAX DlswDirLocateNBEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indexed by dlswDirLocateNBName and dlswDirLocateNBMatch.
The first object is the NetBIOS name of interest, and
the second object is the order in the list of all
entries that match the NetBIOS name."
INDEX { dlswDirLocateNBName, dlswDirLocateNBMatch }
::= { dlswDirLocateNBTable 1 }
DlswDirLocateNBEntry ::= SEQUENCE {
dlswDirLocateNBName NBName,
dlswDirLocateNBMatch INTEGER,
dlswDirLocateNBLocation RowPointer
}
Chen, et. al. Standards Track [Page 55]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswDirLocateNBName OBJECT-TYPE
SYNTAX NBName
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The NetBIOS name to be located (no any char or wildcards)."
::= { dlswDirLocateNBEntry 1 }
dlswDirLocateNBMatch OBJECT-TYPE
SYNTAX INTEGER (1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The order of the entries of dlswDirNBTable
that match dlswDirLocateNBName. A value of
one represents the entry that best matches the
NetBIOS name. A value of two represents the second
best matched entry, and so on."
::= { dlswDirLocateNBEntry 2 }
dlswDirLocateNBLocation OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Points to the dlswDirNBEntry."
::= { dlswDirLocateNBEntry 3 }
-- *******************************************************************
-- CIRCUIT
-- A circuit is the end-to-end association of two DLSw entities
-- through one or two DLSw nodes. It is the concatenation of
-- two "data links", optionally with an intervening transport
-- connection. The origin of the circuit is the end station that
-- initiates the circuit. The target of the circuit is the end
-- station that receives the initiation.
-- *******************************************************************
-- -------------------------------------------------------------------
-- Statistics Related to Circuits
-- -------------------------------------------------------------------
dlswCircuitStat OBJECT IDENTIFIER ::= { dlswCircuit 1 }
dlswCircuitStatActives OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
Chen, et. al. Standards Track [Page 56]
RFC 2024 DLSw MIB using SMIv2 October 1996
DESCRIPTION
"The current number of circuits in dlswCircuitTable that are
not in the disconnected state."
::= { dlswCircuitStat 1 }
dlswCircuitStatCreates OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of entries ever added to dlswCircuitTable,
or reactivated upon exiting `disconnected' state."
::= { dlswCircuitStat 2 }
-- -------------------------------------------------------------------
-- Circuit Table
--
-- This table is the DLSw entity's view of circuits. There will be
-- a conceptual row in the table associated with each data link.
--
-- The chart below lists the various possible combinations of
-- origin and target MAC locations and the number of entries in
-- this Circuit Table:
--
-- number of | Origin End Station Location
-- entries in the |--------------------------------------
-- Circuit Table | internal local remote
-- -----------------------|--------------------------------------
-- Target | internal | NA 2 1
-- End | local | 2 2 1
-- Station | remote | 1 1 NA
-- Location | |
--
-- NA: Not applicable
--
-- Note:
-- (a) IfIndex and RouteInfo are applied only if location is local.
-- (b) TDomain and TAddr are applied only if location is remote.
--
-- Most of statistics related to circuits can be collected
-- from LLC-2 Link Station Table.
-- -------------------------------------------------------------------
dlswCircuitTable OBJECT-TYPE
SYNTAX SEQUENCE OF DlswCircuitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Chen, et. al. Standards Track [Page 57]
RFC 2024 DLSw MIB using SMIv2 October 1996
"This table is the circuit representation in the DLSw
entity. Virtual data links are used to represent any internal
end stations. There is a conceptual row associated with
each data link. Thus, for circuits without an intervening
transport connection, there are two conceptual rows
for each circuit.
The table consists of the circuits being established,
established, and as an implementation option, circuits that
have been disconnected. For circuits carried over
transport connections, an entry is created after
the CUR_cs was sent or received. For circuits between
two locally attached devices, or internal virtual MAC
addresses, an entry is created when the equivalent of
CUR_cs sent/received status is reached.
End station 1 (S1) and End station 2 (S2) are used to
represent the two end stations of the circuit.
S1 is always an end station which is locally attached.
S2 may be locally attached or remote. If it is locally
attached, the circuit will be represented by two rows indexed
by (A, B) and (B, A) where A & B are the relevant MACs/SAPs.
The table may be used to store the causes of disconnection of
circuits. It is recommended that the oldest disconnected
circuit entry be removed from this table when the memory
space of disconnected circuits is needed."
::= { dlswCircuit 2 }
dlswCircuitEntry OBJECT-TYPE
SYNTAX DlswCircuitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
""
INDEX { dlswCircuitS1Mac,
dlswCircuitS1Sap,
dlswCircuitS2Mac,
dlswCircuitS2Sap }
::= { dlswCircuitTable 1 }
DlswCircuitEntry ::= SEQUENCE {
dlswCircuitS1Mac MacAddressNC,
dlswCircuitS1Sap OCTET STRING,
dlswCircuitS1IfIndex INTEGER,
dlswCircuitS1DlcType DlcType,
dlswCircuitS1RouteInfo OCTET STRING,
dlswCircuitS1CircuitId OCTET STRING,
Chen, et. al. Standards Track [Page 58]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswCircuitS1Dlc RowPointer,
dlswCircuitS2Mac MacAddressNC,
dlswCircuitS2Sap OCTET STRING,
dlswCircuitS2Location EndStationLocation,
dlswCircuitS2TDomain OBJECT IDENTIFIER,
dlswCircuitS2TAddress TAddress,
dlswCircuitS2CircuitId OCTET STRING,
dlswCircuitOrigin INTEGER,
dlswCircuitEntryTime TimeTicks,
dlswCircuitStateTime TimeTicks,
dlswCircuitState INTEGER,
dlswCircuitPriority INTEGER,
dlswCircuitFCSendGrantedUnits INTEGER,
dlswCircuitFCSendCurrentWndw INTEGER,
dlswCircuitFCRecvGrantedUnits INTEGER,
dlswCircuitFCRecvCurrentWndw INTEGER,
dlswCircuitFCLargestRecvGranted Gauge32,
dlswCircuitFCLargestSendGranted Gauge32,
dlswCircuitFCHalveWndwSents Counter32,
dlswCircuitFCResetOpSents Counter32,
dlswCircuitFCHalveWndwRcvds Counter32,
dlswCircuitFCResetOpRcvds Counter32,
dlswCircuitDiscReasonLocal INTEGER,
dlswCircuitDiscReasonRemote INTEGER,
dlswCircuitDiscReasonRemoteData OCTET STRING
}
-- ...................................................................
-- Information related to the End Station 1 (S1).
-- ...................................................................
dlswCircuitS1Mac OBJECT-TYPE
SYNTAX MacAddressNC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The MAC Address of End Station 1 (S1) used for this circuit."
::= { dlswCircuitEntry 1 }
dlswCircuitS1Sap OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Chen, et. al. Standards Track [Page 59]
RFC 2024 DLSw MIB using SMIv2 October 1996
"The SAP at End Station 1 (S1) used for this circuit."
::= { dlswCircuitEntry 2 }
dlswCircuitS1IfIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifEntry index of the local interface through which S1
can be reached."
::= { dlswCircuitEntry 3 }
dlswCircuitS1DlcType OBJECT-TYPE
SYNTAX DlcType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The DLC protocol in use between the DLSw node and S1."
::= { dlswCircuitEntry 4 }
dlswCircuitS1RouteInfo OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..30))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If source-route bridging is in use between the DLSw
node and S1, this is the routing information field
describing the path between the two devices.
Otherwise the value will be an OCTET STRING of
zero length."
::= { dlswCircuitEntry 5 }
dlswCircuitS1CircuitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0 | 8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Circuit ID assigned by this DLSw node to this circuit.
The first four octets are the DLC port Id, and
the second four octets are the Data Link Correlator.
If the DLSw SSP was not used to establish this circuit,
the value will be a string of zero length."
::= { dlswCircuitEntry 6 }
dlswCircuitS1Dlc OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
Chen, et. al. Standards Track [Page 60]
RFC 2024 DLSw MIB using SMIv2 October 1996
DESCRIPTION
"Points to a conceptual row of the underlying DLC MIB,
which could either be the standard MIBs (e.g., the SDLC),
or an enterprise-specific DLC MIB."
::= { dlswCircuitEntry 7 }
-- ...................................................................
-- Information related to the End Station 2 (S2).
-- ...................................................................
dlswCircuitS2Mac OBJECT-TYPE
SYNTAX MacAddressNC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The MAC Address of End Station 2 (S2) used for this circuit."
::= { dlswCircuitEntry 8 }
dlswCircuitS2Sap OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SAP at End Station 2 (S2) used for this circuit."
::= { dlswCircuitEntry 9 }
dlswCircuitS2Location OBJECT-TYPE
SYNTAX EndStationLocation
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The location of End Station 2 (S2).
If the location of End Station 2 is local, the
interface information will be available in the
conceptual row whose S1 and S2 are the S2 and
the S1 of this conceptual row, respectively."
::= { dlswCircuitEntry 10 }
dlswCircuitS2TDomain OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the location of End Station 2 is remote,
this value is the transport domain of the
transport protocol the circuit is running
over. Otherwise, the value is 0.0."
::= { dlswCircuitEntry 11 }
Chen, et. al. Standards Track [Page 61]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswCircuitS2TAddress OBJECT-TYPE
SYNTAX TAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the location of End Station 2 is remote,
this object contains the address of the partner
DLSw, else it will be an OCTET STRING of zero length."
::= { dlswCircuitEntry 12 }
dlswCircuitS2CircuitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0 | 8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Circuit ID assigned to this circuit by the partner
DLSw node. The first four octets are the DLC port Id, and
the second four octets are the Data Link Correlator.
If the DLSw SSP was not used to establish this circuit,
the value will be a string of zero length."
::= { dlswCircuitEntry 13 }
-- ...................................................................
dlswCircuitOrigin OBJECT-TYPE
SYNTAX INTEGER {
s1 (1),
s2 (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies which of the two end stations
initiated the establishment of this circuit."
::= { dlswCircuitEntry 14 }
-- ...................................................................
-- Operational information related to this circuit.
-- ...................................................................
dlswCircuitEntryTime OBJECT-TYPE
SYNTAX TimeTicks
UNITS "hundredths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time (in hundredths of a second) since this
circuit table conceptual row was created."
::= { dlswCircuitEntry 15 }
Chen, et. al. Standards Track [Page 62]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswCircuitStateTime OBJECT-TYPE
SYNTAX TimeTicks
UNITS "hundredths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time (in hundredths of a second) since this
circuit entered the current state."
::= { dlswCircuitEntry 16 }
dlswCircuitState OBJECT-TYPE
SYNTAX INTEGER {
disconnected (1),
circuitStart (2),
resolvePending (3),
circuitPending (4),
circuitEstablished (5),
connectPending (6),
contactPending (7),
connected (8),
disconnectPending (9),
haltPending (10),
haltPendingNoack (11),
circuitRestart (12),
restartPending (13)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The current state of this circuit. The agent, implementation
specific, may choose to keep entries for some period of time
after circuit disconnect, so the manager can gather the time
and cause of disconnection.
While all of the specified values may be returned from a GET
operation, the only SETable value is `disconnectPending'.
When this value is set, DLSw should perform the appropriate
action given its previous state (e.g., send HALT_DL if the
state was `connected') to bring the circuit down to the
`disconnected' state. Both the partner DLSw and local end
station(s) should be notified as appropriate.
This MIB provides no facility to re-establish a disconnected
circuit, because in DLSw this should be an end station-driven
function."
::= { dlswCircuitEntry 17 }
dlswCircuitPriority OBJECT-TYPE
Chen, et. al. Standards Track [Page 63]
RFC 2024 DLSw MIB using SMIv2 October 1996
SYNTAX INTEGER {
unsupported (1),
low (2),
medium (3),
high (4),
highest (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transmission priority of this circuit as understood by
this DLSw node. This value is determined by the two DLSw
nodes at circuit startup time. If this DLSw node does not
support DLSw circuit priority, the value `unsupported' should
be returned."
::= { dlswCircuitEntry 18 }
-- ...................................................................
-- Pacing Objects:
-- These objects are applicable if DLSw is using the SSP circuit
-- pacing protocol to control the flow between the two data links
-- in this circuit.
-- ...................................................................
dlswCircuitFCSendGrantedUnits OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of paced SSP messages that this DLSw is currently
authorized to send on this circuit before it must stop and
wait for an additional flow control indication from the
partner DLSw.
The value zero should be returned if this circuit is not
running the DLSw pacing protocol."
::= { dlswCircuitEntry 19 }
dlswCircuitFCSendCurrentWndw OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current window size that this DLSw is using in its role
as a data sender. This is the value by which this DLSw would
increase the number of messages it is authorized to send, if
it were to receive a flow control indication with the bits
specifying `repeat window'.
Chen, et. al. Standards Track [Page 64]
RFC 2024 DLSw MIB using SMIv2 October 1996
The value zero should be returned if this circuit is not
running the DLSw pacing protocol."
::= { dlswCircuitEntry 20 }
dlswCircuitFCRecvGrantedUnits OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current number of paced SSP messages that this DLSw has
authorized the partner DLSw to send on this circuit before
the partner DLSw must stop and wait for an additional flow
control indication from this DLSw.
The value zero should be returned if this circuit is not
running the DLSw pacing protocol."
::= { dlswCircuitEntry 21 }
dlswCircuitFCRecvCurrentWndw OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current window size that this DLSw is using in its role
as a data receiver. This is the number of additional paced
SSP messages that this DLSw would be authorizing its DLSw
partner to send, if this DLSw were to send a flow control
indication with the bits specifying `repeat window'.
The value zero should be returned if this circuit is not
running the DLSw pacing protocol."
::= { dlswCircuitEntry 22 }
dlswCircuitFCLargestRecvGranted OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The largest receive window size granted by this DLSw during
the current activation of this circuit. This is not the
largest number of messages granted at any time, but the
largest window size as represented by FCIND operator bits.
The value zero should be returned if this circuit is not
running the DLSw pacing protocol."
::= { dlswCircuitEntry 23 }
dlswCircuitFCLargestSendGranted OBJECT-TYPE
Chen, et. al. Standards Track [Page 65]
RFC 2024 DLSw MIB using SMIv2 October 1996
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The largest send (with respect to this DLSw) window size
granted by the partner DLSw during the current activation of
this circuit.
The value zero should be returned if this circuit is not
running the DLSw pacing protocol."
::= { dlswCircuitEntry 24 }
dlswCircuitFCHalveWndwSents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Halve Window operations this DLSw has sent on
this circuit, in its role as a data receiver.
The value zero should be returned if this circuit is not
running the DLSw pacing protocol."
::= { dlswCircuitEntry 25 }
dlswCircuitFCResetOpSents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Reset Window operations this DLSw has sent on
this circuit, in its role as a data receiver.
The value zero should be returned if this circuit is not
running the DLSw pacing protocol."
::= { dlswCircuitEntry 26 }
dlswCircuitFCHalveWndwRcvds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Halve Window operations this DLSw has received on
this circuit, in its role as a data sender.
The value zero should be returned if this circuit is not
running the DLSw pacing protocol."
::= { dlswCircuitEntry 27 }
Chen, et. al. Standards Track [Page 66]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswCircuitFCResetOpRcvds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Reset Window operations this DLSw has received on
this circuit, in its role as a data sender.
The value zero should be returned if this circuit is not
running the DLSw pacing protocol."
::= { dlswCircuitEntry 28 }
-- ...................................................................
-- Information about the circuit disconnection
-- ...................................................................
dlswCircuitDiscReasonLocal OBJECT-TYPE
SYNTAX INTEGER {
endStationDiscRcvd (1),
endStationDlcError (2),
protocolError (3),
operatorCommand (4),
haltDlRcvd (5),
haltDlNoAckRcvd (6),
transportConnClosed (7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The reason why this circuit was last disconnected, as seen
by this DLSw node.
This object is present only if the agent keeps circuit
table entries around for some period after circuit disconnect."
::= { dlswCircuitEntry 29 }
dlswCircuitDiscReasonRemote OBJECT-TYPE
SYNTAX INTEGER {
unknown (1),
endStationDiscRcvd (2),
endStationDlcError (3),
protocolError (4),
operatorCommand (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The generic reason code why this circuit was last
disconnected, as reported by the DLSw partner in a HALT_DL
Chen, et. al. Standards Track [Page 67]
RFC 2024 DLSw MIB using SMIv2 October 1996
or HALT_DL_NOACK. If the partner does not send a reason
code in these messages, or the DLSw implementation does
not report receiving one, the value `unknown' is returned.
This object is present only if the agent keeps circuit table
entries around for some period after circuit disconnect."
::= { dlswCircuitEntry 30 }
dlswCircuitDiscReasonRemoteData OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0 | 4))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Implementation-specific data reported by the DLSw partner in
a HALT_DL or HALT_DL_NOACK, to help specify how and why this
circuit was last disconnected. If the partner does not send
this data in these messages, or the DLSw implementation does
not report receiving it, a string of zero length is returned.
This object is present only if the agent keeps circuit table
entries around for some period after circuit disconnect."
::= { dlswCircuitEntry 31 }
-- ...................................................................
-- Statistics related to this circuit.
-- All statistics are in LLC-2 Link Station Statistical Table.
-- All SDLC statistics are in SDLC MIB
-- ...................................................................
-- *******************************************************************
-- DLSW SDLC EXTENSION
-- *******************************************************************
dlswSdlcLsEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of entries in dlswSdlcLsTable."
::= { dlswSdlc 1 }
-- ...................................................................
dlswSdlcLsTable OBJECT-TYPE
SYNTAX SEQUENCE OF DlswSdlcLsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Chen, et. al. Standards Track [Page 68]
RFC 2024 DLSw MIB using SMIv2 October 1996
"The table defines the virtual MAC addresses for those
SDLC link stations that participate in data link switching."
::= { dlswSdlc 2 }
dlswSdlcLsEntry OBJECT-TYPE
SYNTAX DlswSdlcLsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this table is the ifIndex value for the
SDLC port which owns this link station and the poll
address of the particular SDLC link station."
INDEX { ifIndex, sdlcLSAddress }
::= { dlswSdlcLsTable 1 }
DlswSdlcLsEntry ::= SEQUENCE {
dlswSdlcLsLocalMac MacAddressNC,
dlswSdlcLsLocalSap OCTET STRING,
dlswSdlcLsLocalIdBlock DisplayString,
dlswSdlcLsLocalIdNum DisplayString,
dlswSdlcLsRemoteMac MacAddressNC,
dlswSdlcLsRemoteSap OCTET STRING,
dlswSdlcLsRowStatus RowStatus
}
dlswSdlcLsLocalMac OBJECT-TYPE
SYNTAX MacAddressNC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The virtual MAC address used to represent the SDLC-attached
link station to the rest of the DLSw network."
::= { dlswSdlcLsEntry 1 }
dlswSdlcLsLocalSap OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SAP used to represent this link station."
::= { dlswSdlcLsEntry 2 }
dlswSdlcLsLocalIdBlock OBJECT-TYPE
SYNTAX DisplayString (SIZE (0 | 3))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The block number is the first three digits of the node_id,
Chen, et. al. Standards Track [Page 69]
RFC 2024 DLSw MIB using SMIv2 October 1996
if available. These 3 hexadecimal digits identify the
product."
DEFVAL { ''H }
::= { dlswSdlcLsEntry 3 }
dlswSdlcLsLocalIdNum OBJECT-TYPE
SYNTAX DisplayString (SIZE (0 | 5))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The ID number is the last 5 digits of the node_id, if
available. These 5 hexadecimal digits are
administratively defined and combined with the 3 digit
block number form the node_id. This node_id is used to
identify the local node and is included in SNA XIDs."
DEFVAL { ''H }
::= { dlswSdlcLsEntry 4 }
dlswSdlcLsRemoteMac OBJECT-TYPE
SYNTAX MacAddressNC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The MAC address to which DLSw should attempt to connect
this link station. If this information is not available,
a length of zero for this object should be returned."
DEFVAL { ''H }
::= { dlswSdlcLsEntry 5 }
dlswSdlcLsRemoteSap OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0 | 1))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SAP of the remote station to which this link
station should be connected. If this information
is not available, a length of zero for this object
should be returned."
DEFVAL { ''H }
::= { dlswSdlcLsEntry 6 }
dlswSdlcLsRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used by the manager to create
or delete the row entry in the dlswSdlcLsTable
Chen, et. al. Standards Track [Page 70]
RFC 2024 DLSw MIB using SMIv2 October 1996
following the RowStatus textual convention."
::= { dlswSdlcLsEntry 7 }
-- *******************************************************************
-- TRAP GENERATION CONTROL
-- *******************************************************************
dlswTrapControl OBJECT IDENTIFIER ::= { dlswNode 10}
dlswTrapCntlTConnPartnerReject OBJECT-TYPE
SYNTAX INTEGER {
enabled (1),
disabled (2),
partial (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the DLSw is permitted to emit partner
reject related traps. With the value of `enabled'
the DLSw will emit all partner reject related traps.
With the value of `disabled' the DLSw will not emit
any partner reject related traps. With the value
of `partial' the DLSw will only emits partner reject
traps for CapEx reject. The changes take effect
immediately."
::= { dlswTrapControl 1 }
dlswTrapCntlTConnProtViolation OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the DLSw is permitted to generate
protocol-violation traps on the events such as
window size violation. The changes take effect
immediately."
::= { dlswTrapControl 2 }
dlswTrapCntlTConn OBJECT-TYPE
SYNTAX INTEGER {
enabled (1),
disabled (2),
partial (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
Chen, et. al. Standards Track [Page 71]
RFC 2024 DLSw MIB using SMIv2 October 1996
"Indicates whether the DLSw is permitted to emit transport
connection up and down traps. With the value of `enabled'
the DLSw will emit traps when connections enter `connected'
and `disconnected' states. With the value of `disabled'
the DLSw will not emit traps when connections enter of
`connected' and `disconnected' states. With the value
of `partial' the DLSw will only emits transport connection
down traps when the connection is closed with busy.
The changes take effect immediately."
::= { dlswTrapControl 3 }
dlswTrapCntlCircuit OBJECT-TYPE
SYNTAX INTEGER {
enabled (1),
disabled (2),
partial (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the DLSw is permitted to generate
circuit up and down traps. With the value of `enabled'
the DLSw will emit traps when circuits enter `connected'
and `disconnected' states. With the value of `disabled'
the DLSw will not emit traps when circuits enter of
`connected' and `disconnected' states. With the value
of `partial' the DLSw will emit traps only for those
circuits that are initiated by this DLSw, e.g.,
originating the CUR_CS message. The changes take effect
immediately."
::= { dlswTrapControl 4 }
-- *******************************************************************
-- NOTIFICATIONS, i.e., TRAP DEFINITIONS
-- *******************************************************************
dlswTraps OBJECT IDENTIFIER ::= { dlswMIB 0 }
-- -------------------------------------------------------------------
-- This section defines the well-known notifications sent by
-- DLSW agents.
-- Care must be taken to insure that no particular notification
-- is sent to a single receiving entity more often than once
-- every five seconds.
--
-- Traps includes:
-- (1) Partner rejected (capEx rejection, not in partner list, etc.)
-- (2) DLSw protocol violation (e.g., window size violation, etc.)
-- (3) Transport connection up/down
Chen, et. al. Standards Track [Page 72]
RFC 2024 DLSw MIB using SMIv2 October 1996
-- (4) Circuit up/down
-- -------------------------------------------------------------------
--
dlswTrapTConnPartnerReject NOTIFICATION-TYPE
OBJECTS { dlswTConnOperTDomain, dlswTConnOperRemoteTAddr
}
STATUS current
DESCRIPTION
"This trap is sent each time a transport connection
is rejected by a partner DLSw during Capabilities
Exchanges. The emission of this trap is controlled
by dlswTrapCntlTConnPartnerReject."
::= { dlswTraps 1 }
dlswTrapTConnProtViolation NOTIFICATION-TYPE
OBJECTS { dlswTConnOperTDomain, dlswTConnOperRemoteTAddr
}
STATUS current
DESCRIPTION
"This trap is sent each time a protocol violation is
detected for a transport connection. The emission of this
trap is controlled by dlswTrapCntlTConnProtViolation."
::= { dlswTraps 2 }
dlswTrapTConnUp NOTIFICATION-TYPE
OBJECTS { dlswTConnOperTDomain, dlswTConnOperRemoteTAddr
}
STATUS current
DESCRIPTION
"This trap is sent each time a transport connection
enters `connected' state. The emission of this trap
is controlled by dlswTrapCntlTConn."
::= { dlswTraps 3 }
dlswTrapTConnDown NOTIFICATION-TYPE
OBJECTS { dlswTConnOperTDomain, dlswTConnOperRemoteTAddr
}
STATUS current
DESCRIPTION
"This trap is sent each time a transport connection
enters `disconnected' state. The emission of this trap
is controlled by dlswTrapCntlTConn."
::= { dlswTraps 4 }
dlswTrapCircuitUp NOTIFICATION-TYPE
OBJECTS { dlswCircuitS1Mac, dlswCircuitS1Sap,
dlswCircuitS2Mac, dlswCircuitS2Sap
Chen, et. al. Standards Track [Page 73]
RFC 2024 DLSw MIB using SMIv2 October 1996
}
STATUS current
DESCRIPTION
"This trap is sent each time a circuit enters `connected'
state. The emission of this trap is controlled by
dlswTrapCntlCircuit."
::= { dlswTraps 5 }
dlswTrapCircuitDown NOTIFICATION-TYPE
OBJECTS { dlswCircuitS1Mac, dlswCircuitS1Sap,
dlswCircuitS2Mac, dlswCircuitS2Sap
}
STATUS current
DESCRIPTION
"This trap is sent each time a circuit enters `disconnected'
state. The emission of this trap is controlled by
dlswTrapCntlCircuit."
::= { dlswTraps 6 }
-- *******************************************************************
-- CONFORMANCE INFORMATION
-- *******************************************************************
dlswConformance OBJECT IDENTIFIER ::= { dlsw 3 }
dlswCompliances OBJECT IDENTIFIER ::= { dlswConformance 1 }
dlswGroups OBJECT IDENTIFIER ::= { dlswConformance 2 }
-- -------------------------------------------------------------------
-- COMPLIANCE STATEMENTS
-- -------------------------------------------------------------------
-- ...................................................................
-- Core compliance for all DLSw entities
-- ...................................................................
dlswCoreCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The core compliance statement for all DLSw nodes."
MODULE
MANDATORY-GROUPS {
dlswNodeGroup,
dlswTConnStatGroup,
dlswTConnConfigGroup,
dlswTConnOperGroup,
dlswInterfaceGroup,
dlswCircuitGroup,
dlswCircuitStatGroup,
Chen, et. al. Standards Track [Page 74]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswNotificationGroup }
GROUP dlswNodeNBGroup
DESCRIPTION
"The DLSw NetBIOS Node group is mandatory only for
those DLSw entities that implement NetBIOS."
GROUP dlswTConnNBGroup
DESCRIPTION
"The DLSw NetBIOS Transport Connection group is
mandatory only for those DLSw entities that
implement NetBIOS."
OBJECT dlswNodeStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswNodeVirtualSegmentLFSize
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswNodeResourceNBExclusivity
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswNodeResourceMacExclusivity
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTrapCntlTConnPartnerReject
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTrapCntlTConnProtViolation
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTrapCntlTConn
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Chen, et. al. Standards Track [Page 75]
RFC 2024 DLSw MIB using SMIv2 October 1996
OBJECT dlswTrapCntlCircuit
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnConfigTDomain
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnConfigLocalTAddr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnConfigRemoteTAddr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnConfigEntryType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnConfigGroupDefinition
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnConfigSetupType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnConfigSapList
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnConfigAdvertiseMacNB
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnConfigInitCirRecvWndw
MIN-ACCESS read-only
DESCRIPTION
Chen, et. al. Standards Track [Page 76]
RFC 2024 DLSw MIB using SMIv2 October 1996
"Write access is not required."
OBJECT dlswTConnConfigRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnOperState
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswIfRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswIfVirtualSegment
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswIfSapList
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswCircuitState
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { dlswCompliances 1 }
-- ...................................................................
-- Compliance for all DLSw entities that provide TCP transport.
-- ...................................................................
dlswTConnTcpCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance for DLSw nodes that use TCP as a
transport connection protocol."
MODULE
MANDATORY-GROUPS {
dlswTConnTcpConfigGroup,
dlswTConnTcpOperGroup }
OBJECT dlswTConnTcpConfigKeepAliveInt
Chen, et. al. Standards Track [Page 77]
RFC 2024 DLSw MIB using SMIv2 October 1996
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnTcpConfigTcpConnections
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswTConnTcpConfigMaxSegmentSize
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { dlswCompliances 2 }
-- ...................................................................
-- Compliance for all DLSw Entities that implement a directory
-- ...................................................................
dlswDirCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance for DLSw nodes that provide a directory
function."
MODULE
MANDATORY-GROUPS {
dlswDirGroup }
GROUP dlswDirNBGroup
DESCRIPTION
"The DLSw NetBIOS group is mandatory only for
those DLSw entities that implement NetBIOS."
OBJECT dlswDirMacMac
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirMacMask
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirMacEntryType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Chen, et. al. Standards Track [Page 78]
RFC 2024 DLSw MIB using SMIv2 October 1996
OBJECT dlswDirMacLocationType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirMacLocation
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirMacStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirMacLFSize
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirMacRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirNBName
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirNBNameType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirNBEntryType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirNBLocationType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirNBLocation
MIN-ACCESS read-only
DESCRIPTION
Chen, et. al. Standards Track [Page 79]
RFC 2024 DLSw MIB using SMIv2 October 1996
"Write access is not required."
OBJECT dlswDirNBStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirNBLFSize
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswDirNBRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { dlswCompliances 3 }
-- ...................................................................
-- Compliance for all DLSw entities that provide an ordered
-- list of directory entries that match a resource
-- ...................................................................
dlswDirLocateCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance for DLSw nodes that provide an ordered
list of directory entries for a given resource."
MODULE
MANDATORY-GROUPS {
dlswDirLocateGroup }
GROUP dlswDirLocateNBGroup
DESCRIPTION
"The DLSw NetBIOS group is mandatory only for
those DLSw entities that implement NetBIOS."
::= { dlswCompliances 4 }
-- ...................................................................
-- Compliance for all DLSw entities that support SDLC end stations
-- ...................................................................
dlswSdlcCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance for DLSw nodes that support SDLC."
MODULE
MANDATORY-GROUPS {
Chen, et. al. Standards Track [Page 80]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswSdlcGroup }
OBJECT dlswSdlcLsLocalMac
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswSdlcLsLocalSap
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswSdlcLsLocalIdBlock
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswSdlcLsLocalIdNum
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswSdlcLsRemoteMac
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswSdlcLsRemoteSap
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT dlswSdlcLsRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { dlswCompliances 5 }
-- -------------------------------------------------------------------
-- CONFORMANCE GROUPS
-- -------------------------------------------------------------------
-- ...................................................................
-- Node Conformance Group
-- ...................................................................
dlswNodeGroup OBJECT-GROUP
OBJECTS {
Chen, et. al. Standards Track [Page 81]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswNodeVersion,
dlswNodeVendorID,
dlswNodeVersionString,
dlswNodeStdPacingSupport,
dlswNodeStatus,
dlswNodeUpTime,
dlswNodeVirtualSegmentLFSize,
dlswNodeResourceMacExclusivity,
dlswTrapCntlTConnPartnerReject,
dlswTrapCntlTConnProtViolation,
dlswTrapCntlTConn,
dlswTrapCntlCircuit
}
STATUS current
DESCRIPTION
"Conformance group for DLSw node general information."
::= { dlswGroups 1 }
-- ...................................................................
dlswNodeNBGroup OBJECT-GROUP
OBJECTS {
dlswNodeResourceNBExclusivity
}
STATUS current
DESCRIPTION
"Conformance group for DLSw node general information
specifically for nodes that support NetBIOS."
::= { dlswGroups 2 }
-- ...................................................................
dlswTConnStatGroup OBJECT-GROUP
OBJECTS {
dlswTConnStatActiveConnections,
dlswTConnStatCloseIdles,
dlswTConnStatCloseBusys
}
STATUS current
DESCRIPTION
"Conformance group for statistics for transport
connections."
::= { dlswGroups 3 }
-- ...................................................................
dlswTConnConfigGroup OBJECT-GROUP
OBJECTS {
dlswTConnConfigTDomain,
dlswTConnConfigLocalTAddr,
dlswTConnConfigRemoteTAddr,
Chen, et. al. Standards Track [Page 82]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswTConnConfigLastModifyTime,
dlswTConnConfigEntryType,
dlswTConnConfigGroupDefinition,
dlswTConnConfigSetupType,
dlswTConnConfigSapList,
dlswTConnConfigAdvertiseMacNB,
dlswTConnConfigInitCirRecvWndw,
dlswTConnConfigOpens,
dlswTConnConfigRowStatus
}
STATUS current
DESCRIPTION
"Conformance group for the configuration of
transport connections."
::= { dlswGroups 4 }
-- ...................................................................
dlswTConnOperGroup OBJECT-GROUP
OBJECTS {
dlswTConnOperLocalTAddr,
dlswTConnOperEntryTime,
dlswTConnOperConnectTime,
dlswTConnOperState,
dlswTConnOperConfigIndex,
dlswTConnOperFlowCntlMode,
dlswTConnOperPartnerVersion,
dlswTConnOperPartnerVendorID,
dlswTConnOperPartnerVersionStr,
dlswTConnOperPartnerInitPacingWndw,
dlswTConnOperPartnerSapList,
dlswTConnOperPartnerMacExcl,
dlswTConnOperPartnerMacInfo,
dlswTConnOperDiscTime,
dlswTConnOperDiscReason,
dlswTConnOperDiscActiveCir,
dlswTConnOperInDataPkts,
dlswTConnOperOutDataPkts,
dlswTConnOperInDataOctets,
dlswTConnOperOutDataOctets,
dlswTConnOperInCntlPkts,
dlswTConnOperOutCntlPkts,
dlswTConnOperCURexSents,
dlswTConnOperICRexRcvds,
dlswTConnOperCURexRcvds,
dlswTConnOperICRexSents,
dlswTConnOperCirCreates,
dlswTConnOperCircuits
}
Chen, et. al. Standards Track [Page 83]
RFC 2024 DLSw MIB using SMIv2 October 1996
STATUS current
DESCRIPTION
"Conformance group for operation information for
transport connections."
::= { dlswGroups 5 }
-- ...................................................................
dlswTConnNBGroup OBJECT-GROUP
OBJECTS {
dlswTConnOperPartnerNBExcl,
dlswTConnOperPartnerNBInfo,
dlswTConnOperNQexSents,
dlswTConnOperNRexRcvds,
dlswTConnOperNQexRcvds,
dlswTConnOperNRexSents
}
STATUS current
DESCRIPTION
"Conformance group for operation information for
transport connections, specifically for nodes
that support NetBIOS."
::= { dlswGroups 6 }
-- ...................................................................
dlswTConnTcpConfigGroup OBJECT-GROUP
OBJECTS {
dlswTConnTcpConfigKeepAliveInt,
dlswTConnTcpConfigTcpConnections,
dlswTConnTcpConfigMaxSegmentSize
}
STATUS current
DESCRIPTION
"Conformance group for configuration information for
transport connections using TCP."
::= { dlswGroups 7 }
-- ...................................................................
dlswTConnTcpOperGroup OBJECT-GROUP
OBJECTS {
dlswTConnTcpOperKeepAliveInt,
dlswTConnTcpOperPrefTcpConnections,
dlswTConnTcpOperTcpConnections
}
STATUS current
DESCRIPTION
"Conformance group for operation information for
transport connections using TCP."
::= { dlswGroups 8 }
Chen, et. al. Standards Track [Page 84]
RFC 2024 DLSw MIB using SMIv2 October 1996
-- ...................................................................
dlswInterfaceGroup OBJECT-GROUP
OBJECTS {
dlswIfRowStatus,
dlswIfVirtualSegment,
dlswIfSapList
}
STATUS current
DESCRIPTION
"Conformance group for DLSw interfaces."
::= { dlswGroups 9 }
-- ...................................................................
dlswDirGroup OBJECT-GROUP
OBJECTS {
dlswDirMacEntries,
dlswDirMacCacheHits,
dlswDirMacCacheMisses,
dlswDirMacCacheNextIndex,
dlswDirMacMac,
dlswDirMacMask,
dlswDirMacEntryType,
dlswDirMacLocationType,
dlswDirMacLocation,
dlswDirMacStatus,
dlswDirMacLFSize,
dlswDirMacRowStatus
}
STATUS current
DESCRIPTION
"Conformance group for DLSw directory using MAC
addresses."
::= { dlswGroups 10 }
-- ...................................................................
dlswDirNBGroup OBJECT-GROUP
OBJECTS {
dlswDirNBEntries,
dlswDirNBCacheHits,
dlswDirNBCacheMisses,
dlswDirNBCacheNextIndex,
dlswDirNBName,
dlswDirNBNameType,
dlswDirNBEntryType,
dlswDirNBLocationType,
dlswDirNBLocation,
dlswDirNBStatus,
dlswDirNBLFSize,
Chen, et. al. Standards Track [Page 85]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswDirNBRowStatus
}
STATUS current
DESCRIPTION
"Conformance group for DLSw directory using NetBIOS
names."
::= { dlswGroups 11 }
-- ...................................................................
dlswDirLocateGroup OBJECT-GROUP
OBJECTS {
dlswDirLocateMacLocation
}
STATUS current
DESCRIPTION
"Conformance group for a node that can return directory
entry order for a given MAC address."
::= { dlswGroups 12 }
-- ...................................................................
dlswDirLocateNBGroup OBJECT-GROUP
OBJECTS {
dlswDirLocateNBLocation
}
STATUS current
DESCRIPTION
"Conformance group for a node that can return directory
entry order for a given NetBIOS name."
::= { dlswGroups 13 }
-- ...................................................................
dlswCircuitStatGroup OBJECT-GROUP
OBJECTS {
dlswCircuitStatActives,
dlswCircuitStatCreates
}
STATUS current
DESCRIPTION
"Conformance group for statistics about circuits."
::= { dlswGroups 14 }
-- ...................................................................
dlswCircuitGroup OBJECT-GROUP
OBJECTS {
dlswCircuitS1IfIndex,
dlswCircuitS1DlcType,
dlswCircuitS1RouteInfo,
dlswCircuitS1CircuitId,
Chen, et. al. Standards Track [Page 86]
RFC 2024 DLSw MIB using SMIv2 October 1996
dlswCircuitS1Dlc,
dlswCircuitS2Location,
dlswCircuitS2TDomain,
dlswCircuitS2TAddress,
dlswCircuitS2CircuitId,
dlswCircuitOrigin,
dlswCircuitEntryTime,
dlswCircuitStateTime,
dlswCircuitState,
dlswCircuitPriority,
dlswCircuitFCSendGrantedUnits,
dlswCircuitFCSendCurrentWndw,
dlswCircuitFCRecvGrantedUnits,
dlswCircuitFCRecvCurrentWndw,
dlswCircuitFCLargestRecvGranted,
dlswCircuitFCLargestSendGranted,
dlswCircuitFCHalveWndwSents,
dlswCircuitFCResetOpSents,
dlswCircuitFCHalveWndwRcvds,
dlswCircuitFCResetOpRcvds,
dlswCircuitDiscReasonLocal,
dlswCircuitDiscReasonRemote,
dlswCircuitDiscReasonRemoteData
}
STATUS current
DESCRIPTION
"Conformance group for DLSw circuits."
::= { dlswGroups 15 }
-- ...................................................................
dlswSdlcGroup OBJECT-GROUP
OBJECTS {
dlswSdlcLsEntries,
dlswSdlcLsLocalMac,
dlswSdlcLsLocalSap,
dlswSdlcLsLocalIdBlock,
dlswSdlcLsLocalIdNum,
dlswSdlcLsRemoteMac,
dlswSdlcLsRemoteSap,
dlswSdlcLsRowStatus
}
STATUS current
DESCRIPTION
"Conformance group for DLSw SDLC support."
::= { dlswGroups 16 }
-- ...................................................................
dlswNotificationGroup NOTIFICATION-GROUP
Chen, et. al. Standards Track [Page 87]
RFC 2024 DLSw MIB using SMIv2 October 1996
NOTIFICATIONS {
dlswTrapTConnPartnerReject,
dlswTrapTConnProtViolation,
dlswTrapTConnUp,
dlswTrapTConnDown,
dlswTrapCircuitUp,
dlswTrapCircuitDown
}
STATUS current
DESCRIPTION
"Conformance group for DLSw notifications."
::= { dlswGroups 17 }
END
Chen, et. al. Standards Track [Page 88]
RFC 2024 DLSw MIB using SMIv2 October 1996
4.0 Acknowledgements
This memo has been produced by the AIW DLSw MIB RIGlet, which is also
recognized as the IETF DLSw MIB Working Group.
5.0 References
[1] Bartky, A., "Data Link Switching: Switch-to-Switch Protocol; AIW
DLSw RIG: DLSw Closed Pages, DLSw Standard Version 1", RFC 1795,
Sync Research Inc., April 1995.
[2] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Structure of Management Information for version 2 of
the Simple Network Management Protocol (SNMPv2)", RFC 1902, January
1996.
[3] Rose, M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", STD 16, RFC
1155, Performance Systems International, Hughes LAN Systems, May
1990.
[4] McCloghrie, K., and M. Rose, "Management Information Base for
Network Management of TCP/IP-based internets - MIB-II", STD 17, RFC
1213, Hughes LAN Systems, Performance Systems International, March
1991.
[5] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network
Management Protocol", STD 15, RFC 1157, SNMP Research, Performance
Systems International, Performance Systems International, MIT
Laboratory for Computer Science, May 1990.
[6] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Protocol Operations for version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1905, January 1996.
[7] IEEE Project, "ANSI/IEEE P802.1D", 1993
[8] McCloghrie, K., and F. Kastenholz, "Evolution of the Interfaces
Group of MIB-II", RFC 1573, Hughes LAN Systems, FTP Software,
January 1994.
[9] Hilgeman, J., S. Nix, A. Bartky, and W. Clark, "Definitions of
Managed Objects for SNA Data Link Control (SDLC) using SMIv2", RFC
1747, Apertus Technologies, Inc., Metaplex, Inc., Sync Research,
Inc., cisco Systems, Inc., January 1995
Chen, et. al. Standards Track [Page 89]
RFC 2024 DLSw MIB using SMIv2 October 1996
6.0 Security Considerations
Security issues are not discussed in this memo.
7.0 Authors' Addresses
David D. Chen
IBM Networking Systems
P. O. Box 12195
Research Triangle Park, NC 27709
US
Phone: +1 919 254 6182
EMail: dchen@vnet.ibm.com
Peter W. Gayek
IBM Networking Systems
P. O. Box 12195
Research Triangle Park, NC 27709
US
Phone: +1 919 254 1808
EMail: gayek@vnet.ibm.com
Shannon Nix
Metaplex, Inc.
7025 Kit Creek Road
P. O. Box 14987
Research Triangle Park, NC 27709
US
Phone: +1 919 472 2388
EMail: snix@metaplex.com
Chen, et. al. Standards Track [Page 90]