💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc6617.txt captured on 2022-06-04 at 01:07:06.

View Raw

More Information

⬅️ Previous capture (2021-11-30)

-=-=-=-=-=-=-







Internet Engineering Task Force (IETF)                        D. Harkins
Request for Comments: 6617                                Aruba Networks
Category: Experimental                                         June 2012
ISSN: 2070-1721


               Secure Pre-Shared Key (PSK) Authentication
              for the Internet Key Exchange Protocol (IKE)

Abstract

   This memo describes a secure pre-shared key (PSK) authentication
   method for the Internet Key Exchange Protocol (IKE).  It is resistant
   to dictionary attack and retains security even when used with weak
   pre-shared keys.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for examination, experimental implementation, and
   evaluation.

   This document defines an Experimental Protocol for the Internet
   community.  This document is a product of the Internet Engineering
   Task Force (IETF).  It represents the consensus of the IETF
   community.  It has received public review and has been approved for
   publication by the Internet Engineering Steering Group (IESG).  Not
   all documents approved by the IESG are a candidate for any level of
   Internet Standard; see Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc6617.

Copyright Notice

   Copyright (c) 2012 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.



Harkins                       Experimental                      [Page 1]

RFC 6617            Secure PSK Authentication for IKE          June 2012


Table of Contents

   1. Introduction ....................................................3
      1.1. Keyword Definitions ........................................3
   2. Usage Scenarios .................................................3
   3. Terms and Notation ..............................................4
   4. Discrete Logarithm Cryptography .................................5
      4.1. Elliptic Curve Cryptography (ECP) Groups ...................5
      4.2. Finite Field Cryptography (MODP) Groups ....................7
   5. Random Numbers ..................................................8
   6. Using Passwords and Raw Keys For Authentication .................8
   7. Assumptions .....................................................9
   8. Secure PSK Authentication Message Exchange ......................9
      8.1. Negotiation of Secure PSK Authentication ..................10
      8.2. Fixing the Secret Element, SKE ............................11
           8.2.1. ECP Operation to Select SKE ........................12
           8.2.2. MODP Operation to Select SKE .......................13
      8.3. Encoding and Decoding of Group Elements and Scalars .......14
           8.3.1. Encoding and Decoding of Scalars ...................14
           8.3.2. Encoding and Decoding of ECP Elements ..............15
           8.3.3. Encoding and Decoding of MODP Elements .............15
      8.4. Message Generation and Processing .........................16
           8.4.1. Generation of a Commit .............................16
           8.4.2. Processing of a Commit .............................16
                  8.4.2.1. Validation of an ECP Element ..............16
                  8.4.2.2. Validation of a MODP Element ..............16
                  8.4.2.3. Commit Processing Steps ...................17
           8.4.3. Authentication of the Exchange .....................17
      8.5. Payload Format ............................................18
           8.5.1. Commit Payload .....................................18
      8.6. IKEv2 Messaging ...........................................19
   9. IANA Considerations ............................................20
   10. Security Considerations .......................................20
   11. Acknowledgements ..............................................22
   12. References ....................................................22
      12.1. Normative References .....................................22
      12.2. Informative References ...................................23














Harkins                       Experimental                      [Page 2]

RFC 6617            Secure PSK Authentication for IKE          June 2012


1.  Introduction

   [RFC5996] allows for authentication of the IKE peers using a pre-
   shared key.  This exchange, though, is susceptible to dictionary
   attack and is therefore insecure when used with weak pre-shared keys,
   such as human-memorizable passwords.  To address the security issue,
   [RFC5996] recommends that the pre-shared key used for authentication
   "contain as much unpredictability as the strongest key being
   negotiated".  That means any non-hexadecimal key would require over
   100 characters to provide enough strength to generate a 128-bit key
   suitable for AES.  This is an unrealistic requirement because humans
   have a hard time entering a string over 20 characters without error.
   Consequently, pre-shared key authentication in [RFC5996] is used
   insecurely today.

   A pre-shared key authentication method built on top of a zero-
   knowledge proof will provide resistance to dictionary attack and
   still allow for security when used with weak pre-shared keys, such as
   user-chosen passwords.  Such an authentication method is described in
   this memo.

   Resistance to dictionary attack is achieved when an adversary gets
   one, and only one, guess at the secret per active attack (see, for
   example, [BM92], [BMP00], and [BPR00]).  Another way of putting this
   is that any advantage the adversary can realize is through
   interaction and not through computation.  This is demonstrably
   different than the technique from [RFC5996] of using a large, random
   number as the pre-shared key.  That can only make a dictionary attack
   less likely to succeed; it does not prevent a dictionary attack.
   Furthermore, as [RFC5996] notes, it is completely insecure when used
   with weak keys like user-generated passwords.

1.1.  Keyword Definitions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

2.  Usage Scenarios

   [RFC5996] describes usage scenarios for IKEv2.  These are:

   1.  "Security Gateway to Security Gateway Tunnel": The endpoints of
       the IKE (and IPsec) communication are network nodes that protect
       traffic on behalf of connected networks.  Protected traffic is
       between devices on the respective protected networks.





Harkins                       Experimental                      [Page 3]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   2.  "Endpoint-to-Endpoint Transport": The endpoints of the IKE (and
       IPsec) communication are hosts according to [RFC4301].  Protected
       traffic is between the two endpoints.

   3.  "Endpoint to Security Gateway Tunnel": One endpoint connects to a
       protected network through a network node.  The endpoints of the
       IKE (and IPsec) communication are the endpoint and network node,
       but the protected traffic is between the endpoint and another
       device on the protected network behind the node.

   The authentication and key exchange process described in this memo is
   suitable for all the usage scenarios described in [RFC5996].  In the
   "Security Gateway to Security Gateway Tunnel" scenario and the
   "Endpoint-to-Endpoint Transport" scenario, it provides a secure
   method of authentication without requiring a certificate.  For the
   "Endpoint to Security Gateway Tunnel" scenario, it provides for
   secure username+password authentication that is popular in remote-
   access VPN situations.

3.  Terms and Notation

   The following terms and notations are used in this memo:

   PSK
       A shared, secret, and potentially low-entropy word, phrase, code,
       or key used as a credential to mutually authenticate the peers.

   a = prf(b, c)
       The string "b" and "c" are given to a pseudo-random function
       (prf) to produce a fixed-length output "a".

   a | b
       denotes concatenation of string "a" with string "b".

   [a]b
       indicates a string consisting of the single bit "a" repeated "b"
       times.

   len(a)
       indicates the length in bits of the string "a".

   LSB(a)
       returns the least-significant bit of the bitstring "a".

   element
       one member of a finite cyclic group.





Harkins                       Experimental                      [Page 4]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   scalar
       a quantity that can multiply an element.

   The convention for this memo to represent an element in a finite
   cyclic group is to use an upper-case letter or acronym, while a
   scalar is indicated with a lowercase letter or acronym.

4.  Discrete Logarithm Cryptography

   This protocol uses Discrete Logarithm Cryptography to achieve
   authentication.  Each party to the exchange derives ephemeral public
   and private keys with respect to a particular set of domain
   parameters (referred to here as a "group").  Groups can be either
   based on finite field cryptography (modular exponentiation (MODP)
   groups) or elliptic curve cryptography (ECP groups).

   This protocol uses the same group as the IKE exchange in which it is
   being used for authentication, with the exception of characteristic-
   two elliptic curve groups (EC2N).  Use of such groups is undefined
   for this authentication method, and an IKE exchange that negotiates
   one of these groups MUST NOT use this method of authentication.

   For each group, the following operations are defined:

   o  "scalar operation" -- takes a scalar and an element in the group
      to produce another element -- Z = scalar-op(x, Y).

   o  "element operation" -- takes two elements in the group to produce
      a third -- Z = element-op(X, Y).

   o  "inverse operation" -- takes an element and returns another
      element such that the element operation on the two produces the
      identity element of the group -- Y = inverse(X).

4.1.  Elliptic Curve Cryptography (ECP) Groups

   The key exchange defined in this memo uses fundamental algorithms of
   ECP groups as described in [RFC6090].

   Domain parameters for ECP elliptic curves used for Secure PSK
   Authentication include:

   o  A prime, p, determining a prime field GF(p).  The cryptographic
      group will be a subgroup of the full elliptic curve group that
      consists of points on an elliptic curve -- elements from GF(p)
      that satisfy the curve's equation -- together with the "point at
      infinity" (denoted here as "0") that serves as the identity
      element.



Harkins                       Experimental                      [Page 5]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   o  Elements a and b from GF(p) that define the curve's equation.  The
      point (x,y) is on the elliptic curve if and only if y^2 = x^3 +
      a*x + b.

   o  A prime, r, which is the order of, or number of elements in, a
      subgroup generated by an element G.

   The scalar operation is multiplication of a point on the curve by
   itself a number of times.  The point Y is multiplied x-times to
   produce another point Z:

       Z = scalar-op(x, Y) = x*Y

   The element operation is addition of two points on the curve.  Points
   X and Y are summed to produce another point Z:

       Z = element-op(X, Y) = X + Y

   The inverse function is defined such that the sum of an element and
   its inverse is "0", the point-at-infinity of an elliptic curve group:

       Q + inverse(Q) = "0"

   Elliptic curve groups require a mapping function, q = F(Q), to
   convert a group element to an integer.  The mapping function used in
   this memo returns the x-coordinate of the point it is passed.

   scalar-op(x, Y) can be viewed as x iterations of element-op() by
   defining:

       Y = scalar-op(1, Y)

       Y = scalar-op(x, Y) = element-op(Y, scalar-op(x-1, Y)), for x > 1

   A definition of how to add two points on an elliptic curve (i.e.,
   element-op(X, Y)) can be found in [RFC6090].

   Note: There is another ECP domain parameter, a cofactor, h, that is
   defined by the requirement that the size of the full elliptic curve
   group (including "0") be the product of h and r.  ECP groups used for
   Secure PSK Authentication MUST have a cofactor of one (1).  At the
   time of publication of this memo, all ECP groups in [IKEV2-IANA] had
   a cofactor of one (1).








Harkins                       Experimental                      [Page 6]

RFC 6617            Secure PSK Authentication for IKE          June 2012


4.2.  Finite Field Cryptography (MODP) Groups

   Domain parameters for MODP groups used for Secure PSK Authentication
   include:

   o  A prime, p, determining a prime field GF(p), the integers modulo
      p.

   o  A prime, r, which is the multiplicative order, and thus also the
      size, of the cryptographic subgroup of GF(p)* that is generated by
      an element G.

   The scalar operation is exponentiation of a generator modulo a prime.
   An element Y is taken to the x-th power modulo the prime, thereby
   returning another element, Z:

       Z = scalar-op(x, Y) = Y^x mod p

   The element operation is modular multiplication.  Two elements, X and
   Y, are multiplied modulo the prime, thereby returning another
   element, Z:

       Z = element-op(X, Y) = (X * Y) mod p

   The inverse function for a MODP group is defined such that the
   product of an element and its inverse modulo the group prime equals
   one (1).  In other words,

       (Q * inverse(Q)) mod p = 1

   Unlike ECP groups, MODP groups do not require a mapping function to
   convert an element into an integer.  However, for the purposes of
   notation in protocol definition, the function F, when used below,
   shall just return the value that was passed to it, i.e., F(i) = i.

   Some MODP groups in [IKEV2-IANA] are based on safe primes, and the
   order is not included in the group's domain parameter set.  In this
   case only, the order, r, MUST be computed as the prime minus one
   divided by two -- (p-1)/2.  If an order is included in the group's
   domain parameter set, that value MUST be used in this exchange when
   an order is called for.  If a MODP group does not include an order in
   its domain parameter set and is not based on a safe prime, it MUST
   NOT be used with this exchange.








Harkins                       Experimental                      [Page 7]

RFC 6617            Secure PSK Authentication for IKE          June 2012


5.  Random Numbers

   As with IKE itself, the security of the Secure PSK Authentication
   method relies upon each participant in the protocol producing quality
   secret random numbers.  A poor random number chosen by either side in
   a single exchange can compromise the shared secret from that exchange
   and open up the possibility of a dictionary attack.

   Producing quality random numbers without specialized hardware entails
   using a cryptographic mixing function (like a strong hash function)
   to mix entropy from multiple, uncorrelated sources of information and
   events.  A very good discussion of this can be found in [RFC4086].

6.  Using Passwords and Raw Keys For Authentication

   The PSK used as an authentication credential with this protocol can
   be either a character-based password or passphrase, or it could be a
   binary or hexadecimal string.  Regardless, however, this protocol
   requires both the Initiator and Responder to have identical binary
   representations of the shared credential.

   If the PSK is a character-based password or passphrase, there are two
   types of pre-processing that SHALL be employed to convert the
   password or passphrase into a hexadecimal string suitable for use
   with Secure PSK Authentication.  If a PSK is already a hexadecimal or
   binary string, it SHALL be used directly as the shared credential
   without any pre-processing.

   The first step of pre-processing is to remove ambiguities that may
   arise due to internationalization.  Each character-based password or
   passphrase MUST be pre-processed to remove that ambiguity by
   processing the character-based password or passphrase according to
   the rules of the SASLprep [RFC4013] profile of [RFC3454].  The
   password or passphrase SHALL be considered a "stored string" per
   [RFC3454], and unassigned code points are therefore prohibited.  The
   output SHALL be the binary representation of the processed UTF-8
   character string.  Prohibited output and unassigned codepoints
   encountered in SASLprep pre-processing SHALL cause a failure of pre-
   processing, and the output SHALL NOT be used with Secure PSK
   Authentication.

   The next pre-processing step for character-based passwords or
   passphrases is to effectively obfuscate the string.  This is done in
   an attempt to reduce exposure of stored passwords in the event of
   server compromise, or compromise of a server's database of stored
   passwords.  The step involves taking the output of the SASLprep
   [RFC4013] profile of [RFC3454] and passing it, as the key, with the




Harkins                       Experimental                      [Page 8]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   ASCII string "IKE Secure PSK Authentication", as the data, to HMAC-
   SHA256().  The output of this obfuscation step SHALL become the
   shared credential used with Secure PSK Authentication.

   Note: Passwords tend to be shared for multiple purposes, and
   compromise of a server or database of stored plaintext passwords can
   be used, in that event, to mount multiple attacks.  The obfuscation
   step is merely to hide the password in the event of server compromise
   or compromise of the database of stored passwords.  Advances in
   distributed computing power have diminished the effectiveness of
   performing multiple prf iterations as a technique to prevent
   dictionary attacks, so no such behavior is proscribed here.  Mutually
   consenting implementations can agree to use a different password
   obfuscation method; the one described here is for interoperability
   purposes only.

   If a device stores passwords for use at a later time, it SHOULD pre-
   process the password prior to storage.  If a user enters a password
   into a device at authentication time, it MUST be pre-processed upon
   entry and prior to use with Secure PSK Authentication.

7.  Assumptions

   The security of the protocol relies on certain assumptions.  They
   are:

   1.  The pseudo-random function, prf, defined in [RFC5996], acts as an
       "extractor" (see [RFC5869]) by distilling the entropy from a
       secret input into a short, fixed string.  The output of prf is
       indistinguishable from a random source.

   2.  The discrete logarithm problem for the chosen finite cyclic group
       is hard.  That is, given G, p and Y = G^x mod p, it is
       computationally infeasible to determine x.  Similarly, for an
       elliptic curve group given the curve definition, a generator G,
       and Y = x * G, it is computationally infeasible to determine x.

   3.  The pre-shared key is drawn from a finite pool of potential keys.
       Each possible key in the pool has equal probability of being the
       shared key.  All potential adversaries have access to this pool
       of keys.

8.  Secure PSK Authentication Message Exchange

   The key exchange described in this memo is based on the "Dragonfly"
   key exchange, which has also been defined for use in 802.11 wireless
   networks (see [SAE]) and as an Extensible Authentication Protocol
   (EAP) method (see [RFC5931]).  "Dragonfly" is patent-free and



Harkins                       Experimental                      [Page 9]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   royalty-free.  It SHALL use the same pseudo-random function (prf) and
   the same Diffie-Hellman group that are negotiated for use in the IKE
   exchange that "Dragonfly" is authenticating.

   A pseudo-random function that uses a block cipher is NOT RECOMMENDED
   for use with Secure PSK Authentication due to its poor job operating
   as an "extractor" (see Section 7).  Pseudo-random functions based on
   hash functions using the HMAC construct from [RFC2104] SHOULD be
   used.

   To perform Secure PSK Authentication, each side must generate a
   shared and secret element in the chosen group based on the pre-shared
   key.  This element, called the Secret Key Element, or SKE, is then
   used in the "Dragonfly" authentication and key exchange protocol.
   "Dragonfly" consists of each side exchanging a Commit payload and
   then proving knowledge of the resulting shared secret.

   The Commit payload contributes ephemeral information to the exchange
   and binds the sender to a single value of the pre-shared key from the
   pool of potential pre-shared keys.  An authentication payload (AUTH)
   proves that the pre-shared key is known and completes the zero-
   knowledge proof.

8.1.  Negotiation of Secure PSK Authentication

   The Initiator indicates its desire to use Secure PSK Authentication
   by adding a Notify payload of type SECURE_PASSWORD_METHODS (see
   [RFC6467]) to the first message of the IKE_SA_INIT exchange and by
   including 3 in the notification data field of the Notify payload,
   indicating Secure PSK Authentication.

   The Responder indicates its acceptance to perform Secure PSK
   Authentication by adding a Notify payload of type
   SECURE_PASSWORD_METHODS to its response in the IKE_SA_INIT exchange
   and by adding the sole value of 3 to the notification data field of
   the Notify payload.

   If the Responder does not include a Notify payload of type
   SECURE_PASSWORD_METHODS in its IKE_SA_INIT response, the Initiator
   MUST terminate the exchange, and it MUST NOT fall back to the PSK
   authentication method of [RFC5996].  If the Initiator only indicated
   its support for Secure PSK Authentication (i.e., if the Notify data
   field only contained 3) and the Responder replies with a Notify
   payload of type SECURE_PASSWORD_METHODS and a different value in the
   Notify data field, the Initiator MUST terminate the exchange.






Harkins                       Experimental                     [Page 10]

RFC 6617            Secure PSK Authentication for IKE          June 2012


8.2.  Fixing the Secret Element, SKE

   The method of fixing SKE depends on the type of group, either MODP or
   ECP.  The function "prf+" from [RFC5996] is used as a key derivation
   function.

   Fixing SKE involves an iterative hunting-and-pecking technique using
   the prime from the negotiated group's domain parameter set and an
   ECP- or MODP-specific operation depending on the negotiated group.
   This technique requires the pre-shared key to be a binary string;
   therefore, any pre-processing transformation (see Section 6) MUST be
   performed on the pre-shared key prior to fixing SKE.

   To thwart side-channel attacks that attempt to determine the number
   of iterations of the hunting-and-pecking loop that are used to find
   SKE for a given password, a security parameter, k, is used to ensure
   that at least k iterations are always performed.

   Prior to beginning the hunting-and-pecking loop, an 8-bit counter is
   set to the value one (1).  Then the loop begins.  First, the pseudo-
   random function is used to generate a secret seed using the counter,
   the pre-shared key, and two nonces (without the fixed headers)
   exchanged by the Initiator and the Responder (see Section 8.6):

      ske-seed = prf(Ni | Nr, psk | counter)

   Then, the ske-seed is expanded using prf+ to create an ske-value:

      ske-value = prf+(ske-seed, "IKE SKE Hunting And Pecking")

   where len(ske-value) is the same as len(p), the length of the prime
   from the domain parameter set of the negotiated group.

   If the ske-seed is greater than or equal to the prime, p, the counter
   is incremented, a new ske-seed is generated, and the hunting-and-
   pecking continues.  If ske-seed is less than the prime, p, it is
   passed to the group-specific operation to select the SKE or fail.  If
   the group-specific operation fails, the counter is incremented, a new
   ske-seed is generated, and the hunting-and-pecking continues.  This
   process continues until the group-specific operation returns the
   password element.  After the password element has been chosen, a
   random number is used in place of the password in the ske-seed
   calculation, and the hunting-and-pecking continues until the counter
   is greater than the security parameter, k.







Harkins                       Experimental                     [Page 11]

RFC 6617            Secure PSK Authentication for IKE          June 2012


8.2.1.  ECP Operation to Select SKE

   The group-specific operation for ECP groups uses ske-value, ske-seed,
   and the equation of the curve to produce SKE.  First, ske-value is
   used directly as the x-coordinate, x, with the equation of the
   elliptic curve, with parameters a and b from the domain parameter set
   of the curve, to solve for a y-coordinate, y.

   Note: A method of checking whether a solution to the equation of the
   elliptic curve is to see whether the Legendre symbol of (x^3 + ax +
   b) equals one (1).  If it does, then a solution exists; if it does
   not, then there is no solution.

   If there is no solution to the equation of the elliptic curve, then
   the operation fails, the counter is incremented, a new ske-value and
   ske-seed are selected, and the hunting-and-pecking continues.  If
   there is a solution then, y is calculated as the square root of (x^3
   + ax + b) using the equation of the elliptic curve.  In this case, an
   ambiguity exists as there are technically two solutions to the
   equation, and ske-seed is used to unambiguously select one of them.
   If the low-order bit of ske-seed is equal to the low-order bit of y,
   then a candidate SKE is defined as the point (x,y); if the low-order
   bit of ske-seed differs from the low-order bit of y then a candidate
   SKE is defined as the point (x, p-y) where p is the prime from the
   negotiated group's domain parameter set.  The candidate SKE becomes
   the SKE, and the ECP-specific operation completes successfully.

























Harkins                       Experimental                     [Page 12]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   Algorithmically, the process looks like this:

         found = 0
         counter = 1
         v = psk
         do {
           ske-seed = prf(Ni | Nr, v | counter)
           ske-value = prf+(ske-seed, "IKE SKE Hunting And Pecking")
           if (ske-value < p)
           then
             x = ske-value
             if ( (y = sqrt(x^3 + ax + b)) != FAIL)
             then
               if (found == 0)
               then
                 if (LSB(y) == LSB(ske-seed))
                 then
                   SKE = (x,y)
                 else
                   SKE = (x, p-y)
                 fi
                 found = 1
                 v = random()
               fi
             fi
           fi
           counter = counter + 1
         } while ((found == 0) || (counter <= k))

   where FAIL indicates that there is no solution to sqrt(x^3 + ax + b).

                    Figure 1: Fixing SKE for ECP Groups

   Note: For ECP groups, the probability that more than "n" iterations
   of the hunting-and-pecking loop are required to find SKE is roughly
   (1-(r/2p))^n, which rapidly approaches zero (0) as "n" increases.

8.2.2.  MODP Operation to Select SKE

   The group-specific operation for MODP groups takes ske-value, the
   prime, p, and order, r, from the group's domain parameter set to
   directly produce a candidate SKE by exponentiating the ske-value to
   the value ((p-1)/r) modulo the prime.  If the candidate SKE is
   greater than one (1), the candidate SKE becomes the SKE, and the
   MODP-specific operation completes successfully.  Otherwise, the MODP-
   specific operation fails (and the hunting-and-pecking continues).





Harkins                       Experimental                     [Page 13]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   Algorithmically, the process looks like this:

         found = 0
         counter = 1
         v = psk
         do {
           ske-seed = prf(Ni | Nr, v | counter)
           ske-value = prf+(ske-seed, "IKE SKE Hunting And Pecking")
           if (ske-value < p)
           then
             ELE = ske-value ^ ((p-1)/r) mod p
             if (ELE > 1)
             then
               if (found == 0)
                 SKE = ELE
                 found = 1
                 v = random()
               fi
             fi
           fi
           counter = counter + 1
         } while ((found == 0) || (counter <= k))

                   Figure 2: Fixing SKE for MODP Groups

   Note: For MODP groups, the probability that more than "n" iterations
   of the hunting-and-pecking loop are required to find SKE is roughly
   ((m-p)/p)^n, where m is the largest unsigned number that can be
   expressed in len(p) bits, which rapidly approaches zero (0) as "n"
   increases.

8.3.  Encoding and Decoding of Group Elements and Scalars

   The payloads used in the Secure PSK Authentication method contain
   elements from the negotiated group and scalar values.  To ensure
   interoperability, scalars and field elements MUST be represented in
   payloads in accordance with the requirements in this section.

8.3.1.  Encoding and Decoding of Scalars

   Scalars MUST be represented (in binary form) as unsigned integers
   that are strictly less than r, the order of the generator of the
   agreed-upon cryptographic group.  The binary representation of each
   scalar MUST have a bit length equal to the bit length of the binary
   representation of r.  This requirement is enforced, if necessary, by
   prepending the binary representation of the integer with zeros until
   the required length is achieved.




Harkins                       Experimental                     [Page 14]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   Scalars in the form of unsigned integers are converted into octet
   strings and back again using the technique described in [RFC6090].

8.3.2.  Encoding and Decoding of ECP Elements

   Elements in ECP groups are points on the negotiated elliptic curve.
   Each such element MUST be represented by the concatenation of two
   components, an x-coordinate and a y-coordinate.

   Each of the two components, the x-coordinate and the y-coordinate,
   MUST be represented (in binary form) as an unsigned integer that is
   strictly less than the prime, p, from the group's domain parameter
   set.  The binary representation of each component MUST have a bit
   length equal to the bit length of the binary representation of p.
   This length requirement is enforced, if necessary, by prepending the
   binary representation of the integer with zeros until the required
   length is achieved.

   The unsigned integers that represent the coordinates of the point are
   converted into octet strings and back again using the technique
   described in [RFC6090].

   Since the field element is represented in a payload by the
   x-coordinate followed by the y-coordinate, it follows, then, that the
   length of the element in the payload MUST be twice the bit length of
   p.

8.3.3.  Encoding and Decoding of MODP Elements

   Elements in MODP groups MUST be represented (in binary form) as
   unsigned integers that are strictly less than the prime, p, from the
   group's domain parameter set.  The binary representation of each
   group element MUST have a bit length equal to the bit length of the
   binary representation of p.  This length requirement is enforced, if
   necessary, by prepending the binary representation of the integer
   with zeros until the required length is achieved.

   The unsigned integer that represents a MODP element is converted into
   an octet string and back using the technique described in [RFC6090].












Harkins                       Experimental                     [Page 15]

RFC 6617            Secure PSK Authentication for IKE          June 2012


8.4.  Message Generation and Processing

8.4.1.  Generation of a Commit

   Before a Commit payload can be generated, the SKE must be fixed using
   the process described in Section 8.2.

   A Commit payload has two components, a scalar and an element.  To
   generate a Commit payload, two random numbers, a "private" value and
   a "mask" value, are generated (see Section 5).  Their sum modulo the
   order of the group, r, becomes the scalar component:

       scalar = (private + mask) mod r

   If the scalar is not greater than one (1), the private and mask
   values MUST be thrown away, and new values randomly generated.  If
   the scalar is greater than one (1), the inverse of the scalar
   operation with the mask and SKE becomes the element component.

       Element = inverse(scalar-op(mask, SKE))

   The Commit payload consists of the scalar followed by the element,
   and the scalar and element are encoded in the Commit payload
   according to Section 8.3.

8.4.2.  Processing of a Commit

   Upon receipt of a peer's Commit payload, the scalar and element MUST
   be validated.  The processing of an element depends on the type,
   either an ECP element or a MODP element.

8.4.2.1.  Validation of an ECP Element

   Validating a received ECP element involves: 1) checking whether the
   two coordinates, x and y, are both greater than zero (0) and less
   than the prime defining the underlying field; and 2) checking whether
   the x- and y-coordinates satisfy the equation of the curve (that is,
   that they produce a valid point on the curve that is not "0").  If
   either of these conditions are not met, the received element is
   invalid; otherwise, the received element is valid.

8.4.2.2.  Validation of a MODP Element

   A received MODP element is valid if: 1) it is between one (1) and the
   prime, p, exclusive; and 2) if modular exponentiation of the element
   by the group order, r, equals one (1).  If either of these conditions
   are not true, the received element is invalid; otherwise, the
   received element is valid.



Harkins                       Experimental                     [Page 16]

RFC 6617            Secure PSK Authentication for IKE          June 2012


8.4.2.3.  Commit Processing Steps

   Commit payload validation is accomplished by the following steps:

   1.  The length of the Commit payload is checked against its
       anticipated length (the anticipated length of the scalar plus the
       anticipated length of the element, for the negotiated group).  If
       it is incorrect, the Commit payload is invalidated; otherwise,
       processing continues.

   2.  The peer's scalar is extracted from the Commit payload according
       to Section 8.3.1 and checked to ensure it is between one (1) and
       r, the order of the negotiated group, exclusive.  If it is not,
       the Commit payload is invalidated; otherwise, processing
       continues.

   3.  The peer's element is extracted from the Commit payload according
       to Section 8.3.2 and checked in a manner that depends on the type
       of group negotiated.  If the group is ECP, the element is
       validated according to Section 8.4.2.1.  If the group is MODP,
       the element is validated according to Section 8.4.2.2.  If the
       element is not valid, then the Commit payload is invalidated;
       otherwise, the Commit payload is validated.

   4.  The Initiator of the IKE exchange has an added requirement to
       verify that the received element and scalar from the Commit
       payload differ from the element and scalar sent to the Responder.
       If they are identical, it signifies a reflection attack, and the
       Commit payload is invalidated.

   If the Commit payload is invalidated, the payload MUST be discarded
   and the IKE exchange aborted.

8.4.3.  Authentication of the Exchange

   After a Commit payload has been generated and a peer's Commit payload
   has been processed, a shared secret used to authenticate the peer is
   derived.  Using SKE, the "private" value generated as part of Commit
   payload generation, and the peer's scalar and element from the peer's
   Commit payload, named here peer-scalar and Peer-Element,
   respectively, a preliminary shared secret, skey, is generated as:

        skey = F(scalar-op(private,
                           element-op(Peer-Element,
                                      scalar-op(peer-scalar, SKE))))






Harkins                       Experimental                     [Page 17]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   For the purposes of subsequent computation, the bit length of skey
   SHALL be equal to the bit length of the prime, p, used in either a
   MODP or ECP group.  This bit length SHALL be enforced, if necessary,
   by prepending zeros to the value until the required length is
   achieved.

   A shared secret, ss, is then computed from skey and the nonces
   exchanged by the Initiator (Ni) and Responder (Nr) (without the fixed
   headers) using prf():

        ss = prf(Ni | Nr, skey | "Secure PSK Authentication in IKE")

   The shared secret, ss, is used in an AUTH authentication payload to
   prove possession of the shared secret and therefore knowledge of the
   pre-shared key.

8.5.  Payload Format

8.5.1.  Commit Payload

   [RFC6467] defines a Generic Secure Password Method (GSPM) payload
   that is used to convey information that is specific to a particular
   secure password method.  This memo uses the GSPM payload as a Commit
   payload to contain the scalar and element used in the Secure PSK
   Authentication exchange:

   The Commit payload is defined as follows:

                            1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       ! Next Payload  !C!  RESERVED   !         Payload Length        !
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                                                               |
       +                            scalar                             ~
       |                                                               |
       ~                               +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                               |                               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                               ~
       |                                                               |
       ~                           Element                             ~
       |                                                               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The scalar and element SHALL be encoded in the Commit payload
   according to Section 8.3.





Harkins                       Experimental                     [Page 18]

RFC 6617            Secure PSK Authentication for IKE          June 2012


8.6.  IKEv2 Messaging

   Secure PSK Authentication modifies the IKE_AUTH exchange by adding
   one additional round trip to exchange Commit payloads to perform the
   Secure PSK Authentication exchange and by changing the calculation of
   the AUTH payload data to bind the IKEv2 exchange to the outcome of
   the Secure PSK Authentication exchange (see Figure 3).

    Initiator                               Responder
   -----------                             -----------

   IKE_SA_INIT:

    HDR, SAi1, KEi, Ni,
         N(SPM-SPSK)  -->

                                  <--    HDR, SAr1, KEr, Nr,
                                              N(SPM-SPSK)

   IKE_AUTH:

    HDR, SK {IDi, COMi, [IDr,]
             SAi2, TSi, TSr}      -->
                                  <--    HDR, SK {IDr, COMr}
    HDR, SK {AUTHi}               -->
                                  <--    HDR, SK {AUTHr, SAr2, TSi, TSr}

   where N(SPM-SPSK) indicates the Secure Password Methods Notify
   payloads used to negotiate the use of Secure PSK Authentication (see
   Section 8.1), COMi and AUTHi are the Commit payload and AUTH payload,
   respectively, sent by the Initiator, and COMr and AUTHr are the
   Commit payload and AUTH payload, respectively, sent by the Responder.

                       Figure 3: Secure PSK in IKEv2

   When doing Secure PSK Authentication, the AUTH payloads SHALL be
   computed as

       AUTHi = prf(ss, <InitiatorSignedOctets> | COMi | COMr)

       AUTHr = prf(ss, <ResponderSignedOctets> | COMr | COMi)

   where "ss" is the shared secret derived in Section 8.4.3, COMi and
   COMr are the entire Commit payloads (including the fixed headers)
   sent by the Initiator and Responder, respectively, and
   <InitiatorSignedOctets> and <ResponderSignedOctets> are defined in





Harkins                       Experimental                     [Page 19]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   [RFC5996].  The Authentication Method indicated in both AUTH payloads
   SHALL be "Generic Secure Password Authentication Method", value 12,
   from [IKEV2-IANA].

9.  IANA Considerations

   IANA has assigned the value 3 for "Secure PSK Authentication" from
   the Secure Password Authentication Method registry in [IKEV2-IANA].

10.  Security Considerations

   Both the Initiator and Responder obtain a shared secret, "ss" (see
   Section 8.4.3), based on a secret group element and their own private
   values contributed to the exchange.  If they do not share the same
   pre-shared key, they will be unable to derive the same secret group
   element, and if they do not share the same secret group element, they
   will be unable to derive the same shared secret.

   Resistance to dictionary attack means that the adversary must launch
   an active attack to make a single guess at the pre-shared key.  If
   the size of the pool from which the key was extracted was d and each
   key in the pool has an equal probability of being chosen, then the
   probability of success after a single guess is 1/d.  After x guesses,
   and removal of failed guesses from the pool of possible keys, the
   probability becomes 1/(d-x).  As x grows, so does the probability of
   success.  Therefore, it is possible for an adversary to determine the
   pre-shared key through repeated brute-force, active, guessing
   attacks.  This authentication method does not presume to be secure
   against this, and implementations SHOULD ensure the value of d is
   sufficiently large to prevent this attack.  Implementations SHOULD
   also take countermeasures, for instance, refusing authentication
   attempts for a certain amount of time after the number of failed
   authentication attempts reaches a certain threshold.  No such
   threshold or amount of time is recommended in this memo.

   An active attacker can impersonate the Responder of the exchange and
   send a forged Commit payload after receiving the Initiator's Commit
   payload.  The attacker then waits until it receives the
   authentication payload from the Responder.  Now the attacker can
   attempt to run through all possible values of the pre-shared key,
   computing SKE (see Section 8.2), computing "ss" (see Section 8.4.3),
   and attempting to recreate the Confirm payload from the Responder.

   But, by sending a forged Commit payload the attacker commits to a
   single guess of the pre-shared key.  That value was used by the
   Responder in his computation of "ss", which was used in the
   authentication payload.  Any guess of the pre-shared key that differs
   from the one used in the forged Commit payload would result in each



Harkins                       Experimental                     [Page 20]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   side using a different secret element in the computation of "ss" and
   therefore the authentication payload could not be verified as
   correct, even if a subsequent guess, while running through all
   possible values, was correct.  The attacker gets one guess, and one
   guess only, per active attack.

   An attacker, acting as either the Initiator or Responder, can take
   the element from the Commit payload received from the other party,
   reconstruct the random "mask" value used in its construction, and
   then recover the other party's "private" value from the scalar in the
   Commit payload.  But this requires the attacker to solve the discrete
   logarithm problem, which we assumed was intractable (Section 7).

   Instead of attempting to guess at pre-shared keys, an attacker can
   attempt to determine SKE and then launch an attack, but SKE is
   determined by the output of the pseudo-random function, prf, which is
   assumed to be indistinguishable from a random source (Section 7).
   Therefore, each element of the finite cyclic group will have an equal
   probability of being the SKE.  The probability of guessing SKE will
   be 1/r, where r is the order of the group.  This is the same
   probability of guessing the solution to the discrete logarithm, which
   is assumed to be intractable (Section 7).  The attacker would have a
   better chance of success at guessing the input to prf, i.e., the pre-
   shared key, since the order of the group will be many orders of
   magnitude greater than the size of the pool of pre-shared keys.

   The implications of resistance to dictionary attack are significant.
   An implementation can provision a pre-shared key in a practical and
   realistic manner -- i.e., it MAY be a character string, and it MAY be
   relatively short -- and still maintain security.  The nature of the
   pre-shared key determines the size of the pool, D, and
   countermeasures can prevent an adversary from determining the secret
   in the only possible way: repeated, active, guessing attacks.  For
   example, a simple four-character string using lowercase English
   characters, and assuming random selection of those characters, will
   result in D of over four hundred thousand.  An adversary would need
   to mount over one hundred thousand active, guessing attacks (which
   will easily be detected) before gaining any significant advantage in
   determining the pre-shared key.

   If an attacker knows the number of hunting-and-pecking loops that
   were required to determine SKE, it is possible to eliminate passwords
   from the pool of potential passwords and increase the probability of
   successfully guessing the real password.  MODP groups will require
   more than "n" loops with a probability based on the value of the
   prime -- if m is the largest unsigned number that can be expressed in
   len(p) bits, then the probability is ((m-p)/p)^n -- which will
   typically be very small for the groups defined in [IKEV2-IANA].  ECP



Harkins                       Experimental                     [Page 21]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   groups will require more than one "n" loop with a probability of
   roughly (1-(r/2p))^n.  Therefore, a security parameter, k, is defined
   that will ensure that at least k loops will always be executed
   regardless of whether SKE is found in less than k loops.  There is
   still a probability that a password would require more than k loops,
   and a side-channel attacker could use that information to his
   advantage, so selection of the value of k should be based on a trade-
   off between the additional workload to always perform k iterations
   and the potential of providing information to a side-channel
   attacker.  It is important to note that the possibility of a
   successful side-channel attack is greater against ECP groups than
   MODP groups, and it might be appropriate to have separate values of k
   for the two.

   For a more detailed discussion of the security of the key exchange
   underlying this authentication method, see [SAE] and [RFC5931].

11.  Acknowledgements

   The author would like to thank Scott Fluhrer and Hideyuki Suzuki for
   their insight in discovering flaws in earlier versions of the key
   exchange that underlies this authentication method and for their
   helpful suggestions in improving it.  Thanks to Lily Chen for useful
   advice on the hunting-and-pecking technique to "hash into" an element
   in a group and to Jin-Meng Ho for a discussion on countering a small
   sub-group attack.  Rich Davis suggested several checks on received
   messages that greatly increase the security of the underlying key
   exchange.  Hugo Krawczyk suggested using the prf as an extractor.

12.  References

12.1.  Normative References

   [IKEV2-IANA]  IANA, "IKEv2 Parameters",
                 <http://www.iana.org/assignments/ikev2-parameters>.

   [RFC2104]     Krawczyk, H., Bellare, M., and R. Canetti, "HMAC:
                 Keyed-Hashing for Message Authentication", RFC 2104,
                 February 1997.

   [RFC2119]     Bradner, S., "Key words for use in RFCs to Indicate
                 Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3454]     Hoffman, P. and M. Blanchet, "Preparation of
                 Internationalized Strings ("stringprep")", RFC 3454,
                 December 2002.





Harkins                       Experimental                     [Page 22]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   [RFC4013]     Zeilenga, K., "SASLprep: Stringprep Profile for User
                 Names and Passwords", RFC 4013, February 2005.

   [RFC5996]     Kaufman, C., Hoffman, P., Nir, Y., and P. Eronen,
                 "Internet Key Exchange Protocol Version 2 (IKEv2)",
                 RFC 5996, September 2010.

   [RFC6090]     McGrew, D., Igoe, K., and M. Salter, "Fundamental
                 Elliptic Curve Cryptography Algorithms", RFC 6090,
                 February 2011.

   [RFC6467]     Kivinen, T., "Secure Password Framework for Internet
                 Key Exchange Version 2 (IKEv2)", RFC 6467,
                 December 2011.

12.2.  Informative References

   [BM92]        Bellovin, S. and M. Merritt, "Encrypted Key Exchange:
                 Password-Based Protocols Secure Against Dictionary
                 Attacks", Proceedings of the IEEE Symposium on Security
                 and Privacy, Oakland, 1992.

   [BMP00]       Boyko, V., MacKenzie, P., and S. Patel, "Provably
                 Secure Password-Authenticated Key Exchange Using
                 Diffie-Hellman", Proceedings of Eurocrypt 2000, LNCS
                 1807 Springer-Verlag, 2000.

   [BPR00]       Bellare, M., Pointcheval, D., and P. Rogaway,
                 "Authenticated Key Exchange Secure Against Dictionary
                 Attacks", Advances in Cryptology -- Eurocrypt '00,
                 Lecture Notes in Computer Science Springer-Verlag,
                 2000.

   [RFC4086]     Eastlake, D., Schiller, J., and S. Crocker, "Randomness
                 Requirements for Security", BCP 106, RFC 4086,
                 June 2005.

   [RFC4301]     Kent, S. and K. Seo, "Security Architecture for the
                 Internet Protocol", RFC 4301, December 2005.

   [RFC5869]     Krawczyk, H. and P. Eronen, "HMAC-based Extract-and-
                 Expand Key Derivation Function (HKDF)", RFC 5869,
                 May 2010.

   [RFC5931]     Harkins, D. and G. Zorn, "Extensible Authentication
                 Protocol (EAP) Authentication Using Only a Password",
                 RFC 5931, August 2010.




Harkins                       Experimental                     [Page 23]

RFC 6617            Secure PSK Authentication for IKE          June 2012


   [SAE]         Harkins, D., "Simultaneous Authentication of Equals: A
                 Secure, Password-Based Key Exchange for Mesh Networks",
                 Proceedings of the 2008 Second International Conference
                 on Sensor Technologies and Applications Volume 00,
                 2008.

Author's Address

   Dan Harkins
   Aruba Networks
   1322 Crossman Avenue
   Sunnyvale, CA  94089-1113
   United States of America

   EMail: dharkins@arubanetworks.com




































Harkins                       Experimental                     [Page 24]