💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc6041.txt captured on 2022-04-28 at 20:55:40.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Internet Engineering Task Force (IETF) A. Crouch
Request for Comments: 6041 H. Khosravi
Category: Informational Intel
ISSN: 2070-1721 A. Doria, Ed.
LTU
X. Wang
Huawei
K. Ogawa
NTT Corporation
October 2010
Forwarding and Control Element Separation (ForCES)
Applicability Statement
Abstract
The Forwarding and Control Element Separation (ForCES) protocol
defines a standard framework and mechanism for the interconnection
between control elements and forwarding elements in IP routers and
similar devices. In this document we describe the applicability of
the ForCES model and protocol. We provide example deployment
scenarios and functionality, as well as document applications that
would be inappropriate for ForCES.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc6041.
Crouch, et al. Informational [Page 1]
RFC 6041 ForCES Applicability Statement October 2010
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Crouch, et al. Informational [Page 2]
RFC 6041 ForCES Applicability Statement October 2010
Table of Contents
1. Introduction ....................................................3
2. Purpose .........................................................4
3. Terminology .....................................................4
4. Applicability to IP Networks ....................................4
4.1. Applicable Services ........................................5
4.1.1. Association, Capability Discovery, and
Information Exchange ................................5
4.1.2. Topology Information Exchange .......................6
4.1.3. Configuration .......................................6
4.1.4. Routing Exchange ....................................6
4.1.5. QoS Capabilities Exchange and Configuration .........7
4.1.6. Security Exchange ...................................7
4.1.7. Filtering Exchange and Firewalls ....................7
4.1.8. Encapsulation/Tunneling Exchange ....................7
4.1.9. NAT and Application-Level Gateways ..................7
4.1.10. Measurement and Accounting .........................7
4.1.11. Diagnostics ........................................8
4.1.12. Redundancy and Failover ............................8
4.2. CE-FE Link Capability ......................................8
4.3. CE/FE Locality .............................................8
5. Security Considerations .........................................9
6. ForCES Manageability ............................................9
6.1. The NE as an Atomic Element ...............................10
6.2. The NE as Composed of Manageable Elements .................10
6.3. ForCES Protocol MIB .......................................10
6.3.1. MIB Management of an FE ............................11
6.4. The FEM and CEM ...........................................12
7. Contributors ...................................................12
8. Acknowledgments ................................................12
9. References .....................................................12
9.1. Normative References ......................................12
9.2. Informative References ....................................13
1. Introduction
The Forwarding and Control Element Separation (ForCES) protocol
defines a standard framework and mechanism for the exchange of
information between the logically separate functionality of the
control and data forwarding planes of IP routers and similar devices.
It focuses on the communication necessary for separation of control
plane functionality such as routing protocols, signaling protocols,
and admission control from data forwarding plane per-packet
activities such as packet forwarding, queuing, and header editing.
Crouch, et al. Informational [Page 3]
RFC 6041 ForCES Applicability Statement October 2010
This document defines the applicability of the ForCES mechanisms. It
describes types of configurations and settings where ForCES is most
appropriately applied. This document also describes scenarios and
configurations where ForCES would not be appropriate for use.
2. Purpose
The purpose of the ForCES Applicability Statement is to capture the
intent of the ForCES protocol [RFC5810] designers as to how the
protocol could be used in conjunction with the ForCES model [RFC5812]
and a Transport Mapping Layer [RFC5811].
3. Terminology
A set of concepts associated with ForCES was introduced in
"Requirements for Separation of IP Control and Forwarding" [RFC3654]
and in "Forwarding and Control Element Separation (ForCES) Framework"
[RFC3746]. The terminology associated with these concepts and with
the protocol elements in ForCES is defined in the "Forwarding and
Control Element Separation (ForCES) Protocol Specification"
[RFC5810].
The reader is directed to these documents for the conceptual
introduction and for definitions, including the following acronyms:
o CE: control element
o CEM: CE Manager
o FE: forwarding element
o FEM: FE Manager
o ForCES: Forwarding and Control Element Separation protocol
o LFB: Logical Function Block
o NE: ForCES network element
o TML: Transport Mapping Layer
4. Applicability to IP Networks
This section lists the areas of ForCES applicability in IP network
devices. Some relatively low-end routing systems may be implemented
on simple hardware that performs both control and packet forwarding
functionality. ForCES may not be useful for such devices.
Crouch, et al. Informational [Page 4]
RFC 6041 ForCES Applicability Statement October 2010
Higher-end routing systems typically distribute work amongst several
interface-processing elements, and these devices (FEs) therefore need
to communicate with the control element(s) to perform their job. A
higher-end router may also distribute control processing amongst
several processing elements (CEs). ForCES provides a standard way to
do this communication. ForCES also provides support for high-
availability configurations that include a primary CE and one or more
secondary CEs.
The remainder of this section lists the applicable services that
ForCES may support, applicable FE functionality, applicable CE-FE
link scenarios, and applicable topologies in which ForCES may be
deployed.
4.1. Applicable Services
In this section we describe the applicability of ForCES for the
following control-forwarding-plane services:
o Association, Capability Discovery, and Information Exchange
o Topology Information Exchange
o Configuration
o Routing Exchange
o Quality of Service (QoS) Exchange
o Security Exchange
o Filtering Exchange
o Encapsulation/Tunneling Exchange
o NAT and Application-Level Gateways
o Measurement and Accounting
o Diagnostics
o CE Redundancy or CE Failover
4.1.1. Association, Capability Discovery, and Information Exchange
Association is the first step of the ForCES protocol exchange in
which capability discovery and exchange happens between one or more
CEs and the FEs. ForCES assumes that CEs and FEs already have
Crouch, et al. Informational [Page 5]
RFC 6041 ForCES Applicability Statement October 2010
sufficient information to begin communication in a secure manner.
The ForCES protocol is only applicable after CEs and FEs have
discovered each other. ForCES makes no assumption about whether
discovery was performed using a dynamic protocol or merely static
configuration. Some discussion about how this can occur can be found
in Section 6.4 of this document.
During the association phase, CEs and FEs exchange capability
information with each other. For example, the FEs express the number
of interface ports they provide, as well as the static and
configurable attributes of each port.
In addition to initial configuration, the CEs and FEs also exchange
dynamic configuration changes using ForCES. For example, FEs
asynchronously inform the CEs of an increase/decrease in available
resources or capabilities on the FE.
4.1.2. Topology Information Exchange
In this context, topology information relates to how the FEs are
interconnected with each other with respect to packet forwarding.
Topology discovery is outside the scope of the ForCES protocol. An
implementation can choose its own method of topology discovery (for
example, it can use a standard topology discovery protocol or apply a
static topology configuration policy). Once the topology is
established, the ForCES protocol may be used to transmit the
resulting information to the CEs.
4.1.3. Configuration
ForCES is used to perform FE configuration. For example, CEs set
configurable FE attributes such as IP addresses, etc. for their
interfaces.
4.1.4. Routing Exchange
ForCES may be used to deliver packet forwarding information resulting
from CE routing calculations. For example, CEs may send forwarding
table updates to the FEs, so that they can make forwarding decisions.
FEs may inform the CEs in the event of a forwarding table miss.
ForCES may also be used to configure Equal Cost Multi-Path (ECMP)
capability.
Crouch, et al. Informational [Page 6]
RFC 6041 ForCES Applicability Statement October 2010
4.1.5. QoS Capabilities Exchange and Configuration
ForCES may be used to exchange QoS capabilities between CEs and FEs.
For example, an FE may express QoS capabilities to the CE. Such
capabilities might include metering, policing, shaping, and queuing
functions. The CE may use ForCES to configure these capabilities.
4.1.6. Security Exchange
ForCES may be used to exchange security information between a CE and
the FEs it controls. For example, the FE may use ForCES to express
the types of encryption that it is capable of using in an IP Security
(IPsec) tunnel. The CE may use ForCES to configure such a tunnel.
The CEs would be responsible for the NE dynamic key exchanges and
updates.
4.1.7. Filtering Exchange and Firewalls
ForCES may be used to exchange filtering information. For example,
FEs may use ForCES to express the filtering functions, such as
classification and action, that they can perform, and the CE may
configure these capabilities.
4.1.8. Encapsulation/Tunneling Exchange
ForCES may be used to exchange encapsulation capabilities of an FE,
such as tunneling, and the configuration of such capabilities.
4.1.9. NAT and Application-Level Gateways
ForCES may be used to exchange configuration information for Network
Address Translators. Whilst ForCES is not specifically designed for
the configuration of application-level gateway functionality, this
may be in scope for some types of application-level gateways.
4.1.10. Measurement and Accounting
ForCES may be used to exchange configuration information regarding
traffic measurement and accounting functionality. In this area,
ForCES may overlap somewhat with functionality provided by network
management mechanisms such as the Simple Network Management Protocol
(SNMP). In some cases, ForCES may be used to convey information to
the CE to be reported externally using SNMP. A further discussion of
this capability is covered in Section 6 of this document.
Crouch, et al. Informational [Page 7]
RFC 6041 ForCES Applicability Statement October 2010
4.1.11. Diagnostics
ForCES may be used for CEs and FEs to exchange diagnostic
information. For example, an FE can send self-test results to a CE.
4.1.12. Redundancy and Failover
The ForCES architecture includes mechanisms that allow for multiple
redundant CEs and FEs in a ForCES NE. The ForCES-model LFB
definitions provide sufficient component details via component
identifiers to be universally unique within an NE. The ForCES
protocol includes mechanisms to facilitate transactions as well as
atomicity across the NE.
Given the above, it is possible to deploy redundant CEs and FEs that
incorporate failover.
4.2. CE-FE Link Capability
When using ForCES, the bandwidth of the CE-FE link is a
consideration, and cannot be ignored. For example, sending a full
routing table is reasonable over a high-bandwidth link, but could be
non-trivial over a lower-bandwidth link. ForCES should be
sufficiently future-proof to be applicable in scenarios where routing
tables grow to several orders of magnitude greater than their current
size. However, we also note that not all IP routers need full
routing tables.
4.3. CE/FE Locality
ForCES is intended for environments where one of the following
applies:
o The control interconnect is some form of local bus, switch, or
LAN, where reliability is high, closely controlled, and not
susceptible to external disruption that does not also affect the
CEs and/or FEs.
o The control interconnect shares its fate with the FE's forwarding
function. Typically this is because the control connection is
also the FE's primary packet forwarding connection, and so if that
link goes down, the FE cannot forward packets anyway.
The key guideline is that the reliability of the device should not be
significantly reduced by the separation of control and forwarding
functionality.
Crouch, et al. Informational [Page 8]
RFC 6041 ForCES Applicability Statement October 2010
Taking this into account, ForCES is applicable in the following CE/FE
localities:
Single Box NE:
chassis with multiple CEs and FEs set up. ForCES is applicable in
localities consisting of control and forwarding elements that are
components in the same physical box.
Example: a network element with a single control blade, and one or
more forwarding blades, all present in the same chassis and
sharing an interconnect such as Ethernet or Peripheral Component
Interconnect (PCI). In this locality, the majority of the data
traffic being forwarded typically does not traverse the same links
as the ForCES control traffic.
Multiple Box NE:
separated CE and FE, where physical locality could be the same
rack, room, or building; or long distances that could span across
continents and oceans. ForCES is applicable in localities
consisting of control and forwarding elements that are separated
by a single hop or multiple hops in the network.
5. Security Considerations
The ForCES protocol allows for a variety of security levels
[RFC5810]. When operating under a secured physical environment, or
for other operational concerns (in some cases, performance issues),
the operator may turn off all the security functions between CEs and
FEs. When the operator makes a decision to secure the path between
the FEs and CEs, then the operator chooses from one of the options
provided by the TML. Security choices provided by the TML take
effect during the pre-association phase of the ForCES protocol. An
operator may choose to use all, some, or none of the security
services provided by the TML in a CE-FE connection. A ForCES NE is
required to provide CE/FE node authentication services, and may
provide message integrity and confidentiality services. The NE may
provide these services by employing IPsec or Transport Layer Security
(TLS), depending on the choice of TML used in the deployment of
the NE.
6. ForCES Manageability
From the architectural perspective, the ForCES NE is a single network
element. As an example, if the ForCES NE is specifically a router
that needs to be managed, then it should be managed in essentially
the same way any router should be managed. From another perspective,
element management could directly view the individual entities and
interfaces that make up a ForCES NE. However, any element management
Crouch, et al. Informational [Page 9]
RFC 6041 ForCES Applicability Statement October 2010
updates made directly on these entities and interfaces may compromise
the control relationship between the CEs and the FEs, unless the
update mechanism has been accounted for in the model used by the NE.
6.1. The NE as an Atomic Element
From the ForCES Requirements [RFC3654], Section 4, point 4:
A NE MUST support the appearance of a single functional device.
As a single functional device, a ForCES NE runs protocols, and each
of the protocols has its own existing manageability aspects that are
documented elsewhere. As an example, a router would also have a
configuration interface. When viewed in this manner, the NE is
controlled as a single routing entity, and no new management beyond
what is already available for routers and routing protocols would be
required for a ForCES NE. Management commands on a management
interface to the NE will arrive at the CE and may require ForCES
interactions between the CE and FEs to complete. This may impact the
atomicity of such commands and may require careful implementation by
the CE.
6.2. The NE as Composed of Manageable Elements
When viewed as a decomposed set of elements from the management
perspective, the ForCES NE is divided into a set of one of more
control elements, forwarding elements, and the interfaces between
them. The interface functionality between the CE and the FE is
provided by the ForCES protocol. A MIB module is provided for the
purpose of gaining management information on the operation of the
protocol described in Section 6.3 of this document.
Additionally, the architecture makes provisions for configuration
control of the individual CEs and FEs. This is handled by elements
called the FE Manager (FEM) and the CE Manager (CEM). Specifically,
from the ForCES Requirements RFC [RFC3654], Section 4, point 4:
However, external entities (e.g., FE Managers and CE Managers) MAY
have direct access to individual ForCES protocol elements for
providing information to transition them from the pre-association
to the post-association phase.
6.3. ForCES Protocol MIB
The ForCES MIB [RFC5813] defines a primarily read-only MIB module
that captures information related to the ForCES protocol. This
includes state information about the associations between CE(s) and
FE(s) in the NE.
Crouch, et al. Informational [Page 10]
RFC 6041 ForCES Applicability Statement October 2010
The ForCES MIB does not include information that is specified in
other MIB modules, such as packet counters for interfaces, etc.
More specifically, the information in the ForCES MIB module relative
to associations includes:
o identifiers of the elements in the association
o state of the association
o configuration parameters of the association
o statistics of the association
6.3.1. MIB Management of an FE
While it is possible to manage an FE from an element manager, several
requirements relating to this have been included in the ForCES
Requirements.
From the ForCES Requirements [RFC3654], Section 4, point 14:
1. The ability for a management tool (e.g., SNMP) to be used to
read (but not change) the state of FE SHOULD NOT be precluded.
2. It MUST NOT be possible for management tools (e.g., SNMP, etc)
to change the state of a FE in a manner that affects overall NE
behavior without the CE being notified.
The ForCES Framework [RFC3746], Section 5.7, goes further in
discussing the manner in which FEs should handle management requests
that are specifically directed to the FE:
(For a ForCES NE that is an IP router,) RFC 1812 [RFC1812] also
dictates that "Routers must be manageable by SNMP". In general,
for the post-association phase, most external management tasks
(including SNMP) should be done through interaction with the CE in
order to support the appearance of a single functional device.
Therefore, it is recommended that an SNMP agent be implemented by
CEs and that the SNMP messages received by FEs be redirected to
their CEs. AgentX framework defined in RFC 2741 [RFC2741]) may be
applied here such that CEs act in the role of master agent to
process SNMP messages while FEs act in the role of subagent to
provide access to the MIB objects residing on FEs. AgentX
protocol messages between the master agent (CE) and the subagent
(FE) are encapsulated and transported via ForCES, just like data
packets from any other application layer protocols.
Crouch, et al. Informational [Page 11]
RFC 6041 ForCES Applicability Statement October 2010
6.4. The FEM and CEM
Though out of scope for the initial ForCES specification effort, the
ForCES architecture includes two entities: the CE Manager (CEM) and
the FE Manager (FEM). From the ForCES Protocol Specification
[RFC5810]:
CE Manager (CEM):
A logical entity responsible for generic CE management tasks. It
is particularly used during the pre-association phase to determine
with which FE(s) a CE should communicate.
FE Manager (FEM):
A logical entity responsible for generic FE management tasks. It
is used during the pre-association phase to determine with which
CE(s) an FE should communicate.
7. Contributors
Mark Handley was an initial author involved in the earlier versions
of this document.
8. Acknowledgments
Many of the participants in the ForCES WG, as well as fellow
employees of the authors, have provided valuable input into this
work. Particular thanks go to Jamal Hadi Salim, our WG chair and
document shepherd; and to Adrian Farrel, the AD for the area; for
their review, comments, and encouragement, without which this
document might never have been completed.
9. References
9.1. Normative References
[RFC1812] Baker, F., "Requirements for IP Version 4 Routers",
RFC 1812, June 1995.
[RFC5810] Doria, A., Hadi Salim, J., Haas, R., Khosravi, H., Wang,
W., Dong, L., Gopal, R., and J. Halpern, "Forwarding and
Control Element Separation (ForCES) Protocol
Specification", RFC 5810, March 2010.
[RFC5811] Hadi Salim, J. and K. Ogawa, "SCTP-Based Transport
Mapping Layer (TML) for the Forwarding and Control
Element Separation (ForCES) Protocol", RFC 5811,
March 2010.
Crouch, et al. Informational [Page 12]
RFC 6041 ForCES Applicability Statement October 2010
[RFC5812] Halpern, J. and J. Hadi Salim, "Forwarding and Control
Element Separation (ForCES) Forwarding Element Model",
RFC 5812, March 2010.
[RFC5813] Haas, R., "Forwarding and Control Element Separation
(ForCES) MIB", RFC 5813, March 2010.
9.2. Informative References
[RFC2741] Daniele, M., Wijnen, B., Ellison, M., and D. Francisco,
"Agent Extensibility (AgentX) Protocol Version 1",
RFC 2741, January 2000.
[RFC3654] Khosravi, H. and T. Anderson, "Requirements for
Separation of IP Control and Forwarding", RFC 3654,
November 2003.
[RFC3746] Yang, L., Dantu, R., Anderson, T., and R. Gopal,
"Forwarding and Control Element Separation (ForCES)
Framework", RFC 3746, April 2004.
Crouch, et al. Informational [Page 13]
RFC 6041 ForCES Applicability Statement October 2010
Authors' Addresses
Alan Crouch
Intel
2111 NE 25th Avenue
Hillsboro, OR 97124
USA
Phone: +1 503 264 2196
EMail: alan.crouch@intel.com
Hormuzd Khosravi
Intel
2111 NE 25th Avenue
Hillsboro, OR 97124
USA
Phone: 1-503-264-0334
EMail: hormuzd.m.khosravi@intel.com
Avri Doria (editor)
LTU
Lulea University of Technology
Sweden
Phone: +46 73 277 1788
EMail: avri@acm.org
Xin-ping Wang
Huawei
Beijing
China
Phone: +86 10 82836067
EMail: carly.wang@huawei.com
Kentaro Ogawa
NTT Corporation
3-9-11 Midori-cho
Musashino-shi, Tokyo 180-8585
Japan
EMail: ogawa.kentaro@lab.ntt.co.jp
Crouch, et al. Informational [Page 14]