💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc1162.txt captured on 2022-03-01 at 20:54:10.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group Greg Satz
Request for Comments: 1162 cisco Systems, Inc.
June 1990
Connectionless Network Protocol (ISO 8473)
and
End System to Intermediate System (ISO 9542)
Management Information Base
Table of Contents
1. Status of this Memo .................................. 1
2. Historical Perspective................................ 2
3. Objects .............................................. 3
3.1 Format of Definitions ............................... 3
4. Object Definitions ................................... 4
4.1 The CLNP Group ...................................... 5
4.1.1 The CLNP Interfaces table ......................... 14
4.1.2 The CLNP Routing table ............................ 16
4.1.3 The CLNP Address Translation Tables ............... 22
4.2 The CLNP Error Group ................................ 30
4.3 The ESIS Group ...................................... 47
5. Definitions .......................................... 50
6. Identification of OBJECT instances for use with the
SNMP ................................................. 66
6.1 clnpAddrTable Object Type Names ..................... 67
6.2 clnpRoutingTable Object Type Names .................. 67
6.3 clnpNetToMediaTable Object Type Names ............... 68
6.4 clnpMediaToNetTable Object Type Names ............... 68
7. References ........................................... 69
8. Security Considerations............................... 70
9. Author's Address...................................... 70
1. Status of this Memo
This memo defines an experimental portion of the Management
Information Base (MIB) for use with network management protocols in
TCP/IP-based internets.
This memo does not specify a standard for the Internet community.
However, after experimentation, if sufficient consensus is reached in
the Internet community, then a subsequent revision of this document
may be placed in the Internet-standard MIB.
Distribution of this memo is unlimited.
Satz [Page 1]
RFC 1162 CLNS MIB June 1990
2. Historical Perspective
As reported in RFC 1052, IAB Recommendations for the Development of
Internet Network Management Standards [1], a two-prong strategy for
network management of TCP/IP-based internets was undertaken. In the
short-term, the Simple Network Management Protocol (SNMP), defined in
RFC 1067, was to be used to manage nodes in the Internet community.
In the long-term, the use of the OSI network management framework was
to be examined. Two documents were produced to define the management
information: RFC 1065, which defined the Structure of Management
Information (SMI), and RFC 1066, which defined the Management
Information Base (MIB). Both of these documents were designed so as
to be compatible with both the SNMP and the OSI network management
framework.
This strategy was quite successful in the short-term: Internet-based
network management technology was fielded, by both the research and
commercial communities, within a few months. As a result of this,
portions of the Internet community became network manageable in a
timely fashion.
As reported in RFC 1109, Report of the Second Ad Hoc Network
Management Review Group [2], the requirements of the SNMP and the OSI
network management frameworks were more different than anticipated.
As such, the requirement for compatibility between the SMI/MIB and
both frameworks was suspended. This action permitted the operational
network management framework, based on the SNMP, to respond to new
operational needs in the Internet community by producing MIB-II.
In May of 1990, the core documents were elevated to "Standard
Protocols" with "Recommended" status. As such, the Internet-
standard network management framework consists of: Structure and
Identification of Management Information for TCP/IP-based internets,
RFC 1155 [3], which describes how managed objects contained in the
MIB are defined; Management Information Base for Network Management
of TCP/IP-based internets, which describes the managed objects
contained in the MIB, RFC 1156 [4]; and, the Simple Network
Management Protocol, RFC 1157 [5], which defines the protocol used to
manage these objects.
Consistent with the IAB directive to produce simple, workable systems
in the short-term, the list of managed objects defined in the
Internet-standard MIB was derived by taking only those elements which
are considered essential. However, the SMI defined three
extensibility mechanisms: one, the addition of new standard objects
through the definitions of new versions of the MIB; two, the addition
of widely-available but non-standard objects through the experimental
subtree; and three, the addition of private objects through the
Satz [Page 2]
RFC 1162 CLNS MIB June 1990
enterprises subtree. Such additional objects can not only be used
for vendor-specific elements, but also for experimentation as
required to further the knowledge of which other objects are
essential.
Since the publication of the Internet-standard MIB, experience has
lead to a new document, termed MIB-II [6], being defined.
This memo defines extensions to the MIB using the second method. It
contains definitions of managed objects used for experimentation.
After experimentation, if sufficient consensus is reached in the
Internet community, then a subsequent revision of this memo may be
placed in the Internet-standard MIB.
3. Objects
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the subset of Abstract Syntax Notation One (ASN.1) [7]
defined in the SMI. In particular, each object has a name, a syntax,
and an encoding. The name is an object identifier, an
administratively assigned name, which specifies an object type. The
object type together with an object instance serves to uniquely
identify a specific instantiation of the object. For human
convenience, we often use a textual string, termed the OBJECT
DESCRIPTOR, to also refer to the object type.
The syntax of an object type defines the abstract data structure
corresponding to that object type. The ASN.1 language is used for
this purpose. However, the SMI [3] purposely restricts the ASN.1
constructs which may be used. These restrictions are explicitly made
for simplicity.
The encoding of an object type is simply how that object type is
represented using the object type's syntax. Implicitly tied to the
notion of an object type's syntax and encoding is how the object type
is represented when being transmitted on the network.
This SMI specifies the use of the basic encoding rules of ASN.1 [8],
subject to the additional requirements imposed by the SNMP.
3.1. Format of Definitions
The next section contains the specification of all object types
contained in the MIB. Following the conventions of the companion
memo, the object types are defined using the following fields:
Satz [Page 3]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
A textual name, termed the OBJECT DESCRIPTOR, for the
object type, along with its corresponding OBJECT
IDENTIFIER.
Syntax:
The abstract syntax for the object type, presented using
ASN.1. This must resolve to an instance of the ASN.1
type ObjectSyntax defined in the SMI.
Definition:
A textual description of the semantics of the object
type. Implementations should ensure that their
interpretation of the object type fulfills this
definition since this MIB is intended for use in multi-
vendor environments. As such it is vital that object
types have consistent meaning across all machines.
Access:
A keyword, one of read-only, read-write, write-only, or
not-accessible. Note that this designation specifies the
minimum level of support required. As a local matter,
implementations may support other access types (e.g., an
implementation may elect to permitting writing a variable
marked herein as read-only). Further, protocol-specific
"views" (e.g., those implied by an SNMP community) may
make further restrictions on access to a variable.
Status:
A keyword, one of mandatory, optional, obsolete, or
deprecated. Use of deprecated implies mandatory status.
4. Object Definitions
CLNS-MIB DEFINITIONS ::= BEGIN
IMPORTS
experimental, OBJECT-TYPE, Counter
FROM RFC1155-SMI;
-- new type of NetworkAddress
ClnpAddress ::=
[APPLICATION 5]
IMPLICIT OCTET STRING (SIZE (1..21))
Satz [Page 4]
RFC 1162 CLNS MIB June 1990
clns OBJECT IDENTIFIER ::= { experimental 1 }
clnp OBJECT IDENTIFIER ::= { clns 1 }
error OBJECT IDENTIFIER ::= { clns 2 }
echo OBJECT IDENTIFIER ::= { clns 3 }
es-is OBJECT IDENTIFIER ::= { clns 4 }
END
These objects can be used when the ISO Connectionless-mode Network
Protocol [9] and End System to Intermediate System [10] protocols are
present. No assumptions are made as to what underlying protocol is
being used to carry the SNMP.
This memo uses the string encoding of [11] to textually describe OSI
addresses.
The ASN.1 type ClnpAddress is used to denote an OSI address. This
consists of a string of octets. The first octet of the string
contains a binary value in the range of 0..20, and indicates the the
length in octets of the NSAP. Following the first octet, is the
NSAP, expressed in concrete binary notation, starting with the most
significant octet. A zero- length NSAP is used as a "special"
address meaning "the default NSAP" (analogous to the IP address of
0.0.0.0). Such an NSAP is encoded as a single octet, containing the
value 0.
All other NSAPs are encoded in at least 2 octets.
4.1. The CLNP Group
Implementation is experimental and is recommended for all systems
that support a CLNP.
OBJECT:
-------
clnpForwarding { clnp 1 }
Syntax:
INTEGER {
is(1), -- entity is an intermediate system
es(2), -- entity is an end system and does not
forward PDUs
}
Definition:
The indication of whether this entity is active as an
Satz [Page 5]
RFC 1162 CLNS MIB June 1990
intermediate or end system. Only intermediate systems
will forward PDUs onward that are not addressed to them.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpDefaultLifeTime { clnp 2 }
Syntax:
INTEGER
Definition:
The default value inserted into the Lifetime field of the
CLNP PDU header of PDUs sourced by this entity.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpInReceives { clnp 3 }
Syntax:
Counter
Definition:
The total number of input PDUs received from all
connected network interfaces running CLNP, including
errors.
Access:
read-only.
Status:
mandatory.
Satz [Page 6]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpInHdrErrors { clnp 4 }
Syntax:
Counter
Definition:
The number of input PDUs discarded due to errors in the
CLNP header, including bad checksums, version mismatch,
lifetime exceeded, errors discovered in processing
options, etc.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInAddrErrors { clnp 5 }
Syntax:
Counter
Definition:
The number of input PDUs discarded because the NSAP
address in the CLNP header's destination field was not a
valid NSAP to be received at this entity. This count
includes addresses not understood. For end systems, this
is a count of PDUs which arrived with a destination NSAP
which was not local.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpForwPDUs { clnp 6 }
Syntax:
Counter
Satz [Page 7]
RFC 1162 CLNS MIB June 1990
Definition:
The number of input PDUs for which this entity was not
the final destination and which an attempt was made to
forward them onward.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInUnknownNLPs { clnp 7 }
Syntax:
Counter
Definition:
The number of locally-addressed PDUs successfully
received but discarded because the network layer protocol
was unknown or unsupported (e.g., not CLNP or ES-IS).
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInUnknownULPs { clnp 8 }
Syntax:
Counter
Definition:
The number of locally-addressed PDUs successfully
received but discarded because the upper layer protocol
was unknown or unsupported (e.g., not TP4).
Access:
read-only.
Status:
mandatory.
Satz [Page 8]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpInDiscards { clnp 9 }
Syntax:
Counter
Definition:
The number of input CLNP PDUs for which no problems were
encountered to prevent their continued processing, but
were discarded (e.g., for lack of buffer space). Note that
this counter does not include any PDUs discarded while
awaiting re-assembly.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInDelivers { clnp 10 }
Syntax:
Counter
Definition:
The total number of input PDUs successfully delivered to
the CLNS transport user.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutRequests { clnp 11 }
Syntax:
Counter
Definition:
The total number of CLNP PDUs which local CLNS user
Satz [Page 9]
RFC 1162 CLNS MIB June 1990
protocols supplied to CLNP for transmission requests.
This counter does not include any PDUs counted in
clnpForwPDUs.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutDiscards { clnp 12 }
Syntax:
Counter
Definition:
The number of output CLNP PDUs for which no other problem
was encountered to prevent their transmission but were
discarded (e.g., for lack of buffer space). Note this
counter includes PDUs counted in clnpForwPDUs.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutNoRoutes { clnp 13 }
Syntax:
Counter
Definition:
The number of CLNP PDUs discarded because no route could
be found to transmit them to their destination. This
counter includes any PDUs counted in clnpForwPDUs.
Access:
read-only.
Status:
mandatory.
Satz [Page 10]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpReasmTimeout { clnp 14 }
Syntax:
INTEGER
Definition:
The maximum number of seconds which received segments are
held while they are awaiting reassembly at this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpReasmReqds { clnp 15 }
Syntax:
Counter
Definition:
The number of CLNP segments received which needed to be
reassembled at this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpReasmOKs { clnp 16 }
Syntax:
Counter
Definition:
The number of CLNP PDUs successfully re-assembled at this
entity.
Satz [Page 11]
RFC 1162 CLNS MIB June 1990
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpReasmFails { clnp 17 }
Syntax:
Counter
Definition:
The number of failures detected by the CLNP reassembly
algorithm (for any reason: timed out, buffer size, etc).
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpSegOKs { clnp 18 }
Syntax:
Counter
Definition:
The number of CLNP PDUs that have been successfully
segmented at this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpSegFails { clnp 19 }
Satz [Page 12]
RFC 1162 CLNS MIB June 1990
Syntax:
Counter
Definition:
The number of CLNP PDUs that have been discarded because
they needed to be fragmented at this entity but could
not.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpSegCreates { clnp 20 }
Syntax:
Counter
Definition:
The number of CLNP PDU segments that have been generated
as a result of segmentation at this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInOpts { clnp 25 }
Syntax:
Counter
Definition:
The number of CLNP PDU segments that have been input with
options at this entity.
Access:
read-only.
Satz [Page 13]
RFC 1162 CLNS MIB June 1990
Status:
mandatory.
OBJECT:
-------
clnpOutOpts { clnp 26 }
Syntax:
Counter
Definition:
The number of CLNP PDU segments that have been generated
with options by this entity.
Access:
read-only.
Status:
mandatory.
4.1.1. The CLNP Interfaces table
The CLNP Interfaces table contains information on the entity's
interfaces which are running the CLNP.
OBJECT:
-------
clnpAddrTable { clnp 21 }
Syntax:
SEQUENCE OF ClnpAddrEntry
Definition:
The table of addressing information relevant to this
entity's CLNP addresses.
Access:
not-accessible.
Status:
mandatory.
OBJECT:
-------
clnpAddrEntry { clnpAddrTable 1 }
Satz [Page 14]
RFC 1162 CLNS MIB June 1990
Syntax:
ClnpAddrEntry :: = SEQUENCE {
clnpAdEntAddr
ClnpAddress,
clnpAdEntIfIndex
INTEGER,
clnpAdEntReasmMaxSize
INTEGER (0..65535)
}
Definition:
The addressing information for one of this entity's CLNP
addresses.
Access:
not-accessible.
Status:
mandatory.
OBJECT:
-------
clnpAdEntAddr { clnpAddrEntry 1 }
Syntax:
ClnpAddress
Definition:
The CLNP address to which this entry's addressing
information pertains.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpAdEntIfIndex { clnpAddrEntry 2 }
Syntax:
INTEGER
Definition:
The index value which uniquely identifies the interface
Satz [Page 15]
RFC 1162 CLNS MIB June 1990
to which this entry is applicable. The interface
identified by a particular value of this index is the
same interface as identified by the same value of
ifIndex.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpAdEntReasmMaxSize { clnpAddrEntry 3 }
Syntax:
INTEGER (0..65535)
Definition:
The size of the largest CLNP PDU which this entity can
re-assemble from incoming CLNP segmented PDUs received on
this interface.
Access:
read-only.
Status:
mandatory.
4.1.2. The CLNP Routing table
The CLNP Routing table contains an entry for each route known to the
entity.
OBJECT:
-------
clnpRoutingTable { clnp 22 }
Syntax:
SEQUENCE OF ClnpRouteEntry
Definition:
This entity's CLNP routing table.
Access:
not-accessible.
Satz [Page 16]
RFC 1162 CLNS MIB June 1990
Status:
mandatory.
OBJECT:
-------
clnpRouteEntry { clnpRoutingTable 1 }
Syntax:
ClnpRouteEntry ::= SEQUENCE {
clnpRouteDest
ClnpAddress,
clnpRouteIfIndex
INTEGER,
clnpRouteMetric1
INTEGER,
clnpRouteMetric2
INTEGER,
clnpRouteMetric3
INTEGER,
clnpRouteMetric4
INTEGER,
clnpRouteNextHop
ClnpAddress,
clnpRouteType
INTEGER,
clnpRouteProto
INTEGER,
clnpRouteAge
INTEGER
}
Definition:
A route to a particular destination.
Access:
not-accessible.
Status:
mandatory.
OBJECT:
-------
clnpRouteDest { clnpRouteEntry 1 }
Syntax:
ClnpAddress
Satz [Page 17]
RFC 1162 CLNS MIB June 1990
Definition:
The destination CLNP address of this route.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpRouteIfIndex { clnpRouteEntry 2 }
Syntax:
INTEGER
Definition:
The index value which uniquely identifies the local
interface through which the next hop of this route should
be reached. The interface identified by a particular
value of this index is the same as identified by the same
value of ifIndex.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpRouteMetric1 { clnpRouteEntry 3 }
Syntax:
INTEGER
Definition:
The primary routing metric for this route. The semantics
of this metric are determined by the routing-protocol
specified in the route's clnpRouteProto value. If this
metric is not used, its value should be set to -1.
Access:
read-write.
Satz [Page 18]
RFC 1162 CLNS MIB June 1990
Status:
mandatory.
OBJECT:
-------
clnpRouteMetric2 { clnpRouteEntry 4 }
Syntax:
INTEGER
Definition:
An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's clnpRouteProto value.
If this metric is not used, its value should be set to
-1.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpRouteMetric3 { clnpRouteEntry 5 }
Syntax:
INTEGER
Definition:
An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's clnpRouteProto value.
If this metric is not used, its value should be set to
-1.
Access:
read-write.
Status:
mandatory.
Satz [Page 19]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpRouteMetric4 { clnpRouteEntry 6 }
Syntax:
INTEGER
Definition:
An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's clnpRouteProto value.
If this metric is not used, its value should be set to
-1.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpRouteNextHop { clnpRouteEntry 7 }
Syntax:
ClnpAddress
Definition:
The CLNP address of the next hop of this route.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpRouteType { clnpRouteEntry 8 }
Syntax:
INTEGER {
other(1), -- none of the following
invalid(2), -- an invalidated route
Satz [Page 20]
RFC 1162 CLNS MIB June 1990
-- route to directly
direct(3), -- connected (sub-)network
-- route to a non-local
remote(4) -- host/network/sub-network
}
Definition:
The type of route.
Setting this object to the value invalid(2) has the effect of
invaliding the corresponding entry in the clnpRoutingTable.
That is, it effectively dissasociates the destination
identified with said entry from the route identified with said
entry. It is an implementation-specific matter as to whether
the agent removes an invalidated entry from the table.
Accordingly, management stations must be prepared to receive
tabular information from agents that corresponds to entries
not currently in use. Proper interpretation of such entries
requires examination of the relevant clnpRouteType object.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpRouteProto { clnpRouteEntry 9 }
Syntax:
INTEGER {
other(1), -- none of the following
-- non-protocol information
-- e.g., manually
local(2), -- configured entries
-- set via a network
netmgmt(3), -- management protocol
-- similar to ipRouteProto
-- but omits several IP-specific
-- protocols
is-is(9),
Satz [Page 21]
RFC 1162 CLNS MIB June 1990
ciscoIgrp(11),
bbnSpfIgp(12),
ospf(13),
bgp(14)
}
Definition:
The routing mechanism via which this route was learned.
Inclusion of values for gateway routing protocols is not
intended to imply that hosts should support those
protocols.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpRouteAge { clnpRouteEntry 10 }
Syntax:
INTEGER
Definition:
The number of seconds since this route was last updated
or otherwise determined to be correct. Note that no
semantics of "too old" can be implied except through
knowledge of the routing protocol by which the route was
learned.
Access:
read-write.
Status:
mandatory.
4.1.3. The CLNP Address Translation Tables
The Address Translation tables contain the CLNP address to physical
address equivalences. Some interfaces do not use translation tables
for determining address equivalences; if all interfaces are of this
type, then the Address Translation table is empty, i.e., has zero
entries.
Satz [Page 22]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpNetToMediaTable { clnp 23 }
Syntax:
SEQUENCE OF ClnpNetToMediaEntry
Definition:
The CLNP Address Translation table used for mapping from
CLNP addresses to physical addresses.
Access:
not-accessible
Status:
mandatory.
OBJECT:
-------
clnpNetToMediaEntry { clnpNetToMediaTable 1 }
Syntax:
ClnpNetToMediaEntry ::= SEQUENCE {
clnpNetToMediaIfIndex
INTEGER,
clnpNetToMediaPhysAddress
OCTET STRING,
clnpNetToMediaNetAddress
ClnpAddress,
clnpNetToMediaType
INTEGER,
clnpNetToMediaAge
INTEGER,
clnpNetToMediaHoldTime
INTEGER
}
Definition:
Each entry contains one CLNP address to "physical"
address equivalence.
Access:
not-accessible.
Status:
mandatory.
Satz [Page 23]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpNetToMediaIfIndex { clnpNetToMediaEntry 1 }
Syntax:
INTEGER
Definition:
The interface on which this entry's equivalence is
effective. The interface identified by a particular
value of this index is the same interface as identified
by the same value of ifIndex.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpNetToMediaPhysAddress { clnpNetToMediaEntry 2 }
Syntax:
OCTET STRING
Definition:
The media-dependent "physical" address.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpNetToMediaNetAddress { clnpNetToMediaEntry 3 }
Syntax:
ClnpAddress
Definition:
The CLNP address corresponding to the media-dependent
"physical" address.
Satz [Page 24]
RFC 1162 CLNS MIB June 1990
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpNetToMediaType { clnpNetToMediaEntry 4 }
Syntax:
INTEGER {
other(1), -- none of the following
invalid(2), -- an invalidated mapping
dynamic(3),
static(4)
}
Definition:
The type of mapping.
Setting this object to the value invalid(2) has the effect of
invalidating the corresponding entry in the
clnpNetToMediaTable. That is, it effectively dissassociates
the interface identified with said entry from the mapping
identified with said entry. It is an implementation-specific
matter as to whether the agent removes an invalidated entry
from the table. Accordingly, management stations must be
prepared to receive tabular information from agents that
corresponds to entries not currently in use. Proper
interpretation of such entries requires examination of the
relevant clnpNetToMediaType object.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpNetToMediaAge { clnpNetToMediaEntry 5 }
Syntax:
INTEGER
Satz [Page 25]
RFC 1162 CLNS MIB June 1990
Definition:
The number of seconds since this entry was last updated
or otherwise determined to be correct. Note that no
semantics of "too old" can be implied except through
knowledge of the type of entry.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpNetToMediaHoldTime { clnpNetToMediaEntry 6 }
Syntax:
INTEGER
Definition:
The time in seconds this entry will be valid. Static
entries should always report this field as -1.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpMediaToNetTable { clnp 24 }
Syntax:
SEQUENCE OF ClnpMediaToNetEntry
Definition:
The CLNP Address Translation table used for mapping from
physical addresses to CLNP addresses.
Access:
not-accessible.
Status:
mandatory.
Satz [Page 26]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpMediaToNetEntry { clnpMediaToNetTable 1 }
Syntax:
ClnpMediaToNetEntry ::= SEQUENCE {
clnpMediaToNetIfIndex
INTEGER,
clnpMediaToNetNetAddress
ClnpAddress,
clnpMediaToNetPhysAddress
OCTET STRING,
clnpMediaToNetType
INTEGER,
clnpMediaToNetAge
INTEGER,
clnpMediaToNetHoldTime
INTEGER
}
Definition:
Each entry contains on ClnpAddress to "physical" address
equivalence.
Access:
not-accessible.
Status:
mandatory.
OBJECT:
-------
clnpMediaToNetIfIndex { clnpMediaToNetEntry 1 }
Syntax:
INTEGER
Definition:
The interface on which this entry's equivalence is
effective. The interface identified by a particular
value of this index is the same interface as identified
by the same value of ifIndex.
Access:
read-write.
Satz [Page 27]
RFC 1162 CLNS MIB June 1990
Status:
mandatory.
OBJECT:
-------
clnpMediaToNetAddress { clnpMediaToNetEntry 2 }
Syntax:
ClnpAddress
Definition:
The ClnpAddress corresponding to the media-dependent
"physical" address.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpMediaToNetPhysAddress { clnpMediaToNetEntry 3 }
Syntax:
OCTET STRING
Definition:
The media-dependent "physical" address.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpMediaToNetType { clnpMediaToNetEntry 4 }
Syntax:
INTEGER {
other(1), -- none of the following
invalid(2), -- an invalidated mapping
dynamic(3),
Satz [Page 28]
RFC 1162 CLNS MIB June 1990
static(4)
}
Definition:
The type of mapping.
Setting this object to the value invalid(2) has the effect of
invalidating the corresponding entry in the
clnpMediaToNetTable. That is, it effectively dissassociates
the interface identified with said entry from the mapping
identified with said entry. It is an implementation-specific
matter as to whether the agent removes an invalidated entry
from the table. Accordingly, management stations must be
prepared to receive tabular information from agents that
corresponds to entries not currently in use. Proper
interpretation of such entries requires examination of the
relevant clnpMediaToNetType object.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpMediaToNetAge { clnpMediaToNetEntry 5 }
Syntax:
INTEGER
Definition:
The number of seconds since this entry was last updated
or otherwise determined to be correct. Note that no
semantics of "too old" can be implied except through
knowledge of the type of entry.
Access:
read-write.
Status:
mandatory.
OBJECT:
-------
clnpMediaToNetHoldTime { clnpMediaToNetEntry 6 }
Satz [Page 29]
RFC 1162 CLNS MIB June 1990
Syntax:
INTEGER
Definition:
The time in seconds this entry will be valid. Static
entries should always report this field as -1.
Access:
read-write.
Status:
mandatory.
4.2. The CLNP Error Group
This group records the CLNP Error protocol and is recommended for all
systems which support CLNP.
OBJECT:
-------
clnpInErrors { error 1 }
Syntax:
Counter
Definition:
The number of CLNP Error PDUs received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrors { error 2 }
Syntax:
Counter
Definition:
The number of CLNP Error PDUs sent by this entity.
Access:
read-only.
Satz [Page 30]
RFC 1162 CLNS MIB June 1990
Status:
mandatory.
OBJECT:
-------
clnpInErrUnspecs { error 3 }
Syntax:
Counter
Definition:
The number of unspecified CLNP Error PDUs received by
this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrProcs { error 4 }
Syntax:
Counter
Definition:
The number of protocol procedure CLNP Error PDUs received
by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrCksums { error 5 }
Syntax:
Counter
Satz [Page 31]
RFC 1162 CLNS MIB June 1990
Definition:
The number of checksum CLNP Error PDUs received by this
entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrCongests { error 6 }
Syntax:
Counter
Definition:
The number of congestion drop CLNP Error PDUs received by
this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrHdrs { error 7 }
Syntax:
Counter
Definition:
The number of header syntax CLNP Error PDUs received by
this entity.
Access:
read-only.
Status:
mandatory.
Satz [Page 32]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpInErrSegs { error 8 }
Syntax:
Counter
Definition:
The number of segmentation disallowed CLNP Error PDUs
received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrIncomps { error 9 }
Syntax:
Counter
Definition:
The number of incomplete PDU CLNP Error PDUs received by
this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrDups { error 10 }
Syntax:
Counter
Definition:
The number of duplicate option CLNP Error PDUs received
by this entity.
Satz [Page 33]
RFC 1162 CLNS MIB June 1990
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrUnreachDsts { error 11 }
Syntax:
Counter
Definition:
The number of unreachable destination CLNP Error PDUs
received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrUnknownDsts { error 12 }
Syntax:
Counter
Definition:
The number of unknown destination CLNP Error PDUs
received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrSRUnspecs { error 13 }
Satz [Page 34]
RFC 1162 CLNS MIB June 1990
Syntax:
Counter
Definition:
The number of unspecified source route CLNP Error PDUs
received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrSRSyntaxes { error 14 }
Syntax:
Counter
Definition:
The number of source route syntax CLNP Error PDUs
received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrSRUnkAddrs { error 15 }
Syntax:
Counter
Definition:
The number of source route unknown address CLNP Error
PDUs received by this entity.
Access:
read-only.
Status:
mandatory.
Satz [Page 35]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpInErrSRBadPaths { error 16 }
Syntax:
Counter
Definition:
The number of source route bad path CLNP Error PDUs
received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrHops { error 17 }
Syntax:
Counter
Definition:
The number of hop count exceeded CLNP Error PDUs received
by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrHopReassms { error 18 }
Syntax:
Counter
Definition:
The number of hop count exceeded while reassembling CLNP
Error PDUs received by this entity.
Satz [Page 36]
RFC 1162 CLNS MIB June 1990
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrUnsOptions { error 19 }
Syntax:
Counter
Definition:
The number of unsupported option CLNP Error PDUs received
by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrUnsVersions { error 20 }
Syntax:
Counter
Definition:
The number of version mismatch CLNP Error PDUs received
by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrUnsSecurities { error 21 }
Satz [Page 37]
RFC 1162 CLNS MIB June 1990
Syntax:
Counter
Definition:
The number of unsupported security option CLNP Error PDUs
received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrUnsSRs { error 22 }
Syntax:
Counter
Definition:
The number of unsupported source route option CLNP Error
PDUs received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpInErrUnsRRs { error 23 }
Syntax:
Counter
Definition:
The number of unsupported record route option CLNP Error
PDUs received by this entity.
Access:
read-only.
Status:
mandatory.
Satz [Page 38]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpInErrInterferences { error 24 }
Syntax:
Counter
Definition:
The number of reassembly interference CLNP Error PDUs
received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrUnspecs { error 25 }
Syntax:
Counter
Definition:
The number of unspecified CLNP Error PDUs sent by this
entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrProcs { error 26 }
Syntax:
Counter
Definition:
The number of protocol procedure CLNP Error PDUs sent by
this entity.
Satz [Page 39]
RFC 1162 CLNS MIB June 1990
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrCksums { error 27 }
Syntax:
Counter
Definition:
The number of checksum CLNP Error PDUs sent by this
entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrCongests { error 28 }
Syntax:
Counter
Definition:
The number of congestion drop CLNP Error PDUs sent by
this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrHdrs { error 29 }
Satz [Page 40]
RFC 1162 CLNS MIB June 1990
Syntax:
Counter
Definition:
The number of header syntax CLNP Error PDUs sent by this
entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrSegs { error 30 }
Syntax:
Counter
Definition:
The number of segmentation disallowed CLNP Error PDUs
sent by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrIncomps { error 31 }
Syntax:
Counter
Definition:
The number of incomplete PDU CLNP Error PDUs sent by this
entity.
Access:
read-only.
Status:
mandatory.
Satz [Page 41]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpOutErrDups { error 32 }
Syntax:
Counter
Definition:
The number of duplicate option CLNP Error PDUs sent by
this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrUnreachDsts { error 33 }
Syntax:
Counter
Definition:
The number of unreachable destination CLNP Error PDUs
sent by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrUnknownDsts { error 34 }
Syntax:
Counter
Definition:
The number of unknown destination CLNP Error PDUs sent by
this entity.
Satz [Page 42]
RFC 1162 CLNS MIB June 1990
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrSRUnspecs { error 35 }
Syntax:
Counter
Definition:
The number of unspecified source route CLNP Error PDUs
sent by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrSRSyntaxes { error 36 }
Syntax:
Counter
Definition:
The number of source route syntax CLNP Error PDUs sent by
this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrSRUnkAddrs { error 37 }
Satz [Page 43]
RFC 1162 CLNS MIB June 1990
Syntax:
Counter
Definition:
The number of source route unknown address CLNP Error
PDUs sent by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrSRBadPaths { error 38 }
Syntax:
Counter
Definition:
The number of source route bad path CLNP Error PDUs sent
by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrHopss { error 39 }
Syntax:
Counter
Definition:
The number of hop count exceeded CLNP Error PDUs sent by
this entity.
Access:
read-only.
Status:
mandatory.
Satz [Page 44]
RFC 1162 CLNS MIB June 1990
OBJECT:
-------
clnpOutErrHopReassms { error 40 }
Syntax:
Counter
Definition:
The number of hop count exceeded while reassembling CLNP
Error PDUs sent by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrUnsOptions { error 41 }
Syntax:
Counter
Definition:
The number of unsupported option CLNP Error PDUs sent by
this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrUnsVersions { error 42 }
Syntax:
Counter
Definition:
The number of version mismatch CLNP Error PDUs sent by
this entity.
Satz [Page 45]
RFC 1162 CLNS MIB June 1990
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrUnsSecurities { error 43 }
Syntax:
Counter
Definition:
The number of unsupported security option CLNP Error PDUs
sent by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrUnsSRs { error 44 }
Syntax:
Counter
Definition:
The number of unsupported source route option CLNP Error
PDUs sent by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrUnsRRs { error 45 }
Satz [Page 46]
RFC 1162 CLNS MIB June 1990
Syntax:
Counter
Definition:
The number of unsupported record route option CLNP Error
PDUs sent by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
clnpOutErrInterferences { error 46 }
Syntax:
Counter
Definition:
The number of reassembly interference CLNP Error PDUs
sent by this entity.
Access:
read-only.
Status:
mandatory.
4.3. The ESIS Group
The ESIS group contains information about the End System Intermediate
System protocol used to maintain neighbor reachibility information.
Both ESs and ISs are expected to implement this group if they running
a CLNP.
OBJECT:
-------
esisESHin { es-is 1 }
Syntax:
Counter
Definition:
The number of ESH PDUs received by this entity.
Satz [Page 47]
RFC 1162 CLNS MIB June 1990
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
esisESHout { es-is 2 }
Syntax:
Counter
Definition:
The number of ESH PDUs sent by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
esisISHin { es-is 3 }
Syntax:
Counter
Definition:
The number of ISH PDUs received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
esisISHout { es-is 4 }
Syntax:
Counter
Satz [Page 48]
RFC 1162 CLNS MIB June 1990
Definition:
The number of ISH PDUs sent by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
esisRDUin { es-is 5 }
Syntax:
Counter
Definition:
The number of RDU PDUs received by this entity.
Access:
read-only.
Status:
mandatory.
OBJECT:
-------
esisRDUout { es-is 6 }
Syntax:
Counter
Definition:
The number of RDU PDUs sent by this entity.
Access:
read-only.
Status:
mandatory.
Satz [Page 49]
RFC 1162 CLNS MIB June 1990
5. Definitions
CLNS-MIB DEFINITIONS ::= BEGIN
IMPORTS
experimental, OBJECT-TYPE, Counter
FROM RFC1155-SMI;
-- new type of NetworkAddress
ClnpAddress ::=
[APPLICATION 5]
IMPLICIT OCTET STRING (SIZE (1..21))
clns OBJECT IDENTIFIER ::= { experimental 1 }
clnp OBJECT IDENTIFIER ::= { clns 1 }
error OBJECT IDENTIFIER ::= { clns 2 }
echo OBJECT IDENTIFIER ::= { clns 3 }
es-is OBJECT IDENTIFIER ::= { clns 4 }
-- the General CLNP group
clnpForwarding OBJECT-TYPE
SYNTAX INTEGER {
is(1), -- entity is an
-- intermediate system
es(2) -- entity is an end system
-- and does not forward pdus
}
ACCESS read-write
STATUS mandatory
::= { clnp 1 }
clnpDefaultLifeTime OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnp 2 }
clnpInReceives OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 3 }
Satz [Page 50]
RFC 1162 CLNS MIB June 1990
clnpInHdrErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 4 }
clnpInAddrErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 5 }
clnpForwPDUs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 6 }
clnpInUnknownNLPs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 7 }
clnpInUnknownULPs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 8 }
clnpInDiscards OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 9 }
clnpInDelivers OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 10 }
clnpOutRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 11 }
Satz [Page 51]
RFC 1162 CLNS MIB June 1990
clnpOutDiscards OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 12 }
clnpOutNoRoutes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 13 }
clnpReasmTimeout OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
::= { clnp 14 }
clnpReasmReqds OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 15 }
clnpReasmOKs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 16 }
clnpReasmFails OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 17 }
clnpSegOKs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 18 }
clnpSegFails OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 19 }
Satz [Page 52]
RFC 1162 CLNS MIB June 1990
clnpSegCreates OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 20 }
clnpInOpts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 25 }
clnpOutOpts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { clnp 26 }
-- the CLNP Interface table
clnpAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClnpAddrEntry
ACCESS not-accessible
STATUS mandatory
::= { clnp 21 }
clnpAddrEntry OBJECT-TYPE
SYNTAX ClnpAddrEntry
ACCESS not-accessible
STATUS mandatory
-- INDEX { clnpAdEntAddr }
::= { clnpAddrTable 1 }
ClnpAddrEntry ::= SEQUENCE {
clnpAdEntAddr
ClnpAddress,
clnpAdEntIfIndex
INTEGER,
clnpAdEntReasmMaxSize
INTEGER (0..65535)
}
clnpAdEntAddr OBJECT-TYPE
SYNTAX ClnpAddress
ACCESS read-only
STATUS mandatory
::= { clnpAddrEntry 1 }
Satz [Page 53]
RFC 1162 CLNS MIB June 1990
clnpAdEntIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
::= { clnpAddrEntry 2 }
clnpAdEntReasmMaxSize OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
::= { clnpAddrEntry 3 }
-- the CLNP Routing table
clnpRoutingTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClnpRouteEntry
ACCESS not-accessible
STATUS mandatory
::= { clnp 22 }
clnpRouteEntry OBJECT-TYPE
SYNTAX ClnpRouteEntry
ACCESS not-accessible
STATUS mandatory
-- INDEX { clnpRouteDest }
::= { clnpRoutingTable 1 }
ClnpRouteEntry ::= SEQUENCE {
clnpRouteDest
ClnpAddress,
clnpRouteIfIndex
INTEGER,
clnpRouteMetric1
INTEGER,
clnpRouteMetric2
INTEGER,
clnpRouteMetric3
INTEGER,
clnpRouteMetric4
INTEGER,
clnpRouteNextHop
ClnpAddress,
clnpRouteType
INTEGER,
clnpRouteProto
INTEGER,
clnpRouteAge
INTEGER
Satz [Page 54]
RFC 1162 CLNS MIB June 1990
}
clnpRouteDest OBJECT-TYPE
SYNTAX ClnpAddress
ACCESS read-write
STATUS mandatory
::= { clnpRouteEntry 1 }
clnpRouteIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpRouteEntry 2 }
clnpRouteMetric1 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpRouteEntry 3 }
clnpRouteMetric2 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpRouteEntry 4 }
clnpRouteMetric3 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpRouteEntry 5 }
clnpRouteMetric4 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpRouteEntry 6 }
clnpRouteNextHop OBJECT-TYPE
SYNTAX ClnpAddress
ACCESS read-write
STATUS mandatory
::= { clnpRouteEntry 7 }
clnpRouteType OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- none of the
-- following
Satz [Page 55]
RFC 1162 CLNS MIB June 1990
invalid(2), -- an invalidated
-- route
-- route to directly
direct(3), -- connected
-- (sub-)network
-- route to a
-- non-local
remote(4) -- host/network
-- /sub-network
}
ACCESS read-write
STATUS mandatory
::= { clnpRouteEntry 8 }
clnpRouteProto OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- none of the
-- following
-- non-protocol
-- information
-- e.g., manually
local(2), -- configured entries
-- set via a network
netmgmt(3), -- management
-- protocol
-- similar to
-- ipRouteProto
-- but omits several
-- IP-specific
-- protocols
is-is(9),
ciscoIgrp(11),
bbnSpfIgp(12),
ospf(13),
bgp(14)
}
ACCESS read-only
STATUS mandatory
::= { clnpRouteEntry 9 }
clnpRouteAge OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
Satz [Page 56]
RFC 1162 CLNS MIB June 1990
STATUS mandatory
::= { clnpRouteEntry 10 }
-- the CLNP Address Translation tables
clnpNetToMediaTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClnpNetToMediaEntry
ACCESS not-accessible
STATUS mandatory
::= { clnp 23 }
clnpNetToMediaEntry OBJECT-TYPE
SYNTAX ClnpNetToMediaEntry
ACCESS not-accessible
STATUS mandatory
-- INDEX { clnpNetToMediaIfIndex,
-- clnpNetToMediaNetAddress }
::= { clnpNetToMediaTable 1 }
ClnpNetToMediaEntry ::= SEQUENCE {
clnpNetToMediaIfIndex
INTEGER,
clnpNetToMediaPhysAddress
OCTET STRING,
clnpNetToMediaNetAddress
ClnpAddress,
clnpNetToMediaType
INTEGER,
clnpNetToMediaAge
INTEGER,
clnpNetToMediaHoldTime
INTEGER
}
clnpNetToMediaIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpNetToMediaEntry 1 }
clnpNetToMediaPhysAddress OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
::= { clnpNetToMediaEntry 2 }
clnpNetToMediaNetAddress OBJECT-TYPE
SYNTAX ClnpAddress
Satz [Page 57]
RFC 1162 CLNS MIB June 1990
ACCESS read-write
STATUS mandatory
::= { clnpNetToMediaEntry 3 }
clnpNetToMediaType OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- none of the
-- following
invalid(2), -- an invalidated
-- mapping
dynamic(3),
static(4)
}
ACCESS read-write
STATUS mandatory
::= { clnpNetToMediaEntry 4 }
clnpNetToMediaAge OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpNetToMediaEntry 5 }
clnpNetToMediaHoldTime OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpNetToMediaEntry 6 }
clnpMediaToNetTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClnpMediaToNetEntry
ACCESS not-accessible
STATUS mandatory
::= { clnp 24 }
clnpMediaToNetEntry OBJECT-TYPE
SYNTAX ClnpMediaToNetEntry
ACCESS not-accessible
STATUS mandatory
-- INDEX { clnpMediaToNetIfIndex,
-- clnpMediaToNetPhysAddress }
::= { clnpMediaToNetTable 1 }
ClnpMediaToNetEntry ::= SEQUENCE {
clnpMediaToNetIfIndex
INTEGER,
clnpMediaToNetNetAddress
ClnpAddress,
Satz [Page 58]
RFC 1162 CLNS MIB June 1990
clnpMediaToNetPhysAddress
OCTET STRING,
clnpMediaToNetType
INTEGER,
clnpMediaToNetAge
INTEGER,
clnpMediaToNetHoldTime
INTEGER
}
clnpMediaToNetIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpMediaToNetEntry 1 }
clnpMediaToNetNetAddress OBJECT-TYPE
SYNTAX ClnpAddress
ACCESS read-write
STATUS mandatory
::= { clnpMediaToNetEntry 2 }
clnpMediaToNetPhysAddress OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
::= { clnpMediaToNetEntry 3 }
clnpMediaToNetType OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- none of the
-- following
invalid(2), -- an invalidated
-- mapping
dynamic(3),
static(4)
}
ACCESS read-write
STATUS mandatory
::= { clnpMediaToNetEntry 4 }
clnpMediaToNetAge OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpMediaToNetEntry 5 }
clnpMediaToNetHoldTime OBJECT-TYPE
Satz [Page 59]
RFC 1162 CLNS MIB June 1990
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
::= { clnpMediaToNetEntry 6 }
-- the CLNP Error Group
clnpInErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 1 }
clnpOutErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 2 }
clnpInErrUnspecs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 3 }
clnpInErrProcs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 4 }
clnpInErrCksums OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 5 }
clnpInErrCongests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 6 }
clnpInErrHdrs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 7 }
Satz [Page 60]
RFC 1162 CLNS MIB June 1990
clnpInErrSegs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 8 }
clnpInErrIncomps OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 9 }
clnpInErrDups OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 10 }
clnpInErrUnreachDsts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 11 }
clnpInErrUnknownDsts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 12 }
clnpInErrSRUnspecs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 13 }
clnpInErrSRSyntaxes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 14 }
clnpInErrSRUnkAddrs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 15 }
Satz [Page 61]
RFC 1162 CLNS MIB June 1990
clnpInErrSRBadPaths OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 16 }
clnpInErrHops OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 17 }
clnpInErrHopReassms OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 18 }
clnpInErrUnsOptions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 19 }
clnpInErrUnsVersions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 20 }
clnpInErrUnsSecurities OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 21 }
clnpInErrUnsSRs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 22 }
clnpInErrUnsRRs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 23 }
Satz [Page 62]
RFC 1162 CLNS MIB June 1990
clnpInErrInterferences OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 24 }
clnpOutErrUnspecs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 25 }
clnpOutErrProcs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 26 }
clnpOutErrCksums OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 27 }
clnpOutErrCongests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 28 }
clnpOutErrHdrs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 29 }
clnpOutErrSegs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 30 }
clnpOutErrIncomps OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 31 }
Satz [Page 63]
RFC 1162 CLNS MIB June 1990
clnpOutErrDups OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 32 }
clnpOutErrUnreachDsts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 33 }
clnpOutErrUnknownDsts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 34 }
clnpOutErrSRUnspecs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 35 }
clnpOutErrSRSyntaxes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 36 }
clnpOutErrSRUnkAddrs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 37 }
clnpOutErrSRBadPaths OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 38 }
clnpOutErrHops OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 39 }
Satz [Page 64]
RFC 1162 CLNS MIB June 1990
clnpOutErrHopReassms OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 40 }
clnpOutErrUnsOptions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 41 }
clnpOutErrUnsVersions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 42 }
clnpOutErrUnsSecurities OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 43 }
clnpOutErrUnsSRs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 44 }
clnpOutErrUnsRRs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 45 }
clnpOutErrInterferences OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { error 46 }
-- the CLNP Echo Group
-- the ES-IS Group
esisESHins OBJECT-TYPE
Satz [Page 65]
RFC 1162 CLNS MIB June 1990
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { es-is 1 }
esisESHouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { es-is 2 }
esisISHins OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { es-is 3 }
esisISHouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { es-is 4 }
esisRDUins OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { es-is 5 }
esisRDUouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
::= { es-is 6 }
END
6. Identification of OBJECT instances for use with the SNMP
The names for all object types in the MIB are defined explicitly
either in the Internet-standard MIB or in other documents which
conform to the naming conventions of the SMI. The SMI requires that
conformant management protocols define mechanisms for identifying
individual instances of those object types for a particular network
element.
Each instance of any object type defined in the MIB is identified in
SNMP operations by a unique name called its "variable name." In
Satz [Page 66]
RFC 1162 CLNS MIB June 1990
general, the name of an SNMP variable is an OBJECT IDENTIFIER of the
form x.y, where x is the name of a non-aggregate object type defined
in the MIB and y is an OBJECT IDENTIFIER fragment that, in a way
specific to the named object type, identifies the desired instance.
This naming strategy admits the fullest exploitation of the semantics
of the powerful SNMP get-next operator, because it assigns names for
related variables so as to be contiguous in the lexicographical
ordering of all variable names known in the MIB.
The type-specific naming of object instances is defined below for a
number of classes of object types. Instances of an object type to
which none of the following naming conventions are applicable are
named by OBJECT IDENTIFIERs of the form x.0, where x is the name of
said object type in the MIB definition.
For example, suppose one wanted to identify an instance of the
variable sysDescr in the Internet-standard MIB. The object class for
sysDescr is:
iso org dod internet mgmt mib system sysDescr
1 3 6 1 2 1 1 1
Hence, the object type, x, would be 1.3.6.1.2.1.1.1 to which is
appended an instance sub-identifier of 0. That is, 1.3.6.1.2.1.1.1.0
identifies the one and only instance of sysDescr.
6.1. clnpAddrTable Object Type Names
The name of an CLNP-addressable network element, x, is the OBJECT
IDENTIFIER of the form z such that z is the value (in which each
octet of the ClnpAddress type is expressed as a sub-identifier of the
OBJECT IDENTIFIER) of that instance of the clnpAdEntAddr object type
associated with x.
For each object type, t, for which the defined name, n, has a prefix
of clnpAddrEntry, an instance, i, of t is named by an OBJECT
IDENTIFIER of the form n.y, where y is the name of the CLNP-
addressable network element about which i represents information.
For example, suppose one wanted to find the maximum reassembly size
of an entry in the CLNP interface table associated with an CLNP
address of NS+0504030201. Accordingly, clnpAdEntNetMask.5.5.4.3.2.1
would identify the desired instance.
6.2. clnpRoutingTable Object Type Names
The name of an CLNP route, x, is the OBJECT IDENTIFIER of the form z
Satz [Page 67]
RFC 1162 CLNS MIB June 1990
such that z is the value (in which each octet of the ClnpAddress type
is expressed as a sub-identifier of the OBJECT IDENTIFIER) of that
instance of the clnpRouteDest object type associated with x.
For each object type, t, for which the defined name, n, has a prefix
of clnpRoutingEntry, an instance, i, of t is named by an OBJECT
IDENTIFIER of the form n.y, where y is the name of the CLNP route
about which i represents information.
For example, suppose one wanted to find the next hop of an entry in
the CLNP routing table associated with the destination of
NS+0504030201. Accordingly, clnpRouteNextHop.5.5.4.3.2.1 would
identify the desired instance.
At the option of the agent, multiple routes to the same destination
may be visible. To realize this, the agent, while required to return
a single entry for an CLNP route, x, of the form n.y, may also return
information about other routes to the same destination using the form
n.y.v, where v is a implementation-dependent small, non-negative
integer.
6.3. clnpNetToMediaTable Object Type Names
The name of a cached CLNP address, x, is an OBJECT IDENTIFIER of the
form s.z, such that s is the value of that instance of the
clnpNetToMediaIfIndex object type associated with the entry and z is
the value of the CLNP address of the clnpNetToMediaNetAddress object
type associated with x, in which each octet of the ClnpAddress type
is expressed as a sub-identifier of the OBJECT IDENTIFIER.
For each object type, t, for which the defined name, n, has a prefix
of clnpNetToMediaEntry, an instance, i, of t is named by an OBJECT
IDENTIFIER of the form n.y, where y is the name of the cached CLNP
address about which i represents information.
For example, suppose one wanted to find the media address of an entry
in the address translation table associated with a CLNP address of
NS+0504030201 and interface 3. Accordingly,
clnpNetToMediaPhysAddress.3.5.5.4.3.2.1 would identify the desired
instance.
6.4. clnpMediaToNetTable Object Type Names
The name of a cached media address, x, is an OBJECT IDENTIFIER of the
form s.z, such that s is the value of that instance of the
clnpMediaToNetIfIndex object type associated with the entry and z is
the value of the media address of the clnpMediaToNetMediaAddress
object type associated with x, in which each octet of the media
Satz [Page 68]
RFC 1162 CLNS MIB June 1990
address is expressed as a sub- identifier of the OBJECT IDENTIFIER.
For each object type, t, for which the defined name, n, has a prefix
of clnpMediaToNetEntry, an instance, i, of t is named by an OBJECT
IDENTIFIER of the form n.y, where y is the name of the cached media
address about which i represents information.
For example, suppose one wanted to find the CLNP address of an entry
in the address translation table associated with a media address of
08:00:20:00:38:ba and interface 3. Accordingly,
clnpMediaToNetNetAddress.3.8.0.32.0.56.186 would identify the desired
instance.
7. References
[1] Cerf, V., "IAB Recommendations for the Development of Internet
Network Management Standards", RFC 1052, IAB, April 1988.
[2] Cerf, V., "Report of the Second Ad Hoc Network Management Review
Group", RFC 1109, NRI, August 1989.
[3] Rose, M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", RFC 1155,
Performance Systems International and Hughes LAN Systems, May
1990.
[4] McCloghrie, K., and M. Rose, "Management Information Base for
Network Management of TCP/IP-based Internets", RFC 1156, Hughes
LAN Systems and Performance Systems International, May 1990.
[5] Case, J., M. Fedor, M. Schoffstall, and J. Davin, The Simple
Network Management Protocol", RFC 1157, University of Tennessee
at Knoxville, Performance Systems International, Performance
Systems International, and the MIT Laboratory for Computer
Science, May 1990.
[6] Rose, M., "Management Information Base for Network Management of
TCP/IP-based internets: MIB-II", RFC 1158, Performance Systems
International, May 1990.
[7] Information processing systems - Open Systems Interconnection,
"Specification of Abstract Syntax Notation One (ASN.1)",
International Organization for Standardization, International
Standard 8824, December 1987.
[8] Information processing systems - Open Systems Interconnection,
"Specification of Basic Encoding Rules for Abstract Notation One
(ASN.1)", International Organization for Standardization,
Satz [Page 69]
RFC 1162 CLNS MIB June 1990
International Standard 8825, December 1987.
[9] Information processing systems - Data Communications - "Protocol
for providing the Connectionless-mode Network Service and
Provision of Underlying Service", International Organization for
Standardization", International Standard 8473, May 1987.
[10] "End System to Intermediate System Routing Exchange Protocol for
Use in Conjunction with the Protocol for the Provision of the
Connectionless-mode Network Service (ISO 8473)", International
Draft Proposal 9542.
[11] Kille, S., "A String Encoding of Presentation Address", Research
Note RN/89/14, Department of Computer Science, University College
London, February 1989.
8. Security Considerations
Security issues are not discussed in this memo.
9. Author's Address:
Greg Satz
cisco Systems, Inc.
1350 Willow Road
Menlo Park, CA 94025
Phone: (415) 326-1941
Email: Satz@CISCO.COM
Satz [Page 70]