💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc3418.txt captured on 2022-01-08 at 18:39:46.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Network Working Group Editor of this version:
Request for Comments: 3418 R. Presuhn
STD: 62 BMC Software, Inc.
Obsoletes: 1907 Authors of previous version:
Category: Standards Track J. Case
SNMP Research, Inc.
K. McCloghrie
Cisco Systems, Inc.
M. Rose
Dover Beach Consulting, Inc.
S. Waldbusser
International Network Services
December 2002
Management Information Base (MIB) for the
Simple Network Management Protocol (SNMP)
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2002). All Rights Reserved.
Abstract
This document defines managed objects which describe the behavior of
a Simple Network Management Protocol (SNMP) entity. This document
obsoletes RFC 1907, Management Information Base for Version 2 of the
Simple Network Management Protocol (SNMPv2).
Presuhn, et al. Standards Track [Page 1]
RFC 3418 MIB for SNMP December 2002
Table of Contents
1. The Internet-Standard Management Framework .................. 2
2. Definitions ................................................. 2
3. Notice on Intellectual Property ............................. 20
4. Acknowledgments ............................................. 21
5. Security Considerations ..................................... 22
6. References .................................................. 23
6.1. Normative References ...................................... 23
6.2. Informative References .................................... 24
7. Changes from RFC 1907 ....................................... 24
8. Editor's Address ............................................ 25
9. Full Copyright Statement .................................... 26
1. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
It is the purpose of this document to define managed objects which
describe the behavior of an SNMP entity, as defined in the SNMP
architecture STD 62, [RFC3411].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in BCP 14, RFC 2119
[RFC2119].
2. Definitions
SNMPv2-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
TimeTicks, Counter32, snmpModules, mib-2
FROM SNMPv2-SMI
DisplayString, TestAndIncr, TimeStamp
Presuhn, et al. Standards Track [Page 2]
RFC 3418 MIB for SNMP December 2002
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF;
snmpMIB MODULE-IDENTITY
LAST-UPDATED "200210160000Z"
ORGANIZATION "IETF SNMPv3 Working Group"
CONTACT-INFO
"WG-EMail: snmpv3@lists.tislabs.com
Subscribe: snmpv3-request@lists.tislabs.com
Co-Chair: Russ Mundy
Network Associates Laboratories
postal: 15204 Omega Drive, Suite 300
Rockville, MD 20850-4601
USA
EMail: mundy@tislabs.com
phone: +1 301 947-7107
Co-Chair: David Harrington
Enterasys Networks
postal: 35 Industrial Way
P. O. Box 5005
Rochester, NH 03866-5005
USA
EMail: dbh@enterasys.com
phone: +1 603 337-2614
Editor: Randy Presuhn
BMC Software, Inc.
postal: 2141 North First Street
San Jose, CA 95131
USA
EMail: randy_presuhn@bmc.com
phone: +1 408 546-1006"
DESCRIPTION
"The MIB module for SNMP entities.
Copyright (C) The Internet Society (2002). This
version of this MIB module is part of RFC 3418;
see the RFC itself for full legal notices.
"
REVISION "200210160000Z"
DESCRIPTION
"This revision of this MIB module was published as
RFC 3418."
REVISION "199511090000Z"
DESCRIPTION
Presuhn, et al. Standards Track [Page 3]
RFC 3418 MIB for SNMP December 2002
"This revision of this MIB module was published as
RFC 1907."
REVISION "199304010000Z"
DESCRIPTION
"The initial revision of this MIB module was published
as RFC 1450."
::= { snmpModules 1 }
snmpMIBObjects OBJECT IDENTIFIER ::= { snmpMIB 1 }
-- ::= { snmpMIBObjects 1 } this OID is obsolete
-- ::= { snmpMIBObjects 2 } this OID is obsolete
-- ::= { snmpMIBObjects 3 } this OID is obsolete
-- the System group
--
-- a collection of objects common to all managed systems.
system OBJECT IDENTIFIER ::= { mib-2 1 }
sysDescr OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A textual description of the entity. This value should
include the full name and version identification of
the system's hardware type, software operating-system,
and networking software."
::= { system 1 }
sysObjectID OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor's authoritative identification of the
network management subsystem contained in the entity.
This value is allocated within the SMI enterprises
subtree (1.3.6.1.4.1) and provides an easy and
unambiguous means for determining `what kind of box' is
being managed. For example, if vendor `Flintstones,
Inc.' was assigned the subtree 1.3.6.1.4.1.424242,
it could assign the identifier 1.3.6.1.4.1.424242.1.1
to its `Fred Router'."
::= { system 2 }
sysUpTime OBJECT-TYPE
Presuhn, et al. Standards Track [Page 4]
RFC 3418 MIB for SNMP December 2002
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time (in hundredths of a second) since the
network management portion of the system was last
re-initialized."
::= { system 3 }
sysContact OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The textual identification of the contact person for
this managed node, together with information on how
to contact this person. If no contact information is
known, the value is the zero-length string."
::= { system 4 }
sysName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"An administratively-assigned name for this managed
node. By convention, this is the node's fully-qualified
domain name. If the name is unknown, the value is
the zero-length string."
::= { system 5 }
sysLocation OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The physical location of this node (e.g., 'telephone
closet, 3rd floor'). If the location is unknown, the
value is the zero-length string."
::= { system 6 }
sysServices OBJECT-TYPE
SYNTAX INTEGER (0..127)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A value which indicates the set of services that this
entity may potentially offer. The value is a sum.
Presuhn, et al. Standards Track [Page 5]
RFC 3418 MIB for SNMP December 2002
This sum initially takes the value zero. Then, for
each layer, L, in the range 1 through 7, that this node
performs transactions for, 2 raised to (L - 1) is added
to the sum. For example, a node which performs only
routing functions would have a value of 4 (2^(3-1)).
In contrast, a node which is a host offering application
services would have a value of 72 (2^(4-1) + 2^(7-1)).
Note that in the context of the Internet suite of
protocols, values should be calculated accordingly:
layer functionality
1 physical (e.g., repeaters)
2 datalink/subnetwork (e.g., bridges)
3 internet (e.g., supports the IP)
4 end-to-end (e.g., supports the TCP)
7 applications (e.g., supports the SMTP)
For systems including OSI protocols, layers 5 and 6
may also be counted."
::= { system 7 }
-- object resource information
--
-- a collection of objects which describe the SNMP entity's
-- (statically and dynamically configurable) support of
-- various MIB modules.
sysORLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time of the most recent
change in state or value of any instance of sysORID."
::= { system 8 }
sysORTable OBJECT-TYPE
SYNTAX SEQUENCE OF SysOREntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the capabilities of
the local SNMP application acting as a command
responder with respect to various MIB modules.
SNMP entities having dynamically-configurable support
of MIB modules will have a dynamically-varying number
of conceptual rows."
::= { system 9 }
Presuhn, et al. Standards Track [Page 6]
RFC 3418 MIB for SNMP December 2002
sysOREntry OBJECT-TYPE
SYNTAX SysOREntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the sysORTable."
INDEX { sysORIndex }
::= { sysORTable 1 }
SysOREntry ::= SEQUENCE {
sysORIndex INTEGER,
sysORID OBJECT IDENTIFIER,
sysORDescr DisplayString,
sysORUpTime TimeStamp
}
sysORIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The auxiliary variable used for identifying instances
of the columnar objects in the sysORTable."
::= { sysOREntry 1 }
sysORID OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An authoritative identification of a capabilities
statement with respect to various MIB modules supported
by the local SNMP application acting as a command
responder."
::= { sysOREntry 2 }
sysORDescr OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A textual description of the capabilities identified
by the corresponding instance of sysORID."
::= { sysOREntry 3 }
sysORUpTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
Presuhn, et al. Standards Track [Page 7]
RFC 3418 MIB for SNMP December 2002
STATUS current
DESCRIPTION
"The value of sysUpTime at the time this conceptual
row was last instantiated."
::= { sysOREntry 4 }
-- the SNMP group
--
-- a collection of objects providing basic instrumentation and
-- control of an SNMP entity.
snmp OBJECT IDENTIFIER ::= { mib-2 11 }
snmpInPkts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of messages delivered to the SNMP
entity from the transport service."
::= { snmp 1 }
snmpInBadVersions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of SNMP messages which were delivered
to the SNMP entity and were for an unsupported SNMP
version."
::= { snmp 3 }
snmpInBadCommunityNames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of community-based SNMP messages (for
example, SNMPv1) delivered to the SNMP entity which
used an SNMP community name not known to said entity.
Also, implementations which authenticate community-based
SNMP messages using check(s) in addition to matching
the community name (for example, by also checking
whether the message originated from a transport address
allowed to use a specified community name) MAY include
in this value the number of messages which failed the
additional check(s). It is strongly RECOMMENDED that
Presuhn, et al. Standards Track [Page 8]
RFC 3418 MIB for SNMP December 2002
the documentation for any security model which is used
to authenticate community-based SNMP messages specify
the precise conditions that contribute to this value."
::= { snmp 4 }
snmpInBadCommunityUses OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of community-based SNMP messages (for
example, SNMPv1) delivered to the SNMP entity which
represented an SNMP operation that was not allowed for
the SNMP community named in the message. The precise
conditions under which this counter is incremented
(if at all) depend on how the SNMP entity implements
its access control mechanism and how its applications
interact with that access control mechanism. It is
strongly RECOMMENDED that the documentation for any
access control mechanism which is used to control access
to and visibility of MIB instrumentation specify the
precise conditions that contribute to this value."
::= { snmp 5 }
snmpInASNParseErrs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of ASN.1 or BER errors encountered by
the SNMP entity when decoding received SNMP messages."
::= { snmp 6 }
snmpEnableAuthenTraps OBJECT-TYPE
SYNTAX INTEGER { enabled(1), disabled(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the SNMP entity is permitted to
generate authenticationFailure traps. The value of this
object overrides any configuration information; as such,
it provides a means whereby all authenticationFailure
traps may be disabled.
Note that it is strongly recommended that this object
be stored in non-volatile memory so that it remains
constant across re-initializations of the network
management system."
Presuhn, et al. Standards Track [Page 9]
RFC 3418 MIB for SNMP December 2002
::= { snmp 30 }
snmpSilentDrops OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of Confirmed Class PDUs (such as
GetRequest-PDUs, GetNextRequest-PDUs,
GetBulkRequest-PDUs, SetRequest-PDUs, and
InformRequest-PDUs) delivered to the SNMP entity which
were silently dropped because the size of a reply
containing an alternate Response Class PDU (such as a
Response-PDU) with an empty variable-bindings field
was greater than either a local constraint or the
maximum message size associated with the originator of
the request."
::= { snmp 31 }
snmpProxyDrops OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of Confirmed Class PDUs
(such as GetRequest-PDUs, GetNextRequest-PDUs,
GetBulkRequest-PDUs, SetRequest-PDUs, and
InformRequest-PDUs) delivered to the SNMP entity which
were silently dropped because the transmission of
the (possibly translated) message to a proxy target
failed in a manner (other than a time-out) such that
no Response Class PDU (such as a Response-PDU) could
be returned."
::= { snmp 32 }
-- information for notifications
--
-- a collection of objects which allow the SNMP entity, when
-- supporting a notification originator application,
-- to be configured to generate SNMPv2-Trap-PDUs.
snmpTrap OBJECT IDENTIFIER ::= { snmpMIBObjects 4 }
snmpTrapOID OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
Presuhn, et al. Standards Track [Page 10]
RFC 3418 MIB for SNMP December 2002
"The authoritative identification of the notification
currently being sent. This variable occurs as
the second varbind in every SNMPv2-Trap-PDU and
InformRequest-PDU."
::= { snmpTrap 1 }
-- ::= { snmpTrap 2 } this OID is obsolete
snmpTrapEnterprise OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The authoritative identification of the enterprise
associated with the trap currently being sent. When an
SNMP proxy agent is mapping an RFC1157 Trap-PDU
into a SNMPv2-Trap-PDU, this variable occurs as the
last varbind."
::= { snmpTrap 3 }
-- ::= { snmpTrap 4 } this OID is obsolete
-- well-known traps
snmpTraps OBJECT IDENTIFIER ::= { snmpMIBObjects 5 }
coldStart NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"A coldStart trap signifies that the SNMP entity,
supporting a notification originator application, is
reinitializing itself and that its configuration may
have been altered."
::= { snmpTraps 1 }
warmStart NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"A warmStart trap signifies that the SNMP entity,
supporting a notification originator application,
is reinitializing itself such that its configuration
is unaltered."
::= { snmpTraps 2 }
-- Note the linkDown NOTIFICATION-TYPE ::= { snmpTraps 3 }
-- and the linkUp NOTIFICATION-TYPE ::= { snmpTraps 4 }
-- are defined in RFC 2863 [RFC2863]
Presuhn, et al. Standards Track [Page 11]
RFC 3418 MIB for SNMP December 2002
authenticationFailure NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"An authenticationFailure trap signifies that the SNMP
entity has received a protocol message that is not
properly authenticated. While all implementations
of SNMP entities MAY be capable of generating this
trap, the snmpEnableAuthenTraps object indicates
whether this trap will be generated."
::= { snmpTraps 5 }
-- Note the egpNeighborLoss notification is defined
-- as { snmpTraps 6 } in RFC 1213
-- the set group
--
-- a collection of objects which allow several cooperating
-- command generator applications to coordinate their use of the
-- set operation.
snmpSet OBJECT IDENTIFIER ::= { snmpMIBObjects 6 }
snmpSetSerialNo OBJECT-TYPE
SYNTAX TestAndIncr
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"An advisory lock used to allow several cooperating
command generator applications to coordinate their
use of the SNMP set operation.
This object is used for coarse-grain coordination.
To achieve fine-grain coordination, one or more similar
objects might be defined within each MIB group, as
appropriate."
::= { snmpSet 1 }
-- conformance information
snmpMIBConformance
OBJECT IDENTIFIER ::= { snmpMIB 2 }
snmpMIBCompliances
OBJECT IDENTIFIER ::= { snmpMIBConformance 1 }
snmpMIBGroups OBJECT IDENTIFIER ::= { snmpMIBConformance 2 }
-- compliance statements
Presuhn, et al. Standards Track [Page 12]
RFC 3418 MIB for SNMP December 2002
-- ::= { snmpMIBCompliances 1 } this OID is obsolete
snmpBasicCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for SNMPv2 entities which
implement the SNMPv2 MIB.
This compliance statement is replaced by
snmpBasicComplianceRev2."
MODULE -- this module
MANDATORY-GROUPS { snmpGroup, snmpSetGroup, systemGroup,
snmpBasicNotificationsGroup }
GROUP snmpCommunityGroup
DESCRIPTION
"This group is mandatory for SNMPv2 entities which
support community-based authentication."
::= { snmpMIBCompliances 2 }
snmpBasicComplianceRev2 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities which
implement this MIB module."
MODULE -- this module
MANDATORY-GROUPS { snmpGroup, snmpSetGroup, systemGroup,
snmpBasicNotificationsGroup }
GROUP snmpCommunityGroup
DESCRIPTION
"This group is mandatory for SNMP entities which
support community-based authentication."
GROUP snmpWarmStartNotificationGroup
DESCRIPTION
"This group is mandatory for an SNMP entity which
supports command responder applications, and is
able to reinitialize itself such that its
configuration is unaltered."
::= { snmpMIBCompliances 3 }
-- units of conformance
-- ::= { snmpMIBGroups 1 } this OID is obsolete
-- ::= { snmpMIBGroups 2 } this OID is obsolete
-- ::= { snmpMIBGroups 3 } this OID is obsolete
Presuhn, et al. Standards Track [Page 13]
RFC 3418 MIB for SNMP December 2002
-- ::= { snmpMIBGroups 4 } this OID is obsolete
snmpGroup OBJECT-GROUP
OBJECTS { snmpInPkts,
snmpInBadVersions,
snmpInASNParseErrs,
snmpSilentDrops,
snmpProxyDrops,
snmpEnableAuthenTraps }
STATUS current
DESCRIPTION
"A collection of objects providing basic instrumentation
and control of an SNMP entity."
::= { snmpMIBGroups 8 }
snmpCommunityGroup OBJECT-GROUP
OBJECTS { snmpInBadCommunityNames,
snmpInBadCommunityUses }
STATUS current
DESCRIPTION
"A collection of objects providing basic instrumentation
of a SNMP entity which supports community-based
authentication."
::= { snmpMIBGroups 9 }
snmpSetGroup OBJECT-GROUP
OBJECTS { snmpSetSerialNo }
STATUS current
DESCRIPTION
"A collection of objects which allow several cooperating
command generator applications to coordinate their
use of the set operation."
::= { snmpMIBGroups 5 }
systemGroup OBJECT-GROUP
OBJECTS { sysDescr, sysObjectID, sysUpTime,
sysContact, sysName, sysLocation,
sysServices,
sysORLastChange, sysORID,
sysORUpTime, sysORDescr }
STATUS current
DESCRIPTION
"The system group defines objects which are common to all
managed systems."
::= { snmpMIBGroups 6 }
snmpBasicNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS { coldStart, authenticationFailure }
Presuhn, et al. Standards Track [Page 14]
RFC 3418 MIB for SNMP December 2002
STATUS current
DESCRIPTION
"The basic notifications implemented by an SNMP entity
supporting command responder applications."
::= { snmpMIBGroups 7 }
snmpWarmStartNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS { warmStart }
STATUS current
DESCRIPTION
"An additional notification for an SNMP entity supporting
command responder applications, if it is able to reinitialize
itself such that its configuration is unaltered."
::= { snmpMIBGroups 11 }
snmpNotificationGroup OBJECT-GROUP
OBJECTS { snmpTrapOID, snmpTrapEnterprise }
STATUS current
DESCRIPTION
"These objects are required for entities
which support notification originator applications."
::= { snmpMIBGroups 12 }
-- definitions in RFC 1213 made obsolete by the inclusion of a
-- subset of the snmp group in this MIB
snmpOutPkts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Messages which were
passed from the SNMP protocol entity to the
transport service."
::= { snmp 2 }
-- { snmp 7 } is not used
snmpInTooBigs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP PDUs which were
delivered to the SNMP protocol entity and for
which the value of the error-status field was
`tooBig'."
::= { snmp 8 }
Presuhn, et al. Standards Track [Page 15]
RFC 3418 MIB for SNMP December 2002
snmpInNoSuchNames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP PDUs which were
delivered to the SNMP protocol entity and for
which the value of the error-status field was
`noSuchName'."
::= { snmp 9 }
snmpInBadValues OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP PDUs which were
delivered to the SNMP protocol entity and for
which the value of the error-status field was
`badValue'."
::= { snmp 10 }
snmpInReadOnlys OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number valid SNMP PDUs which were delivered
to the SNMP protocol entity and for which the value
of the error-status field was `readOnly'. It should
be noted that it is a protocol error to generate an
SNMP PDU which contains the value `readOnly' in the
error-status field, as such this object is provided
as a means of detecting incorrect implementations of
the SNMP."
::= { snmp 11 }
snmpInGenErrs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP PDUs which were delivered
to the SNMP protocol entity and for which the value
of the error-status field was `genErr'."
::= { snmp 12 }
snmpInTotalReqVars OBJECT-TYPE
Presuhn, et al. Standards Track [Page 16]
RFC 3418 MIB for SNMP December 2002
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of MIB objects which have been
retrieved successfully by the SNMP protocol entity
as the result of receiving valid SNMP Get-Request
and Get-Next PDUs."
::= { snmp 13 }
snmpInTotalSetVars OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of MIB objects which have been
altered successfully by the SNMP protocol entity as
the result of receiving valid SNMP Set-Request PDUs."
::= { snmp 14 }
snmpInGetRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Get-Request PDUs which
have been accepted and processed by the SNMP
protocol entity."
::= { snmp 15 }
snmpInGetNexts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Get-Next PDUs which have been
accepted and processed by the SNMP protocol entity."
::= { snmp 16 }
snmpInSetRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Set-Request PDUs which
have been accepted and processed by the SNMP protocol
entity."
::= { snmp 17 }
Presuhn, et al. Standards Track [Page 17]
RFC 3418 MIB for SNMP December 2002
snmpInGetResponses OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Get-Response PDUs which
have been accepted and processed by the SNMP protocol
entity."
::= { snmp 18 }
snmpInTraps OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Trap PDUs which have been
accepted and processed by the SNMP protocol entity."
::= { snmp 19 }
snmpOutTooBigs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP PDUs which were generated
by the SNMP protocol entity and for which the value
of the error-status field was `tooBig.'"
::= { snmp 20 }
snmpOutNoSuchNames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP PDUs which were generated
by the SNMP protocol entity and for which the value
of the error-status was `noSuchName'."
::= { snmp 21 }
snmpOutBadValues OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP PDUs which were generated
by the SNMP protocol entity and for which the value
of the error-status field was `badValue'."
::= { snmp 22 }
Presuhn, et al. Standards Track [Page 18]
RFC 3418 MIB for SNMP December 2002
-- { snmp 23 } is not used
snmpOutGenErrs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP PDUs which were generated
by the SNMP protocol entity and for which the value
of the error-status field was `genErr'."
::= { snmp 24 }
snmpOutGetRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Get-Request PDUs which
have been generated by the SNMP protocol entity."
::= { snmp 25 }
snmpOutGetNexts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Get-Next PDUs which have
been generated by the SNMP protocol entity."
::= { snmp 26 }
snmpOutSetRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Set-Request PDUs which
have been generated by the SNMP protocol entity."
::= { snmp 27 }
snmpOutGetResponses OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Get-Response PDUs which
have been generated by the SNMP protocol entity."
::= { snmp 28 }
Presuhn, et al. Standards Track [Page 19]
RFC 3418 MIB for SNMP December 2002
snmpOutTraps OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The total number of SNMP Trap PDUs which have
been generated by the SNMP protocol entity."
::= { snmp 29 }
snmpObsoleteGroup OBJECT-GROUP
OBJECTS { snmpOutPkts, snmpInTooBigs, snmpInNoSuchNames,
snmpInBadValues, snmpInReadOnlys, snmpInGenErrs,
snmpInTotalReqVars, snmpInTotalSetVars,
snmpInGetRequests, snmpInGetNexts, snmpInSetRequests,
snmpInGetResponses, snmpInTraps, snmpOutTooBigs,
snmpOutNoSuchNames, snmpOutBadValues,
snmpOutGenErrs, snmpOutGetRequests, snmpOutGetNexts,
snmpOutSetRequests, snmpOutGetResponses, snmpOutTraps
}
STATUS obsolete
DESCRIPTION
"A collection of objects from RFC 1213 made obsolete
by this MIB module."
::= { snmpMIBGroups 10 }
END
3. Notice on Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Presuhn, et al. Standards Track [Page 20]
RFC 3418 MIB for SNMP December 2002
4. Acknowledgments
This document is the product of the SNMPv3 Working Group. Some
special thanks are in order to the following Working Group members:
Randy Bush
Jeffrey D. Case
Mike Daniele
Rob Frye
Lauren Heintz
Keith McCloghrie
Russ Mundy
David T. Perkins
Randy Presuhn
Aleksey Romanov
Juergen Schoenwaelder
Bert Wijnen
This version of the document, edited by Randy Presuhn, was initially
based on the work of a design team whose members were:
Jeffrey D. Case
Keith McCloghrie
David T. Perkins
Randy Presuhn
Juergen Schoenwaelder
The previous versions of this document, edited by Keith McCloghrie,
was the result of significant work by four major contributors:
Jeffrey D. Case
Keith McCloghrie
Marshall T. Rose
Steven Waldbusser
Presuhn, et al. Standards Track [Page 21]
RFC 3418 MIB for SNMP December 2002
Additionally, the contributions of the SNMPv2 Working Group to the
previous versions are also acknowledged. In particular, a special
thanks is extended for the contributions of:
Alexander I. Alten
Dave Arneson
Uri Blumenthal
Doug Book
Kim Curran
Jim Galvin
Maria Greene
Iain Hanson
Dave Harrington
Nguyen Hien
Jeff Johnson
Michael Kornegay
Deirdre Kostick
David Levi
Daniel Mahoney
Bob Natale
Brian O'Keefe
Andrew Pearson
Dave Perkins
Randy Presuhn
Aleksey Romanov
Shawn Routhier
Jon Saperia
Juergen Schoenwaelder
Bob Stewart
Kaj Tesink
Glenn Waters
Bert Wijnen
5. Security Considerations
There are a number of management objects defined in this MIB that
have a MAX-ACCESS clause of read-write. Such objects may be
considered sensitive or vulnerable in some network environments. The
support for SET operations in a non-secure environment without proper
protection can have a negative effect on network operations.
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and
GET/SET (read/change) the objects in this MIB.
Presuhn, et al. Standards Track [Page 22]
RFC 3418 MIB for SNMP December 2002
It is recommended that the implementors consider the security
features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model STD 62, RFC 3414 [RFC3414] and the
View-based Access Control Model STD 62, RFC 3415 [RFC3415] is
recommended.
It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB is properly
configured to give access to the objects only to those principals
(users) that have legitimate rights to indeed GET or SET (change)
them.
6. References
6.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April
1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999.
[RFC3411] Harrington, D., Presuhn, R. and B. Wijnen, "An
Architecture for describing Simple Network Management
Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
December 2002.
[RFC3414] Blumenthal, U. and B. Wijnen, "The User-Based Security
Model (USM) for Version 3 of the Simple Network
Management Protocol (SNMPv3)", STD 62, RFC 3414, December
2002.
[RFC3415] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", STD 62, RFC 3415, December
2002.
Presuhn, et al. Standards Track [Page 23]
RFC 3418 MIB for SNMP December 2002
6.1. Informative References
[RFC1157] Case, J., Fedor, M., Schoffstall, M. and J. Davin,
"Simple Network Management Protocol", STD 15, RFC 1157,
May 1990.
[RFC1213] McCloghrie, K. and M. Rose, "Management Information Base
for Network Management of TCP/IP-based internets: MIB-
II", STD 16, RFC 1213, March 1991.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
7. Changes from RFC 1907
These are the changes from RFC 1907:
- Corrected typo in copyright statement;
- Updated copyright date;
- Updated with new editor's name and contact information;
- Cosmetic fixes to layout and typography;
- Changed title;
- Replace introduction with current MIB boilerplate;
- Updated references;
- Fixed typo in sysORUpTime;
- Re-worded description of snmpSilentDrops;
- Updated reference to RFC 1573 to 2863;
- Added IPR boilerplate as required by RFC 2026;
- Weakened authenticationFailure description from MUST to MAY,
clarified that it pertains to all SNMP entities;
Presuhn, et al. Standards Track [Page 24]
RFC 3418 MIB for SNMP December 2002
- Clarified descriptions of snmpInBadCommunityNames and
snmpInBadCommunityUses;
- Updated module-identity and contact information;
- Updated the acknowledgments section;
- Replaced references to "manager role", "agent role" and "SNMPv2
entity" with appropriate terms from RFC 2571;
- Updated document headers and footers;
- Added security considerations, based on current recommendations
for MIB modules;
- Added NOTIFICATION-GROUP and OBJECT-GROUP constructs for
NOTIFICATION-TYPEs and OBJECT-TYPEs that were left unreferenced
in RFC 1907;
- Fixed typos in sysServices DESCRIPTION;
- Changed description of snmpProxyDrops to use terms from
architecture;
- Changed value used in example for sysObjectID;
- Added an abstract;
- Deprecated the snmpBasicCompliance MODULE-COMPLIANCE, and added
the snmpBasicComplianceRev2 MODULE-COMPLIANCE to take its
place;
- Updated working group mailing list address;
- Added co-chair's address.
8. Editor's Address
Randy Presuhn
BMC Software, Inc.
2141 North First Street
San Jose, CA 95131
USA
Phone: +1 408 546 1006
EMail: randy_presuhn@bmc.com
Presuhn, et al. Standards Track [Page 25]
RFC 3418 MIB for SNMP December 2002
9. Full Copyright Statement
Copyright (C) The Internet Society (2002). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Presuhn, et al. Standards Track [Page 26]