💾 Archived View for gmi.noulin.net › rfc › rfc1657.gmi captured on 2021-12-05 at 23:47:19. Gemini links have been rewritten to link to archived content
-=-=-=-=-=-=-
Obsoleted by:
Keywords: BGP-4-MIB, MIB, Management, Information, Base
Network Working Group S. Willis
Request for Comments: 1657 J. Burruss
Category: Standards Track Wellfleet Communications Inc.
J. Chu, Editor
IBM Corp.
July 1994
Definitions of Managed Objects for the Fourth Version of the
Border Gateway Protocol (BGP-4) using SMIv2
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects used for managing the
Border Gateway Protocol Version 4 or lower [1, 2].
2. The SNMPv2 Network Management Framework
The SNMPv2 Network Management Framework consists of four major
components. They are:
RFC 1442 which defines the SMI, the mechanisms used for describing
and naming objects for the purpose of management.
STD 17, RFC 1213 defines MIB-II, the core set of managed objects
forthe Internet suite of protocols.
RFC 1445 which defines the administrative and other architectural
aspects of the framework.
RFC 1448 which defines the protocol used for network access to
managed objects.
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
Willis, Burruss & Chu [Page 1]
RFC 1657 BGP-4 MIB July 1994
3. Object Definitions
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the subset of Abstract Syntax Notation One (ASN.1)
defined in the SMI. In particular, each object type is named by an
OBJECT IDENTIFIER, an administratively assigned name. The object
type together with an object instance serves to uniquely identify a
specific instantiation of the object. For human convenience, we
often use a textual string, termed the descriptor, to refer to the
object type.
4. Overview
These objects are used to control and manage a BGP-4 implementation.
Apart from a few system-wide scalar objects, this MIB is broken into
three tables: the BGP Peer Table, the BGP Received Path Attribute
Table, and the BGP-4 Received Path Attribute Table. The BGP Peer
Table contains information about state and current activity of
connections with the BGP peers. The Received Path Attribute Table
contains path attributes received from all peers running BGP version
3 or less. The BGP-4 Received Path Attribute Table contains path
attributes received from all BGP-4 peers. The actual attributes used
in determining a route are a subset of the received attribute tables
after local routing policy has been applied.
5. Definitions
BGP4-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
IpAddress, Integer32, Counter32, Gauge32
FROM SNMPv2-SMI
mib-2
FROM RFC1213-MIB;
bgp MODULE-IDENTITY
LAST-UPDATED "9405050000Z"
ORGANIZATION "IETF BGP Working Group"
CONTACT-INFO
" John Chu (Editor)
Postal: IBM Corp.
P.O.Box 218
Yorktown Heights, NY 10598
US
Willis, Burruss & Chu [Page 2]
RFC 1657 BGP-4 MIB July 1994
Tel: +1 914 945 3156
Fax: +1 914 945 2141
E-mail: jychu@watson.ibm.com"
DESCRIPTION
"The MIB module for BGP-4."
::= { mib-2 15 }
bgpVersion OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vector of supported BGP protocol version
numbers. Each peer negotiates the version
from this vector. Versions are identified
via the string of bits contained within this
object. The first octet contains bits 0 to
7, the second octet contains bits 8 to 15,
and so on, with the most significant bit
referring to the lowest bit number in the
octet (e.g., the MSB of the first octet
refers to bit 0). If a bit, i, is present
and set, then the version (i+1) of the BGP
is supported."
::= { bgp 1 }
bgpLocalAs OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local autonomous system number."
::= { bgp 2 }
-- BGP Peer table. This table contains, one entry per
-- BGP peer, information about the BGP peer.
bgpPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF BgpPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"BGP peer table. This table contains,
one entry per BGP peer, information about
the connections with BGP peers."
::= { bgp 3 }
Willis, Burruss & Chu [Page 3]
RFC 1657 BGP-4 MIB July 1994
bgpPeerEntry OBJECT-TYPE
SYNTAX BgpPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry containing information about the
connection with a BGP peer."
INDEX { bgpPeerRemoteAddr }
::= { bgpPeerTable 1 }
BgpPeerEntry ::= SEQUENCE {
bgpPeerIdentifier
IpAddress,
bgpPeerState
INTEGER,
bgpPeerAdminStatus
INTEGER,
bgpPeerNegotiatedVersion
Integer32,
bgpPeerLocalAddr
IpAddress,
bgpPeerLocalPort
INTEGER,
bgpPeerRemoteAddr
IpAddress,
bgpPeerRemotePort
INTEGER,
bgpPeerRemoteAs
INTEGER,
bgpPeerInUpdates
Counter32,
bgpPeerOutUpdates
Counter32,
bgpPeerInTotalMessages
Counter32,
bgpPeerOutTotalMessages
Counter32,
bgpPeerLastError
OCTET STRING,
bgpPeerFsmEstablishedTransitions
Counter32,
bgpPeerFsmEstablishedTime
Gauge32,
bgpPeerConnectRetryInterval
INTEGER,
bgpPeerHoldTime
INTEGER,
bgpPeerKeepAlive
Willis, Burruss & Chu [Page 4]
RFC 1657 BGP-4 MIB July 1994
INTEGER,
bgpPeerHoldTimeConfigured
INTEGER,
bgpPeerKeepAliveConfigured
INTEGER,
bgpPeerMinASOriginationInterval
INTEGER,
bgpPeerMinRouteAdvertisementInterval
INTEGER,
bgpPeerInUpdateElapsedTime
Gauge32
}
bgpPeerIdentifier OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The BGP Identifier of this entry's BGP
peer."
::= { bgpPeerEntry 1 }
bgpPeerState OBJECT-TYPE
SYNTAX INTEGER {
idle(1),
connect(2),
active(3),
opensent(4),
openconfirm(5),
established(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The BGP peer connection state."
::= { bgpPeerEntry 2 }
bgpPeerAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
stop(1),
start(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired state of the BGP connection.
A transition from 'stop' to 'start' will
cause the BGP Start Event to be generated.
Willis, Burruss & Chu [Page 5]
RFC 1657 BGP-4 MIB July 1994
A transition from 'start' to 'stop' will
cause the BGP Stop Event to be generated.
This parameter can be used to restart BGP
peer connections. Care should be used in
providing write access to this object
without adequate authentication."
::= { bgpPeerEntry 3 }
bgpPeerNegotiatedVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The negotiated version of BGP running
between the two peers."
::= { bgpPeerEntry 4 }
bgpPeerLocalAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local IP address of this entry's BGP
connection."
::= { bgpPeerEntry 5 }
bgpPeerLocalPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local port for the TCP connection
between the BGP peers."
::= { bgpPeerEntry 6 }
bgpPeerRemoteAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The remote IP address of this entry's BGP
peer."
::= { bgpPeerEntry 7 }
bgpPeerRemotePort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
Willis, Burruss & Chu [Page 6]
RFC 1657 BGP-4 MIB July 1994
DESCRIPTION
"The remote port for the TCP connection
between the BGP peers. Note that the
objects bgpPeerLocalAddr,
bgpPeerLocalPort, bgpPeerRemoteAddr and
bgpPeerRemotePort provide the appropriate
reference to the standard MIB TCP
connection table."
::= { bgpPeerEntry 8 }
bgpPeerRemoteAs OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The remote autonomous system number."
::= { bgpPeerEntry 9 }
bgpPeerInUpdates OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of BGP UPDATE messages
received on this connection. This object
should be initialized to zero (0) when the
connection is established."
::= { bgpPeerEntry 10 }
bgpPeerOutUpdates OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of BGP UPDATE messages
transmitted on this connection. This
object should be initialized to zero (0)
when the connection is established."
::= { bgpPeerEntry 11 }
bgpPeerInTotalMessages OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of messages received
from the remote peer on this connection.
This object should be initialized to zero
Willis, Burruss & Chu [Page 7]
RFC 1657 BGP-4 MIB July 1994
when the connection is established."
::= { bgpPeerEntry 12 }
bgpPeerOutTotalMessages OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of messages transmitted to
the remote peer on this connection. This
object should be initialized to zero when
the connection is established."
::= { bgpPeerEntry 13 }
bgpPeerLastError OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last error code and subcode seen by this
peer on this connection. If no error has
occurred, this field is zero. Otherwise, the
first byte of this two byte OCTET STRING
contains the error code, and the second byte
contains the subcode."
::= { bgpPeerEntry 14 }
bgpPeerFsmEstablishedTransitions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of times the BGP FSM
transitioned into the established state."
::= { bgpPeerEntry 15 }
bgpPeerFsmEstablishedTime OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This timer indicates how long (in
seconds) this peer has been in the
Established state or how long
since this peer was last in the
Established state. It is set to zero when
a new peer is configured or the router is
booted."
Willis, Burruss & Chu [Page 8]
RFC 1657 BGP-4 MIB July 1994
::= { bgpPeerEntry 16 }
bgpPeerConnectRetryInterval OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the
ConnectRetry timer. The suggested value
for this timer is 120 seconds."
::= { bgpPeerEntry 17 }
bgpPeerHoldTime OBJECT-TYPE
SYNTAX INTEGER ( 0 | 3..65535 )
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time interval in seconds for the Hold
Timer established with the peer. The
value of this object is calculated by this
BGP speaker by using the smaller of the
value in bgpPeerHoldTimeConfigured and the
Hold Time received in the OPEN message.
This value must be at lease three seconds
if it is not zero (0) in which case the
Hold Timer has not been established with
the peer, or, the value of
bgpPeerHoldTimeConfigured is zero (0)."
::= { bgpPeerEntry 18 }
bgpPeerKeepAlive OBJECT-TYPE
SYNTAX INTEGER ( 0 | 1..21845 )
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time interval in seconds for the KeepAlive
timer established with the peer. The value
of this object is calculated by this BGP
speaker such that, when compared with
bgpPeerHoldTime, it has the same
proportion as what
bgpPeerKeepAliveConfigured has when
compared with bgpPeerHoldTimeConfigured.
If the value of this object is zero (0),
it indicates that the KeepAlive timer has
not been established with the peer, or,
the value of bgpPeerKeepAliveConfigured is
zero (0)."
Willis, Burruss & Chu [Page 9]
RFC 1657 BGP-4 MIB July 1994
::= { bgpPeerEntry 19 }
bgpPeerHoldTimeConfigured OBJECT-TYPE
SYNTAX INTEGER ( 0 | 3..65535 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the Hold Time
configured for this BGP speaker with this
peer. This value is placed in an OPEN
message sent to this peer by this BGP
speaker, and is compared with the Hold
Time field in an OPEN message received
from the peer when determining the Hold
Time (bgpPeerHoldTime) with the peer.
This value must not be less than three
seconds if it is not zero (0) in which
case the Hold Time is NOT to be
established with the peer. The suggested
value for this timer is 90 seconds."
::= { bgpPeerEntry 20 }
bgpPeerKeepAliveConfigured OBJECT-TYPE
SYNTAX INTEGER ( 0 | 1..21845 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the
KeepAlive timer configured for this BGP
speaker with this peer. The value of this
object will only determine the
KEEPALIVE messages' frequency relative to
the value specified in
bgpPeerHoldTimeConfigured; the actual
time interval for the KEEPALIVE messages
is indicated by bgpPeerKeepAlive. A
reasonable maximum value for this timer
would be configured to be one
third of that of
bgpPeerHoldTimeConfigured.
If the value of this object is zero (0),
no periodical KEEPALIVE messages are sent
to the peer after the BGP connection has
been established. The suggested value for
this timer is 30 seconds."
::= { bgpPeerEntry 21 }
Willis, Burruss & Chu [Page 10]
RFC 1657 BGP-4 MIB July 1994
bgpPeerMinASOriginationInterval OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the
MinASOriginationInterval timer.
The suggested value for this timer is 15
seconds."
::= { bgpPeerEntry 22 }
bgpPeerMinRouteAdvertisementInterval OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the
MinRouteAdvertisementInterval timer.
The suggested value for this timer is 30
seconds."
::= { bgpPeerEntry 23 }
bgpPeerInUpdateElapsedTime OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Elapsed time in seconds since the last BGP
UPDATE message was received from the peer.
Each time bgpPeerInUpdates is incremented,
the value of this object is set to zero
(0)."
::= { bgpPeerEntry 24 }
bgpIdentifier OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The BGP Identifier of local system."
::= { bgp 4 }
Willis, Burruss & Chu [Page 11]
RFC 1657 BGP-4 MIB July 1994
-- Received Path Attribute Table. This table contains,
-- one entry per path to a network, path attributes
-- received from all peers running BGP version 3 or
-- less. This table is deprecated.
bgpRcvdPathAttrTable OBJECT-TYPE
SYNTAX SEQUENCE OF BgpPathAttrEntry
MAX-ACCESS not-accessible
STATUS obsolete
DESCRIPTION
"The BGP Received Path Attribute Table
contains information about paths to
destination networks received from all
peers running BGP version 3 or less."
::= { bgp 5 }
bgpPathAttrEntry OBJECT-TYPE
SYNTAX BgpPathAttrEntry
MAX-ACCESS not-accessible
STATUS obsolete
DESCRIPTION
"Information about a path to a network."
INDEX { bgpPathAttrDestNetwork,
bgpPathAttrPeer }
::= { bgpRcvdPathAttrTable 1 }
BgpPathAttrEntry ::= SEQUENCE {
bgpPathAttrPeer
IpAddress,
bgpPathAttrDestNetwork
IpAddress,
bgpPathAttrOrigin
INTEGER,
bgpPathAttrASPath
OCTET STRING,
bgpPathAttrNextHop
IpAddress,
bgpPathAttrInterASMetric
Integer32
}
bgpPathAttrPeer OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The IP address of the peer where the path
information was learned."
Willis, Burruss & Chu [Page 12]
RFC 1657 BGP-4 MIB July 1994
::= { bgpPathAttrEntry 1 }
bgpPathAttrDestNetwork OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The address of the destination network."
::= { bgpPathAttrEntry 2 }
bgpPathAttrOrigin OBJECT-TYPE
SYNTAX INTEGER {
igp(1),-- networks are interior
egp(2),-- networks learned via EGP
incomplete(3) -- undetermined
}
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The ultimate origin of the path information."
::= { bgpPathAttrEntry 3 }
bgpPathAttrASPath OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2..255))
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The set of ASs that must be traversed to
reach the network. This object is
probably best represented as SEQUENCE OF
INTEGER. For SMI compatibility, though,
it is represented as OCTET STRING. Each
AS is represented as a pair of octets
according to the following algorithm:
first-byte-of-pair = ASNumber / 256;
second-byte-of-pair = ASNumber & 255;"
::= { bgpPathAttrEntry 4 }
bgpPathAttrNextHop OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The address of the border router that
should be used for the destination
network."
::= { bgpPathAttrEntry 5 }
Willis, Burruss & Chu [Page 13]
RFC 1657 BGP-4 MIB July 1994
bgpPathAttrInterASMetric OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The optional inter-AS metric. If this
attribute has not been provided for this
route, the value for this object is 0."
::= { bgpPathAttrEntry 6 }
-- BGP-4 Received Path Attribute Table. This table
-- contains, one entry per path to a network, path
-- attributes received from all peers running BGP-4.
bgp4PathAttrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Bgp4PathAttrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The BGP-4 Received Path Attribute Table
contains information about paths to
destination networks received from all
BGP4 peers."
::= { bgp 6 }
bgp4PathAttrEntry OBJECT-TYPE
SYNTAX Bgp4PathAttrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a path to a network."
INDEX { bgp4PathAttrIpAddrPrefix,
bgp4PathAttrIpAddrPrefixLen,
bgp4PathAttrPeer }
::= { bgp4PathAttrTable 1 }
Bgp4PathAttrEntry ::= SEQUENCE {
bgp4PathAttrPeer
IpAddress,
bgp4PathAttrIpAddrPrefixLen
INTEGER,
bgp4PathAttrIpAddrPrefix
IpAddress,
bgp4PathAttrOrigin
INTEGER,
bgp4PathAttrASPathSegment
Willis, Burruss & Chu [Page 14]
RFC 1657 BGP-4 MIB July 1994
OCTET STRING,
bgp4PathAttrNextHop
IpAddress,
bgp4PathAttrMultiExitDisc
INTEGER,
bgp4PathAttrLocalPref
INTEGER,
bgp4PathAttrAtomicAggregate
INTEGER,
bgp4PathAttrAggregatorAS
INTEGER,
bgp4PathAttrAggregatorAddr
IpAddress,
bgp4PathAttrCalcLocalPref
INTEGER,
bgp4PathAttrBest
INTEGER,
bgp4PathAttrUnknown
OCTET STRING
}
bgp4PathAttrPeer OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of the peer where the path
information was learned."
::= { bgp4PathAttrEntry 1 }
bgp4PathAttrIpAddrPrefixLen OBJECT-TYPE
SYNTAX INTEGER (0..32)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Length in bits of the IP address prefix
in the Network Layer Reachability
Information field."
::= { bgp4PathAttrEntry 2 }
bgp4PathAttrIpAddrPrefix OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An IP address prefix in the Network Layer
Reachability Information field. This object
Willis, Burruss & Chu [Page 15]
RFC 1657 BGP-4 MIB July 1994
is an IP address containing the prefix with
length specified by
bgp4PathAttrIpAddrPrefixLen.
Any bits beyond the length specified by
bgp4PathAttrIpAddrPrefixLen are zeroed."
::= { bgp4PathAttrEntry 3 }
bgp4PathAttrOrigin OBJECT-TYPE
SYNTAX INTEGER {
igp(1),-- networks are interior
egp(2),-- networks learned
-- via EGP
incomplete(3) -- undetermined
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ultimate origin of the path
information."
::= { bgp4PathAttrEntry 4 }
bgp4PathAttrASPathSegment OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence of AS path segments. Each AS
path segment is represented by a triple
<type, length, value>.
The type is a 1-octet field which has two
possible values:
1 AS_SET: unordered set of ASs a
route in the UPDATE
message has traversed
2 AS_SEQUENCE: ordered set of ASs
a route in the UPDATE
message has traversed.
The length is a 1-octet field containing the
number of ASs in the value field.
The value field contains one or more AS
numbers, each AS is represented in the octet
string as a pair of octets according to the
following algorithm:
Willis, Burruss & Chu [Page 16]
RFC 1657 BGP-4 MIB July 1994
first-byte-of-pair = ASNumber / 256;
second-byte-of-pair = ASNumber & 255;"
::= { bgp4PathAttrEntry 5 }
bgp4PathAttrNextHop OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of the border router that
should be used for the destination
network."
::= { bgp4PathAttrEntry 6 }
bgp4PathAttrMultiExitDisc OBJECT-TYPE
SYNTAX INTEGER (-1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This metric is used to discriminate
between multiple exit points to an
adjacent autonomous system. A value of -1
indicates the absence of this attribute."
::= { bgp4PathAttrEntry 7 }
bgp4PathAttrLocalPref OBJECT-TYPE
SYNTAX INTEGER (-1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The originating BGP4 speaker's degree of
preference for an advertised route. A
value of -1 indicates the absence of this
attribute."
::= { bgp4PathAttrEntry 8 }
bgp4PathAttrAtomicAggregate OBJECT-TYPE
SYNTAX INTEGER {
lessSpecificRrouteNotSelected(1),
lessSpecificRouteSelected(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether or not the local system has
selected a less specific route without
selecting a more specific route."
::= { bgp4PathAttrEntry 9 }
Willis, Burruss & Chu [Page 17]
RFC 1657 BGP-4 MIB July 1994
bgp4PathAttrAggregatorAS OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The AS number of the last BGP4 speaker that
performed route aggregation. A value of
zero (0) indicates the absence of this
attribute."
::= { bgp4PathAttrEntry 10 }
bgp4PathAttrAggregatorAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of the last BGP4 speaker
that performed route aggregation. A value
of 0.0.0.0 indicates the absence of this
attribute."
::= { bgp4PathAttrEntry 11 }
bgp4PathAttrCalcLocalPref OBJECT-TYPE
SYNTAX INTEGER (-1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The degree of preference calculated by the
receiving BGP4 speaker for an advertised
route. A value of -1 indicates the
absence of this attribute."
::= { bgp4PathAttrEntry 12 }
bgp4PathAttrBest OBJECT-TYPE
SYNTAX INTEGER {
false(1),-- not chosen as best route
true(2) -- chosen as best route
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether or not this route
was chosen as the best BGP4 route."
::= { bgp4PathAttrEntry 13 }
bgp4PathAttrUnknown OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..255))
MAX-ACCESS read-only
Willis, Burruss & Chu [Page 18]
RFC 1657 BGP-4 MIB July 1994
STATUS current
DESCRIPTION
"One or more path attributes not understood
by this BGP4 speaker. Size zero (0)
indicates the absence of such
attribute(s). Octets beyond the maximum
size, if any, are not recorded by this
object."
::= { bgp4PathAttrEntry 14 }
-- Traps.
bgpTraps OBJECT IDENTIFIER ::= { bgp 7 }
bgpEstablished NOTIFICATION-TYPE
OBJECTS { bgpPeerLastError,
bgpPeerState }
STATUS current
DESCRIPTION
"The BGP Established event is generated when
the BGP FSM enters the ESTABLISHED state."
::= { bgpTraps 1 }
bgpBackwardTransition NOTIFICATION-TYPE
OBJECTS { bgpPeerLastError,
bgpPeerState }
STATUS current
DESCRIPTION
"The BGPBackwardTransition Event is generated
when the BGP FSM moves from a higher numbered
state to a lower numbered state."
::= { bgpTraps 2 }
END
Willis, Burruss & Chu [Page 19]
RFC 1657 BGP-4 MIB July 1994
6. Acknowledgements
We would like to acknowledge the assistance of all the members of the
Interconnectivity Working Group, and particularly the following
individuals:
Yakov Rekhter, IBM
Rob Coltun, University of Maryland
Guy Almes, ANS
Jeff Honig, Cornell Theory Center
Marshall T. Rose, Dover Beach Consulting, Inc.
Dennis Ferguson, ANS
Mike Mathis, PSC
John Krawczyk, Wellfleet Communications Inc.
Curtis Villamizar, ANS
Dave LeRoy, Pencom Systems
Paul Traina, cisco Systems
Andrew Partan, UUNET
Robert Snyder, cisco Systems
Dimitry Haskin, Wellfleet Communications Inc.
Peder Chr Norgaard, Telebit Communications A/S
Joel Halpern, Network Systems Corporation
7. References
[1] Rekhter, Y., and T. Li, "A Border Gateway Protocol 4 (BGP-4)",
RFC 1654, T.J. Watson Research Center, IBM Corp., cisco Systems,
July 1994.
[2] Rekhter, Y., and P. Gross, Editors, "Application of the Border
Gateway Protocol in the Internet", RFC 1655 T.J. Watson Research
Center, IBM Corp., MCI, July 1994.
8. Security Considerations
Security issues are not discussed in this memo.
Willis, Burruss & Chu [Page 20]
RFC 1657 BGP-4 MIB July 1994
9. Authors' Addresses
Steven Willis
Wellfleet Communications Inc.
15 Crosby Drive
Bedford, MA 01730
Phone: (617) 275-2400
EMail: swillis@wellfleet.com
John Burruss
Wellfleet Communications Inc.
15 Crosby Drive
Bedford, MA 01730
Phone: (617) 275-2400
EMail: jburruss@wellfleet.com
John Chu
IBM Corp.
P.O.Box 218
Yorktown Heights, NY 10598
Phone: (914) 945-3156
EMail: jychu@watson.ibm.com
Willis, Burruss & Chu [Page 21]