💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc8950.txt captured on 2021-12-04 at 18:04:22.
⬅️ Previous capture (2021-11-30)
-=-=-=-=-=-=-
Internet Engineering Task Force (IETF) S. Litkowski
Request for Comments: 8950 S. Agrawal
Obsoletes: 5549 K. Ananthamurthy
Category: Standards Track Cisco
ISSN: 2070-1721 K. Patel
Arrcus
November 2020
Advertising IPv4 Network Layer Reachability Information (NLRI) with an
IPv6 Next Hop
Abstract
Multiprotocol BGP (MP-BGP) specifies that the set of usable next-hop
address families is determined by the Address Family Identifier (AFI)
and the Subsequent Address Family Identifier (SAFI). The AFI/SAFI
definitions for the IPv4 address family only have provisions for
advertising a next-hop address that belongs to the IPv4 protocol when
advertising IPv4 Network Layer Reachability Information (NLRI) or
VPN-IPv4 NLRI.
This document specifies the extensions necessary to allow the
advertising of IPv4 NLRI or VPN-IPv4 NLRI with a next-hop address
that belongs to the IPv6 protocol. This comprises an extension of
the AFI/SAFI definitions to allow the address of the next hop for
IPv4 NLRI or VPN-IPv4 NLRI to also belong to the IPv6 protocol, the
encoding of the next hop to determine which of the protocols the
address actually belongs to, and a BGP Capability allowing MP-BGP
peers to dynamically discover whether they can exchange IPv4 NLRI and
VPN-IPv4 NLRI with an IPv6 next hop. This document obsoletes RFC
5549.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
https://www.rfc-editor.org/info/rfc8950.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction
1.1. Requirements Language
2. Changes Compared to RFC 5549
3. Extension of AFI/SAFI Definitions for the IPv4 Address Family
4. Use of BGP Capability Advertisement
5. Operations
6. Usage Examples
6.1. IPv4 over IPv6 Core
6.2. IPv4 VPN Unicast over IPv6 Core
6.3. IPv4 VPN Multicast over IPv6 Core
7. IANA Considerations
8. Security Considerations
9. References
9.1. Normative References
9.2. Informative References
Acknowledgments
Authors' Addresses
1. Introduction
Multiprotocol BGP (MP-BGP) [RFC4760] specifies that the set of
network-layer protocols to which the address carried in the Next Hop
Address field may belong is determined by the Address Family
Identifier (AFI) and the Subsequent Address Family Identifier (SAFI).
A number of existing AFIs/SAFIs allow the next-hop address to belong
to a different address family than the Network Layer Reachability
Information (NLRI). For example, the AFI/SAFI <25/65> used (as per
[RFC6074]) to perform Layer 2 Virtual Private Network (L2VPN) auto-
discovery allows advertising NLRI that contains the identifier of a
Virtual Private LAN Service (VPLS) instance or that identifies a
particular pool of attachment circuits at a given Provider Edge (PE),
while the Next Hop Address field contains the loopback address of a
PE. Similarly, the AFI/SAFI <1/132> (defined in [RFC4684]) to
advertise Route Target (RT) membership information allows advertising
NLRI that contains such RT membership information, while the Next Hop
Address field contains the address of the advertising router.
Furthermore, a number of these existing AFIs/SAFIs allow the next hop
to belong to either the IPv4 protocol or the IPv6 protocol and
specify the encoding of the next-hop information to determine which
of the protocols the address actually belongs to. For example,
[RFC4684] allows the next-hop address to be either an IPv4 or IPv6
address and states that the Next Hop Address field shall be
interpreted as an IPv4 address whenever the length of the next-hop
address is 4 octets and as an IPv6 address whenever the length of the
next-hop address is 16 octets.
There are situations such as those described in [RFC4925] and
[RFC5565] where carriers (or large enterprise networks acting as a
carrier for their internal resources) may be required to establish
connectivity between 'islands' of networks of one address family type
across a transit core of a differing address family type. This
includes both the case of IPv6 islands across an IPv4 core and the
case of IPv4 islands across an IPv6 core. Where Multiprotocol BGP
(MP-BGP) is used to advertise the corresponding reachability
information, this translates into the requirement for a BGP speaker
to advertise the NLRI of a given address family via a next hop of a
different address family (i.e., IPv6 NLRI with an IPv4 next hop and
IPv4 NLRI with an IPv6 next hop).
The AFI/SAFI definitions for the IPv6 address family assume that the
next-hop address belongs to the IPv6 address family type.
Specifically, as per [RFC2545] and [RFC8277], when the <AFI/SAFI> is
<2/1>, <2/2>, or <2/4>, the next-hop address is assumed to be of an
IPv6 type. As per [RFC4659], when the <AFI/SAFI> is <2/128>, the
next-hop address is assumed to be of a VPN-IPv6 type.
However, [RFC4798] and [RFC4659] specify how an IPv4 address can be
encoded inside the next-hop IPv6 address field when IPv6 NLRI needs
to be advertised with an IPv4 next hop. [RFC4798] defines how the
IPv4-mapped IPv6 address format specified in the IPv6 addressing
architecture ([RFC4291]) can be used for that purpose when the <AFI/
SAFI> is <2/1>, <2/2>, or <2/4>. [RFC4659] defines how the
IPv4-mapped IPv6 address format as well as a null Route Distinguisher
(RD) can be used for that purpose when the <AFI/SAFI> is <2/128>.
Thus, there are existing solutions for the advertisement of IPv6 NLRI
with an IPv4 next hop.
Similarly, the AFI/SAFI definitions for the advertisement of IPv4
NLRI or VPN-IPv4 NLRI assume that the next-hop address belongs to the
IPv4 address family type. Specifically, as per [RFC4760] and
[RFC8277], when the <AFI/SAFI> is <1/1>, <1/2>, or <1/4>, the next-
hop address is assumed to be of an IPv4 type. As per [RFC4364], when
the <AFI/SAFI> is <1/128>, the next-hop address is assumed to be of a
VPN-IPv4 type. As per [RFC6513] and [RFC6514], when the <AFI/SAFI>
is <1/129>, the next-hop address is assumed to be of a VPN-IPv4 type.
There is clearly no generally applicable method for encoding an IPv6
address inside the IPv4 address field of the next hop. Hence, there
is currently no specified solution for advertising IPv4 or VPN-IPv4
NLRI with an IPv6 next hop.
This document specifies the extensions necessary to allow
advertisement of IPv4 NLRI or VPN-IPv4 NLRI with a next-hop address
that belongs to the IPv6 protocol. This comprises an extension of
the AFI/SAFI definitions to allow the address of the next hop for
IPv4 NLRI or VPN-IPv4 NLRI to belong to either the IPv4 or the IPv6
protocol, the encoding of the next-hop information to determine which
of the protocols the address actually belongs to, and a BGP
Capability allowing MP-BGP peers to dynamically discover whether they
can exchange IPv4 NLRI and VPN-IPv4 NLRI with an IPv6 next hop. The
BGP Capability allows gradual deployment of the functionality of
advertising IPv4 reachability via an IPv6 next hop without any flag
day nor any risk of traffic black-holing.
This document obsoletes [RFC5549].
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
2. Changes Compared to RFC 5549
This document introduces two significant changes compared to
[RFC5549]:
* In [RFC5549], when AFI/SAFI <1/128> is used, the next-hop address
is encoded as an IPv6 address with a length of 16 or 32 bytes. To
accommodate all existing implementations and bring consistency
with VPNv4oIPv4 and VPNv6oIPv6, this document modifies how the
next-hop address is encoded. The next-hop address is now encoded
as a VPN-IPv6 address with a length of 24 or 48 bytes (see
Sections 3 and 6.2). This change addresses Erratum ID 5253
([Err5253]). As all known and deployed implementations are
interoperable today and use the new proposed encoding, the change
does not break existing interoperability.
* This document allows AFI/SAFI <1/129> (IPv4 multicast) to use an
IPv6 underlay using similar encoding and procedures to AFI/SAFI
<1/128> (see Sections 3 and 6.3).
3. Extension of AFI/SAFI Definitions for the IPv4 Address Family
As mentioned earlier, MP-BGP specifies that the set of usable next-
hop address families is determined by the AFI and the SAFI. The
following AFI/SAFI definitions for the IPv4 NLRI or VPN-IPv4 NLRI
(<1/1>, <1/2>, <1/4>, <1/128>, and <1/129>) only have provisions for
advertising a next-hop address that belongs to the IPv4 protocol.
This document extends the set of usable next-hop address families to
include IPv6 in addition to IPv4 when advertising an IPv4 or VPN-IPv4
NLRI.
Specifically, this document allows advertising the MP_REACH_NLRI
attribute [RFC4760] with this content:
* AFI = 1
* SAFI = 1, 2, or 4
* Length of Next Hop Address = 16 or 32
* Next Hop Address = IPv6 address of a next hop (potentially
followed by the link-local IPv6 address of the next hop). This
field is to be constructed as per Section 3 of [RFC2545].
* NLRI = NLRI as per the AFI/SAFI definition
It also allows advertising the MP_REACH_NLRI attribute [RFC4760] with
this content:
* AFI = 1
* SAFI = 128 or 129
* Length of Next Hop Address = 24 or 48
* Next Hop Address = VPN-IPv6 address of a next hop with an 8-octet
RD set to zero (potentially followed by the link-local VPN-IPv6
address of the next hop with an 8-octet RD set to zero).
* NLRI = NLRI as per the AFI/SAFI definition
This is in addition to the existing mode of operation allowing
advertisement of NLRI for <AFI/SAFI> of <1/1>, <1/2>, and <1/4> with
a next-hop address of an IPv4 type and advertisement of NLRI for an
<AFI/SAFI> of <1/128> and <1/129> with a next-hop address of a VPN-
IPv4 type.
The BGP speaker receiving the advertisement MUST use the Length of
Next Hop Address field to determine which network-layer protocol the
next-hop address belongs to.
* When the AFI/SAFI is <1/1>, <1/2>, or <1/4> and when the Length of
Next Hop Address field is equal to 16 or 32, the next-hop address
is of type IPv6.
* When the AFI/SAFI is <1/128> or <1/129> and when the Length of
Next Hop Address field is equal to 24 or 48, the next-hop address
is of type VPN-IPv6.
Note that this method of using the Length of Next Hop Address field
to determine which network-layer protocol the next-hop address
belongs to (out of the set of protocols allowed by the AFI/SAFI
definition) is the same as that used in [RFC4684] and [RFC6074].
4. Use of BGP Capability Advertisement
[RFC5492] defines a mechanism to allow two BGP speakers to discover
if a particular capability is supported by their BGP peer and, thus,
whether it can be used with that peer. This document defines a
capability that can be advertised using [RFC5492], referred to as the
"Extended Next Hop Encoding capability". This capability allows BGP
speakers to discover whether, for a given NLRI <AFI/SAFI>, a peer
supports advertisement with a next hop whose network protocol is
determined by the value of the Length of Next Hop Address field, as
specified in Section 3.
A BGP speaker that wishes to advertise an IPv6 next hop for IPv4 NLRI
or for VPN-IPv4 NLRI to a BGP peer as per this specification MUST use
the Capability Advertisement procedures defined in [RFC5492] with the
Extended Next Hop Encoding capability to determine whether its peer
supports this for the NLRI AFI/SAFI pair(s) of interest. The fields
in the Capabilities Optional Parameter MUST be set as follows:
* The Capability Code field MUST be set to 5 (which indicates the
Extended Next Hop Encoding capability).
* The Capability Length field is set to a variable value that is the
length of the Capability Value field (which follows).
* The Capability Value field has the following format:
+-----------------------------------------------------+
| NLRI AFI - 1 (2 octets) |
+-----------------------------------------------------+
| NLRI SAFI - 1 (2 octets) |
+-----------------------------------------------------+
| Nexthop AFI - 1 (2 octets) |
+-----------------------------------------------------+
| ..... |
+-----------------------------------------------------+
| NLRI AFI - N (2 octets) |
+-----------------------------------------------------+
| NLRI SAFI - N (2 octets) |
+-----------------------------------------------------+
| Nexthop AFI - N (2 octets) |
+-----------------------------------------------------+
where:
- each triple <NLRI AFI, NLRI SAFI, Nexthop AFI> indicates that
the NLRI of <NLRI AFI / NLRI SAFI> may be advertised with a
next-hop address belonging to the network-layer protocol of
Nexthop AFI.
- the AFI and SAFI values are defined in the "Address Family
Numbers" and "Subsequent Address Family Identifier (SAFI)
Parameters" registries (see [IANA-AFI] and [IANA-SAFI],
respectively).
Since this document only concerns itself with the advertisement of
IPv4 NLRI and VPN-IPv4 NLRI with an IPv6 next hop, this specification
only allows the following values in the Capability Value field of the
Extended Next Hop Encoding capability:
* NLRI AFI = 1 (IPv4)
* NLRI SAFI = 1, 2, 4, 128, or 129
* Nexthop AFI = 2 (IPv6)
This document does not specify the use of the Extended Next Hop
Encoding capability with any other combinations of <NLRI AFI, NLRI
SAFI, Nexthop AFI>. For example, the Next Hop Encoding capability
specified in this document is not intended to be used for NLRI AFIs/
SAFIs whose definition already allows use of both IPv4 and IPv6 next
hops (e.g., AFI/SAFI = <1/132> as defined in [RFC4684]). Similarly,
it is not intended that the Extended Next Hop Encoding capability be
used for NLRI AFIs/SAFIs for which there is already a solution for
advertising a next hop of a different address family (e.g., AFI/SAFI
= <2/1>, <2/2>, or <2/4> with an IPv4 next hop as per [RFC4798] and
AFI/SAFI = <2/128> with an IPv4 next hop as per [RFC4659]).
It is expected that if new AFIs/SAFIs are defined in the future,
their definitions will have provisions (where appropriate) for both
IPv4 and IPv6 next hops from the beginning, with the determination
based on the Length of Next Hop Address field. Thus, new AFIs/SAFIs
are not expected to make use of the Extended Next Hop Encoding
capability.
A BGP speaker MUST only advertise the IPv4 or VPN-IPv4 NLRI with an
IPv6 next hop to a BGP peer if the BGP speaker has first ascertained
via the BGP Capability Advertisement that the BGP peer supports the
Extended Next Hop Encoding capability for the relevant AFI/SAFI pair.
The Extended Next Hop Encoding capability provides information about
next-hop encoding for a given AFI/SAFI, assuming that AFI/SAFI is
allowed. It does not influence whether that AFI/SAFI is indeed
allowed. Whether an AFI/SAFI can be used between the BGP peers is
purely determined through the Multiprotocol Extensions capability
defined in [RFC4760].
5. Operations
By default, if a particular BGP session is running over IPvx (where
IPvx is IPv4 or IPv6) and if the BGP speaker sending an update is
putting its own address in as the next hop, then the next-hop address
SHOULD be specified as an IPvx address, using the encoding rules
specified in the AFI/SAFI definition of the NLRI being updated. This
default behavior may be overridden by policy.
When a next-hop address needs to be passed along unchanged (e.g., as
a Route Reflector (RR) would do), its encoding MUST NOT be changed.
If a particular RR client cannot handle that encoding (as determined
by the BGP Capability Advertisement), then the NLRI in question
cannot be distributed to that client. For sound routing in certain
scenarios, this will require that all the RR clients be able to
handle whatever encodings any of them may generate.
6. Usage Examples
6.1. IPv4 over IPv6 Core
The extensions defined in this document may be used as discussed in
[RFC5565] for the interconnection of IPv4 islands over an IPv6
backbone. In this application, Address Family Border Routers (AFBRs;
as defined in [RFC4925]) advertise IPv4 NLRI in the MP_REACH_NLRI
along with an IPv6 next hop.
The MP_REACH_NLRI is encoded with:
* AFI = 1
* SAFI = 1
* Length of Next Hop Address field = 16 (or 32)
* Next Hop Address = IPv6 address of the next hop
* NLRI = IPv4 routes
During BGP Capability Advertisement, the PE routers would include the
following fields in the Capabilities Optional Parameter:
* Capability Code set to "Extended Next Hop Encoding"
* Capability Value containing <NLRI AFI=1, NLRI SAFI=1, Nexthop
AFI=2>
6.2. IPv4 VPN Unicast over IPv6 Core
The extensions defined in this document may be used for support of
IPv4 VPNs over an IPv6 backbone. In this application, PE routers
would advertise VPN-IPv4 NLRI in the MP_REACH_NLRI along with an IPv6
next hop.
The MP_REACH_NLRI is encoded with:
* AFI = 1
* SAFI = 128
* Length of Next Hop Address field = 24 (or 48)
* Next Hop Address = VPN-IPv6 address of a next hop whose RD is set
to zero
* NLRI = IPv4-VPN routes
During BGP Capability Advertisement, the PE routers would include the
following fields in the Capabilities Optional Parameter:
* Capability Code set to "Extended Next Hop Encoding"
* Capability Value containing <NLRI AFI=1, NLRI SAFI=128, Nexthop
AFI=2>
6.3. IPv4 VPN Multicast over IPv6 Core
The extensions defined in this document may be used for support of
IPv4 multicast VPNs over an IPv6 backbone. In this application, PE
routers would advertise VPN-IPv4 NLRI in the MP_REACH_NLRI along with
an IPv6 next hop.
The MP_REACH_NLRI is encoded with:
* AFI = 1
* SAFI = 129
* Length of Next Hop Address field = 24 (or 48)
* Next Hop Address = VPN-IPv6 address of a next hop whose RD is set
to zero
* NLRI = IPv4-VPN routes
During BGP Capability Advertisement, the PE routers would include the
following fields in the Capabilities Optional Parameter:
* Capability Code set to "Extended Next Hop Encoding"
* Capability Value containing <NLRI AFI=1, NLRI SAFI=129, Nexthop
AFI=2>
7. IANA Considerations
This document does not define any new code points from those included
in [RFC5549].
[RFC5549] added "Extended Next Hop Encoding" to the "Capability
Codes" registry ([IANA-CAP-CODE]), which was created by [RFC5492].
IANA has updated the registration of that entry to refer to this
document. The value allocated for this Capability Code is 5.
8. Security Considerations
This document does not raise any additional security issues beyond
those of BGP-4 and the Multiprotocol Extensions for BGP-4. The same
security mechanisms are applicable.
However, as [RFC4272] discusses, BGP is vulnerable to traffic
diversion attacks. The ability to advertise an IPv6 next hop adds a
new means by which an attacker could cause traffic to be diverted
from its normal path. Such an attack differs from preexisting
vulnerabilities in that traffic could be forwarded to a distant
target across an intervening network infrastructure (e.g., an IPv6
core), allowing an attack to potentially succeed more easily since
less infrastructure would have to be subverted. Potential
consequences include "hijacking" of traffic or denial of service.
Although not expected to be the typical case, the IPv6 address used
as the BGP next-hop address could be an IPv4-mapped IPv6 address (as
defined in [RFC4291]). Configuration of the security mechanisms
potentially deployed by the network operator (such as security checks
on a next-hop address) also need to keep this case in mind.
9. References
9.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC2545] Marques, P. and F. Dupont, "Use of BGP-4 Multiprotocol
Extensions for IPv6 Inter-Domain Routing", RFC 2545,
DOI 10.17487/RFC2545, March 1999,
<https://www.rfc-editor.org/info/rfc2545>.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, DOI 10.17487/RFC4291, February
2006, <https://www.rfc-editor.org/info/rfc4291>.
[RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private
Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, February
2006, <https://www.rfc-editor.org/info/rfc4364>.
[RFC4760] Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
"Multiprotocol Extensions for BGP-4", RFC 4760,
DOI 10.17487/RFC4760, January 2007,
<https://www.rfc-editor.org/info/rfc4760>.
[RFC5492] Scudder, J. and R. Chandra, "Capabilities Advertisement
with BGP-4", RFC 5492, DOI 10.17487/RFC5492, February
2009, <https://www.rfc-editor.org/info/rfc5492>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8277] Rosen, E., "Using BGP to Bind MPLS Labels to Address
Prefixes", RFC 8277, DOI 10.17487/RFC8277, October 2017,
<https://www.rfc-editor.org/info/rfc8277>.
9.2. Informative References
[Err5253] RFC Errata, Erratum ID 5253, RFC 5549,
<https://www.rfc-editor.org/errata/eid5253>.
[IANA-AFI] IANA, "Address Family Numbers",
<https://www.iana.org/assignments/address-family-
numbers/>.
[IANA-CAP-CODE]
IANA, "Capability Codes",
<https://www.iana.org/assignments/capability-codes/>.
[IANA-SAFI]
IANA, "Subsequent Address Family Identifiers (SAFI)
Parameters",
<https://www.iana.org/assignments/safi-namespace/>.
[RFC4272] Murphy, S., "BGP Security Vulnerabilities Analysis",
RFC 4272, DOI 10.17487/RFC4272, January 2006,
<https://www.rfc-editor.org/info/rfc4272>.
[RFC4659] De Clercq, J., Ooms, D., Carugi, M., and F. Le Faucheur,
"BGP-MPLS IP Virtual Private Network (VPN) Extension for
IPv6 VPN", RFC 4659, DOI 10.17487/RFC4659, September 2006,
<https://www.rfc-editor.org/info/rfc4659>.
[RFC4684] Marques, P., Bonica, R., Fang, L., Martini, L., Raszuk,
R., Patel, K., and J. Guichard, "Constrained Route
Distribution for Border Gateway Protocol/MultiProtocol
Label Switching (BGP/MPLS) Internet Protocol (IP) Virtual
Private Networks (VPNs)", RFC 4684, DOI 10.17487/RFC4684,
November 2006, <https://www.rfc-editor.org/info/rfc4684>.
[RFC4798] De Clercq, J., Ooms, D., Prevost, S., and F. Le Faucheur,
"Connecting IPv6 Islands over IPv4 MPLS Using IPv6
Provider Edge Routers (6PE)", RFC 4798,
DOI 10.17487/RFC4798, February 2007,
<https://www.rfc-editor.org/info/rfc4798>.
[RFC4925] Li, X., Ed., Dawkins, S., Ed., Ward, D., Ed., and A.
Durand, Ed., "Softwire Problem Statement", RFC 4925,
DOI 10.17487/RFC4925, July 2007,
<https://www.rfc-editor.org/info/rfc4925>.
[RFC5549] Le Faucheur, F. and E. Rosen, "Advertising IPv4 Network
Layer Reachability Information with an IPv6 Next Hop",
RFC 5549, DOI 10.17487/RFC5549, May 2009,
<https://www.rfc-editor.org/info/rfc5549>.
[RFC5565] Wu, J., Cui, Y., Metz, C., and E. Rosen, "Softwire Mesh
Framework", RFC 5565, DOI 10.17487/RFC5565, June 2009,
<https://www.rfc-editor.org/info/rfc5565>.
[RFC6074] Rosen, E., Davie, B., Radoaca, V., and W. Luo,
"Provisioning, Auto-Discovery, and Signaling in Layer 2
Virtual Private Networks (L2VPNs)", RFC 6074,
DOI 10.17487/RFC6074, January 2011,
<https://www.rfc-editor.org/info/rfc6074>.
[RFC6513] Rosen, E., Ed. and R. Aggarwal, Ed., "Multicast in MPLS/
BGP IP VPNs", RFC 6513, DOI 10.17487/RFC6513, February
2012, <https://www.rfc-editor.org/info/rfc6513>.
[RFC6514] Aggarwal, R., Rosen, E., Morin, T., and Y. Rekhter, "BGP
Encodings and Procedures for Multicast in MPLS/BGP IP
VPNs", RFC 6514, DOI 10.17487/RFC6514, February 2012,
<https://www.rfc-editor.org/info/rfc6514>.
Acknowledgments
The authors would like to thank Francois Le Faucheur and Eric Rosen
for their work on [RFC5549].
The authors would like to thank Yakov Rekhter, Pranav Mehta, and John
Scudder for their contributions to the approach defined in [RFC5549].
Authors' Addresses
Stephane Litkowski
Cisco
Email: slitkows@cisco.com
Swadesh Agrawal
Cisco
Email: swaagraw@cisco.com
Krishna Muddenahally Ananthamurthy
Cisco
Email: kriswamy@cisco.com
Keyur Patel
Arrcus
Email: keyur@arrcus.com