💾 Archived View for gemini.bortzmeyer.org › rfc-mirror › rfc4547.txt captured on 2021-11-30 at 20:18:30.
-=-=-=-=-=-=-
Network Working Group A. Ahmad
Request for Comments: 4547 Cisco Systems Inc.
Category: Standards Track G. Nakanishi
Motorola
June 2006
Event Notification Management Information Base for
Data over Cable Service Interface Specifications (DOCSIS)-Compliant
Cable Modems and Cable Modem Termination Systems
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2006).
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it defines a basic set of managed objects for Simple
Network Management Protocol (SNMP) based event notification
management of Data Over Cable Service Interface Specification
(DOCSIS) compliant Cable Modems and Cable Modem Termination Systems.
This MIB is defined as an extension to the DOCSIS Cable Device MIB.
This memo specifies a MIB module in a manner that is compliant to the
Structure of Management Information Version 2 (SMIv2). The set of
objects is consistent with the SNMP framework and existing SNMP
standards.
Ahmad & Makanishi Standards Track [Page 1]
RFC 4547 Event Notification MIB June 2006
Table of Contents
1. The Internet-Standard Management Framework ......................2
2. Glossary ........................................................2
2.1. BPI - Baseline Privacy Interface ...........................3
2.2. BPI - Baseline Privacy Plus Interface ......................3
2.3. CATV .......................................................3
2.4. CM - Cable Modem ...........................................3
2.5. CMTS - Cable Modem Termination System ......................3
2.6. DOCSIS .....................................................3
2.7. Downstream .................................................4
2.8. Head-end ...................................................4
2.9. MAC Packet .................................................4
2.10. RF ........................................................4
2.11. SID .......................................................4
2.12. TLV .......................................................4
2.13. Upstream ..................................................4
3. Overview ........................................................4
3.1. Structure of the MIB .......................................5
4. Definitions .....................................................5
5. Contributors ...................................................35
6. Acknowledgements ...............................................36
7. Security Considerations ........................................36
8. IANA Considerations ............................................37
9. References .....................................................37
9.1. Normative References ......................................37
9.2. Informative References ....................................38
1. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [16].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [2], STD 58, RFC 2579 [3] and STD 58, RFC 2580 [4].
2. Glossary
The terms in this document are derived either from normal cable
system usage, or from the documents associated with the Data Over
Cable Service Interface Specification (DOCSIS) process.
Ahmad & Makanishi Standards Track [Page 2]
RFC 4547 Event Notification MIB June 2006
2.1. BPI - Baseline Privacy Interface
A mechanism for providing data privacy over the HFC network in DOCSIS
1.0 systems [8].
2.2. BPI - Baseline Privacy Plus Interface
A mechanism that extends the Baseline Privacy Interface with the
addition of CM authentication over the HFC network in DOCSIS 1.1/2.0
systems and beyond [9].
2.3. CATV
Originally "Community Antenna Television", now used to refer to any
cable or hybrid fiber and cable system used to deliver video signals
to a community.
2.4. CM - Cable Modem
A CM acts as a "slave" station in a DOCSIS-compliant cable data
system.
2.5. CMTS - Cable Modem Termination System
A generic term covering a cable bridge or cable router in a head-end.
A CMTS acts as the master station in a DOCSIS-compliant cable data
system. It is the only station that transmits downstream, and it
controls the scheduling of upstream transmissions by its associated
CMs.
2.6. DOCSIS
DOCSIS stands for "Data-over-Cable Service Interface Specifications"
and refers to the ITU-T J.112 Annex B standard for cable modem
systems [10], [13] commonly known as DOCSIS 1.0. The DOCSIS 1.1
specification is an extension of DOCSIS 1.0, with new features to
support quality of service, fragmentation, and requirements for
European cable plants [14].
DOCSIS 2.0 [15] builds upon DOCSIS 1.1 and provides all of the
features and functionality that DOCSIS 1.1 provides. In addition, it
provides some significant enhancements in upstream capacity over
DOCSIS 1.1, such as 30.72 Mbps maximum upstream channel capacity,
Synchronous-Code Division Multiple Access (CDMA) operation, increased
robustness to upstream noise and channel impairments, Enhanced Reed-
Solomon error correction, and Trellis Coded Modulation.
Ahmad & Makanishi Standards Track [Page 3]
RFC 4547 Event Notification MIB June 2006
2.7. Downstream
The direction from the CMTS to the CM.
2.8. Head-end
The origination point in most cable systems of the subscriber video
signals. Generally also the location of the CMTS equipment.
2.9. MAC Packet
A term referring to DOCSIS Protocol Data Unit (PDU).
2.10. RF
A term referring to Radio Frequency.
2.11. SID
A term referring to DOCSIS Service ID. The SID identifies a
particular upstream bandwidth allocation and class-of-service
management for DOCSIS, and identifies a particular bidirectional
security association for BPI.
2.12. TLV
TLV stands for Type/Length/Value. TLV is an encoding method
consisting of three fields. The first field indicates the type of
element, the second field indicates the length of the element, and
the third field contains the element's value.
2.13. Upstream
The direction from the CM to the CMTS.
3. Overview
Offering High Speed Internet Service in the cable industry has become
extremely successful. DOCSIS devices are being deployed at a rate of
multiple thousands per day. Although operators are enjoying
successful deployment, they are also facing the challenge of properly
managing deployed devices. Operators are using Simple Network
Management Protocol, a set of Management Information Base (MIB)
required by DOCSIS, and SNMP Notifications to manage deployed DOCSIS
devices. The usage of SNMP Notification for event reporting is
becoming more popular as an effective and efficient method for
network monitoring.
Ahmad & Makanishi Standards Track [Page 4]
RFC 4547 Event Notification MIB June 2006
Unfortunately, only a minimal set of SNMP Notifications is currently
available. This notification MIB, in conjunction with [11] and [12],
provides a minimum set of standard DOCSIS Notifications that DOCSIS
devices SHOULD support to enable successful management of DOCSIS
devices and networks.
This document defines a set of objects required for the event
notification management of DOCSIS-compliant Cable Modems (CMs) and
Cable Modem Termination Systems (CMTSs). The MIB module is derived
from the DOCSIS [11] and [12].
Appendix H of [11] defines all DOCSIS 1.1 required events, and
Appendix D of [12] does that for DOCSIS 2.0. The notifications
specified in this document are used to notify these events via SNMP.
In this document, the key words "MUST", "MUST NOT", "REQUIRED",
"SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY",
and "OPTIONAL" are to be interpreted as described in RFC 2119 [1].
3.1. Structure of the MIB
This DOCS-IETF-CABLE-DEVICE-NOTIFICATION-MIB was designed to extend
the RFC2669 [5] notification module.
Two groups of SNMP notification objects are defined in this document.
One group defines notifications for cable modem events, and the other
group defines notifications for cable modem termination system
events.
DOCSIS defines numerous events, and each event is assigned to a
functional category. This MIB defines a notification object for each
functional category. The varbinding list of each notification
includes information about the event that occurred on the device.
4. Definitions
The MIB module defined here IMPORTs from SNMPv2-SMI [2], SNMPv2-CONF
[3], DOCS-CABLE-DEVICE-MIB [5], DOCS-IF-MIB [6], and IF-MIB [7].
DOCS-IETF-CABLE-DEVICE-NOTIFICATION-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
mib-2
FROM SNMPv2-SMI -- RFC 2578
MODULE-COMPLIANCE,
Ahmad & Makanishi Standards Track [Page 5]
RFC 4547 Event Notification MIB June 2006
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF -- RFC 2580
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsDevSwFilename,
docsDevSwServer,
docsDevServerDhcp,
docsDevServerTime
FROM DOCS-CABLE-DEVICE-MIB -- RFC 2669
docsIfCmCmtsAddress,
docsIfCmtsCmStatusMacAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType,
docsIfCmtsCmStatusDocsisRegMode,
docsIfCmtsCmStatusModulationType
FROM DOCS-IF-MIB -- RFC 4546
ifPhysAddress
FROM IF-MIB; -- RFC 2863
docsDevNotifMIB MODULE-IDENTITY
LAST-UPDATED "200605240000Z" -- May 24, 2006
ORGANIZATION "IETF IP over Cable Data Network
Working Group"
CONTACT-INFO
" Azlina Ahmad
Postal: Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134, U.S.A.
Phone: 408 853 7927
E-mail: azlina@cisco.com
Greg Nakanishi
Postal: Motorola
6450 Sequence Drive
San Diego, CA 92121, U.S.A.
Phone: 858 404 2366
E-mail: gnakanishi@motorola.com
IETF IPCDN Working Group
General Discussion: ipcdn@ietf.org
Ahmad & Makanishi Standards Track [Page 6]
RFC 4547 Event Notification MIB June 2006
Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn
Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn
Co-chairs: Richard Woundy,
richard_woundy@cable.comcast.com
Jean-Francois Mule, jf.mule@cablelabs.com"
DESCRIPTION
"The Event Notification MIB is an extension of the
CABLE DEVICE MIB. It defines various notification
objects for both cable modem and cable modem termination
systems. Two groups of SNMP notification objects are
defined. One group is for notifying cable modem events,
and one group is for notifying cable modem termination
system events.
DOCSIS defines numerous events, and each event is
assigned to a functional category. This MIB defines
a notification object for each functional category.
The varbinding list of each notification includes
information about the event that occurred on the
device.
Copyright (C) The Internet Society (2006). This version
of this MIB module is part of RFC 4547; see the RFC
itself for full legal notices."
REVISION "200605240000Z" -- May 24, 2006
DESCRIPTION
"Initial version, published as RFC 4547."
::= { mib-2 132 }
docsDevNotifControl OBJECT IDENTIFIER ::= { docsDevNotifMIB 1}
docsDevCmNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 2 0 }
docsDevCmtsNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 3 0 }
docsDevCmNotifControl OBJECT-TYPE
SYNTAX BITS {
cmInitTLVUnknownNotif( 0),
cmDynServReqFailNotif( 1),
cmDynServRspFailNotif( 2),
cmDynServAckFailNotif( 3),
cmBpiInitNotif( 4),
cmBPKMNotif( 5),
cmDynamicSANotif( 6),
cmDHCPFailNotif( 7),
cmSwUpgradeInitNotif( 8),
cmSwUpgradeFailNotif( 9),
cmSwUpgradeSuccessNotif( 10),
Ahmad & Makanishi Standards Track [Page 7]
RFC 4547 Event Notification MIB June 2006
cmSwUpgradeCVCNotif( 11),
cmTODFailNotif( 12),
cmDCCReqFailNotif( 13),
cmDCCRspFailNotif( 14),
cmDCCAckFailNotif( 15)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object is used to enable specific CM notifications.
For example, if the first bit is set, then
docsDevCmInitTLVUnknownNotif is enabled. If it is not set,
the notification is disabled. Note that notifications are
also under the control of the MIB modules defined in
RFC3413.
If the device is rebooted,the value of this object SHOULD
revert to the default value.
"
DEFVAL { {} }
::= { docsDevNotifControl 1 }
docsDevCmtsNotifControl OBJECT-TYPE
SYNTAX BITS {
cmtsInitRegReqFailNotif( 0),
cmtsInitRegRspFailNotif( 1),
cmtsInitRegAckFailNotif( 2),
cmtsDynServReqFailNotif( 3),
cmtsDynServRspFailNotif( 4),
cmtsDynServAckFailNotif( 5),
cmtsBpiInitNotif( 6),
cmtsBPKMNotif( 7),
cmtsDynamicSANotif( 8),
cmtsDCCReqFailNotif( 9),
cmtsDCCRspFailNotif( 10),
cmtsDCCAckFailNotif( 11)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object is used to enable specific CMTS notifications.
For example, if the first bit is set, then
docsDevCmtsInitRegRspFailNotif is enabled. If it is not set,
the notification is disabled. Note that notifications are
also under the control of the MIB modules defined in
RFC3413.
Ahmad & Makanishi Standards Track [Page 8]
RFC 4547 Event Notification MIB June 2006
If the device is rebooted,the value of this object SHOULD
revert to the default value.
"
DEFVAL { {} }
::= { docsDevNotifControl 2 }
docsDevCmInitTLVUnknownNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"Notification to indicate that an unknown TLV was
encountered during the TLV parsing process.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 1 }
Ahmad & Makanishi Standards Track [Page 9]
RFC 4547 Event Notification MIB June 2006
docsDevCmDynServReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic service
request during the dynamic services process.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected to (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 2 }
docsDevCmDynServRspFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
Ahmad & Makanishi Standards Track [Page 10]
RFC 4547 Event Notification MIB June 2006
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
" A notification to report the failure of a dynamic service
response during the dynamic services process.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 3}
docsDevCmDynServAckFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
Ahmad & Makanishi Standards Track [Page 11]
RFC 4547 Event Notification MIB June 2006
"A notification to report the failure of a dynamic service
acknowledgement during the dynamic services process.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 4}
docsDevCmBpiInitNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a BPI
initialization attempt during the registration process.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
Ahmad & Makanishi Standards Track [Page 12]
RFC 4547 Event Notification MIB June 2006
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 5 }
docsDevCmBPKMNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a Baseline
Privacy Key Management (BPKM) operation.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
Ahmad & Makanishi Standards Track [Page 13]
RFC 4547 Event Notification MIB June 2006
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 6 }
docsDevCmDynamicSANotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic security
association operation.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
Ahmad & Makanishi Standards Track [Page 14]
RFC 4547 Event Notification MIB June 2006
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 7 }
docsDevCmDHCPFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsDevServerDhcp,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a DHCP operation.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevServerDhcp: the IP address of the DHCP server.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 8 }
Ahmad & Makanishi Standards Track [Page 15]
RFC 4547 Event Notification MIB June 2006
docsDevCmSwUpgradeInitNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsDevSwFilename,
docsDevSwServer,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to indicate that a software upgrade
has been initiated on the device.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 9 }
docsDevCmSwUpgradeFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
Ahmad & Makanishi Standards Track [Page 16]
RFC 4547 Event Notification MIB June 2006
ifPhysAddress,
docsIfCmCmtsAddress,
docsDevSwFilename,
docsDevSwServer,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a software upgrade
attempt.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevSwFilename: the software image file name
- docsDevSwServer: the IP address of the server that
the image is retrieved from.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 10 }
docsDevCmSwUpgradeSuccessNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
Ahmad & Makanishi Standards Track [Page 17]
RFC 4547 Event Notification MIB June 2006
docsDevSwFilename,
docsDevSwServer,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the software upgrade success
status.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevSwFilename: the software image file name
- docsDevSwServer: the IP address of the server that
the image is retrieved from.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 11 }
docsDevCmSwUpgradeCVCFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
Ahmad & Makanishi Standards Track [Page 18]
RFC 4547 Event Notification MIB June 2006
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report that the verification of the
code file has failed during a secure software upgrade
attempt.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 12 }
docsDevCmTODFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsDevServerTime,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a time of day
Ahmad & Makanishi Standards Track [Page 19]
RFC 4547 Event Notification MIB June 2006
operation.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevServerTime: the IP address of the time server.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 13 }
docsDevCmDCCReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
" A notification to report the failure of a dynamic channel
change request during the dynamic channel change process
on the CM.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
Ahmad & Makanishi Standards Track [Page 20]
RFC 4547 Event Notification MIB June 2006
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 14 }
docsDevCmDCCRspFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change response during the dynamic channel
change process on the CM.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
Ahmad & Makanishi Standards Track [Page 21]
RFC 4547 Event Notification MIB June 2006
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 15 }
docsDevCmDCCAckFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change acknowledgement during the dynamic channel
change process on the CM.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
Ahmad & Makanishi Standards Track [Page 22]
RFC 4547 Event Notification MIB June 2006
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmtsCmStatusModulationType the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 16}
docsDevCmtsInitRegReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a registration
request from a CM during the CM initialization
process that was detected on the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
Ahmad & Makanishi Standards Track [Page 23]
RFC 4547 Event Notification MIB June 2006
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 1 }
docsDevCmtsInitRegRspFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a registration
response during the CM initialization
process that was detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 2 }
docsDevCmtsInitRegAckFailNotif NOTIFICATION-TYPE
Ahmad & Makanishi Standards Track [Page 24]
RFC 4547 Event Notification MIB June 2006
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a registration
acknowledgement from the CM during the CM
initialization process that was detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 3 }
docsDevCmtsDynServReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
Ahmad & Makanishi Standards Track [Page 25]
RFC 4547 Event Notification MIB June 2006
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic service
request during the dynamic services process
that was detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 4 }
docsDevCmtsDynServRspFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
Ahmad & Makanishi Standards Track [Page 26]
RFC 4547 Event Notification MIB June 2006
"A notification to report the failure of a dynamic service
response during the dynamic services process
that was detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 5 }
docsDevCmtsDynServAckFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic service
acknowledgement during the dynamic services
process that was detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
Ahmad & Makanishi Standards Track [Page 27]
RFC 4547 Event Notification MIB June 2006
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 6 }
docsDevCmtsBpiInitNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a BPI
initialization attempt during the CM registration process
that was detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
Ahmad & Makanishi Standards Track [Page 28]
RFC 4547 Event Notification MIB June 2006
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 7 }
docsDevCmtsBPKMNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a BPKM operation
that is detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
Ahmad & Makanishi Standards Track [Page 29]
RFC 4547 Event Notification MIB June 2006
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 8 }
docsDevCmtsDynamicSANotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic security
association operation that is detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
Ahmad & Makanishi Standards Track [Page 30]
RFC 4547 Event Notification MIB June 2006
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 9 }
docsDevCmtsDCCReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change request during the dynamic channel
change process and is detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 10 }
docsDevCmtsDCCRspFailNotif NOTIFICATION-TYPE
Ahmad & Makanishi Standards Track [Page 31]
RFC 4547 Event Notification MIB June 2006
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change response during the dynamic channel
change process and is detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 11 }
docsDevCmtsDCCAckFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
Ahmad & Makanishi Standards Track [Page 32]
RFC 4547 Event Notification MIB June 2006
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change acknowledgement during the dynamic channel
change process and is detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 12}
--
--Conformance definitions
--
docsDevNotifConformance OBJECT IDENTIFIER
::= { docsDevNotifMIB 4 }
docsDevNotifGroups OBJECT IDENTIFIER
::= { docsDevNotifConformance 1 }
docsDevNotifCompliances OBJECT IDENTIFIER
::= { docsDevNotifConformance 2 }
docsDevCmNotifCompliance MODULE-COMPLIANCE
STATUS current
Ahmad & Makanishi Standards Track [Page 33]
RFC 4547 Event Notification MIB June 2006
DESCRIPTION
"The compliance statement for CM Notifications and Control."
MODULE --docsDevNotif
MANDATORY-GROUPS {
docsDevCmNotifControlGroup,
docsDevCmNotificationGroup
}
::= { docsDevNotifCompliances 1 }
docsDevCmNotifControlGroup OBJECT-GROUP
OBJECTS {
docsDevCmNotifControl
}
STATUS current
DESCRIPTION
"This group represents objects that allow control
over CM Notifications."
::= { docsDevNotifGroups 1 }
docsDevCmNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
docsDevCmInitTLVUnknownNotif,
docsDevCmDynServReqFailNotif,
docsDevCmDynServRspFailNotif,
docsDevCmDynServAckFailNotif,
docsDevCmBpiInitNotif,
docsDevCmBPKMNotif,
docsDevCmDynamicSANotif,
docsDevCmDHCPFailNotif,
docsDevCmSwUpgradeInitNotif,
docsDevCmSwUpgradeFailNotif,
docsDevCmSwUpgradeSuccessNotif,
docsDevCmSwUpgradeCVCFailNotif,
docsDevCmTODFailNotif,
docsDevCmDCCReqFailNotif,
docsDevCmDCCRspFailNotif,
docsDevCmDCCAckFailNotif
}
STATUS current
DESCRIPTION
"A collection of CM notifications providing device status
and control."
::= { docsDevNotifGroups 2 }
docsDevCmtsNotifCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
Ahmad & Makanishi Standards Track [Page 34]
RFC 4547 Event Notification MIB June 2006
"The compliance statement for DOCSIS CMTS Notification
and Control."
MODULE --docsDevNotif
MANDATORY-GROUPS {
docsDevCmtsNotifControlGroup,
docsDevCmtsNotificationGroup
}
::= { docsDevNotifCompliances 2 }
docsDevCmtsNotifControlGroup OBJECT-GROUP
OBJECTS {
docsDevCmtsNotifControl
}
STATUS current
DESCRIPTION
"This group represents objects that allow control
over CMTS Notifications."
::= { docsDevNotifGroups 3 }
docsDevCmtsNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
docsDevCmtsInitRegReqFailNotif,
docsDevCmtsInitRegRspFailNotif,
docsDevCmtsInitRegAckFailNotif ,
docsDevCmtsDynServReqFailNotif,
docsDevCmtsDynServRspFailNotif,
docsDevCmtsDynServAckFailNotif,
docsDevCmtsBpiInitNotif,
docsDevCmtsBPKMNotif,
docsDevCmtsDynamicSANotif,
docsDevCmtsDCCReqFailNotif,
docsDevCmtsDCCRspFailNotif,
docsDevCmtsDCCAckFailNotif
}
STATUS current
DESCRIPTION
"A collection of CMTS notifications providing device
status and control."
::= { docsDevNotifGroups 4 }
END
5. Contributors
Thanks go to the following people, who have made significant
contributions to this document: Junming Gao, Jean-Francois Mule, Dave
Raftus, Pak Siripunkaw, and Rich Woundy.
Ahmad & Makanishi Standards Track [Page 35]
RFC 4547 Event Notification MIB June 2006
6. Acknowledgements
This document was produced by the IPCDN Working Group. Thanks to
Harrie Hazewinkel and Bert Wijnen for their thorough review and
insightful comments on this document. Special thanks to Rich Woundy,
who made several valuable suggestions to improve the notifications.
7. Security Considerations
There are two management objects defined in this MIB module with a
MAX-ACCESS clause of read-write and/or read-create
(docsDevCmNotifControl and docsDevCmtsNotifControl). Such objects
may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations.
Setting docsDevCmNotifControl or docsDevCmtsNotifControl may cause
flooding of notifications, which can disrupt network service.
Besides causing "flooding", changing the objects can also mean that
notifications will not be emitted when one intends that to happen.
This MIB defines a number of notification objects that send detailed
information about the event that caused the generation of the
notification. Information in the notification message includes:
event priority, the event Id, the event message body, the CM DOCSIS
capability, the CM DOCSIS QOS level, the CM DOCSIS upstream
modulation type, the cable interface MAC address of the cable modem,
and the cable card MAC address of the CMTS to which the modem is
connected. The monitoring of these notification messages could be
used to gather information about the state of the network and devices
(CM and CMTS) attached to the network.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPSec),
even then there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [16], section 8), including
full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
Ahmad & Makanishi Standards Track [Page 36]
RFC 4547 Event Notification MIB June 2006
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
8. IANA Considerations
The MIB module defined in this document uses the following IANA-
assigned OBJECT IDENTIFIER values recorded in the SMI Numbers
registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
docsDevNotifMIB { mib-2 132 }
9. References
9.1. Normative References
[1] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[2] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Structure
of Management Information Version 2 (SMIv2)", STD 58, RFC 2578,
April 1999.
[3] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Textual
Conventions for SMIv2", STD 58, RFC 2579, April 1999.
[4] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance
Statements for SMIv2", STD 58, RFC 2580, April 1999.
[5] St. Johns, M., "DOCSIS Cable Device MIB Cable Device Management
Information Base for DOCSIS compliant Cable Modems and Cable
Modem Termination Systems", RFC 2669, August 1999.
[6] Raftus, D. and E. Cardona, "Radio Frequency (RF) Interface
Management Information Base for Data over Cable Service
Interface Specifications (DOCSIS) 2.0 Compliant RF Interfaces",
RFC 4546, June 2006.
[7] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB",
RFC 2863, June 2000.
[8] SCTE Data Standards Subcommittee, "Data-Over-Cable Service
Interface Specifications: DOCSIS 1.0 Baseline Privacy Interface
Specification SCTE 22-2", 2002,
<http://www.scte.org/standards/>.
Ahmad & Makanishi Standards Track [Page 37]
RFC 4547 Event Notification MIB June 2006
[9] CableLabs, "Baseline Privacy Plus Interface Specification SP-
BPI+040407", April 2004,
<http://www.cablemodem.com/specifications/>.
[10] SCTE Data Standards Subcommittee, "Data-Over-Cable Service
Interface Specifications: DOCSIS 1.0 Operations Support System
Interface Specification Radio Frequency Interface SCTE 22-3",
2002, <http://www.scte.org/standards/>.
[11] CableLabs, "Data-Over-Cable Service Interface Specifications:
Operations Support System Interface Specification CM-SP-
OSSIv1.1-C01-050907", September 2005,
<http://www.cablemodem.com/specifications/>.
[12] CableLabs, "Data-Over-Cable Service Interface Specifications:
Operations Support System Interface Specification CM-SP-
OSSIv2.0-I09-050812", August 2005,
<http://www.cablemodem.com/specifications/>.
[13] SCTE Data Standards Subcommittee, "Data-Over-Cable Service
Interface Specifications: DOCSIS 1.0 Radio Frequency Interface
Specification SCTE 22-1", 2002,
<http://www.scte.org/standards/>.
[14] CableLabs, "Data-Over-Cable Service Interface Specifications:
Radio Frequency Interface Specification CM-SP-RFIv1.1-C01-
050907", September 2005,
<http://www.cablemodem.com/specifications/>.
[15] CableLabs, "Data-Over-Cable Service Interface Specifications:
Radio Frequency Interface Specification CM-SP-RFIv2.0-I10-
051209", December 2005,
<http://www.cablemodem.com/specifications/>.
9.2. Informative References
[16] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction
and Applicability Statements for Internet-Standard Management
Framework", RFC 3410, December 2002.
Ahmad & Makanishi Standards Track [Page 38]
RFC 4547 Event Notification MIB June 2006
Authors' Addresses
Azlina Ahmad
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134
US
Phone: 408 853 7927
EMail: azlina@cisco.com
Greg Nakanishi
Motorola
6450 Sequence Dr.
San Diego, CA 92126
US
Phone: 858 404-2366
EMail: gnakanishi@motorola.com
Ahmad & Makanishi Standards Track [Page 39]
RFC 4547 Event Notification MIB June 2006
Full Copyright Statement
Copyright (C) The Internet Society (2006).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Ahmad & Makanishi Standards Track [Page 40]