HELP! P1S Filament Cutter problem.

https://v.redd.it/me6w1w7ihm6d1

created by PopularStu on 14/06/2024 at 23:34 UTC

5 upvotes, 10 top-level comments (showing 10)

I got this P1S yesterday, and it prints really well... But at the end of every print it does this. (4 prints so far)

I'll post the settings in the replies. (New to posting)

Comments

Comment by chemape876 at 15/06/2024 at 00:08 UTC

9 upvotes, 2 direct replies

are you using custom gcode? because my printer doesn't cut the filament 3 times.

Comment by [deleted] at 15/06/2024 at 01:08 UTC*

3 upvotes, 3 direct replies

So I can see one fault: the lever is not pushed in far enough for the magnet from the lever to come close to the sensor. This means that the printer doesn't even notice that the filament has been cut or that the lever has moved. This is probably why it tries three times. This has nothing to do with the housing jumping off, but is something jammed? Can you move the lever?

Actually, the head should be driving on the left side towards a "stud". Somehow I don't see the part on your video? Is that missing? That could also explain why the lever is not pressed. Sorry for the bad photo. There must be a plastic piece, I don't see that in your video.

*Edit**: Now I'm sure, exactly at second 19 it pushes the plastic part away, doesn't catch the lever and that's the reason why your housing jumps away. See second comment. I can't see it exactly, either it's missing something or... no idea, but that shouldn't happen.

https://preview.redd.it/3zqf74k0ym6d1.jpeg?width=1772&format=pjpg&auto=webp&s=cb54956f24fe655fbd50c82ad09b65cd8d161e77

Comment by DistanceOk5828 at 15/06/2024 at 13:05 UTC

3 upvotes, 0 direct replies

Sorry for your problem BUT... My stomach hurt from laughing at this i don't know why!

2 upvotes, 0 direct replies

https://preview.redd.it/7wavmu9phm6d1.png?width=732&format=pjpg&auto=webp&s=58afa8145239ec5ae97322fd05b8b2702b70dc33

Comment by KrackSmellin at 15/06/2024 at 03:18 UTC

2 upvotes, 1 direct replies

Because the moment the front fell off - we didn’t get it - you continued to show us until it not only fell off but CONTINUED to run.

1 upvotes, 0 direct replies

https://preview.redd.it/23gnlj7nhm6d1.png?width=423&format=pjpg&auto=webp&s=a9722da845004253998adf8d2fcb7922f24592ea

Comment by Lulzicon1 at 15/06/2024 at 02:14 UTC

1 upvotes, 1 direct replies

Reset the entire printer to factory. Reset bambu studio to factory. Try again. Redo the calibration. Confirn to yourself that you Change nothing.

If it persists after a complete factory Reset, put in a ticket to bambu.

Comment by BU1_3x at 15/06/2024 at 04:21 UTC

1 upvotes, 1 direct replies

Ummmmm.. yikes. Did you happen to do the firmware update today? I'm wondering if that may be part of the problem..

Comment by BU1_3x at 17/06/2024 at 02:46 UTC

1 upvotes, 0 direct replies

Hey, do you have blue filament in there or is that pfe tube coming out of the extruder blue!?!?!

Comment by Next_Charge_1897 at 28/07/2024 at 08:03 UTC

1 upvotes, 1 direct replies

I have the same problem. Was it solved?